Since transparent huge pages, checking whether memory cgroups are below
their limits is no longer enough, but the actual amount of chargeable
space is important.
To not have more than one limit-checking interface, replace
memory_cgroup_check_under_limit() and memory_cgroup_check_margin() with a
single memory_cgroup_margin() that returns the chargeable space and leaves
the comparison to the callsite.
Soft limits are now checked the other way round, by using the already
existing function that returns the amount by which soft limits are
exceeded: res_counter_soft_limit_excess().
Also remove all the corresponding functions on the res_counter side that
are now no longer used.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Acked-by: Balbir Singh <balbir@linux.vnet.ibm.com>
Cc: Minchan Kim <minchan.kim@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Soft limit reclaim continues until the usage is below the current soft
limit, but the documented semantics are actually that soft limit reclaim
will push usage back until the soft limits are met again.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Acked-by: Balbir Singh <balbir@linux.vnet.ibm.com>
Cc: Minchan Kim <minchan.kim@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
minix bit operations are only used by minix filesystem and useless by
other modules. Because byte order of inode and block bitmaps is different
on each architecture like below:
m68k:
big-endian 16bit indexed bitmaps
h8300, microblaze, s390, sparc, m68knommu:
big-endian 32 or 64bit indexed bitmaps
m32r, mips, sh, xtensa:
big-endian 32 or 64bit indexed bitmaps for big-endian mode
little-endian bitmaps for little-endian mode
Others:
little-endian bitmaps
In order to move minix bit operations from asm/bitops.h to architecture
independent code in minix filesystem, this provides two config options.
CONFIG_MINIX_FS_BIG_ENDIAN_16BIT_INDEXED is only selected by m68k.
CONFIG_MINIX_FS_NATIVE_ENDIAN is selected by the architectures which use
native byte order bitmaps (h8300, microblaze, s390, sparc, m68knommu,
m32r, mips, sh, xtensa). The architectures which always use little-endian
bitmaps do not select these options.
Finally, we can remove minix bit operations from asm/bitops.h for all
architectures.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Andreas Schwab <schwab@linux-m68k.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Michal Simek <monstr@monstr.eu>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Cc: Chris Zankel <chris@zankel.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As the result of conversions, there are no users of ext2 non-atomic bit
operations except for ext2 filesystem itself. Now we can put them into
architecture independent code in ext2 filesystem, and remove from
asm/bitops.h for all architectures.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Jan Kara <jack@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As a preparation for removing ext2 non-atomic bit operations from
asm/bitops.h. This converts ext2 non-atomic bit operations to
little-endian bit operations.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As a preparation for removing ext2 non-atomic bit operations from
asm/bitops.h. This converts ext2 non-atomic bit operations to
little-endian bit operations.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Jan Kara <jack@suse.cz>
Cc: Andreas Dilger <adilger.kernel@dilger.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As a preparation for removing ext2 non-atomic bit operations from
asm/bitops.h. This converts ext2 non-atomic bit operations to
little-endian bit operations.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Introduce little-endian bit operations to the big-endian architectures
which do not have native little-endian bit operations and the
little-endian architectures. (alpha, avr32, blackfin, cris, frv, h8300,
ia64, m32r, mips, mn10300, parisc, sh, sparc, tile, x86, xtensa)
These architectures can just include generic implementation
(asm-generic/bitops/le.h).
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Mikael Starvik <starvik@axis.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Matthew Wilcox <willy@debian.org>
Cc: Grant Grundler <grundler@parisc-linux.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Kazumoto Kojima <kkojima@rr.iij4u.or.jp>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Chris Zankel <chris@zankel.net>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Acked-by: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This makes the little-endian bitops take any pointer types by changing the
prototypes and adding casts in the preprocessor macros.
That would seem to at least make all the filesystem code happier, and they
can continue to do just something like
#define ext2_set_bit __test_and_set_bit_le
(or whatever the exact sequence ends up being).
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Mikael Starvik <starvik@axis.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Matthew Wilcox <willy@debian.org>
Cc: Grant Grundler <grundler@parisc-linux.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Kazumoto Kojima <kkojima@rr.iij4u.or.jp>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Chris Zankel <chris@zankel.net>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch series introduces little-endian bit operations in asm/bitops.h
for all architectures and converts all ext2 non-atomic and minix bit
operations to use little-endian bit operations. It enables us to remove
ext2 non-atomic and minix bit operations from asm/bitops.h. The reason
they should be removed from asm/bitops.h is as follows:
For ext2 non-atomic bit operations, they are used for little-endian byte
order bitmap access by some filesystems and modules. But using ext2_*()
functions on a module other than ext2 filesystem makes some feel strange.
For minix bit operations, they are only used by minix filesystem and are
useless by other modules. Because byte order of inode and block bitmap is
This patch:
In order to make the forthcoming changes smaller, this merges macro
definisions in asm-generic/bitops/le.h for big-endian and little-endian as
much as possible.
This also removes unused BITOP_WORD macro.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This stops code that handles widgets generically from attempting to access
registers for these widgets.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Cc: stable@kernel.org
Introduce Kconfig option allowing architectures where sysdev
operations used during system suspend, resume and shutdown have been
completely replaced with struct sycore_ops operations to avoid
building sysdev code that will never be used.
Make callbacks in struct sys_device and struct sysdev_driver depend
on ARCH_NO_SYSDEV_OPS to allows us to verify if all of the references
have been actually removed from the code the given architecture
depends on.
Make x86 select ARCH_NO_SYSDEV_OPS.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
There are no users of OF_NO_DEEP_PROBE, and of_match_node() now
gracefully handles being passed a NULL pointer, so the checks at the
top of of_platform_bus_probe can be dropped.
While at it, consolidate the root node pointer check to be easier to
read and tidy up related comments.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Provide an alternative to access_process_vm that allows the caller to obtain a
reference to the supplied mm_struct.
Signed-off-by: Stephen Wilson <wilsons@start.ca>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Now that gate vma's are referenced with respect to a particular mm and not a
particular task it only makes sense to propagate the change to this predicate as
well.
Signed-off-by: Stephen Wilson <wilsons@start.ca>
Reviewed-by: Michel Lespinasse <walken@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Morally, the question of whether an address lies in a gate vma should be asked
with respect to an mm, not a particular task. Moreover, dropping the dependency
on task_struct will help make existing and future operations on mm's more
flexible and convenient.
Signed-off-by: Stephen Wilson <wilsons@start.ca>
Reviewed-by: Michel Lespinasse <walken@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Morally, the presence of a gate vma is more an attribute of a particular mm than
a particular task. Moreover, dropping the dependency on task_struct will help
make both existing and future operations on mm's more flexible and convenient.
Signed-off-by: Stephen Wilson <wilsons@start.ca>
Reviewed-by: Michel Lespinasse <walken@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The filelayout driver sends LAYOUTCOMMIT only when COMMIT goes to
the data server (as opposed to the MDS) and the data server WRITE
is not NFS_FILE_SYNC.
