This driver is only useful on MSM8x74, so let the driver depend on
ARCH_QCOM but allow compile coverage testing.
The main benefit is that the driver isn't available to be selected for
machines that don't have the matching hardware.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds pinctrl definitions for the GPIO pins of the TLMM v2 block in the
Qualcomm APQ8064 platform.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This lets the gpiolib core handle the irqchip set-up and
chained IRQ on the primary (behind the mux) IRQ chip in
the st pinctrl driver.
Default irq type is set to level low at irqchip add time.
The v1 was sent by Linus
(https://lkml.org/lkml/2014/4/4/287).
Two changes were necessary to make it to work properly
on STiH416:
1 - dev reference was not passed to the gpio_chip
struct, causing a panic.
2 - gpiochip_irqchip_add passed IRQ_TYPE_NONE as
default type, which caused lot of warnings at
init time. I choose IRQ_TYPE_LEVEL_LOW as default.
Cc: Srinivas Kandagatla <srinivas.kandagatla@gmail.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Maxime COQUELIN <maxime.coquelin@st.com>
To be consistent with other Broadcom drivers, the Broadcom Capri pinctrl
driver and its related CONFIG option are renamed to bcm281xx.
Devicetree compatible string and binding documentation use
"brcm,bcm11351-pinctrl" to match the machine binding here:
Documentation/devicetree/bindings/arm/bcm/bcm11351.txt
This driver supports pinctrl on BCM11130, BCM11140, BCM11351, BCM28145
and BCM28155 SoCs.
Signed-off-by: Sherman Yin <syin@broadcom.com>
Reviewed-by: Matt Porter <mporter@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- Merged in a branch of irqchip changes from Thomas
Gleixner: we need to have new callbacks from the
irqchip to determine if the GPIO line will be eligible
for IRQs, and this callback must be able to say "no".
After some thinking I got the branch from tglx and
have switched all current users over to use this.
- Based on tglx patches, we have added some generic
irqchip helpers in the gpiolib core. These will
help centralize code when GPIO drivers have simple
chained/cascaded IRQs. Drivers will still define
their irqchip vtables, but the gpiolib core will
take care of irqdomain set-up, mapping from local
offsets to Linux irqs, and reserve resources by
marking the GPIO lines for IRQs.
- Initially the PL061 and Nomadik GPIO/pin control
drivers have been switched over to use the new
gpiochip-to-irqchip infrastructure with more
drivers expected for the next kernel cycle. The
factoring of just two drivers still makes it worth
it so it is already a win.
- A new driver for the Synopsys DesignWare APB GPIO
block.
- Modify the DaVinci GPIO driver to be reusable also
for the new TI Keystone architecture.
- A new driver for the LSI ZEVIO SoCs.
- Delete the obsolte tnetv107x driver.
- Some incremental work on GPIO descriptors: have
gpiod_direction_output() use a logical level,
respecting assertion polarity through ACTIVE_LOW
flags, adding gpiod_direction_output_raw() for the
case where you want to set that very value. Add
gpiochip_get_desc() to fetch a GPIO descriptor from
a specific offset on a certain chip inside driver
code.
- Switch ACPI GPIO code over to using
gpiochip_get_desc() and get rid of gpio_to_desc().
- The ACPI GPIO event handling code has been reworked
after encountering an actual real life implementation.
- Support for ACPI GPIO operation regions.
- Generic GPIO chips can now be assigned labels/names
from platform data.
- We now clamp values returned from GPIO drivers to
the boolean [0,1] range.
- Some improved documentation on how to use the polarity
flag was added.
- The a large slew of incremental driver updates and
non-critical fixes. Some targeted for stable.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=8Qqf
-----END PGP SIGNATURE-----
Merge tag 'gpio-v3.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull bulk of gpio updates from Linus Walleij:
"A pretty big chunk of changes this time, but it has all been on
rotation in linux-next and had some testing. Of course there will be
some amount of fixes on top...
- Merged in a branch of irqchip changes from Thomas Gleixner: we need
to have new callbacks from the irqchip to determine if the GPIO
line will be eligible for IRQs, and this callback must be able to
say "no". After some thinking I got the branch from tglx and have
switched all current users over to use this.
- Based on tglx patches, we have added some generic irqchip helpers
in the gpiolib core. These will help centralize code when GPIO
drivers have simple chained/cascaded IRQs. Drivers will still
define their irqchip vtables, but the gpiolib core will take care
of irqdomain set-up, mapping from local offsets to Linux irqs, and
reserve resources by marking the GPIO lines for IRQs.
- Initially the PL061 and Nomadik GPIO/pin control drivers have been
switched over to use the new gpiochip-to-irqchip infrastructure
with more drivers expected for the next kernel cycle. The
factoring of just two drivers still makes it worth it so it is
already a win.
- A new driver for the Synopsys DesignWare APB GPIO block.
- Modify the DaVinci GPIO driver to be reusable also for the new TI
Keystone architecture.
- A new driver for the LSI ZEVIO SoCs.
- Delete the obsolte tnetv107x driver.
- Some incremental work on GPIO descriptors: have
gpiod_direction_output() use a logical level, respecting assertion
polarity through ACTIVE_LOW flags, adding gpiod_direction_output_raw()
for the case where you want to set that very value. Add
gpiochip_get_desc() to fetch a GPIO descriptor from a specific
offset on a certain chip inside driver code.
- Switch ACPI GPIO code over to using gpiochip_get_desc() and get rid
of gpio_to_desc().
- The ACPI GPIO event handling code has been reworked after
encountering an actual real life implementation.
- Support for ACPI GPIO operation regions.
- Generic GPIO chips can now be assigned labels/names from platform
data.
- We now clamp values returned from GPIO drivers to the boolean [0,1]
range.
- Some improved documentation on how to use the polarity flag was
added.
- a large slew of incremental driver updates and non-critical fixes.
Some targeted for stable"
* tag 'gpio-v3.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (80 commits)
gpio: rcar: Add helper variable dev = &pdev->dev
gpio-lynxpoint: force gpio_get() to return "1" and "0" only
gpio: unmap gpio irqs properly
pch_gpio: set value before enabling output direction
gpio: moxart: Actually set output state in moxart_gpio_direction_output()
gpio: moxart: Avoid forward declaration
gpio: mxs: Allow for recursive enable_irq_wake() call
gpio: samsung: Add missing "break" statement
gpio: twl4030: Remove redundant assignment
gpio: dwapb: correct gpio-cells in binding document
gpio: iop: fix devm_ioremap_resource() return value checking
pinctrl: coh901: convert driver to use gpiolib irqchip
pinctrl: nomadik: convert driver to use gpiolib irqchip
gpio: pl061: convert driver to use gpiolib irqchip
gpio: add IRQ chip helpers in gpiolib
pinctrl: nomadik: factor in platform data container
pinctrl: nomadik: rename secondary to latent
gpio: Driver for SYSCON-based GPIOs
gpio: generic: Use platform_device_id->driver_data field for driver flags
pinctrl: coh901: move irq line locking to resource callbacks
...
functionality this time, just incremental driver updates:
- A large refactoring of the MVEBU (Marvell) driver.
- A large refactoring of the Tegra (nVidia) driver.
- GPIO interrupt including soft edges support in the
STi driver.
- Misc updates to PFC (Renesas), AT91, ADI2 (Blackfin),
pinctrl-single, sirf (CSR), msm (Qualcomm), Exynos (Samsung),
sunxi (AllWinner), i.MX (Freescale), Baytrail.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=i7Sq
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v3.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control bulk changes from Linus Walleij:
"Pin control bulk changes for the v3.15 series, no new core
functionality this time, just incremental driver updates:
- A large refactoring of the MVEBU (Marvell) driver.
- A large refactoring of the Tegra (nVidia) driver.
- GPIO interrupt including soft edges support in the STi driver.
- Misc updates to PFC (Renesas), AT91, ADI2 (Blackfin),
pinctrl-single, sirf (CSR), msm (Qualcomm), Exynos (Samsung), sunxi
(AllWinner), i.MX (Freescale), Baytrail"
* tag 'pinctrl-v3.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (72 commits)
pinctrl: tegra: add some missing Tegra114 entries
pinctrl: tegra: fix some mistakes in Tegra124
pinctrl: msm: fix up out-of-order merge conflict
pinctrl: st: Fix error check for of_irq_to_resource usage
pinctrl: tegra: consistency cleanup
pinctrl: tegra: dynamically calculate function list of groups
pinctrl: tegra: init Tegra20/30 at module_init time
pinctrl: st: Use ARRAY_SIZE instead of raw value for number of delays
pinctrl: st: add pinctrl support for the STiH407 SoC
pinctrl: st: Enhance the controller to manage unavailable registers
pinctrl: msm: Simplify msm_config_reg() and callers
pinctrl: msm: Remove impossible WARN_ON()s
pinctrl: msm: Replace lookup tables with math
pinctrl: msm: Drop OF_IRQ dependency
pinctrl: msm: Drop unused includes
pinctrl: msm: Check for ngpios > MAX_NR_GPIO
pinctrl: msm: Silence recursive lockdep warning
pinctrl: mvebu: silence WARN to dev_warn
pinctrl: msm: drop wake_irqs bitmap
pinctrl-baytrail: add function mux checking in gpio pin request
...
This converts the COH901 pin control driver to register its
chained irq handler and irqchip using the helpers in the
gpiolib core.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This converts the Nomadik pin control driver to register its
chained irq handler and irqchip using the helpers in the
gpiolib core.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This driver doesn't rely on any functionality living in
drivers/of/irq.c to compile. Drop this dependency.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Modular builds of pinctrl-msm break due to handle_bad_irq being
unexported for module use. For now, make PINCTRL_MSM 'bool'.
