The V4L2 sub-device API does not support the crop default target. A number
of drivers apparently still did support this, likely as it was needed by
the SoC camera framework. Drop support for the default crop rectaingle in
sub-device drivers, and use the bounds rectangle in SoC camera instead.
Reported-by: Helmut Grohne <h.grohne@intenta.de>
Suggested-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
A number of sub-device drivers used a static name for the sub-device, and
thus the media entity. As the entity name must be unique within a media
device, this makes it impossible to have more than one instance of each
device in a media device. This is a rather severe limitation.
Instead of fixing these drivers, add a comment to the drivers noting that
such static names may not be used in the future.
The alternative of fixing the drivers is troublesome as the entity (as
well as sub-device) name is part of the uAPI. Changing that is almost
certain to break something. As these devices are old but no-one has
encountered a problem with the static names, leave it as-is.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The event subscriptions are added to the subscribed event list while
holding a spinlock, but that lock is subsequently released while still
accessing the subscription object. This makes it possible to unsubscribe
the event --- and freeing the subscription object's memory --- while
the subscription object is simultaneously accessed.
Prevent this by adding a mutex to serialise the event subscription and
unsubscription. This also gives a guarantee to the callback ops that the
add op has returned before the del op is called.
This change also results in making the elems field less special:
subscriptions are only added to the event list once they are fully
initialised.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: stable@vger.kernel.org # for 4.14 and up
Fixes: c3b5b0241f ("V4L/DVB: V4L: Events: Add backend")
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This introduces support for the Sunxi tiled NV12 format, where each
component of the YUV frame is divided into macroblocks. Hence, the size
of each plane requires specific alignment. The pixels inside each
macroblock are coded in linear order (line after line from top to
bottom).
This tiled NV12 format is used by the video engine on Allwinner
platforms: it is the default format for decoded frames (and the only
one available in the oldest supported platforms).
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Stateless video decoding engines require both the MPEG-2 slices and
associated metadata from the video stream in order to decode frames.
This introduces definitions for a new pixel format, describing buffers
with MPEG-2 slice data, as well as control structure sfor passing the
frame metadata to drivers.
This is based on work from both Florent Revest and Hugues Fruchet.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The helper indicating whether buffers are associated with the request is
reworked and renamed to return the number of associated buffer objects.
This is useful for drivers that need to check how many buffers are in
the request to validate it.
Existing users of the helper don't need particular adaptation since the
meaning of zero/non-zero remains consistent.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Fix this sparse warning:
drivers/media/v4l2-core/v4l2-compat-ioctl32.c:256: warning:
Function parameter or member 'capabilities' not described in 'v4l2_create_buffers32'
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Clang warns when one enumerated type is implicitly converted to another.
drivers/media/platform/davinci/vpbe_display.c:524:24: warning: implicit
conversion from enumeration type 'enum osd_v_exp_ratio' to different
enumeration type 'enum osd_h_exp_ratio' [-Wenum-conversion]
layer_info->h_exp = V_EXP_6_OVER_5;
~ ^~~~~~~~~~~~~~
1 warning generated.
This appears to be a copy and paste error judging from the couple of
lines directly above this statement and the way that height is handled
in the if block above this one.
Reported-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Clang warns when a variable is assigned to itself.
drivers/media/pci/bt8xx/bttv-driver.c:2043:13: warning: explicitly
assigning value of variable of type '__s32' (aka 'int') to itself
[-Wself-assign]
min_height = min_height;
~~~~~~~~~~ ^ ~~~~~~~~~~
1 warning generated.
There doesn't appear to be any good reason for this and this statement
was added in commit e5bd0260e7 ("V4L/DVB (5077): Bttv cropping
support") back in 2007. Just remove it.
Reported-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
altera_hw_filt_init() which calls append_internal() assumes
that the node was successfully linked in while in fact it can
silently fail. So the call-site needs to set return to -ENOMEM
on append_internal() returning NULL and exit through the err path.
Fixes: 349bcf02e3 ("[media] Altera FPGA based CI driver module")
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Return statements in functions returning bool should use true or false
instead of an integer value.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
On a decoder instance, after the profile has been parsed from the stream
__v4l2_ctrl_s_ctrl() is called to notify userspace about changes in the
read-only profile control. This ends up calling back into the CODA driver
where a missing check on the s_ctrl caused the profile information that has
just been parsed from the stream to be overwritten with the default
baseline profile.
Later on the driver fails to enable frame reordering, based on the wrong
profile information.
Fixes: 347de126d1da (media: coda: add read-only h.264 decoder
profile/level controls)
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Warn and return error from the reqbufs ioctl when driver sets 0 number
of planes or 0 as plane sizes, as these values don't make any sense.
Checking this here stops obviously wrong values from propagating
further and causing various problems that are hard to trace back to
either of these values being 0.
Signed-off-by: Johan Fjeldtvedt <johfjeld@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
of_node_put has taken the null pinter check into account. So it is
safe to remove the duplicated check before of_node_put.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
of_node_put has taken the null pointer check into account. So it is
safe to remove the duplicated check before of_node_put.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
These names have been renamed in the CTA-861 standard due to trademark
issues. Replace them here as well so they are in sync with the standard.