Only whole file layout support means that there is only one IOMODE_RW layout
segment.
Signed-off-by: Andy Adamson <andros@netapp.com>
Signed-off-by: Alexandros Batsakis <batsakis@netapp.com>
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: Dean Hildebrand <dhildeb@us.ibm.com>
Signed-off-by: Fred Isaman <iisaman@citi.umich.edu>
Signed-off-by: Mingyang Guo <guomingyang@nrchpc.ac.cn>
Signed-off-by: Tao Guo <guotao@nrchpc.ac.cn>
Signed-off-by: Zhang Jingwang <zhangjingwang@nrchpc.ac.cn>
Tested-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: Benny Halevy <bhalevy@panasas.com>
Signed-off-by: Fred Isaman <iisaman@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Implement all the hooks created in the previous patches.
This requires exporting quite a few functions and adding a few
structure fields.
Signed-off-by: Fred Isaman <iisaman@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
We create three major hooks for the pnfs code.
pnfs_mark_request_commit() is called during writeback_done from
nfs_mark_request_commit, which gives the driver an opportunity to
claim it wants control over commiting a particular req.
pnfs_choose_commit_list() is called from nfs_scan_list
to choose which list a given req should be added to, based on
where we intend to send it for COMMIT. It is up to the driver
to have preallocated list headers for each destination it may need.
pnfs_commit_list() is how the driver actually takes control, it is
used instead of nfs_commit_list().
In order to pass information between the above functions, we create
a union in nfs_page to hold a lseg (which is possible because the req is
not on any list while in transition), and add some flags to indicate
if we need to use the pnfs code.
Signed-off-by: Fred Isaman <iisaman@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Using blue flame can improve latency by allowing the HW to more efficiently
access the WQE. This patch presents two functions that are used to allocate or
release HW resources for using blue flame; the caller need to supply a struct
mlx4_bf object when allocating resources. Consumers that make use of this API
should post doorbells to the UAR object pointed by the initialized struct
mlx4_bf;
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mlx4_en module now uses the new steering mechanism.
The RX packets are now steered through the MCG table instead
of Mac table for unicast, and default entry for multicast.
The feature is enabled through INIT_HCA
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
The same packet steering mechanism would be used both for IB and Ethernet,
Both multicasts and unicasts.
This commit prepares the general infrastructure for this.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
HW revision is derived from device ID and rev id.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il>
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver queries the FW for WOL support.
Ethtool get/set_wol is implemented accordingly.
Only magic packets are supported at the time.
Signed-off-by: Igor Yarovinsky <igory@mellanox.co.il>
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding a pool of MSI-X vectors and EQs that can be used explicitly by mlx4_core
customers (mlx4_ib, mlx4_en). The consumers will assign their own names to the
interrupt vectors. Those vectors are not opened at mlx4 device initialization,
opened by demand.
Changed the max number of possible EQs according to the new scheme, no longer relies on
on number of cores.
The new functionality is exposed through mlx4_assign_eq() and mlx4_release_eq().
Customers that do not use the new API will get completion vectors as before.
Signed-off-by: Markuze Alex <markuze@mellanox.co.il>
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some irq_set_type() callbacks need to change the chip and the handler
when the trigger mode changes. We have already a (misnomed) setter
function for the handler which can be called from irq_set_type().
Provide one which allows to set chip and name as well. Put the
misnomed function under the COMPAT switch and provide a replacement.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Some irq chips need to call genirq functions for nested chips from
their callbacks. That upsets lockdep. So they need to set a different
lock class for those nested chips. Provide a helper function to avoid
open access to irq_desc.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Some filesystems (such as ext4) can return the same cookie value for
multiple files. If we try to start a readdir with one of these cookies,
the server will return the first file found with a cookie of the same
value. This can cause the client to enter an infinite loop.
Signed-off-by: Bryan Schumaker <bjschuma@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
nfs_opendir() created a context that held much more information than we
need for a readdir. This patch introduces a slimmed-down
nfs_open_dir_context that contains only the cookie and the cred used for
RPC operations. The new context will eventually be used to help detect
readdir loops.
Signed-off-by: Bryan Schumaker <bjschuma@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
The xmit path can sleep with a page kmapped in the network
xmit code while it waits for space to open up, so we have to use
kmap instead of kmap atomic in that path.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch adds a target_core_mib.c statistics conversion for
backend context struct se_subsystem_dev + struct se_device config_group
based statistics in target_core_device.c using CONFIGFS_EATTR()
based struct config_item_types from target_core_stat.c code.
The conversion from backend /proc/scsi_target/mib/ context output to configfs
default groups+attributes include scsi_dev, scsi_lu, and scsi_tgt_dev output
from within individual:
/sys/kernel/config/target/core/$HBA/DEV/
The legacy procfs output now appear as individual configfs attributes under:
*) $HBA/$DEV/statistics/scsi_dev:
|-- indx
|-- inst
|-- ports
`-- role
*) $HBA/$DEV/statistics/scsi_lu:
|-- creation_time
|-- dev
|-- dev_type
|-- full_stat
|-- hs_num_cmds
|-- indx
|-- inst
|-- lu_name
|-- lun
|-- num_cmds
|-- prod
|-- read_mbytes
|-- resets
|-- rev
|-- state_bit
|-- status
|-- vend
`-- write_mbytes
*) $HBA/$DEV/statistics/scsi_tgt_dev:
|-- indx
|-- inst
|-- non_access_lus
|-- num_lus
|-- resets
`-- status
The conversion from backend /proc/scsi_target/mib/ context output to configfs
default groups+attributes include scsi_port, scsi_tgt_port and scsi_transport
output from within individual:
/sys/kernel/config/target/fabric/$WWN/tpgt_$TPGT/lun/lun_$LUN_ID/statistics/
The legacy procfs output now appear as individual configfs attributes under:
*) fabric/$WWN/tpgt_$TPGT/lun/lun_$LUN_ID/statistics/scsi_port
|-- busy_count
|-- dev
|-- indx
|-- inst
`-- role
*) fabric/$WWN/tpgt_$TPGT/lun/lun_$LUN_ID/statistics/scsi_tgt_port
|-- dev
|-- hs_in_cmds
|-- in_cmds
|-- indx
|-- inst
|-- name
|-- port_index
|-- read_mbytes
`-- write_mbytes
*) fabric/$WWN/tpgt_$TPGT/lun/lun_$LUN_ID/statistics/scsi_transport
|-- dev_name
|-- device
|-- indx
`-- inst
The conversion from backend /proc/scsi_target/mib/ context output to configfs
default groups+attributes include scsi_att_intr_port and scsi_auth_intr output
from within individual:
/sys/kernel/config/target/fabric/$WWN/tpgt_$TPGT/acls/$INITIATOR_WWN/lun_$LUN_ID/statistics/
The legacy procfs output now appear as individual configfs attributes under:
*) acls/$INITIATOR_WWN/lun_$LUN_ID/statistics/scsi_att_intr_port
|-- dev
|-- indx
|-- inst
|-- port
|-- port_auth_indx
`-- port_ident
*) acls/$INITIATOR_WWN/lun_$LUN_ID/statistics/scsi_auth_intr
|-- att_count
|-- creation_time
|-- dev
|-- dev_or_port
|-- hs_num_cmds
|-- indx
|-- inst
|-- intr_name
|-- map_indx
|-- num_cmds
|-- port
|-- read_mbytes
|-- row_status
`-- write_mbytes
Also, this includes adding struct target_fabric_configfs_template->
tfc_wwn_fabric_stats_cit and ->tfc_tpg_nacl_stat_cit respectively for
use during target_core_fabric_configfs.c:target_fabric_setup_cits()
Signed-off-by: Nicholas A. Bellinger <nab@linux-iscsi.org>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch changes include/target/target_core_tmr.h code to use
target specific 'TMR_*' prefixed definitions for fabric independent
SCSI Task Management Request/Request naming in include/scsi/scsi.h
definitions for mainline target code.
