Move host claim/release into mmc_blk_issue_rq.
(This is helpful so that selecting partition only has to happen
in one place for these commands.)
Signed-off-by: Andrei Warkentin <andreiw@motorola.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
CMD6 is an R1B-type command, where DAT is used as busy. Depending
on register written using CMD6, timeout value can be different
as per spec.
Signed-off-by: Andrei Warkentin <andreiw@motorola.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
ERASE command needs R1B response, so fix R1B-type command
handling for SDHCI controller. For non-DAT commands using a busy
response, the cmd->cmd_timeout_ms (in ms) field is used for timeout
calculations.
Based on patch by Chuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: Andrei Warkentin <andreiw@motorola.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Renames erase_timeout to cmd_timeout_ms inside struct mmc_command.
First step to making host honor timeouts for non-data-transfer
commands. Cleans up erase timeout code.
Signed-off-by: Andrei Warkentin <andreiw@motorola.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The current mechanism is SDIO-only. This allows us to create
function-specific quirks, without creating messy Kconfig dependencies,
or polluting core/ with function-specific code.
Signed-off-by: Andrei Warkentin <andreiw@motorola.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
led_trigger_register_simple() allocates memory which must not be leaked
in the error-path of mmc_add_host. Move it past the only error-check in
the function.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch fixes 21 errors and 6 warnings reported by checkpatch.pl.
Signed-off-by: Ameya Palande <2ameya@gmail.com>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
The wl12xx device supports disconnecting the pull-up resistor on
CD/DAT[3] (pin 1) of the card.
Tell SDIO core to disconnect that resistor during card init,
since we don't need it at that point (and anyway all
hosts shall provide pull-up resistors on all data lines DAT[3:0]
as described in section 6 of the SD physical specification).
As a result, this may save some power, but it's also generally healthy
since it prevents both ends from pulling up that pin, which
results in undesirable asymmetric physical bus.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
006ebd5d introduced sdio_disable_cd(), which disconnects the pull-up
resistor on CD/DAT[3] (pin 1) of the card.
Make it possible to start using sdio_disable_cd() by introducing
MMC_QUIRK_DISABLE_CD.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Tell SDIO core to ignore the standard SDIO function interface
codes indicated by the wl1271. This is required because the
wl1271 erroneously indicates its first function as a standard
Bluetooth SDIO interface, and that drives btsdio mad.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Introduce MMC_QUIRK_NONSTD_FUNC_IF to ignore the "SDIO Standard Function
interface code" as indicated by the card's FBR, and instead treat all
functions as non-standard interfaces.
This is required to prevent standard drivers from facing
errors when trying to communicate with SDIO cards that erroneously
indicate standard function interface codes.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
6b5eda36 followed SDIO spec part E1 section 8, which states that
in case SDIO interrupts are being used to wake up a suspended host,
then it is required to switch to 1-bit mode before stopping the clock.
Before switching to 1-bit mode (or back to 4-bit mode on resume),
make sure that SDIO interrupts are really being used to wake the host.
This is helpful for devices which have an external irq line (e.g.
wl1271), and do not use SDIO interrupts to wake up the host.
In this case, switching to 1-bit mode (and back to 4-bit mode on resume)
is not necessary.
Reported-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
mmc_card_is_powered_resumed is a mouthful; instead, simply use
mmc_card_keep_power, which also better explains the purpose of
the macro.
Employ mmc_card_keep_power() where possible.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Allows reliable writes to be used for MMC writes. Reliable writes are used
to service write REQ_FUA/REQ_META requests. Handles both the legacy and
the enhanced reliable write support in MMC cards.
Signed-off-by: Andrei Warkentin <andreiw@motorola.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
This config option is used to decide whether tegra sdhci support
should be build into the sdhci-platform module. So setting it 'm'
is nonsense, since we can't build part of an module as a module.
The effect for 'm' will probably be the same as for 'n'.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Enable fast bcm4329 WIFI suspend/resume on Tegra2 board.
This patch allows the mach-tegra support to tell the tegra MMC host
controller to NOT turn off power for the MMC controller the WIFI part
lives behind. Thus bcm4329 firmware doesn't need to be reloaded.
Signed-off-by: Venkat Rao <vrao@broadcom.com>
Tested-by: Grant Grundler <grundler@chromium.org>
Reviewed-by: Olof Johansson <olof@lixom.net>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Chris Ball <cjb@laptop.org>
There is no need to disable irq's when using the sg_copy_*_buffer()
functions because those functions do that already. There are also
no races for the mm_queue struct here that would require the irq's
to be disabled before calling sg_copy_*_buffer().
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
uBoot sometimes leaves eMMC pointing to the private boot partition.
Ensure we always start looking at the user partition.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Bruce Clemens <bpclemens@marvell.com>
Signed-off-by: Mark F. Brown <markb@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/brodo/pcmcia-2.6:
pcmcia: Make struct pcmcia_device_id const, sound drivers edition
staging: pcmcia: Convert pcmcia_device_id declarations to const
pcmcia: Convert pcmcia_device_id declarations to const
pcmcia: Make declaration and uses of struct pcmcia_device_id const
pcmcia/sa1100: put sa11x0_pcmcia_hw_init[] to .devinit.data
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (137 commits)
ARM: bcmring: convert to use sp804 clockevents
ARM: bcmring: convert to sp804 clocksource
ARM: 6912/1: bcmring: Add clkdev table in init_early
clockevents: ARM sp804: obtain sp804 timer rate via clks
clockevents: ARM sp804: allow clockevent name to be specified
clocksource: ARM sp804: obtain sp804 timer rate via clks
clocksource: ARM sp804: allow clocksource name to be specified
clocksource: convert OMAP1 to 32-bit down counting clocksource
clocksource: convert MXS timrotv2 to 32-bit down counting clocksource
clocksource: convert SPEAr platforms 16-bit up counting clocksource
clocksource: convert Integrator/AP 16-bit down counting clocksource
clocksource: convert W90x900 24-bit down counting clocksource
clocksource: convert ARM 32-bit down counting clocksources
clocksource: convert ARM 32-bit up counting clocksources
clocksource: add common mmio clocksource
ARM: update sa1100 to reflect PXA updates
ARM: omap1: convert to using readl/writel instead of volatile struct
ARM: omap1: delete useless interrupt handler
ARM: s5p: consolidate selection of timer register
ARM: 6939/1: fix missing 'cpu_relax()' declaration
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits)
b43: fix comment typo reqest -> request
Haavard Skinnemoen has left Atmel
cris: typo in mach-fs Makefile
Kconfig: fix copy/paste-ism for dell-wmi-aio driver
doc: timers-howto: fix a typo ("unsgined")
perf: Only include annotate.h once in tools/perf/util/ui/browsers/annotate.c
md, raid5: Fix spelling error in comment ('Ofcourse' --> 'Of course').
treewide: fix a few typos in comments
regulator: change debug statement be consistent with the style of the rest
Revert "arm: mach-u300/gpio: Fix mem_region resource size miscalculations"
audit: acquire creds selectively to reduce atomic op overhead
rtlwifi: don't touch with treewide double semicolon removal
treewide: cleanup continuations and remove logging message whitespace
ath9k_hw: don't touch with treewide double semicolon removal
include/linux/leds-regulator.h: fix syntax in example code
tty: fix typo in descripton of tty_termios_encode_baud_rate
xtensa: remove obsolete BKL kernel option from defconfig
m68k: fix comment typo 'occcured'
arch:Kconfig.locks Remove unused config option.
treewide: remove extra semicolons
...
Commit b826291c, "drivercore/dt: add a match table pointer to struct
device" added an of_match pointer to struct device to cache the
of_match_table entry discovered at driver match time. This was unsafe
because matching is not an atomic operation with probing a driver. If
two or more drivers are attempted to be matched to a driver at the
same time, then the cached matching entry pointer could get
overwritten.
This patch reverts the of_match cache pointer and reworks all users to
call of_match_device() directly instead.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This fixes a regression on high clock speeds with the MMCI on
ux500. We need to make sure we derive the passthru clock on the
falling edge of the incoming clock if it shall work at high
frequencies, and on the ux500's there is a special bit for this.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The mmci.h header contained a few registers not clearly marked
as ST Micro only, rectify this and remove the HWFC magic in the
process. The idea is to make the mmci.h header file more ordered
so other vendors with PL180 derivates can see where to put in
their custom register defines.
Includes portions of an earlier patch from Sebastian Rasmussen.
Acked-by: Sebastian Rasmussen <sebastian.rasmussen@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Saves about 50KB of data.
Old/new size of all objects:
text data bss dec hex filename
563015 80096 130684 773795 bcea3 (TOTALS)
610916 32256 130632 773804 bceac (TOTALS)
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Kurt Van Dijck <kurt.van.dijck@eia.be> (for drivers/net/can/softing/softing_cs.c)
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
It seems that under certain circumstances the sdhci_tasklet_finish()
call can be entered with mrq set to NULL, causing the system to crash
with a NULL pointer de-reference.
Seen on S3C6410 system. Based on a patch by Dimitris Papastamos.
Reported-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Cc: <stable@kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
It seems that under certain circumstances that the sdhci_tasklet_finish()
call can be entered with mrq->cmd set to NULL, causing the system to crash
with a NULL pointer de-reference.
Unable to handle kernel NULL pointer dereference at virtual address 00000000
PC is at sdhci_tasklet_finish+0x34/0xe8
LR is at sdhci_tasklet_finish+0x24/0xe8
Seen on S3C6410 system.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: <stable@kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The aggressive clock gating for TMIO MMC patch has broken switching
interface power on, using MFD or platform callbacks. Restore the
ios->power_mode == MMC_POWER_UP && ios->clock == 0 case handling.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Currently there is a race in the MMC core between a card-detect
rescan work and the clock-gating work, scheduled from a command
completion. Fix it by removing the dedicated clock-gating mutex
and using the MMC standard locking mechanism instead.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Simon Horman <horms@verge.net.au>
Cc: Magnus Damm <damm@opensource.se>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: <stable@kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Either OMAP_MMC_STAT_CARD_ERR or OMAP_MMC_STAT_END_OF_CMD might fire
if there is no host->cmd pointer.
Check for a valid host->cmd pointer before calling mmc_omap_cmd_done().
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Fixes a cosmetic bug that affects printk() for SD-combo cards.
Reported-by: Prashanth Bhat <prashanth.bhat@manipal.net>
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Chris Ball <cjb@laptop.org>
If pci_ioremap_bar() fails during probe, we "goto release;" and free the
host, but then we return 0 -- which tells sdhci_pci_probe() that the probe
succeeded. Since we think the probe succeeded, when we unload sdhci we'll
go to sdhci_pci_remove_slot() and it will try to dereference slot->host,
which is now NULL because we freed it in the error path earlier.
The patch simply sets ret appropriately, so that sdhci_pci_probe() will
detect the failure immediately and bail out.
Signed-off-by: Chris Ball <cjb@laptop.org>
Cc: <stable@kernel.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (26 commits)
mmc: SDHI should depend on SUPERH || ARCH_SHMOBILE
mmc: tmio_mmc: Move some defines into a shared header
mmc: tmio: support aggressive clock gating
mmc: tmio: fix power-mode interpretation
mmc: tmio: remove work-around for unmasked SDIO interrupts
sh: fix SDHI IO address-range
ARM: mach-shmobile: fix SDHI IO address-range
mmc: tmio: only access registers above 0xff, if available
mfd: remove now redundant sh_mobile_sdhi.h header
sh: convert boards to use linux/mmc/sh_mobile_sdhi.h
ARM: mach-shmobile: convert boards to use linux/mmc/sh_mobile_sdhi.h
mmc: tmio: convert the SDHI MMC driver from MFD to a platform driver
sh: ecovec: use the CONFIG_MMC_TMIO symbols instead of MFD
mmc: tmio: split core functionality, DMA and MFD glue
mmc: tmio: use PIO for short transfers
mmc: tmio-mmc: Improve DMA stability on sh-mobile
mmc: fix mmc_app_send_scr() for dma transfer
mmc: sdhci-esdhc: enable esdhc on imx53
mmc: sdhci-esdhc: use writel/readl as general APIs
mmc: sdhci: add the abort CMDTYPE bits definition
...
Fix build breakage on platforms, not providing readsw and writesw
functions, e.g., on x86(_64).
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Also add TMIO_BBS.
This allows these defines to also be used by zboot.
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The power-mode sequence on MMC is MMC_POWER_OFF -> MMC_POWER_UP ->
MMC_POWER_ON and not MMC_POWER_ON -> MMC_POWER_UP, as the driver currently
is implying.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
SDIO IRQs got unmasked on sh-mobile while writing to the
CTL_CLK_AND_WAIT_CTL register, because that register at address 0x138
is not implemented on those SoCs and writes to it overwrite the
register at address 0x38: CTL_SDIO_IRQ_MASK. Previous patches
eliminated access to register above 0xff on sh-mobile, so that this
work-around isn't needed anymore.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Not all tmio implementations have registers above oxff. Accessing
them on thise platforms is dangerous. In some cases it leads to
address wrapping to addresses below 0x100, which corrupts random
unrelated registers.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
On sh-mobile platforms the SDHI driver was using the tmio_mmc SD/SDIO
MFD cell driver. Now that the tmio_mmc driver has been split into a
core and a separate MFD glue, we can support SDHI natively without the
need to emulate an MFD controller. This also allows to support systems
with an on-SoC SDHI controller and a separate MFD with a TMIO core.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
TMIO MMC chips contain an SD / SDIO IP core from Panasonic, similar to
the one, used in MN5774 and other MN57xx controllers. These IP cores are
included in many multifunction devices, in sh-mobile chips from Renesas,
in the latter case they can also use DMA. Some sh-mobile implementations
also have some other specialities, that MFD-based solutions don't have.
This makes supporting all these features in a monolithic driver inconveniet
and error-prone. This patch splits the driver into 3 parts: the core,
the MFD glue and the DMA support. In case of a modular build, two modules
will be built: mmc_tmio_core and mmc_tmio.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch allows transferring of some requests in PIO and some in DMA
mode and defaults to using DMA only for transfers longer than 8 bytes.
This is especially useful with SDIO, which can have lots of 2- and 4-byte
transfers, creating unnecessary high overhead, when executed in DMA.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
On some SDHI tmio implementations the order of DMA and command completion
interrupts swaps, which leads to malfunction. This patch postpones
DMA activation until the MMC command completion IRQ time.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch is based on the commit "af51715079e7fb6b290e1881d63d815dc4de5011":
* Bugfix to that mmc_send_cxd_data() code: dma-to-stack is
unsafe/nonportable, so kmalloc a bounce buffer instead.
The driver may invalidate the mmc_card->csd when host driver uses dma.
So this subroutine also needs a kmalloc buffer.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Fix the NO INT in the Multi-BLK IO in SD/MMC, and Multi-BLK read in
SDIO on imx53.
