The PMUv2 specification reserves a number of event encodings
for common events.
This patch adds these events to the common event enumeration
in preparation for PMUv2 cores, such as Cortex-A15.
Acked-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The comment about measuring TLB misses and refills in the ARMv7 perf
backend makes little sense and refers loosely to raw counters that
should be used instead.
This patch removes the comments to avoid any confusion.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Modern ARMv7-A cores can optionally implement these new hardware
features:
- VFPv4:
The latest version of the ARMv7 vector floating-point extensions,
including hardware support for fused multiple accumulate. D16 or D32
variants may be implemented.
- Integer divide:
The SDIV and UDIV instructions provide signed and unsigned integer
division in hardware. When implemented, these instructions may be
available in either both Thumb and ARM, or Thumb only.
This patch adds new HWCAP defines to describe these new features. The
integer divide capabilities are split into two bits for ARM and Thumb
respectively. Whilst HWCAP_IDIVA should never be set if HWCAP_IDIVT is
clear, separating the bits makes it easier to interpret from userspace.
Signed-off-by: Will Deacon <will.deacon@arm.com>
To get hundredths of MHz the rate needs to be divided by 10'000.
Here is an example:
twd_timer_rate = 123456789
Before the patch:
twd_timer_rate / 1000000 = 123
(twd_timer_rate / 1000000) % 100 = 23
Result: 123.23MHz.
After being fixed:
twd_timer_rate / 1000000 = 123
(twd_timer_rate / 10000) % 100 = 45
Result: 123.45MHz.
Signed-off-by: Vitaly Kuzmichev <vkuzmichev@mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
If an ARM system has multiple cpus in the same socket and the
kernel is booted with maxcpus=1, secondary cpus are possible but
not present due to how platform_smp_prepare_cpus() is called.
Since most typical ARM processors don't actually support physical
hotplug, initialize the present map to be equal to the possible
map in generic ARM SMP code. Also, always call
platform_smp_prepare_cpus() as long as max_cpus is non-zero (0
means no SMP) to allow platform code to do any SMP setup.
After applying this patch it's possible to boot an ARM system
with maxcpus=1 on the command line and then hotplug in secondary
cpus via sysfs. This is more in line with how x86 does things.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: David Brown <davidb@codeaurora.org>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The scu_power_mode function can be used on UP builds as it drives signals
to an SOC power controller. So make it selectable for !SMP.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
By allowing code to detect whether DTCM or ITCM is present, code paths
involving TCM can be avoided when running on platforms that lack it.
This is good for creating single kernels across several archs, if some
of them utilize TCM but others don't.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The PB11MPCore reports "3" DTCM banks, but anything above 2 is an
"undefined" value, so push this to become 0. Further add some checks
if code is compiled to TCM even if there is no D/ITCM present in the
system, and if we can really fit the compiled code. We don't do the
BUG() since it's not helpful, it's better to deal with non-present
TCM dynamically. If there is nothing compiled to the TCM and no TCM
is detected, it will now just shut up even if TCM support is enabled.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Ensure that the meminfo array is sanity checked before we pass the
memory to memblock. This helps to ensure that memblock and meminfo
agree on the dimensions of memory, especially when more memory is
passed than the kernel can deal with.
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
armpmu_enable can be called in situations where no events are present
(for example, from the event rotation tick after a profiled task has
exited). In this case, we currently start the PMU anyway which may
leave it active inevitably without any events being monitored.
This patch adds a simple check to the enabling code so that we avoid
starting the PMU when no events are present.
Cc: <stable@kernel.org>
Reported-by: Ashwin Chaugle <ashwinc@codeaurora.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The SVC IRQ, prefetch and data abort handlers preserve the SPSR value
via r5 across the exception. Rather than re-loading it from pt_regs,
use the preserved value instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tail-call the main C data abort handler code from the per-CPU helper
code. Update the comments in the code wrt the new calling and return
register state.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tail-call the main C prefetch abort handler code from the per-CPU
helper code. Also note that the helper function becomes ABI
compliant in terms of the registers preserved.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This avoids the irq entry assembly corrupting r5, thereby allowing it
to be preserved through to the svc exit code.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
All handlers now call trace_hardirqs_off, so move this common code into
the (svc|usr)_entry assembler macros.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As we no longer re-enable interrupts in these exception handlers, add
the irqsoff tracing calls to them so that the kernel tracks the state
more accurately.
Note that these calls are conditional on IRQSOFF_TRACER:
kernel ----------> user ---------> kernel
^ irqs enabled ^ irqs disabled
No kernel code can run on the local CPU until we've re-entered the
kernel through one of the exception handlers - and userspace can not
take any locks etc. So, the kernel doesn't care about the IRQ mask
state while userspace is running unless we're doing IRQ off latency
tracing. So, we can (and do) avoid the overhead of updating the IRQ
mask state on every kernel->user and user->kernel transition.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add irqtrace function calls to the undefined exception handler, so
that we get sane lockdep traces from locking problems in undefined
exception handlers.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Avoid enabling interrupts if the parent context had interrupts enabled
in the abort handler assembly code, and move this into the breakpoint/
page/alignment fault handlers instead.
This gets rid of some special-casing for the breakpoint fault handlers
from the low level abort handler path.
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There are SoCs where attempting to enter a low power state is ignored,
and the CPU continues executing instructions with all state preserved.
It is over-complex at that point to disable the MMU just to call the
resume path.
Instead, allow the suspend finisher to return error codes to abort
suspend in this circumstance, where the cpu_suspend internals will then
unwind the saved state on the stack. Also omit the tlb flush as no
changes to the page tables will have happened.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The perf_event overflow handler does not receive any caller-derived
argument, so many callers need to resort to looking up the perf_event
in their local data structure. This is ugly and doesn't scale if a
single callback services many perf_events.
Fix by adding a context parameter to perf_event_create_kernel_counter()
(and derived hardware breakpoints APIs) and storing it in the perf_event.
The field can be accessed from the callback as event->overflow_handler_context.
All callers are updated.
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1309362157-6596-2-git-send-email-avi@redhat.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add a NODE level to the generic cache events which is used to measure
local vs remote memory accesses. Like all other cache events, an
ACCESS is HIT+MISS, if there is no way to distinguish between reads
and writes do reads only etc..
The below needs filling out for !x86 (which I filled out with
unsupported events).
I'm fairly sure ARM can leave it like that since it doesn't strike me as
an architecture that even has NUMA support. SH might have something since
it does appear to have some NUMA bits.
Sparc64, PowerPC and MIPS certainly want a good look there since they
clearly are NUMA capable.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: David Miller <davem@davemloft.net>
Cc: Anton Blanchard <anton@samba.org>
Cc: David Daney <ddaney@caviumnetworks.com>
Cc: Deng-Cheng Zhu <dengcheng.zhu@gmail.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Robert Richter <robert.richter@amd.com>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/r/1303508226.4865.8.camel@laptop
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The nmi parameter indicated if we could do wakeups from the current
context, if not, we would set some state and self-IPI and let the
resulting interrupt do the wakeup.
For the various event classes:
- hardware: nmi=0; PMI is in fact an NMI or we run irq_work_run from
the PMI-tail (ARM etc.)
