Commit Graph

167 Commits

Author SHA1 Message Date
Adrian Hunter af849c8610 mmc: sdhci: Handle auto-command errors
If the host controller supports auto-commands then enable the auto-command
error interrupt and handle it. In the case of auto-CMD23, the error is
treated the same as manual CMD23 error. In the case of auto-CMD12,
commands-during-transfer are not permitted, so the error handling is
treated the same as a data error.

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-12-17 08:26:24 +01:00
Adrian Hunter 869f8a69bb mmc: sdhci: Rename SDHCI_ACMD12_ERR and SDHCI_INT_ACMD12ERR
The SDHCI_ACMD12_ERR register is used for auto-CMD23 and auto-CMD12
errors, as is the SDHCI_INT_ACMD12ERR interrupt bit. Rename them to
SDHCI_AUTO_CMD_STATUS and SDHCI_INT_AUTO_CMD_ERR respectively.

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-12-17 08:26:24 +01:00
Chunyan Zhang 427b6514d0 mmc: sdhci: Add Auto CMD Auto Select support
As SD Host Controller Specification v4.10 documents:
Host Controller Version 4.10 defines this "Auto CMD Auto Select" mode.
Selection of Auto CMD depends on setting of CMD23 Enable in the Host
Control 2 register which indicates whether card supports CMD23. If CMD23
Enable =1, Auto CMD23 is used and if CMD23 Enable =0, Auto CMD12 is
used. In case of Version 4.10 or later, use of Auto CMD Auto Select is
recommended rather than use of Auto CMD12 Enable or Auto CMD23
Enable.

This patch add this new mode support.

Signed-off-by: Chunyan Zhang <zhang.chunyan@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-10-08 11:40:43 +02:00
Chunyan Zhang e65953d4a1 mmc: sdhci: Add 32-bit block count support for v4 mode
Host Controller Version 4.10 re-defines SDMA System Address register
as 32-bit Block Count for v4 mode, and SDMA uses ADMA System
Address register (05Fh-058h) instead if v4 mode is enabled. Also
when using 32-bit block count, 16-bit block count register need
to be set to zero.

Since using 32-bit Block Count would cause problems for auto-cmd23,
it can be chosen via host->quirk2.

Signed-off-by: Chunyan Zhang <zhang.chunyan@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-10-08 11:40:43 +02:00
Chunyan Zhang 685e444bba mmc: sdhci: Add ADMA2 64-bit addressing support for V4 mode
ADMA2 64-bit addressing support is divided into V3 mode and V4 mode.
So there are two kinds of descriptors for ADMA2 64-bit addressing
i.e. 96-bit Descriptor for V3 mode, and 128-bit Descriptor for V4
mode. 128-bit Descriptor is aligned to 8-byte.

For V4 mode, ADMA2 64-bit addressing is enabled via Host Control 2
register.

Signed-off-by: Chunyan Zhang <zhang.chunyan@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
[Ulf: Fixed conflict while applying]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-10-08 11:40:43 +02:00
Chunyan Zhang b3f80b434f mmc: sdhci: Add sd host v4 mode
For SD host controller version 4.00 or later ones, there're two
modes of implementation - Version 3.00 compatible mode or
Version 4 mode.  This patch introduced an interface to enable
v4 mode.

Signed-off-by: Chunyan Zhang <zhang.chunyan@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-10-08 11:40:43 +02:00
Chunyan Zhang 18da1990d2 mmc: sdhci: Add version V4 definition
Added definitions for v400, v410, v420.

Signed-off-by: Chunyan Zhang <zhang.chunyan@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-10-08 11:40:43 +02:00
Jisheng Zhang 54552e4948 mmc: sdhci: introduce adma_write_desc() hook to struct sdhci_ops
Add this hook so that it can be overridden with driver specific
implementations. We also let the original sdhci_adma_write_desc()
accept &desc so that the function can set its new value. Then export
the function so that it could be reused by driver's specific
implementations.

Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-10-08 11:40:43 +02:00
Jisheng Zhang e93be38af1 mmc: sdhci: add adma_table_cnt member to struct sdhci_host
This patch adds adma_table_cnt member to struct sdhci_host to give more
flexibility to drivers to control the ADMA table count.

Default value of adma_table_cnt is set to (SDHCI_MAX_SEGS * 2 + 1).

Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-10-08 11:40:43 +02:00
Aapo Vienamo d462c1b474 mmc: sdhci: Export sdhci_request()
Allow SDHCI drivers to hook code before and after sdhci_request() by
making it externally visible.

Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-10-08 11:40:43 +02:00
Yinbo Zhu 7d8bb1f46e mmc: sdhci: add tuning error codes
This patch is to add tuning error codes to
judge tuning state

Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-10-08 11:40:43 +02:00
ernest.zhang 6663c419a0 mmc: sdhci: Export sdhci tuning function symbol
Export sdhci tuning function symbols which are used by other SD Host
controller driver modules.

Signed-off-by: ernest.zhang <ernest.zhang@bayhubtech.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-07-30 14:25:06 +02:00
Kishon Vijay Abraham I fc1fa1b7db mmc: sdhci: Program a relatively accurate SW timeout value
sdhci has a 10 second timeout to catch devices that stop responding.
In the case of quirk SDHCI_QUIRK2_DISABLE_HW_TIMEOUT, instead of
programming 10 second arbitrary value, calculate the total time it would
take for the entire transfer to happen and program the timeout value
accordingly.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-05-03 09:36:20 +02:00
Adrian Hunter a999fd9392 mmc: sdhci: Add quirk to disable HW timeout
Add quirk to disable HW timeout if the requested timeout is more than the
maximum obtainable timeout.

Also, if the quirk is set and ->get_max_timeout_count() is not implemented,
max_busy_timeout is set to zero.

Based-on-patch-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-05-03 09:36:19 +02:00
Linus Walleij bd9b902798 mmc: sdhci: Implement an SDHCI-specific bounce buffer
The bounce buffer is gone from the MMC core, and now we found out
that there are some (crippled) i.MX boards out there that have broken
ADMA (cannot do scatter-gather), and also broken PIO so they must
use SDMA. Closer examination shows a less significant slowdown
also on SDMA-only capable Laptop hosts.

SDMA sets down the number of segments to one, so that each segment
gets turned into a singular request that ping-pongs to the block
layer before the next request/segment is issued.

Apparently it happens a lot that the block layer send requests
that include a lot of physically discontiguous segments. My guess
is that this phenomenon is coming from the file system.

These devices that cannot handle scatterlists in hardware can see
major benefits from a DMA-contiguous bounce buffer.

This patch accumulates those fragmented scatterlists in a physically
contiguous bounce buffer so that we can issue bigger DMA data chunks
to/from the card.

When tested with a PCI-integrated host (1217:8221) that
only supports SDMA:
0b:00.0 SD Host controller: O2 Micro, Inc. OZ600FJ0/OZ900FJ0/OZ600FJS
        SD/MMC Card Reader Controller (rev 05)
This patch gave ~1Mbyte/s improved throughput on large reads and
writes when testing using iozone than without the patch.

dmesg:
sdhci-pci 0000:0b:00.0: SDHCI controller found [1217:8221] (rev 5)
mmc0 bounce up to 128 segments into one, max segment size 65536 bytes
mmc0: SDHCI controller on PCI [0000:0b:00.0] using DMA

On the i.MX SDHCI controllers on the crippled i.MX 25 and i.MX 35
the patch restores the performance to what it was before we removed
the bounce buffers.

Cc: Pierre Ossman <pierre@ossman.eu>
Cc: Benoît Thébaudeau <benoit@wsystem.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Benjamin Beckmeyer <beckmeyer.b@rittal.de>
Cc: stable@vger.kernel.org # v4.14+
Fixes: de3ee99b09 ("mmc: Delete bounce buffer handling")
Tested-by: Benjamin Beckmeyer <beckmeyer.b@rittal.de>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-01-31 11:27:23 +01:00
Adrian Hunter 58e79b6075 mmc: sdhci: Handle failure of enable_irq_wake()
Now that sdhci_enable_irq_wakeups() is a local function, change it to
return whether the IRQ wakeup was successfully enabled. This is in
preparation for adding more conditions for whether IRQ wakeup is enabled.

Note it is assumed, for SDHCI devices, that suspend is more important than
wakeup, so we continue to suspend regardless.

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-01-17 12:30:43 +01:00
Adrian Hunter 551d6bde46 mmc: sdhci: Stop exporting sdhci_enable_irq_wakeups()
Now that it is not being used by any drivers, stop exporting it.

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2018-01-17 12:30:43 +01:00
Kishon Vijay Abraham I 1284c248d1 mmc: sdhci: Add quirk to indicate MMC_RSP_136 has CRC
TI's implementation of sdhci controller used in DRA7 SoC's has
CRC in responses with length 136 bits. Add quirk to indicate
the controller has CRC in MMC_RSP_136. If this quirk is
set sdhci library shouldn't shift the response present in
SDHCI_RESPONSE register.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-08-30 15:03:43 +02:00
Srinivas Kandagatla c846a00f72 mmc: sdhci: add sdma_boundary member to struct sdhci_host
This patch adds sdma_boundary member to struct sdhci_host to give more
flexibility to drivers to control the sdma boundary buffer value and
also to fix issue on some sdhci controllers which are broken when
HOST SDMA Buffer Boundary is programmed in Block Size Register (0x04)
when using ADMA. Qualcomm sdhci controller is one of such type, writing
to this bits is un-supported.