The CMDTYPE of the CMD register (offset 0xE) should be set to "11"
when the STOP CMD12 is issued on imx53 to abort one open ended
multi-blk IO. Otherwise the TC INT wouldn't be generated.
In exact block transfer, the controller doesn't complete the
operations automatically as required at the end of the transfer
and remains on hold if the abort command is not sent on imx53.
As a result, the TC flag is not asserted and SW receives timeout
exception. Set bit1 of Vendor Spec register to fix it.
Signed-off-by: Richard Zhu <Hong-Xing.Zhu@freescale.com>
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add one flag to indicate the GPIO CD/WP is enabled or not
on imx platforms, and reuse the writel/readl as the general
APIs for imx SOCs.
Signed-off-by: Richard Zhu <Hong-Xing.Zhu@freescale.com>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add the abort CMDTYPE bits definition of command register (offset 0xE)
Signed-off-by: Richard Zhu <Hong-Xing.Zhu@freescale.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
sdhci-esdhc-imx does not need SDHCI_QUIRK_NO_CARD_NO_RESET.
Make it OF-specific.
Signed-off-by: Richard Zhu <Hong-Xing.Zhu@freescale.com>
Tested-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Since these are the headers that provide irq_of_parse_and_map()
and NO_IRQ.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Chris Ball <cjb@laptop.org>
New IO FPGA implementation for Versatile Express boards contain
MMCI (PL180) cell with FIFO extended to 128 words (512 bytes).
Matt Waddel reports that this patch improves MMC performance on
his vexpress system, and also fixes "mmcblk0: error -5 transferring
data" errors.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Tested-by: Matt Waddel <matt.waddel@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch uses the fixed burst bit when using an internal DMA controller.
I found increased performance with IDMAC when this bit is set.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The SDHCI driver uses PCI_CLASS_REVISION instead of PCI_REVISION_ID, so
it was not converted by commit 44c10138fd
(PCI: Change all drivers to use pci_device->revision). The newer VIA
driver has similar code too. This patch converts both drivers to use
the 'revision' field of 'struct pci_dev'.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: Harald Welte <HaraldWelte@viatech.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Fixes:
drivers/mmc/card/mmc_test.c: In function ‘mmc_test_seq_perf’:
drivers/mmc/card/mmc_test.c:1878:28: warning: variable ‘ts’ set but not
used [-Wunused-but-set-variable]
There's no reason to be calling timespec_sub() here, because
mmc_test_print_avg_rate() is going to do that itself.
Signed-off-by: Chris Ball <cjb@laptop.org>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
* 'for-2.6.39/core' of git://git.kernel.dk/linux-2.6-block: (65 commits)
Documentation/iostats.txt: bit-size reference etc.
cfq-iosched: removing unnecessary think time checking
cfq-iosched: Don't clear queue stats when preempt.
blk-throttle: Reset group slice when limits are changed
blk-cgroup: Only give unaccounted_time under debug
cfq-iosched: Don't set active queue in preempt
block: fix non-atomic access to genhd inflight structures
block: attempt to merge with existing requests on plug flush
block: NULL dereference on error path in __blkdev_get()
cfq-iosched: Don't update group weights when on service tree
fs: assign sb->s_bdi to default_backing_dev_info if the bdi is going away
block: Require subsystems to explicitly allocate bio_set integrity mempool
jbd2: finish conversion from WRITE_SYNC_PLUG to WRITE_SYNC and explicit plugging
jbd: finish conversion from WRITE_SYNC_PLUG to WRITE_SYNC and explicit plugging
fs: make fsync_buffers_list() plug
mm: make generic_writepages() use plugging
blk-cgroup: Add unaccounted time to timeslice_used.
block: fixup plugging stubs for !CONFIG_BLOCK
block: remove obsolete comments for blkdev_issue_zeroout.
blktrace: Use rq->cmd_flags directly in blk_add_trace_rq.
...
Fix up conflicts in fs/{aio.c,super.c}
This silences warnings such as
drivers/video/tmiofb.c: In function 'tmiofb_hw_init':
drivers/video/tmiofb.c:270: warning: initialization discards qualifiers from pointer target type
These were added by me in commit 2a79bb1d.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Use mfd_data for passing information from mfd drivers to mfd
clients. The mfd_cell's driver_data field is being phased out.
Clients that were using driver_data now access .mfd_data
via mfd_get_data(). This changes tmio-mmc only; mfd drivers with
other cells are not modified.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
No need to explicitly set the cell's platform_data/data_size.
Modify clients to use mfd_get_cell helper function instead of
accessing platform_data directly.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (53 commits)
mmc: dw_mmc: support mmc power control with regulator
mmc: dw_mmc: fix suspend/resume operation
mmc: dw_mmc: add quirks for unreliable card detect, and capabilities
mmc: tmio: fix address in kunmap_atomic() calls
mmc: core: reset card voltage after power off
mmc: core: export function mmc_do_release_host()
mmc: sdio: remember new card RCA when redetecting card
mmc: dw_mmc: Remove set-but-unused variable.
mmc: sdhci-esdhc-imx: add card detect on custom GPIO for mx25/35
mmc: sdhci-esdhc: broken card detection is not a default quirk
mmc: sdhci-esdhc-imx: add write protect on custom GPIO on mx25/35
mmc: msm_sdcc: remove needless cache flush after dma_unmap_sg()
mmc: sh_mmcif: support aggressive clock gating
mmc: check if mmc cards < 2GB do sector addressing
mmc: core: comment on why sdio_reset is done at init time
mmc: dw_mmc: support DDR mode
mmc: via-sdmmc: Remove set-but-unused variable.
mmc: cb710: Return err value in cb710_wait_while_busy()
mmc: sdhci-pci: Remove set-but-unused variable.
mmc: mxs-mmc: add mmc host driver for i.MX23/28
...
* 'spi/next' of git://git.secretlab.ca/git/linux-2.6: (34 commits)
spi/dw_spi: move dw_spi.h into drivers/spi
spi/dw_spi: Fix missing header
gpio/langwell: Clear edge bit before handling
gpio/langwell: Simplify demux loop
gpio/langwell: Convert irq name space
gpio/langwell: Fix broken irq_eoi change.
gpio; Make Intel chipset gpio drivers depend on x86
gpio/cs5535-gpio: Fix section mismatch
spi/rtc-{ds1390,ds3234,m41t94}: Use spi_get_drvdata() for SPI devices
spi/davinci: Support DMA transfers larger than 65535 words
spi/davinci: Use correct length parameter to dma_map_single calls
gpio: Use __devexit at necessary places
gpio: add MODULE_DEVICE_TABLE to pch_gpio and ml_ioh_gpio
gpio/mcp23s08: support mcp23s17 variant
of_mmc_spi: add card detect irq support
spi/omap_mcspi: catch xfers of non-multiple SPI word size
spi/omap_mcspi: Off-by-one error in finding the right divisor
gpio/pca953x: Fix wrong pointer type
spi/pl022: rid dangling labels
spi: add support for SuperH SPI
...
* 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (258 commits)
omap: zoom: host should not pull up wl1271's irq line
arm: plat-omap: iommu: fix request_mem_region() error path
OMAP2+: Common CPU DIE ID reading code reads wrong registers for OMAP4430
omap4: mux: Remove duplicate mux modes
omap: iovmm: don't check 'da' to set IOVMF_DA_FIXED flag
omap: iovmm: disallow mapping NULL address when IOVMF_DA_ANON is set
omap2+: mux: Fix compile when CONFIG_OMAP_MUX is not selected
omap4: board-omap4panda: Initialise the serial pads
omap3: board-3430sdp: Initialise the serial pads
omap4: board-4430sdp: Initialise the serial pads
omap2+: mux: Add macro for configuring static with omap_hwmod_mux_init
omap2+: mux: Remove the use of IDLE flag
omap2+: Add separate list for dynamic pads to mux
perf: add OMAP support for the new power events
OMAP4: Add IVA OPP enteries.
OMAP4: Update Voltage Rail Values for MPU, IVA and CORE
OMAP4: Enable 800 MHz and 1 GHz MPU-OPP
OMAP3+: OPP: Replace voltage values with Macros
OMAP3: wdtimer: Fix CORE idle transition
Watchdog: omap_wdt: add fine grain runtime-pm
...
Fix up various conflicts in
- arch/arm/mach-omap2/board-omap3evm.c
- arch/arm/mach-omap2/clock3xxx_data.c
- arch/arm/mach-omap2/usb-musb.c
- arch/arm/plat-omap/include/plat/usb.h
- drivers/usb/musb/musb_core.h
* 'for-linus' of git://codeaurora.org/quic/kernel/davidb/linux-msm: (46 commits)
msm: scm: Check for interruption immediately
msm: scm: Fix improper register assignment
msm: scm: Mark inline asm as volatile
msm: iommu: Enable HTW L2 redirection on MSM8960
msm: iommu: Don't read from write-only registers
msm: iommu: Remove dependency on IDR
msm: iommu: Use ASID tagging instead of VMID tagging
msm: iommu: Rework clock logic and add IOMMU bus clock control
msm: iommu: Clock control for the IOMMU driver
msm: mdp: Set the correct pack pattern for XRGB/ARGB
msm_fb: Fix framebuffer console
msm: mdp: Add support for RGBX 8888 image format.
video: msmfb: Put the partial update magic value into the fix_screen struct.
msm: clock: Migrate to clkdev
msm: clock: Remove references to clk_ops_pcom
msm: headsmp.S: Fix section mismatch
msm: Use explicit GPLv2 licenses
msm: iommu: Enable IOMMU support for MSM8960
msm: iommu: Generalize platform data for multiple targets
msm: iommu: Create a Kconfig item for the IOMMU driver
...
* 'defcfg' of master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: 6647/1: add Versatile Express defconfig
ARM: 6644/1: mach-ux500: update the U8500 defconfig
* 'drivers' of master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: 6764/1: pl011: factor out FIFO to TTY code
ARM: 6763/1: pl011: add optional RX DMA to PL011 v2
ARM: 6758/1: amba: support pm ops
ARM: amba: make amba_driver id_table const
ARM: amba: make internal ID table handling const
ARM: amba: make probe() functions take const id tables
ARM: 6662/1: amba: make amba_bustype non-static
ARM: mmci: add dmaengine-based DMA support
ARM: mmci: no need for separate host->data_xfered
ARM: mmci: avoid unnecessary switch to data available PIO interrupts
ARM: mmci: no need to call flush_dcache_page() with sg_miter API
ARM: mmci: avoid reporting too many completed bytes on fifo overrun
ALSA: AACI: make fifo variables more explanitory
ALSA: AACI: no need to call snd_pcm_period_elapsed() for each period
ALSA: AACI: use snd_pcm_lib_period_bytes()
ALSA: AACI: clean up AACI announcement printk
ALSA: AACI: fix channel mask selection
ALSA: AACI: fix number of channels for record
ALSA: AACI: fix multiple IRQ claiming
* 'cyberpro-next' of master.kernel.org:/home/rmk/linux-2.6-arm:
VIDEO: cyberpro: remove unused cyber2000fb_get_fb_var()
VIDEO: cyberpro: remove useless function extreg pointers
VIDEO: cyberpro: update handling of device structures
VIDEO: cyberpro: add support for video capture I2C
VIDEO: cyberpro: make 'reg_b0_lock' always present
VIDEO: cyberpro: add I2C support
VIDEO: cyberpro: select lowest multipler/divisor for PLL
This patch adds support for power regulators.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch is related to re-init processing on suspend/resume.
When card is resuming, some register is reset. If card is removable,
maybe controller should be rescan for card. But if assume card is
non-removable, need to restore the old value at registers.
We store the value of FIFOTH at probe time and then restore it in
dw_mci_resume().
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch adds quirks and capabilities to platdata.
Some cards don't use the CDn pin; in that case, we assume the card's
inserted. Some boards need other capabilities. So, we add capabilities
in the board's platdata.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Currently kunmap_atomic() doesn't take into account the offset, used
with kmap_atomic(). On platforms, where kunmap_atomic() is not a NOP,
this will lead to problems, when offset != 0.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
At power off, reset OCR mask to be the highest possible voltage
supported for the current mmc host.
This solves the re-initialization during the power up sequence.
The voltage may have been decreased due to the card accepts a lower
voltage than the voltage used during the initialization sequence.
We need to reset the voltage to by the host highest possible value
since according to specification the initialization must always be
done at high voltage.
Reviewed-by: Jonas Aberg <jonas.aberg@stericsson.com>
Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
When using mmc_try_claim_host the corresponding release
function is mmc_do_release_host, which then also must
be exported.
Reviewed-by: Jonas Aberg <jonas.aberg@stericsson.com>
Reviewed-by: Sebastian Rasmussen <sebastian.rasmussen@stericsson.com>
Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
During redetection of a SDIO card, a request for a new card RCA
was submitted to the card, but was then overwritten by the old RCA.
This caused the card to be deselected instead of selected when using
the incorrect RCA. This bug's been present since the "oldcard"
handling was introduced in 2.6.32.
Signed-off-by: Stefan Nilsson XK <stefan.xk.nilsson@stericsson.com>
Reviewed-by: Ulf Hansson <ulf.hansson@stericsson.com>
Reviewed-by: Pawel Wieczorkiewicz <pawel.wieczorkiewicz@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: <stable@kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
count is only ever used by assigning to old_len if count == 0, and
then old_len isn't ever used at all. So, both are redundant. Fixes:
drivers/mmc/host/dw_mmc.c: In function ‘dw_mci_read_data_pio’:
drivers/mmc/host/dw_mmc.c:1034:32: warning: variable ‘old_len’ set but
not used [-Wunused-but-set-variable]
Signed-off-by: Chris Ball <cjb@laptop.org>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Tested-by: Marc Reilly <marc@cpdesign.com.au>
Tested-by: Eric Benard <eric@eukrea.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
It can be worked around using a GPIO which will be done for i.MX later.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Tested-by: Marc Reilly <marc@cpdesign.com.au>
Tested-by: Eric Benard <eric@eukrea.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Tested-by: Marc Reilly <marc@cpdesign.com.au>
Tested-by: Eric Benard <eric@eukrea.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
dma_unmap_sg() already flushes the cache, I don't get what this
code is doing here.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
* 'tty-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6: (76 commits)
pch_uart: reference clock on CM-iTC
pch_phub: add new device ML7213
n_gsm: fix UIH control byte : P bit should be 0
n_gsm: add a documentation
serial: msm_serial_hs: Add MSM high speed UART driver
tty_audit: fix tty_audit_add_data live lock on audit disabled
tty: move cd1865.h to drivers/staging/tty/
Staging: tty: fix build with epca.c driver
pcmcia: synclink_cs: fix prototype for mgslpc_ioctl()
Staging: generic_serial: fix double locking bug
nozomi: don't use flush_scheduled_work()
tty/serial: Relax the device_type restriction from of_serial
MAINTAINERS: Update HVC file patterns
tty: phase out of ioctl file pointer for tty3270 as well
tty: forgot to remove ipwireless from drivers/char/pcmcia/Makefile
pch_uart: Fix DMA channel miss-setting issue.
pch_uart: fix exclusive access issue
pch_uart: fix auto flow control miss-setting issue
pch_uart: fix uart clock setting issue
pch_uart : Use dev_xxx not pr_xxx
...