- tracepoint: nmi=0; since tracepoint could be from NMI context.
- software: nmi=[0,1]; some, like the schedule thing cannot
perform wakeups, and hence need 0.
As one can see, there is very little nmi=1 usage, and the down-side of
not using it is that on some platforms some software events can have a
jiffy delay in wakeup (when arch_irq_work_raise isn't implemented).
The up-side however is that we can remove the nmi parameter and save a
bunch of conditionals in fast paths.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Michael Cree <mcree@orcon.net.nz>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Deng-Cheng Zhu <dengcheng.zhu@gmail.com>
Cc: Anton Blanchard <anton@samba.org>
Cc: Eric B Munson <emunson@mgebm.net>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Don Zickus <dzickus@redhat.com>
Link: http://lkml.kernel.org/n/tip-agjev8eu666tvknpb3iaj0fg@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This avoids unnecessary instructions for CPUs which implement the IFAR
(instruction fault address register).
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This allows us to avoid moving registers twice to work around the
clobbered registers when we add calls to trace_hardirqs_{on,off}.
Ensure that all SVC handlers return with SPSR in r5 for consistency.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds support for platform_device_id tables, allowing new
PMU types to be registered with the correct type, without requiring
new platform_driver shims to provide the type. An single entry for
existing devices is provided.
Macros matching functionality of the of_device_id table macros are
provided for convenience.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Jamie Iles <jamie@jamieiles.com>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This is based on an earlier patch from Rob Herring <rob.herring@calxeda.com>
> Add OF match table to enable OF style driver binding. The dts entry is like
> this:
>
> pmu {
> compatible = "arm,cortex-a9-pmu";
> interrupts = <100 101>;
> };
>
> The use of pdev->id as an index breaks with OF device binding, so set the type
> based on the OF compatible string.
This modification sets the PMU hardware type based on data embedded in the
binding, allowing easy addition of new PMU types in future.
Support for new PMU types not provided by devicetree can be added later using
platform_device_id tables in a similar fashion.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Currently, the PMU reservation framework allows for multiple PMUs of
the same type to register themselves. This can lead to a bug with the
sequence:
register_pmu(pmu1);
reserve_pmu(pmu_type);
register_pmu(pmu2);
release_pmu(pmu1);
Here, pmu1 cannot be released, and pmu2 cannot be reserved.
This patch modifies register_pmu to reject registrations where a PMU is
already present, preventing this problem. PMUs which can have multiple
instances should not use the PMU reservation framework.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Currently, PMU platform_device reservation relies on some minor abuse
of the platform_device::id field for determining the type of PMU. This
is problematic for device tree based probing, where the ID cannot be
controlled.
This patch removes reliance on the id field, and depends on each PMU's
platform driver to figure out which type it is. As all PMUs handled by
the current platform_driver name "arm-pmu" are CPU PMUs, this
convention is hardcoded. New PMU types can be supported through the use
of {of,platform}_device_id tables
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There's no point checking to see whether IRQs were masked in the parent
context when returning from IRQ handling - the fact that we're handling
an IRQ means that the parent context must have had IRQs unmasked.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
irq_enter() and irq_exit() already take care of the preempt_count
handling for interrupts, which increment and decrement the hardirq
bits of the preempt count. So we can remove the preempt count handing
in our IRQ entry/exit assembly, like x86 did some 9 years ago.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Replace r4 with ip for calling abort helpers - ip is allowed to be
corrupted by called functions in the ABI, so it makes more sense to
use such a register.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Some user space applications are designed around the ability to perform
atomic operations on 64 bit values. Since this is natively possible
only with ARMv6k and above, let's provide a new kuser helper to perform
the operation with kernel supervision on pre ARMv6k hardware.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Tested-by: Dave Martin <dave.martin@linaro.org>
The first and second arguments shouldn't concern platform code, so
hide them from each platforms caller.
Tested-by: Kevin Hilman <khilman@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As we have core code dealing with CPU suspend/resume, we can
re-initialize the CPUs exception banked registers via that code rather
than having platforms deal with that level of detail. So, move the
call to cpu_init() out of platform code into core code.
Tested-by: Kevin Hilman <khilman@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
cpu_suspend() has a weird calling method which makes it only possible to
call from assembly code: it returns with a modified stack pointer to
finish the suspend, but on resume, it 'returns' via a provided pointer.
We can make cpu_suspend() appear to be a normal function merely by
swapping the resume pointer argument and the link register.
Do so, and update all callers to take account of this more traditional
behaviour.
Acked-by: Frank Hofmann <frank.hofmann@tomtom.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Save the suspend function pointer onto the stack for use when returning.
Allocate r2 to pass an argument to the suspend function.
Acked-by: Frank Hofmann <frank.hofmann@tomtom.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Avoid using r2 and r3 in the suspend code, allowing these to be
passed further into the function as arguments.
Acked-by: Frank Hofmann <frank.hofmann@tomtom.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Make cpu_suspend()..return function preserve r4 to r11 across a suspend
cycle. This is in preparation of relieving platform support code from
this task.
Acked-by: Frank Hofmann <frank.hofmann@tomtom.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Very little code is different between these two paths now, so extract
the common code.
Acked-by: Frank Hofmann <frank.hofmann@tomtom.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move the return address for cpu_resume to the top of stack so that
cpu_resume looks more like a normal function.
Acked-by: Frank Hofmann <frank.hofmann@tomtom.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Eliminate the differences between MULTI_CPU and non-MULTI_CPU resume
paths, making the saved structure identical irrespective of the way
the kernel was configured.
Acked-by: Frank Hofmann <frank.hofmann@tomtom.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
cpu_proc_init() does processor specific initialization, which we do
at boot time. We have been omitting to do this on resume, which
causes some of this initialization to be skipped. We've also been
skipping this on SMP initialization too.
Ensure that cpu_proc_init() is always called appropriately by
moving it into cpu_init(), and move cpu_init() to a more appropriate
point in the boot initialization.
Tested-by: Kevin Hilman <khilman@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When we bring a CPU online, we should wait for it to become active
before entering the idle thread, so we know that the scheduler and
thread migration is going to work.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Digging into some assembly file in order to get information about the
kuser helpers is not that convivial. Let's move that information to
a better formatted file in Documentation/arm/ and improve on it a bit.
Thanks to Dave Martin <dave.martin@linaro.org> for the initial cleanup and
clarifications.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Dave Martin <dave.martin@linaro.org>
The "Thumb bit" of a symbol is only really meaningful for function
symbols (STT_FUNC).
However, sometimes a branch is relocated against a non-function
symbol; for example, PC-relative branches to anonymous assembler
local symbols are typically fixed up against the start-of-section
symbol, which is not a function symbol. Some inline assembler
generates references of this type, such as fixup code generated by
macros in <asm/uaccess.h>.
The existing relocation code for R_ARM_THM_CALL/R_ARM_THM_JUMP24
interprets this case as an error, because the target symbol appears
to be an ARM symbol; but this is really not the case, since the
target symbol is just a base in these cases. The addend defines
the precise offset to the target location, but since the addend is
encoded in a non-interworking Thumb branch instruction, there is no
explicit Thumb bit in the addend. Because these instructions never
interwork, the implied Thumb bit in the addend is 1, and the
destination is Thumb by definition.