Signed-off-by: Josh Cartwright <joshc@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As this driver is using pinconf_generic_dt_node_to_map_pin() it
needs to depend on OF so as not to cause build problems on
archs that do not support OF.
Cc: Sherman Yin <syin@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Adds pinctrl driver for Broadcom Capri (BCM281xx) SoCs.
v4: - PINCTRL selected in Kconfig, PINCTRL_CAPRI selected in bcm_defconfig
- make use of regmap
- change CAPRI_PIN_UPDATE from macro to inline function.
- Handle pull-up strength arg in Ohm instead of enum
v3: Re-work driver to be based on generic pin config. Moved config selection
from Kconfig to bcm_defconfig.
v2: Use hyphens instead of underscore in DT property names.
Signed-off-by: Sherman Yin <syin@broadcom.com>
Reviewed-by: Christian Daudt <bcm@fixthebug.org>
Reviewed-by: Matt Porter <matt.porter@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add GPIOLIB and OF as dependencies for PINCTRL_MSM8X74, to fix
build errors from i386-randconfig.
Also add help text and make the entries tristate, while touching
these entries.
Cc: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
[Rebased on top of pin control development branch]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds a driver for the Tegra124 pinmux, and required
parameterization data for Tegra124.
The driver uses the common Tegra pincontrol driver utility
functions to implement the majority of the driver.
This driver is not compatible with the earlier NVIDIA's SoCs,
hence add new compatibile as "nvidia,tegra124-pinmux".
Originally written by Ashwini Gguhe.
Thierry:
- Cleanups in patches.
ldewangan:
- Fix some entries for groups.
- Fix MUX enums and group sequence.
Signed-off-by: Ashwini Ghuge <aghuge@nvidia.com>
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
CC: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We had a compilation failure on x86_64 due to missing OF support
as this was an implicit dependency. Add an explicit dependency
on OF and OF_IRQ on the SoC driver.
Cc: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add initial definition of parameters for pinctrl-msm for the msm8x74
platform.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds a pinctrl, pinmux, pinconf and gpiolib driver for the
Qualcomm TLMM block.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This is mostly cut and paste from the imx35 pinctrl driver.
The data was generated using sed and awk on
arch/arm/plat-mxc/include/mach/iomux-mx25.h.
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: devicetree@vger.kernel.org
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Eric Bénard <eric@eukrea.com>
Signed-off-by: Denis Carikli <denis@eukrea.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The IMX/MXC selects USE_OF at architecture level, so the OF dependency
at individual SoC pinctrl driver level can just be dropped.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add code to support the specific pin arrangements of the Freescale IMX50 SoC.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
imx27 pincontrol driver using the imx1 core driver. The DT bindings are
similar to other imx pincontrol drivers.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Core driver for register formats of imx1/imx21/imx27 processors.
The pins of those processors are grouped into ports. Each port has 32
pins. The pins mux configuration is controlled by registers with 1 or 2
bit per pin, depending on the specific control register.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pinmux driver of the Abilis Systems TB10x platform based on ARC700 CPUs.
Used to control the pinmux and is a prerequisite for the GPIO driver.
Signed-off-by: Christian Ruppert <christian.ruppert@abilis.com>
Signed-off-by: Pierrick Hascoet <pierrick.hascoet@abilis.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The AS3722 is a compact system PMU suitable for mobile phones, tablets etc.
Add a driver to support accessing the GPIO, pinmux and pin configuration
of 8 GPIO pins found on the ams AS3722 through pin control driver and
gpiolib.
The driver will register itself as the pincontrol driver and gpio driver.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The new ADI GPIO2 controller was introduced since the BF548 and BF60x
processors. It differs a lot from the old one on BF5xx processors. So,
create a pinctrl driver under the pinctrl framework.
- Define gpio ports and pin interrupt controllers as individual platform
devices.
- Register a pinctrl driver for the whole GPIO ports and pin interrupt
devices.
- Probe pint devices before port devices. Put device instances into
the global gpio and pint lists.
- Define peripheral, irq and gpio reservation bit masks for each gpio
port as runtime resources.
- Save and restore gpio port and pint status MMRs in syscore PM functions.
- Create the plug-in subdrivers to hold the pinctrl soc data for bf54x
and bf60x. Add soc data into struct adi_pinctrl. Initialize the soc data
in pin controller probe function. Get the pin groups and functions via
the soc data reference.
- Call gpiochip_add_pin_range() in gpio device probe function to register
range cross reference between gpio device and pin control device.
- Get range by pinctrl_find_gpio_range_from_pin(), find gpio_port object
by container_of() and find adi_pinctrl by pin control device name.
- Handle peripheral and gpio requests in pinctrl operation functions.
- Demux gpio IRQs via the irq_domain created by each GPIO port.
v2-changes:
- Remove unlinke() directive.
v3-changes:
- Rename struct adi_pmx to adi_pinctrl.
- Fix the comments of struct gpio_pint.
- Remove unused pin_base in struct gpio_port.
- Change pint_assign into bool type.
- Add comments about the relationship between pint device and port device
to the driver header.
- Use BIT macro to shift bit.
- Remove all bitmap reservation help functions. Inline reservation functions
into the actual code.
- Remove gpio and offset mutual reference help functions.
- Remove all help functions to find gpio_port and adi_pinctrl structs. Get
range by pinctrl_find_gpio_range_from_pin(), find gpio_port object by
container_of() and find adi_pinctrl by pin control device name.
- Pass bool type usage variable to port_setup help function.
- Separate long bit operations into several lines and add comments.
- Use debugfs to output all GPIO request information.
- Avoid to set drvdata to NULL
- Add explanation to function adi_gpio_init_int()
- Call gpiochip_add_pin_range() in gpio device probe function to register
range cross reference between gpio device and pin control device.
- Remove the reference to pin control device from the gpio_port struct.
Remove the reference list to gpio device from the adi_pinctrl struct.
Replace the global adi_pinctrl list with adi_gpio_port_list. Walk through
the gpio list to do power suspend and resume operations.
- Remove the global GPIO base from struct adi_pinctrl, define pin base in
the platform data for each GPIO port device.
- Initialize adi_pinctrl_setup in arch_initcall().
- print the status of triggers, whether it is in GPIO mode, if it is
flagged to be used as IRQ, etc in adi_pin_dbg_show().
- Create the plug-in subdrivers to hold the pinctrl soc data for bf54x
and bf60x. Add soc data into struct adi_pinctrl. Initialize the soc data
in pin controller probe function. Get the pin groups and functions via
the soc data reference.
v4-changes:
- remove useless system_state checking.
- replace dev_err with dev_warn in both irq and gpio pin cases.
- comment on relationship between irq type and invert operation.
- It is not necessary to check the reservation mode of the requested
pin in IRQ chip operation. Remove the reservation map.
- Use existing gpio/pinctrl subsystem debugfs files. Remove pinctrl-adi2
driver specific debugfs output.
- Add linkport group and function information for bf60x.
- Separate uart and ctsrts pins into 2 groups.
- Separate APAPI and alternative ATAPI pins into 2 groups.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch implements pinctrl support and adds device tree bindings
for s5pv210.
Signed-off-by: Mateusz Krawczuk <m.krawczuk@partner.samsung.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix below build error if !PINMUX.
CC drivers/pinctrl/pinctrl-palmas.o
drivers/pinctrl/pinctrl-palmas.c:741:21: error: variable 'palmas_pinmux_ops' has initializer but incomplete type
drivers/pinctrl/pinctrl-palmas.c:742:2: error: unknown field 'get_functions_count' specified in initializer
drivers/pinctrl/pinctrl-palmas.c:742:2: warning: excess elements in struct initializer [enabled by default]
drivers/pinctrl/pinctrl-palmas.c:742:2: warning: (near initialization for 'palmas_pinmux_ops') [enabled by default]
drivers/pinctrl/pinctrl-palmas.c:743:2: error: unknown field 'get_function_name' specified in initializer
drivers/pinctrl/pinctrl-palmas.c:743:2: warning: excess elements in struct initializer [enabled by default]
drivers/pinctrl/pinctrl-palmas.c:743:2: warning: (near initialization for 'palmas_pinmux_ops') [enabled by default]
drivers/pinctrl/pinctrl-palmas.c:744:2: error: unknown field 'get_function_groups' specified in initializer
drivers/pinctrl/pinctrl-palmas.c:744:2: warning: excess elements in struct initializer [enabled by default]
drivers/pinctrl/pinctrl-palmas.c:744:2: warning: (near initialization for 'palmas_pinmux_ops') [enabled by default]
drivers/pinctrl/pinctrl-palmas.c:745:2: error: unknown field 'enable' specified in initializer
drivers/pinctrl/pinctrl-palmas.c:745:2: warning: excess elements in struct initializer [enabled by default]
drivers/pinctrl/pinctrl-palmas.c:745:2: warning: (near initialization for 'palmas_pinmux_ops') [enabled by default]
make[2]: *** [drivers/pinctrl/pinctrl-palmas.o] Error 1
make[1]: *** [drivers/pinctrl] Error 2
make: *** [drivers] Error 2
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The device family is called Palmas so there should be a 's' on the end of
the name.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
TI Palmas series Power Management IC have multiple pins which can be
configured for different functionality. This pins can be configured
for different function. Also their properties like pull up/down,
open drain enable/disable are configurable.
Add support for pincontrol driver Palmas series device like TPS65913,
TPS80036. The driver supports to be register from DT only.
Changes from V1:
- Add generic property for pins and functions in pinconf-generic.
- Add APIs to map the DT and subnode.
- Move common utils APIs to the pinctrl-utils from this file.
- Update the binding document accordingly.