Fix up trivial conflicts in drivers/misc/pch_phub.c (same patch applied
twice, then changes to the same area in one branch)
To support MMC aggressive clock gating the driver has to stop the
interface clock when the .set_ios() method is called with .clock == 0.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Some TOSHIBA MMC cards only support sector addressing even though the
size is < 2GB. According to JEDEC Spec JESD84-A441-1 the ocr register
(bits 30, 29) determine byte/sector mode. Use them.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
sdio_reset sends a CMD52 to reset the sdio card. This is highly
recommended for sdio cards being reinitialized. Since we do not
know if the card is being reinitialized we just send the command.
SD/eMMC cards are supposed to ignore the CMD before the CMD0.
Document why we are doing this.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
* 'x86-platform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (27 commits)
x86: Clean up apic.c and apic.h
x86: Remove superflous goal definition of tsc_sync
x86: dt: Correct local apic documentation in device tree bindings
x86: dt: Cleanup local apic setup
x86: dt: Fix OLPC=y/INTEL_CE=n build
rtc: cmos: Add OF bindings
x86: ce4100: Use OF to setup devices
x86: ioapic: Add OF bindings for IO_APIC
x86: dtb: Add generic bus probe
x86: dtb: Add support for PCI devices backed by dtb nodes
x86: dtb: Add device tree support for HPET
x86: dtb: Add early parsing of IO_APIC
x86: dtb: Add irq domain abstraction
x86: dtb: Add a device tree for CE4100
x86: Add device tree support
x86: e820: Remove conditional early mapping in parse_e820_ext
x86: OLPC: Make OLPC=n build again
x86: OLPC: Remove extra OLPC_OPENFIRMWARE_DT indirection
x86: OLPC: Cleanup config maze completely
x86: OLPC: Hide OLPC_OPENFIRMWARE config switch
...
Fix up conflicts in arch/x86/platform/ce4100/ce4100.c
This patch adds DDR mode support to dw_mmc.
If we set any bit in UHS_REG bit[16:31], the card of that slot is
supported for DDR mode. For example, if UHS_REG[16] is set, card
number 0 is DDR mode.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
drivers/mmc/host/via-sdmmc.c: In function ‘via_reset_pcictrl’:
drivers/mmc/host/via-sdmmc.c:805:8: warning: variable ‘addrbase’ set but
not used [-Wunused-but-set-variable]
Signed-off-by: Chris Ball <cjb@laptop.org>
Cc: Harald Welte <HaraldWelte@viatech.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Fixes:
drivers/mmc/host/cb710-mmc.c: In function ‘cb710_wait_while_busy’:
drivers/mmc/host/cb710-mmc.c:182:6: warning: variable ‘err’ set but not
used [-Wunused-but-set-variable]
Signed-off-by: Chris Ball <cjb@laptop.org>
Acked-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
drivers/mmc/host/sdhci-pci.c: In function ‘sdhci_pci_probe_slot’:
drivers/mmc/host/sdhci-pci.c:913:18: warning: variable ‘addr’ set but
not used [-Wunused-but-set-variable]
Signed-off-by: Chris Ball <cjb@laptop.org>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
This adds the mmc host driver for Freescale MXS-based SoC i.MX23/28.
The driver calls into mxs-dma via generic dmaengine api for both pio
and data transfer.
Thanks Chris Ball for the indentation patch.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
This switches the mxcmmc driver to use the dmaengine API. Unlike
the old one this one is always present in the tree, even if no DMA
is implemented, hence we can remove all the #ifdefs in from the driver.
The driver automatically switches to PIO mode if no DMA support or no
suitable channel is available.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch adds support for 8-bit buswidth.
dw_mmc can use 8-bit buswidth and set to CTYPE_8BIT in card-type register.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Use the new dmaengine helper functions, and drop the error check
on the returned cookier from the dmaengine - we recently
established that this is really not allowed to fail.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
This variable doesn't seem to be used for anything after the
other patches so just drop it.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
According to the DMA-API you shall unmap the sglists with the same
sglist length as passed into the mapping function, not the
returned value from the mapping function.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
As established for the MMCI, it is proper to map the DMA buffers
on the DMA engine which is the one actually performing the DMA.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Use the new dmaengine helper functions, and drop the error check
on the returned cookier from the dmaengine - we recently
established that this is really not allowed to fail.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The host_sglen is now actually used to keep track of whether DMA
is active or not, so rename and retype it to bool.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
According to the DMA-API you shall unmap the sglists with the same
sglist length as passed into the mapping function, not the
returned value from the mapping function.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
As established for the MMCI, it is proper to map the DMA buffers
on the DMA engine which is the one actually performing the DMA.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Use the new dmaengine helpers to make the code more readable.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Fixes the following:
- It is perfectly legal for the dma_map_sg() to return fewer
entries than were passed in.
- Supply the returned numer of (possibly coalesced) entries to
the device_pre_slave_sg() function.
- Use the proper original sg_len when unmapping the sglist
in the error path.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
As established for the MMCI, it is proper to map the DMA buffers
on the DMA engine which is the one actually performing the DMA.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
So we know the implementation and prototypes agree with each other.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reviewed-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The test file is created under debugfs, not sysfs. Also remove
the unnecessary default n.
Signed-off-by: Will Newton <will.newton@imgtec.com>
Reviewed-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Setting this bit in the clock enable register will stop the clock
when the card is in the IDLE state.
Signed-off-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
We need to run the card detect tasklet at the end of slot initialisation
as it is possible that a card has been inserted prior to boot, so we don't
see an insertion interrupt and now the card is sitting there inserted but
with no power to it.
Signed-off-by: Neil Jones <neil.jones@imgtec.com>
Signed-off-by: Will Newton <will.newton@imgtec.com>
Reviewed-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Currently MMC_MXC driver can be selected by all i.MX devices.
Restrict its use only for the appropriate processors.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add two large sequential I/O performance tests:
35. Large sequential read into scattered pages
36. Large sequential write from scattered pages
The tests measure transfer times for 10MiB, 100MiB, 1000MiB.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Existing performance tests measure single or sequential I/O speed.
Add two random I/O tests:
33. Random read performance by transfer size
34. Random write performance by transfer size
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The test area size was set to the preferred erase size but for comparison
purposes it is better if it is the same size for different devices. Make
it a multiple of preferred erase size that is greater than or equal to 4MiB.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This sdio card supports having its sdio clock shutdown.
It is also not using the SDIO IRQ, but rather uses a side gpio irq.
Signed-off-by: Pierre Tardy <tardyp@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Some sdio card are not following sdio standard, and do not work
when the sdio bus's clock is gated.
To keep functionnality for all legacy driver, we turn this quirk on
for every sdio card.
Drivers needs to disable the quirk manually when someone verifies that
their supported card works with clock gating.
Signed-off-by: Pierre Tardy <tardyp@gmail.com>
Acked-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Some cards have quirks valid for every platforms using current
platform quirk hooks leads to a lot of code and debug duplication.
So we inspire a bit from what exists in PCI subsystem and do our own
per vendorid/deviceid quirk. We still drop the complexity of the pci
quirk system (with special section tables, and so on).
That can be added later if needed.
Signed-off-by: Pierre Tardy <pierre.tardy@intel.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Since mmc clock gating can also be used as a power gating
tip, it's better to put the led blinking after having
ungated the clock.
Signed-off-by: Pierre Tardy <pierre.tardy@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
If the MMC host controller does not support waiting for card signaling
busy state (MMC_CAP_WAIT_WHILE_BUSY cap), there is no point in prining
the relevant warning message.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Reviewed-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Samsung SDHCI host controller supports the Auto CMD12.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
While the MMC handled the card's read only flag correctly on open,
it did not setup the flag in the allocated disk structure. The
consequence being that probing the /sys/class/block/mmcblkX/ro
attribute always reported 0.
Signed-off-by: Marc-Andre Hebert <hebert.marcandre@gmail.com>
Reviewed-by: Chris Ball <cjb@laptop.org>
Tested-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Enhanced area feature is a new feature defined in eMMC4.4 standard. This
user data area provides higher performance/reliability, at the expense
of using twice the effective media space due to the area using SLC.
The MMC driver now reads out the enhanced area offset and size and adds
them to the device attributes in sysfs. Enabling the enhanced area can
only be done once, and should be done in manufacturing. To use this
feature, bit ERASE_GRP_DEF should also be set.
Documentation/ABI/testing/sysfs-devices-mmc describes the two new
attributes.
Signed-off-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
Reviewed-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Code has been converted over to the new explicit on-stack plugging,
and delay users have been converted to use the new API for that.
So lets kill off the old plugging along with aops->sync_page().
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
30201e7f3 ("mmc: skip detection of nonremovable cards on rescan")
allowed skipping detection of nonremovable cards on mmc_rescan().
The intention was to only skip detection of hardwired cards that
cannot be removed, so make sure this is indeed the case by directly
checking for (lack of) MMC_CAP_NONREMOVABLE, instead of using
mmc_card_is_removable(), which is overloaded with
CONFIG_MMC_UNSAFE_RESUME semantics.
The user-visible symptom of the bug this patch fixes is that no
"mmc: card XXXX removed" message appears in dmesg when a card is
removed and CONFIG_MMC_UNSAFE_RESUME=y.
Reported-and-tested-by: Dmitry Shmidt <dimitrysh@google.com>
Reported-and-tested-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This fixes a bug introduced by 807e8e4067 ("mmc: Fix sd/sdio/mmc
initialization frequency retries") that prevented SDIO drivers from
performing SDIO commands in their probe routines -- the above patch
called mmc_claim_host() before sdio_add_func(), which causes a deadlock
if an external SDIO driver calls sdio_claim_host().
Fix tested on an OLPC XO-1.75 with libertas on SDIO.
Signed-off-by: Dmitry Shmidt <dimitrysh@google.com>
Reviewed-and-Tested-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The code path entered via mmc_host_enable() can include register
accesses to the HSMMC IP block. For this to work, both the device
interface clock and functional clock need to be enabled before
mmc_host_enable() is called. However, omap_hsmmc_probe() calls
mmc_host_enable() before enabling the device interface clock.
Fix by calling mmc_host_enable() after the device interface clock is
enabled.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Madhusudhan Chikkature Rajashekar <madhu.cr@ti.com>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
Cc: Kishore Kadiyala <kishore.kadiyala@ti.com>
Cc: Tero Kristo <Tero.Kristo@nokia.com>
Acked-by: Madhusudhan Chikkature Rajashekar <madhu.cr@ti.com>
Modifying the device & driver name from "mmci-omap-hs" to
"omap_hsmmc".
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Acked-by: Benoit Cousson<b-cousson@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP2420 platform consists of mmc block as in omap1 and not the
hsmmc block as present in omap2430, omap3, omap4 platforms.
Removing all base address macro defines except keeping one for OMAP2420 and
adapting only hsmmc device registration and driver to hwmod framework.
Changes involves:
1) Remove controller reset in devices.c which is taken care of
by hwmod framework.
2) Using omap-device layer to register device and utilizing data from
hwmod data file for base address, dma channel number, Irq_number,
device attribute.
3) Update the driver to use dev_attr to find whether controller
supports dual volt cards
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Reviewed-by: Balaji T K <balajitk@ti.com>
Cc: Benoit Cousson <b-cousson@ti.com>
CC: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Final step to eliminate of_platform_bus_type. They're all just
platform drivers now.
v2: fix type in pasemi_nand.c (thanks to Stephen Rothwell)
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Make Primecell driver probe functions take a const pointer to their
ID tables. Drivers should never modify their ID tables in their
probe handler.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
OMAP4 supports up to 5 MMC controllers, but only 3 of these were
initialized. MMC5 is used by wl12xx chip. So initialize MMC4 and MMC5.
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Signed-off-by: Panduranga Mallireddy <panduranga_mallireddy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Doing tiocmget was such fun we should do tiocmset as well for the same
reasons
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We don't actually need this and it causes problems for internal use of
this functionality. Currently there is a single use of the FILE * pointer.
That is the serial core which uses it to check tty_hung_up_p. However if
that is true then IO_ERROR is also already set so the check may be removed.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Based on a patch from Linus Walleij.
Add dmaengine based support for DMA to the MMCI driver, using the
Primecell DMA engine interface. The changes over Linus' driver are:
- rename txsize_threshold to dmasize_threshold, as this reflects the
purpose more.
- use 'mmci_dma_' as the function prefix rather than 'dma_mmci_'.
- clean up requesting of dma channels.
- don't release a single channel twice when it's shared between tx and rx.
- get rid of 'dma_enable' bool - instead check whether the channel is NULL.
- detect incomplete DMA at the end of a transfer. Some DMA controllers
(eg, PL08x) are unable to be configured for scatter DMA and also listen
to all four DMA request signals [BREQ,SREQ,LBREQ,LSREQ] from the MMCI.
They can do one or other but not both. As MMCI uses LBREQ/LSREQ for the
final burst/words, PL08x does not transfer the last few words.
- map and unmap DMA buffers using the DMA engine struct device, not the
MMCI struct device - the DMA engine is doing the DMA transfer, not us.
- avoid double-unmapping of the DMA buffers on MMCI data errors.
- don't check for negative values from the dmaengine tx submission
function - Dan says this must never fail.
- use new dmaengine helper functions rather than using the ugly function
pointers directly.
- allow DMA code to be fully optimized away using dma_inprogress() which
is defined to constant 0 if DMA engine support is disabled.
- request maximum segment size from the DMA engine struct device and
set this appropriately.
- removed checking of buffer alignment - the DMA engine should deal with
its own restrictions on buffer alignment, not the individual DMA engine
users.
- removed setting DMAREQCTL - this confuses some DMA controllers as it
causes LBREQ to be asserted for the last seven transfers, rather than
six SREQ and one LSREQ.
- removed burst setting - the DMA controller should not burst past the
transfer size required to complete the DMA operation.
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We don't need to store the number of bytes transferred in our host
structure - we can store this directly in data->bytes_xfered.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We don't need to switch to data available interrupts if there's at
least half a FIFO depth worth of data remaining, as we'll still get
the FIFO half full interrupt. Keep this interrupt masked off until
we have less than half the FIFO depth worth of data remaining.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The sg_miter API provides the required cache maintainence, so we don't
need to do that ourselves. Remove the unnecessary additional cache
maintainence.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The data counter counts the number of bytes transferred on the MMC bus.