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Cc: stable@vger.kernel.org
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The CTA-861 standards have been updated to refer to opRGB instead
of AdobeRGB. The official standard is in fact named opRGB, so
switch to that.
The two old defines referring to ADOBERGB in the public API are
put under #ifndef __KERNEL__ and a comment mentions that they are
deprecated.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: stable@vger.kernel.org
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Include the missing interrupt.h header to fix compilation on i386 or
x86_64:
../drivers/media/platform/imx-pxp.c:988:1: error: unknown type name 'irqreturn_t'
static irqreturn_t pxp_irq_handler(int irq, void *dev_id)
^
../drivers/media/platform/imx-pxp.c: In function 'pxp_irq_handler':
../drivers/media/platform/imx-pxp.c:1012:9: error: 'IRQ_HANDLED' undeclared (first use in this function)
return IRQ_HANDLED;
^
../drivers/media/platform/imx-pxp.c:1012:9: note: each undeclared identifier is reported only once for each function it appears in
../drivers/media/platform/imx-pxp.c: In function 'pxp_probe':
../drivers/media/platform/imx-pxp.c:1660:2: error: implicit declaration of function 'devm_request_threaded_irq' [-Werror=implicit-function-declaration]
ret = devm_request_threaded_irq(&pdev->dev, irq, NULL, pxp_irq_handler,
^
../drivers/media/platform/imx-pxp.c:1661:4: error: 'IRQF_ONESHOT' undeclared (first use in this function)
IRQF_ONESHOT, dev_name(&pdev->dev), dev);
Fixes: 51abcf7fdb ("media: imx-pxp: add i.MX Pixel Pipeline driver")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The vicodec does not use the aborting field. In fact, this driver
can't really cancel any work, since it performs all the work
in device_run().
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The vicodec doesn't use the Subdev API, so drop the dependency.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
state->info was NULL since I completely forgot to set state->info.
Oops.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reported-by: Ezequiel Garcia <ezequiel@collabora.com>
Tested-by: Ezequiel Garcia <ezequiel@collabora.com>
[hans.verkuil@cisco.com: re-add q_out which was removed by commit 703fe34bac]
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
These functions did not return an error if state->info was NULL
or an unsupported pixelformat was selected (should not happen,
but just to be on the safe side).
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The saa7134 Tiger board has a front panel connector at the back (labeled
panel 2 on the PCB), with S-VIDEO, composite and audio.
This patch adds those inputs.
Signed-off-by: Alexandre GRIVEAUX <agriveaux@deutnet.info>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The driver may sleep in a interrupt handler.
The function call paths (from bottom to top) in Linux-4.16 are:
[FUNC] kzalloc(GFP_KERNEL)
drivers/media/pci/ivtv/ivtv-yuv.c, 938:
kzalloc in ivtv_yuv_init
drivers/media/pci/ivtv/ivtv-yuv.c, 960:
ivtv_yuv_init in ivtv_yuv_next_free
drivers/media/pci/ivtv/ivtv-yuv.c, 1126:
ivtv_yuv_next_free in ivtv_yuv_setup_stream_frame
drivers/media/pci/ivtv/ivtv-irq.c, 827:
ivtv_yuv_setup_stream_frame in ivtv_irq_dec_data_req
drivers/media/pci/ivtv/ivtv-irq.c, 1013:
ivtv_irq_dec_data_req in ivtv_irq_handler
To fix this bug, GFP_KERNEL is replaced with GFP_ATOMIC.
This bug is found by my static analysis tool DSAC.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Move cec_get_edid_phys_addr() to cec-adap.c. It's not worth keeping
a separate source for this.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: <stable@vger.kernel.org> # for v4.17 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Several CEC functions are actually specific for use with receivers,
i.e. they should be part of the V4L2 subsystem, not CEC.
These functions deal with validating and modifying EDIDs for (HDMI)
receivers, and they do not actually have anything to do with the CEC
subsystem and whether or not CEC is enabled. The problem was that if
the CEC_CORE config option was not set, then these functions would
become stubs, but that's not right: they should always be valid.
So replace the cec_ prefix by v4l2_ and move them to v4l2-dv-timings.c.
Update all drivers that call these accordingly.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reported-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: <stable@vger.kernel.org> # for v4.17 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The cec_phys_addr_validate() function will be moved to V4L2,
so use a simplified variant of that function in cec-api.c.
cec now no longer calls cec_phys_addr_validate() and it can
be safely moved to V4L2.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: <stable@vger.kernel.org> # for v4.17 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This function is needed by both V4L2 and CEC, so move this to
cec.h as a static inline since there are no obvious shared
modules between the two subsystems.
This patch, together with the following ones, fixes a
dependency bug: if CEC_CORE is disabled, then building adv7604
(and other HDMI receivers) will fail because an essential
function is now stubbed out.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: <stable@vger.kernel.org> # for v4.17 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Mode setting depends on last mode set, in particular
because of exposure calculation when downscale mode
change between subsampling and scaling.
