* 'msm-mmc_sdcc' of git://codeaurora.org/quic/kernel/dwalker/linux-msm:
drivers: mmc: msm_sdcc: Add EMBEDDED_SDIO support
mmc: msm_sdcc: Fix issue where clocks could be disabled mid transaction
mmc: msm_sdcc: Fix the dma exec function to use the proper delays
mmc: msm_sdcc: Don't set host->curr.mrq until after we're sure the busclk timer won't fire
mmc: msm_sdcc: Enable busclk idle timer for power savings
mmc: msm_sdcc: Don't disable interrupts while suspending
mmc: msm_sdcc: Fix issue where we might not end a sucessfull request
mmc: msm_sdcc: Featurize busclock power save and disable it by default
mmc: msm_sdcc: Fix bug where busclk expiry timer was not properly disabled
mmc: msm_sdcc: Reduce command timeouts and improve reliability.
mmc: msm_sdcc: Schedule clock disable after probe
mmc: msm_sdcc: Wrap readl/writel calls with appropriate clk delays
mmc: msm_sdcc: Driver clocking/irq improvements
msm: Add 'execute' datamover callback
mmc: msm_sdcc: Snoop SDIO_CCCR_ABORT register
mmc: msm_sdcc: Clean up clock management and add a 10us delay after enabling clocks
Enables basic boot support for the MSM7x30 SURF development
board.
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Gregory Bean <gbean@codeaurora.org>
Signed-off-by: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
The MSM7x30 does not have a separate bank of memory for shared
memory communication with the radio CPU. Set the kernel base
address 2MB in, to use this first 2MB for this purpose.
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Gregory Bean <gbean@codeaurora.org>
Signed-off-by: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
The MSM SOC's DMA controller contains several security domains.
On the MSM7x00, only security domain 3 is accessible to our CPU.
The 7x30, however, uses security domain 2. Fix up the register
definition macros to select this appropriately, based on
configured target.
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Gregory Bean <gbean@codeaurora.org>
Signed-off-by: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
This adds a clock list, and common resource structures
for MSM7x30.
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Gregory Bean <gbean@codeaurora.org>
Signed-off-by: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Add a header describing the io regions for MSM7x30.
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Gregory Bean <gbean@codeaurora.org>
Signed-off-by: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Enable CONFIG_ARCH_QSD8X50. This is the first SOC with the
Scorpion processor.
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Gregory Bean <gbean@codeaurora.org>
Signed-off-by: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Support different RAM base addresses used by Qualcomm SOCs, with
QSD8x50 as the first addtional one.
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Gregory Bean <gbean@codeaurora.org>
Signed-off-by: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
This adds a clock list, and common resource structures
for QSD8x50.
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Gregory Bean <gbean@codeaurora.org>
Signed-off-by: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Add a header describing the io regions for QSD8x50.
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Gregory Bean <gbean@codeaurora.org>
Signed-off-by: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Some SoC need to redefine MSM_DGT_BASE from it's default.
This allows it to be defined in a header to override the
default value.
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
GPIO support for Qualcomm SOCs requires interaction with the
radio (baseband processor). This API allows the different boards
to enable GPIO through the radio processor in a generic way.
Signed-off-by: Gregory Bean <gbean@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Signed-off-by: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
The 'PCOM' method of clock control (commands issued to the radio
CPU) is shared across several (but not all) Qualcomm SOCs.
Generalize this clock mechanism so these other SOCs can be added.
Signed-off-by: Gregory Bean <gbean@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Signed-off-by: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Scorpion-based SOCs from Qualcomm use a different interrupt
controller 'sirc'.
Signed-off-by: Gregory Bean <gbean@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Signed-off-by: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
msm_iomap.h is specific to the MSM7x00 series devices. Generalize
this in preparation to support more devices.
Signed-off-by: Gregory Bean <gbean@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Signed-off-by: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
irqs.h is specific to the MSM7x00 series devices. Generalize
this in preparation to support more devices.
Signed-off-by: Gregory Bean <gbean@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Signed-off-by: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
devices.c is specific to the MSM7x00 series of SOCs. Rename
appropriately in preparation to support more devices.
