Below is the changeset from the MPI specification and 2.00.34 header
files:
1) Defined additional bits in the BiosOptions field of BIOS Page 1 to
allow for finer control of X86 BIOS and UEFI BSD.
2) For the Clean Tool, reserved bit 26 of the Flags field for product
specific use.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
struct fusion_context *fusion is already memset to '0', so remove a
redundant call to memmset "fusion->load_balance_info" to '0'.
Signed-off-by: Chaitra Basappa <chaitra.basappa@avagotech.com>
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
1) For fusion adapters, limit reserved frames for non SCSI commands to 8
(3 for parallel IOCTLs + 5 for driver's internal DCMDs).
Earlier reserved commands for non SCSI IO frames was set to 32, so with
this implementation, increased per controller "can_queue".
Behavior of MFI controllers will remain unchanged.
2) Optimize the code related to per controller's 'can_queue' setting.
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Chaitra Basappa <chaitra.basappa@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Driver calls megasas_complete_cmd() to call wake_up() for each MFI frame
that was issued through the ioctl() interface prior to the kill adapter.
This ensures userspace ioctl() system calls issued just before a kill
adapter don't get stuck in wait state and IOCTLs are returned to
the application.
Cc: <stable@vger.kernel.org>
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Chaitra Basappa <chaitra.basappa@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Update driver "mask_interrupts" before enable/disable hardware interrupt
in order to avoid missing interrupts because of "mask_interrupts" still
set to 1 and hardware interrupts are enabled.
Cc: <stable@vger.kernel.org>
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Chaitra Basappa <chaitra.basappa@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This patch will address the issue of SCSI device created at OS level for
non existing VD. ldTgtIdtoLd[] array has size 256 for Extended VD firmware
and 128 for legacy firmware. Accessing indices beyond array size (OS will
send TUR, INQUIRY.. commands upto device index 255), may return valid LD
value and that particular SCSI command will be SUCCESS and creating SCSI
device for non existing target(VD).
For legacy firmware (64 VD firmware), invalidates LD (by setting LD value
to 0xff) in LdTgtIdtoLd[] array for device index beyond 127, so that
invalid LD(0xff) value should be returned beyond device index beyond 127.
Cc: <stable@vger.kernel.org>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This patch adds support for Secure Encrypting Drives (SED) in JBOD mode:
1) If the firmware supports SED JBOD, all non read/write commands to JBODs
will be sent via firmware path, and read/write commands to JBODs will
be sent via fastpath.
2) If the firmware does not support SED JBOD, driver will fall back to the
old design, i.e. send all JBOD I/O via fastpath.
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Chaitra Basappa <chaitra.basappa@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This patch addresses below issues:
1) Few endianness bug fixes.
2) Break the iteration after (MAX_LOGICAL_DRIVES_EXT - 1)),
instead of MAX_LOGICAL_DRIVES_EXT.
3) Optimization in MFI INIT frame before firing.
4) MFI IO frame should be 256bytes aligned. Code is optimized to reduce
the size of frame for fusion adapters and make the MFI frame size
calculation a bit transparent and readable.
Cc: <stable@vger.kernel.org>
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Signed-off-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: Chaitra Basappa <chaitra.basappa@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
It is not good practice to display the kernel pointer in any message logs,
and it doesn't display any additional information. And as we know have
block-layer assigned tags we can use them to differentiate the messages.
So remove any pointer references from the displayed messages.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
scsi_log_send() would display buffer pointer for higher logging levels.
This is not only of questionable value but also exposes kernel pointer to
userspace, which is discouraged in some setups. So drop this message
altogether.
Tested-by: Robert Elliott <elliott@hp.com>
Reviewed-by: Robert Elliott <elliott@hp.com>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Instead of having constants.c littered with ifdef statements we should
be moving dummy functions into the header and condintionally compile in
constants.c if selected. And update the Kconfig description to reflect
the actual size difference.
Suggested-by: Christoph Hellwig <hch@infradead.org>
Tested-by: Robert Elliott <elliott@hp.com>
Reviewed-by: Robert Elliott <elliott@hp.com>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Convert scsi_print_result() to use the per-cpu buffer for decoding the
command result and disposition.
Tested-by: Robert Elliott <elliott@hp.com>
Reviewed-by: Robert Elliott <elliott@hp.com>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Convert sense buffer logging to use the per-cpu buffer to avoid line
breakup.