Default value of sdma_boundary is set to SDHCI_DEFAULT_BOUNDARY_ARG.

Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-08-30 14:01:54 +02:00
Adrian Hunter 83b600b8de mmc: sdhci: Control the delay between tuning commands
The delay between tuning commands for SD cards is not part of the
specification. A driver that needs it probably needs it for eMMC
too, whereas most drivers would probably like to set it to 0. Make
it a host member (host->tuning_delay) that defaults to the existing
behaviour. Drivers can set it to zero to eliminate the delay, or
set it to a positive value to always have a delay.

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-04-24 21:42:27 +02:00
Hu Ziji 2f05b6ab5f mmc: sdhci: Export sdhci_enable_sdio_irq() from sdhci.c
Export sdhci_enable_sdio_irq() from sdhci.c.
Thus vendor SDHC driver can implement its specific SDIO irq
control.

Signed-off-by: Hu Ziji <huziji@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-04-24 21:42:14 +02:00
Hu Ziji c376ea9e46 mmc: sdhci: Export sdhci_start_signal_voltage_switch() in sdhci.c
Export sdhci_start_signal_voltage_switch() from sdhci.c.
Thus vendor sdhci driver can implement its own signal voltage
switch routine.

Signed-off-by: Hu Ziji <huziji@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-04-24 21:42:14 +02:00
Hu Ziji 6a6d4ceb7b mmc: sdhci: Export sdhci_set_ios() from sdhci.c
Export sdhci_set_ios() in sdhci.c.
Thus vendor sdhci driver can implement its own set_ios() routine.

Signed-off-by: Hu Ziji <huziji@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-04-24 21:42:13 +02:00
Shawn Lin 8cc3528922 mmc: sdhci: clarify the get_timeout_clock callback
Currently the get_timeout_clock callback doesn't clearly
have a statement that it needs the variant drivers to return
the timeout clock rate in kHz if the SDHCI_TIMEOUT_CLK_UNIT
isn't present, otherwise the variant drivers should return it
in MHz. It's also very likely that further variant drivers which
are going to use this callback will be confused by this situation.
Given the fact that moderm sdhci variant hosts are very prone to get
the timeout clock from common clock framework (actually the only three
users did that), it's more natural to return the value in Hz and we
make an explicit comment there. Then we put the unit conversion inside
the sdhci core. Thus will improve the code and prevent further misuses.

Reported-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2017-04-24 21:41:48 +02:00
Adrian Hunter f12e39dbf3 mmc: sdhci: Add CQE support
Add an interrupt hook and helper functions for enabling, disabling and
delivering interrupts to a CQE.

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Ludovic Desroches <ludovic.desroches@microchip.com>
2017-04-24 21:41:36 +02:00
Adrian Hunter 4180ffa817 mmc: sdhci: Add sdhci_cleanup_host
Add sdhci_cleanup_host() to cleanup __sdhci_add_host().

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Ludovic Desroches <ludovic.desroches@microchip.com>
2017-04-24 21:41:34 +02:00
Adrian Hunter 15becf68b8 mmc: sdhci: Get rid of 'extern' in header file
Get rid of unnecessary 'extern' in header file.

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Ludovic Desroches <ludovic.desroches@microchip.com>
2017-04-24 21:41:34 +02:00
Adrian Hunter d28981727d mmc: sdhci: Export sdhci_dumpregs
Export sdhci_dumpregs so that it can be called by drivers.

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Ludovic Desroches <ludovic.desroches@microchip.com>
2017-04-24 21:41:33 +02:00
Adrian Hunter 0c62e6752d mmc: sdhci: Remove ->select_drive_strength() callback
Drivers can use the host operation directly, so remove this now unused
callback.

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Ludovic Desroches <ludovic.desroches@microchip.com>
2017-04-24 21:41:29 +02:00
Ulf Hansson b8789ec482 mmc: host: Include interrupt.h in mmc host drivers that depends on it
An mmc host driver shouldn't rely on interrupt.h being included by another
public mmc header. Instead make that dependency explicit by including
interrupt.h in those host drivers that depends on it.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
2017-02-13 13:20:01 +01:00
Ulf Hansson 210583f472 mmc: sdhci: Include leds.h
Don't rely on host.h to include the leds.h header, but instead include it
explicitly because the driver depends on it.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
2017-02-13 13:20:00 +01:00
Masahiro Yamada 85a882c2e9 mmc: sdhci: export sdhci_execute_tuning()
Some SDHCI-compat controllers support not only SD, but also eMMC,
but they use different commands for tuning: CMD19 for SD, CMD21 for
eMMC.