Signed-off-by: Gregory Bean <gbean@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Signed-off-by: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
Signed-off-by: Stepan Moskovchenko <stepanm@codeaurora.org>
This fixes the following warning,
arch/arm/mach-msm/smd_debug.c:240: warning: initialization from incompatible pointer type
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Without a debug uart selected you get this failure,
arch/arm/mach-msm/board-trout.c:85: error: 'MSM_DEBUG_UART_PHYS' undeclared here (not in a function)
arch/arm/mach-msm/board-trout.c:86: error: 'MSM_DEBUG_UART_BASE' undeclared here (not in a function)
This just removes these lines in that case.
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
This removes the Kconfig menu option. SMD can still be selected
but it's done inside the Kconfig file and not via the menu.
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
When booting up we need to wait for the modem processor to
partially boot. This is because the modem processor does
resource allocation for us. If we don't wait the modem won't
honor our requests and we end up crashing or in an unknown
state. This change just formalizes the waiting process.
Signed-off-by: Daniel Walker <c_dwalke@quicinc.com>
This irq handler isn't used in all cases, so add the proper ifdef. This
eliminates a compiler warning due to the function not getting used.
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
This just removed some unneeded predefines. One needed a whole
function moved down further. The others could just be deleted.
No functional changes.
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
This moves the msm_a2m_int() function into the header, and
does a small macro clean up to be more inline with Linux
norms. No functional changes.
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
"unsigned" translates to "unsigned int", but this value holds an
address. We always want to use unsigned long for addresses since
it will change size to fit the machine.
This just convert the one address holder to unsigned long.
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
This modifies SMD to use either the package v3 or package v4,
but not both. The current code tries to allocate as v4 on all
system which can produce a scary looking error message on boot up,
smem_find(16, 40): wrong size 16424
smd_alloc_channel() cid=02 size=08192 'SMD_RPCCALL'
With this error the code then falls back on the package v3 allocation
method. This method is inefficient because it causes a slow down
on some systems even when the allocation method can be determined
at compile time. It also causes a kernel size increase that effects
all system and is not needed.
This change corrects the allocation to use one method or the other
and not both.
Signed-off-by: Daniel Walker <c_dwalke@quicinc.com>
Forcing the alignment prevents gcc from generating byte reads for word
member variables. Lack of this caused issues when the app processor
modified struct members and the modem saw a partial word write.
Signed-off-by: Dima Zavin <dima@android.com>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Some smd clients may write from multiple threads, in which case it's
not safe to call smd_write without holding a lock. smd_write_atomic()
provides the same functionality as smd_write() but obtains the smd
lock first.
Signed-off-by: Brian Swetland <swetland@google.com>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Don't mark a channel as allocated if we failed to allocate it
(perhaps the modem updated one table but not the other, etc)
Signed-off-by: Brian Swetland <swetland@google.com>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
When we read data out of the sender's fifo, we need to advance the sender's
tail pointer, not the receiver's.
Signed-off-by: Haley Teng <Haley_Teng@htc.com>
Acked-by: Dima Zavin <dima@android.com>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
- QSD8250 has a DSP that speaks SMD, in addition to the modem
- handle a separate list of modem vs dsp channels
- install dsp smd irq handler as necessary
Signed-off-by: Brian Swetland <swetland@google.com>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
- pull debug code into smd_debug.c
- move necessary structures and defines into smd_private.h
- fix some comment formatting, etc
Signed-off-by: Brian Swetland <swetland@google.com>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
The new protocol require writing to two state fields, and reading
several fields.
Signed-off-by: Arve Hjønnevåg <arve@android.com>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
- support both v2 and v1 style smd channels
- support both v2 and v1 smsm shared state
- update smsm state defines and smem item enum
- prep work for dealing with smd to qdsp6
- simplify some smem access to minimize use of smem_alloc() at runtime
Signed-off-by: Brian Swetland <swetland@google.com>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
This code provides the low level interface to the "shared memory
state machine" (smsm), and the virtual serial channels (smd), used
to communicate with the baseband processor. Higher level transports
(rpc, ethernet, AT command channel, etc) ride on top of this.