Tested-by: Robert Elliott <elliott@hp.com>
Reviewed-by: Robert Elliott <elliott@hp.com>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
libata already uses an internal buffer, so we should be using
__scsi_format_command() here.
Tested-by: Robert Elliott <elliott@hp.com>
Reviewed-by: Robert Elliott <elliott@hp.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Use an external buffer for __scsi_print_command() and move command
logging over to use the per-cpu logging buffer. With that we can
guarantee the command always will always be formatted in one line.
So we can even print out a variable length command correctly across
several lines. Finally rename __scsi_print_command() to
__scsi_format_comment() to better reflect the functionality.
Tested-by: Robert Elliott <elliott@hp.com>
Reviewed-by: Robert Elliott <elliott@hp.com>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The request tag provides a concise identification of a SCSI
command, so we should be printing that out for scmd_printk().
Suggested-by: Christoph Hellwig <hch@lst.de>
Tested-by: Robert Elliott <elliott@hp.com>
Reviewed-by: Robert Elliott <elliott@hp.com>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Implement a per-cpu buffer for formatting messages to avoid line breaks
up under high load. This patch implements scmd_printk() and
sdev_prefix_printk() using the per-cpu buffer and makes sdev_printk() a
wrapper for sdev_prefix_printk().
Tested-by: Robert Elliott <elliott@hp.com>
Reviewed-by: Robert Elliott <elliott@hp.com>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
On win8 and win8 r2 hosts force SPC-3 compliance for MSFT virtual disks.
Ubuntu has been carrying a similar patch outside the tree for a while now.
Starting with win10, the host will support SPC-3 compliance. Based on all
the testing that has been done on win8 and win8 r2 hosts, we are comfortable
claiming SPC-3 compliance on these hosts as well. This will enable TRIM
support on these hosts.
Suggested by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Long Li <longli@microsoft.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Commit 4cd83ecdac changed the limits to
reflect the values on the host. It turns out that WS2008R2 cannot
correctly handle these new limits. Fix this bug by setting the limits
based on the host.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Long Li <longli@microsoft.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The host asks the guest to scan when a LUN is removed or added.
The only way a guest can identify the removed LUN is when an I/O is
attempted on a removed LUN - the SRB status code indicates that the LUN
is invalid. We currently handle this SRB status and remove the device.
Rather than waiting for an I/O to remove the device, force the discovery of
LUNs that may have been removed prior to discovering LUNs that may have
been added.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Long Li <longli@microsoft.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The virtual HBA that storvsc implements can support multiple channels and
targets. So, scan the host when the host notifies that a scan is needed.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Long Li <longli@microsoft.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
STORVSC uses its own momory pool to manage device request data. However,
the SCSI layer already has a mechanisim for allocating additional memory
for each command issued to device driver. This patch removes the memory
pool in STORVSC and makes it use SCSI layer to allocate memory for device
request data.
Reviewed-by: Long Li <longli@microsoft.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This patch, applicable to 8G/4G/2G adapters, adds a call that
resumes transmit operations after a link bounce. Without it, targets
that tried to suspend exchanges after a link bounce (such as tape devices
using sequence level error recovery) would never resume io operation,
causing scan failures, and eventually deadlocks if a device removal
request is made.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: Dick Kennedy <dick.kennedy@emulex.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
'num_tags' is an unsigned char, so the check for 'ESP_MAX_TAGS'
(which is set to 256) is pointless.
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The "issue_reset" can be used uninitialized. It should be set to false
at the start.
Also I cleaned up the types a little by using bool.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The "issue_reset" variable can be used uninitialized. It should be set
to false at the start.
Also I cleaned up the types by using bool.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Replacing strncpy with strlcpy to avoid strings that lacks null terminate.
And use the sizeof on the to string rather than strlen on the from string.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Acked-by: Adam Radford <aradford@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Accept the WRITE BUFFER command and do nothing other than
set the appropriate "microcode has been changed" UA on the LU.
>From an earlier patch by Doug Gilbert.
Signed-off-by: Ewan D. Milne <emilne@redhat.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Tested-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Generate a REPORTED LUNS DATA HAS CHANGED Unit Attention if
sysfs "max_luns" is used to change the number of scsi_debug LUNs.
This is only done if scsi_debug_scsi_level is SPC-3 or above.
Additionally, implement SPC-4 behavior which only generates
this Unit Attention on the first LUN on the target to receive
a command after the change. This condition is cleared when
a REPORT LUNS command is received.
Signed-off-by: Ewan D. Milne <emilne@redhat.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Tested-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Add power_status to SES device slot, so we can power on/off the
HDDs behind the enclosure.