At stream on the last mode was wrongly set to current mode,
so no change was detected and exposure calculation
was not made, fix this.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Tested-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
When switching from auto to manual mode, V4L2 core is calling
g_volatile_ctrl() in manual mode in order to get the manual initial value.
Remove the manual mode check/return to not break this behaviour.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Tested-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
ov5640_set_mode_exposure_calc() is checking binning value but
binning value read is buggy, fix this.
Rename ov5640_binning_on() to ov5640_get_binning() as per other
similar functions.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Ensure that auto gain and auto exposure are well restored
when changing mode.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Tested-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Symptom was black image when capturing HD or 5Mp picture
due to manual exposure set to 1 while it was intended to
set autoexposure to "manual", fix this.
Fixes: bf4a4b518c ("media: ov5640: Don't force the auto exposure state at start time").
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
As of: commit 476dec012f ("media: ov5640: Add horizontal and vertical
totals") the timings parameters gets programmed separately from the
static register values array.
When changing capture mode, the vertical and horizontal totals gets
inspected by the set_mode_exposure_calc() functions, and only later
programmed with the new values. This means exposure, light banding
filter and shutter gain are calculated using the previous timings, and
are thus not correct.
Fix this by programming timings right after the static register value
table has been sent to the sensor in the ov5640_load_regs() function.
Fixes: 476dec012f ("media: ov5640: Add horizontal and vertical totals")
Tested-by: Steve Longerbeam <slongerbeam@gmail.com> # i.MX6q SabreSD, CSI-2
Tested-by: Loic Poulain <loic.poulain@linaro.org> # Dragonboard-410c, CSI-2
Signed-off-by: Samuel Bobrowicz <sam@elite-embedded.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Rework the MIPI interface startup sequence with the following changes:
- Remove MIPI bus initialization from the initial settings blob
- At set_power(1) time power up MIPI Tx/Rx and set data and clock lanes in
LP11 during 'sleep' and 'idle' with MIPI clock in non-continuous mode.
- At s_stream time enable/disable the MIPI interface output.
- Restore default settings at set_power(0) time.
Before this commit the sensor MIPI interface was initialized with settings
that require a start/stop sequence at power-up time in order to force lanes
into LP11 state, as they were initialized in LP00 when in 'sleep mode',
which is assumed to be the sensor manual definition for the D-PHY defined
stop mode.
The stream start/stop was performed by enabling disabling clock gating,
and had the side effect to change the lanes sleep mode configuration when
stream was stopped.
Clock gating/ungating:
- ret = ov5640_mod_reg(sensor, OV5640_REG_MIPI_CTRL00, BIT(5),
- on ? 0 : BIT(5));
- if (ret)
Set lanes in LP11 when in 'sleep mode':
- ret = ov5640_write_reg(sensor, OV5640_REG_PAD_OUTPUT00,
- on ? 0x00 : 0x70);
This commit fixes an issue reported by Jagan Teki on i.MX6 platforms that
prevents the host interface from powering up correctly:
https://lkml.org/lkml/2018/6/1/38
It also improves MIPI capture operations stability on my testing platform
where MIPI capture often failed and returned all-purple frames.
Fixes: f22996db44 ("media: ov5640: add support of DVP parallel interface")
Tested-by: Steve Longerbeam <slongerbeam@gmail.com> (i.MX6q SabreSD, CSI-2)
Tested-by: Loic Poulain <loic.poulain@linaro.org> (Dragonboard-410c, CSI-2)
Reported-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The function not only does initialization but also registers the subdevice
so change its name to make this more clear.
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The driver registers the v4l2 subdevice before attempting to power on the
chip and checking its ID. This means that a media device driver that it's
waiting for this subdevice to be bound, will prematurely expose its media
device node to userspace because if something goes wrong the media entity
will be cleaned up again on the ov2680 probe function.
This also simplifies the probe function error path since no initialization
is made before attempting to enable the resources or checking the chip ID.
Fixes: 3ee47cad3e ("media: ov2680: Add Omnivision OV2680 sensor driver")
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This code doesn't check for NULL consistently and it generates a Smatch
warning:
drivers/media/i2c/sr030pc30.c:575 sr030pc30_base_config()
error: we previously assumed 'info->pdata' could be null (see line 572)
Fortunately, "info->pdata" can't be NULL to that check can be removed.
The other thing is that if "ret" is an error code here, then we don't
want to do the next call to cam_i2c_write(), so actually let's flip that
test around and return the error. This is more of a theoretical issue
than something which is likely to affect real life.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The sub-device name is set right after in v4l2_i2c_subdev_init(). Remove
the redundant strcpy() call.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Use v4l2_i2c_subdev_set_name() to set the name of the smiapp driver's
sub-devices. There is no functional change.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
v4l2_i2c_subdev_set_name() can be used to assign a name to a sub-device.
