Enable virtual to physical translation patching by default in all
kernels. Hide the option behind EMBEDDED.
This can still be turned off if people desire, and they know what
they're doing, to shrink the size of the kernel to a minimum.
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This has now been well tested, and several platforms are now selecting
this directly. It's time to drop its experimental status.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
With the UM_SIGNAL alignment fault mode, no siginfo structure is
passed to userspace.
POSIX specifies how siginfo_t should be populated for alignment
faults, so this patch does just that:
* si_signo = SIGBUS
* si_code = BUS_ADRALN
* si_addr = misaligned data address at which access was attempted
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Kirill A. Shutemov <kirill@shutemov.name>
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Currently, it's possible to set the kernel to ignore alignment
faults when changing the alignment fault handling mode at runtime
via /proc/sys/alignment, even though this is undesirable on ARMv6
and above, where it can result in infinite spins where an un-fixed-
up instruction repeatedly faults.
In addition, the kernel clobbers any alignment mode specified on
the command-line if running on ARMv6 or above.
This patch factors out the necessary safety check into a couple of
new helper functions, and checks and modifies the fault handling
mode as appropriate on boot and on writes to /proc/cpu/alignment.
Prior to ARMv6, the behaviour is unchanged.
For ARMv6 and above, the behaviour changes as follows:
* Attempting to ignore faults on ARMv6 results in the mode being
forced to UM_FIXUP instead. A warning is printed if this
happened as a result of a write to /proc/cpu/alignment. The
user's UM_WARN bit (if present) is still honoured.
* An alignment= argument from the kernel command-line is now
honoured, except that the kernel will modify the specified mode
as described above. This is allows modes such as UM_SIGNAL and
UM_WARN to be active immediately from boot, which is useful for
debugging purposes.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
poison_init_mem() used a loop of:
while ((count = count - 4))
which has 2 problems - an off by one error so that we do one less word
than we should, and the other is that if count == 0 then we loop forever
and poison too much. On a platform with HAVE_TCM=y but nothing in the
TCM's, this caused corruption and the platform failed to boot.
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The file mm/proc-arm946.S contains a typo and is missing a structure
member in __arm946_proc_info. The former prevents compilation
and the latter causes problems during boot. It is likely this
file was manually copied from a similar file and not tested, then
later updates to the *_proc_info structures missed this file.
This patch will apply (with offset) with or without the
recent macro unification work that has been done in this directory.
This was verified against linux-next/stable last week.
See arm-linux-kernel thread:
http://lists.arm.linux.org.uk/lurker/message/20110718.103237.0106d468.en.html
Signed-off-by: Brian S. Julin <bri@abrij.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Unfortunately, the module fixups cause the kernel to fail to build
when SMP is not enabled. Fix this by removing the reference to
fixup_smp on non-SMP fixup kernels, but ensuring that if we do have
the SMP fixup section, we refuse to load the module.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix:
arch/cris/arch-v10/kernel/irq.c:239: error: implicit declaration of function 'kgdb_init'
arch/cris/arch-v10/kernel/irq.c:240: error: implicit declaration of function 'breakpoint'
Declare these two functions.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: WANG Cong <xiyou.wangcong@gmail.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix:
arch/cris/arch-v10/drivers/sync_serial.c:628: error: 'ret' undeclared (first use in this function)
'ret' should be 'err'.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: WANG Cong <xiyou.wangcong@gmail.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix this error:
kernel/fork.c:267: error: implicit declaration of function 'alloc_thread_info_node'
This is due to renaming alloc_thread_info() to alloc_thread_info_node().
[akpm@linux-foundation.org: coding-style fixes]
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: WANG Cong <xiyou.wangcong@gmail.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
arch/tile/mm/init.c: trivial: use BUG_ON
arch/tile: remove useless set_fixmap_nocache() macro
arch/tile: add hypervisor-based character driver for SPI flash ROM
ioctl-number.txt: add the tile hardwall ioctl range
tile: use generic-y format for one-line asm-generic headers
clocksource: tile: convert to use clocksource_register_hz
Use BUG_ON(x) rather than if(x) BUG();
The semantic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@ identifier x; @@
-if (x) BUG();
+BUG_ON(x);
@@ identifier x; @@
-if (!x) BUG();
+BUG_ON(!x);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Migrate the driver for the v7-based MSM chips into drivers/gpio. The
driver is unchanged, only moved.
Change-Id: I810db5b50b71cdca4e869aa0d0310f7f48781a55
Signed-off-by: David Brown <davidb@codeaurora.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Migrate the driver for the v6-based MSM chips into drivers/gpio. The
driver is unchanged, only moved.
Change-Id: I03ba597b95b4d62b42da112a8efac88d67aa40f9
Signed-off-by: David Brown <davidb@codeaurora.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
No need to have a separate header file containing only register
definitions that are used by a single driver. Fold these into the
gpio driver.
Signed-off-by: David Brown <davidb@codeaurora.org>
The gpiomux.h header contains some SOC ifdefs. However, the API that
is actually used by the GPIO driver only uses two functions that are
general. Move these general definitions into a public header file.
