- Delete some unused U8540 UART platform data.
- MMC/SD-fixes from Ulf Hansson so everything works with
the device tree again.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJSzBk0AAoJEEEQszewGV1zNocP/ib50Xx8PgUZISdD8Waq8Yvr
NGu+vYAU+YQpCUbsxNY4UtXzkvvOeRyaLtt3MwefiEaFpB4YDSRXWXdOe9HSE599
Oc6Q1FckoV6soyu/Bm9uyClxKqxlzFN4zv3hoKpm9SUxT51BHWfYMkd2nKE1yy/F
uroyPb1BhX5PX+65yFzn7qwuPIfbBsk8cr34YbHHvEmeLPdJXCp7I0sx+PY3AX80
DSfVQPOIFv2Y+lGwnF9FOmtloM5gv8bcxmH2NPLPWE8xoXCODY/3iME5thSOP4vq
uIb0bfkgh26y9zZzK/SX355f/PTc2mfbneFRvHUP/cuzPC83aHeg5U/aQVB5k00P
0DHhKlJuiDUVHJldhkg3IcweyEL+MCfbCfffGAZWhmdvOw/RO/ptNYT7XXdN/YXM
zI9gURLzFeyknApEGAdBt3YX//hcMQh1VKVpaIV1dlNzUXNrulnX8p86ma15x5LD
Ht/ShWbWD1F6efEt0wQ6KFh8E2ZagZVaAXAgHjuyjCbC69NduVzeiJHIxk+/DJ0p
msWBq6agQ2GcF7Y1fQCtG1/6w1E11OaXmIQym04hI5mupeOwrbmutRNiTjsgpgfT
0spyka9G2fXwNwvcayC7jNGxUo6hQoUcp5SKZpBQOucoBBV9D3IRvnrbFErpagE0
0TFWoIrYcP75Tc7LzJO5
=vC9c
-----END PGP SIGNATURE-----
Merge tag 'ux500-devicetree-v3.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into next/dt
From Linus Walleij:
Ux500 device tree patches for v3.14, take 2
- Delete some unused U8540 UART platform data.
- MMC/SD-fixes from Ulf Hansson so everything works with
the device tree again.
* tag 'ux500-devicetree-v3.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ARM: ux500: regulators: Remove dead code for SD-card regulator
ARM: ux500: Configure regulator for I/O voltage for SD-card slot
ARM: ux500: Refactor common DT configs for sdi[n] devices
ARM: ux500: delete U8540 UART auxdata
Signed-off-by: Olof Johansson <olof@lixom.net>
When building for CONFIG_SUSPEND, add the platform suspend callbacks
to enable system suspend for ux500.
At this initial step, only WFI state is supported, which is reached
for both PM_SUSPEND_MEM and PM_SUSPEND_STANDBY.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The signal-voltage regulator is handled through a gpio regulator
configured in DT. Remove the old dead code.
Cc: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The other Ux500's does not need this anymore, and the U8540
certainly is no different.
Cc: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We have a handy macro to replace open coded __cpuc_flush_dcache_area(()
and outer_clean_range() sequences. Let's use it. No functional change.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
This reverts commit 49c129519a.
The special settings for the SD/MMC card parameters that are not
yet fully agreed upon how to encode into the device tree went missing
with this commit. We need to first put it into the device tree,
and then remove the platform data.
Cc: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This reverts commit ce16feb851.
This commit stopped tying down the name of the MMC/SD devices, but these
names are used in the pin control table, so the MMC/SD cards stopped
working.
Cc: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Rely solely on device tree matching to detect and probe the
SMP TWD timer and remove this custom hack.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Decomission the non-DT boot path as we are now DT only
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Decomission io_mapping() and device init calls from
non-DT boot path.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Decomission the AMBA device register functions.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This removes the unused inclusion of
<linux/platform_data/pinctrl-nomadik.h> which is
the last user in the entire kernel of this platform
data header.
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This deletes the AUXDATA hammering down the Nomadik pin
controller name to "pinctrl-db8500". We have removed all
dependencies on this name.
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This deletes a few final pin configuration macros from the
ux500.
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Move the few remaining snowball pin configurations to the device
tree, reference these as hogs to the pin controller until there
are real devices that can make use of them.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The SPI0 block is not at all connected to the AB8500 on the
Snowball: it is connected to the external header. These pins
on the header may also be used for GPIO, but let's assume
that SPI is a probable usecase on the Snowball and mux in the
SPI block and use these for SPI.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This transfers the muxing and biasing of the ethernet-related
pins on the snowball over to the device tree.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Move the few remaining HREFv60 pin configurations to the device
tree, reference these as hogs to the pin controller until there
are real devices that can make use of them.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Put two extra configs into the device tree to handle the default
configuration of the display reset signals on the HREFv60plus,
move this over from the board file to the device tree.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Move the control of muxing and enabling the IPGPIO (image
processor GPIO) from the static set-up to the device tree.
Use a hog as we have no device for the flash controller yet.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This moves some of the pin setup related to the CW1200 WLAN
module over to the device tree. As the driver is not yet
activated for the CW1200 WLAN we do not assign this pinctrl
state to any device node yet.
Get rid of the cmdline argument passing of a certain U9500
platform variant, as this is not supported by the kernel or
any device tree.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This moves over the configuration of the GPIO keys (used for
proximity sensor and Hall effect sensor) from the static pin
configuration file to the device tree. As part of the exercise,
implement the GPIO keys properly in a per-UIB file as this
setup actually differs with each UIB.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The old HREFs (MOP500) were controlling an image-processor
GPIO (IPGPIO) by using hogs. Do the same thing with device tree
and get rid of the mop500_pins setting.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pin mappings for the STM (System Trace Macrocell) are not
really used by anything: we have no driver for is and the settings
are not connected to any device. We can recreate the different
mux outputs in the device tree the day we need them. Drop these
for now.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This moves the SKE keypad pin control table out of the board
file and into the device tree. This was previously set to be
active on all MOP500 and HREF boards but after reading the
schematic this seems incorrect: the HREFv60 and later uses
one of these for MC5 and no reference designs have the SKE
connected to any hardware so just leave the pins alone
in the power-on state.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This moves the MCDE pin control table out of the board file
and into the device tree. Some pins and configs have been
marked as used by sub-devices or slaves to the MCDE, such
as I2C device 0-070 which is the HDMI interface circuit
AV8100, but the pins rather belong to the MCDE SOC block
as they come out of the main ASIC. The touch screen GPIO
is not related to MCDE so this gets deleted and need to
be tied to the respective touch screen (I2C) device
once that device is added instead.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This moves the SPI pin control table out of the board file
and into the device tree. Move the specific setting for
SSP0 on the HREFprev60 into the prev60-specific DTS file.
The SPI2 configuration is not really connected to any device,
as it will conflict with GPIO218 which is used on all HREFs.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This moves the MUSB pin control table out of the board file
and into the device tree. Tie the config to the on-chip MUSB
device rather than the ab8500-usb device which is off-chip.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This moves the input-pulled-up setting for GPIO217 as used
on the HREFs prior to v60 from the boardfile to the device
tree. GPIO218 is only used with the TVK UIB so move it to
that .dtsi file.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This moves the static, device-tied pin control configuration
out of the board file board-mop500-pins.c and into the device
tree. Add nodes for MSP0 and MSP2 on the HREF and Snowball
so we can reference the pins properly.
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This moves the static, device-tied pin control configuration
out of the board file board-mop500-pins.c and into the device
tree. Add entries for SDI1 and SDI2 on the Snowball so that the
WLAN pins on SDI1 can be used further on, and the unused pins
on SDI2 can be put to sleep.
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This moves the static, device-tied pin control configuration
out of the board file board-mop500-pins.c and into the device
tree. Define possible states also for I2C4 even if it's not
used by any board file at this time.
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This moves the static, device-tied pin control configuration
out of the board file board-mop500-pins.c and into the device
tree.
We create a new .dtsi-file to be shared between all the
MOP500-related boards, that include all HREF variants and
the Snowball board. Assign pin states for HREF and Snowball
boards alike.
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Move the platform data from all these files into one, delete empty
files and remove all references to them.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This hasn't been used since we converted the platform to DT only.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- New power capping framework and the the Intel Running Average Power
Limit (RAPL) driver using it from Srinivas Pandruvada and Jacob Pan.
- Addition of the in-kernel switching feature to the arm_big_little
cpufreq driver from Viresh Kumar and Nicolas Pitre.
- cpufreq support for iMac G5 from Aaro Koskinen.
- Baytrail processors support for intel_pstate from Dirk Brandewie.
- cpufreq support for Midway/ECX-2000 from Mark Langsdorf.
- ARM vexpress/TC2 cpufreq support from Sudeep KarkadaNagesha.
- ACPI power management support for the I2C and SPI bus types from
Mika Westerberg and Lv Zheng.
- cpufreq core fixes and cleanups from Viresh Kumar, Srivatsa S Bhat,
Stratos Karafotis, Xiaoguang Chen, Lan Tianyu.