This way uniform names can be formed easily without having to resort to
things such as snprintf in drivers.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Currently 2-bytes and 3-bytes registers are read one byte at a time,
doing the needed shift & mask each time.
Replace all of this code by a unique helper function that calls
regmap_bulk_read(), which has two advantages:
- reads all the bytes in a unique I2C transaction
- simplifies code to read multibyte registers
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This parameter holds the number of bytes, not bits.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
A mix of "mode", "format" and "frmfmt" is used to refer to the sensor
readout mode. Use the term "mode" for all of them. Now "format" is
only used in the V4L2 meaning.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Forcibly setting the subdev name to DRIVER_NAME (i.e. "IMX274") makes
it non-unique and less informative.
Let the driver use the default name from i2c, e.g. "IMX274 2-001a".
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Rearrange the imx274_start_<N> register tables to better match the
datasheet and slightly simplify code:
- collapes tables 1 and 2, they are applied one after each other and
together they implement the fixed part 1 of the startup procedure
in the datasheet
- while there, cleanup comments
- rename tables 3 and 4 -> 2 and 3, coherently with the datasheet
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The "mode" has been renamed to "binning" in commit 39dd23dc9d
("media: imx274: add cropping support via SELECTION API"), but this
define has not been updated.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The device is already suspended when it's the driver's remove function is
called. Remove redundant pm_runtime_set_suspended call.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The UDS is currently restricted based on a partition size of 256 pixels.
Document the actual restrictions, but don't increase the implementation.
The extended partition algorithm may later choose to utilise a larger
partition size to support overlapping partitions which will improve the
quality of the output images.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The SRU is currently restricted to 256 pixels as part of the current
partition algorithm. Document that the actual capability of this
component is 288 pixels, but don't increase the implementation.
The extended partition algorithm may later choose to utilise a larger
input to support overlapping partitions which will improve the quality
of the output images.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The style of this driver uses periods at the end of sentences in
comments, but it is applied inconsitently.
Update a selection of comments which were discovered to be missing their
period. Also fix the spelling of one usage of 'instantiate'
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The VSP1 has a minimum width and height of a single pixel, with the
exception of pixel formats with sub-sampling.
Remove the artificial minimum width and minimum height limitation, and
instead clamp the minimum dimensions based upon the sub-sampling
parameter of that dimension.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
YCbCr planar formats can have different pitch values for the luma and
chroma planes. This isn't taken into account in the driver. Fix it.
Based on a BSP patch from Koji Matsuoka <koji.matsuoka.xm@renesas.com>.
Fixes: 7863ac504b ("drm: rcar-du: Add tri-planar memory formats support")
[Updated documentation of the struct vsp1_du_atomic_config pitch field]
Signed-off-by: Koji Matsuoka <koji.matsuoka.xm@renesas.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The LIF module has a data buffer to accommodate clock rate differences
between the DU and the VSP. Several programmable threshold values
control DU start of frame notification by the VSP and VSP clock
stop/resume. The R-Car Gen2 and Gen3 datasheets recommend values for the
different SoCs. Update the driver to use the recommended values for
optimal operation.
Based on a BSP patch from Koji Matsuoka <koji.matsuoka.xm@renesas.com>,
with Gen2 and V3H/V3M updates.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
All source files of the vsp1 driver are licensed under the GPLv2+ except
for vsp1_regs.h which is licensed under GPLv2. This is caused by a bad
copy&paste that dates back from the initial version of the driver. Fix
it.
Acked-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Acked-by: Sergei Shtylyov<sergei.shtylyov@cogentembedded.com>
Acked-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Fix build when MFD_CROS_EC is not enabled but COMPILE_TEST=y.
Fixes this build error:
ERROR: "cros_ec_cmd_xfer_status" [drivers/media/platform/cros-ec-cec/cros-ec-cec.ko] undefined!
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The recent tvp5150 patchset added two new warnings:
drivers/media/i2c/tvp5150.c: In function 'tvp5150_querystd':
drivers/media/i2c/tvp5150.c:829:18: warning: unused variable 'decoder' [-Wunused-variable]
struct tvp5150 *decoder = to_tvp5150(sd);
^~~~~~~
drivers/media/i2c/tvp5150.c:1522:6: warning: no previous prototype for 'tvp5150_volatile_reg' [-Wmissing-prototypes]
bool tvp5150_volatile_reg(struct device *dev, unsigned int reg)
^~~~~~~~~~~~~~~~~~~~
Get rid of them.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
When irq is used, the lock is set via IRQ code. When it isn't,
the driver just assumes it is always locked. Instead, read the
lock status from the status register.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add the querystd video_op and make it return V4L2_STD_UNKNOWN while the
TVP5150 is not locked to a signal.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add callback to retrieve the current set norm.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Issue a V4L2_EVENT_SOURCE_CHANGE notification when the TVP5150 locks
onto a signal and when it loses the lock.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
[m.felsch@pengutronix.de: partly mainline part port]
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
To avoid short frames on stream start, keep output pins at high impedance
while we are not properly locked onto the input signal.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This patch adds an optional interrupt handler to handle the sync
lock interrupt and sync lock status.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
[m.felsch@pengutronix.de: move added .g_std callback to separate patch]
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
To allow optional interrupt support, we want to configure the pin settings
dynamically. Move those register accesses out of the static initialization
tables.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
[m.felsch@pengutronix.de: drop init_default register remove]
[m.felsch@pengutronix.de: fix regmap access during reset()]
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
To trigger standard autodetection only the reset part of the routine
is necessary during probe(). Split this out to make it callable on its own.