Signed-off-by: Brian Swetland <swetland@google.com>
Also, convert all SDCC IRQ resources to be named. No longer pass status_irq
in the platform_data
Signed-off-by: Dima Zavin <dima@android.com>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Support independent enable and disable by clients for common
vreg. First enable switches on and last disable switches off.
This change has no check for voltage level so clients
must agree on level for common vreg.
Signed-off-by: Matthew Wilson <mtwilson@quicinc.com>
Fixes the following warning,
arch/arm/mach-msm/acpuclock-arm11.c:138: warning: 'freq_table' defined but not used
when CONFIG_CPU_FREQ_TABLE is not enabled.
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Keep track of the success/failure of the last vreg proc comm
command, and return that on debugfs reads.
Signed-off-by: Steve Muckle <smuckle@quicinc.com>
This adds acpuclock-arm11.c from Google. This provides control
over the cpu frequency for arm11 cpu's.
This has shared authorship between Google, and Qualcomm. Most
of it was written by Mike Chan at Google.
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
ARCH_MSM supports armv7 cpus, so we're pushed the CPU_V6/CPU_V7 selection
down into the arch/arm/mach-msm/Kconfig.
Also update the description to be a bit more accurate.
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Based on a patch from Brent DeGraaf:
"The datamover supports channels which can be shared amongst devices.
As a result, the actual data transfer may occur some time after the
request is queued up. Some devices such as mmc host controllers
will timeout if a command is issued too far in advance of the actual
transfer, so if dma to other devices on the same channel is already
in progress or queued up, the added delay can cause pending transfers
to fail before they start. This change extends the api to allow a
user callback to be invoked just before the actual transfer takes
place, thus allowing actions directly associated with the dma
transfer, such as device commands, to be invoked with precise timing.
Without this mechanism, there is no way for a driver to realize
this timing. Also adds a user pointer to the command structure for use
by the caller to reference information that may be needed by the
callback routine for proper identification and processing associated
with that specific request. This change is necessary to fix problems
associated with excessive command timeouts and race conditions in the
mmc driver."
This patch also fixes all the callers of msm_dmov_enqueue_cmd() to
ensure their callback function is NULL.
Signed-off-by: San Mehat <san@google.com>
Cc: Brent DeGraaf <bdegraaf@quicinc.com>
Cc: Brian Swetland <swetland@google.com>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
This allows the procfs vmallocinfo file to show who created the ioremap
regions. Note: __builtin_return_address(0) doesn't do what's expected
if its used in an inline function, so we leave __arm_ioremap callers
in such places alone.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Otherwise more complicated uart configuration won't be possible.
We can use r1 for tmp register for both head.S and debug.S.
NOTE: This patch depends on another patch to add the the tmp register
into all debug-macro.S files. That can be done with:
$ sed -i -e "s/addruart,rx|addruart, rx/addruart, rx, tmp/"
arch/arm/*/include/*/debug-macro.S
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add missing include for msm_sdcc compilation, and remove pwrsink
support that is not mainline, yet.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
[dwalker@codeaurora.org : fixed indent in mmc.h]
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Add memory map to HTC Dream, so that boot can proceed further.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
This is just enough to get the device booting and serial console
working. Sufficient for debugging further MSM7k/Dream Support.
This will support HTC Dream / T-Mobile G1 / Android ADP1 (which
are all the same hardware, known as "trout" to the ARM machine
database).
Signed-off-by: Brian Swetland <swetland@google.com>
Reviewed-by: GeunSik Lim <geunsik.lim@samsung.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Provides options to select one of the three "lowspeed" UARTs
on MSM7k SoCs for DEBUG_LL output from the zImage decompressor
and kernel.
Signed-off-by: Brian Swetland <swetland@google.com>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Pass clocksource pointer to the read() callback for clocksources. This
allows us to share the callback between multiple instances.