When a FIFO overrun occurs, we will not have transferred a FIFOs-worth
of data to memory, and so the data counter will be a FIFOs-worth ahead.
If this occurs on a block boundary, we will report one too many sectors
as successful. Fix this.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We should not report incomplete blocks on error. Return the number of
bytes successfully transferred, rounded down to the nearest block.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When we encounter an error, make sure we complete the transaction
otherwise we'll leave the request dangling.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We want to have just CONFIG_ARCH_OMAP2, 3 and 4. The rest
are nowadays just subcategories of these.
Search and replace the following:
ARCH_OMAP2420 SOC_OMAP2420
ARCH_OMAP2430 SOC_OMAP2430
ARCH_OMAP3430 SOC_OMAP3430
No functional changes.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Thomas Weber <weber@corscience.de>
Acked-by: Sourav Poddar <sourav.poddar@ti.com>
The MMCIDATACNT register contain the number of byte left at error
not the number of words, so loose the << 2 thing. Further if CRC
fails on the first block, we may end up with a negative number
of transferred bytes which is not good, and the formula was in
wrong order.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The bfin_sdh driver allocates the wrong size for the private data
in the mmc_host. The first parameter of mmc_alloc_host should be
the size of the local driver struct rather than the common mmc_host.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: <stable@kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
We have 8-bit width support but is not a v3 controller.
So we need platform_8bit_width() to support 8-bit buswidth.
Also we need MMC_CAP_8_BIT_DATA, so we add it in platdata.
This gets 8-bit support working again on s3c, after we previously
disabled 8-bit by default on non-v3 controllers.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
clk_get() returns a struct clk cookie to the driver and some platforms
may return NULL if they only support a single clock. clk_get() has only
failed if it returns a ERR_PTR() encoded pointer.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Don't read the command response from the registers when either the
command timed out (because there was no response from the card) or
the checksum on the response was invalid.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Chris Ball <cjb@laptop.org>
Including usb.h once is enough in drivers/mmc/host/ushc.c
This removes the duplicate.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Chris Ball <cjb@laptop.org>
* 'fixes' of master.kernel.org:/home/rmk/linux-2.6-arm:
ALSA: AACI: fix timeout duration
ALSA: AACI: fix timeout condition checking
ARM: 6636/1: ep93xx: default multiplexed gpio ports to gpio mode
ARM: 6637/1: Make the argument to virt_to_phys() "const volatile"
ARM: twd: ensure timer reload is reprogrammed on entry to periodic mode
ARM: 6635/2: Configure reference clock for Versatile Express timers
ARM: versatile: name configuration options after actual board names
ARM: realview: name configuration options after actual board names
ARM: realview,vexpress: fix section mismatch warning for pen_release
ARM: 6632/3: mmci: stop using the blockend interrupts
Implement a suggestion from Russell to drop the use of blockend
interrupts altogether and instead rely on the data counter.
Tested with error-free cards on U300, U8500 and RealView PB1176.
Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The probe function adds the MMC host which can start accepting request
immediately. There is an assumption here that no requests happen
immediatly, but it's not always the case. This assumption can causes
a BUG() when the clocks are disabled. The fix is to just remove the
clock disable in the probe function.
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Remove parts of this driver which use internal API calls. This
replaces the calls as suggested by Russell King.
Cc: Russell King - ARM Linux <linux@arm.linux.org.uk>
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
Having conditional around the of_match_table and the of_node pointers
turns out to make driver code use ugly #ifdef blocks. Drop the
conditionals and remove the #ifdef blocks from the affected drivers.
Also tidy up minor whitespace issues within the same hunks.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Explicitly include err.h, of_address.h and of_irq.h.
Make use of machine_is() conditional on PPC.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* 'next-devicetree' of git://git.secretlab.ca/git/linux-2.6: (29 commits)
of/flattree: forward declare struct device_node in of_fdt.h
ipmi: explicitly include of_address.h and of_irq.h
sparc: explicitly cast negative phandle checks to s32
powerpc/405: Fix missing #{address,size}-cells in i2c node
powerpc/5200: dts: refactor dts files
powerpc/5200: dts: Change combatible strings on localbus
powerpc/5200: dts: remove unused properties
powerpc/5200: dts: rename nodes to prepare for refactoring dts files
of/flattree: Update dtc to current mainline.
of/device: Don't register disabled devices
powerpc/dts: fix syntax bugs in bluestone.dts
of: Fixes for OF probing on little endian systems
of: make drivers depend on CONFIG_OF instead of CONFIG_PPC_OF
of/flattree: Add of_flat_dt_match() helper function
of_serial: explicitly include of_irq.h
of/flattree: Refactor unflatten_device_tree and add fdt_unflatten_tree
of/flattree: Reorder unflatten_dt_node
of/flattree: Refactor unflatten_dt_node
of/flattree: Add non-boottime device tree functions
of/flattree: Add Kconfig for EARLY_FLATTREE
...
Fix up trivial conflict in arch/sparc/prom/tree_32.c as per Grant.
This patch adds support for handling SDIO interrupt on DaVinci MMC/SD
controller.
The patch has been tested on DM355 and DA850 EVMs with Marvell Libertas
based SDIO wireless LAN card.
Signed-off-by: Alagu Sankar <alagusankar@embwise.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The card is not always clocked and the clock frequency zero is perfectly
legal, thus this code in mmc_set_data_timeout() may cause a division by
zero. It will be triggered more often if you're using software clock
gating but can be triggered under other conditions too.
Reported-by: Pierre Tardy <tardyp@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Reviewed-by: Chris Ball <cjb@laptop.org>
Cc: <stable@kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
With current code card insert/eject interrupts will acknowledge outstanding
commands. Normally this seems to be no problem, however if the hardware gets
stuck and no interrupts for CMD_TIMEOUT or CMD_RESPEND are generated, then
inserting and ejecting cards will falsely acknowledge outstanding commands
from the core.
This patch changes the behavior so that CMDs are only acked, if
CMD_TIMEOUT or CMD_RESPEND is received.
Signed-off-by: Arnd Hannemann <arnd@arndnet.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
When doing excessive hotplug, e.g., repeated insert/eject operations,
the hardware may get confused to a point where no CMDTIMEOUT/CMDRESPEND
interrupts are generated any more. As a result requests get stuck, e.g.:
[ 360.351562] INFO: task kworker/u:0:5 blocked for more than 120 seconds.
[ 360.351562] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 360.359375] kworker/u:0 D c020c2b4 0 5 2 0x00000000
[ 360.367187] Backtrace:
[ 360.367187] [<c020bfb0>] (schedule+0x0/0x340) from [<c020c480>] (schedule_timeout+0x20/0x190)
[ 360.375000] r8:c702fd70 r7:00000002 r6:c702e000 r5:c702fdc4 r4:7fffffff
[ 360.375000] r3:c701e040
[ 360.382812] [<c020c460>] (schedule_timeout+0x0/0x190) from [<c020be78>] (wait_for_common+0xc4/0x150)
[ 360.390625] r6:c702e000 r5:c702fdc4 r4:7fffffff
[ 360.390625] [<c020bdb4>] (wait_for_common+0x0/0x150) from [<c020bfac>] (wait_for_completion+0x18/0x1c)
[ 360.398437] [<c020bf94>] (wait_for_completion+0x0/0x1c) from [<c0185590>] (mmc_wait_for_req+0x214/0x234)
[ 360.406250] [<c018537c>] (mmc_wait_for_req+0x0/0x234) from [<c01889d0>] (mmc_sd_switch+0xfc/0x114)
[ 360.414062] r7:c702fe4c r6:c702fe20 r5:c7179800 r4:00fffff0
[ 360.421875] [<c01888d4>] (mmc_sd_switch+0x0/0x114) from [<c0187f70>] (mmc_sd_setup_card+0x260/0x384)
[ 360.429687] [<c0187d10>] (mmc_sd_setup_card+0x0/0x384) from [<c01885e0>] (mmc_sd_init_card+0x13c/0x1e0)
[ 360.437500] [<c01884a4>] (mmc_sd_init_card+0x0/0x1e0) from [<c01887a8>] (mmc_attach_sd+0x124/0x1a8)
[ 360.445312] r8:c02db404 r7:ffffff92 r6:c702ff34 r5:c6007da8 r4:c6007c00
[ 360.453125] [<c0188684>] (mmc_attach_sd+0x0/0x1a8) from [<c0185140>] (mmc_rescan+0x248/0x2f0)
[ 360.460937] r5:c6007da8 r4:c6007c00
[ 360.468750] [<c0184ef8>] (mmc_rescan+0x0/0x2f0) from [<c00467f0>] (process_one_work+0x1ec/0x318)
[ 360.476562] r7:c6007da8 r6:00000000 r5:c710ec00 r4:c701bde0
[ 360.484375] [<c0046604>] (process_one_work+0x0/0x318) from [<c0047fb0>] (worker_thread+0x1b0/0x2cc)
[ 360.492187] [<c0047e00>] (worker_thread+0x0/0x2cc) from [<c004b338>] (kthread+0x8c/0x94)
[ 360.500000] [<c004b2ac>] (kthread+0x0/0x94) from [<c0037fc4>] (do_exit+0x0/0x590)
[ 360.507812] r7:00000013 r6:c0037fc4 r5:c004b2ac r4:c7021f00
This patch addresses this problem by introducing timeouts for outstanding
interrupts. If a hardware interrupt is missing, a soft reset will be
performed to bring the hardware back to a working state.
Tested with the SDHI hardware block in sh7372 / AP4EVB.
Signed-off-by: Arnd Hannemann <arnd@arndnet.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch implements SDIO IRQ support for mfds which
announce the TMIO_MMC_SDIO_IRQ flag for tmio_mmc.
If MMC_CAP_SDIO_IRQ is also set SDIO IRQ signalling is activated.
Tested with a b43-based wireless SDIO card and sh_mobile_sdhi.
Signed-off-by: Arnd Hannemann <arnd@arndnet.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
with "mmc: tmio: implement a bounce buffer for unaligned DMA"
gcc generates the following warnings:
drivers/mmc/host/tmio_mmc.c:654:6: warning: 'ret' may be used uninitialized in this function
drivers/mmc/host/tmio_mmc.c:730:6: warning: 'ret' may be used uninitialized in this function
This patch fixes these by setting ret to -EINVAL in the affected code paths.
Signed-off-by: Arnd Hannemann <arnd@arndnet.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
For example, with SDIO WLAN cards, some transfers happen with buffers at
odd addresses, whereas the SH-Mobile DMA engine requires even addresses
for SDHI. This patch extends the tmio driver with a bounce buffer, that
is used for single entry scatter-gather lists both for sending and
receiving. If we ever encounter unaligned transfers with multi-element
sg lists, this patch will have to be extended. For now it just falls
back to PIO in this and other unsupported cases.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
drivers/mmc/host/tmio_mmc.h is only used by drivers/mmc/host/tmio_mmc.c,
this needlessly complicates source-code handling.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
The easiest way to fall back to PIO, when a DMA descriptor allocation
fails is to disable DMA on the controller but continue with the current
request in PIO mode. This way tmio_mmc_start_dma() can become void, since
it cannot be failing any more. The current version is also broken: it is
testing a wrong pointer and thus failing to recognise, that a descriptor
allocation wasn't successful.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
The driver is capable of handling multi-element sg lists in both PIO and
DMA modes. In DMA mode this also allows to use the DMA sg capability more
efficiently and almost doubles the throughput.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
This way, the probe function may register debugfs files if it wants to.
This fixes a bug with mmc_test where mmc_test_register_file_test() is
called before the card's debugfs dir exists, and so it fails.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Tested-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Rewrite and clean up mmc_rescan() to properly retry frequencies lower
than 400kHz. Failures can happen both in sd_send_* calls and
mmc_attach_*. Break out "mmc_rescan_try_freq" from the frequency
selection loop. Symmetrize claim/release logic in mmc_attach_* API,
and move the sd_send_* calls there to make mmc_rescan easier to read.
Signed-off-by: Andy Ross <andy.ross@windriver.com>
Reviewed-and-Tested-by: Hein Tibosch <hein_tibosch@yahoo.es>
Reviewed-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
With the bus-width test patch, mmc_set_bus_width*() isn't called properly
when the driver doesn't set MMC_CAP_BUS_WIDTH and no DDR mode.
This patch fixes the regression by moving the call up before the cap test.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
This adds the mmc host driver for the Synopsys DesignWare mmc
host controller, found in a number of embedded SoC designs.
Signed-off-by: Will Newton <will.newton@imgtec.com>
Reviewed-by: Matt Fleming <matt@console-pimps.org>
Reviewed-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
SDHCI driver for Tegra. This driver plugs in as a new variant of
sdhci-pltfm, using the platform data structure passed in to specify the
GPIOs to use for card detect, write protect and card power enablement.
Original driver (of which only the header file is left):
Signed-off-by: Yvonne Yip <y@palm.com>
The rest, which has been rewritten by now:
Signed-off-by: Olof Johansson <olof@lixom.net>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Chris Ball <cjb@laptop.org>
Some controllers misparse segment length 0 as being 0, not 65536. Add
a quirk to deal with it.
Signed-off-by: Olof Johansson <olof@lixom.net>
Reviewed-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Since we make sure the clock is enabled in the mmc_host_clk_exit()
function we should expect a reference counter of 1, not 0.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Tested-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch supports controllers with no internal clock divider in SDHCI,
such as the s5pc210 board. The external clock divider can be used to
make a proper clock because SDHCI doesn't support internal clock divider
by itself.
If external clock divider type is selected, some functions related
to clock control will be overrided by other functions.
The current clock control index is added to let you know which
clock bus is used for SDHCI when overriding functions.
Checking functions are added into sdhci_s3c_consider_clock, because
the clock divider step is different from that of host controller.
Signed-off-by: Jeongbae Seo <jeongbae.seo@samsung.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch adds support for additional host capabilities like SD/MMC
high speed, SDHCI bus width, etc.
Signed-off-by: Jeongbae Seo <jeongbae.seo@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Some old MMC devices fail with the 4/8 bits the driver tries to use
exclusively. This patch adds a test for the given bus setup and falls
back to the lower bit mode (until 1-bit mode) when the test fails.
[Major rework and refactoring by tiwai]
[Quirk addition and many fixes by prakity]
Signed-off-by: Aries Lee <arieslee@jmicron.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Philip Rakity <prakity@marvell.com>
Tested-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
In case of failure, mmc_attach_sdio() will power off the SD bus.
Power it up and reinitialize before trying SD memory detection.
Reported-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Upon system resume, SDIO core must reinitialize cards that were
powered off during suspend.