Signed-off-by: Nicholas A. Bellinger <nab@linux-iscsi.org>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Reported-by: Fubo Chen <fubo.chen@gmail.com>
Cc: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Nicholas A. Bellinger <nab@linux-iscsi.org>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch addresses the majority of sparse warnings and adds
proper locking annotations. It also fixes the dubious one-bit signed
bitfield, for which the signed one-bit types can be 0 or -1 which can
cause a problem if someone ever checks if (foo->lu_gp_assoc == 1).
The current code is fine because everyone just checks zero vs non-zero.
But Sparse complains about it so lets change it. The warnings look like
this:
include/target/target_core_base.h:228:26: error: dubious one-bit signed bitfield
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Fubo Chen <fubo.chen@gmail.com>
Signed-off-by: Nicholas A. Bellinger <nab@linux-iscsi.org>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
During device discovery, scsi mid layer sends INQUIRY command to LUN
0. If the LUN 0 is not mapped to host, it creates a temporary
scsi_device with LUN id 0 and sends REPORT_LUNS command to it. After
the REPORT_LUNS succeeds, it walks through the LUN table and adds each
LUN found to sysfs. At the end of REPORT_LUNS lun table scan, it will
delete the temporary scsi_device of LUN 0.
When scsi devices are added to sysfs, it calls add_dev function of all
the registered class interfaces. If ses driver has been registered,
ses_intf_add() of ses module will be called. This function calls
scsi_device_enclosure() to check the inquiry data for EncServ
bit. Since inquiry was not allocated for temporary LUN 0 scsi_device,
it will cause NULL pointer exception.
To fix the problem, sdev->inquiry is checked for NULL before reading it.
Signed-off-by: Somasundaram Krishnasamy <Somasundaram.Krishnasamy@lsi.com>
Signed-off-by: Babu Moger <babu.moger@lsi.com>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch solves a stale pointer problem in
update_cgrp_time_from_cpuctx(). The cpuctx->cgrp
was not cleared on all possible event exit paths,
including:
close()
perf_release()
perf_release_kernel()
list_del_event()
This patch fixes list_del_event() to clear cpuctx->cgrp
when there are no cgroup events left in the context.
[ This second version makes the code compile when
CONFIG_CGROUP_PERF is not enabled. We unconditionally define
perf_cpu_context->cgrp. ]
Signed-off-by: Stephane Eranian <eranian@google.com>
Cc: peterz@infradead.org
Cc: perfmon2-devel@lists.sf.net
Cc: paulus@samba.org
Cc: davem@davemloft.net
LKML-Reference: <20110323150306.GA1580@quad>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Commit 34db18a054 ("smp: move smp setup functions to kernel/smp.c")
causes this build error on s390 because of a missing init.h include:
CC arch/s390/kernel/asm-offsets.s
In file included from /home2/heicarst/linux-2.6/arch/s390/include/asm/spinlock.h:14:0,
from include/linux/spinlock.h:87,
from include/linux/seqlock.h:29,
from include/linux/time.h:8,
from include/linux/timex.h:56,
from include/linux/sched.h:57,
from arch/s390/kernel/asm-offsets.c:10:
include/linux/smp.h:117:20: error: expected '=', ',', ';', 'asm' or '__attribute__' before 'setup_nr_cpu_ids'
include/linux/smp.h:118:20: error: expected '=', ',', ';', 'asm' or '__attribute__' before 'smp_init'
Fix it by adding the include statement.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Acked-by: WANG Cong <amwang@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The sentence uses the possessive pronoun, which is spelled
without an apostrophe.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Cc: Jiri Kosina <trivial@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
LKML-Reference: <1300735487-2406-1-git-send-email-j.neuschaefer@gmx.net>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Rename AB8500 GPADC header so as not to be redunantly named.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Allow const buffers to be passed in without type safety issues.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This adds a subdriver for the regulator found inside the TPS61050
and TPS61052 chips.
Cc: Samuel Ortiz <samuel.ortiz@intel.com>
Cc: Ola Lilja <ola.o.lilja@stericsson.com>
Cc: Jonas Aberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The TPS61050/TPS61052 are boost converters, LED drivers, LED flash
drivers and a simple GPIO pin chips.
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Jonas Aberg <jonas.aberg@stericsson.com>
Cc: Ola Lilja <ola.o.lilja@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch supports PMIC/Regulator part of MAX8997/MAX8966 MFD.
In this initial release, selecting voltages or current-limit
and switching on/off the regulators are supported.
Controlling voltages for DVS with GPIOs is not implemented fully
and requires more considerations: it controls multiple bucks (selection
of 1, 2, and 5) at the same time with SET1~3 gpios. Thus, when DVS-GPIO
is activated, we lose the ability to control the voltage of a single
buck regulator independently; i.e., contolling a buck affects other two
bucks. Therefore, using the conventional regulator framework directly
might be problematic. However, in this driver, we try to choose
a setting without such side effect of affecting other regulators and
then try to choose a setting with the minimum side effect (the sum of
voltage changes in other regulators).
On the other hand, controlling all the three bucks simultenously based
on the voltage set table may help build cpufreq and similar system
more robust; i.e., all the three voltages are consistent every time
without glitches during transition.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Append the additional read/write operation on 88pm860x for accessing
test page in 88PM860x.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Copy 88pm860x platform data into different mfd_data structure for
regulator driver. So move the identification of device node from
regulator driver to mfd driver.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Copy 88pm860x platform data into different mfd_data structure for
led driver. So move the identification of device node from led
driver to mfd driver.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Copy 88pm860x platform data into different mfd_data structure for
backlight driver. So move the identification of device node from
backlight driver to mfd driver.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This revamps the interface so that AB8500 GPADCs are fetched by
name. Probed GPADCs are added to a list and this list is searched
for a matching GPADC. This makes it possible to have multiple
AB8500 GPADC instances instead of it being a singleton, and
rids the need to keep a GPADC pointer around in the core AB8500
MFD struct.