Changes from V2:
- Add ack by Lee.
- Correct the binding docs.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There are two minor issues with indentation in the code. This patch fixes them.
No functional changes.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- A large slew of improvements of the Genric pin configuration
support, and deployment in four different platforms:
Rockchip, Super-H PFC, ABx500 and TZ1090. Support BIAS_BUS_HOLD,
get device tree parsing and debugfs support into shape.
- We also have device tree support with generic naming conventions
for the generic pin configuration.
- Delete the unused and confusing direct pinconf API. Now state
transitions is *the* way to control pins and multiplexing.
- New drivers for Rockchip, TZ1090, and TZ1090 PDC.
- Two pin control states related to power management are now
handled in the device core: "sleep" and "idle", removing a lot
of boilerplate code in drivers. We do not yet know if this is
the final word for pin PM, but it already make things a lot
easier to handle.
- Handle sparse GPIO ranges passing a list of disparate pins, and
utilize these in the new BayTrail (x86 Atom SoC) driver.
- Make the sunxi (AllWinner) driver handle external interrupts.
- Make it possible for pinctrl-single to handle the case where
several pins are managed by a single register, and augment it to
handle sleep modes.
- Cleanups and improvements for the abx500 drivers.
- Move Sirf pin control drivers to their own directory, support
save/restore of context and add support for the SiRFatlas6 SoC.
- PMU muxing for the Dove pinctrl driver.
- Finalization and support for VF610 in the i.MX6 pinctrl driver.
- Smoothen out various Exynos rough edges.
- Generic cleanups of various kinds.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=EbAf
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-for-v3.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control changes from Linus Walleij:
- A large slew of improvements of the Genric pin configuration support,
and deployment in four different platforms: Rockchip, Super-H PFC,
ABx500 and TZ1090. Support BIAS_BUS_HOLD, get device tree parsing
and debugfs support into shape.
- We also have device tree support with generic naming conventions for
the generic pin configuration.
- Delete the unused and confusing direct pinconf API. Now state
transitions is *the* way to control pins and multiplexing.
- New drivers for Rockchip, TZ1090, and TZ1090 PDC.
- Two pin control states related to power management are now handled in
the device core: "sleep" and "idle", removing a lot of boilerplate
code in drivers. We do not yet know if this is the final word for
pin PM, but it already make things a lot easier to handle.
- Handle sparse GPIO ranges passing a list of disparate pins, and
utilize these in the new BayTrail (x86 Atom SoC) driver.
- Make the sunxi (AllWinner) driver handle external interrupts.
- Make it possible for pinctrl-single to handle the case where several
pins are managed by a single register, and augment it to handle sleep
modes.
- Cleanups and improvements for the abx500 drivers.
- Move Sirf pin control drivers to their own directory, support
save/restore of context and add support for the SiRFatlas6 SoC.
- PMU muxing for the Dove pinctrl driver.
- Finalization and support for VF610 in the i.MX6 pinctrl driver.
- Smoothen out various Exynos rough edges.
- Generic cleanups of various kinds.
* tag 'pinctrl-for-v3.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (82 commits)
pinctrl: vt8500: wmt: remove redundant dev_err call in wmt_pinctrl_probe()
pinctrl: remove bindings for pinconf options needing more thought
pinctrl: remove slew-rate parameter from tz1090
pinctrl: set unit for debounce time pinconfig to usec
pinctrl: more clarifications for generic pull configs
pinctrl: rip out the direct pinconf API
pinctrl-tz1090-pdc: add TZ1090 PDC pinctrl driver
pinctrl-tz1090: add TZ1090 pinctrl driver
pinctrl: samsung: Staticize drvdata_list
pinctrl: rockchip: Add missing irq_gc_unlock() call before return error
pinctrl: abx500: rework error path
pinctrl: abx500: suppress hardcoded value
pinctrl: abx500: factorize code
pinctrl: abx500: fix abx500_gpio_get()
pinctrl: abx500: fix abx500_pin_config_set()
pinctrl: abx500: Add device tree support
sh-pfc: Guard DT parsing with #ifdef CONFIG_OF
pinctrl: add Intel BayTrail GPIO/pinctrl support
pinctrl: fix pinconf_ops::pin_config_dbg_parse_modify kerneldoc
pinctrl: Staticize local symbols
...
Conflicts:
drivers/net/ethernet/ti/davinci_mdio.c
drivers/pinctrl/Makefile
A small but useful set of regmap updates this time around:
- An abstraction for bitfields within a register map contributed by
Srinivas Kandagatla, allowing drivers to cope more easily when
hardware designers randomly move things about (mainly when talking
to things like system controllers).
- Changes from Lars-Peter Clausen to allow the MMIO regmap to be used from
hard IRQ context.
- Small improvements to the cache infrastructure and performance,
including a default cache sync operation so now all regmaps can sync
easily.
There's also a pinctrl driver making use of the new bitfield API, merged
here for dependency reasons. There will be a simple add/add conflict
with the pinctrl tree as a result.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=8WLH
-----END PGP SIGNATURE-----
Merge tag 'regmap-v3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap updates from Mark Brown:
"A small but useful set of regmap updates this time around:
- An abstraction for bitfields within a register map contributed by
Srinivas Kandagatla, allowing drivers to cope more easily when
hardware designers randomly move things about (mainly when talking
to things like system controllers).
- Changes from Lars-Peter Clausen to allow the MMIO regmap to be used
from hard IRQ context.
- Small improvements to the cache infrastructure and performance,
including a default cache sync operation so now all regmaps can
sync easily.
There's also a pinctrl driver making use of the new bitfield API,
merged here for dependency reasons. There will be a simple add/add
conflict with the pinctrl tree as a result."
* tag 'regmap-v3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
pinctrl: st: Remove unnecessary use of of_match_ptr macro
pinctrl: st: fix return value check
pinctrl: st: Add pinctrl and pinconf support.
regmap: debugfs: Suppress cache for partial register files
regmap: Add regmap_field APIs
regmap: core: Cache all registers by default when cache is enabled
regmap: Implemented default cache sync operation
regmap: Make regmap-mmio usable from atomic contexts
regmap: regcache: Fixup locking for custom lock callbacks
regmap: debugfs: Fix return from regmap_debugfs_get_dump_start
regmap: debugfs: Don't mark lockdep as broken due to debugfs write
regmap: rbtree: Use range information to allocate nodes
regmap: rbtree: Factor out node allocation
regmap: Make regmap_check_range_table() a public API
regmap: Add support for discarding parts of the register cache
These changes are all driver specific and cross over between arm-soc
contents and some other subsystem, in these cases cpufreq, crypto,
dma, pinctrl, mailbox and usb, and the subsystem owners agreed to
have these changes merged through arm-soc. As we proceed to untangle
the dependencies between platform code and driver code, the amount of
changes in this category is fortunately shrinking, for 3.11 we have
16 branches here and 101 non-merge changesets, the majority of which
are for the stedma40 dma engine driver used in the ux500 platform.
Cleaning up that code touches multiple subsystems, but gets rid
of the dependency in the end.
The mailbox code moved out from mach-omap2 to drivers/mailbox
is an intermediate step and is still omap specific at the moment.
Patches exist to generalize the subsystem and add other drivers
with the same API, but those did not make it for 3.11.
Conflicts:
* In cpu-db8500.c results from the removal of the u8500_of_init_devices
function in combination with the split of u8500_auxdata_lookup.
* In arch/arm/mach-omap2/devices.c, the includes got reshuffled.
we need to keep linux/wl12xx.h and linux/platform_data/mailbox-omap.h.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=mJsI
-----END PGP SIGNATURE-----
Merge tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver specific changes from Arnd Bergmann:
"These changes are all driver specific and cross over between arm-soc
contents and some other subsystem, in these cases cpufreq, crypto,
dma, pinctrl, mailbox and usb, and the subsystem owners agreed to have
these changes merged through arm-soc.
As we proceed to untangle the dependencies between platform code and
driver code, the amount of changes in this category is fortunately
shrinking, for 3.11 we have 16 branches here and 101 non-merge
changesets, the majority of which are for the stedma40 dma engine
driver used in the ux500 platform. Cleaning up that code touches
multiple subsystems, but gets rid of the dependency in the end.
The mailbox code moved out from mach-omap2 to drivers/mailbox is an
intermediate step and is still omap specific at the moment. Patches
exist to generalize the subsystem and add other drivers with the same
API, but those did not make it for 3.11."
* tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (101 commits)
crypto: ux500: use dmaengine_submit API
crypto: ux500: use dmaengine_prep_slave_sg API
crypto: ux500: use dmaengine_device_control API
crypto: ux500/crypt: add missing __iomem qualifiers
crypto: ux500/hash: add missing static qualifiers
crypto: ux500/hash: use readl on iomem addresses
dmaengine: ste_dma40: Declare memcpy config as static
ARM: ux500: Remove mop500_snowball_ethernet_clock_enable()
ARM: ux500: Correct the EN_3v3 regulator's on/off GPIO
ARM: ux500: Provide a AB8500 GPIO Device Tree node
gpio: rcar: fix gpio_rcar_of_table
gpio-rcar: Remove #ifdef CONFIG_OF around OF-specific sections
gpio-rcar: Reference core gpio documentation in the DT bindings
clk: exynos5250: Add enum entries for divider clock of i2s1 and i2s2
ARM: dts: Update Samsung I2S documentation
ARM: dts: add clock provider information for i2s controllers in Exynos5250
ARM: dts: add Exynos audio subsystem clock controller node
clk: samsung: register audio subsystem clocks using common clock framework
ARM: dts: use #include for all device trees for Samsung
pinctrl: s3c24xx: use correct header for chained_irq functions
...