This patch removes the extraneous Thumb bit check for non-function
symbols, enabling modules containing the affected relocation types
to be loaded. No modification to the actual relocation code is
required, since this code does not take bit[0] of the
location->destination offset into account in any case.
Function symbols are always checked for interworking conflicts, as
before.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Dump out the following 16-bit instruction to the faulting instruction
in the Code: line. This allows Thumb-2 instructions to be properly
encoded.
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
If the page to cmpxchg is user mode read only (not write),
we should simulate a data abort first.
Signed-off-by: Po-Yu Chuang <ratbert@faraday-tech.com>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
If the DT physical address is zero, this is equivalent to no DT.
Especially when the actual RAM physical address is not located at zero,
the result of phys_to_virt() would point to la-la-land and crash the
kernel, which crash is completely silent this early during boot.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch fixes the lockdep warning of "unannotated irqs-off"[1].
After entering __irq_usr, arm core will disable interrupt automatically,
but __irq_usr does not annotate the irq disable, so lockdep may complain
the warning if it has chance to check this in irq handler.
This patch adds trace_hardirqs_off in __irq_usr before entering irq_handler
to handle the irq, also calls ret_to_user_from_irq to avoid calling
disable_irq again.
This is also a fix for irq off tracer.
[1], lockdep warning log of "unannotated irqs-off"
[ 13.804687] ------------[ cut here ]------------
[ 13.809570] WARNING: at kernel/lockdep.c:3335 check_flags+0x78/0x1d0()
[ 13.816467] Modules linked in:
[ 13.819732] Backtrace:
[ 13.822357] [<c01cb42c>] (dump_backtrace+0x0/0x100) from [<c06abb14>] (dump_stack+0x20/0x24)
[ 13.831268] r6:c07d8c2c r5:00000d07 r4:00000000 r3:00000000
[ 13.837280] [<c06abaf4>] (dump_stack+0x0/0x24) from [<c01ffc04>] (warn_slowpath_common+0x5c/0x74)
[ 13.846649] [<c01ffba8>] (warn_slowpath_common+0x0/0x74) from [<c01ffc48>] (warn_slowpath_null+0x2c/0x34)
[ 13.856781] r8:00000000 r7:00000000 r6:c18b8194 r5:60000093 r4:ef182000
[ 13.863708] r3:00000009
[ 13.866485] [<c01ffc1c>] (warn_slowpath_null+0x0/0x34) from [<c0237d84>] (check_flags+0x78/0x1d0)
[ 13.875823] [<c0237d0c>] (check_flags+0x0/0x1d0) from [<c023afc8>] (lock_acquire+0x4c/0x150)
[ 13.884704] [<c023af7c>] (lock_acquire+0x0/0x150) from [<c06af638>] (_raw_spin_lock+0x4c/0x84)
[ 13.893798] [<c06af5ec>] (_raw_spin_lock+0x0/0x84) from [<c01f9a44>] (sched_ttwu_pending+0x58/0x8c)
[ 13.903320] r6:ef92d040 r5:00000003 r4:c18b8180
[ 13.908233] [<c01f99ec>] (sched_ttwu_pending+0x0/0x8c) from [<c01f9a90>] (scheduler_ipi+0x18/0x1c)
[ 13.917663] r6:ef183fb0 r5:00000003 r4:00000000 r3:00000001
[ 13.923645] [<c01f9a78>] (scheduler_ipi+0x0/0x1c) from [<c01bc458>] (do_IPI+0x9c/0xfc)
[ 13.932006] [<c01bc3bc>] (do_IPI+0x0/0xfc) from [<c06b0888>] (__irq_usr+0x48/0xe0)
[ 13.939971] Exception stack(0xef183fb0 to 0xef183ff8)
[ 13.945281] 3fa0: ffffffc3 0001500c 00000001 0001500c
[ 13.953948] 3fc0: 00000050 400b45f0 400d9000 00000000 00000001 400d9600 6474e552 bea05b3c
[ 13.962585] 3fe0: 400d96c0 bea059c0 400b6574 400b65d8 20000010 ffffffff
[ 13.969573] r6:00000403 r5:fa240100 r4:ffffffff r3:20000010
[ 13.975585] ---[ end trace efc4896ab0fb62cb ]---
[ 13.980468] possible reason: unannotated irqs-off.
[ 13.985534] irq event stamp: 1610
[ 13.989044] hardirqs last enabled at (1610): [<c01c703c>] no_work_pending+0x8/0x2c
[ 13.997131] hardirqs last disabled at (1609): [<c01c7024>] ret_slow_syscall+0xc/0x1c
[ 14.005371] softirqs last enabled at (0): [<c01fe5e4>] copy_process+0x2cc/0xa24
[ 14.013183] softirqs last disabled at (0): [< (null)>] (null)
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
32bit and 64bit on x86 are tested and working. The rest I have looked
at closely and I can't find any problems.
setns is an easy system call to wire up. It just takes two ints so I
don't expect any weird architecture porting problems.
While doing this I have noticed that we have some architectures that are
very slow to get new system calls. cris seems to be the slowest where
the last system calls wired up were preadv and pwritev. avr32 is weird
in that recvmmsg was wired up but never declared in unistd.h. frv is
behind with perf_event_open being the last syscall wired up. On h8300
the last system call wired up was epoll_wait. On m32r the last system
call wired up was fallocate. mn10300 has recvmmsg as the last system
call wired up. The rest seem to at least have syncfs wired up which was
new in the 2.6.39.
v2: Most of the architecture support added by Daniel Lezcano <dlezcano@fr.ibm.com>
v3: ported to v2.6.36-rc4 by: Eric W. Biederman <ebiederm@xmission.com>
v4: Moved wiring up of the system call to another patch
v5: ported to v2.6.39-rc6
v6: rebased onto parisc-next and net-next to avoid syscall conflicts.
v7: ported to Linus's latest post 2.6.39 tree.
> arch/blackfin/include/asm/unistd.h | 3 ++-
> arch/blackfin/mach-common/entry.S | 1 +
Acked-by: Mike Frysinger <vapier@gentoo.org>
Oh - ia64 wiring looks good.
Acked-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch makes TTBR1 point to swapper_pg_dir so that global, kernel
mappings can be used exclusively on v6 and v7 cores where they are
needed.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit 228e548e (net: Add sendmmsg socket system call) added the new
sendmmsg syscall. Add this to the syscall table for ARM.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* To remove the risk of inconvenient register allocation decisions
by the compiler, these functions are separated out as pure
assembler.
* The apcs frame manipulation code is not applicable for Thumb-2
(and also not easily compatible). Since it's not essential to
have a full frame on these leaf assembler functions, the frame
manipulation is removed, in the interests of simplicity.