[m.felsch@pengutronix.de: adapt commit message]
[m.felsch@pengutronix.de: add tvp5150_enable() to tvp5150_s_stream()]
[m.chehab@samsung.com: fix a compilation breakage]
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Make sure to not overwrite decoder->norm when setting the standard
in hardware, but only when instructed by V4L2 API calls.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If cropping isn't set explicitly by userspace, reset it to the maximum
possible rectangle in subdevice open if a standard change is detected.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
[m.felsch@pengutronix.de: move code from internal_ops.open() to pad_ops.init_cfg()]
[m.felsch@pengutronix.de: make use of tvp5150_set_default() helper]
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The patch adds three macros to bundle the mbus_framefmt default
values and a helper function to set the the default crop and
mbus_framefmt values.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Since commit 9a4c7e68f7e0 ("media: tvp5150: convert register
access to regmap")' the driver supports regmap. Now we can drop
the handmade bit update sequence and move to the regmap provided
helpers.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Regmap provides built in debugging, caching and provides dedicated
accessors for bit manipulations in registers, which make the following
changes a lot simpler.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The function only consists of a single switch case block without a
default case. Unsupported control requests are indicated by the -EINVAL
return code trough the last return statement at the end of the function. So
exiting just the switch case block returns the -EINVAL error code but the
hue control is supported and a zero should be returned instead.
Replace the break by a 'return 0' to fix this behaviour.
Fixes: d183e4efca ("[media] v4l: tvp5150: Add missing break in set
control handler")
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The driver ignored the width alignment which exists due to the UYVY
colorspace format. Fix the width alignment and make use of the the
provided v4l2 helper function to set the width, height and all
alignments in one.
Fixes: 963ddc63e2 ("[media] media: tvp5150: Add cropping support")
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Now that all drivers are using pad signal types, we can get
rid of the global static definition, as routes are stablished
using the pad signal type.
The tuner and IF-PLL pads are now used only by the tuner core,
so move the definitions to be there.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
As we don't need anymore to share pad numbers with similar
drivers, use its own pad definition instead of a global
model.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
As we don't need anymore to share pad numbers with similar
drivers, use its own pad definition instead of a global
model.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
As we don't need anymore to share pad numbers with similar
drivers, use its own pad definition instead of a global
model.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
As we don't need anymore to share pad numbers with similar
drivers, use its own pad definition instead of a global
model.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
As we don't need anymore to share pad numbers with similar
drivers, use its own pad definition instead of a global
model.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
As we don't need anymore to share pad numbers with similar
drivers, use its own pad definition instead of a global
model.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
As we don't need anymore to share pad numbers with similar
drivers, use its own pad definition instead of a global
model.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
When creating the audio link, use pad signals, instead of
hardcoding using the pad index number.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
On tuner pads, multiple signals are present. Be sure to get
the right PAD by using them.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
It is not trivial to debug troubles at media graph build.
So, add print messages to help debug what's happening,
in the case of an error occurs.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Instead of relying on a static map for pids, use the new sig_type
"taint" type to setup the pipelines with the same tipe between
different entities.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Consumer devices are provided with a wide different range of types
supported by the same driver, allowing different configutations.
In order to make easier to setup media controller links, "taint"
pads with the signal type it carries.
While here, get rid of DEMOD_PAD_VBI_OUT, as the signal it carries
is actually the same as the normal video output.
The difference happens at the video/VBI interface:
- for VBI, only the hidden lines are streamed;
- for video, the stream is usually cropped to hide the
vbi lines.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The signal there is the same as the video output (well,
except for sliced VBI, but let's simplify the model and ignore
it, at least for now - as it is routed together with raw
VBI).
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The v4l2-compliance tool complains if a video doesn't start
with a zero sequence number.
While this shouldn't cause any real problem for apps, let's
make it happier, in order to better check the v4l2-compliance
differences before and after patchsets.
This is actually an old issue. It is there since at least its
videobuf2 conversion, e. g. changeset 3829fadc461 ("[media]
em28xx: convert to videobuf2"), if VB1 wouldn't suffer from
the same issue.
Cc: stable@vger.kernel.org
Fixes: d3829fadc4 ("[media] em28xx: convert to videobuf2")
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Instead of using a register value, use an AMUX name, as otherwise
VIDIOC_G_AUDIO would fail.