Change-Id: Ia5df8af87dba268225598d56908e523bcfc24ef6
Signed-off-by: David Brown <davidb@codeaurora.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Select the GPIO register configuration at runtime rather than through
idefs.
Change-Id: I02ea0a3d61bc81669f32097c32420f0688552231
Signed-off-by: David Brown <davidb@codeaurora.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Put an SOC prefix on each GPIO register definition, eliminating the
need to have SOC ifdefs around the definitions.
Change-Id: I5a01fd328a89ce1be610847934d6e118f5465e42
Signed-off-by: David Brown <davidb@codeaurora.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
The two GPIO controllers are always mapped to the same virtual address
across all MSM devices. Instead of selecting this at compile time,
determine the physical address at runtime, eliminating yet something
else preventing multiple MSM targets from being compiled into the same
kernel.
Change-Id: I1672219d978ab6243526adeda6badf49472baa27
Signed-off-by: David Brown <davidb@codeaurora.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
The MSM7x25 and MSM7x27 devices are not yet supported in the kernel.
Remove #ifdef-based tables supporting these chips for now.
Change-Id: I4d9f5abc4cc0942ce75a067097b072489493c1b8
Signed-off-by: David Brown <davidb@codeaurora.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k/math-emu: Remove unnecessary code
m68k/math-emu: Remove commented out old code
m68k: Kill warning in setup_arch() when compiling for Sun3
m68k/atari: Prefix GPIO_{IN,OUT} with CODEC_
sparc: iounmap() and *_free_coherent() - Use lookup_resource()
m68k/atari: Reserve some ST-RAM early on for device buffer use
m68k/amiga: Chip RAM - Use lookup_resource()
resources: Add lookup_resource()
sparc: _sparc_find_resource() should check for exact matches
m68k/amiga: Chip RAM - Offset resource end by CHIP_PHYSADDR
m68k/amiga: Chip RAM - Use resource_size() to fix off-by-one error
m68k/amiga: Chip RAM - Change chipavail to an atomic_t
m68k/amiga: Chip RAM - Always allocate from the start of memory
m68k/amiga: Chip RAM - Convert from printk() to pr_*()
m68k/amiga: Chip RAM - Use tabs for indentation
It's been unused for ages, and contains bugs (e.g. incorrect shifts in
lsl64()).
Reported-by: Jonathan Elchison <jelchison@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
These defines are way to generic, and cause conflicts:
drivers/net/wireless/rtlwifi/rtl8192c/../rtl8192ce/reg.h:369:1: warning: "GPIO_IN" redefined
drivers/net/wireless/rtlwifi/rtl8192c/../rtl8192ce/reg.h:370:1: warning: "GPIO_OUT" redefined
drivers/net/wireless/rtlwifi/rtl8192se/reg.h:252:1: warning: "GPIO_IN" redefined
drivers/net/wireless/rtlwifi/rtl8192se/reg.h:253:1: warning: "GPIO_OUT" redefined
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Replace a custom implementation (which doesn't lock the resource tree) by a
call to lookup_resource()
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: David S. Miller <davem@davemloft.net>
Based on an original patch from Michael Schmitz:
Because mem_init() is now called before device init, devices that rely on
ST-RAM may find all ST-RAM already allocated to other users by the time
device init happens. In particular, a large initrd RAM disk may use up
enough of ST-RAM to cause atari_stram_alloc() to resort to
__get_dma_pages() allocation.
In the current state of Atari memory management, all of RAM is marked
DMA capable, so __get_dma_pages() may well return RAM that is not in actual
fact DMA capable. Using this for frame buffer or SCSI DMA buffer causes
subtle failure.
The ST-RAM allocator has been changed to allocate memory from a pool of
reserved ST-RAM of configurable size, set aside on ST-RAM init (i.e.
before mem_init()). As long as this pool is not exhausted, allocation of
real ST-RAM can be guaranteed.
Other changes:
- Replace the custom allocator in the ST-RAM pool by the existing allocator
in the resource subsystem,
- Remove mem_init_done and its hook, as memory init is now done before
device init,
- Remove /proc/stram, as ST-RAM usage now shows up under /proc/iomem, e.g.
005f2000-006f1fff : ST-RAM Pool
005f2000-0063dfff : atafb
0063e000-00641fff : ataflop
00642000-00642fff : SCSI
Signed-off-by: Michael Schmitz <schmitz@debian.org>
[Andreas Schwab <schwab@linux-m68k.org>: Use memparse()]
[Geert: Use the resource subsystem instead of a custom allocator]
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Replace a custom implementation (which doesn't lock the resource tree) by a
call to lookup_resource()
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
The address that's passed to _sparc_find_resource() should always be the
start address of a resource:
- iounmap() passes a page-aligned virtual address, while the original
address was created by adding the in-page offset to the resource's
start address,
- sbus_free_coherent() and pci32_free_coherent() should be passed an
address obtained from sbus_alloc_coherent() resp. pci32_alloc_coherent(),
which is always a resource's start address.