- cpufreq drivers updates (mostly fixes and cleanups) from Viresh Kumar,
Aaro Koskinen, Jungseok Lee, Sudeep KarkadaNagesha, Lukasz Majewski,
Manish Badarkhe, Hans-Christian Egtvedt, Evgeny Kapaev.
- intel_pstate updates from Dirk Brandewie and Adrian Huang.
- ACPICA update to version 20130927 includig fixes and cleanups and
some reduction of divergences between the ACPICA code in the kernel
and ACPICA upstream in order to improve the automatic ACPICA patch
generation process. From Bob Moore, Lv Zheng, Tomasz Nowicki,
Naresh Bhat, Bjorn Helgaas, David E Box.
- ACPI IPMI driver fixes and cleanups from Lv Zheng.
- ACPI hotplug fixes and cleanups from Bjorn Helgaas, Toshi Kani,
Zhang Yanfei, Rafael J Wysocki.
- Conversion of the ACPI AC driver to the platform bus type and
multiple driver fixes and cleanups related to ACPI from Zhang Rui.
- ACPI processor driver fixes and cleanups from Hanjun Guo, Jiang Liu,
Bartlomiej Zolnierkiewicz, Mathieu Rhéaume, Rafael J Wysocki.
- Fixes and cleanups and new blacklist entries related to the ACPI
video support from Aaron Lu, Felipe Contreras, Lennart Poettering,
Kirill Tkhai.
- cpuidle core cleanups from Viresh Kumar and Lorenzo Pieralisi.
- cpuidle drivers fixes and cleanups from Daniel Lezcano, Jingoo Han,
Bartlomiej Zolnierkiewicz, Prarit Bhargava.
- devfreq updates from Sachin Kamat, Dan Carpenter, Manish Badarkhe.
- Operation Performance Points (OPP) core updates from Nishanth Menon.
- Runtime power management core fix from Rafael J Wysocki and update
from Ulf Hansson.
- Hibernation fixes from Aaron Lu and Rafael J Wysocki.
- Device suspend/resume lockup detection mechanism from Benoit Goby.
- Removal of unused proc directories created for various ACPI drivers
from Lan Tianyu.
- ACPI LPSS driver fix and new device IDs for the ACPI platform scan
handler from Heikki Krogerus and Jarkko Nikula.
- New ACPI _OSI blacklist entry for Toshiba NB100 from Levente Kurusa.
- Assorted fixes and cleanups related to ACPI from Andy Shevchenko,
Al Stone, Bartlomiej Zolnierkiewicz, Colin Ian King, Dan Carpenter,
Felipe Contreras, Jianguo Wu, Lan Tianyu, Yinghai Lu, Mathias Krause,
Liu Chuansheng.
- Assorted PM fixes and cleanups from Andy Shevchenko, Thierry Reding,
Jean-Christophe Plagniol-Villard.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=JCxk
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael J Wysocki:
- New power capping framework and the the Intel Running Average Power
Limit (RAPL) driver using it from Srinivas Pandruvada and Jacob Pan.
- Addition of the in-kernel switching feature to the arm_big_little
cpufreq driver from Viresh Kumar and Nicolas Pitre.
- cpufreq support for iMac G5 from Aaro Koskinen.
- Baytrail processors support for intel_pstate from Dirk Brandewie.
- cpufreq support for Midway/ECX-2000 from Mark Langsdorf.
- ARM vexpress/TC2 cpufreq support from Sudeep KarkadaNagesha.
- ACPI power management support for the I2C and SPI bus types from Mika
Westerberg and Lv Zheng.
- cpufreq core fixes and cleanups from Viresh Kumar, Srivatsa S Bhat,
Stratos Karafotis, Xiaoguang Chen, Lan Tianyu.
- cpufreq drivers updates (mostly fixes and cleanups) from Viresh
Kumar, Aaro Koskinen, Jungseok Lee, Sudeep KarkadaNagesha, Lukasz
Majewski, Manish Badarkhe, Hans-Christian Egtvedt, Evgeny Kapaev.
- intel_pstate updates from Dirk Brandewie and Adrian Huang.
- ACPICA update to version 20130927 includig fixes and cleanups and
some reduction of divergences between the ACPICA code in the kernel
and ACPICA upstream in order to improve the automatic ACPICA patch
generation process. From Bob Moore, Lv Zheng, Tomasz Nowicki, Naresh
Bhat, Bjorn Helgaas, David E Box.
- ACPI IPMI driver fixes and cleanups from Lv Zheng.
- ACPI hotplug fixes and cleanups from Bjorn Helgaas, Toshi Kani, Zhang
Yanfei, Rafael J Wysocki.
- Conversion of the ACPI AC driver to the platform bus type and
multiple driver fixes and cleanups related to ACPI from Zhang Rui.
- ACPI processor driver fixes and cleanups from Hanjun Guo, Jiang Liu,
Bartlomiej Zolnierkiewicz, Mathieu Rhéaume, Rafael J Wysocki.
- Fixes and cleanups and new blacklist entries related to the ACPI
video support from Aaron Lu, Felipe Contreras, Lennart Poettering,
Kirill Tkhai.
- cpuidle core cleanups from Viresh Kumar and Lorenzo Pieralisi.
- cpuidle drivers fixes and cleanups from Daniel Lezcano, Jingoo Han,
Bartlomiej Zolnierkiewicz, Prarit Bhargava.
- devfreq updates from Sachin Kamat, Dan Carpenter, Manish Badarkhe.
- Operation Performance Points (OPP) core updates from Nishanth Menon.
- Runtime power management core fix from Rafael J Wysocki and update
from Ulf Hansson.
- Hibernation fixes from Aaron Lu and Rafael J Wysocki.
- Device suspend/resume lockup detection mechanism from Benoit Goby.
- Removal of unused proc directories created for various ACPI drivers
from Lan Tianyu.
- ACPI LPSS driver fix and new device IDs for the ACPI platform scan
handler from Heikki Krogerus and Jarkko Nikula.
- New ACPI _OSI blacklist entry for Toshiba NB100 from Levente Kurusa.
- Assorted fixes and cleanups related to ACPI from Andy Shevchenko, Al
Stone, Bartlomiej Zolnierkiewicz, Colin Ian King, Dan Carpenter,
Felipe Contreras, Jianguo Wu, Lan Tianyu, Yinghai Lu, Mathias Krause,
Liu Chuansheng.
- Assorted PM fixes and cleanups from Andy Shevchenko, Thierry Reding,
Jean-Christophe Plagniol-Villard.
* tag 'pm+acpi-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (386 commits)
cpufreq: conservative: fix requested_freq reduction issue
ACPI / hotplug: Consolidate deferred execution of ACPI hotplug routines
PM / runtime: Use pm_runtime_put_sync() in __device_release_driver()
ACPI / event: remove unneeded NULL pointer check
Revert "ACPI / video: Ignore BIOS initial backlight value for HP 250 G1"
ACPI / video: Quirk initial backlight level 0
ACPI / video: Fix initial level validity test
intel_pstate: skip the driver if ACPI has power mgmt option
PM / hibernate: Avoid overflow in hibernate_preallocate_memory()
ACPI / hotplug: Do not execute "insert in progress" _OST
ACPI / hotplug: Carry out PCI root eject directly
ACPI / hotplug: Merge device hot-removal routines
ACPI / hotplug: Make acpi_bus_hot_remove_device() internal
ACPI / hotplug: Simplify device ejection routines
ACPI / hotplug: Fix handle_root_bridge_removal()
ACPI / hotplug: Refuse to hot-remove all objects with disabled hotplug
ACPI / scan: Start matching drivers after trying scan handlers
ACPI: Remove acpi_pci_slot_init() headers from internal.h
ACPI / blacklist: fix name of ThinkPad Edge E530
PowerCap: Fix build error with option -Werror=format-security
...
Conflicts:
arch/arm/mach-omap2/opp.c
drivers/Kconfig
drivers/spi/spi.c
Most of this branch consists of updates, additions and general churn of
the device tree source files in the kernel (arch/arm/boot/dts). Besides
that, there are a few things to point out:
- Lots of platform conversion on OMAP2+, with removal of old board files
for various platforms.
- Final conversion of a bunch of ux500 (ST-Ericsson) platforms as well
- Some updates to pinctrl and other subsystems. Most of these are for
DT-enablement of the various platforms and acks have been collected.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=nH67
-----END PGP SIGNATURE-----
Merge tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC DT updates from Olof Johansson:
"Most of this branch consists of updates, additions and general churn
of the device tree source files in the kernel (arch/arm/boot/dts).
Besides that, there are a few things to point out:
- Lots of platform conversion on OMAP2+, with removal of old board
files for various platforms.