Check firmware status in ses_set_* before sending control pages to
firmware.
Signed-off-by: Song Liu <songliubraving@fb.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Jens Axboe <axboe@fb.com>
Cc: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The name provided by firmware is in a vendor specific format, publish
the slot number to have a reliable mechanism for identifying slots
across firmware implementations. If the enclosure does not provide a
slot number fallback to the component number which is guaranteed unique,
and usually mirrors the slot number.
Cleaned up the unused ses_component.desc in the process.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
Reviewed-by: Jens Axboe <axboe@fb.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Export the NAA logical id for the enclosure. This is optionally
available from the sas_transport_class, but it is really a property of
the enclosure.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
Reviewed-by: Jens Axboe <axboe@fb.com>
Cc: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
In support of a /dev/disk/by-slot populated with data from the enclosure
and ses modules udev needs notification when the new interface
files/links are available. Otherwise, any udev rules specified for the
disk cannot assume that the enclosure topology has settled.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
Reviewed-by: Jens Axboe <axboe@fb.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The slot and address fields have a small window of instability when
userspace can read them before initialization. Separate
enclosure_component
allocation from registration.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
Reviewed-by: Jens Axboe <axboe@fb.com>
Cc: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Update scsi_report_lun_scan to initially always report up to 511 LUs,
as the previous default max_report_luns did. Retry in a loop if not
enough memory is available for the number of LUs reported. Parameter
max_report_luns is removed as it is no longer used.
Signed-off-by: Rob Evers <revers@redhat.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Fix kernel-doc warning in scsi_error.c:
Warning(..//drivers/scsi/scsi_error.c:887): No description found for parameter 'hostt'
Fixes: 883a030f98
(scsi: document scsi_try_to_abort_cmd)
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The last time these SCSI asc/ascq codes were synced with T10 was
2013/06/05. Sync the SCSI ASC/ASCQ number to string tables with those
found at http://www.t10.org/lists/asc-num.txt dated 2014/12/21.
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The blk-mq ->queue_rq method is always called from process context,
but might have preemption disabled. This means we still always
have to use GFP_ATOMIC for memory allocations, and thus need to
revert part of commit 3c356bde1 ("scsi: stop passing a gfp_mask
argument down the command setup path").
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reported-by: Sasha Levin <sasha.levin@oracle.com>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Tested-by: Alexei Starovoitov <alexei.starovoitov@gmail.com>
Commit e05fe29248 (qla2xxx: Honor FCP_RSP retry delay timer field.)
causes systems to busy-wait for about 3 minutes after boot prior to
detecting SAN disks.
During this wait period one kworker is running full-time
(though /proc/<pid>/stack has no useful data). Another kworker is
waiting for IO to complete during that whole time period.
Looking at drivers/scsi/qla2xxx/qla_os.c, fcport->retry_delay_timestamp
has a special value of 0 though that 0 value forces system to wait when
jiffies is very large value (e.g. 4294952605 - "negative" value when
signed on 32bit systems).
Signed-off-by: Bruno Prémont <bonbons@linux-vserver.org>
Acked-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Pull UML fixes from Richard Weinberger:
"Two fixes for UML regressions. Nothing exciting"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/uml:
x86, um: actually mark system call tables readonly
um: Skip futex_atomic_cmpxchg_inatomic() test
Commit a074335a37 ("x86, um: Mark system call tables readonly") was
supposed to mark the sys_call_table in UML as RO by adding the const,
but it doesn't have the desired effect as it's nevertheless being placed
into the data section since __cacheline_aligned enforces sys_call_table
being placed into .data..cacheline_aligned instead. We need to use
the ____cacheline_aligned version instead to fix this issue.
Before:
$ nm -v arch/x86/um/sys_call_table_64.o | grep -1 "sys_call_table"
U sys_writev
0000000000000000 D sys_call_table
0000000000000000 D syscall_table_size
After:
$ nm -v arch/x86/um/sys_call_table_64.o | grep -1 "sys_call_table"
U sys_writev
0000000000000000 R sys_call_table
0000000000000000 D syscall_table_size
Fixes: a074335a37 ("x86, um: Mark system call tables readonly")
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
futex_atomic_cmpxchg_inatomic() does not work on UML because
it triggers a copy_from_user() in kernel context.
On UML copy_from_user() can only be used if the kernel was called
by a real user space process such that UML can use ptrace()
to fetch the value.