* Split up ldm/stm instructions to be compatible with Thumb-2,
as well as avoiding instruction forms deprecated on >= ARMv7.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Reviewed-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'for-2.6.40' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu:
percpu: Unify input section names
percpu: Avoid extra NOP in percpu_cmpxchg16b_double
percpu: Cast away printk format warning
percpu: Always align percpu output section to PAGE_SIZE
Fix up fairly trivial conflict in arch/x86/include/asm/percpu.h as per Tejun
Rather than having each platform class provide a mach/smp.h header for
smp_cross_call(), arrange for them to register the function with the
core ARM SMP code instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
If a dtb is passed to the kernel then the kernel needs to iterate
through compiled-in mdescs looking for one that matches and move the
dtb data to a safe location before it gets accidentally overwritten by
the kernel.
This patch creates a new function, setup_machine_fdt() which is
analogous to the setup_machine_atags() created in the previous patch.
It does all the early setup needed to use a device tree machine
description.
v5: - Print warning with neither dtb nor atags are passed to the kernel
- Fix bug in setting of __machine_arch_type to the selected machine,
not just the last machine in the list.
Reported-by: Tixy <tixy@yxit.co.uk>
- Copy command line directly into boot_command_line instead of cmd_line
v4: - Dump some output when a matching machine_desc cannot be found
v3: - Added processing of reserved list.
- Backed out the v2 change that copied instead of reserved the
dtb. dtb is reserved again and the real problem was fixed by
using alloc_bootmem_align() for early allocation of RAM for
unflattening the tree.
- Moved cmd_line and initrd changes to earlier patch to make series
bisectable.
v2: Changed to save the dtb by copying into an allocated buffer.
- Since the dtb will very likely be passed in the first 16k of ram
where the interrupt vectors live, memblock_reserve() is
insufficient to protect the dtb data.
[based on work originally written by Jeremy Kerr <jeremy.kerr@canonical.com>]
Tested-by: Tony Lindgren <tony@atomide.com>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
In preparation for adding device tree support, this patch consolidates
all of the atag-specific setup into a single function.
v5: - drop double printk("Machine; %s\n", ...); call.
- leave copying boot_command_line in setup_arch() since it isn't
atags specific.
v4: - adapt to the removal of lookup_machine_type()
- break out dump of machine_desc table into dump_machine_table()
because the device tree probe code will use it.
- Add for_each_machine_desc() macro
Tested-by: Tony Lindgren <tony@atomide.com>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
When initialising a PMU, there is a check to protect against races with
other CPUs filling all of the available event slots. Since armpmu_add
checks that an event can be scheduled, we do not need to do this at
initialisation time. Furthermore the current code is broken because it
assumes that atomic_inc_not_zero will unconditionally increment
active_counts and then tries to decrement it again on failure.
This patch removes the broken, redundant code.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Cc: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'driver-core-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6: (44 commits)
debugfs: Silence DEBUG_STRICT_USER_COPY_CHECKS=y warning
sysfs: remove "last sysfs file:" line from the oops messages
drivers/base/memory.c: fix warning due to "memory hotplug: Speed up add/remove when blocks are larger than PAGES_PER_SECTION"
memory hotplug: Speed up add/remove when blocks are larger than PAGES_PER_SECTION
SYSFS: Fix erroneous comments for sysfs_update_group().
driver core: remove the driver-model structures from the documentation
driver core: Add the device driver-model structures to kerneldoc
Translated Documentation/email-clients.txt
RAW driver: Remove call to kobject_put().
reboot: disable usermodehelper to prevent fs access
efivars: prevent oops on unload when efi is not enabled
Allow setting of number of raw devices as a module parameter
Introduce CONFIG_GOOGLE_FIRMWARE
driver: Google Memory Console
driver: Google EFI SMI
x86: Better comments for get_bios_ebda()
x86: get_bios_ebda_length()
misc: fix ti-st build issues
params.c: Use new strtobool function to process boolean inputs
debugfs: move to new strtobool
...
Fix up trivial conflicts in fs/debugfs/file.c due to the same patch
being applied twice, and an unrelated cleanup nearby.
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (60 commits)
sched: Fix and optimise calculation of the weight-inverse
sched: Avoid going ahead if ->cpus_allowed is not changed
sched, rt: Update rq clock when unthrottling of an otherwise idle CPU
sched: Remove unused parameters from sched_fork() and wake_up_new_task()
sched: Shorten the construction of the span cpu mask of sched domain
sched: Wrap the 'cfs_rq->nr_spread_over' field with CONFIG_SCHED_DEBUG
sched: Remove unused 'this_best_prio arg' from balance_tasks()
sched: Remove noop in alloc_rt_sched_group()
sched: Get rid of lock_depth
sched: Remove obsolete comment from scheduler_tick()
sched: Fix sched_domain iterations vs. RCU
sched: Next buddy hint on sleep and preempt path
sched: Make set_*_buddy() work on non-task entities
sched: Remove need_migrate_task()
sched: Move the second half of ttwu() to the remote cpu
sched: Restructure ttwu() some more
sched: Rename ttwu_post_activation() to ttwu_do_wakeup()
sched: Remove rq argument from ttwu_stat()
sched: Remove rq->lock from the first half of ttwu()
sched: Drop rq->lock from sched_exec()
...
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: Fix rt_rq runtime leakage bug
* syscore:
PM: Remove sysdev suspend, resume and shutdown operations
PM / PowerPC: Use struct syscore_ops instead of sysdevs for PM
PM / UNICORE32: Use struct syscore_ops instead of sysdevs for PM
PM / AVR32: Use struct syscore_ops instead of sysdevs for PM
PM / Blackfin: Use struct syscore_ops instead of sysdevs for PM
ARM / Samsung: Use struct syscore_ops for "core" power management
ARM / PXA: Use struct syscore_ops for "core" power management
ARM / SA1100: Use struct syscore_ops for "core" power management
ARM / Integrator: Use struct syscore_ops for core PM
ARM / OMAP: Use struct syscore_ops for "core" power management
ARM: Use struct syscore_ops instead of sysdevs for PM in common code
This patch migrates the implementation of the ptrace interface for
the core integer registers, legacy FPA registers and VFP registers
to use the regsets framework.
As an added bonus, all this stuff gets included in coredumps
at no extra cost. Without this patch, coredumps contained no
VFP state.
Third-party extension register sets (iwmmx, crunch) are not migrated
by this patch, and continue to use the old implementation;
these should be migratable without much extra work.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Will Deacon <Will.Deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
On some arches (x86, sh, arm, unicore, powerpc) the oops message would
print out the last sysfs file accessed.
This was very useful in finding a number of sysfs and driver core bugs
in the 2.5 and early 2.6 development days, but it has been a number of
years since this file has actually helped in debugging anything that
couldn't also be trivially determined from the stack traceback.
So it's time to delete the line. This is good as we need all the space
we can get for oops messages at times on consoles.