Cc: stable@vger.kernel.org
Fixes: 766ed64de5 ("V4L/DVB (11827): Add support for Terratec Grabster AV350")
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Follow the V4L2 spec, as warned by v4l2-compliance:
warn: v4l2-test-formats.cpp(732): TRY_FMT cannot handle an invalid pixelformat.
warn: v4l2-test-formats.cpp(733): This may or may not be a problem. For more information see:
warn: v4l2-test-formats.cpp(734): http://www.mail-archive.com/linux-media@vger.kernel.org/msg56550.html
Cc: stable@vger.kernel.org
Fixes: bddcf63313 ("V4L/DVB (9927): em28xx: use a more standard way to specify video formats")
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The a->index is not the name of the internal amux entry,
but, instead a value from zero to the maximum number
of audio inputs.
As the actual available inputs depend on each board, build
it dynamically.
This is broken for a really long time. On a quick check,
since at least commit 195a4ef627 ("V4L/DVB (6585): Convert
em28xx to video_ioctl2") this was not implemented right.
Fixes: 195a4ef627 ("V4L/DVB (6585): Convert em28xx to video_ioctl2")
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Replace "falltrough" with a proper "fall through" annotation.
This fix is part of the ongoing efforts to enabling
-Wimplicit-fallthrough
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In preparation to remove the node name pointer from struct device_node,
convert printf users to use the %pOFn format specifier.
Cc: "Lad, Prabhakar" <prabhakar.csengg@gmail.com>
Cc: Benoit Parrot <bparrot@ti.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Hyun Kwon <hyun.kwon@xilinx.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The VIDEO_STILLPICTURE is only implemented by one driver, while
VIDEO_GET_EVENT has two users in tree. In both cases, it is fairly
easy to handle the compat ioctls in the native handler rather
than relying on translation in fs/compat_ioctls.
In effect, this means that now the drivers implement both structure
layouts in both native and compat mode, but I don't see anything
wrong with that.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Most DVB audio and video ioctl commands are completely compatible,
and are implemented by just two drivers: ttpci and ivtv. In both
cases, we can use the same ioctl handler for both native and
compat ioctl handling, and remove the entries from the global
lookup table.
In case of ttpci, this directly hooks into the file_operations
structure, and for ivtv, we have to set the compat_ioctl32
method in v4l2_file_operations. For all I can tell, setting it
to video_ioctl2 will still do the right thing for all commands.
Note that for the VIDEO_STILLPICTURE and VIDEO_GET_EVENT commands,
a translation handler in fs/compat_ioctl.c is still used. This
works because the command numbers are different on 32-bit
systems.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
All the CEC ioctls are compatible, and they are only implemented
in one driver, so we can simply let this driver handle them
natively.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
All dmx ioctls are compatible, and they are only implemented
in one file, so we can replace the list of commands in
fs/compat_ioctl.c with a single line in dmxdev.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
dma_zalloc_coherent has implemented the dma_alloc_coherent() + memset(),
We prefer to dma_zalloc_coherent instead of open-codeing.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Motion eye video4linux driver for Sony Vaio PictureBook desn't validate user-controlled parameter
'vma->vm_pgoff', a malicious process might access all of kernel memory from user space by trying
pass different arbitrary address.
Discussion: http://www.openwall.com/lists/oss-security/2018/07/06/1
Signed-off-by: Lao Wei <zrlw@qq.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
As original license mentioned, it is GPL-2.0+ in SPDX.
Then, MODULE_LICENSE() should be "GPL" instead of "GPL v2".
See ${LINUX}/include/linux/module.h
"GPL" [GNU Public License v2 or later]
"GPL v2" [GNU Public License v2]
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
While v4l2_i2c_subdev_init does give a unique name to the subdev, matching
the one appearing in dmesg for messages generated by dev_info and friends
(e.g. imx185 30-0010), v4l2_spi_subdev_init does a poor job, copying only
the driver name, but not the dev_name(), yielding e.g. "imx185", but
missing the "spi1.1" part, and not generating a unique name.
Fix that.
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The check for irq_mode == 2 occurs is always false and hence flags
is always zero. This is because the check occurs in a path where
irq_mode is >= 3. Clean up the code by removing the check and irq_mode
and just pass 0.
Detected by CoverityScan, CID#1472214 ("Logically dead code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Cc: Ralph Metzler <rjkm@metzlerbros.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
As pointed by Daniel Scheller <d.scheller@gmx.net>, sparse
warns that a segment may fall through. We're deprecating
this warning in favor of gcc 8 equivalent warning.
In this specific case, the code for DVB-S applies for DVB-S2.
In a matter of fact, several things there (like rolloff
factor logic) assume that the transponder is DVB-S2.
So, add the corresponding fall-trough markup, for gcc to
properly ignore it.
Reported-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Time "in interrupt" accounting with the help of `jiffies' is a pointless
exercise. This variable isn't even used.
Remove time_in_irq.
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The context in which sd_dq_callback() is non atomic, there is even
msleep() at the end of the function. There is no need to use GFP_ATOMIC
here - use GFP_KERNEL instead.
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
As far as I can tell em28xx_audio_urb_init() is called once during
initialization from non atomic context. Memory allocation from
non atomic context should use GFP_KERNEL to avoid using emergency pool
for memory allocation.