This patch add pinctrl support to ST SoCs.
About hardware:
ST Set-Top-Box parts have two blocks called PIO and PIO-mux which handle
pin configurations.
Each multi-function pin is controlled, driven and routed through the PIO
multiplexing block. Each pin supports GPIO functionality (ALT0) and
multiple alternate functions(ALT1 - ALTx) that directly connect the pin
to different hardware blocks. When a pin is in GPIO mode, Output Enable
(OE), Open Drain(OD), and Pull Up (PU) are driven by the related PIO
block. Otherwise the PIO multiplexing block configures these parameters
and retiming the signal.
About driver:
This pinctrl driver manages both PIO and PIO-mux block using pinctrl,
pinconf, pinmux, gpio subsystems. All the pinctrl related config
information can only come from device trees.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add a pin control driver for the TZ1090's low power pins via the
powerdown controller SOC_GPIO_CONTROL registers.
These pins have individually controlled pull-up, and group controlled
schmitt, slew-rate, drive-strength, and power-on-start (pos).
The pdc_gpio0 and pdc_gpio1 pins can also be muxed onto the
ir_mod_stable_out and ir_mod_power_out functions respectively. If no
function is set they remain in GPIO mode. These muxes can be overridden
by requesting them as GPIOs.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Rob Landley <rob@landley.net>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-doc@vger.kernel.org
Cc: devicetree-discuss@lists.ozlabs.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add a pin control driver for the main pins on the TZ1090 SoC. This
doesn't include the low-power pins as they're controlled separately via
the Powerdown Controller (PDC) registers.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Rob Landley <rob@landley.net>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-doc@vger.kernel.org
Cc: devicetree-discuss@lists.ozlabs.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Previously if you had MACH_EXYNOS5_DT but not MACH_EXYNOS4_DT you'd be
missing the pincontrol definitions. Move PINCTRL selects to the arch
level since we should be enabling the code for all exynos variants.
Update the PINCTRL descriptions to indicate that PINCTRL_EXYNOS is not
for exynos5440. Also add basic dependencies for the PINCTRL_EXYNOS
kernel config.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add support for gpio on Intel BayTrail platforms. BayTrail supports 3 banks
of gpios called SCORE, NCORE ans SUS with 102, 28 and 44 gpio pins.
Supports gpio interrupts and ACPI gpio events
Pins may be muxed to alternate function instead of gpio by firmware.
This driver does not touch the pin muxing and expect firmare
to set pin muxing and pullup/down properties properly.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This driver adds support the Cortex-A9 based SoCs from Rockchip,
so at least the RK2928, RK3066 (a and b) and RK3188.
Earlier Rockchip SoCs seem to use similar mechanics for gpio
handling so should be supportable with relative small changes.
Pull handling on the rk3188 is currently a stub, due to it being
a bit different to the earlier SoCs.
Pinmuxing as well as gpio (and interrupt-) handling tested on
a rk3066a based machine.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The s3c24xx pins follow a similar pattern as the other Samsung SoCs and
can therefore reuse the already introduced infrastructure.
The s3c24xx SoCs have one design oddity in that the first 4 external
interrupts do not reside in the eint pending register but in the main
interrupt controller instead. We solve this by forwarding the external
interrupt from the main controller into the irq domain of the pin bank.
The masking/acking of these interrupts is handled in the same way.
Furthermore the S3C2412/2413 SoCs contain another oddity in that they
keep the same 4 eints in the main interrupt controller and eintpend
register and requiring ack operations to happen in both. This is solved
by using different compatible properties for the wakeup eint node which
set a property accordingly.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This is a rather large set of patches for device drivers that for one
reason or another the subsystem maintainer preferred to get merged
through the arm-soc tree. There are both new drivers as well as
existing drivers that are getting converted from platform-specific
code into standalone drivers using the appropriate subsystem
specific interfaces.
In particular, we can now have pinctrl, clk, clksource and irqchip
drivers in one file per driver, without the need to call into
platform specific interface, or to get called from platform specific
code, as long as all information about the hardware is provided
through a device tree.
Most of the drivers we touch this time are for clocksource. Since
now most of them are part of drivers/clocksource, I expect that we
won't have to touch these again from arm-soc and can let the
clocksource maintainers take care of these in the future.
Another larger part of this series is specific to the exynos platform,
which is seeing some significant effort in upstreaming and
modernization of its device drivers this time around, which
unfortunately is also the cause for the churn and a lot of the
merge conflicts.
There is one new subsystem that gets merged as part of this series:
the reset controller interface, which is a very simple interface
for taking devices on the SoC out of reset or back into reset.
Patches to use this interface on i.MX follow later in this merge
window, and we are going to have other platforms (at least tegra
and sirf) get converted in 3.11. This will let us get rid of
platform specific callbacks in a number of platform independent
device drivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=ZWk9
-----END PGP SIGNATURE-----
Merge tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver changes from Olof Johansson:
"This is a rather large set of patches for device drivers that for one
reason or another the subsystem maintainer preferred to get merged
through the arm-soc tree. There are both new drivers as well as
existing drivers that are getting converted from platform-specific
code into standalone drivers using the appropriate subsystem specific
interfaces.
In particular, we can now have pinctrl, clk, clksource and irqchip
drivers in one file per driver, without the need to call into platform
specific interface, or to get called from platform specific code, as
long as all information about the hardware is provided through a
device tree.
Most of the drivers we touch this time are for clocksource. Since now
most of them are part of drivers/clocksource, I expect that we won't
have to touch these again from arm-soc and can let the clocksource
maintainers take care of these in the future.
Another larger part of this series is specific to the exynos platform,
which is seeing some significant effort in upstreaming and
modernization of its device drivers this time around, which
unfortunately is also the cause for the churn and a lot of the merge
conflicts.
There is one new subsystem that gets merged as part of this series:
the reset controller interface, which is a very simple interface for
taking devices on the SoC out of reset or back into reset. Patches to
use this interface on i.MX follow later in this merge window, and we
are going to have other platforms (at least tegra and sirf) get
converted in 3.11. This will let us get rid of platform specific
callbacks in a number of platform independent device drivers."
* tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (256 commits)
irqchip: s3c24xx: add missing __init annotations
ARM: dts: Disable the RTC by default on exynos5
clk: exynos5250: Fix parent clock for sclk_mmc{0,1,2,3}
ARM: exynos: restore mach/regs-clock.h for exynos5
clocksource: exynos_mct: fix build error on non-DT
pinctrl: vt8500: wmt: Fix checking return value of pinctrl_register()
irqchip: vt8500: Convert arch-vt8500 to new irqchip infrastructure
reset: NULL deref on allocation failure
reset: Add reset controller API
dt: describe base reset signal binding
ARM: EXYNOS: Add arm-pmu DT binding for exynos421x
ARM: EXYNOS: Add arm-pmu DT binding for exynos5250
ARM: EXYNOS: Enable PMUs for exynos4
irqchip: exynos-combiner: Correct combined IRQs for exynos4
irqchip: exynos-combiner: Add set_irq_affinity function for combiner_irq
ARM: EXYNOS: fix compilation error introduced due to common clock migration
clk: exynos5250: Fix divider values for sclk_mmc{0,1,2,3}
clk: exynos4: export clocks required for fimc-is
clk: samsung: Fix compilation error
clk: tegra: fix enum tegra114_clk to match binding
...
Device-tree updates for 3.10. The bulk of the churn in this branch is due
to i.MX moving from C-defined pin control over to device tree, which is
a one-time conversion that will allow greater flexibility down the road.
Besides that, there's PCI-e bindings for Marvell mvebu platforms and a
handful of cleanups to tegra due to the new include file functionality
of the device tree compiler.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=8X1b
-----END PGP SIGNATURE-----
Merge tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC device-tree updates from Olof Johansson:
"Part 1 of device-tree updates for 3.10. The bulk of the churn in this
branch is due to i.MX moving from C-defined pin control over to device
tree, which is a one-time conversion that will allow greater
flexibility down the road.
Besides that, there's PCI-e bindings for Marvell mvebu platforms and a
handful of cleanups to tegra due to the new include file functionality
of the device tree compiler"
* tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (113 commits)
arm: mvebu: PCIe Device Tree informations for Armada XP GP
arm: mvebu: PCIe Device Tree informations for Armada 370 DB
arm: mvebu: PCIe Device Tree informations for Armada 370 Mirabox
arm: mvebu: PCIe Device Tree informations for Armada XP DB
arm: mvebu: PCIe Device Tree informations for OpenBlocks AX3-4
arm: mvebu: add PCIe Device Tree informations for Armada XP
arm: mvebu: add PCIe Device Tree informations for Armada 370
ARM: sunxi: unify osc24M_fixed and osc24M
arm: vt8500: Add SDHC support to WM8505 DT
ARM: dts: Add a 64 bits version of the skeleton device tree
ARM: mvebu: Add Device Bus and CFI flash memory support to defconfig
ARM: mvebu: Add support for NOR flash device on Openblocks AX3 board
ARM: mvebu: Add support for NOR flash device on Armada XP-GP board
ARM: mvebu: Add Device Bus support for Armada 370/XP SoC
ARM: dts: imx6dl-wandboard: Add USB Host support
ARM: dts: imx51 cpu node
ARM: dts: Add missing imx27-phytec-phycore dtb target
ARM: dts: Add NFC support for i.MX27 Phytec PCM038 module
ARM: i.MX51: Add PATA support
ARM: dts: Add initial support for Wandboard Dual-Lite
...
