Fix the checkpatch warning as below:
WARNING: Prefer netdev_err(netdev, ... then dev_err(dev, ... then pr_err(... to printk(KERN_ERR ...
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The original sa1100_rtc_open/sa1100_rtc_release will be called when the
/dev/rtc0 is opened or closed. In fact, these two functions will
enable/disable the clock. Disabling clock will make rtc not work. So
only enable/disable clock when probe/remove the device.
Signed-off-by: Chao Xie <chao.xie@marvell.com>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Leo Song <liangs@marvell.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add an rtc driver for Maxim 8997 multifunction chip. Max8997 has rtc
module in it. and it can be used for timekeeping clock and system alarm.
It provide various operational mode those are BCD/binary, 24/12hour,
am/pm. Driver sets binary/24/ for default. Maxim 8997 also supports
SMPL(Sudden Momentary Power Loss), WTSR (Watchdog Timeout and Software
Reset).
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Cc: Devendra Naga <devendra.aaru@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use dev_dbg() instaed of pr_debug() to be consistent.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The Armada 370 and Armada XP Socs have the same controller that the one
used in the orion platforms. This patch updates the device tree for
these SoCs.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mark the pl031 as wake-up capable so that rtcwake and suspend test can work.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
All interrupt get disabled during system suspend and enabled during system
resume. The enabling/disabling of interrupt happen in sequence of
interrupt registration with framework.
Therefore, in resume, the parent interrupt of this device enabled before
the RTC irq interrupt enabled. If RTC is enabled for alarm wake and if
system wake by alarm then there is interrupt pending for RTC. In resume,
the parent interrupt get enabled before the rtc interrupt and hence ISR
get served. In ISR, it founds that rtc interrupt is disabled and so it
does not call the rtc isr handler and hence it misses the interrupt.
Setting flag for early resume so that rtc interrupt get enabled before
parent interrupt and so rtc interrupt get enabled when parent interrupt
handler check for interrupt of device and call the rtc handler if it is
there. This way it will not miss the interrupt.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use SET_SYSTEM_SLEEP_PM_OPS for setting suspend/resume callbacks for
dev_pm_ops.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The driver stores the interrupt enable register before going to suspend
and restore in resume. Also it enables alarm before going to suspend.
The driver only write the Interrupt enable register for enabling ALARM and
does not enable any other bits. So it is not require to save complete
register and enable ALARM interrupt before suspend and restore in resume.
Also ALARM interrupt already enable if alarm is enabled before going to
suspend and hence it is not require to enable explictly in suspend.
Removing such above code.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Making the rtc driver as wakeup capabale and leaving the wake
enable/disable decision to user space through a sysfs attribute.
In suspend, enable wake if device wakeup enabled. In resume disable wake
again.
This change is inline with the Documentation/power/devices.txt#
/sys/devices/.../power/wakeup files
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add an RTC driver for TPS80031/TPS80032 chips by TI. This driver
supports:
- Setting and getting time and date.
- Setting and reading alarm time.
- Alarm and interrupt functionlity.
[akpm@linux-foundation.org: remove obsolete __devinit/__devexit]
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Devendra Naga <devendra.aaru@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove removes some code duplication by using module_platform_driver().
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Found by Coccinelle: http://coccinelle.lip6.fr/
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
pxa-rtc is widely used in pxa27x/pxa3xx/pxa93x/pxa95x. Checking cpuid in
pxa-rtc driver is unnecessary since we assign on-chip device in soc files.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This eliminates having an #ifdef returning NULL for the case when OF is
disabled. Maintains consistency in cases where OF is always selected.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Implement reading of the battery voltage low signal for rtc-pcf8523.
The bit is read-only and cannot be cleared by software, so no
clear function is implemented.
[akpm@linux-foundation.org: omit pcf8563_rtc_ioctl() if CONFIG_RTC_INTF_DEV=n]
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Reviewed-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a driver to support max77686 rtc. MAX77686 rtc support smpl and wtsr
mode. It has two alarm register which can be used for alarming to wake
system up. This drvier uses regmap to access its register.
[akpm@linux-foundation.org: remove inline, __devinit annotations]
[jg1.han@samsung.com: fix build warnings]
[akpm@linux-foundation.org: simplify code]
Signed-off-by: Chiwoong Byun <woong.byun@samsung.com>
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Myugnjoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix alarm can't wake up system issue
Signed-off-by: Leo Song <liangs@marvell.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix pxa rtc alarm issue by setting week of month and day of week in
rdar/rdcr or it would not match.
Signed-off-by: Leo Song <liangs@marvell.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We can use user_ns, which is also assigned from task_cred_xxx(tsk,
user_ns), at the beginning of copy_namespaces().
Signed-off-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Acked-by: Serge Hallyn <serge.hallyn@canonical.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In fill_elf_header(), elf->e_ident[EI_OSABI] is always set to ELF_OSABI,
so remove the unused argument 'osabi'.
Signed-off-by: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Do not test udelay() for a value less than 10usec when passed a variable
instead of a hard-coded number; there is no way for checkpatch to know the
value of the variable. As it is today, it will complain about variables
with alphanumeric characters plus '_', e.g. foo_bar, but not variables
with other characters, eg. foo->bar.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Cc: Andy Whitcroft <apw@canonical.com>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
kcalloc is sometimes misused with the first and second arguments switched.
Same issue with kmalloc_array too.