- Final conversion of a bunch of ux500 (ST-Ericsson) platforms as
well
- Some updates to pinctrl and other subsystems. Most of these are
for DT-enablement of the various platforms and acks have been
collected"
* tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (385 commits)
ARM: dts: bcm11351: Use GIC/IRQ defines for sdio interrupts
ARM: dts: bcm: Add missing UARTs for bcm11351 (bcm281xx)
ARM: dts: bcm281xx: Add card detect GPIO
ARM: dts: rename ARCH_BCM to ARCH_BCM_MOBILE (dt)
ARM: bcm281xx: Add device node for the GPIO controller
ARM: mvebu: Add Netgear ReadyNAS 104 board
ARM: tegra: fix Tegra114 IOMMU register address
ARM: kirkwood: add support for OpenBlocks A7 platform
ARM: dts: omap4-panda: add DPI pinmuxing
ARM: dts: AM33xx: Add RNG node
ARM: dts: AM33XX: Add hwspinlock node
ARM: dts: OMAP5: Add hwspinlock node
ARM: dts: OMAP4: Add hwspinlock node
ARM: dts: use 'status' property for PCIe nodes
ARM: dts: sirf: add missed address-cells and size-cells for prima2 I2C
ARM: dts: sirf: add missed cell, cs and dma channel for SPI nodes
ARM: dts: sirf: add missed graphics2d iobg in atlas6 dts
ARM: dts: sirf: add missed chhifbg node in prima2 and atlas6 dts
ARM: dts: sirf: add missed memcontrol-monitor node in prima2 and atlas6 dts
ARM: mvebu: Add the core-divider clock to Armada 370/XP
...
CONFIG_CPU_FREQ_TABLE will be always enabled when cpufreq framework is used, as
cpufreq core depends on it. So, we don't need this CONFIG option anymore as it
is not configurable. Remove CONFIG_CPU_FREQ_TABLE and update its users.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
CLKDEV_LOOKUP selects HAVE_CLK and COMMON_CLK selects CLKDEV_LOOKUP. So
all symbols that select at least two of these symbols can be simplified.
For imx, omap2 and ux500 some rearrangements were necessary before the
simplification.
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Dinh Nguyen <dinguyen@altera.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Pawel Moll <pawel.moll@arm.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
- Move all the clock definitions over to the device tree
- Remove all now-redundant AUXDATA and make the ux500 device
tree only
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=FQfo
-----END PGP SIGNATURE-----
Merge tag 'ux500-dt-for-v3.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into next/dt
From Linus Walleij:
This is a huge device tree and ATAG removal series for ux500:
- Move all the clock definitions over to the device tree
- Remove all now-redundant AUXDATA and make the ux500 device
tree only
* tag 'ux500-dt-for-v3.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson: (92 commits)
ARM: ux500: delete devices-common remnants
clk: ux500: Provide a look-up for the ARMSS clock
ARM: ux500: Enable CPUFreq on Snowball
ARM: ux500: Provide a Device Tree node for CPUFreq in the DBx500
ARM: ux500: Provide a clock lookup for the Hash driver
ARM: ux500: Provide a clock lookup for the Crypto driver
ARM: ux500: Fix trivial white-space error in the DBX500 DTSI file
ARM: ux500: Remove ATAG booting support for Snowball
ARM: ux500: Remove ATAG booting support for HREF
ARM: ux500: Remove ATAG booting support for U8520
ARM: ux500: Remove ATAG booting support for MOP500
ARM: ux500: Purge UIB framework when booting with ATAGs
ARM: ux500: Take out STUIB support when not booting with Device Tree
ARM: ux500: Remove BU21013 ROHM TS support when booting with only ATAGs
ARM: ux500: Don't register the STMPE/SKE when booting with ATAG support
ARM: ux500: Delete U8500 UIB support when booting with ATAGs
ARM: ux500: Don't register Synaptics RMI4 TS when booting with ATAGs
ARM: ux500: Purge DB8500 PRCMU registration when not booting with DT
ARM: ux500: Stop requesting the SoC device to play 'parent' role
ARM: ux500: Remove UART support when booting without Device Tree
...
Signed-off-by: Olof Johansson <olof@lixom.net>
commit f1ff5b2549
"ARM: ux500: Stop enabling GPIOs when not booting with Device Tree"
deleted devices-common.c, but did not delete the build
rule from Makefile (most likely due to compiling in
a dirty tree where the object file still existed so
linking would complete anyway).
Delete the makerule, the header file associated
with this file and the remaining reference to the header.
Cc: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It's time to remove all ATAG support from ux500 and rely solely on
Device Tree booting. This patch is part of that endeavour.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It's time to remove all ATAG support from ux500 and rely solely on
Device Tree booting. This patch is part of that endeavour.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It's time to remove all ATAG support from ux500 and rely solely on
Device Tree booting. This patch is part of that endeavour.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It's time to remove all ATAG support from ux500 and rely solely on
Device Tree booting. This patch is part of that endeavour.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It's time to remove all ATAG support from ux500 and rely solely on
Device Tree booting. This patch is part of that endeavour.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It's time to remove all ATAG support from ux500 and rely solely on
Device Tree booting. This patch is part of that endeavour.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It's time to remove all ATAG support from ux500 and rely solely on
Device Tree booting. This patch is part of that endeavour.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It's time to remove all ATAG support from ux500 and rely solely on
Device Tree booting. This patch is part of that endeavour.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It's time to remove all ATAG support from ux500 and rely solely on
Device Tree booting. This patch is part of that endeavour.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It's time to remove all ATAG support from ux500 and rely solely on
Device Tree booting. This patch is part of that endeavour.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It's time to remove all ATAG support from ux500 and rely solely on
Device Tree booting. This patch is part of that endeavour.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There are no more devices which require left to register which require
a parent. This is part of the ux500 conversion over to Device Tree only
booting.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It's time to remove all ATAG support from ux500 and rely solely on
Device Tree booting. This patch is part of that endeavour.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It's time to remove all ATAG support from ux500 and rely solely on
Device Tree booting. This patch is part of that endeavour.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It's time to remove all ATAG support from ux500 and rely solely on
Device Tree booting. This patch is part of that endeavour.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It's time to remove all ATAG support from ux500 and rely solely on
Device Tree booting. This patch is part of that endeavour.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It's time to remove all ATAG support from ux500 and rely solely on
Device Tree booting. This patch is part of that endeavour.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It's time to remove all ATAG support from ux500 and rely solely on
Device Tree booting. This patch is part of that endeavour.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It's time to remove all ATAG support from ux500 and rely solely on
Device Tree booting. This patch is part of that endeavour.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It's time to remove all ATAG support from ux500 and rely solely on
Device Tree booting. This patch is part of that endeavour.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It's time to remove all ATAG support from ux500 and rely solely on
Device Tree booting. This patch is part of that endeavour.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This is part of the ux500 conversion over to Device Tree only
booting, but this stuff haven't been used for years.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It's time to remove all ATAG support from ux500 and rely solely on
Device Tree booting. This patch is part of that endeavour.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It's time to remove all ATAG support from ux500 and rely solely on
Device Tree booting. This patch is part of that endeavour.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It's time to remove all ATAG support from ux500 and rely solely on
Device Tree booting. This patch is part of that endeavour.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It's time to remove all ATAG support from ux500 and rely solely on
Device Tree booting. This patch is part of that endeavour.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It's time to remove all ATAG support from ux500 and rely solely on
Device Tree booting. This patch is part of that endeavour.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It's time to remove all ATAG support from ux500 and rely solely on
Device Tree booting. This patch is part of that endeavour.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It's time to remove all ATAG support from ux500 and rely solely on
Device Tree booting. This patch is part of that endeavour.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It's time to remove all ATAG support from ux500 and rely solely on
Device Tree booting. This patch is part of that endeavour.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It's time to remove all ATAG support from ux500 and rely solely on
Device Tree booting. This patch is part of that endeavour.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It's time to remove all ATAG support from ux500 and rely solely on
Device Tree booting. This patch is part of that endeavour.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It's time to remove all ATAG support from ux500 and rely solely on
Device Tree booting. This patch is part of that endeavour.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It's time to remove all ATAG support from ux500 and rely solely on
Device Tree booting. This patch is part of that endeavour.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It's time to remove all ATAG support from ux500 and rely solely on
Device Tree booting. This patch is part of that endeavour.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It's time to remove all ATAG support from ux500 and rely solely on
Device Tree booting. This patch is part of that endeavour.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It's time to remove all ATAG support from ux500 and rely solely on
Device Tree booting. This patch is part of that endeavour.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It's time to remove all ATAG support from ux500 and rely solely on
Device Tree booting. This patch is part of that endeavour.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It's time to remove all ATAG support from ux500 and rely solely on
Device Tree booting. This patch is part of that endeavour.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It's time to remove all ATAG support from ux500 and rely solely on
Device Tree booting. This patch is part of that endeavour.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We still need to utilise the AUXDATA system for the PRCMU to pass
through platform data which can not be DT:ed i.e. regulator initialisation
values. All we're doing in this patch is changing the comment header to be
more accurate.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
MSP no longer requires clock-name bindings, so we need to move them to
a more appropriate header indicating that we're still passing DMA
related platform data to them.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The ux500 platform will soon be converted to Device Tree only. When that
happens the old clock initialisation will be ripped out. In the meantime
however, we have to make a decision and call the appropriate
initialisation code manually.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When booting with DT enabled we already call clocksource_of_init(),
which in turn calls the OF version of nmdk_timer_init().
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This fixes a multiplatform regression on the Ux500.