Add a pinctrl driver for i.MX6 SoloLite based on pinctrl-imx core
driver.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
The imx6dl is a derivative of imx6q with very limited difference. These
two SoCs are so compatible that they can be handled as one platform in
software. That said, we will not have target SOC_IMX6DL but just
reusing SOC_IMX6Q. That's why the pinctrl-imx6dl driver is added here
with symbol PINCTRL_IMX6Q controlling the build of it.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds pinctrl-s3c64xx driver which implements pin control
interface for Samsung S3C64xx SoCs.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds support for the GPIO/pinmux controller found on the VIA
VT8500 and Wondermedia WM8xxx-series SoCs.
Each pin within the controller is capable of operating as a GPIO or as
an alternate function. The pins are numbered according to their control
bank/bit so that if new pins are added, the existing numbering is maintained.
All currently supported SoCs are included: VT8500, WM8505, WM8650, WM8750 and
WM8850.
Signed-off-by: Tony Prisk <linux@prisktech.co.nz>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
pinctrl-pxa driver doesn't support well on DT mode. Now pinctrl-single
could support DT mode & pin configuration. Use pinctrl-single driver to
support MMP/PXA silicons instead.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Support the operation of generic pinconf. The supported config arguments
are INPUT_SCHMITT, INPUT_SCHMITT_ENABLE, DRIVE_STRENGHT, BIAS_DISABLE,
BIAS_PULLUP, BIAS_PULLDOWN, SLEW_RATE.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This is another cleanup series, containing the move of the Renesas
SH-Mobile pin controller code from arch/arm/mach-shmobile over to the
generic pinctrl subsystem, changing it over to the common interfaces in
the process.
Based on agreement between Olof, Paul Mundt, Linus Walleij and Simon,
we're merging this large branch of pinctrl conversion through arm-soc,
even though it contains the corresponding conversions for arch/sh. Main
reason for this is tight dependencies (that will now mostly be broken)
between the arch/sh and mach-shmobile implementations.
There will be more of this in 3.10 to do device-tree bindings, but this
is the initial conversion.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=U+ce
-----END PGP SIGNATURE-----
Merge tag 'sh-pinmux' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull sh-mobile pinctrl conversion from Arnd Bergmann:
"This is another cleanup series, containing the move of the Renesas
SH-Mobile pin controller code from arch/arm/mach-shmobile over to the
generic pinctrl subsystem, changing it over to the common interfaces
in the process.
Based on agreement between Olof, Paul Mundt, Linus Walleij and Simon,
we're merging this large branch of pinctrl conversion through arm-soc,
even though it contains the corresponding conversions for arch/sh.
Main reason for this is tight dependencies (that will now mostly be
broken) between the arch/sh and mach-shmobile implementations.
There will be more of this in 3.10 to do device-tree bindings, but
this is the initial conversion."
* tag 'sh-pinmux' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (81 commits)
sh-pfc: sh_pfc_probe() sizeof() fix
sh-pfc: Move sh_pfc.h from include/linux/ to driver directory
sh-pfc: Remove pinmux_info definition
sh: Remove unused sh_pfc_register_info() function
sh: shx3: pinmux: Use driver-provided pinmux info
sh: sh7786: pinmux: Use driver-provided pinmux info
sh: sh7785: pinmux: Use driver-provided pinmux info
sh: sh7757: pinmux: Use driver-provided pinmux info
sh: sh7734: pinmux: Use driver-provided pinmux info
sh: sh7724: pinmux: Use driver-provided pinmux info
sh: sh7723: pinmux: Use driver-provided pinmux info
sh: sh7722: pinmux: Use driver-provided pinmux info
sh: sh7720: pinmux: Use driver-provided pinmux info
sh: sh7269: pinmux: Use driver-provided pinmux info
sh: sh7264: pinmux: Use driver-provided pinmux info
sh: sh7203: pinmux: Use driver-provided pinmux info
ARM: shmobile: sh73a0: Use driver-provided pinmux info
ARM: shmobile: sh7372: Use driver-provided pinmux info
ARM: shmobile: r8a7779: Use driver-provided pinmux info
ARM: shmobile: r8a7740: Use driver-provided pinmux info
...
- Grabbing of default pinctrl handles from the device core.
These are the hunks hitting drivers/base. All is ACKed by
Greg, after a long discussion about different alternatives.
- Some stuff also touches the MFD and ARM SoC trees, this has
been coordinated and ACKed.
- New drivers for:
- The Tegra 114 sub-SoC
- Allwinner sunxi
- New ABx500 driver and sub-SoC drivers for AB8500,
AB8505, AB9540 and AB8540.
- Make it possible for hogged pins to enter a sleep mode,
and make it possible for drivers to control that mode.
- Various clean-up, extensions and device tree support to
various pin controllers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=SQ9W
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-for-v3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pinctrl changes from Linus Walleij:
"These are the main pinctrl changes for the v3.9 merge window. The
most interesting change by far is how the device core grabs pinctrl
default handles avoiding the need to stick boilerplate into driver
consumers.
- Grabbing of default pinctrl handles from the device core. These
are the hunks hitting drivers/base. All is ACKed by Greg, after a
long discussion about different alternatives.
- Some stuff also touches the MFD and ARM SoC trees, this has been
coordinated and ACKed.
- New drivers for:
- The Tegra 114 sub-SoC
- Allwinner sunxi
- New ABx500 driver and sub-SoC drivers for AB8500, AB8505, AB9540
and AB8540.
- Make it possible for hogged pins to enter a sleep mode, and make it
possible for drivers to control that mode.
- Various clean-up, extensions and device tree support to various pin
controllers."
* tag 'pinctrl-for-v3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (68 commits)
pinctrl: tegra: add clfvs function to Tegra114 support
pinctrl: generic: rename input schmitt disable
pinctrl/pinconfig: add debug interface
pinctrl: samsung: remove duplicated line
ARM: ux500: use real AB8500 IRQ numbers instead of virtual ones
ARM: ux500: remove irq_base property from platform_data
pinctrl/abx500: use direct IRQ defines
pinctrl/abx500: replace IRQ offsets with table read-in values
pinctrl/abx500: move IRQ handling to ab8500-core
pinctrl: exynos5440: remove erroneous __init
pinctrl/abx500: adjust offset for get_mode()
pinctrl/abx500: add Device Tree support
pinctrl/abx500: align GPIO cluster boundaries
pinctrl/abx500: prevent error path from corrupting returning error
pinctrl: sunxi: add of_xlate function
pinctrl/lantiq: fix pin number in ltq_pmx_gpio_request_enable
pinctrl/lantiq: add functionality to falcon_pinconf_dbg_show
pinctrl/lantiq: fix pinconfig parameters
pinctrl/lantiq: one of the boot leds was defined incorrectly
pinctrl/lantiq: only probe available pad controllers
...
Since pinctrl-exynos can support exynos4 and exynos5 so changed
the option name to PINCTRL_EXYNOS for more clarity.
Cc: Thomas Abraham <Thomas.abraham@linaro.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add AB8540 sub driver to the ABx500 family, pins, pin groups and
gpio range.
As the pin controller (also the ABx500 controllers) is an
inherent part of the SoC and will prevent boot if not
available, select this from the Ux500 SoC Kconfig.
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Patrice Chotard <patrice.chotard@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add AB9540 sub driver to the ABx500 family, pins, pin groups and
gpio range.
As the pin controller (also the ABx500 controllers) is an
inherent part of the SoC and will prevent boot if not
available, select this from the Ux500 SoC Kconfig.
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Patrice Chotard <patrice.chotard@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add AB8505 sub driver to the ABx5x family.
As the pin controller (also the ABx500 controllers) is an
inherent part of the SoC and will prevent boot if not
available, select this from the Ux500 SoC Kconfig.
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Patrice Chotard <patrice.chotard@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds a subdriver for the AB8500 pinctrl portions.
As the pin controller (also the ABx500 controllers) is an
inherent part of the SoC and will prevent boot if not
available, select this from the Ux500 SoC Kconfig.
Acked-by: Olof Johansson <olof@lixom.net>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds the AB8500 core driver, which will be utilized by
the follow-on drivers for different ABx500 variants.
Sselect the driver from the DBX500_SOC, as this chip is
powering and clocking that SoC.
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Allwinner SoCs have an IP module that handle both the muxing and the
GPIOs.
This IP has 8 banks of 32 bits, with a number of pins actually useful
for each of these banks varying from one to another, and depending on
the SoC used on the board.
This driver only implements the pinctrl part, the gpio part will come
eventually.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since pinctrl-exynos can support exynos4 and exynos5 so changed
the option name to PINCTRL_EXYNOS for more clarity.
Cc: Thomas Abraham <Thomas.abraham@linaro.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds a driver for the Tegra114 pinmux, and required
parameterization data for Tegra114.
The driver uses the common Tegra pincontrol driver utility
functions to implement the majority of the driver.
This driver is not compatible with the earlier NVIDIA's SoCs,
hence add new compatibile as "nvidia,tegra114-pinmux".
Originally written by Pritesh.
ldewangan:
- cleanup the patches,
- remove non-require tables.
- Use module_platform_driver() for driver registartion.
Signed-off-by: Pritesh Raithatha <praithatha@nvidia.com>
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Now, PINCTRL_SAMSUNG should be enabled with PINCTRL_EXYNOS so we don't
need to add 'depends on' condition already added in PINCTRL_EXYNOS.
Cc: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This contains the bulk of new SoC development for this merge window.
Two new platforms have been added, the sunxi platforms (Allwinner A1x
SoCs) by Maxime Ripard, and a generic Broadcom platform for a new
series of ARMv7 platforms from them, where the hope is that we can
keep the platform code generic enough to have them all share one mach
directory. The new Broadcom platform is contributed by Christian Daudt.
Highbank has grown support for Calxeda's next generation of hardware,
ECX-2000.
clps711x has seen a lot of cleanup from Alexander Shiyan, and he's also
taken on maintainership of the platform.