Use GFP_KERNEL for memory allocation.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
As both the MODULE_LICENSE and the boilerplates are now in sync and clear
that the driver is licensed under the terms of the GPLv2-only, add a
matching SPDX license identifier tag.
Cc: Ralph Metzler <rjkm@metzlerbros.de>
Cc: Manfred Voelkel <mvoelkel@DigitalDevices.de>
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In commit 3db30defab4b ("use correct MODULE_LINCESE for GPL v2 only
according to notice in header") in the upstream repository for the
mentioned driver at https://github.com/DigitalDevices/dddvb.git, the
MODULE_LICENSE was fixed to "GPL v2" and is now in sync with the GPL
copyright boilerplate. Apply this change to the kernel tree driver
as well.
Cc: Ralph Metzler <rjkm@metzlerbros.de>
Cc: Manfred Voelkel <mvoelkel@DigitalDevices.de>
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
As it is clear that the driver is licensed under the terms of GPLv2-only
by now, add a matching SPDX license identifier to all driver files.
Cc: Ralph Metzler <rjkm@metzlerbros.de>
Cc: Manfred Voelkel <mvoelkel@DigitalDevices.de>
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The stv6111.h doesn't carry any header nor any licensing boilerplate at
all, so copy this from the main driver file stv6111.c.
[mchehab@kernel.org: kept only the part of this patch that copied
the license from stv6111.c into stv6111.h]
Cc: Ralph Metzler <rjkm@metzlerbros.de>
Cc: Manfred Voelkel <mvoelkel@DigitalDevices.de>
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
As it is clear that the driver is licensed under the terms of GPLv2-only
by now, add a matching SPDX license identifier to all driver files.
Cc: Ralph Metzler <rjkm@metzlerbros.de>
Cc: Manfred Voelkel <mvoelkel@DigitalDevices.de>
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The stv0910.h doesn't carry any header nor any licensing boilerplate at
all, so copy this from the main driver file stv0910.c.
[mchehab@kernel.org: kept only the part of this patch that copied
the license from stv0910.c into stv0910.h]
Cc: Ralph Metzler <rjkm@metzlerbros.de>
Cc: Manfred Voelkel <mvoelkel@DigitalDevices.de>
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
As it is clear that the driver is licensed under the terms of GPLv2-only
by now, add a matching SPDX license identifier to all driver files.
Cc: Ralph Metzler <rjkm@metzlerbros.de>
Cc: Manfred Voelkel <mvoelkel@DigitalDevices.de>
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
mxl5xx.h doesn't carry any licensing boilerplate at all right now, so copy
the boilerplate over from the main driver file mxl5xx.c. Also, mxl5xx_defs
is missing a part of the licensing boilerplate text, so add it.
[mchehab@kernel.org: kept only the part of this patch that copied
the license from mxl5xx.c into mxl5xx.h]
Cc: Ralph Metzler <rjkm@metzlerbros.de>
Cc: Manfred Voelkel <mvoelkel@DigitalDevices.de>
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Cleanup blank lines, remove wrong links to
http://www.gnu.org/copyleft/gpl.html (the driver is licensed under the
terms of GPLv2, but the link points to a copy of the GPLv3), and fix
the filename reference in ddbridge-i2c.h.
[mchehab@kernel.org: removed whitespace changes at the licensing text,
as we didn't get any acks from the authors with regards to changing
the text]
Cc: Ralph Metzler <rjkm@metzlerbros.de>
Cc: Manfred Voelkel <mvoelkel@DigitalDevices.de>
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Since the boilerplates and MODULE_LICENSE are now in sync regarding the
used license (GPL v2 only), add a matching GPLv2 SPDX license identifier
to all files of the ddbridge driver.
Cc: Ralph Metzler <rjkm@metzlerbros.de>
Cc: Manfred Voelkel <mvoelkel@DigitalDevices.de>
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In commit 3db30defab4b ("use correct MODULE_LINCESE for GPL v2 only
according to notice in header") in the upstream repository for the
mentioned four drivers at https://github.com/DigitalDevices/dddvb.git
(plus a few more which aren't part of the mainline kernel tree), the
MODULE_LICENSE was fixed to "GPL v2" and are now in sync with the
GPL copyright boilerplate. Apply this change to the kernel tree
drivers as well.
Cc: Ralph Metzler <rjkm@metzlerbros.de>
Cc: Manfred Voelkel <mvoelkel@DigitalDevices.de>
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Fix error handling of v4l2_ctrl creation by inspecting the ctrl.error flag
instead of testing for each returned value correctness.
As reported by Dan Carpenter returning PTR_ERR() on the v4l2_ctrl_new_std()
return value is also wrong, as that function return NULL on error.
While at there re-order the cleanup path to respect the operation inverse
order.
Fixes: aab7ed1c "media: i2c: Add driver for Aptina MT9V111"
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The strcpy() function is being deprecated upstream. Replace
it by the safer strscpy().