Due to the difference of the underlying mechanism, some controllers
(at least, the Cadence IP is the case) provide their own registers
for the eMMC tuning.

This commit will be useful when we want to override .execute_tuning
callback (for eMMC HS200 tuning), but still let it fall back to
sdhci_execute_tuning() for SD timing.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-12-08 15:02:45 +01:00
Ritesh Harjani fec7967397 mmc: sdhci: Factor out sdhci_enable_clk
Factor out sdhci_enable_clk from sdhci_set_clock
and make it EXPORT_SYMBOL so that it can be called.

Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-11-29 09:05:15 +01:00
Masahiro Yamada 178b0fa0d4 mmc: sdhci: remove unneeded (void *) casts in sdhci_(pltfm_)priv()
The type of host->private is (unsigned long *).  No cast is needed
to return an opaque pointer.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-11-29 09:01:00 +01:00
Michael Walle b0921d5c9e mmc: sdhci-of-esdhc: fixup PRESENT_STATE read
Since commit 87a18a6a56 ("mmc: mmc: Use ->card_busy() to detect busy
cards in __mmc_switch()") the ESDHC driver is broken:
  mmc0: Card stuck in programming state! __mmc_switch
  mmc0: error -110 whilst initialising MMC card

Since this commit __mmc_switch() uses ->card_busy(), which is
sdhci_card_busy() for the esdhc driver. sdhci_card_busy() uses the
PRESENT_STATE register, specifically the DAT0 signal level bit. But the
ESDHC uses a non-conformant PRESENT_STATE register, thus a read fixup is
required to make the driver work again.

Signed-off-by: Michael Walle <michael@walle.cc>
Fixes: 87a18a6a56 ("mmc: mmc: Use ->card_busy() to detect busy cards in __mmc_switch()")
Acked-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: <stable@vger.kernel.org> # v4.8+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-11-18 14:41:47 +01:00
Adrian Hunter 606d313124 mmc: sdhci: Rename sdhci_set_power() to sdhci_set_power_noreg()
Unlike other cases, sdhci_set_power() does not reflect the default
implementation of the ->set_power() callback. Rename it and create
sdhci_set_power() that is the default implementation.

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-10-10 14:20:41 +02:00
Zach Brown 3794c54264 mmc: sdhci-of-arasan: Set controller to test mode when no CD bit
The sdhci controller on xilinx zynq devices will not function unless
the CD bit is provided. http://www.xilinx.com/support/answers/61064.html
In cases where it is impossible to provide the CD bit in hardware,
setting the controller to test mode and then setting inserted to true
will get the controller to function without the CD bit.

When the device has the property xlnx,fails-without-test-cd the driver
changes the controller to test mode and sets test inserted to true to
make the controller function.

Signed-off-by: Zach Brown <zach.brown@ni.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-09-26 21:31:34 +02:00
Ulf Hansson 92add82e0c mmc: sdhci: Remove ->platform_init() callback as it's no longer used
The commit 1ef5e49e46 ("mmc: sdhci-of-esdhc: add/remove some quirks
according to vendor version") moved sdhci-of-esdhc away from using the
->platform_init() callback.

As it was the only user of it and that it seems reasonable to believe that
it won't be needed again, let's just remove it.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
2016-09-26 21:31:16 +02:00
Dong Aisheng f37b20ebc4 mmc: sdhci: add standard hw auto retuning support
If HW supports SDHCI_TUNING_MODE_3 which is auto retuning, we won't
retune during runtime suspend and resume, instead we use Re-tuning
Request signaled via SDHCI_INT_RETUNE interrupt to do retuning and
hw auto retuning during data transfer to guarantee the signal sample
window correction.

This can avoid a mass of repeatedly retuning during small file system
data access and improve the performance.

Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-07-25 10:34:55 +02:00
Stefan Wahren e71d4b816c mmc: sdhci: add define for suspend/resume capability
This patch adds the missing define for the suspend/resume
capability (according to SD Host Controller spec).

Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Scott Branden <scott.branden@broadcom.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-07-25 10:34:47 +02:00
Adrian Hunter 4e9f8fe5f2 mmc: sdhci: Allow for finishing multiple requests
In order to support commands during data transfer, there will have to be up
to two active requests (mrqs) at a time, instead of just one. That means
recording which request is finished.  Doing that obsoletes host->mrq which
is therefore removed.

