This patch adds Z clock for R8A7795 SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
According to the R-Car Gen3 Hardware Manual Errata for Rev 0.55 of
September 8, 2017, the parent clock of the INTC-AP module clock on R-Car
H3 ES2.0 is S0D3.
This change has no functional impact.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
On some R-Car Gen3 SoCs (e.g. R-Car D3), PLL1 and PLL3 use a divider
value different from one. Extend struct rcar_gen3_cpg_pll_config to handle
this. As all multipliers and dividers are small, table size increase
can be kept limited by storing them in u8s instead of unsigned ints,
which saves ca. 0.5 KiB for a generic kernel.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Cfr. the errata of April 14, 2017, for the R-Car Gen3 Hardware Manual
Rev. 0.53E.
These have no user-visible effect, as the clock frequencies stay the
same.
Fixes: 5573d19412 ("clk: renesas: r8a7795: Add support for R-Car H3 ES2.0")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
The Clock Pulse Generator / Module Standby and Software Reset module in
R-Car H3 ES2.0 differs from ES1.x in the following areas:
- More core clocks (S0D2, S0D3, S0D6, S0D8, S0D12),
- Different parent clocks for AUDMAC, EtherAVB, FCP, FDP, IMR,
SYS-DMAC, VIN, VSPB, VSPI,
- Removal of modules CSI21, FCPCI, FCPF2, FCPVD3, FCPVI2, FDP1-2,
USB3-IF1, VSPD3, VSPI2,
- Addition of modules EHCI3, HS-USB-IF3, USB-DMAC3-0, USB-DMAC3-1.
The goal is twofold:
1. Support both the ES1.x and ES2.0 SoC revisions in a single binary
for now,
2. Make it clear which code supports ES1.x, so it can easily be
identified and removed later, when production SoCs are deemed
ubiquitous.
This is achieved by:
- Updating the clock tables for the latest revision (ES2.0), but not
removing clocks that only exist on earlier revisions (ES1.x),
- Detecting the SoC revision at runtime using the new soc_device_match()
API, and fixing up the clocks tables to match the actual SoC
revision, by:
- NULLifying core and module clocks of modules that do not exist,
- Reparenting module clocks that have a different parent on ES1.x.
Based on R-Car Gen3 Hardware User's Manual rev. 0.53E.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Pass the mode pin states from the SoC-specific CPG/MSSR driver to the
R-Car Gen3 CPG driver core, as their state will be needed to make some
core clock configuration decisions.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The parent clock of the Audio DMACs is the "ZS" AXI bus clock, which
maps to S3D1 on R-Car H3 ES1.x.
All module clocks must be sorted by clock ID.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Add the IMR[0-3] clocks to the R8A7795 CPG/MSSR driver.
Based on the original (and large) patch by Konstantin Kozhevnikov
<Konstantin.Kozhevnikov@cogentembedded.com>.
Signed-off-by: Konstantin Kozhevnikov <Konstantin.Kozhevnikov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Correct HDMI parent clock so that the rate of the
HDMI clock is 1/4 rather than 1/2 of the rate of PLL1
as per the v0.52 (Jun, 15) manual.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Obtain the values of the mode pins from the R-Car RST driver, which
relies on the presence in DT of a device node for the RST module.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
According to the datasheet, SDn clocks are from the SDSRC clock. And
the SDSRC has a 1/2 divider. So, we should have ".sdsrc" as an internal
core clock. Otherwise, since the sdhi driver will calculate clock for
a sd card using the wrong parent clock rate, and then performance will
be not good.
Fixes: 90c073e539 ("clk: shmobile: r8a7795: Add SD divider support")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: stable@vger.kernel.org
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
According to the latest information, the parent clock of the LVDS module
clock is the S0D4 clock, not the S2D1 clock.
Note that this change has no influence on actual operation, as the
rcar-du LVDS encoder driver doesn't use the parent clock's rate.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Extract the code to support parts common to all members of the R-Car
Gen3 SoC family into a separate file, to ease sharing among SoC-specific
drivers.
Note that while the cpg_pll_configs[] arrays and the selection of the
config based on the MODE bits are identical on R-Car H3 and R-Car M3-W,
they are not common, and may be different on other R-Car Gen3 SoCs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Simon Horman <horms+renesas@verge.net.au>
R can select between two parents. We deal with it like this: During
initialization, check if EXTALR is populated. If so, use it for R. If
not, use R_Internal. clk_mux doesn't help here because we don't want to
switch parents depending on the clock rate. The clock rate (and source)
should stay constant for the watchdog, so I think a setup like this
during initialization makes sense.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
About SD clocks: The clock type is Gen3 specific, the callbacks are all
Gen3 specific; I think the clock definition should also be Gen3 specific
and not in the general header file.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This is part of an ongoing process to migrate from ARCH_SHMOBILE to
ARCH_RENESAS the motivation for which being that RENESAS seems to be a more
appropriate name than SHMOBILE for the majority of Renesas ARM based SoCs.
Along with the above mentioned Kconfig changes it seems appropriate
to also rename directories that only hold drivers for such SoCs.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Takeshi Kihara