When compiling the Ux500 platforms in multiplatform configurations
both PL310_ERRATA_588369 and PL310_ERRATA_727915 would crash the
platform when trying to launch the init process.
The Ux500 cannot access the debug registers of the PL310, it will
just crash if you try this. So disable this by setting the debug
callback to NULL when initializing the l2x0 on this platform.
Cc: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
These are changes that arrived a little late before the merge window,
or had dependencies on previous branches.
Highlights:
- ux500: misc. cleanup, fixup I2C devices
- exynos: DT updates for RTC; PM updates
- at91: DT updates for NAND; new platforms added to generic defconfig
- sunxi: DT updates: cubieboard2, pinctrl driver, gated clocks
- highbank: LPAE fixes, select necessary ARM errata
- omap: PM fixes and improvements; OMAP5 mailbox support
- omap: basic support for new DRA7xx SoCs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJSLkf1AAoJEFk3GJrT+8ZlF7oP/AyxrdRFyC1YmuOqzFH0/JTQ
EVBmMBiH+f1IKBT6YRkWCzX4JI5oOi+2DhrM6d/UPfbpr6pwd8dptuPiyLuBBUEm
byNbiJEYHidm23oFpKM+89tTHXbBrrz8XQN2xLwYhNr24QkVAsLTxyOjVA7KJM59
tk1tPQzO1ORyiFd485eQa3V4z98JgcE3QFNthbS7Y72wEXBzMZQDc9nFaoIJ5mHW
nzJSZyV24ibeEJeM2nsc7a3OvCyUfAQaO5Cio2UvdkGzZcmtxjxc1LjHa4VjIL6h
hwz+gqIOfl3hXotbjJxTp9+Ezt4TGU5bB3NUweE1btHE/KIEu0bx4hSsOz/kooA9
2JL8BCCTx+KiGiNHmNCcT679n9q11iOwqOWvxxhcJFkiV/6+mkjwTD9TNwR1q+RG
+LtOZr9tMcu2v/DbAivDYKiROmNCZhxpn35DoUKpBy73SOvJOiTLtSYitVN/tyM3
nWLEP5aTf3NwrWr8nFFws6ycwhgTCX0ITbdFD/fMlLMamHYPkckJ/0NXXOxfGiLk
kCMbdrCX4YTbCftmAQhrbdaPJVnE/SZI3CTJfutj8eX6NC2fm/U7Hcf5PI+W0Igd
moN/PaUULpVZI5hUrADyU1HCQnA97pv0biYVwzW5pBIt2u9tzUritabuERxPt9fa
SdHj0+u+xq9d3y35Oq46
=NIZZ
-----END PGP SIGNATURE-----
Merge tag 'late-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC late changes from Kevin Hilman:
"These are changes that arrived a little late before the merge window,
or had dependencies on previous branches.
Highlights:
- ux500: misc. cleanup, fixup I2C devices
- exynos: DT updates for RTC; PM updates
- at91: DT updates for NAND; new platforms added to generic defconfig
- sunxi: DT updates: cubieboard2, pinctrl driver, gated clocks
- highbank: LPAE fixes, select necessary ARM errata
- omap: PM fixes and improvements; OMAP5 mailbox support
- omap: basic support for new DRA7xx SoCs"
* tag 'late-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (60 commits)
ARM: dts: vexpress: Add CCI node to TC2 device-tree
ARM: EXYNOS: Skip C1 cpuidle state for exynos5440
ARM: EXYNOS: always enable PM domains support for EXYNOS4X12
ARM: highbank: clean-up some unused includes
ARM: sun7i: Enable the A20 clocks in the DTSI
ARM: sun6i: Enable clock support in the DTSI
ARM: sun5i: dt: Use the A10s gates in the DTSI
ARM: at91: at91_dt_defconfig: enable rm9200 support
ARM: dts: add ADC device tree node for exynos5420/5250
ARM: dts: Add RTC DT node to Exynos5420 SoC
ARM: dts: Update the "status" property of RTC DT node for Exynos5250 SoC
ARM: dts: Fix the RTC DT node name for Exynos5250
irqchip: mmp: avoid to include irqs head file
ARM: mmp: avoid to include head file in mach-mmp
irqchip: mmp: support irqchip
irqchip: move mmp irq driver
ARM: OMAP: AM33xx: clock: Add RNG clock data
ARM: OMAP: TI81XX: add always-on powerdomain for TI81XX
ARM: OMAP4: clock: Lock PLLs in the right sequence
ARM: OMAP: AM33XX: hwmod: Add hwmod data for debugSS
...
This branch contains mostly additions and changes to platform enablement
and SoC-level drivers. Since there's sometimes a dependency on device-tree
changes, there's also a fair amount of those in this branch.
Pieces worth mentioning are:
- Mbus driver for Marvell platforms, allowing kernel configuration
and resource allocation of on-chip peripherals.
- Enablement of the mbus infrastructure from Marvell PCI-e drivers.
- Preparation of MSI support for Marvell platforms.
- Addition of new PCI-e host controller driver for Tegra platforms
- Some churn caused by sharing of macro names between i.MX 6Q and 6DL
platforms in the device tree sources and header files.
- Various suspend/PM updates for Tegra, including LP1 support.
- Versatile Express support for MCPM, part of big little support.
- Allwinner platform support for A20 and A31 SoCs (dual and quad Cortex-A7)
- OMAP2+ support for DRA7, a new Cortex-A15-based SoC.
The code that touches other architectures are patches moving
MSI arch-specific functions over to weak symbols and removal of
ARCH_SUPPORTS_MSI, acked by PCI maintainers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=fJ5x
-----END PGP SIGNATURE-----
Merge tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform changes from Olof Johansson:
"This branch contains mostly additions and changes to platform
enablement and SoC-level drivers. Since there's sometimes a
dependency on device-tree changes, there's also a fair amount of
those in this branch.
Pieces worth mentioning are:
- Mbus driver for Marvell platforms, allowing kernel configuration
and resource allocation of on-chip peripherals.
- Enablement of the mbus infrastructure from Marvell PCI-e drivers.
- Preparation of MSI support for Marvell platforms.
- Addition of new PCI-e host controller driver for Tegra platforms
- Some churn caused by sharing of macro names between i.MX 6Q and 6DL
platforms in the device tree sources and header files.
- Various suspend/PM updates for Tegra, including LP1 support.
- Versatile Express support for MCPM, part of big little support.
- Allwinner platform support for A20 and A31 SoCs (dual and quad
Cortex-A7)
- OMAP2+ support for DRA7, a new Cortex-A15-based SoC.
The code that touches other architectures are patches moving MSI
arch-specific functions over to weak symbols and removal of
ARCH_SUPPORTS_MSI, acked by PCI maintainers"
* tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (266 commits)
tegra-cpuidle: provide stub when !CONFIG_CPU_IDLE
PCI: tegra: replace devm_request_and_ioremap by devm_ioremap_resource
ARM: tegra: Drop ARCH_SUPPORTS_MSI and sort list
ARM: dts: vf610-twr: enable i2c0 device
ARM: dts: i.MX51: Add one more I2C2 pinmux entry
ARM: dts: i.MX51: Move pins configuration under "iomuxc" label
ARM: dtsi: imx6qdl-sabresd: Add USB OTG vbus pin to pinctrl_hog
ARM: dtsi: imx6qdl-sabresd: Add USB host 1 VBUS regulator
ARM: dts: imx27-phytec-phycore-som: Enable AUDMUX
ARM: dts: i.MX27: Disable AUDMUX in the template
ARM: dts: wandboard: Add support for SDIO bcm4329
ARM: i.MX5 clocks: Remove optional clock setup (CKIH1) from i.MX51 template
ARM: dts: imx53-qsb: Make USBH1 functional
ARM i.MX6Q: dts: Enable I2C1 with EEPROM and PMIC on Phytec phyFLEX-i.MX6 Ouad module
ARM i.MX6Q: dts: Enable SPI NOR flash on Phytec phyFLEX-i.MX6 Ouad module
ARM: dts: imx6qdl-sabresd: Add touchscreen support
ARM: imx: add ocram clock for imx53
ARM: dts: imx: ocram size is different between imx6q and imx6dl
ARM: dts: imx27-phytec-phycore-som: Fix regulator settings
ARM: dts: i.MX27: Remove clock name from CPU node
...
Device tree and bindings updates for 3.12.
General additions of various on-chip and on-board peripherals on various
platforms as support gets added. Some of the bigger changes are:
- Addition of (new) PCI-e support on Tegra.
- More Tegra4 support, including PMC configuration for Dalmore.
- Addition of a new board for Exynos4 (trats2) and more bindings for 4x12 IP.
- Addition of Allwinner A20 and A31 SoC and board files.
- Move of the ST Ericsson device tree files to now use ste-* prefix.
- More move of hardware description of shmobile platforms to DT.
- Two new board dts files for Freescale MXs.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=1GuI
-----END PGP SIGNATURE-----
Merge tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC DT updates from Olof Johansson:
"Device tree and bindings updates for 3.12.
General additions of various on-chip and on-board peripherals on
various platforms as support gets added. Some of the bigger changes
are:
- Addition of (new) PCI-e support on Tegra.