Acked-by: Phil Carmody <ext-phil.2.carmody@nokia.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'fixes' of master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: 6870/1: The mandatory barrier rmb() must be a dsb() in for device accesses
ARM: 6892/1: handle ptrace requests to change PC during interrupted system calls
ARM: 6890/1: memmap: only free allocated memmap entries when using SPARSEMEM
ARM: zImage: the page table memory must be considered before relocation
ARM: zImage: make sure not to relocate on top of the relocation code
ARM: zImage: Fix bad SP address after relocating kernel
ARM: zImage: make sure the stack is 64-bit aligned
ARM: RiscPC: acornfb: fix section mismatches
ARM: RiscPC: etherh: fix section mismatches
GDB's interrupt.exp test cases currenly fail on ARM. The problem is how do_signal
handled restarting interrupted system calls:
The entry.S assembler code determines that we come from a system call; and that
information is passed as "syscall" parameter to do_signal. That routine then
calls get_signal_to_deliver [*] and if a signal is to be delivered, calls into
handle_signal. If a system call is to be restarted either after the signal
handler returns, or if no handler is to be called in the first place, the PC
is updated after the get_signal_to_deliver call, either in handle_signal (if
we have a handler) or at the end of do_signal (otherwise).
Now the problem is that during [*], the call to get_signal_to_deliver, a ptrace
intercept may happen. During this intercept, the debugger may change registers,
including the PC. This is done by GDB if it wants to execute an "inferior call",
i.e. the execution of some code in the debugged program triggered by GDB.
To this purpose, GDB will save all registers, allocate a stack frame, set up
PC and arguments as appropriate for the call, and point the link register to
a dummy breakpoint instruction. Once the process is restarted, it will execute
the call and then trap back to the debugger, at which point GDB will restore
all registers and continue original execution.
This generally works fine. However, now consider what happens when GDB attempts
to do exactly that while the process was interrupted during execution of a to-be-
restarted system call: do_signal is called with the syscall flag set; it calls
get_signal_to_deliver, at which point the debugger takes over and changes the PC
to point to a completely different place. Now get_signal_to_deliver returns
without a signal to deliver; but now do_signal decides it should be restarting
a system call, and decrements the PC by 2 or 4 -- so it now points to 2 or 4
bytes before the function GDB wants to call -- which leads to a subsequent crash.
To fix this problem, two things need to be supported:
- do_signal must be able to recognize that get_signal_to_deliver changed the PC
to a different location, and skip the restart-syscall sequence
- once the debugger has restored all registers at the end of the inferior call
sequence, do_signal must recognize that *now* it needs to restart the pending
system call, even though it was now entered from a breakpoint instead of an
actual svc instruction
This set of issues is solved on other platforms, usually by one of two
mechanisms:
- The status information "do_signal is handling a system call that may need
restarting" is itself carried in some register that can be accessed via
ptrace. This is e.g. on Intel the "orig_eax" register; on Sparc the kernel
defines a magic extra bit in the flags register for this purpose.
This allows GDB to manage that state: reset it when doing an inferior call,
and restore it after the call is finished.
- On s390, do_signal transparently handles this problem without requiring
GDB interaction, by performing system call restarting in the following
way: first, adjust the PC as necessary for restarting the call. Then,
call get_signal_to_deliver; and finally just continue execution at the
PC. This way, if GDB does not change the PC, everything is as before.
If GDB *does* change the PC, execution will simply continue there --
and once GDB restores the PC it saved at that point, it will automatically
point to the *restarted* system call. (There is the minor twist how to
handle system calls that do *not* need restarting -- do_signal will undo
the PC change in this case, after get_signal_to_deliver has returned, and
only if ptrace did not change the PC during that call.)
Because there does not appear to be any obvious register to carry the
syscall-restart information on ARM, we'd either have to introduce a new
artificial ptrace register just for that purpose, or else handle the issue
transparently like on s390. The patch below implements the second option;
using this patch makes the interrupt.exp test cases pass on ARM, with no
regression in the GDB test suite otherwise.
Cc: patches@linaro.org
Signed-off-by: Ulrich Weigand <ulrich.weigand@linaro.org>
Signed-off-by: Arnd Bergmann <arnd.bergmann@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch allows the provided CONFIG_CMDLINE to be concatenated
with the one provided by the boot loader. This is useful to
merge the static values defined in CONFIG_CMDLINE with the
boot loader's (possibly) more dynamic values, such as startup
reasons and more.
Signed-off-by: Victor Boivie <victor.boivie@sonyericsson.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@sonyericsson.com>
Signed-off-by: Oskar Andero <oskar.andero@sonyericsson.com>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add some basic empty infrastructure for DT support on ARM.
v5: - Fix off-by-one error in size calculation of initrd
- Stop mucking with cmd_line, and load command line from dt into
boot_command_line instead which matches the behaviour of ATAGS booting
v3: - moved cmd_line export and initrd setup to this patch to make the
series bisectable.
- switched to alloc_bootmem_align() for allocation when
unflattening the device tree. memblock_alloc() was not the
right interface.
Signed-off-by: Jeremy Kerr <jeremy.kerr@canonical.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The dtb is passed to the kernel via register r2, which is the same
method that is used to pass an atags pointer. This patch modifies
__vet_atags to not clear r2 when it encounters a dtb image.
v2: fixed bugs pointed out by Nicolas Pitre
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
When CONFIG_OABI_COMPAT is set, the wrapper for semtimedop does not
bound the nsops argument. A sufficiently large value will cause an
integer overflow in allocation size, followed by copying too much data
into the allocated buffer. Fix this by restricting nsops to SEMOPM.
Untested.
Cc: stable@kernel.org
Signed-off-by: Dan Rosenberg <drosenberg@vsecurity.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
- Remove coding standard violations reported by checkpatch.pl
- Delete comment about handling of conditional branches which is no
longer true.
- Delete comment at end of file which lists all ARM instructions. This
duplicates data available in the ARM ARM and seems like an
unnecessary maintenance burden to keep this up to date and accurate.
Signed-off-by: Jon Medhurst <tixy@yxit.co.uk>
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Being able to probe NOP instructions is useful for hard-coding probeable
locations and is used by the kprobes test code.
Signed-off-by: Jon Medhurst <tixy@yxit.co.uk>
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
These bit field manipulation instructions occur several thousand
times in an ARMv7 kernel.
Signed-off-by: Jon Medhurst <tixy@yxit.co.uk>
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
The MOVW and MOVT instructions account for approximately 7% of all
instructions in a ARMv7 kernel as GCC uses them instead of a literal
pool.
Signed-off-by: Jon Medhurst <tixy@yxit.co.uk>
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
The instruction decoding in space_cccc_000x needs to reject probing of
instructions with undefined patterns as they may in future become
defined and then emulated faultily - as has already happened with the
SMC instruction.
This fix is achieved by testing for the instruction patterns we want to
probe and making the the default fall-through paths reject probes. This
also allows us to remove some explicit tests for instructions that we
wish to reject, as that is now the default action.
Signed-off-by: Jon Medhurst <tixy@yxit.co.uk>
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
The tests to explicitly reject probing CPS, RFE and SRS instructions
are redundant as the default case is now to reject undecoded patterns.
Signed-off-by: Jon Medhurst <tixy@yxit.co.uk>
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
The PLD instructions wasn't being decoded correctly and the emulation
code wasn't adjusting PC correctly.
As the PLD instruction is only a performance hint we emulate it as a
simple nop, and we can broaden the instruction decoding to take into
account newer PLI and PLDW instructions.