[hugh@veritas.com: fix powerpc build of clocksource pass clocksource mods]
[akpm@linux-foundation.org: cleanup]
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Acked-by: John Stultz <johnstul@us.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
OMAP wishes to pass state to the boot loader upon reboot in order to
instruct it whether to wait for USB-based reflashing or not. There is
already a facility to do this via the reboot() syscall, except we ignore
the string passed to machine_restart().
This patch fixes things to pass this string to arch_reset(). This means
that we keep the reboot mode limited to telling the kernel _how_ to
perform the reboot which should be independent of what we request the
boot loader to do.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
arch/arm/mach-msm/board-halibut.c:45: error: implicit declaration of function 'MSM_GPIO_TO_INT'
arch/arm/mach-msm/board-halibut.c:45: error: initializer element is not constant
arch/arm/mach-msm/board-halibut.c:45: error: (near initialization for 'smc91x_resources[1].start')
arch/arm/mach-msm/board-halibut.c:46: error: initializer element is not constant
arch/arm/mach-msm/board-halibut.c:46: error: (near initialization for 'smc91x_resources[1].end')
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
arch/arm/mach-at91/at91cap9.c:337: error: 'NR_AIC_IRQS' undeclared here (not in a function)
arch/arm/mach-at91/at91rm9200.c:301: error: 'NR_AIC_IRQS' undeclared here (not in a function)
arch/arm/mach-at91/at91sam9260.c:351: error: 'NR_AIC_IRQS' undeclared here (not in a function)
arch/arm/mach-at91/at91sam9261.c:287: error: 'NR_AIC_IRQS' undeclared here (not in a function)
arch/arm/mach-at91/at91sam9263.c:312: error: 'NR_AIC_IRQS' undeclared here (not in a function)
arch/arm/mach-at91/at91sam9rl.c:304: error: 'NR_AIC_IRQS' undeclared here (not in a function)
arch/arm/mach-h720x/h7202-eval.c:38: error: implicit declaration of function 'IRQ_CHAINED_GPIOB'
arch/arm/mach-ks8695/devices.c:46: error: 'KS8695_IRQ_WAN_RX_STATUS' undeclared here (not in a function)
arch/arm/mach-msm/devices.c:28: error: 'INT_UART1' undeclared here (not in a function)
arch/arm/mach-mx2/devices.c:233: error: 'MXC_GPIO_IRQ_START' undeclared here (not in a function)
arch/arm/mach-mx3/devices.c:128: error: 'MXC_GPIO_IRQ_START' undeclared here (not in a function)
arch/arm/mach-omap1/mcbsp.c:140: error: 'INT_730_McBSP1RX' undeclared here (not in a function)
arch/arm/mach-omap1/mcbsp.c:165: error: 'INT_McBSP1RX' undeclared here (not in a function)
arch/arm/mach-omap1/mcbsp.c:200: error: 'INT_McBSP1RX' undeclared here (not in a function)
arch/arm/mach-omap2/board-apollon.c:286: error: implicit declaration of function 'omap_set_gpio_direction'
arch/arm/mach-omap2/mcbsp.c:154: error: 'INT_24XX_MCBSP1_IRQ_RX' undeclared here (not in a function)
arch/arm/mach-omap2/mcbsp.c:181: error: 'INT_24XX_MCBSP1_IRQ_RX' undeclared here (not in a function)
arch/arm/mach-pxa/e350.c:36: error: 'IRQ_BOARD_START' undeclared here (not in a function)
arch/arm/plat-s3c/dev-i2c0.c:32: error: 'IRQ_IIC' undeclared here (not in a function)
...