- More Tegra4 support, including PMC configuration for Dalmore.
- Addition of a new board for Exynos4 (trats2) and more bindings for
4x12 IP.
- Addition of Allwinner A20 and A31 SoC and board files.
- Move of the ST Ericsson device tree files to now use ste-* prefix.
- More move of hardware description of shmobile platforms to DT.
- Two new board dts files for Freescale MXs"
* tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (177 commits)
dts: Rename DW APB timer compatible strings
dts: Deprecate ALTR as a vendor prefix
of: add vendor prefix for Altera Corp.
ARM: at91/dt: sam9x5ek: add sound configuration
ARM: at91/dt: sam9x5ek: enable SSC
ARM: at91/dt: sam9x5ek: add WM8731 codec
ARM: at91/dt: sam9x5: add SSC DMA parameters
ARM: at91/dt: add at91rm9200 PQFP package version
ARM: at91: at91rm9200: set default mmc0 pinctrl-names
ARM: at91: at91sam9n12: correct pin number of gpio-key
ARM: at91: at91sam9n12: add qt1070 support
ARM: at91: at91sam9n12: add pinctrl of TWI
ARM: at91: Add PMU support for sama5d3
ARM: at91: at91sam9260: add missing pinctrl-names on mmc
ARM: tegra: configure power off for Dalmore
ARM: DT: binding fixup to align with vendor-prefixes.txt (DT)
ARM: dts: add sdio blocks to bcm28155-ap board
ARM: dts: align sdio numbers to HW definition
ARM: sun7i: Add Olimex A20-Olinuxino-Micro support
ARM: sun7i: Add Allwinner A20 DTSI
...
This branch contains code cleanups, moves and removals for 3.12.
There's a large number of various cleanups, and a nice net removal of
13500 lines of code.
Highlights worth mentioning are:
- A series of patches from Stephen Boyd removing the ARM local timer API.
- Move of Qualcomm MSM IOMMU code to drivers/iommu.
- Samsung PWM driver cleanups from Tomasz Figa, removing legacy PWM driver
and switching over to the drivers/pwm one.
- Removal of some unusued auto-generated headers for OMAP2+ (PRM/CM).
There's also a move of a header file out of include/linux/i2c/ to
platform_data, where it really belongs. It touches mostly ARM platform
code for include changes so we took it through our tree.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=1vE4
-----END PGP SIGNATURE-----
Merge tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"This branch contains code cleanups, moves and removals for 3.12.
There's a large number of various cleanups, and a nice net removal of
13500 lines of code.
Highlights worth mentioning are:
- A series of patches from Stephen Boyd removing the ARM local timer
API.
- Move of Qualcomm MSM IOMMU code to drivers/iommu.
- Samsung PWM driver cleanups from Tomasz Figa, removing legacy PWM
driver and switching over to the drivers/pwm one.
- Removal of some unusued auto-generated headers for OMAP2+ (PRM/CM).
There's also a move of a header file out of include/linux/i2c/ to
platform_data, where it really belongs. It touches mostly ARM
platform code for include changes so we took it through our tree"
* tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (83 commits)
ARM: OMAP2+: Add back the define for AM33XX_RST_GLOBAL_WARM_SW_MASK
gpio: (gpio-pca953x) move header to linux/platform_data/
arm: zynq: hotplug: Remove unreachable code
ARM: SAMSUNG: Remove unnecessary exynos4_default_sdhci*()
tegra: simplify use of devm_ioremap_resource
ARM: SAMSUNG: Remove plat/regs-timer.h header
ARM: SAMSUNG: Remove remaining uses of plat/regs-timer.h header
ARM: SAMSUNG: Remove pwm-clock infrastructure
ARM: SAMSUNG: Remove old PWM timer platform devices
pwm: Remove superseded pwm-samsung-legacy driver
ARM: SAMSUNG: Modify board files to use new PWM platform device
ARM: SAMSUNG: Rework private data handling in dev-backlight
pwm: Add new pwm-samsung driver
ARM: mach-mvebu: remove redundant DT parsing and validation
ARM: msm: Only compile io.c on platforms that use it
iommu/msm: Move mach includes to iommu directory
ARM: msm: Remove devices-iommu.c
ARM: msm: Move mach/board.h contents to common.h
ARM: msm: Migrate msm_timer to CLOCKSOURCE_OF_DECLARE
ARM: msm: Remove TMR and TMR0 static mappings
...
development cycle:
- Various cleanups like remove non-existant hardware from
the Snowball device tree, prefix all files with "ste-*"
- External regulators
- Documentation updates
- Delete some minor dangling platform data
- Pin control settings for U8540 through DT
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)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=Wm2y
-----END PGP SIGNATURE-----
Merge tag 'ux500-devicetree-for-v3.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into next/dt
From: Linus Walleij:
Ux500 device tree enablement base for the v3.12
development cycle:
- Various cleanups like remove non-existant hardware from
the Snowball device tree, prefix all files with "ste-*"
- External regulators
- Documentation updates
- Delete some minor dangling platform data
- Pin control settings for U8540 through DT
* tag 'ux500-devicetree-for-v3.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson: (22 commits)
ARM: ux500: fix devicetree builds
ARM: ux500: Remove u9540.dts as it's been replaced
ARM: ux500: Apply a ste-* prefix onto dbx5x0.dtsi
ARM: ux500: Apply a ste-* prefix onto stuib.dtsi
ARM: ux500: Apply a ste-* prefix onto hrefv60plus.dts
ARM: ux500: Apply a ste-* prefix onto hrefprev60.dts Signed-off-by: Lee Jones <lee.jones@linaro.org>
ARM: ux500: Apply a ste-* prefix onto href.dtsi
ARM: ux500: Apply a ste-* prefix onto ccu9540.dts
ARM: ux500: Apply a ste-* prefix onto ccu8540.dts
ARM: ux500: Apply a ste-* prefix onto snowball.dts
ARM: ux500: Remove Snowball DTS entry for ROHM BH1780GLI ambient light sensor
ARM: ux500: Remove Snowball DTS entry for TPS61052 chip
ARM: ux500: Remove Snowball DTS entry for National Semiconductor LP5521 LED chip
ARM: ux500: Remove Toshiba TC35892 I/O Expander's DT entry from Snowball's DTS
ARM: u8540: DT: Set pinctrl mapping to i2c0,1,2,4 & 5
ARM: u8540: Add Pinctrl Device Tree settings for uart0, uart2
ARM: ux500: Stop passing MMC's platform data for Device Tree boots
Documentation: Update binding for Nomadik and DBx5x based platforms
ARM: ux500: Supply external regulator names for Snowball's DT
ARM: ux500: Provide a supply name for the AB8500 AUX regulators to use
...
The I2C device registration on the different ux500 board was
buggy due to a switch to dynamically assigned I2C host
addresses. This I2C host is still there, but we have to add
the devices dynamically instead of using board data.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pin definition file dates back to a time before the pin
control subsystem. The functions called inside that pin control
driver are now deleted. Let's get rid of this file.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Replace ARRAY_AND_SIZE(e) in function argument position to avoid hiding the
arity of the called function.
The semantic match that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e,f;
@@
f(...,
- ARRAY_AND_SIZE(e)
+ e,ARRAY_SIZE(e)
,...)
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Set coherent_dma_mask to DMA_BIT_MASK(32) for dma40 platform_device, as
without this DMA allocations were failing with the error:
dma40 dma40.0: coherent DMA mask is unset
when booting without device-tree.
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch removes u8500_secondary_startup from _INIT section, there are
two reason for this removal.
1. discarding such a small code does not save much, given the RAM sizes.
2. Having this code discarded, creates corruption issue when we boot
smp-kernel with nr_cpus=1 or with single cpu node in DT.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It was required to pass DMA channel configuration information to the
MMC driver before the new DMA API was in place. Now that it is, and
is fully compatible with Device Tree we can stop doing that.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There is no more dependency with arch/arm headers, so we can safely move the
driver to the drivers/cpuidle directory.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
The db8500-regs.h file does not need to be included by the cpuidle
driver.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
To break the dependency on the "id.h" file we move the cpuidle driver
to a platform device. Now we only call the probe() on this driver if
we find a corresponding platform device (which is spawned from the
PRCMU MFD driver).
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
timer API entirely. Doing so will reduce code in ARM core, reduce the
architecture dependencies of our timer drivers, and simplify the code because
we no longer go through an architecture layer that is essentially a hotplug
notifier.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=wZbm
-----END PGP SIGNATURE-----
Merge tag 'remove-local-timers' of git://git.kernel.org/pub/scm/linux/kernel/git/davidb/linux-msm into next/cleanup
From Stephen Boyd:
Now that we have a generic arch hook for broadcast we can remove the
local timer API entirely. Doing so will reduce code in ARM core, reduce
the architecture dependencies of our timer drivers, and simplify the code
because we no longer go through an architecture layer that is essentially
a hotplug notifier.
