dm-mpath.c needs to use a private workqueue (like other dm targets already do)
to avoid interfering with users of the default workqueue.
Signed-Off-By: Alasdair G Kergon <agk@redhat.com>
Acked-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Lars Marowsky-Bree <lmb@suse.de>
Signed-off-by: <mikenc@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Allow freeze_bdev() to return an error.
Signed-Off-By: Alasdair G Kergon <agk@redhat.com>
From: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make __unlock_fs() void.
From: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Store the struct block_device while device is frozen, saving us one call to
bdget_disk().
Signed-Off-By: Alasdair G Kergon <agk@redhat.com>
From: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This had a fatal lock ranking bug: we do journal_start outside
mpage_writepages()'s lock_page().
Revert the whole thing, think again.
Credit-to: Jan Kara <jack@suse.cz>
For identifying the bug.
Cc: Badari Pulavarty <pbadari@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add mailing list addresses for Orinoco and update its homepage.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Cc: David Gibson <hermes@gibson.dropbear.id.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Attached is a patch to bttv which fixes the following problems.
Affected cards and problems:
~~~~~~~~~~~~~~~~~~~~~~~~
o VP-1020 (200103A) Tuning problems, device detection.
o VP-1020 (DST-MOT) Errors during tuning, device detection fails in a while.
o VP-1030 (DST-CI) Tuning sometimes fails after CI commands.
o VP-2031 (DCT-CI) Tuning problems
The timeout happens before the actual timeout occured in the MCU
on the board, and hence the problems.
Changes: (bttv-i2c.diff)
~~~~~~~~~~~~~~~~~~~~~~~~
o Changed the custom wait queue to wait_event_interruptible_timeout()
- Suggestion by Johannes Stezenbach.
o Fixed the wait queue timeout problem
- This fixes the timeout problem on various cards.
- This problem was visible as many
* Cannot tune to channels, when signal levels are very low.
* app_info does not work in some conditions for CI based cards
- Smaller values worked good for newer cards, but the older cards
suffered, settled down to the worst case values that could happen in any
eventuality.
Signed-off-by: Manu Abraham <manu@kromtek.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The only caller that ever sets it can call fsync_bdev itself easily. Also
update some comments.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds support for a new class of DAC960 controllers. It's based
on the GPLed idac320 driver from IBM for Linux 2.4.18. That driver is a
fork of the 2.4.18 version of DAC960 that adds support for this new type of
controllers (internally called "GEM Series"), that differ from other DAC960
V2 firmware controllers only in the register offsets and removes support
for all others.
This patch instead integrates support for these controllers into the DAC960
driver.
Thanks to Anders Norrbring for pointing me to the idac320 driver and
testing this patch.
No Signed-Off: line because all code is either copy & pasted from IBM's
idac320 driver or support for other controllers in the 2.6 DAC960 driver.
Note: the really odd formating matches the rest of the DAC960 driver.
Cc: Dave Olien <dmo@osdl.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make sure that if the INTRTIE bit is set both functions of the cardbus
bridge use the same IRQ before doing any probing...
[ yes i hate the TI bridges for the fact that they are very flexible
so that so many BIOS vendors get it wrong. ]
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Enable 32-bit memory windows on pd6729 PCI-PCMCIA bridges.
Signed-off-by: Jarkko Raja <jar@pcuf.fi>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch handles the VIDIOC_S_FMT and VIDIOC_G_FMT ioctls for the
saa6752hs.
As only 4 preset video formats are supported (SIF, 1/2D1, 2/3D1, D1), we
compute to which the asked resolution is the nearest and apply it.
Signed-off-by: Frederic Cand <frederic.cand@anevia.com>
Acked-by: Gerd Knorr <kraxel@bytesex.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Additions to the dontdiff list.
Signed-off-by: Matt Porter <mporter@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There's no longer a reason to document the obsolete BK usage.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
These three functions are referenced from the __devinitdata
sis5513_chipset.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It seems that the code responsible for this is in kernel/itimer.c:126:
p->signal->real_timer.expires = jiffies + interval;
add_timer(&p->signal->real_timer);
If you request an interval of, lets say 900 usecs, the interval given by
timeval_to_jiffies will be 1.
If you request this when we are half-way between two timer ticks, the
interval will only give 400 usecs.
If we want to guarantee that we never ever give intervals less than
requested, the simple solution would be to change that to:
p->signal->real_timer.expires = jiffies + interval + 1;
This however will produce pathological cases, like having a idle system
being requested 1 ms timeouts will give systematically 2 ms timeouts,
whereas currently it simply gives a few usecs less than 1 ms.
The complex (and more computationally expensive) solution would be to
check the gettimeofday time, and compute the correct number of jiffies.
This way, if we request a 300 usecs timer 200 usecs inside the timer
tick, we can wait just one tick, but not if we are 800 usecs inside the
tick. This would also mean that we would have to lock preemption during
these computations to avoid races, etc.