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'cpus4096-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (66 commits)
x86: export vector_used_by_percpu_irq
x86: use logical apicid in x2apic_cluster's x2apic_cpu_mask_to_apicid_and()
sched: nominate preferred wakeup cpu, fix
x86: fix lguest used_vectors breakage, -v2
x86: fix warning in arch/x86/kernel/io_apic.c
sched: fix warning in kernel/sched.c
sched: move test_sd_parent() to an SMP section of sched.h
sched: add SD_BALANCE_NEWIDLE at MC and CPU level for sched_mc>0
sched: activate active load balancing in new idle cpus
sched: bias task wakeups to preferred semi-idle packages
sched: nominate preferred wakeup cpu
sched: favour lower logical cpu number for sched_mc balance
sched: framework for sched_mc/smt_power_savings=N
sched: convert BALANCE_FOR_xx_POWER to inline functions
x86: use possible_cpus=NUM to extend the possible cpus allowed
x86: fix cpu_mask_to_apicid_and to include cpu_online_mask
x86: update io_apic.c to the new cpumask code
x86: Introduce topology_core_cpumask()/topology_thread_cpumask()
x86: xen: use smp_call_function_many()
x86: use work_on_cpu in x86/kernel/cpu/mcheck/mce_amd_64.c
...
Fixed up trivial conflict in kernel/time/tick-sched.c manually
Impact: change calling convention of existing clock_event APIs
struct clock_event_timer's cpumask field gets changed to take pointer,
as does the ->broadcast function.
Another single-patch change. For safety, we BUG_ON() in
clockevents_register_device() if it's not set.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Ingo Molnar <mingo@elte.hu>
As Al did for Versatile in 2ad4f86b60,
add a typesafe __io implementation for platforms to use. Convert
platforms to use this new simple typesafe implementation.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Let's provide an overridable default instead of having every machine
class define __virt_to_bus and __bus_to_virt to the same thing. What
most platforms are using is bus_addr == phys_addr so such is the default.
One exception is ebsa110 which has no DMA what so ever, so the actual
definition is not important except only for proper compilation. Also
added a comment about the special footbridge bus translation.
Let's also remove comments alluding to set_dma_addr which is not
(and should not) be commonly used.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The baseband cpu owns the pmic, so voltage regulator control is only
available via a relatively limited interface through the proc_comm
transport.
Signed-off-by: Brian Swetland <swetland@google.com>
San:
- Propagate DM errors to the originator of the request.
- Implement msm_dmov_stop_cmd()
- Add return value to init code
- Modify msm_dmov_stop_cmd() to support ungraceful flushing
Arve:
- Disable datamover interrupt when not in use.
We turn off the interrrupt to allow power collapse from idle.
Signed-off-by: San Mehat <san@android.com>
Signed-off-by: Arve Hjønnevåg <arve@android.com>
Signed-off-by: Brian Swetland <swetland@google.com>
- Add some more peripherals (sdcc, etc) to the iomap.
- Remove virtual base addresses for devices that we should be passing
physical addresses to drivers via resources and ioremap()ing.
- don't try to use uarts for ll debug once the mmu is enabled due to
problems with the peripheral window
- make base addresses void __iomem * and fixup irq.c and timer.c
- Remove common.c and bring in devices.c/devices.h similar to
the PXA architecture.
Signed-off-by: Brian Swetland <swetland@google.com>
The proc_comm protocol is the lowest level protocol available for
communicating with the modem core. It provides access to clock and
power control, among other things, and is safe for use from atomic
contexts, unlike the higher level SMD and RPC transports.
Signed-off-by: Brian Swetland <swetland@google.com>
The MSM architecture covers a wider family of chips than just the MSM7X00A.
Move to a more generic name, in perparation for supporting the specific
SoC variants as sub-architectures (ARCH_MSM7X01A, ARCH_MSM722X, etc). This
gives us ARCH_MSM for the (many) common peripherals.
This also removes the unused/obsolete config item MSM7X00A_IDLE.
Signed-off-by: Brian Swetland <swetland@google.com>
Remove includes of asm/hardware.h in addition to asm/arch/hardware.h.
Then, since asm/hardware.h only exists to include asm/arch/hardware.h,
update everything to directly include asm/arch/hardware.h and remove
asm/hardware.h.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for the Qualcomm MSM7200A eval board.
Common devices are defined in common.c, to avoid excessive
cut'n'pasting them into other board files.
Signed-off-by: Brian Swetland <swetland@google.com>
- core header files for arch-msm
- Kconfig and Makefiles to enable ARCH_MSM7X00A builds
- MSM7X00A specific arch_idle
- peripheral iomap and irq number definitions
Signed-off-by: Brian Swetland <swetland@google.com>