Currently the match is made to the device name which is by default
numbered from the device instance such as "ab8500-gpadc.0" but
by using the .init_name field of the device a more intiutive
naming for the GPADC blocks can be achieved if desired.
Signed-off-by: Daniel Willerud <daniel.willerud@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This moves the ab8500-gpadc.h header down into the ab8500/
subdir in include/linux/mfd and fixes some whitespace in the
header in the process.
Signed-off-by: Daniel Willerud <daniel.willerud@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
MAX8997/MAX8966 chip is a multi-function device with I2C bussses. The
chip includes PMIC, RTC, Fuel Gauge, MUIC, Haptic, Flash control, and
Battery (charging) control.
This patch is an initial release of a MAX8997/8966 driver that supports
to enable the chip with its primary I2C bus that connects every device
mentioned above except for Fuel Gauge, which uses another I2C bus. The
fuel gauge is not supported by this mfd driver and is supported by a
seperated driver of MAX17042 Fuel Gauge (yes, the fuel gauge part is
compatible with MAX17042).
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
As requested by Samuel, there's not really any reason to have "shared"
in the name.
This also modifies the only user of the function, as well.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch adds support for ab8500 chip revision cut 3.0.
Also rephrased from Changes to Author in the header.
Signed-off-by: Mattias Wallin <mattias.wallin@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
If a system contains multiple WM831x devices we need to pass a device
number through to the MFD so that we use unique device IDs when we
instantiate child devices. In order to get support for this into 2.6.39
add some platform data to support the configuration, but no implementation
as yet.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Introducing a driver for MADC on TWL4030 powerIC. MADC stands for monitoring
ADC. This driver monitors the real time conversion of analog signals like
battery temperature, battery cuurent etc.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This adds functions to enable platform_device sharing for mfd clients.
Each platform driver (mfd client) that wants to share an mfd_cell's
platform_device uses the mfd_shared_platform_driver_{un,}register()
functions instead of platform_driver_{un,}register(). Along with
registering the platform driver, these also register a new platform
device with the same characteristics as the original cell, but a different
name. Given an mfd_cell with the name "foo", drivers that want to
share access to its resources can call mfd_shared_platform_driver_register
with platform drivers named (for example) "bar" and "baz". This
will register two platform devices and drivers named "bar" and "baz"
that share the same cell as the platform device "foo". The drivers
can then call "foo" cell's enable hooks (or mfd_shared_cell_enable)
to enable resources, and obtain platform resources as they normally
would.
This deals with platform handling only; mfd driver-specific details,
hardware handling, refcounting, etc are all dealt with separately.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This provides convenience functions for sharing of cells across
multiple mfd clients. Mfd drivers can provide enable/disable hooks
to actually tweak the hardware, and clients can call
mfd_shared_cell_{en,dis}able without having to worry about whether
or not another client happens to have enabled or disabled the
cell/hardware.
Note that this is purely optional; drivers can continue to use
the mfd_cell's enable/disable hooks for their own purposes, if
desired.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
All users of this have now been switched over to using mfd_data;
it can go away now.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Rename the platform_data variable to imply a distinction between
common platform_data driver usage (typically accessed via
pdev->dev.platform_data) and the way MFD passes data down to
clients (using a wrapper named mfd_get_data).
All clients have already been changed to use the wrapper function,
so this can be a quick single-commit change that only touches things
in drivers/mfd.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Now that there are no more users of this, drop it.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The cell's platform_data is now accessed with a helper function;
change clients to use that, and remove the now-unused data_size.
Note that mfd-core no longer makes a copy of platform_data, but the
mc13xxx-core driver creates the pdata structures on the stack. In
order to get around that, the various ARM mach types that set the
pdata have been changed to hold the variable in static (global) memory.
Also note that __initdata references in aforementioned pdata structs
have been dropped.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
No clients (in mainline kernel, I'm told that drivers exist in external
trees that are planned for mainline inclusion) make use of this, nor
do they make use of platform_data, so nothing really had to change here.
The .data_size field is unused, so its usage gets removed.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Previously, one would set the mfd_cell's platform_data/data_size to point
to the current mfd_cell in order to pass that information along to drivers.
This causes the current mfd_cell to always be available to drivers. It
also adds a wrapper function for fetching the mfd cell from a platform
device, similar to what originally existed for mfd devices.
Drivers who previously used platform_data for other purposes can still
use it; the difference is that mfd_get_data() must be used to
access it (and the pdata structure is no longer allocated in
mfd_add_devices).
Note that mfd_get_data is intentionally vague (in name) about where
the data is stored; variable name changes can come later without having
to touch brazillions of drivers.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In OMAP4 Blaze and Panda, 32KHz clock to WLAN is supplied from Phoenix
TWL6030. The 32KHz clock state (ON/OFF) is configured in
CLK32KG_CFG_[GRP, TRANS, STATE] register. This follows the same register
programming model as other regulators in TWL6030. So add CLK32KG as pseudo
regulator.
Signed-off-by: Balaji T K <balajitk@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This adds a pretty straight-forward system control driver for the
AB8500. This driver will be used from the core platform, e.g the
clock tree implementation in the machine code, and is by nature
singleton.
There are a few simple functions to read, write, set and clear
registers so that the machine code can control its own foundation.
Cc: Mattias Wallin <mattias.wallin@stericsson.com>
Signed-off-by: Mattias Nilsson <mattias.i.nilsson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Provide platform data allowing the system to set the /IRQ pin into
CMOS mode rather than the default open drain. The default value of
this platform data reflects the default hardware configuration so
there should be no change to existing users.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Version 20110316.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
We finally have the definition for this table.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
With recent changes to the driver(switch to new cpdma layer),
the support for buffer descriptor address translation logic
is broken. This affects platforms where the physical address of
the descriptors as seen by the DMA engine is different from the
physical address.
Original Patch adding translation logic support:
Commit: ad021ae886
Signed-off-by: Sriramakrishnan A G <srk@ti.com>
Tested-By: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This avoids explicit cast to avoid 'discards qualifiers'
compiler warning in a netfilter patch that i've been working on.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx: (66 commits)
avr32: at32ap700x: fix typo in DMA master configuration
dmaengine/dmatest: Pass timeout via module params
dma: let IMX_DMA depend on IMX_HAVE_DMA_V1 instead of an explicit list of SoCs
fsldma: make halt behave nicely on all supported controllers
fsldma: reduce locking during descriptor cleanup
fsldma: support async_tx dependencies and automatic unmapping
fsldma: fix controller lockups
fsldma: minor codingstyle and consistency fixes
fsldma: improve link descriptor debugging
fsldma: use channel name in printk output
fsldma: move related helper functions near each other
dmatest: fix automatic buffer unmap type
drivers, pch_dma: Fix warning when CONFIG_PM=n.
dmaengine/dw_dmac fix: use readl & writel instead of __raw_readl & __raw_writel
avr32: at32ap700x: Specify DMA Flow Controller, Src and Dst msize
dw_dmac: Setting Default Burst length for transfers as 16.
dw_dmac: Allow src/dst msize & flow controller to be configured at runtime
dw_dmac: Changing type of src_master and dest_master to u8.
dw_dmac: Pass Channel Priority from platform_data
dw_dmac: Pass Channel Allocation Order from platform_data
...