I've searched the archives but couldn't find this particular issue being
discussed before.
Attached is a patch to do the simple solution, in case anybody thinks
that it should be used.
Signed-Off-By: Paulo Marques <pmarques@grupopie.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The `last_bh' logic probably isn't worth much. In those situations where only
the front part of the page is being written out we will save some looping but
in the vastly more common case of an all-page writeout if just adds more code.
Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove all those get_bh()'s and put_bh()'s by extending lock_page() to cover
the troublesome regions.
(get_bh() and put_bh() happen every time whereas contention on a page's lock
in there happens basically never).
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When running
fsstress -v -d $DIR/tmp -n 1000 -p 1000 -l 2
on an ext2 filesystem with 1024 byte block size, on SMP i386 with 4096 byte
page size over loopback to an image file on a tmpfs filesystem, I would
very quickly hit
BUG_ON(!buffer_async_write(bh));
in fs/buffer.c:end_buffer_async_write
It seems that more than one request would be submitted for a given bh
at a time.
What would happen is the following:
2 threads doing __mpage_writepages on the same page.
Thread 1 - lock the page first, and enter __block_write_full_page.
Thread 1 - (eg.) mark_buffer_async_write on the first 2 buffers.
Thread 1 - set page writeback, unlock page.
Thread 2 - lock page, wait on page writeback
Thread 1 - submit_bh on the first 2 buffers.
=> both requests complete, none of the page buffers are async_write,
end_page_writeback is called.
Thread 2 - wakes up. enters __block_write_full_page.
Thread 2 - mark_buffer_async_write on (eg.) the last buffer
Thread 1 - finds the last buffer has async_write set, submit_bh on that.
Thread 2 - submit_bh on the last buffer.
=> oops.
So change __block_write_full_page to explicitly keep track of the last bh
we need to issue, so we don't touch anything after issuing the last
request.
Signed-off-by: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix a race where __block_prepare_write can leak out an in-flight read
against a bh if get_block returns an error. This can lead to the page
becoming unlocked while the buffer is locked and the read still in flight.
__mpage_writepage BUGs on this condition.
BUG sighted on a 2-way Itanium2 system with 16K PAGE_SIZE running
fsstress -v -d $DIR/tmp -n 1000 -p 1000 -l 2
where $DIR is a new ext2 filesystem with 4K blocks that is quite
small (causing get_block to fail often with -ENOSPC).
Signed-off-by: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
During a warm boot the device is in D3 and has troubles coming out of it.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add better support for (non-incremental) 2.6.x.y patches; If an ending
version number if not specified, the script automatically increments the
SUBLEVEL (x in 2.6.x.y) until no more patch files are found; however,
EXTRAVERSION (y in 2.6.x.y) is never automatically incremented but must be
specified fully.
patch-kernel does not normally support reverse patching, but does so when
applying EXTRAVERSION (x.y) patches, so that moving from 2.6.11.y to
2.6.11.z is easy and handled by the script (reverse 2.6.11.y and apply
2.6.11.z).
Signed-off-by: Randy Dunlap <rddunlap@osdl.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Allow registration of multiple kprobes at an address in an architecture
agnostic way. Corresponding handlers will be invoked in a sequence. But,
a kprobe and a jprobe can't (yet) co-exist at the same address.
Signed-off-by: Ananth N Mavinakayanahalli <amavin@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
kernel oops! when unregister_kprobe() is called on a non-registered
kprobe. This patch fixes the above problem by checking if the probe exists
before unregistering.
Signed-off-by: Prasanna S Panchamukhi <prasanna@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Kprobes could not handle the insertion of a probe on the ret/lret
instruction and used to oops after single stepping since kprobes was
modifying eip/rip incorrectly. Adjustment of eip/rip is not required after
single stepping in case of ret/lret instruction, because eip/rip points to
the correct location after execution of the ret/lret instruction. This
patch fixes the above problem.
Signed-off-by: Prasanna S Panchamukhi <prasanna@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove some definitions and declarations from arch/um/include/skas_ptrace.h,
as they have moved to arch/um/include/sysdep/skas_ptrace.h
Also, remove PTRACE_SIGPENDING support in UML at all.
Signed-off-by: Bodo Stroesser <bstroesser@fujitsu-siemens.com>
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
UML: remove no longer needed arch-signal.h
Signed-off-by: Bodo Stroesser <bstroesser@fujitsu-siemens.com>
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
s390 passes parameters in registers. So the only safe way to find out the
address of signal context, error-address and error-type (trap_no), which are
passed to signal handlers as parameters, is to declare these parameters.
So I inserted an subarch-specific macro which holds the declaration of
parameters for signal handlers.
Signed-off-by: Bodo Stroesser <bstroesser@fujitsu-siemens.com>
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
s390 has fast read access to realtime clock (nanosecond resolution). So it
makes sense to have an arch-specific implementation not only of __delay, but
__udelay also.
Signed-off-by: Bodo Stroesser <bstroesser@fujitsu-siemens.com>
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Checksum handling largely depends on the subarch.