If the card had its power kept during suspend (and thus it is
'powered-resumed'), SDIO core performs only a limited reinitializing,
mainly needed to make sure that the card wasn't removed/replaced.
If a __nonremovable__ card is powered-resumed, we can safely skip the
reinitializing phase.
Note: 9b966aa (mmc: sdio: fully reconfigure oldcard on resume) removed
the bus width reconfiguration since mmc_sdio_init_card already does it.
It is brought back now in case mmc_sdio_init_card is skipped.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Initial SDIO runtime PM implementation took a conservative approach
of powering up cards (and fully reinitializing them) on system suspend,
just before the suspend handlers of the relevant drivers were executed.
To avoid redundant power and reinitialization cycles, this patch removes
this behavior: if a card is already powered off when system suspend kicks
in, it is left at that state.
If a card is active when a system sleep starts, everything is
straightforward and works exactly like before. But if the card was
already suspended before the sleep began, then when the MMC core powers
it back up on resume, its run-time PM status has to be updated to reflect
the actual post-system sleep status.
The technique to do that is borrowed from the I2C runtime PM
implementation (for more info see Documentation/power/runtime_pm.txt).
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Reviewed-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
mmc_rescan() checks whether registered cards are still present before
skipping them, by calling the bus-specific ->detect() handler.
With buses that support runtime PM, the card may be powered off at
this point, so they need to be powered on and fully reinitialized before
->detect() executes.
This whole process is redundant with nonremovable cards; in those cases,
we can safely skip calling ->detect() and implicitly assume its success.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Reviewed-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
JMicron 388 SD/MMC combo controller supports the 1.8V low-voltage for
SD, but MMC doesn't work with the low-voltage, resulting in an error
at probing.
This patch adds the support for multiple voltage mask per device type,
so that SD works with 1.8V while MMC forces 3.3V. Here new ocr_avail_*
fields for each device are introduced, so that the actual OCR mask is
switched dynamically.
Also, the restriction of low-voltage in core/sd.c is removed when the
bit is allowed explicitly via ocr_avail_sd mask.
This patch was rewritten from scratch based on Aries' original code.
Signed-off-by: Aries Lee <arieslee@jmicron.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
More information should be shown when sdhci_dumpregs is called.
Knowing the command is useful for debugging, and Capability 1
is useful for SD v3.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Reviewed-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch modifies the MMC core code to optionally call the set_ios()
operation on the driver with the clock frequency set to 0 (gate) after
a grace period of at least 8 MCLK cycles, then restore it (ungate)
before any new request. This gives the driver the option to shut down
the MCI clock to the MMC/SD card when the clock frequency is 0, i.e.
the core has stated that the MCI clock does not need to be generated.
It is inspired by existing clock gating code found in the OMAP and
Atmel drivers and brings this up to the host abstraction. Gating is
performed before and after any MMC request.
This patchset implements this for the MMCI/PL180 MMC/SD host controller,
but it should be simple to switch OMAP/Atmel over to using this instead.
mmc_set_{gated,ungated}() add variable protection to the state holders
for the clock gating code. This is particularly important when ordinary
.set_ios() calls would race with the .set_ios() call resulting from a
delayed gate operation.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Reviewed-by: Chris Ball <cjb@laptop.org>
Tested-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch disables the broken ADMA on selected O2Micro devices.
Signed-off-by: Jennifer Li <Jennifer.li@o2micro.com>
Reviewed-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Remove release_resource() after release_mem_region().
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
This also fixes the build problem introduced by my previous patch
due to unhandled API changes introduced by commit:
99fc513101 (mmc: Move regulator handling closer to core)
Signed-off-by: Alberto Panizzo <maramaopercheseimorto@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This implementation is based on the pxamci.c driver and it will
be used to support the mx31_3ds machine.
Signed-off-by: Alberto Panizzo <maramaopercheseimorto@gmail.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Implement an sdhci-pltfm driver for the controller found in the
Marvell Dove SoC.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
CC: Saeed Bishara <saeed@marvell.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
* 'for-2.6.38' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq: (33 commits)
usb: don't use flush_scheduled_work()
speedtch: don't abuse struct delayed_work
media/video: don't use flush_scheduled_work()
media/video: explicitly flush request_module work
ioc4: use static work_struct for ioc4_load_modules()
init: don't call flush_scheduled_work() from do_initcalls()
s390: don't use flush_scheduled_work()
rtc: don't use flush_scheduled_work()
mmc: update workqueue usages
mfd: update workqueue usages
dvb: don't use flush_scheduled_work()
leds-wm8350: don't use flush_scheduled_work()
mISDN: don't use flush_scheduled_work()
macintosh/ams: don't use flush_scheduled_work()
vmwgfx: don't use flush_scheduled_work()
tpm: don't use flush_scheduled_work()
sonypi: don't use flush_scheduled_work()
hvsi: don't use flush_scheduled_work()
xen: don't use flush_scheduled_work()
gdrom: don't use flush_scheduled_work()
...
Fixed up trivial conflict in drivers/media/video/bt8xx/bttv-input.c
as per Tejun.
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (416 commits)
ARM: DMA: add support for DMA debugging
ARM: PL011: add DMA burst threshold support for ST variants
ARM: PL011: Add support for transmit DMA
ARM: PL011: Ensure IRQs are disabled in UART interrupt handler
ARM: PL011: Separate hardware FIFO size from TTY FIFO size
ARM: PL011: Allow better handling of vendor data
ARM: PL011: Ensure error flags are clear at startup
ARM: PL011: include revision number in boot-time port printk
ARM: vexpress: add sched_clock() for Versatile Express
ARM i.MX53: Make MX53 EVK bootable
ARM i.MX53: Some bug fix about MX53 MSL code
ARM: 6607/1: sa1100: Update platform device registration
ARM: 6606/1: sa1100: Fix platform device registration
ARM i.MX51: rename IPU irqs
ARM i.MX51: Add ipu clock support
ARM: imx/mx27_3ds: Add PMIC support
ARM: DMA: Replace page_to_dma()/dma_to_page() with pfn_to_dma()/dma_to_pfn()
mx51: fix usb clock support
MX51: Add support for usb host 2
arch/arm/plat-mxc/ehci.c: fix errors/typos
...
* 'for-linus' of git://codeaurora.org/quic/kernel/davidb/linux-msm: (35 commits)
mmc: msm_sdcc: Check for only DATA_END interrupt to end a request
mmc: msm_sdcc: Fix bug in PIO mode when data size is not word aligned
mmc: msm_sdcc: Reset SDCC in case of data transfer errors
mmc: msm_sdcc: Add prog done interrupt support
mmc: msm_sdcc: Fix possible circular locking dependency warning
MSM: Add USB support for MSM7x30
MSM: Add USB suport for QSD8x50
msm: initial framebuffer support
msm: add handling for clocks tagged as CLK_MINMAX
msm: trout: change name of pmdh_clk to mddi_clk
msm: add CLK_MINMAX to pmdh_clk
msm: trout: add gpio_to_irq
msm: iommu: Use the correct memory allocation flag
msm_serial: Remove redundant unlikely()
msm: iommu: Miscellaneous code cleanup
msm: iommu: Support cache-coherent memory access
msm: iommu: Definitions for extended memory attributes
msm: iommu: Kconfig dependency for the IOMMU API
msm: iommu: Check if device is already attached
msm: iommu: Kconfig item for cacheable page tables
...
Simplify the driver by removing the possibility to build it without the DMA
support and remove the respective Kconfig parameter.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Fixes for sdhci-of and ipmi drivers.
Auditing all drivers using of_get_property did not find other
occurrences likely to be used on LE platforms.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Some OF drivers could likely be used on non-powerpc OF based platforms,
so fix the kconfig depends to be CONFIG_OF instead of CONFIG_PPC_OF.
Compile tested on ARM and sparc.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Make the MMCI announcement printk say which primecell part number
has been found. Display the revision as an unsigned decimal, and
display only the first 8 hex digits of the base address unless it's
larger.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Workqueue creation API has been updated and flush_scheduled_work() is
deprecated and scheduled to be removed.
* core/core.c: Use alloc_ordered_workqueue() instead of
create_singlethread_workqueue(). This removes an unnecessary
rescuer.
* host/omap.c: Create, use and flush mmc_omap_wq instead of the
system_wq.
* Flush host->mmc_carddetect_work directly on removal instead of using
flush_scheduled_work().
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Chris Ball <cjb@laptop.org>
Cc: linux-mmc@vger.kernel.org
Conflicts:
MAINTAINERS
arch/arm/mach-omap2/pm24xx.c
drivers/scsi/bfa/bfa_fcpim.c
Needed to update to apply fixes for which the old branch was too
outdated.
In the error-path where PM notifies PM_POST_RESTORE, the rescan-blockage
should be cleared as well. Otherwise it'll be never re-probed.
Also, as a bonus, this fixes a bug in S4 with user-mode suspend in the
current code, as it sends PM_POST_RESTORE instead of
PM_POST_HIBERNATION wrongly.
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Based on report made by Yauhen in:
"MMC: Fix multiblock SDIO transfers in AT91 MCI" patch,
I report those changes to the brother driver: atmel-mci.
So, this patch sets SDIO transfer types: SDIO block and SDIO byte
transfers instead of using ordinary MMC block transfers.
It is checking opcode for SDIO CMD53 and setting transfer
type in MCI_CMDR register properly.
Reported-by: Yauhen Kharuzhy <yauhen.kharuzhy@promwad.com>
Cc: <stable@kernel.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The AT91 MCI has special SDIO transfer types: SDIO block and SDIO byte
transfers, but at91_mci driver doesn't use them and handles all SDIO
transfers as ordinary MMC block transfers. This causes problems for
multiple-block SDIO transfers (in particular for 256-bytes blocks).
Fix this situation by checking the opcode for SDIO CMD53 and setting
the transfer type in the AT91_MCI_CMDR register properly.
This patch was tested with libertas SDIO driver: problem with TX
timeouts on big packets was eliminated.
Signed-off-by: Yauhen Kharuzhy <yauhen.kharuzhy@promwad.com>
Cc: <stable@kernel.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
* msm-core: (28 commits)
msm: initial framebuffer support
msm: add handling for clocks tagged as CLK_MINMAX
msm: trout: change name of pmdh_clk to mddi_clk
msm: add CLK_MINMAX to pmdh_clk
msm: trout: add gpio_to_irq
msm: iommu: Use the correct memory allocation flag
msm_serial: Remove redundant unlikely()
msm: iommu: Miscellaneous code cleanup
msm: iommu: Support cache-coherent memory access
msm: iommu: Definitions for extended memory attributes
msm: iommu: Kconfig dependency for the IOMMU API
msm: iommu: Check if device is already attached
msm: iommu: Kconfig item for cacheable page tables
msm: iommu: Don't flush page tables if no devices attached
msm: iommu: Mark functions with the right section names
msm: iommu: Support for the 2nd GFX core's IOMMU
msm: iommu: Revise GFX2D0 IOMMU contexts and M2V mappings
msm: iommu: Revise GFX3D IOMMU contexts and M2V mappings
msm: iommu: Use more consistent naming in platform data
msm: iomap: Addresses and IRQs for 2nd GFX core IOMMU
...
* msm-mmc: (33 commits)
mmc: msm_sdcc: Check for only DATA_END interrupt to end a request
mmc: msm_sdcc: Fix bug in PIO mode when data size is not word aligned
mmc: msm_sdcc: Reset SDCC in case of data transfer errors
mmc: msm_sdcc: Add prog done interrupt support
mmc: msm_sdcc: Fix possible circular locking dependency warning
msm: initial framebuffer support
msm: add handling for clocks tagged as CLK_MINMAX
msm: trout: change name of pmdh_clk to mddi_clk
msm: add CLK_MINMAX to pmdh_clk
msm: trout: add gpio_to_irq
msm: iommu: Use the correct memory allocation flag
msm_serial: Remove redundant unlikely()
msm: iommu: Miscellaneous code cleanup
msm: iommu: Support cache-coherent memory access
msm: iommu: Definitions for extended memory attributes
msm: iommu: Kconfig dependency for the IOMMU API
msm: iommu: Check if device is already attached
msm: iommu: Kconfig item for cacheable page tables
msm: iommu: Don't flush page tables if no devices attached
msm: iommu: Mark functions with the right section names
...
The current code checks for both DATA_END and DATA_BLK_END bits in
MCI_STATUS register and ends a request only if both are set at a time.
The hardware doesn't always set DATA_BLK_END when DATA_END is set.
But DATA_END status itself is sufficient condition from hardware that
data transfer is done and hence, check for only DATA_END interrupt in
software to end a request.
Signed-off-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
The current code for PIO doesn't transfer whole data when data size
is not in multiple of 4 bytes. The last few bytes are not written to
the card resulting in no DATAEND interrupt from SDCC. This patch
allows data transfer for non-aligned data size in PIO mode.
Signed-off-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
SDCC uses an asynchronous FIFOs for data synchronization (one for TX
and one for RX). For any error when DPSM (Data path state machine) is
involved the transfer is terminated with the remaining data stuck inside
FIFOs. Reset the controller in case of data errors to ensure that
any left over data in FIFOs is flushed out and DPSM is in good state.
The following problems are observed without this reset functionality -
1. After the card is removed in an unsafe way (removed when there
is an on going data transfer), the card will not be detected upon
its next insertion. This is because the controller wouldn't respond
to few initialization commands.
2. When an error occurs for a data transfer in non-DMA mode, sometimes
we get spurious PIO interrupt after the request is processed.
Signed-off-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Enable prog done interrupt for stop command(CMD12) that is sent
after a multi-block write(CMD25). The PROG_DONE bit is set when
the card has finished its programming and is ready for next data.
After every write request the card will be polled for ready status
using CMD13. For a multi-block write(CMD25) before sending CMD13,
stop command (CMD12) will be sent. If we enable prog done interrupt
for CMD12, then CMD13 polling can be avoided. The prog done interrupt
means that the card is done with its programming and is ready for
next request.
Signed-off-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
In the context of request processing thread, data mover lock is
acquired after the host lock. In another context, in the completion
handler of data mover the locks are acquired in the reverse order,
resulting in possible circular lock dependency warning. Hence,
schedule a tasklet to process the dma completion so as to avoid
nested locks.
Signed-off-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
I misread the datasheet as if bypass mode was not available at all
on the ux500's, I was wrong. It is there, the datasheet just
states that you should not have to use it.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The Ux500 variant of this block has a different divider.
The value used right now is too big and which means a loss
in performance. This fix corrects it. Also expand the math
comments a bit so it's clear what's happening. Further
the Ux500 variant does not like if we use the BYPASS bit,
instead we are supposed to set the clock divider to zero.
Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The MMCIF controller on sh-mobile platforms can use the DMA controller for data
transfers. Interface to the SH dmaengine driver to enable DMA. We also have to
lower the maximum number of segments to match with the number od DMA
descriptors on SuperH, this doesn't significantly affect driver's PIO
performance.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
In sh_mmcif.c an event is used as a completion, switch over. When a
wait_for_completion*_timeout() returns, it suffices to check the remaining
time, setting an additional flag before waking up the waiting task only reduces
the race window, but does not eliminate it. This patch switches the driver to
use a completion to signal an interrupt, the only case, when an interrupt
should not wake up the waiter, is when an automatic CMD12 completes. Also fix
MODULE_ALIAS.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
We now:
* check for a v3 controller before setting 8-bit bus width
* offer a callback for platform code to switch to 8-bit mode, which
allows non-v3 controllers to support it
* rely on mmc->caps |= MMC_CAP_8_BIT_DATA; in platform code to specify
that the board designers have indeed brought out all the pins for
8-bit to the slot.
We were previously relying only on whether the *controller* supported
8-bit, which doesn't tell us anything about the pin configuration in
the board design.
This fixes the MMC card regression reported by Maxim Levitsky here:
http://thread.gmane.org/gmane.linux.kernel.mmc/4336
by no longer assuming that 8-bit works by default.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Tested-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Some board/card/host configurations are not capable of powering off the
card after boot.
To support such configurations, and to allow smoother transition to
runtime PM behavior, MMC_CAP_POWER_OFF_CARD is added, so hosts need to
explicitly indicate whether it's OK to power off their cards after boot.
SDIO core will enable runtime PM for a card only if that cap is set.
As a result, the card will be powered down after boot, and will only
be powered up again when a driver is loaded (and then it's up to the
driver to decide whether power will be kept or not).
This will prevent sdio_bus_probe() failures with setups that do not
support powering off the card.
Reported-and-tested-by: Daniel Drake <dsd@laptop.org>
Reported-and-tested-by: Arnd Hannemann <arnd@arndnet.de>
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Power off the card in mmc_sdio_detect __before__ a potential error
handler, which completely removes the card, executes, and only if the
card was successfully powered on beforehand.
While we're at it, use the _sync variant of the runtime PM put API, in
order to ensure that the card is left powered off in case an error
occurred, and the card is going to be removed.
Reproduced and tested on the OLPC XO-1.5.
Reported-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
While booting OMAP4 ES2.0 boards, cards on MMC1 and MMC2 controllers
are not getting detected sometimes.
During reset of command/data line, wrong pointer to base address
was passed while read operation to SYSCTL register, thus impacting
the updated reset logic.
Passing the correct base address fixes the issue.
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Madhusudhan Chikkature <madhu.cr@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
MMC hosts that poll for card detection by defining the MMC_CAP_NEEDS_POLL
flag have a race on rmmod, where the delayed work is cancelled without
waiting for completed polling. To prevent this a _sync version of the work
cancellation has to be used.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: <stable@kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
This adds some minor variant data and trickery to enable SDIO
on the ST Micro variants of MMCI/PL180.
Signed-off-by: Marcin Mielczarczyk <marcin.mielczarczyk@tieto.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
On the U300 the MCI_DATAEND and MCI_DATABLOCKEND IRQs can arrive
out-of-order. Replace an ugly #ifdef hack with a proper runtime
solution which models what is really happening.
In the U300 DMA mode and on all Ux500 models, the MCI_DATABLOCKEND
flag isn't properly cleared in hardware following and ACK leading
to all kind of weird behaviour when the flag is still up in
subsequent interrupts, so we add two flags indicating the
error and handle this runtime.
Cc: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The DBx500 variants have only one IRQ line hooked up. Allow these (and
any other implementations which choose to use only one irq) to work by
directing the PIO interrupts also to the first IRQ line.
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This moves some constants from sh_mmcif.c to sh_mmcif.h
so that they can be used in sh_mmcif_boot_init().
It also alters the definition of SOFT_RST_OFF from (0 << 31) to
~SOFT_RST_ON (= ~(1 << 31)). The former seems bogus. The latter is
consistent with the code in sh_mmcif_boot_init().
Cc: Yusuke Goda <yusuke.goda.sx@renesas.com>
Cc: Magnus Damm <magnus.damm@gmail.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
SDHC2 is newly added in C0 stepping of Langwell. Without the Moorestown
specific quirk, the default pci_probe will be called and crash the kernel.
This patch unblocks the crash problem on C0 by using the same probing
function as HC1, which limits the number of slots to one.
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Only these CPUs list the bug in their errata.
Signed-off-by: Eric Bénard <eric@eukrea.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch fixes timeout problems on i.MX's sdhci as suggested by
Richard Zhu.
Tested on:
- i.MX257: not needed
- i.MX357: needed
- i.MX515: needed
More details can be found here:
http://lists.infradead.org/pipermail/linux-arm-kernel/2010-October/029748.html
Signed-off-by: Eric Bénard <eric@eukrea.com>
Tested-by: Shawn Guo <shawn.gsc@gmail.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
A little more work was needed for SDIO IRQ wakeups to be functional.
Wake-on-WLAN on the SD WiFi adapter in the XO-1.5 laptop is now working.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Improves error handling in the ushc driver.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
We should not call mmc_card_set_ddr_mode() if we are in single data
mode. This sets DDR and causes the kernel log to say the card is DDR
when it is not.
Explicitly set ddr to 0 rather then rely on MMC_SDR_MODE being 0 when
doing the checks.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Adding card detect callback function and card detect configuration
function for MMC1 Controller on OMAP4.
Card detect configuration function does initial configuration of the
MMC Control & PullUp-PullDown registers of Phoenix.
For MMC1 Controller, card detect interrupt source is
twl6030 which is non-gpio. The card detect call back function provides
card present/absent status by reading MMC Control register present
on twl6030.
Since OMAP4 doesn't use any GPIO line as used in OMAP3 for card detect,
the suspend/resume initialization which was done in omap_hsmmc_gpio_init
previously is moved to the probe thus making it generic for both OMAP3 &
OMAP4.
Cc: Tony Lindgren <tony@atomide.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Adjust the tmio_mmc block size check to accept 2-byte requests in 4-bit
mode if the hardware supports it.
Tested with the SDHI hardware block included in sh7724.
Signed-off-by: Yusuke Goda <yusuke.goda.sx@renesas.com>
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Acked-by: Magnus Damm <damm@opensource.se>
Tested-by: Arnd Hannemann <arnd@arndnet.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In some platforms (e.g. AP4EVB) the card detect pin of a slot is not
directly connected to the sh_mmcif controller, so that polling needs
to be used. To overcome the overhead induced by querying the controller
on each poll cycle, card detection can be handled in the platform code
more efficiently.
This patch exposes a get_cd hook for that purpose.
Signed-off-by: Arnd Hannemann <arnd@arndnet.de>
Tested-by: Yusuke Goda <yusuke.goda.sx@renesas.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Some controllers, supported by the tmio_mmc driver do not have the card
detect pin of a slot connected, so that polling needs to be used and
card detection is handled by other means.
This patch exposes a get_cd hook for that purpose.
Signed-off-by: Arnd Hannemann <arnd@arndnet.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (66 commits)
mmc: add new sdhci-pxa driver for Marvell SoCs
mmc: make number of mmcblk minors configurable
mmc_spi: Recover from CRC errors for r/w operation over SPI.
mmc: sdhci-pltfm: add -pltfm driver for imx35/51
mmc: sdhci-of-esdhc: factor out common stuff
mmc: sdhci_pltfm: pass more data on custom init call
mmc: sdhci: introduce get_ro private write-protect hook
mmc: sdhci-pltfm: move .h file into appropriate subdir
mmc: sdhci-pltfm: Add structure for host-specific data
mmc: fix cb710 kconfig dependency warning
mmc: cb710: remove debugging printk (info duplicated from mmc-core)
mmc: cb710: clear irq handler on init() error path
mmc: cb710: remove unnecessary msleep()
mmc: cb710: implement get_cd() callback
mmc: cb710: partially demystify clock selection
mmc: add a file to debugfs for changing host clock at runtime
mmc: sdhci: allow for eMMC 74 clock generation by controller
mmc: sdhci: highspeed: check for mmc as well as sd cards
mmc: sdhci: Add Moorestown device support
mmc: sdhci: Intel Medfield support
...
This adds the support of atmel-mci sd/mmc driver in at91sam9g45 devices and
board files. This also configures the DMA controller slave interface for
at_hdmac dmaengine driver.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
* 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (163 commits)
omap: complete removal of machine_desc.io_pg_offst and .phys_io
omap: UART: fix wakeup registers for OMAP24xx UART2
omap: Fix spotty MMC voltages
ASoC: OMAP4: MCPDM: Remove unnecessary include of plat/control.h
serial: omap-serial: fix signess error
OMAP3: DMA: Errata i541: sDMA FIFO draining does not finish
omap: dma: Fix buffering disable bit setting for omap24xx
omap: serial: Fix the boot-up crash/reboot without CONFIG_PM
OMAP3: PM: fix scratchpad memory accesses for off-mode
omap4: pandaboard: enable the ehci port on pandaboard
omap4: pandaboard: Fix the init if CONFIG_MMC_OMAP_HS is not set
omap4: pandaboard: remove unused hsmmc definition
OMAP: McBSP: Remove null omap44xx ops comment
OMAP: McBSP: Swap CLKS source definition
OMAP: McBSP: Fix CLKR and FSR signal muxing
OMAP2+: clock: reduce the amount of standard debugging while disabling unused clocks
OMAP: control: move plat-omap/control.h to mach-omap2/control.h
OMAP: split plat-omap/common.c
OMAP: McBSP: implement functional clock switching via clock framework
OMAP: McBSP: implement McBSP CLKR and FSR signal muxing via mach-omap2/mcbsp.c
...
Fixed up trivial conflicts in arch/arm/mach-omap2/
{board-zoom-peripherals.c,devices.c} as per Tony
The old limit of number of minor numbers per mmcblk device was hardcoded
at 8. This isn't enough for some of the more elaborate partitioning
schemes, for example those used by Chrome OS.
Since there might be a bunch of systems out there with static /dev
contents that relies on the old numbering scheme, let's make it a
build-time option with the default set to the previous 8.
Also provide a boot/modprobe-time parameter to override the config
default: mmcblk.perdev_minors.
Signed-off-by: Olof Johansson <olof@lixom.net>
Cc: Mandeep Baines <msb@chromium.org>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The SPI bus is not reliable for large data transfers on all platforms.
The current mmc_spi driver fails SD read/write commands immediately if
occasional CRC errors are reported by the SD device. This patch makes
the operation recover from CRC errors by repeating the last SD command.
The retry count is set to 5 to ensure the driver passes stress tests.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
This driver adds basic support for the esdhc-core found on e.g.
imx35/51, as a platform driver.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Tested-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Put everything which can be shared between the OF and platform version
of this driver into a local .h file.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Tested-by: Eric Bénard <eric@eukrea.com>
[cjb: fix compile error: sdhci-esdhc.c->sdhci-esdhc.h]
Signed-off-by: Chris Ball <cjb@laptop.org>
The custom init call may need more data to perform its job, so we pass
it a pointer to pdata, too. Also, always use the platform_id specific
data even if platform_data is present. Doing that, platform_data can
additionally be parsed by init() for board-specific information (via
sdhci->mmc->parent).
(Note: the old behaviour was that you could override the platform_id
specific data with your own. However, one can still do this by using the
"sdhci" id instead of "sdhci-<something>".)
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Tested-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Some controllers handle their write-protection differently. Introduce a
callback to be able to handle it, ensuring the same locking takes place
for it. Rename the status variable to make it more obvious why the read
from the registers needs to be inverted.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Tested-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Make use of the include/linux/mmc directory.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Tested-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
We need to carry some information per host, e.g. the clock. Add a
structure for it and initialize it in the generic part. Also improve
the check for a parent.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Richard Röjfors <richard.rojfors.ext@mocean-labs.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Fix kconfig dependency warning to satisfy dependencies:
warning: (MMC_CB710 && MMC && PCI) selects CB710_CORE which has
unmet direct dependencies (MISC_DEVICES && PCI)
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Chris Ball <cjb@laptop.org>
Clock divider selection in partially verified, so document known facts
in code.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Chris Ball <cjb@laptop.org>
For debugging power management features it is convenient to have the
possibility of changing the MMC host controller clock at runtime. This
patch adds a 'clock' file for this under the MMC host root of debugfs.
Usage is as follows:
# cat /sys/kernel/debug/mmc0/clock
52000000
# echo "1000000000" > /sys/kernel/debug/mmc0/clock
# cat /sys/kernel/debug/mmc0/clock
52000000
# echo "48000000" > /sys/kernel/debug/mmc0/clock
# cat /sys/kernel/debug/mmc0/clock
48000000
The middle example shows limits being applied by the host driver.
Signed-off-by: Andy Shevchenko <ext-andriy.shevchenko@nokia.com>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
[cjb: modify changelog language]
Signed-off-by: Chris Ball <cjb@laptop.org>
Snippet of code for how adaptation layer should handle the call:
/*
* eMMC spec calls for the host to send 74 clocks to the card
* during initialization, right after voltage stabilization.
* create the clocks manually right here.
*/
void generate_init_clocks_A0(struct sdhci_host *host, u8 power_mode)
{
struct sdhci_mmc_slot *slot = sdhci_priv(host);
if (slot->power_mode == MMC_POWER_UP &&
power_mode == MMC_POWER_ON) {
/* controller specific code here */
/* slot->power_mode holds previous power setting */
}
slot->power_mode = power_mode;
}
Signed-off-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The SD and MMC code set highspeed using different constants.
Change the sd driver to recognize this and switch to high speed.
Validated code when testing eMMC dual data rate.
Signed-off-by: Philip Rakity <prakity@marvell.com>
[cjb: changelog + indentation fixes]
Signed-off-by: Chris Ball <cjb@laptop.org>
This adds the basic identifiers. Due to the various chip quirks it's not
enough to make MRST support very useful for earlier steppings but that can
follow.
(I'm currently trying to verify which steps actually matter outside Intel
so I can avoid unneeded stuff going upstream)
[Extracted from original development]
Signed-off-by: JiebingLi <jiebing.li@intel.com>
[Folds in fixes]
Signed-off-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Basic support for the Intel Medfield devices
Give them their own quirks as we will need to update this later.
Signed-off-by: Xiaochen Shen <xiaochen.shen@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Currently we write it to the chip data, but if the probe handler overrides
it we ignore the new value and keep using our cached one. Fix this so that
a probe handler can adjust the slot count.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Bring SDIO devices back to full power before their suspend
handler is invoked.
Doing so ensures that SDIO suspend/resume semantics are
maintained (drivers still get to decide whether their
card should be removed or kept during system suspend,
and at what power state), and that SDIO suspend/resume
execution paths are unchanged.
This is achieved by resuming a runtime-suspended SDIO device
in its ->prepare() PM callback (similary to the PCI subsystem).