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-07-25 10:34:43 +02:00
Adrian Hunter d7422fb489 mmc: sdhci: Separate timer timeout for command and data requests
In order to support commands during data transfer, there will have to be up
to two active requests (mrqs) at a time, instead of just one. Provide two
timers instead of just one. One of the timers is for requests that do not
use the data lines, and the other one is for requests that do.

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-07-25 10:34:43 +02:00
Adrian Hunter ed1563de0b mmc: sdhci: Track whether a reset is pending
SDHCI recovers from errors by resetting the cmd and data circuits. Until
that is done, there very well might be more interrupts, so ignore them in
that case.

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-07-25 10:34:41 +02:00
Adrian Hunter ea96802384 mmc: sdhci: Get rid of host->busy_handle
Now that there is host->data_cmd to record the command for which a data
interrupt is expected, it is possible to determine whether a command with
busy signaling has completed without an extra flag. So host->busy_handle
is not needed. Remove it.

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-07-25 10:34:38 +02:00
Adrian Hunter 7c89a3d908 mmc: sdhci: Record what command is using the data lines
In order to support commands during data transfer, there must be a
distinction between the command that is using the command line (and
for which a command interrupt is expected) and the command that is
using the data lines (for which a data interrupt is expected).

There is host->cmd for the command line, but there is only host->data
for the data lines, which is a different structure, does not represent
the command in use, and is anyway NULL in the case of commands that use
the data lines for busy signalling instead of data transfer.

Introduce host->data_cmd to record what command is using the data lines,
and use that instead of host->cmd when referring to the data command.

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-07-25 10:34:38 +02:00
Adrian Hunter 6132a3bf07 mmc: sdhci: Add sdhci_read_caps()
Add sdhci_read_caps() and __sdhci_read_caps() to make it easier for drivers
to fix the version and capabilities registers.

Pedantically, the SDHCI specification states that the capabilities
registers are valid when the host controller resets the Software Reset For
All bit. That requirement has always been satisfied by performing a reset
at the start of initialization, and consequently that is now part of the
new functions.

Although the SDHCI_QUIRK_MISSING_CAPS quirk has not yet been removed,
drivers that want to provide their own caps can now use these functions
instead of that quirk.

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-07-25 10:34:35 +02:00
Adrian Hunter 28da35899e mmc: sdhci: Tidy caps variables in sdhci_setup_host()
In preparation for adding a function to read the capability registers.

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-07-25 10:34:34 +02:00
Adrian Hunter 8cb851a4da mmc: sdhci: Make signal voltage support explicit
Signal voltage support is not a quirk, it is a capability. According to the
SDHCI specification, support for 1.8V signaling is determined by the
presence of one of the capability bits SDHCI_SUPPORT_SDR50,
SDHCI_SUPPORT_SDR104, or SDHCI_SUPPORT_DDR50. This is complicated by also
supporting eMMC which has 1.8V modes and 1.2V modes. It would be possible
to use the transfer mode to determine signal voltage support, except for
eMMC DDR52 mode which uses the same capability (MMC_CAP_1_8V_DDR) for 1.8V
signaling and 3V signaling.

In addition, the mmc core will fail over from one signaling voltage to the
next (refer mmc_power_up()) which means SDHCI really needs to validate
which voltages are actually supported.

Introduce SDHCI flags for signal voltage support and set them based on the
supported transfer modes. In general, drivers should prefer to set the
supported transfer modes correctly rather than change the signal voltage
capability, except in the case where 3V DDR52 is supported but 1.8V is
not.

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-07-25 10:34:34 +02:00
Adrian Hunter 52f5336db2 mmc: sdhci: Split sdhci_add_host()
Split sdhci-add_host() in order to further our objective to make
sdhci into a library.

The split divides code that sets up mmc and sdhci parameters, from
code that actually activates things - such as tasklet initialization,
requesting the irq, and adding (and starting) the host.

This gives drivers an opportunity to change various settings before
committing to start the host.

Drivers can continue to call sdhci_add_host() but drivers that want
to take advantage of the split instead call sdhci_setup_host() followed
by __sdhci_add_host().

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-07-25 10:34:33 +02:00
Masahiro Yamada 74479c5d50 mmc: sdhci: use IS_ENABLE(CONFIG_LEDS_CLASS) to enable LED struct members
defined(CONFIG_LEDS_CLASS) || defined(CONFIG_LEDS_CLASS_MODULE)

is equivalent to:

IS_ENABLED(CONFIG_LEDS_CLASS)

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-05-02 10:33:36 +02:00