Thus, I renamed i386 arch_csum_partial in arch/um/sys-i386/checksum.S back to
csum_partial, removed csum_partial from arch/um/kernel/checksum.c and shifted
EXPORT_SYMBOL(csum_partial) to arch/um/sys-i386/ksyms.c.
Then, csum_partial_copy_to and csum_partial_copy_from were shifted from
arch/um/kernel/checksum.c to arch/um/include/sysdep-i386/checksum.h and
inserted in the calling functions csum_partial_copy_from_user() and
csum_and_copy_to_user().
Now, arch/um/kernel/checksum.c is empty and removed.
Signed-off-by: Bodo Stroesser <bstroesser@fujitsu-siemens.com>
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch replaces the contents of include/asm-um/linkage.h
by
#include "asm/arch/linkage.h"
Signed-off-by: Bodo Stroesser <bstroesser@fujitsu-siemens.com>
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch make elh.h a symlink to the new arch-specific include files of the
form elf-<subarch>.h, as in the same way already is done for some other
includes. Also moves Elf-stuff from archparam-<subarch>.h and elf.h to the
new elf-<subarch>.h files.
Signed-off-by: Bodo Stroesser <bstroesser@fujitsu-siemens.com>
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This cleans up the error handling and fixes a crash if a hostfs mount fails.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The completion cleanup got rid of some semaphores, but didn't remove the
inclusion of asm/semaphore.h from xterm_kern.c.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Just some breaking of some overly-long lines.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This makes SIGWINCH work again, and fixes a couple of SIGWINCH-associated
crashes. First, the sigio thread disables SIGWINCH because all hell breaks
loose if it ever gets one and tries to call the signal handling code. Second,
there was a problem with deferencing tty structs after they were freed. The
SIGWINCH support for a tty wasn't being turned off or freed after the tty went
away.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch removes the arch-specific fault/trap-infos from thread and
skas-regs.
It adds a new struct faultinfo, that is arch-specific defined in
sysdep/faultinfo.h.
The structure is inserted in thread.arch and thread.regs.skas and
thread.regs.tt
Now, segv and other trap-handlers can copy the contents from regs.X.faultinfo
to thread.arch.faultinfo with one simple assignment.
Also, the number of macros necessary is reduced to
FAULT_ADDRESS(struct faultinfo)
extracts the faulting address from faultinfo
FAULT_WRITE(struct faultinfo)
extracts the "is_write" flag
SEGV_IS_FIXABLE(struct faultinfo)
is true for the fixable segvs, i.e. (TRAP == 14)
on i386
UPT_FAULTINFO(regs)
result is (struct faultinfo *) to the faultinfo
in regs->skas.faultinfo
GET_FAULTINFO_FROM_SC(struct faultinfo, struct sigcontext *)
copies the relevant parts of the sigcontext to
struct faultinfo.
On SIGSEGV, call user_signal() instead of handle_segv(), if the architecture
provides the information needed in PTRACE_FAULTINFO, or if PTRACE_FAULTINFO is
missing, because segv-stub will provide the info.
The benefit of the change is, that in case of a non-fixable SIGSEGV, we can
give user processes a SIGSEGV, instead of possibly looping on pagefault
handling.
Since handle_segv() sikked arch_fixup() implicitly by passing ip==0 to segv(),
I changed segv() to call arch_fixup() only, if !is_user.
Signed-off-by: Bodo Stroesser <bstroesser@fujitsu-siemens.com>
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This fixes write_ldt_entry to treat userspace_pid as an array.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
O=... builds support. Very easy, actually.
Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
make distclean et.al. are missing arch/um/sys-x86_64/utils; fixed the same
way we have it done for sys-i386 counterpart.
Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
helpers in arch/um/util (mk_task and mk_constants) converted. That's it -
none of the helpers depends on build and target being the same architecture
anymore.
Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
mk_thread converted
Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The next group of helpers is a bit trickier - they want the constants similar
to those in user-offsets.h, but we need target sc.h for it. So we can't put
that into user-offsets (sc.h depends on it) and need the second generated
header for that stuff (kernel-offsets.h. BFD...
Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Ditto for mk_sc
Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
mk_ptregs converted. Nothing new here, it's the same situation as with
mk_user_constants.
Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Beginning of cross-build fixes. Instead of expecting that mk_user_constants
(compiled and executed on the build box) will see the sizeof, etc. for target
box, we do what every architecture already does for asm-offsets. Namely, have
user-offsets.c compiled *for* *target* into user-offsets.s and sed it into the
header with relevant constants. We don't need to reinvent any wheels - all
tools are already there.
This patch deals with mk_user_constants. It doesn't assume any relationship
between target and build environment anymore - we pick all defines we need
from user-offsets.h. Later patches will deal with the rest of mk_... helpers
in the same way.
Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Alasdair G Kergon