Reported-by: Miklos Szeredi <miklos@szeredi.hu>
Suggested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Richard Weinberger <richard@nod.at>
Tested-by: Daniel Walter <d.walter@0x90.at>
This is a set of three fixes: one to correct an abort path thinko causing
failures (and a panic) in USB on device misbehaviour, One to fix an out of
order issue in the fnic driver and one to match discard expectations to qemu
which otherwise cause Linux to behave badly as a guest.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABAgAGBQJUpsmHAAoJEDeqqVYsXL0MdToH/1UsmOdtxNh6AfBDWWYi45o8
kBno1gTnRrDgIlOiRu+BtmL25A1rNcCdCQKjG6JBEBruqUVAwZztktGjfuSvso6s
EYbrnE+5DmDs6cW8pp6GK3QGV+R+AmbT8oBbe/Kpg5LdTsdnQOozSycUp7X3XgTi
pLOm6rW/AgEV1QFcQz1bjI6cnbcOZMcGZnC5qwphiKgBnVYd+PZY24RSHDKCu/va
z2lsa5yqXFHKZZZRhYG343YqCTf3Dkph78124JoNvVm3EjO+GQAAiojiUa7l59UF
RqNRqeMxfz2cPmBnJxbNmWiP1YQGBgOaNDRgc7D7SPxaMwUe9444Gm4MkoZWzmQ=
=706l
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is a set of three fixes: one to correct an abort path thinko
causing failures (and a panic) in USB on device misbehaviour, One to
fix an out of order issue in the fnic driver and one to match discard
expectations to qemu which otherwise cause Linux to behave badly as a
guest"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
SCSI: fix regression in scsi_send_eh_cmnd()
fnic: IOMMU Fault occurs when IO and abort IO is out of order
sd: tweak discard heuristics to work around QEMU SCSI issue
Nothing too exciting as a new year's start here: most of fixes are for
ASoC, a boot crash fix on OMAP for deferred probe, a few driver
specific fixes (Intel, dwc, rockchip, rt5677), in addition to typo
fixes in kerneldoc comments for PCM.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=ARQX
-----END PGP SIGNATURE-----
Merge tag 'sound-3.19-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Nothing too exciting as a new year's start here: most of fixes are for
ASoC, a boot crash fix on OMAP for deferred probe, a few driver
specific fixes (Intel, dwc, rockchip, rt5677), in addition to typo
fixes in kerneldoc comments for PCM"
* tag 'sound-3.19-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: pcm: Fix kerneldoc for params_*() functions
ASoC: rockchip: i2s: fix maxburst of dma data to 4
ASoC: rockchip: i2s: fix error defination of transmit data level
ASoC: Intel: correct the fixed free block allocation
ASoC: rt5677: fixed rt5677_dsp_vad_put rt5677_dsp_vad_get panic
ASoC: Intel: Fix BYTCR machine driver MODULE_ALIAS
ASoC: Intel: Fix BYTCR firmware name
ASoC: dwc: Iterate over all channels
ASoC: dwc: Ensure FIFOs are flushed to prevent channel swap
ASoC: Intel: Add I2C dependency to two new machines
ASoC: dapm: Remove snd_soc_of_parse_audio_routing() due to deferred probe
There's a single change here, fixing a vhost bug where vhost initialization
fails due to used ring alignment check being too strict.
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUoRcnAAoJECgfDbjSjVRpb7IIAIGoNJkB56Q3WWX0rP5i1Lqi
Uxt8lrvySotzoWMVZlm2pGRiwJv2T1dQXKWetvZDn0GuwCBi2/vm2l4eOhu1K+VV
jOtKk8n8kDJVgMOGaJUwqt8lhDbqGwHHDUCKDk78/pV5Q959bAVo143vWOh2DixQ
m3YmvmLwyhF6CYNwOD0HqllaojDPBAP3k22GdmJNy/H7CpcOSYK7BRoiQHX7FsbR
I3Kj/7gf5OlZFzLTLxNx/O01p1BkX6EusADfl3+tl6nggc6vqW9fHNz/TZLGh9I/
ap0Ng3pm8q/t6S6wsPj8wzTHNesK4gVWvecRN8kZV8UQY2rwd/y7R/k+VpJDseg=
=+Pmi
-----END PGP SIGNATURE-----
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull vhost cleanup and virtio bugfix
"There's a single change here, fixing a vhost bug where vhost
initialization fails due to used ring alignment check being too
strict"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
vhost: relax used address alignment
virtio_ring: document alignment requirements
Sreekanth Reddy