Signed-off-by: Jon Medhurst <tixy@yxit.co.uk>
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
The emulation of SETEND was broken as it changed the endianess for
the running kprobes handling code. Rather than adding a new simulation
routine to fix this we'll just reject probing of SETEND as these should
be very rare in the kernel.
Note, the function emulate_none is now unused but it is left in the
source code as future patches will use it.
Signed-off-by: Jon Medhurst <tixy@yxit.co.uk>
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Following the change to remove support for coprocessor instructions
we are left with three stub functions which can be consolidated.
Signed-off-by: Jon Medhurst <tixy@yxit.co.uk>
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
The kernel doesn't currently support VFP or Neon code, and probing of
code with CP15 operations is fraught with bad consequences. Therefore we
don't need the ability to probe coprocessor instructions and the code to
support this can be removed.
The removed code also had at least two bugs:
- MRC into R15 should set CPSR not trash PC
- LDC and STC which use PC as base register needed the address offset by 8
Signed-off-by: Jon Medhurst <tixy@yxit.co.uk>
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
The USAD8 instruction wasn't being explicitly decoded leading
to the incorrect emulation routine being called. It can be correctly
decoded in the same way as the signed multiply instructions so we move
the decoding there.
Signed-off-by: Jon Medhurst <tixy@yxit.co.uk>
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
The signed multiply instructions were being decoded incorrectly.
Signed-off-by: Jon Medhurst <tixy@yxit.co.uk>
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
These sign extension instructions are encoded as extend-and-add
instructions where the register to add is specified as r15. The decoding
routines weren't checking for this and were using the incorrect
emulation code, giving incorrect results.
Signed-off-by: Jon Medhurst <tixy@yxit.co.uk>
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
The instructions space for media instructions contains some undefined
patterns. We need to reject probing of these because they may in future
become defined and the kprobes code may then emulate them faultily.
Signed-off-by: Jon Medhurst <tixy@yxit.co.uk>
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
The v6T2 RBIT instruction was accidentally being emulated correctly,
this patch adds correct decoding for the instruction.
Signed-off-by: Jon Medhurst <tixy@yxit.co.uk>
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
These instructions are specified as UNPREDICTABLE.
Signed-off-by: Jon Medhurst <tixy@yxit.co.uk>
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
The decoding of these instructions got the register indexed and
immediate indexed forms the wrong way around, causing incorrect
emulation.
Instructions like "LDRD Rx, [Rx]" were corrupting Rx because the base
register writeback was being performed unconditionally, overwriting the
value just loaded from memory. The fix is to only writeback the base
register when that form of the instruction is used. Note, now that we
reject probing writeback with PC the emulation code doesn't need the
check rn!=15.
Signed-off-by: Jon Medhurst <tixy@yxit.co.uk>
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Using PC as an base register with writeback is UNPREDICTABLE, as is non
word-sized loads or stores of PC. (We only really care about preventing
loads to PC but it keeps the code simpler if we also exclude stores.)
Signed-off-by: Jon Medhurst <tixy@yxit.co.uk>
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
The decoding of these instructions got the register indexed and
immediate indexed forms the wrong way around, causing incorrect
emulation.
Signed-off-by: Jon Medhurst <tixy@yxit.co.uk>
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
The emulation code for STREX and LDREX instructions is faulty, however,
rather than attempting to fix this we reject probes of these
instructions. We do this because they can never succeed in gaining
exclusive access as the exception framework clears the exclusivity
monitor when a probes breakpoint is hit. (This is a general problem
when probing all instructions executing between a LDREX and its
corresponding STREX and can lead to infinite retry loops.)
Signed-off-by: Jon Medhurst <tixy@yxit.co.uk>
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
The instructions space for 'Multiply and multiply-accumulate'
instructions contains some undefined patterns. We need to reject
probing of these because they may in future become defined and the
kprobes code may then emulate them faultily.
This has already happened with the new MLS instruction which this patch
also adds correct decoding for as well as tightening up other decoding
tests. (Before this patch the wrong emulation routine was being called
for MLS though it still produced correct results.)
Signed-off-by: Jon Medhurst <tixy@yxit.co.uk>
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
The MRS instruction should set mode and interrupt bits in the read value
so it is simpler to use a new simulation routine (simulate_mrs) rather
than some modified emulation.
prep_emulate_rd12 is now unused and removed.
Signed-off-by: Jon Medhurst <tixy@yxit.co.uk>
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
We need to reject probing of instructions which read SPSR because
we can't handle this as the value in SPSR is lost when the exception
handler for the probe breakpoint first runs.
This patch also fixes the bitmask for MRS instructions decoding to
include checking bits 5-7.
Signed-off-by: Jon Medhurst <tixy@yxit.co.uk>
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Emulation of instructions like "ADD rd, rn, #<const>" would result in a
corrupted value for rd.
Signed-off-by: Jon Medhurst <tixy@yxit.co.uk>
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Probing these instructions was corrupting R0 because the emulation code
didn't account for the fact that they don't write a result to a
register.
Signed-off-by: Jon Medhurst <tixy@yxit.co.uk>
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Now we have the framework code handling conditionally executed
instructions we can remove redundant checks in individual simulation
routines.
Signed-off-by: Jon Medhurst <tixy@yxit.co.uk>
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
When a kprobe is placed onto conditionally executed ARM instructions,
many of the emulation routines used to single step them produce corrupt
register results. Rather than fix all of these cases we modify the
framework which calls them to test the relevant condition flags and, if
the test fails, skip calling the emulation code.
Signed-off-by: Jon Medhurst <tixy@yxit.co.uk>
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Currently emulate_ldrd and emulate_strd don't even have the adjustment
of the PC value, so in case of Rn == PC, it will not update the PC
incorrectly but instead load/store from the wrong address. Let's add
both the adjustment of the PC value and the check for PC == PC.
Signed-off-by: Viktor Rosendahl <viktor.rosendahl@nokia.com>
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
This function is only called by percpu_timer_setup() which is
also __cpuinit marked. Thus it's safe to mark this function as
__cpuinit as well.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The ARM user backtrace code can get into an infinite loop if it
runs into an invalid stack frame which points back to itself.
This situation has been observed in practice. Fix it by capping
the number of entries in the backtrace. This is also what other
architectures do in their backtrace code.
Signed-off-by: Sonny Rao <sonnyrao@chromium.org>
Acked-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
While the tracer accesses ptrace breakpoints, the child task may
concurrently exit due to a SIGKILL and thus release its breakpoints
at the same time. We can then dereference some freed pointers.
To fix this, hold a reference on the child breakpoints before
manipulating them.
Reported-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Prasad <prasad@linux.vnet.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Link: http://lkml.kernel.org/r/1302284067-7860-5-git-send-email-fweisbec@gmail.com
Convert some ARM architecture's common code to using
struct syscore_ops objects for power management instead of sysdev
classes and sysdevs.
This simplifies the code and reduces the kernel's memory footprint.
It also is necessary for removing sysdevs from the kernel entirely in
the future.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
There are optional bits that may complement a personality ID. It is
therefore wrong to simply test against the absolute current->personality
value to determine the effective personality. The PER_LINUX_32BIT is
itself just PER_LINUX with one of those optional bits set.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Our SET_PERSONALITY() implementation was overwriting all existing
personality flags, including ADDR_NO_RANDOMIZE, making them unavailable
to processes being exec'd after a call to personality() in user space.