Since the PM core always increments the run-time usage
counter before calling the ->prepare() callback and decrements
it after calling the ->complete() callback, it is guaranteed
that when the system will come out of suspend, our device's
power state will reflect its runtime PM usage counter.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Tested-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
To prevent an erroneous removal of the card, make sure
the device is powered when it is mmc_sdio_detect()ed.
This is required since mmc_sdio_detect may be invoked
while the device is runtime suspended (e.g., MMC core
is rescanning when system comes out of suspend).
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Tested-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Enable runtime PM for SDIO functions.
SDIO functions are initialized with a disabled runtime PM state,
and are set active (and their usage count is incremented)
only before potential drivers are probed.
SDIO function drivers that support runtime PM should call
pm_runtime_put_noidle() in their probe routine, and
pm_runtime_get_noresume() in their remove routine (very
similarly to PCI drivers).
In case a matching driver does not support runtime PM, power will
always be kept high (since the usage count is positive).
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Tested-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Enable runtime PM for new SDIO cards.
As soon as the card will be added to the device tree, runtime PM core
will release its power, since it doesn't have any users yet.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Tested-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Assign the generic runtime PM handlers for SDIO.
These handlers invoke the relevant SDIO function drivers'
handlers, if exist, otherwise they just return success
(so SDIO drivers don't have to define any runtime PM handlers
unless they need to).
Runtime PM is still disabled by default, so this patch alone
has no immediate effect.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Tested-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add MMC runtime PM handlers, which call mmc_power_save_host
and mmc_power_restore_host in response to runtime_suspend and
runtime_resume events.
Runtime PM is still disabled by default, so this patch alone
has no immediate effect.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Tested-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add a power_restore handler to the SDIO bus ops,
in order to support waking up SDIO cards that
were powered off by runtime pm.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Tested-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Allow power save/restore and their relevant mmc_bus_ops handlers
exit with a return value.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Tested-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
On resume, let mmc_sdio_init_card go all the way, instead
of skipping the reconfiguration of the card's speed and width.
This is needed to ensure cards wake up with their clock
reconfigured (otherwise it's kept low).
This patch also removes the explicit bus width reconfiguration
on resume, since now this is part of mmc_sdio_init_card.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Tested-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Some platforms based on sdhci-pltfm need to set their own quirks.
Previously to this patch, the quirks were in drivers/mmc/host/sdhci.h.
This patch splits drivers/mmc/host/sdhci.h into two parts:
* drivers/mmc/host/sdhci.h includes the HC registers and I/O accessors.
* include/linux/mmc/sdhci.h includes the sdhci structure and quirks.
Instead of including drivers/mmc/host/sdhci.h, -pltfm drivers should
now include include/linux/mmc/sdhci.h and include/linux/sdhci-pltfm.h.
This patch avoids adding/changing the calls/flags in the
sdhci_pltfm_data structure. It has been tested on STM platforms
(e.g. STx7106, STx7108, STx5206) where the driver is configured
and used as shown in the example below:
[snip]
static int mmc_pad_resources(struct sdhci_host *sdhci)
{
if (!devm_stm_pad_claim(sdhci->mmc->parent,
&stx7108_mmc_pad_config,
dev_name(sdhci->mmc->parent)))
return -ENODEV;
return 0;
}
static struct sdhci_pltfm_data stx7108_mmc_platform_data = {
.init = mmc_pad_resources,
.quirks = SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC,
};
static struct platform_device stx7108_mmc_device = {
.name = "sdhci",
[snip]
Note: drivers/mmc/host/sdhci.h now also includes linux/mmc/sdhci.h,
and no modifications should be needed on other sdhci-<XXX> drivers.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch fixes a warning when compiling the sdhci driver:
pwr may be used uninitialized in sdhci_set_power
Tested with the following compiler versions: 4.2.4 and 4.4.4
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch adds the suspend and resume functions
in the sdhci-pltfm device driver.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Usually there are multiple mmc host controllers; rename mmc queue thread
by host index so we can easily identify which controller it belongs to.
Signed-off-by: Ethan Du <ethan.too@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
One flaw with DDR support is that MMC core does not inform the driver
which DDR mode it has selected. This patch expands the ios->ddr flag
to do that.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The DDR support patch needs the following fixes:
- The block driver does not need to know about DDR, any more
than it needs to know about bus width.
- Not only the card must be switched to DDR mode. The host
controller must also be configured, which is done through
the 'set_ios()' function.
- Do not set the DDR mode state until after the switch command
is successful.
- Setting block length is not supported in DDR mode. Make that
a core function and change the other place it is used (mmc_test)
also.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add support for Dual Data Rate MMC cards as defined in the 4.4
specification.
Signed-off-by: Hanumath Prasad <hanumath.prasad@stericsson.com>
Cc: linux-mmc@vger.kernel.org
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Tested-by Zhangfei Gao <zhangfei.gao@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
After discovering a problem in regulator reference counting I took Mark
Brown's advice to move the reference count into the MMC core by making the
regulator status a member of struct mmc_host.
I took this opportunity to also implement NULL versions of
the regulator functions so as to rid the driver code from
some ugly #ifdef CONFIG_REGULATOR clauses.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: Sundar Iyer <sundar.iyer@stericsson.com>
Cc: Daniel Mack <daniel@caiaq.de>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: Matt Fleming <matt@console-pimps.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Cliff Brake <cbrake@bec-systems.com>
Cc: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
mmc_rescan() includes a pr_info which prints 4 lines each second for
hosts configured with MMC_CAP_NEEDS_POLL. This patch enables the message
only if CONFIG_MMC_DEBUG is selected. Tested on i.MX51's sdhci-esdhc.
Signed-off-by: Eric Bénard <eric@eukrea.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Hein Tibosch <hein_tibosch@yahoo.es>
Signed-off-by: Chris Ball <cjb@laptop.org>
In the latest releases of the mmc driver, the freq during initialization
is set to a fixed 400 Khz. This was reportedly too fast for several
users. As there doesn't seem to be an ideal frequency
which-works-for-all, Pierre suggested to let the driver try several
frequencies.
This patch implements that idea. It will try mmc-initialization using
several frequencies from an array 400, 300, 200 and 100.
In case SDIO is broken, it'll still try to detect SDMEM, also at different
freqs.
Signed-off-by: Hein Tibosch <hein_tibosch@yahoo.es>
Cc: Pierre Ossman <pierre@ossman.eu>
Reviewed-by: Chris Ball <cjb@laptop.org>
Tested-by: Chris Ball <cjb@laptop.org>
Cc: Ben Nizette <bn@niasdigital.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
Cc: Matt Fleming <matt@console-pimps.org>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
When a controller requires SDHCI_QUIRK_BROKEN_CARD_DETECTION, we poll
for card insertion/removal, and that creates interrupts. There's no
need to be doing this if we have a non-removable card.
This patch requires cards to be removable before we're willing to set
MMC_CAP_NEEDS_POLL.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Matt Fleming <matt@console-pimps.org>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
[cjb: modified changelog and code indentation]
Signed-off-by: Chris Ball <cjb@laptop.org>
There are two checks that need to be made when determining whether a
card is removable. A host controller may set MMC_CAP_NONREMOVABLE if the
controller does not support removing cards (e.g. eMMC), in which case
the card is physically non-removable. Also the 'mmc_assume_removable'
module parameter can be configured at module load time, in which case
the card may be logically non-removable.
A helper function keeps the logic in one place so that code always
checks both conditions.
Because this new function is likely to be called from modules we now
need to export the mmc_assume_removable symbol.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
The EXTRA_CFLAGS assignment in mmc/Makefile was not accomplishing
anything because this flag only has effect on sources at the same level
as the makefile (i.e., per directory). Since card/, core/, and host/
rely on MMC_DEBUG, the subdir-ccflags-y variant seems to be the
appropriate choice.
Signed-off-by: matt mooney <mfm@muteddisk.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
In a multi-controller environment it is helpful to know which controller
has problems.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch is necessary to gain the performance boost from 8-bit data
with the sdhci-stm driver.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
MMC_CAP_MMC_HIGHSPEED allows MMC and eMMC to negotiate up to 50M
instead of the previous limit of 25M.
Signed-off-by: Zhangfei Gao <zgao6@marvell.com>
Acked-by: Matt Fleming <matt@console-pimps.org>
Acked-by: Kyungmin Park <kmpark@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
While we're at it, add symbols for SDHCI_MAX_DIV_SPEC_{200,300}.
Signed-off-by: Zhangfei Gao <zhangfei.gao@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
SDHC Spec 3.0: Capabilities Register bits[15-08] are Base Clock Frequency
1.0/2.0: Capabilities Register bits[13-08] are Base Clock Frequency
Signed-off-by: Zhangfei Gao <zgao6@marvell.com>
Cc: David Vrabel <david.vrabel@csr.com>
Cc: Matt Fleming <matt@console-pimps.org>
Cc: Michal Miroslaw <mirqus@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Zhangfei Gao <zgao6@marvell.com>
Cc: Michał Mirosław <mirqus@gmail.com>
Cc: David Vrabel <david.vrabel@csr.com>
Reviewed-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The "6882a8c sdhci: Add better ADMA error reporting" commit added
sdhci_show_adma_error() which is built when DEBUG is defined. Since we
already have CONFIG_MMC_DEBUG used elsewhere in this driver, may as well
make consistent use of that config knob instead.
Signed-off-by: George G. Davis <gdavis@mvista.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Append .5 to KiB display when there are an odd number of sectors.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Correctly allocate memory to meet the host controller
driver's maximum segment size and count limits.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
As proposed by Greg K-H it is more logical to keep files for the mmc_test
driver under debugfs.
Additionally this patch brings seq_file API for show() method. It allows
to write unlimited data to the file.
Example of usage:
# mount -t debugfs none /sys/kernel/debug
# modprobe mmc_test
[ 581.395843] mmc_test mmc0:0001: Card claimed for testing.
# echo 25 > /sys/kernel/debug/mmc0/mmc0\:0001/test
[ 604.568542] mmc0: Starting tests of card mmc0:0001...
[ 604.582733] mmc0: Test case 25. Best-case read performance into scattered pages...
[ 604.923553] mmc0: Transfer of 8192 sectors (4096 KiB) took 0.124664314 seconds (33644 kB/s, 32856 KiB/s)
[ 604.933227] mmc0: Result: OK
[ 604.936248] mmc0: Tests completed.
# cat /sys/kernel/debug/mmc0/mmc0\:0001/test
Test 25: 0
1 8192 0.124664314 33644784
Signed-off-by: Andy Shevchenko <ext-andriy.shevchenko@nokia.com>
Cc: Greg KH <greg@kroah.com>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
Cc: Chris Ball <cjb@laptop.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Make it possible to get test results via sysfs. It helps to do tests
non-interactively. We have the file created under sysfs already and
can use it to show test results.
Prior to this patch, the "test" file under each card's sysfs node was
write-only, and results were obtained by looking at dmesg. This patch
improves programmatic access to the test results, making them available by
reading back from the same "test" file:
[root@host mmc0:e624]# echo 6 > test
[root@host mmc0:e624]# cat test
Test 6: 2
[cjb@laptop.org: changelog improvements]
Signed-off-by: Andy Shevchenko <ext-andriy.shevchenko@nokia.com>
Cc: Chris Ball <cjb@laptop.org>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
It's better to use strict_strtol() to convert user's input and strictly
check it. At least it forbids to interpret wrong input as a 0 and
prevents to run all tests.
Signed-off-by: Andy Shevchenko <ext-andriy.shevchenko@nokia.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
There are methods to check card type. Let's use them instead of direct checking
type bits.
Signed-off-by: Andy Shevchenko <ext-andriy.shevchenko@nokia.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The host controller driver limits I/O transfers to maximum
transfer size, maximum block count, maximum segment size
and maximum segment count. The performance tests were
not obeying these limits which meant they would not work
with some drivers. This patch fixes that.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Get rid of init_MUTEX[_LOCKED]() and use sema_init() instead.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mmc@vger.kernel.org
Signed-off-by: Chris Ball <cjb@laptop.org>
Global symbols should use their subsystem name in a prefixed fashion.
Signed-off-by: Andy Shevchenko <ext-andriy.shevchenko@nokia.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Conversion from struct device to struct mmc_card is used more than in one
place. Due to this it's better to have public macro for such thing.
Signed-off-by: Andy Shevchenko <ext-andriy.shevchenko@nokia.com>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Fix an issue found by klockwork. Just paranoia.
Signed-off-by: JiebingLi <jiebing.li@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add a driver for USB SD Host Controller devices. These devices are
Cypress Astoria chips with firmware compliant with issue 2 of CSR's USHC
specification.
[cjb: adapt to block layer deprecation of max_{hw,phys}_segs]
Signed-off-by: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
We have deprecated the distinction between hardware and physical
segments in the block layer. Consolidate the two limits into one in
drivers/mmc/.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
[cjb: rebased patch against Linus]
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: <linux-mmc@vger.kernel.org>
Acked-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
[cjb: rebased patch against Linus]
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
* 'for-2.6.37/barrier' of git://git.kernel.dk/linux-2.6-block: (46 commits)
xen-blkfront: disable barrier/flush write support
Added blk-lib.c and blk-barrier.c was renamed to blk-flush.c
block: remove BLKDEV_IFL_WAIT
aic7xxx_old: removed unused 'req' variable
block: remove the BH_Eopnotsupp flag
block: remove the BLKDEV_IFL_BARRIER flag
block: remove the WRITE_BARRIER flag
swap: do not send discards as barriers
fat: do not send discards as barriers
ext4: do not send discards as barriers
jbd2: replace barriers with explicit flush / FUA usage
jbd2: Modify ASYNC_COMMIT code to not rely on queue draining on barrier
jbd: replace barriers with explicit flush / FUA usage
nilfs2: replace barriers with explicit flush / FUA usage
reiserfs: replace barriers with explicit flush / FUA usage
gfs2: replace barriers with explicit flush / FUA usage
btrfs: replace barriers with explicit flush / FUA usage
xfs: replace barriers with explicit flush / FUA usage
block: pass gfp_mask and flags to sb_issue_discard
dm: convey that all flushes are processed as empty
...