Instead of always creating a huge (268K) deflate_workspace with the
maximum compression parameters (windowBits=15, memLevel=8), allow the
caller to obtain a smaller workspace by specifying smaller parameter
values.
For example, when capturing oops and panic reports to a medium with
limited capacity, such as NVRAM, compression may be the only way to
capture the whole report. In this case, a small workspace (24K works
fine) is a win, whether you allocate the workspace when you need it (i.e.,
during an oops or panic) or at boot time.
I've verified that this patch works with all accepted values of windowBits
(positive and negative), memLevel, and compression level.
Signed-off-by: Jim Keniston <jkenisto@us.ibm.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: David Miller <davem@davemloft.net>
Cc: Chris Mason <chris.mason@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add brackets around typecasted argument in crc32() macro.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@openvz.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Analog Devices' SigmaStudio can produce firmware blobs for devices with
these DSPs embedded (like some audio codecs). Allow these device drivers
to easily parse and load them.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
1. simple_strto*() do not contain overflow checks and crufty,
libc way to indicate failure.
2. strict_strto*() also do not have overflow checks but the name and
comments pretend they do.
3. Both families have only "long long" and "long" variants,
but users want strtou8()
4. Both "simple" and "strict" prefixes are wrong:
Simple doesn't exactly say what's so simple, strict should not exist
because conversion should be strict by default.
The solution is to use "k" prefix and add convertors for more types.
Enter
kstrtoull()
kstrtoll()
kstrtoul()
kstrtol()
kstrtouint()
kstrtoint()
kstrtou64()
kstrtos64()
kstrtou32()
kstrtos32()
kstrtou16()
kstrtos16()
kstrtou8()
kstrtos8()
Include runtime testsuite (somewhat incomplete) as well.
strict_strto*() become deprecated, stubbed to kstrto*() and
eventually will be removed altogether.
Use kstrto*() in code today!
Note: on some archs _kstrtoul() and _kstrtol() are left in tree, even if
they'll be unused at runtime. This is temporarily solution,
because I don't want to hardcode list of archs where these
functions aren't needed. Current solution with sizeof() and
__alignof__ at least always works.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
PTR_RET() can be used if you have an error-pointer and are only interested
in the eventual error value, but not the pointer. Yields the usual 0 for
no error, -ESOMETHING otherwise.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Re-ordering struct block_inode to remove 8 bytes of padding on 64 bit
builds, which also shrinks bdev_inode by 8 bytes (776 -> 768) allowing it
to fit into one fewer cache lines.
Signed-off-by: Richard Kennedy <richard@rsk.demon.co.uk>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
All architectures can use the common dma_addr_t typedef now. We can
remove the arch specific dma_addr_t.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Matt Turner <mattst88@gmail.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a new __GFP_OTHER_NODE flag to tell the low level numa statistics in
zone_statistics() that an allocation is on behalf of another thread. This
way the local and remote counters can be still correct, even when
background daemons like khugepaged are changing memory mappings.
This only affects the accounting, but I think it's worth doing that right
to avoid confusing users.
I first tried to just pass down the right node, but this required a lot of
changes to pass down this parameter and at least one addition of a 10th
argument to a 9 argument function. Using the flag is a lot less
intrusive.
Open: should be also used for migration?
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Reviewed-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When reclaiming for order-0 pages, kswapd requires that all zones be
balanced. Each cycle through balance_pgdat() does background ageing on
all zones if necessary and applies equal pressure on the inactive zone
unless a lot of pages are free already.
A "lot of free pages" is defined as a "balance gap" above the high
watermark which is currently 7*high_watermark. Historically this was
reasonable as min_free_kbytes was small. However, on systems using huge
pages, it is recommended that min_free_kbytes is higher and it is tuned
with hugeadm --set-recommended-min_free_kbytes. With the introduction of
transparent huge page support, this recommended value is also applied. On
X86-64 with 4G of memory, min_free_kbytes becomes 67584 so one would
expect around 68M of memory to be free. The Normal zone is approximately
35000 pages so under even normal memory pressure such as copying a large
file, it gets exhausted quickly. As it is getting exhausted, kswapd
applies pressure equally to all zones, including the DMA32 zone. DMA32 is
approximately 700,000 pages with a high watermark of around 23,000 pages.
In this situation, kswapd will reclaim around (23000*8 where 8 is the high
watermark + balance gap of 7 * high watermark) pages or 718M of pages
before the zone is ignored. What the user sees is that free memory far
higher than it should be.
To avoid an excessive number of pages being reclaimed from the larger
zones, explicitely defines the "balance gap" to be either 1% of the zone
or the low watermark for the zone, whichever is smaller. While kswapd
will check all zones to apply pressure, it'll ignore zones that meets the
(high_wmark + balance_gap) watermark.
To test this, 80G were copied from a partition and the amount of memory
being used was recorded. A comparison of a patch and unpatched kernel can
be seen at
http://www.csn.ul.ie/~mel/postings/minfree-20110222/memory-usage-hydra.ps
and shows that kswapd is not reclaiming as much memory with the patch
applied.
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Mel Gorman <mel@csn.ul.ie>
Acked-by: Rik van Riel <riel@redhat.com>
Cc: Shaohua Li <shaohua.li@intel.com>
Cc: "Chen, Tim C" <tim.c.chen@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Right now, if a mm_walk has either ->pte_entry or ->pmd_entry set, it will
unconditionally split any transparent huge pages it runs in to. In
practice, that means that anyone doing a
cat /proc/$pid/smaps
will unconditionally break down every huge page in the process and depend
on khugepaged to re-collapse it later. This is fairly suboptimal.
This patch changes that behavior. It teaches each ->pmd_entry handler
(there are five) that they must break down the THPs themselves. Also, the
_generic_ code will never break down a THP unless a ->pte_entry handler is
actually set.
This means that the ->pmd_entry handlers can now choose to deal with THPs
without breaking them down.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Dave Hansen <dave@linux.vnet.ibm.com>
Acked-by: Mel Gorman <mel@csn.ul.ie>
Acked-by: David Rientjes <rientjes@google.com>
Reviewed-by: Eric B Munson <emunson@mgebm.net>
Tested-by: Eric B Munson <emunson@mgebm.net>
Cc: Michael J Wolf <mjwolf@us.ibm.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Matt Mackall <mpm@selenic.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The rotate_reclaimable_page function moves just written out pages, which
the VM wanted to reclaim, to the end of the inactive list. That way the
VM will find those pages first next time it needs to free memory.