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The implementation of strscpy() is more robust and safer.
That's now the recommended way to copy NUL terminated strings.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add a V4L2 mem-to-mem scaler/CSC driver for the Pixel Pipeline (PXP)
version found on i.MX6ULL SoCs. A similar variant is used on i.MX7D.
Since this driver only uses the legacy pipeline, it should be reasonably
easy to extend it to work with the older PXP versions found on i.MX6UL,
i.MX6SX, i.MX6SL, i.MX28, and i.MX23.
The driver supports scaling and colorspace conversion. There is
currently no support for rotation, alpha-blending, and the LUTs.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The FWHT codec can also be used by userspace utilities and libraries, but
since the current license is GPL and not LGPL it is not possible to include
it in e.g. gstreamer, since LGPL is required for that.
Change the license of these four files to LGPL.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Tom aan de Wiel <tom.aandewiel@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If requests are not supported by the driver, then return EACCES, not
EPERM.
If you attempt to mix queueing buffers directly and using requests,
then EBUSY is returned instead of EPERM: once a specific queueing mode
has been chosen the queue is 'busy' if you attempt the other mode
(i.e. direct queueing vs via a request).
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The request reference count was decreased again once a reference to the
request object was taken. Postpone this until we finished using the object.
In theory I think it is possible that the request_fd can be closed by
the application from another thread. In that case when request_put is
called the whole request would be freed.
It's highly unlikely, but let's just be safe and fix this potential
race condition.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
When getting control values from a completed request, we have
to protect the request against being re-inited when it is
being accessed by calling media_request_(un)lock_for_access.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add helper functions to prevent a completed request from being
re-inited while it is being accessed.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Set the capabilities field of v4l2_requestbuffers and v4l2_create_buffers.
The various mapping modes were easy, but for signaling the request capability
a new 'supports_requests' bitfield was added to videobuf2-core.h (and set in
vim2m and vivid). Drivers have to set this bitfield for any queue where
requests are supported.
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
For now (this might be relaxed in the future) we do not allow getting
controls from a request that isn't completed. In that case we return
-EACCES. Update the documentation accordingly.
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Instead of returning -ENOENT when a request_fd was not found (VIDIOC_QBUF
and VIDIOC_G/S/TRY_EXT_CTRLS), we now return -EINVAL. This is in line
with what we do when invalid dmabuf fds are passed to e.g. VIDIOC_QBUF.
Also document that EINVAL is returned for invalid m.fd values, we never
documented that.
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
D4M is a mobile model from the D4XX family of Intel RealSense cameras.
This patch adds a descriptor for it, which enables reading per-frame
metadata from it.
Signed-off-by: Guennadi Liakhovetski <guennadi.liakhovetski@intel.com>
[laurent.pinchart@ideasonboard.com Small clarifications to the documentation]
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The device information structure is currently copied field by field in
the uvc_device structure. As we only have two fields at the moment this
isn't much of an issue, but it prevents easy addition of new info
fields.
Fix this by storing the uvc_device_info pointer in the uvc_device
structure. As a result the uvc_device meta_format field can be removed.
The quirks field, however, needs to stay as it can be modified through a
module parameter.
As not all device have an information structure, we declare a global
"NULL" info instance that is used as a fallback when the driver_info is
empty.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The UVC_QUIRK_INFO macro defines "device information containing quirks",
not "quirks for information". Rename it to UVC_INFO_QUIRK.
Signed-off-by: Guennadi Liakhovetski <guennadi.liakhovetski@intel.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The use of ALIGN() in uvc_alloc_entity() is incorrect, since the size of
(entity->pads) is not a power of two. As a stop-gap, until a better
solution is adapted, use roundup() instead.
Found by a static assertion. Compile-tested only.
Fixes: 4ffc2d89f3 ("uvcvideo: Register subdevices for each entity")
Signed-off-by: Nadav Amit <namit@vmware.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
debugfs_remove_recursive() accepts a NULL parameter and returns
immediately, there's no need for a NULL check in the caller.
This issue was detected with the help of Coccinelle.
[Reword commit message, address uvc_debugfs_cleanup_stream()]
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The menu_info field of the uvc_control_mapping structure points to an
array of menu info data that are never changed by the driver. Make the
pointer const and constify the related static arrays in the driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Move some data to text
$ size drivers/media/usb/uvc/uvc_ctrl.o*
text data bss dec hex filename
34323 2364 0 36687 8f4f drivers/media/usb/uvc/uvc_ctrl.o.new
28659 8028 0 36687 8f4f drivers/media/usb/uvc/uvc_ctrl.o.old
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
drivers/media/platform/vicodec/vicodec-core.c:160:25: warning: variable 'q_out' set but not used [-Wunused-but-set-variable]
It's indeed not used, and it can be removed.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The initial sizeimage for the compressed decoder output was wrong.
The size of the output was incorrectly used to calculate the image
size, that should have been the size of the capture.
Rework the code to fix this.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Z16 support is identical to Y16, so that's easy to add.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Sakari Ailus