* tag 'remove-local-timers' of git://git.kernel.org/pub/scm/linux/kernel/git/davidb/linux-msm:
ARM: smp: Remove local timer API
clocksource: time-armada-370-xp: Divorce from local timer API
clocksource: time-armada-370-xp: Fix sparse warning
ARM: msm: Divorce msm_timer from local timer API
ARM: PRIMA2: Divorce timer-marco from local timer API
ARM: EXYNOS4: Divorce mct from local timer API
ARM: OMAP2+: Divorce from local timer API
ARM: smp_twd: Divorce smp_twd from local timer API
ARM: smp: Remove duplicate dummy timer implementation
Resolved a large number of conflicts due to __cpuinit cleanups, etc.
Signed-off-by: Olof Johansson <olof@lixom.net>
The __cpuinit type of throwaway sections might have made sense
some time ago when RAM was more constrained, but now the savings
do not offset the cost and complications. For example, the fix in
commit 5e427ec2d0 ("x86: Fix bit corruption at CPU resume time")
is a good example of the nasty type of bugs that can be created
with improper use of the various __init prefixes.
After a discussion on LKML[1] it was decided that cpuinit should go
the way of devinit and be phased out. Once all the users are gone,
we can then finally remove the macros themselves from linux/init.h.
Note that some harmless section mismatch warnings may result, since
notify_cpu_starting() and cpu_up() are arch independent (kernel/cpu.c)
and are flagged as __cpuinit -- so if we remove the __cpuinit from
the arch specific callers, we will also get section mismatch warnings.
As an intermediate step, we intend to turn the linux/init.h cpuinit
related content into no-ops as early as possible, since that will get
rid of these warnings. In any case, they are temporary and harmless.
This removes all the ARM uses of the __cpuinit macros from C code,
and all __CPUINIT from assembly code. It also had two ".previous"
section statements that were paired off against __CPUINIT
(aka .section ".cpuinit.text") that also get removed here.
[1] https://lkml.org/lkml/2013/5/20/589
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Will Deacon <will.deacon@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
across several different platforms and architectures, fixes to existing
drivers, a MAINTAINERS file fix and improvements to the basic clock
types that allow them to be of use to more platforms than before. Only a
few fixes to the core framework are included with most all of the
changes landing in the various clock drivers themselves.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=SwMB
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus-3.11' of git://git.linaro.org/people/mturquette/linux
Pull clock framework updates from Mike Turquette:
"The common clock framework changes for 3.11 include new clock drivers
across several different platforms and architectures, fixes to
existing drivers, a MAINTAINERS file fix and improvements to the basic
clock types that allow them to be of use to more platforms than before.
Only a few fixes to the core framework are included with most all of
the changes landing in the various clock drivers themselves."
* tag 'clk-for-linus-3.11' of git://git.linaro.org/people/mturquette/linux: (55 commits)
clk: tegra: fix ifdef for tegra_periph_reset_assert inline
clk: tegra: provide tegra_periph_reset_assert alternative
clk: exynos4: Fix clock aliases for cpufreq related clocks
clk: samsung: Add MUX_FA macro to pass flag and alias
clk: add support for Rockchip gate clocks
clk: vexpress: Make the clock drivers directly available for arm64
clk: vexpress: Use full node name to identify individual clocks
clk: tegra: T114: add DFLL DVCO reset control
clk: tegra: T114: add DFLL source clocks
clk: tegra: T114: add FCPU clock shaper programming, needed by the DFLL
clk: gate: add CLK_GATE_HIWORD_MASK
clk: divider: add CLK_DIVIDER_HIWORD_MASK flag
clk: mux: add CLK_MUX_HIWORD_MASK
clk: Always notify whole subtree when reparenting
MAINTAINERS: make drivers/clk entry match subdirs
clk: honor CLK_GET_RATE_NOCACHE in clk_set_rate
clk: use clk_get_rate() for debugfs
clk: tegra: Use override bits when needed
clk: tegra: override bits for Tegra30 PLLM
clk: tegra: override bits for Tegra114 PLLM
...
These are changes that arrived a little late before the merge
window or that have multiple dependencies on previous branches
so they did not fit into one of the earlier ones. There
are 10 branches merged here, a total of 39 non-merge commits.
Contents are a mixed bag for the above reasons:
* Two new SoC platforms: ST microelectronics stixxxx and
the TI 'Nspire' graphing calculator. These should have
been in the 'soc' branch but were a little late
* Support for the Exynos 5420 variant in mach-exynos,
which is based on the other exynos branches to avoid
conflicts.
* Various small changes for sh-mobile, ux500 and davinci
* Common clk support for MSM
Conflicts:
* In Kconfig.debug, various additions trivially conflict,
the list should be kept in alphabetical order when
resolving.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=cRu2
-----END PGP SIGNATURE-----
Merge tag 'late-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC late changes from Arnd Bergmann:
"These are changes that arrived a little late before the merge window
or that have multiple dependencies on previous branches so they did
not fit into one of the earlier ones. There are 10 branches merged
here, a total of 39 non-merge commits. Contents are a mixed bag for
the above reasons:
* Two new SoC platforms: ST microelectronics stixxxx and the TI
'Nspire' graphing calculator. These should have been in the 'soc'
branch but were a little late
* Support for the Exynos 5420 variant in mach-exynos, which is based
on the other exynos branches to avoid conflicts.
* Various small changes for sh-mobile, ux500 and davinci
* Common clk support for MSM"
* tag 'late-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (39 commits)
ARM: ux500: bail out on alien cpus
ARM: davinci: da850: adopt to pinctrl-single change for configuring multiple pins
serial: sh-sci: Initialise variables before access in sci_set_termios()
ARM: stih41x: Add B2020 board support
ARM: stih41x: Add B2000 board support
ARM: sti: Add DEBUG_LL console support
ARM: sti: Add STiH416 SOC support
ARM: sti: Add STiH415 SOC support
ARM: msm: Migrate to common clock framework
ARM: msm: Make proc_comm clock control into a platform driver
ARM: msm: Prepare clk_get() users in mach-msm for clock-pcom driver
ARM: msm: Remove clock-7x30.h include file
ARM: msm: Remove custom clk_set_{max,min}_rate() API
ARM: msm: Remove custom clk_set_flags() API
msm: iommu: Use clk_set_rate() instead of clk_set_min_rate()
msm: iommu: Convert to clk_prepare/unprepare
msm_sdcc: Convert to clk_prepare/unprepare
usb: otg: msm: Convert to clk_prepare/unprepare
msm_serial: Use devm_clk_get() and properly return errors
msm_serial: Convert to clk_prepare/unprepare
...
These changes are all driver specific and cross over between arm-soc
contents and some other subsystem, in these cases cpufreq, crypto,
dma, pinctrl, mailbox and usb, and the subsystem owners agreed to
have these changes merged through arm-soc. As we proceed to untangle
the dependencies between platform code and driver code, the amount of
changes in this category is fortunately shrinking, for 3.11 we have
16 branches here and 101 non-merge changesets, the majority of which
are for the stedma40 dma engine driver used in the ux500 platform.
Cleaning up that code touches multiple subsystems, but gets rid
of the dependency in the end.
The mailbox code moved out from mach-omap2 to drivers/mailbox
is an intermediate step and is still omap specific at the moment.
Patches exist to generalize the subsystem and add other drivers
with the same API, but those did not make it for 3.11.
Conflicts:
* In cpu-db8500.c results from the removal of the u8500_of_init_devices
function in combination with the split of u8500_auxdata_lookup.
* In arch/arm/mach-omap2/devices.c, the includes got reshuffled.
we need to keep linux/wl12xx.h and linux/platform_data/mailbox-omap.h.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=mJsI
-----END PGP SIGNATURE-----
Merge tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver specific changes from Arnd Bergmann:
"These changes are all driver specific and cross over between arm-soc
contents and some other subsystem, in these cases cpufreq, crypto,
dma, pinctrl, mailbox and usb, and the subsystem owners agreed to have
these changes merged through arm-soc.
As we proceed to untangle the dependencies between platform code and
driver code, the amount of changes in this category is fortunately
shrinking, for 3.11 we have 16 branches here and 101 non-merge
changesets, the majority of which are for the stedma40 dma engine
driver used in the ux500 platform. Cleaning up that code touches
multiple subsystems, but gets rid of the dependency in the end.
The mailbox code moved out from mach-omap2 to drivers/mailbox is an
intermediate step and is still omap specific at the moment. Patches
exist to generalize the subsystem and add other drivers with the same
API, but those did not make it for 3.11."
* tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (101 commits)
crypto: ux500: use dmaengine_submit API
crypto: ux500: use dmaengine_prep_slave_sg API
crypto: ux500: use dmaengine_device_control API
crypto: ux500/crypt: add missing __iomem qualifiers
crypto: ux500/hash: add missing static qualifiers
crypto: ux500/hash: use readl on iomem addresses
dmaengine: ste_dma40: Declare memcpy config as static
ARM: ux500: Remove mop500_snowball_ethernet_clock_enable()
ARM: ux500: Correct the EN_3v3 regulator's on/off GPIO
ARM: ux500: Provide a AB8500 GPIO Device Tree node
gpio: rcar: fix gpio_rcar_of_table
gpio-rcar: Remove #ifdef CONFIG_OF around OF-specific sections
gpio-rcar: Reference core gpio documentation in the DT bindings
clk: exynos5250: Add enum entries for divider clock of i2s1 and i2s2
ARM: dts: Update Samsung I2S documentation
ARM: dts: add clock provider information for i2s controllers in Exynos5250
ARM: dts: add Exynos audio subsystem clock controller node
clk: samsung: register audio subsystem clocks using common clock framework
ARM: dts: use #include for all device trees for Samsung
pinctrl: s3c24xx: use correct header for chained_irq functions
...