Beyond this there has been a bunch of work from a number of people on
converting more platforms to IRQ domains, pinctrl conversion, cleanup
and general feature enablement across most of the active platforms.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=YMKB
-----END PGP SIGNATURE-----
Merge tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC updates from Olof Johansson:
"This contains the bulk of new SoC development for this merge window.
Two new platforms have been added, the sunxi platforms (Allwinner A1x
SoCs) by Maxime Ripard, and a generic Broadcom platform for a new
series of ARMv7 platforms from them, where the hope is that we can
keep the platform code generic enough to have them all share one mach
directory. The new Broadcom platform is contributed by Christian
Daudt.
Highbank has grown support for Calxeda's next generation of hardware,
ECX-2000.
clps711x has seen a lot of cleanup from Alexander Shiyan, and he's
also taken on maintainership of the platform.
Beyond this there has been a bunch of work from a number of people on
converting more platforms to IRQ domains, pinctrl conversion, cleanup
and general feature enablement across most of the active platforms."
Fix up trivial conflicts as per Olof.
* tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (174 commits)
mfd: vexpress-sysreg: Remove LEDs code
irqchip: irq-sunxi: Add terminating entry for sunxi_irq_dt_ids
clocksource: sunxi_timer: Add terminating entry for sunxi_timer_dt_ids
irq: versatile: delete dangling variable
ARM: sunxi: add missing include for mdelay()
ARM: EXYNOS: Avoid early use of of_machine_is_compatible()
ARM: dts: add node for PL330 MDMA1 controller for exynos4
ARM: EXYNOS: Add support for secondary CPU bring-up on Exynos4412
ARM: EXYNOS: add UART3 to DEBUG_LL ports
ARM: S3C24XX: Add clkdev entry for camif-upll clock
ARM: SAMSUNG: Add s3c24xx/s3c64xx CAMIF GPIO setup helpers
ARM: sunxi: Add missing sun4i.dtsi file
pinctrl: samsung: Do not initialise statics to 0
ARM i.MX6: remove gate_mask from pllv3
ARM i.MX6: Fix ethernet PLL clocks
ARM i.MX6: rename PLLs according to datasheet
ARM i.MX6: Add pwm support
ARM i.MX51: Add pwm support
ARM i.MX53: Add pwm support
ARM: mx5: Replace clk_register_clkdev with clock DT lookup
...
As can be seen from the diffstat the major changes
are:
- A big conversion of the AT91 pinctrl driver and
the associated ACKed platform changes under
arch/arm/max-at91 and its device trees. This
has been coordinated with the AT91 maintainers
to go in through the pinctrl tree.
- A larger chunk of changes to the SPEAr drivers
and the addition of the "plgpio" driver for the
SPEAr as well.
- The removal of the remnants of the Nomadik driver
from the arch/arm tree and fusion of that into
the Nomadik driver and platform data header files.
- Some local movement in the Marvell MVEBU drivers,
these now have their own subdirectory.
- The addition of a chunk of code to gpiolib under
drivers/gpio to register gpio-to-pin range mappings
from the GPIO side of things. This has been
requested by Grant Likely and is now implemented,
it is particularly useful for device tree work.
Then we have incremental updates all over the place,
many of these are cleanups and fixes from Axel Lin
who has done a great job of removing minor mistakes
and compilation annoyances.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)
iQIcBAABAgAGBQJQupLkAAoJEEEQszewGV1z8ykP/3yLi5hb3QstajrL3jvrHcqN
7sc4uW1/9pCa6802nBw7qOfIGxgTAriGtAIePdtGhIkij6TLyyWfvlmUz3iJkeZ5
4nYy69yOdNMeBGvhXBkBD4K4lL3NGZ9eR+S1rgWY0J3Y+a5upibJeaXxmYBayjBH
bN/OiK77zaKv91zKSZ4YW9WCzrjn2E0w1mDRcWdffcyrNplY8qm/G2iXBT+UoCLa
UoR1zxG9nqF+nQ8mL+dVtVjlHsUcj0NEp34HQrUQ8ACOaEIiSI/zDe7afOC38Iy7
EUTV4IwKeKJyTnAN/QSzbTXF41CR/Qbihubo6sUrbAmyJXLnybVotd4Inh4ca7II
c2TPV89tSnJWwDSizHwbY3sXIVw8ojmjYMr1ib0Z9GBGyoij1va5WqCJ4iIzTzuc
imvDSz8ctuuxo6iOQs3smUaHXGz1V+3zvQ5v+Ioc1h9mN2LVKNa6NjmFNZmeFHLa
44zIes51DUXizaRobOffjoTIlUkAdwYQUpRtq0hvQtgYTyUIeXzfzCNzDoT6bhK3
VhLn4c4apETER6KtYCPu8PtxM/yyopwUj95WvnPK2fu/m+1B26jUVawomWfRtCQF
kuovLCTTemn04jWWl3r0JovE/tVcgBrpxTYi6Z4RPY7PuD4sQ477DeM2x3DWZPQQ
MHveLGA87735XKZkqQRR
=rUOP
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-for-v3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pinctrl changes from Linus Walleij:
"These are the first and major pinctrl changes for the v3.8 merge
cycle. Some of this is used as merge base for other trees so I better
be early on the trigger.
As can be seen from the diffstat the major changes are:
- A big conversion of the AT91 pinctrl driver and the associated ACKed
platform changes under arch/arm/max-at91 and its device trees. This
has been coordinated with the AT91 maintainers to go in through the
pinctrl tree.
- A larger chunk of changes to the SPEAr drivers and the addition of
the "plgpio" driver for the SPEAr as well.
- The removal of the remnants of the Nomadik driver from the arch/arm
tree and fusion of that into the Nomadik driver and platform data
header files.
- Some local movement in the Marvell MVEBU drivers, these now have
their own subdirectory.
- The addition of a chunk of code to gpiolib under drivers/gpio to
register gpio-to-pin range mappings from the GPIO side of things.
This has been requested by Grant Likely and is now implemented, it
is particularly useful for device tree work.
Then we have incremental updates all over the place, many of these are
cleanups and fixes from Axel Lin who has done a great job of removing
minor mistakes and compilation annoyances."
* tag 'pinctrl-for-v3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (114 commits)
ARM: mmp: select PINCTRL for ARCH_MMP
pinctrl: Drop selecting PINCONF for MMP2, PXA168 and PXA910
pinctrl: pinctrl-single: Fix error check condition
pinctrl: SPEAr: Update error check for unsigned variables
gpiolib: Fix use after free in gpiochip_add_pin_range
gpiolib: rename pin range arguments
pinctrl: single: support gpio request and free
pinctrl: generic: add input schmitt disable parameter
pinctrl/u300/coh901: stop spawning pinctrl from GPIO
pinctrl/u300/coh901: let the gpio_chip register the range
pinctrl: add function to retrieve range from pin
gpiolib: return any error code from range creation
pinctrl: make range registration defer properly
gpiolib: rename find_pinctrl_*
gpiolib: let gpiochip_add_pin_range() specify offset
ARM: at91: pm9g45: add mmc support
ARM: at91: Animeo IP: add mmc support
ARM: at91: dt: add mmc pinctrl for Atmel reference boards
ARM: at91: dt: at91sam9: add mmc pinctrl support
ARM: at91/dts: add nodes for atmel hsmci controllers for atmel boards
...
Add a new pinctrl driver for Samsung EXYNOS5440 SoC. The pin controller
module in EXYNOS5440 is different from the pin controller found on other
Samsung SoC. Hence, the pin controller driver for EXYNOS5440 SoC is
independent of the Samsung pinctrl framework.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The main samsung pinctrl module references the specific exynos4210
pinctrl driver, which selects the main driver in Kconfig.
Making the main driver a silent "bool" option avoid this potential
build error if CONFIG_PINCTRL_SAMSUNG=y && CONFIG_PINCTRL_EXYNOS4=n:
drivers/built-in.o:(.rodata+0x4e4): undefined reference to `exynos4210_pin_ctrl'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Tomasz Figa <t.figa@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Then we can remove "select PINMUX && PINCONF" from PINCTRL_TEGRA{20,30}.
This simplifies the dependency.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Then we can remove "select PINMUX && PINCONF" from PINCTRL_IMX{23,28}.
This simplifies the dependency.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The driver supports old up SiRFprimaII SoCs, this patch makes it support
the new SiRFmarco as well.
SiRFmarco, as a SMP SoC, adds new SIRFSOC_GPIO_PAD_EN_CLR registers, to
disable GPIO pad, we should write 1 to the corresponding bit in the new
CLEAR register instead of writing 0 to SIRFSOC_GPIO_PAD_EN.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Like the spear platform, the mvebu platform has multiple files: one
core file, and then one file per SoC family. More files will be added
later, as support for mach-orion5x and mach-mv78xx0 SoCs is added to
pinctrl-mvebu. For those reasons, having a separate subdirectory,
drivers/pinctrl/mvebu/ makes sense, and it had already been suggested
by Linus Wallej when the driver was originally submitted.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The mach-kirkwood and mach-dove architectures have not yet been
integrated into the mach-mvebu directory, which should ultimately
contain the support for all Marvell SoCs from the Engineering Business
Unit.
However, before this can happen, we need to let mach-kirkwood and
mach-dove use the pinctrl-mvebu driver, which supports the kirkwood
and dove SoC families. In order to do that, we make this driver
available as soon as PLAT_ORION is selected, instead of using
ARCH_MVEBU as a condition. In the long term, PLAT_ORION should
disappear and be fully replaced by ARCH_MVEBU, but the plan is to make
the migration step by step, by first having the existing mach-*
directories for Marvell SoCs converge on several infrastructures,
including the pinctrl one.