This prevents the gdb test suite from running successfully.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
For future rework of try_to_wake_up() we'd like to push part of that
function onto the CPU the task is actually going to run on.
In order to do so we need a generic callback from the existing scheduler IPI.
This patch introduces such a generic callback: scheduler_ipi() and
implements it as a NOP.
BenH notes: PowerPC might use this IPI on offline CPUs under rare conditions!
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Acked-by: Chris Metcalf <cmetcalf@tilera.com>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Reviewed-by: Frank Rowand <frank.rowand@am.sony.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Nick Piggin <npiggin@kernel.dk>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/20110405152728.744338123@chello.nl
This patch adds THREAD_NOTIFY_COPY for calling registered handlers
during the copy_thread() function call. It also changes the VFP handler
to use a switch statement rather than if..else and ignore this event.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit a737823d ("ARM: perf: ensure overflows aren't missed due to IRQ
latency") changed the way that event deltas are calculated on overflow
so that we don't miss events when the new count value overtakes the
previous one.
Unfortunately, we forget to count the event that passes through zero so
we end up being off by 1. This patch adds on the correction.
Reported-by: Chris Moore <moore@free.fr>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The DBGVCR, used for configuring vector catch debug events, is UNKNOWN
out of reset on ARMv7. When enabling monitor mode, this must be zeroed
to avoid UNPREDICTABLE behaviour.
This patch adds the zeroing code to the debug reset path.
Cc: stable <stable@kernel.org>
Reported-by: Stepan Moskovchenko <stepanm@codeaurora.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
CONFIG_PM is now set whenever we support either runtime PM in addition
to suspend and hibernate. This causes build errors when runtime PM is
enabled on a platform, but the CPU does not have the appropriate support
for suspend.
So, switch this code to use CONFIG_PM_SLEEP rather than CONFIG_PM to
allow runtime PM to be enabled without causing build errors.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Use the proper accessor function instead of fiddling in the status
bits directly.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-arm-kernel@lists.infradead.org
The inline assembly differences for v6 vs. v7 are purely
optimizations. On a v7 processor, an mrc with the pc sets the
condition codes to the 28-31 bits of the register being read. It
just so happens that the TX/RX full bits the DCC support code is
testing for are high enough in the register to be put into the
condition codes. On a v6 processor, this "feature" isn't
implemented and thus we have to do the usual read, mask, test
operations to check for TX/RX full. Thus, we can drop the v7
implementation and just use the v6 implementation for both.
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The patch fixes the warning below:
WARNING: arch/arm/kernel/built-in.o(.data+0x27c): Section mismatch in reference from the variable etb_driver to the function .init.text:etb_probe()
The variable etb_driver references
the function __init etb_probe()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,
WARNING: arch/arm/kernel/built-in.o(.data+0x2cc): Section mismatch in reference from the variable etm_driver to the function .init.text:etm_probe()
The variable etm_driver references
the function __init etm_probe()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The PrPMC1100 machine was removed in 2.6.11, but left a reference to machine_is_prpmc1100 in arch/arm/kernel/bios32.c. 6f82f4db80 removed the machine type, which causes a build failure:
CC arch/arm/kernel/bios32.o
arch/arm/kernel/bios32.c: In function 'pci_fixup_prpmc1100':
arch/arm/kernel/bios32.c:174: error: implicit declaration of function 'machine_is_prpmc1100'
Remove the unused pci_fixup_prpcm1100.
Signed-off-by: Colin Cross <ccross@android.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The Rn value from the emulation is unconditionally written back;
this is fine as long as Rn != PC because in that case, even if the
instruction isn't a write back instruction, it will only result in the
same value being written back.
In case Rn == PC, then the emulated instruction doesn't have the
actual PC value in Rn but an adjusted value; when this is written
back, it will result in the PC being incorrectly updated.
An altenative solution would be to check bits 24 and 22 to see whether
the instruction actually is a write back instruction or not. I think
it's enough to check whether Rn != PC, because:
- it's looks cheaper than the alternative
- to my understaning it's not permitted to update the PC with a write
back instruction, so we don't lose any ability to emulate legal
instructions.
- in case of writing back for non write back instructions where Rn != PC, it doesn't matter because the values are the same.
Regarding the second point above, it would possibly be prudent to add
some checking to prep_emulate_ldr_str(), so that instructions with
both write back and Rn == PC would be rejected.
Signed-off-by: Viktor Rosendahl <viktor.rosendahl@nokia.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
If a counter overflows during a perf stat profiling run it may overtake
the last known value of the counter:
0 prev new 0xffffffff
|----------|-------|----------------------|
In this case, the number of events that have occurred is
(0xffffffff - prev) + new. Unfortunately, the event update code will
not realise an overflow has occurred and will instead report the event
delta as (new - prev) which may be considerably smaller than the real
count.
This patch adds an extra argument to armpmu_event_update which indicates
whether or not an overflow has occurred. If an overflow has occurred
then we use the maximum period of the counter to calculate the elapsed
events.
Acked-by: Jamie Iles <jamie@jamieiles.com>
Reported-by: Ashwin Chaugule <ashwinc@codeaurora.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
ARMv7 dictates that the interrupt-enable and count-enable registers for
each PMU counter are UNKNOWN following core reset.
This patch adds a new (optional) function pointer to struct arm_pmu for
resetting the PMU state during init. The reset function is called on
each CPU via an arch_initcall in the generic ARM perf_event code and
allows the PMU backend to write sane values to any UNKNOWN registers.
Acked-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The ARMv7 architecture does not guarantee that effects from co-processor
writes are immediately visible to following instructions.
This patch adds two isbs to the ARMv7 perf code:
(1) Immediately after selecting an event register, so that the PMU state
following this instruction is consistent with the new event.
(2) Immediately before writing to the PMCR, so that any previous writes
to the PMU have taken effect before (typically) enabling the
counters.
Acked-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Reviewed-by: Dave Martin <dave.martin@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Percpu allocator honors alignment request upto PAGE_SIZE and both the
percpu addresses in the percpu address space and the translated kernel
addresses should be aligned accordingly. The calculation of the
former depends on the alignment of percpu output section in the kernel
image.
The linker script macros PERCPU_VADDR() and PERCPU() are used to
define this output section and the latter takes @align parameter.
Several architectures are using @align smaller than PAGE_SIZE breaking
percpu memory alignment.
This patch removes @align parameter from PERCPU(), renames it to
PERCPU_SECTION() and makes it always align to PAGE_SIZE. While at it,
add PCPU_SETUP_BUG_ON() checks such that alignment problems are
reliably detected and remove percpu alignment comment recently added
in workqueue.c as the condition would trigger BUG way before reaching
there.
For um, this patch raises the alignment of percpu area. As the area
is in .init, there shouldn't be any noticeable difference.