* 'llseek' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/bkl:
vfs: make no_llseek the default
vfs: don't use BKL in default_llseek
llseek: automatically add .llseek fop
libfs: use generic_file_llseek for simple_attr
mac80211: disallow seeks in minstrel debug code
lirc: make chardev nonseekable
viotape: use noop_llseek
raw: use explicit llseek file operations
ibmasmfs: use generic_file_llseek
spufs: use llseek in all file operations
arm/omap: use generic_file_llseek in iommu_debug
lkdtm: use generic_file_llseek in debugfs
net/wireless: use generic_file_llseek in debugfs
drm: use noop_llseek
* 'trivial' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/bkl:
block: autoconvert trivial BKL users to private mutex
drivers: autoconvert trivial BKL users to private mutex
ipmi: autoconvert trivial BKL users to private mutex
mac: autoconvert trivial BKL users to private mutex
mtd: autoconvert trivial BKL users to private mutex
scsi: autoconvert trivial BKL users to private mutex
Fix up trivial conflicts (due to addition of private mutex right next to
deletion of a version string) in drivers/char/pcmcia/cm40[04]0_cs.c
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (278 commits)
arm: remove machine_desc.io_pg_offst and .phys_io
arm: use addruart macro to establish debug mappings
arm: return both physical and virtual addresses from addruart
arm/debug: consolidate addruart macros for CONFIG_DEBUG_ICEDCC
ARM: make struct machine_desc definition coherent with its comment
eukrea_mbimxsd-baseboard: Pass the correct GPIO to gpio_free
cpuimx27: fix compile when ULPI is selected
mach-pcm037_eet: fix compile errors
Fixing ethernet driver compilation error for i.MX31 ADS board
cpuimx51: update board support
mx5: add cpuimx51sd module and its baseboard
iomux-mx51: fix GPIO_1_xx 's IOMUX configuration
imx-esdhc: update devices registration
mx51: add resources for SD/MMC on i.MX51
iomux-mx51: fix SD1 and SD2's iomux configuration
clock-mx51: rename CLOCK1 to CLOCK_CCGR for better readability
clock-mx51: factorize clk_set_parent and clk_get_rate
eukrea_mbimxsd: add support for DVI displays
cpuimx25 & cpuimx35: fix OTG port registration in host mode
i.MX31 and i.MX35 : fix errate TLSbo65953 and ENGcm09472
...
Fix SDIO suspend/resume regression introduced by 4c2ef25fe0 "mmc: fix
all hangs related to mmc/sd card insert/removal during suspend/resume":
PM: Syncing filesystems ... done.
Freezing user space processes ... (elapsed 0.01 seconds) done.
Freezing remaining freezable tasks ... (elapsed 0.01 seconds) done.
Suspending console(s) (use no_console_suspend to debug)
pm_op(): platform_pm_suspend+0x0/0x5c returns -38
PM: Device pxa2xx-mci.0 failed to suspend: error -38
PM: Some devices failed to suspend
4c2ef25fe0 moved the card removal/insertion mechanism out of MMC's
suspend/resume path and into pm notifiers (mmc_pm_notify), and that
broke SDIO's expectation that mmc_suspend_host() will remove the card,
and squash the error, in case -ENOSYS is returned from the bus suspend
handler (mmc_sdio_suspend() in this case).
mmc_sdio_suspend() is using this whenever at least one of the card's SDIO
function drivers does not have suspend/resume handlers - in that case
it is agreed to force removal of the entire card.
This patch fixes this regression by trivially bringing back that part of
mmc_suspend_host(), which was removed by 4c2ef25fe0.
Reported-and-tested-by: Sven Neumann <s.neumann@raumfeld.com>
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Cc: Maxim Levitsky <maximlevitsky@gmail.com>
Cc: <stable@kernel.org>
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Chris Ball <cjb@laptop.org>
All file_operations should get a .llseek operation so we can make
nonseekable_open the default for future file operations without a
.llseek pointer.
The three cases that we can automatically detect are no_llseek, seq_lseek
and default_llseek. For cases where we can we can automatically prove that
the file offset is always ignored, we use noop_llseek, which maintains
the current behavior of not returning an error from a seek.
New drivers should normally not use noop_llseek but instead use no_llseek
and call nonseekable_open at open time. Existing drivers can be converted
to do the same when the maintainer knows for certain that no user code
relies on calling seek on the device file.
The generated code is often incorrectly indented and right now contains
comments that clarify for each added line why a specific variant was
chosen. In the version that gets submitted upstream, the comments will
be gone and I will manually fix the indentation, because there does not
seem to be a way to do that using coccinelle.
Some amount of new code is currently sitting in linux-next that should get
the same modifications, which I will do at the end of the merge window.
Many thanks to Julia Lawall for helping me learn to write a semantic
patch that does all this.
===== begin semantic patch =====
// This adds an llseek= method to all file operations,
// as a preparation for making no_llseek the default.
//
// The rules are
// - use no_llseek explicitly if we do nonseekable_open
// - use seq_lseek for sequential files
// - use default_llseek if we know we access f_pos
// - use noop_llseek if we know we don't access f_pos,
// but we still want to allow users to call lseek
//
@ open1 exists @
identifier nested_open;
@@
nested_open(...)
{
<+...
nonseekable_open(...)
...+>
}
@ open exists@
identifier open_f;
identifier i, f;
identifier open1.nested_open;
@@
int open_f(struct inode *i, struct file *f)
{
<+...
(
nonseekable_open(...)
|
nested_open(...)
)
...+>
}
@ read disable optional_qualifier exists @
identifier read_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
expression E;
identifier func;
@@
ssize_t read_f(struct file *f, char *p, size_t s, loff_t *off)
{
<+...
(
*off = E
|
*off += E
|
func(..., off, ...)
|
E = *off
)
...+>
}
@ read_no_fpos disable optional_qualifier exists @
identifier read_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
@@
ssize_t read_f(struct file *f, char *p, size_t s, loff_t *off)
{
... when != off
}
@ write @
identifier write_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
expression E;
identifier func;
@@
ssize_t write_f(struct file *f, const char *p, size_t s, loff_t *off)
{
<+...
(
*off = E
|
*off += E
|
func(..., off, ...)
|
E = *off
)
...+>
}
@ write_no_fpos @
identifier write_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
@@
ssize_t write_f(struct file *f, const char *p, size_t s, loff_t *off)
{
... when != off
}
@ fops0 @
identifier fops;
@@
struct file_operations fops = {
...
};
@ has_llseek depends on fops0 @
identifier fops0.fops;
identifier llseek_f;
@@
struct file_operations fops = {
...
.llseek = llseek_f,
...
};
@ has_read depends on fops0 @
identifier fops0.fops;
identifier read_f;
@@
struct file_operations fops = {
...
.read = read_f,
...
};
@ has_write depends on fops0 @
identifier fops0.fops;
identifier write_f;
@@
struct file_operations fops = {
...
.write = write_f,
...
};
@ has_open depends on fops0 @
identifier fops0.fops;
identifier open_f;
@@
struct file_operations fops = {
...
.open = open_f,
...
};
// use no_llseek if we call nonseekable_open
////////////////////////////////////////////
@ nonseekable1 depends on !has_llseek && has_open @
identifier fops0.fops;
identifier nso ~= "nonseekable_open";
@@
struct file_operations fops = {
... .open = nso, ...
+.llseek = no_llseek, /* nonseekable */
};
@ nonseekable2 depends on !has_llseek @
identifier fops0.fops;
identifier open.open_f;
@@
struct file_operations fops = {
... .open = open_f, ...
+.llseek = no_llseek, /* open uses nonseekable */
};
// use seq_lseek for sequential files
/////////////////////////////////////
@ seq depends on !has_llseek @
identifier fops0.fops;
identifier sr ~= "seq_read";
@@
struct file_operations fops = {
... .read = sr, ...
+.llseek = seq_lseek, /* we have seq_read */
};
// use default_llseek if there is a readdir
///////////////////////////////////////////
@ fops1 depends on !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier readdir_e;
@@
// any other fop is used that changes pos
struct file_operations fops = {
... .readdir = readdir_e, ...
+.llseek = default_llseek, /* readdir is present */
};
// use default_llseek if at least one of read/write touches f_pos
/////////////////////////////////////////////////////////////////
@ fops2 depends on !fops1 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read.read_f;
@@
// read fops use offset
struct file_operations fops = {
... .read = read_f, ...
+.llseek = default_llseek, /* read accesses f_pos */
};
@ fops3 depends on !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier write.write_f;
@@
// write fops use offset
struct file_operations fops = {
... .write = write_f, ...
+ .llseek = default_llseek, /* write accesses f_pos */
};
// Use noop_llseek if neither read nor write accesses f_pos
///////////////////////////////////////////////////////////
@ fops4 depends on !fops1 && !fops2 && !fops3 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read_no_fpos.read_f;
identifier write_no_fpos.write_f;
@@
// write fops use offset
struct file_operations fops = {
...
.write = write_f,
.read = read_f,
...
+.llseek = noop_llseek, /* read and write both use no f_pos */
};
@ depends on has_write && !has_read && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier write_no_fpos.write_f;
@@
struct file_operations fops = {
... .write = write_f, ...
+.llseek = noop_llseek, /* write uses no f_pos */
};
@ depends on has_read && !has_write && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read_no_fpos.read_f;
@@
struct file_operations fops = {
... .read = read_f, ...
+.llseek = noop_llseek, /* read uses no f_pos */
};
@ depends on !has_read && !has_write && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
@@
struct file_operations fops = {
...
+.llseek = noop_llseek, /* no read or write fn */
};
===== End semantic patch =====
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Julia Lawall <julia@diku.dk>
Cc: Christoph Hellwig <hch@infradead.org>
This adds a few registers to the MMCI/PL180 derivates that
is used for some odd control stuff like SDIO.
Signed-off-by: Marcin Mielczarczyk <marcin.mielczarczyk@tieto.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The block device drivers have all gained new lock_kernel
calls from a recent pushdown, and some of the drivers
were already using the BKL before.
This turns the BKL into a set of per-driver mutexes.
Still need to check whether this is safe to do.
file=$1
name=$2
if grep -q lock_kernel ${file} ; then
if grep -q 'include.*linux.mutex.h' ${file} ; then
sed -i '/include.*<linux\/smp_lock.h>/d' ${file}
else
sed -i 's/include.*<linux\/smp_lock.h>.*$/include <linux\/mutex.h>/g' ${file}
fi
sed -i ${file} \
-e "/^#include.*linux.mutex.h/,$ {
1,/^\(static\|int\|long\)/ {
/^\(static\|int\|long\)/istatic DEFINE_MUTEX(${name}_mutex);
} }" \
-e "s/\(un\)*lock_kernel\>[ ]*()/mutex_\1lock(\&${name}_mutex)/g" \
-e '/[ ]*cycle_kernel_lock();/d'
else
sed -i -e '/include.*\<smp_lock.h\>/d' ${file} \
-e '/cycle_kernel_lock()/d'
fi
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
A patch from Sukumar Ghorai <s-ghorai@ti.com> changed the
nwires to use caps instead. However, nwires is still
needed for the earlier controller.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Sukumar Ghorai <s-ghorai@ti.com>
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
On OMAP4, MMC2 controller has eMMC which draws power from VAUX regulator
on TWL. Though the eMMC supports dual voltage[1.8v/3v] as per ocr register,
its VCC is fixed at 3V for operation. With this once the mmc core selects
the minimum voltage[1.8] supported based on the ocr value read from OCR register,
eMMC will not get detected. Thus the platform data for MMC2 is updated with ocr
mask and same will be communicated to core which will set the regulator to
always operate at 3V when ever turned ON.
Cc: Tony Lindgren <tony@atomide.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In OMAP4, as per new PM programming model, the legacy registers
which were there in OMAP3 are all shifted by 0x100 while new one's
are added from offset 0 to 0x10.
For OMAP4, the register offset appending of 0x100 done in devices.c
currently, is moved to driver file.This change fits in for current
implementation as well as once the driver undergoes hwmod adaptation.
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The omap4 es2 hsmmc has a updated soft reset logic.After the
reset is issued monitor a 0->1 transition first. The reset of
CMD or DATA lines is complete only after a 0->1->0 transition
of SRC or SRD bits.
Signed-off-by: Madhusudhan Chikkature <madhu.cr@ti.com>
Tested-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
wires variable is renamed, extended and this single variable to be used to
pass the platform capabilities, e.g DDR mode. Also removed the hardcoded
value was using as bus-width.
Signed-off-by: Sukumar Ghorai <s-ghorai@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
If not all clocks have been defined in platform data, the driver will
cause a null pointer dereference when it is removed. This patch fixes
this issue.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
In the commit f522886e20 a merge conflict
in the sdhci-s3c driver been fixed. However the fix used incorrect
spinlock operation - it caused a race with sdhci interrupt service. The
correct way to solve it is to use spin_lock_irqsave/irqrestore() calls.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Currently the kernel is screaming about slowpath at me for the
wp/cd callbacks. Switch to the _cansleep variants so as to silence
this.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The card may be always present on the board, and for these cases neither
a status callback nor a card detect GPIO is required, and card detection
polling can be disabled.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
If an IRQ can be requested on the card detected GPIO, use it instead of
polling.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Barrier is deemed too heavy and will soon be replaced by FLUSH/FUA
requests. Deprecate barrier. All REQ_HARDBARRIERs are failed with
-EOPNOTSUPP and blk_queue_ordered() is replaced with simpler
blk_queue_flush().
blk_queue_flush() takes combinations of REQ_FLUSH and FUA. If a
device has write cache and can flush it, it should set REQ_FLUSH. If
the device can handle FUA writes, it should also set REQ_FUA.
All blk_queue_ordered() users are converted.
* ORDERED_DRAIN is mapped to 0 which is the default value.
* ORDERED_DRAIN_FLUSH is mapped to REQ_FLUSH.
* ORDERED_DRAIN_FLUSH_FUA is mapped to REQ_FLUSH | REQ_FUA.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Boaz Harrosh <bharrosh@panasas.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Nick Piggin <npiggin@kernel.dk>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Chris Wright <chrisw@sous-sol.org>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Alasdair G Kergon <agk@redhat.com>
Cc: Pierre Ossman <drzeus@drzeus.cx>
Cc: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Move the second if (reg & ...) test into the branch indicated by its
indentation. The test was previously always executed after the if
containing that branch, but it was always false unless the if branch was
taken.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable braces4@
position p1,p2;
statement S1,S2;
@@
(
if (...) { ... }
|
if (...) S1@p1 S2@p2
)
@script:python@
p1 << r.p1;
p2 << r.p2;
@@
if (p1[0].column == p2[0].column):
cocci.print_main("branch",p1)
cocci.print_secs("after",p2)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Chris Ball <cjb@laptop.org>
Cc: Pavel Pisa <ppisa@pikron.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If suspend called when kmmcd is doing host->ops->disable, as kmmcd already
increased host->en_dis_recurs to 1, the mmc_host_enable in suspend
function will return directly without increase the nesting_cnt, which will
cause the followed register access carried out to the disabled host.
mmc_suspend_host will enable host itself. No need to enable host before
it. Also works on kmmcd will get flushed in mmc_suspend_host, enable host
after it will be safe. So make the mmc_host_enable after it.
[cjb: rebase against current Linus]
Signed-off-by: Ethan <ethan.too@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Acked-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrei Warkentin