This patch applies the rule in memcg. It can help to prevent unnecessary
working page eviction of memcg.
Signed-off-by: Minchan Kim <minchan.kim@gmail.com>
Acked-by: Balbir Singh <balbir@linux.vnet.ibm.com>
Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Reviewed-by: Rik van Riel <riel@redhat.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Recently, there are reported problem about thrashing.
(http://marc.info/?l=rsync&m=128885034930933&w=2) It happens by backup
workloads(ex, nightly rsync). That's because the workload makes just
use-once pages and touches pages twice. It promotes the page into active
list so that it results in working set page eviction.
Some app developer want to support POSIX_FADV_NOREUSE. But other OSes
don't support it, either.
(http://marc.info/?l=linux-mm&m=128928979512086&w=2)
By other approach, app developers use POSIX_FADV_DONTNEED. But it has a
problem. If kernel meets page is writing during invalidate_mapping_pages,
it can't work. It makes for application programmer to use it since they
always have to sync data before calling fadivse(..POSIX_FADV_DONTNEED) to
make sure the pages could be discardable. At last, they can't use
deferred write of kernel so that they could see performance loss.
(http://insights.oetiker.ch/linux/fadvise.html)
In fact, invalidation is very big hint to reclaimer. It means we don't
use the page any more. So let's move the writing page into inactive
list's head if we can't truncate it right now.
Why I move page to head of lru on this patch, Dirty/Writeback page would
be flushed sooner or later. It can prevent writeout of pageout which is
less effective than flusher's writeout.
Originally, I reused lru_demote of Peter with some change so added his
Signed-off-by.
Signed-off-by: Minchan Kim <minchan.kim@gmail.com>
Reported-by: Ben Gamari <bgamari.foss@gmail.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Acked-by: Rik van Riel <riel@redhat.com>
Acked-by: Mel Gorman <mel@csn.ul.ie>
Reviewed-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Wu Fengguang <fengguang.wu@intel.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Nick Piggin <npiggin@kernel.dk>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Reorder mm_struct to remove 16 bytes of alignment padding on 64 bit
builds. On my config this shrinks mm_struct by enough to fit in one
fewer cache lines and allows more objects per slab in mm_struct
kmem_cache under SLUB.
slabinfo before patch :-
Sizes (bytes) Slabs
--------------------------------
Object : 848 Total : 9
SlabObj: 896 Full : 2
SlabSiz: 16384 Partial: 5
Loss : 48 CpuSlab: 2
Align : 64 Objects: 18
slabinfo after :-
Sizes (bytes) Slabs
--------------------------------
Object : 832 Total : 7
SlabObj: 832 Full : 2
SlabSiz: 16384 Partial: 3
Loss : 0 CpuSlab: 2
Align : 64 Objects: 19
Signed-off-by: Richard Kennedy <richard@rsk.demon.co.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
TestSetPageLocked() isn't being used anywhere. Also, using it would
likely be an error, since the proper interface trylock_page() provides
stronger ordering guarantees.
Signed-off-by: Michel Lespinasse <walken@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch changes the anon_vma refcount to be 0 when the object is free.
It does this by adding 1 ref to being in use in the anon_vma structure
(iow. the anon_vma->head list is not empty).
This allows a simpler release scheme without having to check both the
refcount and the list as well as avoids taking a ref for each entry on the
list.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Reviewed-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Acked-by: Hugh Dickins <hughd@google.com>
Acked-by: Mel Gorman <mel@csn.ul.ie>
Acked-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The normal code pattern used in the kernel is: get/put.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Reviewed-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Acked-by: Hugh Dickins <hughd@google.com>
Reviewed-by: Rik van Riel <riel@redhat.com>
Acked-by: Mel Gorman <mel@csn.ul.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now we renamed remove_from_page_cache with delete_from_page_cache. As
consistency of __remove_from_swap_cache and remove_from_swap_cache, we
change internal page cache handling function name, too.
Signed-off-by: Minchan Kim <minchan.kim@gmail.com>
Cc: Christoph Hellwig <hch@infradead.org>
Acked-by: Hugh Dickins <hughd@google.com>
Acked-by: Mel Gorman <mel@csn.ul.ie>
Reviewed-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Reviewed-by: Johannes Weiner <hannes@cmpxchg.org>
Reviewed-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now delete_from_page_cache() replaces remove_from_page_cache(). So we
remove remove_from_page_cache so fs or something out of mainline will
notice it when compile time and can fix it.
Signed-off-by: Minchan Kim <minchan.kim@gmail.com>
Cc: Christoph Hellwig <hch@infradead.org>
Acked-by: Hugh Dickins <hughd@google.com>
Acked-by: Mel Gorman <mel@csn.ul.ie>
Reviewed-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Reviewed-by: Johannes Weiner <hannes@cmpxchg.org>
Reviewed-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Presently we increase the page refcount in add_to_page_cache() but don't
decrease it in remove_from_page_cache(). Such asymmetry adds confusion,
requiring that callers notice it and a comment explaining why they release
a page reference. It's not a good API.
A long time ago, Hugh tried it (http://lkml.org/lkml/2004/10/24/140) but
gave up because reiser4's drop_page() had to unlock the page between
removing it from page cache and doing the page_cache_release(). But now
the situation is changed. I think at least things in current mainline
don't have any obstacles. The problem is for out-of-mainline filesystems
- if they have done such things as reiser4, this patch could be a problem
but they will discover this at compile time since we remove
remove_from_page_cache().
This patch:
This function works as just wrapper remove_from_page_cache(). The
difference is that it decreases page references in itself. So caller have
to make sure it has a page reference before calling.
This patch is ready for removing remove_from_page_cache().
Signed-off-by: Minchan Kim <minchan.kim@gmail.com>
Cc: Christoph Hellwig <hch@infradead.org>
Acked-by: Hugh Dickins <hughd@google.com>
Acked-by: Mel Gorman <mel@csn.ul.ie>
Reviewed-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Reviewed-by: Johannes Weiner <hannes@cmpxchg.org>
Reviewed-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Edward Shishkin <edward.shishkin@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This function basically does:
remove_from_page_cache(old);
page_cache_release(old);
add_to_page_cache_locked(new);
Except it does this atomically, so there's no possibility for the "add" to
fail because of a race.
If memory cgroups are enabled, then the memory cgroup charge is also moved
from the old page to the new.
This function is currently used by fuse to move pages into the page cache
on read, instead of copying the page contents.
[minchan.kim@gmail.com: add freepage() hook to replace_page_cache_page()]
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Acked-by: Rik van Riel <riel@redhat.com>
Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Signed-off-by: Minchan Kim <minchan.kim@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
GUP user may want to try to acquire a reference to a page if it is already
in memory, but not if IO, to bring it in, is needed. For example KVM may
tell vcpu to schedule another guest process if current one is trying to
access swapped out page. Meanwhile, the page will be swapped in and the
guest process, that depends on it, will be able to run again.