This problem was discovered by David Howells while debugging boot
failure on mn10300.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Cc: uclinux-dist-devel@blackfin.uclinux.org
Cc: David Howells <dhowells@redhat.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: user-mode-linux-devel@lists.sourceforge.net
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (35 commits)
ARM: Update (and cut down) mach-types
ARM: 6771/1: vexpress: add support for multiple core tiles
ARM: 6797/1: hw_breakpoint: Fix newlines in WARNings
ARM: 6751/1: vexpress: select applicable errata workarounds in Kconfig
ARM: 6753/1: omap4: Enable ARM local timers with OMAP4430 es1.0 exception
ARM: 6759/1: smp: Select local timers vs broadcast timer support runtime
ARM: pgtable: add pud-level code
ARM: 6673/1: LPAE: use phys_addr_t instead of unsigned long for start of membanks
ARM: Use long long format when printing meminfo physical addresses
ARM: integrator: add Integrator/CP sched_clock support
ARM: realview/vexpress: consolidate SMP bringup code
ARM: realview/vexpress: consolidate localtimer support
ARM: integrator/versatile: consolidate FPGA IRQ handling code
ARM: rationalize versatile family Kconfig/Makefile
ARM: realview: remove old AMBA device DMA definitions
ARM: versatile: remove old AMBA device DMA definitions
ARM: vexpress: use new init_early for clock tree and sched_clock init
ARM: realview: use new init_early for clock tree and sched_clock init
ARM: versatile: use new init_early for clock tree and sched_clock init
ARM: integrator: use new init_early for clock tree init
...
The Xen PV drivers in a crashed HVM guest can not connect to the dom0
backend drivers because both frontend and backend drivers are still in
connected state. To run the connection reset function only in case of a
crashdump, the is_kdump_kernel() function needs to be available for the PV
driver modules.
Consolidate elfcorehdr_addr, setup_elfcorehdr and saved_max_pfn into
kernel/crash_dump.c Also export elfcorehdr_addr to make is_kdump_kernel()
usable for modules.
Leave 'elfcorehdr' as early_param(). This changes powerpc from __setup()
to early_param(). It adds an address range check from x86 also on ia64
and powerpc.
[akpm@linux-foundation.org: additional #includes]
[akpm@linux-foundation.org: remove elfcorehdr_addr export]
[akpm@linux-foundation.org: fix for Tejun's mm/nobootmem.c changes]
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'devel-stable' of master.kernel.org:/home/rmk/linux-2.6-arm: (289 commits)
davinci: DM644x EVM: register MUSB device earlier
davinci: add spi devices on tnetv107x evm
davinci: add ssp config for tnetv107x evm board
davinci: add tnetv107x ssp platform device
spi: add ti-ssp spi master driver
mfd: add driver for sequencer serial port
ARM: EXYNOS4: Implement Clock gating for System MMU
ARM: EXYNOS4: Enhancement of System MMU driver
ARM: EXYNOS4: Add support for gpio interrupts
ARM: S5P: Add function to register gpio interrupt bank data
ARM: S5P: Cleanup S5P gpio interrupt code
ARM: EXYNOS4: Add missing GPYx banks
ARM: S3C64XX: Fix section mismatch from cpufreq init
ARM: EXYNOS4: Add keypad device to the SMDKV310
ARM: EXYNOS4: Update clocks for keypad
ARM: EXYNOS4: Update keypad base address
ARM: EXYNOS4: Add keypad device helpers
ARM: EXYNOS4: Add support for SATA on ARMLEX4210
plat-nomadik: make GPIO interrupts work with cpuidle ApSleep
mach-u300: define a dummy filter function for coh901318
...
Fix up various conflicts in
- arch/arm/mach-exynos4/cpufreq.c
- arch/arm/mach-mxs/gpio.c
- drivers/net/Kconfig
- drivers/tty/serial/Kconfig
- drivers/tty/serial/Makefile
- drivers/usb/gadget/fsl_mxc_udc.c
- drivers/video/Kconfig
* 'defcfg' of master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: 6647/1: add Versatile Express defconfig
ARM: 6644/1: mach-ux500: update the U8500 defconfig
* 'drivers' of master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: 6764/1: pl011: factor out FIFO to TTY code
ARM: 6763/1: pl011: add optional RX DMA to PL011 v2
ARM: 6758/1: amba: support pm ops
ARM: amba: make amba_driver id_table const
ARM: amba: make internal ID table handling const
ARM: amba: make probe() functions take const id tables
ARM: 6662/1: amba: make amba_bustype non-static
ARM: mmci: add dmaengine-based DMA support
ARM: mmci: no need for separate host->data_xfered
ARM: mmci: avoid unnecessary switch to data available PIO interrupts
ARM: mmci: no need to call flush_dcache_page() with sg_miter API
ARM: mmci: avoid reporting too many completed bytes on fifo overrun
ALSA: AACI: make fifo variables more explanitory
ALSA: AACI: no need to call snd_pcm_period_elapsed() for each period
ALSA: AACI: use snd_pcm_lib_period_bytes()
ALSA: AACI: clean up AACI announcement printk
ALSA: AACI: fix channel mask selection
ALSA: AACI: fix number of channels for record
ALSA: AACI: fix multiple IRQ claiming
* 'cyberpro-next' of master.kernel.org:/home/rmk/linux-2.6-arm:
VIDEO: cyberpro: remove unused cyber2000fb_get_fb_var()
VIDEO: cyberpro: remove useless function extreg pointers
VIDEO: cyberpro: update handling of device structures
VIDEO: cyberpro: add support for video capture I2C
VIDEO: cyberpro: make 'reg_b0_lock' always present
VIDEO: cyberpro: add I2C support
VIDEO: cyberpro: select lowest multipler/divisor for PLL
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (91 commits)
ARM: 6806/1: irq: introduce entry and exit functions for chained handlers
ARM: 6781/1: Thumb-2: Work around buggy Thumb-2 short branch relocations in gas
ARM: 6747/1: P2V: Thumb2 support
ARM: 6798/1: aout-core: zero thread debug registers in a.out core dump
ARM: 6796/1: Footbridge: Fix I/O mappings for NOMMU mode
ARM: 6784/1: errata: no automatic Store Buffer drain on Cortex-A9
ARM: 6772/1: errata: possible fault MMU translations following an ASID switch
ARM: 6776/1: mach-ux500: activate fix for errata 753970
ARM: 6794/1: SPEAr: Append UL to device address macros.
ARM: 6793/1: SPEAr: Remove unused *_SIZE macros from spear*.h files
ARM: 6792/1: SPEAr: Replace SIZE macro's with SZ_4K macros
ARM: 6791/1: SPEAr3xx: Declare device structures after shirq code
ARM: 6790/1: SPEAr: Clock Framework: Rename usbd clock and align apb_clk entry
ARM: 6789/1: SPEAr3xx: Rename sdio to sdhci
ARM: 6788/1: SPEAr: Include mach/hardware.h instead of mach/spear.h
ARM: 6787/1: SPEAr: Reorder #includes in .h & .c files.
ARM: 6681/1: SPEAr: add debugfs support to clk API
ARM: 6703/1: SPEAr: update clk API support
ARM: 6679/1: SPEAr: make clk API functions more generic
ARM: 6737/1: SPEAr: formalized timer support
...
Will Deacon