Also, like the spear pinctrl driver, we put all pinctrl-mvebu Kconfig
options under a if, in order to avoid having certain options
(PINCTRL_DOVE, PINCTRL_KIRKWOOD, etc.) selecting an option
(PINCTLR_MVEBU) which itself has a dependency (on ARCH_MVEBU). In this
a construct, the dependency is in fact ignored due to the selects.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch fixes below build error when !CONFIG_OF_GPIO.
CC drivers/pinctrl/pinctrl-samsung.o
drivers/pinctrl/pinctrl-samsung.c: In function 'samsung_pinctrl_parse_dt_pins':
drivers/pinctrl/pinctrl-samsung.c:557:19: warning: unused variable 'prop' [-Wunused-variable]
drivers/pinctrl/pinctrl-samsung.c: In function 'samsung_gpiolib_register':
drivers/pinctrl/pinctrl-samsung.c:797:5: error: 'struct gpio_chip' has no member named 'of_node'
make[2]: *** [drivers/pinctrl/pinctrl-samsung.o] Error 1
make[1]: *** [drivers/pinctrl] Error 2
make: *** [drivers] Error 2
The samsung pinctrl driver supports only device tree enabled
platforms. Thus make PINCTRL_SAMSUNG depend on OF && GPIOLIB.
The reason to depend on GPIOLIB is CONFIG_OF_GPIO only available
when GPIOLIB is selected.
Since PINCTRL_EXYNOS4 select PINCTRL_SAMSUNG, thus also make
PINCTRL_EXYNOS4 depend on OF && GPIOLIB.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This is also include the gpio controller as the IP share both.
Each soc will have to describe the SoC limitation and pin configuration via
DT.
This will allow to do not need to touch the C code when adding new SoC if the
IP version is supported.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Pull MIPS update from Ralf Baechle:
"This is the MIPS update for 3.7.
A fair chunk of them are platform updates to the Cavium Octeon SOC
(which involves machine generated header files of considerable size),
Atheros ATH79xx, RMI aka Netlogic aka Broadcom XLP, Broadcom BCM63xx
platforms.
Support for the commercial MIPS simulator MIPSsim has been removed as
MIPS Technologies is shifting away from this product and Qemu is
offering various more powerful platforms. The generic MIPS code can
now also probe for no-execute / write-only TLB features implemented
without the full SmartMIPS extension as permitted by the latest MIPS
processor architecture. Lots of small changes to generic code."
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (78 commits)
MIPS: ath79: Fix CPU/DDR frequency calculation for SRIF PLLs
MIPS: ath79: use correct fractional dividers for {CPU,DDR}_PLL on AR934x
MIPS: BCM63XX: Properly handle mac address octet overflow
MIPS: Kconfig: Avoid build errors by hiding USE_OF from the user.
MIPS: Replace `-' in defconfig filename wth `_' for consistency.
MIPS: Wire kcmp syscall.
MIPS: MIPSsim: Remove the MIPSsim platform.
MIPS: NOTIFY_RESUME is not needed in TIF masks
MIPS: Merge the identical "return from syscall" per-ABI code
MIPS: Unobfuscate _TIF..._MASK
MIPS: Prevent hitting do_notify_resume() with !user_mode(regs).
MIPS: Replace 'kernel_uses_smartmips_rixi' with 'cpu_has_rixi'.
MIPS: Add base architecture support for RI and XI.
MIPS: Optimise TLB handlers for MIPS32/64 R2 cores.
MIPS: uasm: Add INS and EXT instructions.
MIPS: Avoid pipeline stalls on some MIPS32R2 cores.
MIPS: Make VPE count to be one-based.
MIPS: Add new end of interrupt functionality for GIC.
MIPS: Add EIC support for GIC.
MIPS: Code clean-ups for the GIC.
...
This branch contains updates to OMAP and Marvell platforms (kirkwood,
dove, mvebu) that came in after we had done the big multiplatform merges,
so they were kept separate from the rest, and not separated into the
traditional topics of cleanup/driver/platform features.
For OMAP, the updates are:
- Runtime PM conversions for the GPMC and RNG IP blocks
- Preparation patches for the OMAP common clock framework conversion
- clkdev alias additions required by other drivers
- Performance Monitoring Unit (PMU) support for OMAP2, 3, and non-4430 OMAP4
- OMAP hwmod code and data improvements
- Preparation patches for the IOMMU runtime PM conversion
- Preparation patches for OMAP4 full-chip retention support
For Kirkwood/Dove/mvebu:
- New driver for "address decoder controller" for mvebu, which
is a piece of hardware that configures addressable devices and
peripherals. First user is the boot rom aperture on armada XP since
it is needed for SMP support.
- New device tree bindings for peripherals such as gpio-fan, iconnect
nand, mv_cesa and the above address decoder controller.
- Some defconfig updates, mostly to enable new DT boards and a few drivers.
- New drivers using the pincontrol subsystem for dove, kirkwood and mvebu
- New clean gpio driver for mvebu
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=xVaJ
-----END PGP SIGNATURE-----
Merge tag 'soc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull late ARM soc platform updates from Olof Johansson:
"This branch contains updates to OMAP and Marvell platforms (kirkwood,
dove, mvebu) that came in after we had done the big multiplatform
merges, so they were kept separate from the rest, and not separated
into the traditional topics of cleanup/driver/platform features.
For OMAP, the updates are:
- Runtime PM conversions for the GPMC and RNG IP blocks
- Preparation patches for the OMAP common clock framework conversion
- clkdev alias additions required by other drivers
- Performance Monitoring Unit (PMU) support for OMAP2, 3, and
non-4430 OMAP4
- OMAP hwmod code and data improvements
- Preparation patches for the IOMMU runtime PM conversion
- Preparation patches for OMAP4 full-chip retention support
For Kirkwood/Dove/mvebu:
- New driver for "address decoder controller" for mvebu, which is a
piece of hardware that configures addressable devices and
peripherals. First user is the boot rom aperture on armada XP
since it is needed for SMP support.
- New device tree bindings for peripherals such as gpio-fan, iconnect
nand, mv_cesa and the above address decoder controller.
- Some defconfig updates, mostly to enable new DT boards and a few
drivers.
- New drivers using the pincontrol subsystem for dove, kirkwood and
mvebu
- New clean gpio driver for mvebu"
* tag 'soc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (98 commits)
ARM: mvebu: fix build breaks from multi-platform conversion
ARM: OMAP4460/4470: PMU: Enable PMU for OMAP4460/70
ARM: OMAP2+: PMU: Add runtime PM support
ARM: OMAP4430: PMU: prepare to create PMU device via HWMOD
ARM: OMAP2+: PMU: Convert OMAP2/3 devices to use HWMOD
ARM: OMAP3: hwmod data: Add debugss HWMOD data
ARM: OMAP2+: clockdomain/hwmod: add workaround for EMU clockdomain idle problems
ARM: OMAP: Add a timer attribute for timers that can interrupt the DSP
hwrng: OMAP: remove SoC restrictions from driver registration
ARM: OMAP: split OMAP1, OMAP2+ RNG device registration
hwrng: OMAP: convert to use runtime PM
hwrng: OMAP: store per-device data in per-device variables, not file statics
ARM: OMAP2xxx: hwmod/CM: add RNG integration data
ARM: OMAP2+: gpmc: minimal driver support
ARM: OMAP2+: gpmc: Adapt to HWMOD
ARM: OMAP2/3: hwmod data: add gpmc
ARM: OMAP4: hwmod data: add mmu hwmod for ipu and dsp
ARM: OMAP3: hwmod data: add mmu data for iva and isp
ARM: OMAP: iommu: fix including iommu.h without IOMMU_API selected
ARM: OMAP4: hwmod data: add missing HWMOD_NO_IDLEST flags to some PRCM IP blocks
...
- Add subdrivers for the DB8540 and NHK8815 Nomadik-type ASICs,
provide platform config for the Nomadik.
- Add a driver for the i.MX35.
- Add a driver for the BCM2835, an advanced GPIO expander.
- Various fixes and clean-ups and minor improvements for the core,
Nomadik, pinctr-single, sirf drivers.
- Some platform config for the ux500.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=g2i2
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-for-v3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pinctrl changes from Linus Walleij:
"Some of this stuff is hitting arch/arm/* and have been ACKed by the
ARM SoC folks, or it's device tree bindings pertaining to the specific
driver.
These are the bulk pinctrl changes for kernel v3.7:
- Add subdrivers for the DB8540 and NHK8815 Nomadik-type ASICs,
provide platform config for the Nomadik.
- Add a driver for the i.MX35.
- Add a driver for the BCM2835, an advanced GPIO expander.
- Various fixes and clean-ups and minor improvements for the core,
Nomadik, pinctr-single, sirf drivers.
- Some platform config for the ux500."
* tag 'pinctrl-for-v3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (27 commits)
pinctrl: add bcm2835 driver
pinctrl: clarify idle vs sleep states
pinctrl/nomadik: use irq_find_mapping()
pinctrl: sirf: add lost chained_irq_enter and exit in sirfsoc_gpio_handle_irq
pinctrl: sirf: initialize the irq_chip pointer of pinctrl_gpio_range
pinctrl: sirf: fix spinlock deadlock in sirfsoc_gpio_set_input
pinctrl: sirf: add missing pins to pinctrl list
pinctrl: sirf: fix a typo in sirfsoc_gpio_probe
pinctrl: pinctrl-single: add debugfs pin h/w state info
ARM: ux500: 8500: update I2C sleep states pinctrl
pinctrl: Fix potential memory leak in pinctrl_register_one_pin()
ARM: ux500: tidy up pin sleep modes
ARM: ux500: fix spi2 pin group
pinctrl: imx: remove duplicated const
pinctrl: document semantics vs GPIO
ARM: ux500: 8500: use hsit_a_2 group for HSI
pinctrl: use kasprintf() in pinmux_request_gpio()
pinctrl: pinctrl-single: Add pinctrl-single,bits type of mux
pinctrl/nomadik : add MC1_a_2 pin MC1 function group list
pinctrl: pinctrl-single: Make sure we do not change bits outside of mask
...