These changes from 30 individual branches for the most part update device
tree files, but there are also a few source code changes that have crept
in this time, usually in order to atomically move over a driver from
using hardcoded data to DT probing.
A number of platforms change their DT files to use the C preprocessor,
which is causing a bit of churn, but that is hopefully only this once.
There are a few conflicts with the other branches unfortunately:
* in exynos5440.dtsi and kirkwood-6281.dtsi, device nodes are added
from multiple branches. Need to be careful to have the right
set of closing braces as git gets this one wrong.
* In kirkwood.dtsi, one 'ranges' line got split into two lines, while
another line got added. Order of the lines does not matter.
* in sama5d3.dtsi, some cleanup was merged the wrong way, causing
a bogus conflict. We want the 'dmas' and 'dma-names' properties
to get added here.
* Two lines got removed independently in arch/arm/mach-mxs/mach-mxs.c
* Contents get added independently in arch/arm/mach-omap2/cclock33xx_data.c
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=8PtJ
-----END PGP SIGNATURE-----
Merge tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC device tree changes from Arnd Bergmann:
"These changes from 30 individual branches for the most part update
device tree files, but there are also a few source code changes that
have crept in this time, usually in order to atomically move over a
driver from using hardcoded data to DT probing.
A number of platforms change their DT files to use the C preprocessor,
which is causing a bit of churn, but that is hopefully only this once"
* tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (372 commits)
ARM: at91: dt: rm9200ek: add spi support
ARM: at91: dt: rm9200: add spi support
ARM: at91/DT: at91sam9n12: add SPI DMA client infos
ARM: at91/DT: sama5d3: add SPI DMA client infos
ARM: at91/DT: fix SPI compatibility string
ARM: Kirkwood: Fix the internal register ranges translation
ARM: dts: bcm281xx: change comment to C89 style
ARM: mmc: bcm281xx SDHCI driver (dt mods)
ARM: nomadik: add the new clocks to the device tree
clk: nomadik: implement the Nomadik clocks properly
ARM: dts: omap5-uevm: Provide USB Host PHY clock frequency
ARM: dts: omap4-panda: Fix DVI EDID reads
ARM: dts: omap4-panda: Add USB Host support
arm: mvebu: enable mini-PCIe connectors on Armada 370 RD
ARM: shmobile: irqpin: add a DT property to enable masking on parent
ARM: dts: AM43x EPOS EVM support
ARM: dts: OMAP5: Add bandgap DT entry
ARM: dts: AM33XX: Add pinmux configuration for CPSW to am335x EVM
ARM: dts: AM33XX: Add pinmux configuration for CPSW to EVMsk
ARM: dts: AM33XX: Add pinmux configuration for CPSW to beaglebone
...
This makes the l2x0 initialization fail gracefully on non-ux500
systems.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Separate the smp_twd timers from the local timer API. This will
allow us to remove ARM local timer support in the near future and
gets us closer to moving this driver to drivers/clocksource.
Tested-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Patches from Lee Jones:
This gets rid of mop500_snowball_ethernet_clock_enable() which is no
longer in use. It also straightens out a bug which ensures the SMSC911x's
regulator is turned on at start-up when using Device Tree.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
mop500_snowball_ethernet_clock_enable() provided a means to enable a
clock which was used for the SMSC911x Ethernet device on Snowball. It
was merely a stand-in until the driver was common clk compliant. Now
that it is, this can be removed for both DT and ATAGs booting.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
tapering down finally as we're getting closer to making
omap2+ DT only.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=5gWz
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.11/board-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/boards
From Tony Lindgren:
Minor board changes for v3.11 merge window. These are
tapering down finally as we're getting closer to making
omap2+ DT only.
* tag 'omap-for-v3.11/board-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: omap2plus_defconfig: enable USB_PHY and NOP_USB_XCEIV
ARM: OMAP1: nokia770: enable Tahvo
ARM: OMAP3EVM: Marking omap3_evm_display_init() with CONFIG_BROKEN
arm: omap: board-overo: reset GPIO for SMSC911x
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Removes the following warnings:
arch/arm/mach-ux500/board-mop500-pins.c:51:6: warning: 'slpm_in_nopull_wkup' defined but not used [-Wunused-variable]
arch/arm/mach-ux500/board-mop500-pins.c:63:6: warning: 'slpm_out_lo_wkup' defined but not used [-Wunused-variable]
Signed-off-by: Olof Johansson <olof@lixom.net>
Cc: Linus Walleij <linux.walleij@linaro.org>
- Fix for the thermal node to be contained in the PRCMU node
- Add the DTS and auxdata needed to boot the U8540 platform
- Various regulators added and renamed
- Rename base SoC node
- A bunch of DMA patches adding channels for DT boots
- A bunch of crypto+hash patches adding config for DT boots
- A bunch of patches fixing the ALSA SoC support to work
- Register the LP5521 LEDs
- Fix a number of typos and naming errors
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)
iQIcBAABAgAGBQJRrcq+AAoJEEEQszewGV1zRiYP/RaP2Cn78mgvJcjh4Rqw1KmP
LVAyMrmNLtaOKUdSsYfvd+UhIQDF0iDcpS5xRc24w8ZFxVl1Ts8lZ67Jg1r1k1ct
0f0X5o7sZ5YtYMFaJtKIGTqjPaKbSzf2lSEvx0YrzRdNyRNux+sU2tdx1TFPyTvd
OnWH0wPVaPwCVcqc404FaLpH3wFRlGvfGuRV7qT5ACBrMfCRKkQfqdpcLsaJ8cVW
op6kljkaRc56zwnm19LrUTo6h+WYS5DL7VpUSsZ4KsMfgy8RqgkGE9JWjBFp62To
p0HrCwO1lA+JULsI7SW6dRLt+/W+hjsr38B/+/LXZKm4oQo8gE328+l+0+x7NT+3
0tpD4Mw0MCh12ARAb/EEKdomzTZThJk0nJZGUW/EhcmMXw9nLZR9TFy11H0FkVdw
lUukvMAhM/gkGRyYqgMOQdoeC3a3au1O50XEZvYVHQVkXcmQhoY3ckrIWW+BgKQQ
u4wmMcB6Q/bDONqAb5RcFICapSlIrm8KbY9fO0801r5aSDVDxHLblcKF+/J1qcd9
gM68DoJ0A07dJaeHjM9LGdekUiEB6xsI3nU5r0QlNSbkQZqBLiu6PJZXJe8vIPIi
Fo8n3gRfpG97pn3EAaO1aw3w2WX10JEWIYetkwrirJaJiYwB2a2PYVwXLX0zgcZp
B//Uy9xFT3R9Mgv7Cu20
=cph0
-----END PGP SIGNATURE-----
Merge tag 'ux500-dt-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into next/dt
From Linus Walleij:
Device tree patches for ux500, basically trees and auxdata:
- Fix for the thermal node to be contained in the PRCMU node
- Add the DTS and auxdata needed to boot the U8540 platform
- Various regulators added and renamed
- Rename base SoC node
- A bunch of DMA patches adding channels for DT boots
- A bunch of crypto+hash patches adding config for DT boots
- A bunch of patches fixing the ALSA SoC support to work
- Register the LP5521 LEDs
- Fix a number of typos and naming errors
* tag 'ux500-dt-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson: (39 commits)
ARM: ux500: drop any 0x prefix from I2C DT devices
ARM: ux500: Allocate correct amount of memory for the u8540 in DT
ARM: ux500: Provide auxdata to ux500 ASoC driver
ARM: ux500: Add DT regulators for ab8500-codec
ARM: ux500: Correct anamic2 typo in DT files
ARM: ux500: Fix trivial typo in v-anamic1 comment
ARM: ux500: Reduce PRCMU reg-names to shorter form for u8540 DT
ARM: ux500: Add an auxdata entry for MUSB for clock-name look-up
ARM: ux500: cut chip-select GPIOs from SSP device
ARM: ux500: use symbolic names for interrupt flags
ARM: ux500: use #include syntax to include *.dtsi.
ARM: ux500: bump MMC/SD max frequency for DT boots
ARM: ux500: Apply other compatible name to the u8540 DTS file
pinctrl/nomadik: Standardise Pinctrl compat string for DBx5x based platforms
ARM: ux500: Standardise Pinctrl compatible string for DBx5x based platforms
ARM: ux500: Standardise DBx5x0 based Pinctrl compat string in the DTS
crypto: ux500/hash - Enable DT probing of the driver
crypto: ux500/cryp - Enable DT probing of the driver
ARM: ux500: enable the crypto and hash on all dbx500
ARM: ux500: Provide an AUXDATA entry for ux500-hash
...