Hence replace the range check by a check for an exact match.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: David S. Miller <davem@davemloft.net>
While the core resource handling code is safe, our global counter must
still be protected against concurrent modifications.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
As of commit 5df1abdbd3 ('m68k/amiga: Fix
"debug=mem"'), "debug=mem" no longer uses amiga_chip_alloc_res(), so we
can remove the hack to prefer memory at the safe end.
This allows to simplify the code and make amiga_chip_alloc() just call
amiga_chip_alloc_res() internally.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
and fix a few formattings:
- resource sizes are now resource_size_t, use %pR to make it future proof,
- use %lu for unsigned long.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (430 commits)
[media] ir-mce_kbd-decoder: include module.h for its facilities
[media] ov5642: include module.h for its facilities
[media] em28xx: Fix DVB-C maxsize for em2884
[media] tda18271c2dd: Fix saw filter configuration for DVB-C @6MHz
[media] v4l: mt9v032: Fix Bayer pattern
[media] V4L: mt9m111: rewrite set_pixfmt
[media] V4L: mt9m111: fix missing return value check mt9m111_reg_clear
[media] V4L: initial driver for ov5642 CMOS sensor
[media] V4L: sh_mobile_ceu_camera: fix Oops when USERPTR mapping fails
[media] V4L: soc-camera: remove soc-camera bus and devices on it
[media] V4L: soc-camera: un-export the soc-camera bus
[media] V4L: sh_mobile_csi2: switch away from using the soc-camera bus notifier
[media] V4L: add media bus configuration subdev operations
[media] V4L: soc-camera: group struct field initialisations together
[media] V4L: soc-camera: remove now unused soc-camera specific PM hooks
[media] V4L: pxa-camera: switch to using standard PM hooks
[media] NetUP Dual DVB-T/C CI RF: force card hardware revision by module param
[media] Don't OOPS if videobuf_dvb_get_frontend return NULL
[media] NetUP Dual DVB-T/C CI RF: load firmware according card revision
[media] omap3isp: Support configurable HS/VS polarities
...
Fix up conflicts:
- arch/arm/mach-omap2/board-rx51-peripherals.c:
cleanup regulator supply definitions in mach-omap2
vs
OMAP3: RX-51: define vdds_csib regulator supply
- drivers/staging/tm6000/tm6000-alsa.c (trivial)
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI: remove printks about disabled bridge windows
PCI: fold pci_calc_resource_flags() into decode_bar()
PCI: treat mem BAR type "11" (reserved) as 32-bit, not 64-bit, BAR
PCI: correct pcie_set_readrq write size
PCI: pciehp: change wait time for valid configuration access
x86/PCI: Preserve existing pci=bfsort whitelist for Dell systems
PCI: ARI is a PCIe v2 feature
x86/PCI: quirks: Use pci_dev->revision
PCI: Make the struct pci_dev * argument of pci_fixup_irqs const.
PCI hotplug: cpqphp: use pci_dev->vendor
PCI hotplug: cpqphp: use pci_dev->subsystem_{vendor|device}
x86/PCI: config space accessor functions should not ignore the segment argument
PCI: Assign values to 'pci_obff_signal_type' enumeration constants
x86/PCI: reduce severity of host bridge window conflict warnings
PCI: enumerate the PCI device only removed out PCI hieratchy of OS when re-scanning PCI
PCI: PCIe AER: add aer_recover_queue
x86/PCI: select direct access mode for mmconfig option
PCI hotplug: Rename is_ejectable which also exists in dock.c
* 'at91/cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc:
at91: add arch specific ioremap support
at91: factorize sram init
at91: move register clocks to soc generic init
at91: move clock subsystem init to soc generic init
at91: use structure to store the current soc
at91: remove AT91_DBGU offset from dbgu register macro
at91: factorize at91 interrupts init to soc
at91: introduce commom AT91_BASE_SYS
* 'next/dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc: (21 commits)
arm/dt: tegra devicetree support
arm/versatile: Add device tree support
dt/irq: add irq_domain_generate_simple() helper
irq: add irq_domain translation infrastructure
dmaengine: imx-sdma: add device tree probe support
dmaengine: imx-sdma: sdma_get_firmware does not need to copy fw_name
dmaengine: imx-sdma: use platform_device_id to identify sdma version
mmc: sdhci-esdhc-imx: add device tree probe support
mmc: sdhci-pltfm: dt device does not pass parent to sdhci_alloc_host
mmc: sdhci-esdhc-imx: get rid of the uses of cpu_is_mx()
mmc: sdhci-esdhc-imx: do not reference platform data after probe
mmc: sdhci-esdhc-imx: extend card_detect and write_protect support for mx5
net/fec: add device tree probe support
net: ibm_newemac: convert it to use of_get_phy_mode
dt/net: add helper function of_get_phy_mode
net/fec: gasket needs to be enabled for some i.mx
serial/imx: add device tree probe support
serial/imx: get rid of the uses of cpu_is_mx1()
arm/dt: Add dtb make rule
arm/dt: Add skeleton dtsi file
...
Russell King