The BCM2835 GPIO module is a combined GPIO controller, (GPIO) interrupt
controller, and pinmux/control device.
Original driver by Simon Arlott.
Rewrite including GPIO chip device by Chris Boot.
Upstreaming changes by Stephen Warren:
* Wrote DT binding documentation.
* Changed brcm,function to an integer to more directly match the
datasheet, and to match brcm,pins being an integer.
* Implemented pull-up/down pin config.
* Removed read-only DT property and related code. The restriction this
implemented are driven by the board, not the GPIO HW block, so don't
really make sense of a HW block binding, were in general incomplete
(since they could only know about the few pins hard-coded into the
Raspberry Pi B board design and not the uncommitted GPIOS), and are
better represented simply by not writing incorrect data into pin
configuration nodes.
* Don't set GPIO_IN function select in gpio_request_enable() to avoid
glitches; defer this to gpio_set_direction(). Consequently, removed
empty bcm2835_pmx_gpio_request_enable().
* Simplified enabled_irq_map[]; make it explicitly 1 entry per bank.
* Lifted use of enabled_irq_map[] outside the per-interrupt loop in
IRQ handler, thus fixing an issue where the code was indexing into
enabled_irq_map[] by intra-bank GPIO ID, not global GPIO ID.
* Removed locking in IRQ handler, since all other code uses
spin_lock_irqsave() and so guarantees it doesn't run concurrently
with the handler.
* Moved duplicated BUILD_BUG_ON()s into probe(). Also check size of
bcm2835_gpio_pins[].
* Remove range-checking from bcm2835_pctl_get_groups_count() since we've
decided to trust the pinctrl core.
* Made bcm2835_pmx_gpio_disable_free() call bcm2835_pinctrl_fsel_set()
directly for simplicity.
* Fixed body of dt_free_map() to match latest dt_node_to_map().
* Removed GPIO ownership check from bcm2835_pmx_enable() since the pinctrl
core owns doing this.
* Made irq_chip and pinctrl_gpio_range .name == MODULE_NAME so it's more
descriptive.
* Simplified remove(); removed call to non-existent
pinctrl_remove_gpio_range(), remove early return on error.
* Don't force gpiochip's base to 0. Set gpio_range.base to gpiochip's
base GPIO number.
* Error-handling cleanups in probe().
* Switched to module_platform_driver() rather than open-coding.
* Made pin, group, and function names lower-case.
* s/broadcom/brcm/ in DT property names.
* s/2708/2835/.
* Fixed a couple minor checkpatch warnings, and other minor cleanup.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Chris Boot <bootc@bootc.net>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This pinctrl driver is not a full-blown pinctrl driver from scratch:
it relies on the common pinctrl-mvebu driver, which is used for all
Marvell EBU SoCs.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This pinctrl driver is not a full-blown pinctrl driver from scratch:
it relies on the common pinctrl-mvebu driver, which is used for all
Marvell EBU SoCs.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This patch adds a SoC specific pinctrl driver for Marvell Kirkwood SoCs
plus DT binding documentation. This driver will use the mvebu pinctrl
driver core.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Stephen Warren <swarren@wwwdotorg.org>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This patch adds a SoC specific pinctrl driver for Marvell Dove SoCs
plus DT binding documentation. This driver will use the mvebu pinctrl
driver core.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This patch adds a pinctrl driver core for Marvell SoCs plus DT
binding documentation. This core driver will be used by SoC family
specific drivers, i.e. Armada XP, Armada 370, Dove, Kirkwood, aso.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Conflicts:
arch/arm/Kconfig
Implement support for pinctrl on lantiq/falcon socs. The FALCON has 5 banks
of up to 32 pins.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Thomas Langer <thomas.langer@lantiq.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: devicetree-discuss@lists.ozlabs.org
Cc: linux-kernel@vger.kernel.org
Implement support for pinctrl on lantiq/xway socs. The IO core found on these
socs has the registers for pinctrl, pinconf and gpio mixed up in the same
register range. As the gpio_chip handling is only a few lines, the driver also
implements the gpio functionality. This obseletes the old gpio driver that was
located in the arch/ folder.
Signed-off-by: John Crispin <blogic@openwrt.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: devicetree-discuss@lists.ozlabs.org
Cc: linux-kernel@vger.kernel.org
Add information about the Exynos4210 pin banks and driver data which is
used by the Samsung pinctrl driver. In addition to this, the support for
external gpio and wakeup interrupt support is included and hooked up with
the Samsung pinctrl driver.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add a new device tree enabled pinctrl and gpiolib driver for Samsung
SoC's. This driver provides a common and extensible framework for all
Samsung SoC's to interface with the pinctrl and gpiolib subsystems. This
driver supports only device tree based instantiation and hence can be
used only on those Samsung platforms that have device tree enabled.
This driver is split into two parts: the pinctrl interface and the gpiolib
interface. The pinctrl interface registers pinctrl devices with the pinctrl
subsystem and gpiolib interface registers gpio chips with the gpiolib
subsystem. The information about the pins, pin groups, pin functions and
gpio chips, which are SoC specific, are parsed from device tree node.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This is mostly cut'n'paste from the imx51 pinctrl driver.
The data was generated using sed and awk on
arch/arm/plat-mxc/include/mach/iomux-mx35.h.
Changes since (implicit) v1
- remove references to file names in binding documentation
- remove sed commands from comments in driver
- add explicit numbers for pins and functions
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds support for the STN8815 ASIC for the Nomadik pin
controller.
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This implements a subdriver for the DB8540 ASIC for the
Nomadik pin controller.
Signed-off-by: Patrice Chotard <patrice.chotard@stericsson.com>
Reviewed-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add one-register-per-pin type device tree based pinctrl driver.
This driver has been tested on omap2+ series of processors,
where there is either an 8 or 16-bit padconf register for each pin.
Support for other similar pinmux controllers can be added.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Kconfig entry for the COH901 pin controller depended on
PINMUX_U300 which is stale, use PINCTRL_U300 as it is called
these days.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
With this, five platforms are moving to the relatively new pinctrl
subsystem for their pin management, replacing the older soc specific
in-kernel interfaces with common code.
There is quite a bit of net addition of code for each platform being
added to the pinctrl subsystem. but the payback comes later when adding
new boards can be done by only providing new device trees instead.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=HIfz
-----END PGP SIGNATURE-----
Merge tag 'pinctrl' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm soc-specific pinctrl changes from Olof Johansson:
"With this, five platforms are moving to the relatively new pinctrl
subsystem for their pin management, replacing the older soc specific
in-kernel interfaces with common code.
There is quite a bit of net addition of code for each platform being
added to the pinctrl subsystem. But the payback comes later when
adding new boards can be done by only providing new device trees
instead."
Fix up trivial conflicts in arch/arm/mach-ux500/{Makefile,board-mop500.c}
* tag 'pinctrl' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (61 commits)
mtd: nand: gpmi: fix compile error caused by pinctrl call
ARM: PRIMA2: select PINCTRL and PINCTRL_SIRF in Kconfig
ARM: nomadik: enable PINCTRL_NOMADIK where needed
ARM: mxs: enable pinctrl support
video: mxsfb: adopt pinctrl support
ASoC: mxs-saif: adopt pinctrl support
i2c: mxs: adopt pinctrl support
mtd: nand: gpmi: adopt pinctrl support
mmc: mxs-mmc: adopt pinctrl support
serial: mxs-auart: adopt pinctrl support
serial: amba-pl011: adopt pinctrl support
spi/imx: adopt pinctrl support
i2c: imx: adopt pinctrl support
can: flexcan: adopt pinctrl support
net: fec: adopt pinctrl support
ARM: ux500: switch MSP to using pinctrl for pins
ARM: ux500: alter MSP registration to return a device pointer
ARM: ux500: switch to using pinctrl for uart0
ARM: ux500: delete custom pin control system
ARM: ux500: switch over to Nomadik pinctrl driver
...
The nomadik gpio code has been converted to pinctrl, but the nomadik platform
still expects the old code to be present. Change it to use the new one instead.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=xjdL
-----END PGP SIGNATURE-----
Merge tag 'ux500-gpio-pins-for-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into next/pinctrl
ux500 GPIO and pinctrl changes for kernel 3.5
* tag 'ux500-gpio-pins-for-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ARM: ux500: switch MSP to using pinctrl for pins
ARM: ux500: alter MSP registration to return a device pointer
ARM: ux500: switch to using pinctrl for uart0
ARM: ux500: delete custom pin control system
ARM: ux500: switch over to Nomadik pinctrl driver
pinctrl: add sleep state definition
pinctrl/nomadik: implement pin configuration
pinctrl/nomadik: implement pin multiplexing
pinctrl/nomadik: reuse GPIO debug function for pins
pinctrl/nomadik: break out single GPIO debug function
pinctrl/nomadik: basic Nomadik pinctrl interface
pinctrl/nomadik: !CONFIG_OF build error
gpio: move the Nomadik GPIO driver to pinctrl
Context conflicts resolved in drivers/pinctrl/Kconfig and
drivers/pinctrl/Makefile.
Signed-off-by: Olof Johansson <olof@lixom.net>
Uwe Kleine-König