This patch adds FAULT_FLAG_RETRY_NOWAIT (suggested by Linus) and
FOLL_NOWAIT follow_page flags. FAULT_FLAG_RETRY_NOWAIT, when used in
conjunction with VM_FAULT_ALLOW_RETRY, indicates to handle_mm_fault that
it shouldn't drop mmap_sem and wait on a page, but return VM_FAULT_RETRY
instead.
[akpm@linux-foundation.org: improve FOLL_NOWAIT comment]
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Hugh Dickins <hughd@google.com>
Acked-by: Rik van Riel <riel@redhat.com>
Cc: Michel Lespinasse <walken@google.com>
Cc: Avi Kivity <avi@redhat.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The oom killer is extremely verbose for machines with a large number of
cpus and/or nodes. This verbosity can often be harmful if it causes other
important messages to be scrolled from the kernel log and incurs a
signicant time delay, specifically for kernels with CONFIG_NODES_SHIFT >
8.
This patch causes only memory information to be displayed for nodes that
are allowed by current's cpuset when dumping the VM state. Information
for all other nodes is irrelevant to the oom condition; we don't care if
there's an abundance of memory elsewhere if we can't access it.
This only affects the behavior of dumping memory information when an oom
is triggered. Other dumps, such as for sysrq+m, still display the
unfiltered form when using the existing show_mem() interface.
Additionally, the per-cpu pageset statistics are extremely verbose in oom
killer output, so it is now suppressed. This removes
nodes_weight(current->mems_allowed) * (1 + nr_cpus)
lines from the oom killer output.
Callers may use __show_mem(SHOW_MEM_FILTER_NODES) to filter disallowed
nodes.
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
All kthreads being created from a single helper task, they all use memory
from a single node for their kernel stack and task struct.
This patch suite creates kthread_create_on_node(), adding a 'cpu' parameter
to parameters already used by kthread_create().
This parameter serves in allocating memory for the new kthread on its
memory node if possible.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: David S. Miller <davem@davemloft.net>
Reviewed-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Tejun Heo <tj@kernel.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: David Howells <dhowells@redhat.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch reverts 5a03b051 ("thp: use compaction in kswapd for GFP_ATOMIC
order > 0") due to reports stating that kswapd CPU usage was higher and
IRQs were being disabled more frequently. This was reported at
http://www.spinics.net/linux/fedora/alsa-user/msg09885.html.
Without this patch applied, CPU usage by kswapd hovers around the 20% mark
according to the tester (Arthur Marsh:
http://www.spinics.net/linux/fedora/alsa-user/msg09899.html). With this
patch applied, it's around 2%.
The problem is not related to THP which specifies __GFP_NO_KSWAPD but is
triggered by high-order allocations hitting the low watermark for their
order and waking kswapd on kernels with CONFIG_COMPACTION set. The most
common trigger for this is network cards configured for jumbo frames but
it's also possible it'll be triggered by fork-heavy workloads (order-1)
and some wireless cards which depend on order-1 allocations.
The symptoms for the user will be high CPU usage by kswapd in low-memory
situations which could be confused with another writeback problem. While
a patch like 5a03b051 may be reintroduced in the future, this patch plays
it safe for now and reverts it.
[mel@csn.ul.ie: Beefed up the changelog]
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Mel Gorman <mel@csn.ul.ie>
Reported-by: Arthur Marsh <arthur.marsh@internode.on.net>
Tested-by: Arthur Marsh <arthur.marsh@internode.on.net>
Cc: <stable@kernel.org> [2.6.38.1]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In systems with multiple framebuffer devices, one of the devices might be
blanked while another is unblanked. In order for the backlight blanking
logic to know whether to turn off the backlight for a particular
framebuffer's blanking notification, it needs to be able to check if a
given framebuffer device corresponds to the backlight.
This plumbs the check_fb hook from core backlight through the
pwm_backlight helper to allow platform code to plug in a check_fb hook.
Signed-off-by: Robert Morell <rmorell@nvidia.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Arun Murthy <arun.murthy@stericsson.com>
Cc: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There may be multiple ways of controlling the backlight on a given
machine. Allow drivers to expose the type of interface they are
providing, making it possible for userspace to make appropriate policy
decisions.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: David Airlie <airlied@linux.ie>
Cc: Alex Deucher <alexdeucher@gmail.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Simple backlight driver for National Semiconductor LM3530. Presently only
manual mode is supported, PWM and ALS support to be added.
Signed-off-by: Shreshtha Kumar Sahu <shreshthakumar.sahu@stericsson.com>
Cc: Linus Walleij <linus.walleij@stericsson.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
syncfs() is duplicating name_to_handle_at() due to a merging mistake.
Cc: Sage Weil <sage@newdream.net>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'slab/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/slab-2.6:
slub: Add statistics for this_cmpxchg_double failures
slub: Add missing irq restore for the OOM path
* git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
rbd: use watch/notify for changes in rbd header
libceph: add lingering request and watch/notify event framework
rbd: update email address in Documentation
ceph: rename dentry_release -> d_release, fix comment
ceph: add request to the tail of unsafe write list
ceph: remove request from unsafe list if it is canceled/timed out
ceph: move readahead default to fs/ceph from libceph
ceph: add ino32 mount option
ceph: update common header files
ceph: remove debugfs debug cruft
libceph: fix osd request queuing on osdmap updates
ceph: preserve I_COMPLETE across rename
libceph: Fix base64-decoding when input ends in newline.
Using delayed-work for tty flip buffers ends up causing us to wait for
the next tick to complete some actions. That's usually not all that
noticeable, but for certain latency-critical workloads it ends up being
totally unacceptable.
As an extreme case of this, passing a token back-and-forth over a pty
will take two ticks per iteration, so even just a thousand iterations
will take 8 seconds assuming a common 250Hz configuration.
Avoiding the whole delayed work issue brings that ping-pong test-case
down to 0.009s on my machine.
In more practical terms, this latency has been a performance problem for
things like dive computer simulators (simulating the serial interface
using the ptys) and for other environments (Alan mentions a CP/M emulator).
Reported-by: Jef Driesen <jefdriesen@telenet.be>
Acked-by: Greg KH <gregkh@suse.de>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
dma_addr_t may not fit into void* on some architectures. To be safe, make
vb2_dma_contig_cookie() return a pointer to dma_addr_t and dereference it
in vb2_dma_contig_plane_paddr() back to dma_addr_t.
Signed-off-by: Pawel Osciak <pawel@osciak.com>
Reported-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This fixes the problem in which a host driver
sets a personalized sizeimage or bytesperline field,
and gets ignored when doing G_FMT.
Signed-off-by: Sergio Aguirre <saaguirre@ti.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There are two "hauppauge-new" keymaps, one with protocol
unknown, and the other with the protocol marked accordingly.
However, both tables are miss-named.
Also, the old rc-hauppauge-new is broken, as it mixes
three different controllers as if they were just one.