Signed-off-by: Olof Johansson <olof@lixom.net>
support for the DMA40. Now with MUSB and some platform
data removal.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)
iQIcBAABAgAGBQJRrctTAAoJEEEQszewGV1zoFkP/0ZS3Hw4sGX4CRcVZysFZXon
tEWMtNq3WvugmAMos1BJtVYjbu9oaI0kPnTZOU83rF8YzEGvRUy+3AlZXwGmkyYq
NgdfDElAY815F9pJ3ffFL74Dd36paWPtO55JuUEsdxLZE7c4/qOBHykURU0NzMtK
at70fgVLaNo+mjB+Q2M1ouI5tBCrdwso+vI9SHYlof2wt8TiAmbBTOcKO35nUzlk
brcrTeTtdWCc2foP7cFgmjrsct3CzB4Dfl49MiCv1zsiQL5a+qB0EAMd4xYyuVqb
GE1WQDvDwzEDre0pAb/io/NwnlF81tgr6dhFTeFxB44knqbkptQFw9XCDnTQTy5C
dda5HSJ31ES3N2IUj5K0tlSm3/cBywt5IU79FwhFN4Ndq/nzDtZQ+Y2/X0IA99is
eTpLM+/20juOyTxt4vHhdp4aL4r4ZdmOb0GAsyAg/TtsG5LJhZPIctZ+xexKqAhX
wPkvHubv87ruQC6AOjVXwez+3tzTLuU7H8a9IOHi+oHk4r+mdba3kAKTyEl717Bk
44N0hcSLbZYktE9gdBJWuuySmfLXnbb/lc+2OjFYNWMHIgDbEwS2ZeVnKB8G+Eil
iGDIMMnbCc9vA6fiDARZ3DvLFvahnUbO4BqcFozc/hHbhTceSn9xkXX3NcM8NCWF
EAWWZlx4dtAbzB7ReTDm
=rn7t
-----END PGP SIGNATURE-----
Merge tag 'ux500-dma40-for-arm-soc-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into next/drivers
From Linus Walleij:
Second set of DMA40 changes: refactorings and device tree
support for the DMA40. Now with MUSB and some platform
data removal.
* tag 'ux500-dma40-for-arm-soc-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
dmaengine: ste_dma40: Fetch disabled channels from DT
dmaengine: ste_dma40: Fetch the number of physical channels from DT
ARM: ux500: Stop passing DMA platform data though AUXDATA
dmaengine: ste_dma40: Allow memcpy channels to be configured from DT
dmaengine: ste_dma40_ll: Replace meaningless register set with comment
dmaengine: ste_dma40: Convert data_width from register bit format to value
dmaengine: ste_dma40_ll: Use the BIT macro to replace ugly '(1 << x)'s
ARM: ux500: Remove recently unused stedma40_xfer_dir enums
dmaengine: ste_dma40: Replace ST-E's home-brew DMA direction defs with generic ones
ARM: ux500: Replace ST-E's home-brew DMA direction definition with the generic one
dmaengine: ste_dma40: Use the BIT macro to replace ugly '(1 << x)'s
ARM: ux500: Remove empty function u8500_of_init_devices()
ARM: ux500: Remove ux500-musb platform registation when booting with DT
usb: musb: ux500: add device tree probing support
usb: musb: ux500: attempt to find channels by name before using pdata
usb: musb: ux500: harden checks for platform data
usb: musb: ux500: take the dma_mask from coherent_dma_mask
usb: musb: ux500: move the MUSB HDRC configuration into the driver
usb: musb: ux500: move channel number knowledge into the driver
Align on u8500 version, pass clock base address in clk_init functions
for u8540 and u9540.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Philippe Begnic <philippe.begnic@st.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
phys_addr_t may be 64 bit, which causes this harmless warning
in ux500_read_asicid:
arch/arm/mach-ux500/id.c: In function 'ux500_read_asicid':
arch/arm/include/asm/io.h:159:19: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
#define IOMEM(x) ((void __force __iomem *)(x))
^
arch/arm/mach-ux500/id.c:40:9: note: in expansion of macro 'readl'
return readl(IOMEM(UX500_VIRT_ROM + (addr & 0xfff)));
We can solve this in a nicer way by making UX500_VIRT_ROM have a proper
type to start with and calculating the address using pointer arithmetic.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The DMA platform data is now empty due to some recent refactoring,
so there is no longer a requirement to pass it though.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
STEDMA40_*_TO_* direction definitions are identical in all but name to
the pre-defined generic DMA_*_TO_* ones. Let's make things easy by not
duplicating such things.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As promised, now all devices which resided in u8500_of_init_devices()
have been enabled for Device Tree, we can completely remove it.
Acked-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Now the ux500-musb driver has been enabled for Device Tree, there is no
requirement to register it from platform code.
Acked-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The dma_mask will always be the same as the coherent_dma_mask, so let's
cut down on the platform_data burden and set it as such in the driver.
This also saves us from supporting it separately when we come to enable
this driver for Device Tree.
Cc: linux-usb@vger.kernel.org
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The MUSB HDRC configuration never changes between each of the ux500
supported platforms, so there's little point passing it though platform
data. If we set it in the driver instead, we can make good use of it
when booting with either ATAGs or Device Tree.
Cc: linux-usb@vger.kernel.org
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
For all ux500 based platforms the maximum number of end-points are used.
Move this knowledge into the driver so we can relinquish the burden from
platform data. This also removes quite a bit of complexity from the driver
and will aid us when we come to enable the driver for Device Tree.
Cc: linux-usb@vger.kernel.org
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Ux500 ASoC driver is expected to have a specific device name to get
clock resources correctly. This patch provides the necessary
OF_DEV_AUXDATA to match the name in DT and non-DT cases.
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds pin control tables for the ABx500 (AB8500 and
AB8505) PMIC, which also happens to act as a multimedia
pin expander on the ux500 platforms.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The recently DT:ed MUSB driver will require clock-name by device-name
look-up capability, until common clk has is properly supported by the
ux500 platform.
Acked-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
the ux500 to fetch DMA channels from the device tree:
- Full DT support and channel mapping in the DMA40 driver
- Dropping of platform data for migrated devices on the DT
boot path.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=RTiI
-----END PGP SIGNATURE-----
Merge tag 'ux500-dma40-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into next/drivers
From Linus Walleij:
This is a set of patches from Lee Jones to start converting
the ux500 to fetch DMA channels from the device tree:
- Full DT support and channel mapping in the DMA40 driver
- Dropping of platform data for migrated devices on the DT
boot path.
* tag 'ux500-dma40-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson: (36 commits)
ARM: ux500: Register Cryp and Hash platform drivers on Snowball
crypto: ux500/[cryp|hash] - Show successful start-up in the bootlog
ARM: ux500: Stop passing Cryp DMA channel config information though pdata
crypto: ux500/cryp - Set DMA configuration though dma_slave_config()
crypto: ux500/cryp - Prepare clock before enabling it
ARM: ux500: Stop passing Hash DMA channel config information though pdata
crypto: ux500/hash - Set DMA configuration though dma_slave_config()
crypto: ux500/hash - Prepare clock before enabling it
ARM: ux500: Remove unnecessary attributes from DMA channel request pdata
dmaengine: ste_dma40: Correct copy/paste error
ARM: ux500: Remove DMA address look-up table
dmaengine: ste_dma40: Remove redundant address fetching function
dmaengine: ste_dma40: Only use addresses passed as configuration information
ARM: ux500: Stop passing UART's platform data for Device Tree boots
dmaengine: ste_dma40: Don't configure runtime configurable setup during allocate
dmaengine: ste_dma40: Remove unnecessary call to d40_phy_cfg()
dmaengine: ste_dma40: Separate Logical Global Interrupt Mask (GIM) unmasking
ARM: ux500: Pass remnant platform data though to DMA40 driver
dmaengine: ste_dma40: Supply full Device Tree parsing support
dmaengine: ste_dma40: Allow driver to be probe()able when DT is enabled
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Update MSP1 pinctrl definitions in mop500_family_pinmap by removing
sleep state and setting default ones as pin hogs, as those are used by
both ux500-msp-i2s.1 and ux500-msp-i2s.3.
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch fixes a bug introduced in the v3.10 merge window.
The AB8500 External Regulator driver has recently landed upstream,
which registers each of the 3 external regulators located on the
AB8500. If these regulators are marked as 'always on', there is a
potential for power-loss. If they're not and are seemingly unused
the Regulator subsystem will attempt to disable them to save power.
This causes an issue for AUX1, AUX2 and AUX3 as they obtain their
power from EXT3. So we're specifying that here to prevent EXT3 from
being powered down.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Multiplatform calls all enabled platforms' initcalls. In the
ux500_idle_init() initcall we call into the DBx500-PRCMU which in turn
executes some ux500 specific register reads/writes. When running on
some !ux500 platforms this ends up causing a kernel Oops. This patch
ensures the PRCMU call is only invoked when running on ux500 based
platforms.
Reported-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This provides a device name which is required by the common clk API.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This provides a device name which is required by the common clk API.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
[Edited patch subject]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Olof Johansson