Bleat if sizeof is the first argument
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I'm getting a ton of these:
WARNING: Avoid CamelCase: <PageTransHuge>
#140: FILE: mm/migrate.c:1576:
+ if (PageTransHuge(page) && page_count(page) != 3) {
So exclude anything which starts with "Page".
Tested-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Get people to stop adding __devinit and __devexit section markings.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Andy Whitcroft <apw@canonical.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add YA check to printk style.
dev_<level> uses are functions and generate smaller
object code than dev_printk(KERN_<LEVEL>.
Signed-off-by: Joe Perches <joe@perches.com>
Cc: Andy Whitcroft <apw@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Change the defautl XZ_DEC_* config symbol to match the configured
architecture. It is perfectly legitimate to support multiple XZ BCJ
filters for different architectures (e.g.: to mount foreign squashfs/xz
compressed filesystems), it is however more natural not to select them all
by default, but only the one matching the configured architecture.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Acked-by: Lasse Collin <lasse.collin@tukaani.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove the XZ_DEC_* depedencey on CONFIG_EXPERT as recommended by Lasse
Colin.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Acked-by: Lasse Collin <lasse.collin@tukaani.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Group all architecture-specific BCJ filter configuration symbols under an
if XZ_BCJ / endif statement.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Acked-by: Lasse Collin <lasse.collin@tukaani.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
match_number() has return values of -ENOMEM, -EINVAL and -ERANGE. So, for
all the functions calling match_number, the return value should include
these values. Fix up the comments to reflect the correct values.
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Amit Sahrawat <a.sahrawat@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Getting the brightness value is not critical, no need to read the actual
register value. To simplify it, just return the 'bl->props.brightness'
value. Then, lp855x_read_byte() can be removed, not used any more.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
LP8557 is one of LP855x family device, but it has different register map
and initialization process. To support this device, device specific
configuration is done through the lp855x_device_config structure.
Few register definitions are fixed for better readability.
BRIGHTNESS_CTRL -> LP855X_BRIGHTNESS_CTRL
DEVICE_CTRL -> LP855X_DEVICE_CTRL
EEPROM_START -> LP855X_EEPROM_START
EEPROM_END -> LP855X_EEPROM_END
EPROM_START -> LP8556_EPROM_START
EPROM_END -> LP8556_EPROM_END
And LP8557 register definitions are added. New register function,
lp855x_update_bit() is added.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
At this moment, LP855x device driver has fixed register configuration.
For example, fixed register addresses and values are set on the device
initialization. But new device of LP855x family, LP8557 has different
register map and initialization sequence. To support new device
architecture, initialization process should be changed.
Introduce new structure: lp855x_device_config
=============================================
With lp855x_device_config, device specific features are configurable.
Use configurable function calls and register addresses rather than fixed values.
Change on device initialization
===============================
In old LP855x driver architecture, the device initialization was simple.
- Just update the brightness/device control register/ROM area(optional).
In new LP855x driver architecture, two more works are added - pre_init and
post_init.
Those init functions are optional, used for new device LP8557.
New device initialization flow: generic sequence
=================================================
1) pre_init_device()
2) update the brightness register
3) update the device control register
4) update ROM area if need
5) post_init_device()
Name change
===========
Use generic name 'lp855x_configure()' instead of 'lp855x_init_registers()'.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Clearing the NSTBY bit in the control register also automatically clears
the BLEN bit. So we need to make sure to set it again during resume,
otherwise the backlight will stay off.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There is no need to return -EIO, because backlight_device_register()
already returns correct error values.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Daniel Jeong <daniel.jeong@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
gamma_table has 3 arrays which each hold MAX_GAMMA_LEVEL pointers to int.
The current code sets ->gamma_table_count to 6 on 64bit arches and to 3 on
32 bit arches. It should be 3 on everything.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Jingoo Han <jg1.han@samsung.com>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
of_find_node_by_name() returns a node pointer with refcount incremented,
use of_node_put() on it when done.
of_find_node_by_name() will call of_node_put() against the node pass to
from parameter, thus we also need to call of_node_get(from) before calling
of_find_node_by_name().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Cc: Jingoo Han <jg1.han@samsung.com>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is an initial commit of a backlight driver, using step-up DCDC
power supplies on AS3711 PMIC. Only one mode has actually been tested,
several further modes have been implemented "dry," but disabled to avoid
accidental hardware damage. Anyone wishing to use any of those modes
will have to modify the driver.
Tested on sh73a0-based kzm9g board. Only one mode has been tested and
is enabled. That mode copies the sample code from the manufacturer.
Deviations from that code proved to be fatal for the hardware...
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Magnus Damm <magnus.damm@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix up indenting. Also alphasort all entries, which reduces patch
collisions.
Cc: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
devm_regulator_bulk_get is device managed and saves some cleanup
and exit code.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Cc: Alberto Panizzo <maramaopercheseimorto@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The APIs are returning correctly the err codes, no need to assign -EIO
to the ret again.
Signed-off-by: Devendra Naga <devendra.aaru@gmail.com>
Acked-by: Daniel Jeong <daniel.jeong@ti.com>
Cc: G.Shark Jeong <gshark.jeong@gmail.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use the wrapper function for getting the driver data using lcd_device
instead of using dev_get_drvdata with &ld->dev, so we can directly pass a
struct lcd_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use the wrapper function for getting the driver data using
backlight_device instead of using dev_get_drvdata with &bd->dev, so we can
directly pass a struct backlight_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use the wrapper function for getting the driver data using
backlight_device instead of using dev_get_drvdata with &bd->dev, so we can
directly pass a struct backlight_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jingoo Han