This patch solves half of the problem by renaming the
correct keycode table as just rc-hauppauge. This table
contains the codes for the four different types of
remote controllers found on Hauppauge cards, properly
mapped with their different addresses.
create mode 100644 drivers/media/rc/keymaps/rc-hauppauge.c
delete mode 100644 drivers/media/rc/keymaps/rc-rc5-hauppauge-new.c
[Jarod: fix up RC_MAP_HAUPPAUGE defines]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Rather than guess which driver supports core priority handling, require drivers
that do to explicitly set the V4L2_FL_USE_FH_PRIO flag in video_device.
Updated the core prio handling accordingly and set the flag in the three
drivers that do.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The video_device struct has proper ref counting and its release function
will be called when the last user releases it. But no such support was
available for struct v4l2_device. This made it hard to determine when a
USB driver can release the device if it has multiple device nodes.
With one device node it is easy of course, since when the device node is
released, the whole device can be released.
This patch adds refcounting to v4l2_device. When registering device nodes
the v4l2_device refcount will be increased, when releasing device nodes
it will be decreased. The (optional) release function will be called when
the last device node was released.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Drivers that use v4l2_fh can now use the core framework support of g/s_priority.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Several drivers need to do something when the first filehandle is opened
or the last filehandle is closed. Most implement some use count mechanism,
but if they use v4l2_fh, then you can also just check if this is the only
filehandle for the device node. A simple helper function can do this.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add two new functions: v4l2_fh_open allocates and initializes a struct v4l2_fh
based on a struct file pointer and v4l2_fh_release releases and frees a struct
v4l2_fh.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Integrate the v4l2_prio_state into the core, ready for use.
One struct v4l2_prio_state is added to v4l2_device and a pointer
to a prio state is added to video_device.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We are going to move priority handling into the v4l2 core. As a consequence
the v4l2_prio helper functions need to be moved into the core videodev
module as well to prevent circular dependencies.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Lingering requests are requests that are sent to the OSD normally but
tracked also after we get a successful request. This keeps the OSD
connection open and resends the original request if the object moves to
another OSD. The OSD can then send notification messages back to us
if another client initiates a notify.
This framework will be used by RBD so that the client gets notification
when a snapshot is created by another node or tool.
Signed-off-by: Yehuda Sadeh <yehuda@hq.newdream.net>
Signed-off-by: Sage Weil <sage@newdream.net>
* 'for-linus/2639/i2c-2' of git://git.fluff.org/bjdooks/linux:
i2c-pxa2xx: Don't clear isr bits too early
i2c-pxa2xx: Fix register offsets
i2c-pxa2xx: pass of_node from platform driver to adapter and publish
i2c-pxa2xx: check timeout correctly
i2c-pxa2xx: add support for shared IRQ handler
i2c-pxa2xx: Add PCI support for PXA I2C controller
ARM: pxa2xx: reorganize I2C files
i2c-pxa2xx: use dynamic register layout
i2c-mxs: set controller to pio queue mode after reset
i2c-eg20t: support new device OKI SEMICONDUCTOR ML7213 IOH
i2c/busses: Add support for Diolan U2C-12 USB-I2C adapter
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/slab-2.6:
slub: Dont define useless label in the !CONFIG_CMPXCHG_LOCAL case
slab,rcu: don't assume the size of struct rcu_head
slub,rcu: don't assume the size of struct rcu_head
slub: automatically reserve bytes at the end of slab
Lockless (and preemptless) fastpaths for slub
slub: Get rid of slab_free_hook_irq()
slub: min_partial needs to be in first cacheline
slub: fix ksize() build error
slub: fix kmemcheck calls to match ksize() hints
Revert "slab: Fix missing DEBUG_SLAB last user"
mm: Remove support for kmem_cache_name()
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (33 commits)
IPVS: Use global mutex in ip_vs_app.c
ipvs: fix a typo in __ip_vs_control_init()
veth: Fix the byte counters
net ipv6: Fix duplicate /proc/sys/net/ipv6/neigh directory entries.
macvlan: Fix use after free of struct macvlan_port.
net: fix incorrect spelling in drop monitor protocol
can: c_can: Do basic c_can configuration _before_ enabling the interrupts
net/appletalk: fix atalk_release use after free
ipx: fix ipx_release()
snmp: SNMP_UPD_PO_STATS_BH() always called from softirq
l2tp: fix possible oops on l2tp_eth module unload
xfrm: Fix initialize repl field of struct xfrm_state
netfilter: ipt_CLUSTERIP: fix buffer overflow
netfilter: xtables: fix reentrancy
netfilter: ipset: fix checking the type revision at create command
netfilter: ipset: fix address ranges at hash:*port* types
niu: Rename NIU parent platform device name to fix conflict.
r8169: fix a bug in rtl8169_init_phy()
bonding: fix a typo in a comment
ftmac100: use resource_size()
...
- add read/write functions for using this driver
also on powerpc plattforms
Signed-off-by: Heiko Schocher <hs@denx.de>
cc: linux-fbdev@vger.kernel.org
cc: devicetree-discuss@ozlabs.org
cc: Ben Dooks <ben@simtec.co.uk>
cc: Vincent Sanders <vince@simtec.co.uk>
cc: Samuel Ortiz <sameo@linux.intel.com>
cc: linux-kernel@vger.kernel.org
cc: Randy Dunlap <rdunlap@xenotime.net>
cc: Paul Mundt <lethal@linux-sh.org>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Alex Sidorenko reported for problems with local
routes left after IP addresses are deleted. It happens
when same IPs are used in more than one subnet for the
device.
Fix fib_del_ifaddr to restrict the checks for duplicate
local and broadcast addresses only to the IFAs that use
our primary IFA or another primary IFA with same address.
And we expect the prefsrc to be matched when the routes
are deleted because it is possible they to differ only by
prefsrc. This patch prevents local and broadcast routes
to be leaked until their primary IP is deleted finally
from the box.
As the secondary address promotion needs to delete
the routes for all secondaries that used the old primary IFA,
add option to ignore these secondaries from the checks and
to assume they are already deleted, so that we can safely
delete the route while these IFAs are still on the device list.
Reported-by: Alex Sidorenko <alexandre.sidorenko@hp.com>
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement compatibility with new hw_features for dev_disable_lro().
This is a transition path - dev_disable_lro() should be later
integrated into netdev_fix_features() after all drivers are converted.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remote used for TerraTec Cinergy T Stick RC.
Keytable from Martin Groszhauser <mgroszhauser@gmail.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Cc: Martin Groszhauser <mgroszhauser@gmail.com>
Cc: TerraTux <TerraTux@terratec.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Allow the MIPI-CSI data alignment to be defined in the board setup
as it may be different across various camera sensors.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add num_clients field to struct s5p_fimc_isp_info to define exactly
size of clients array which simplifies a bit the sensors management.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Pick an unused range of ioctls in Documentation/ioctl/ioctl-number.txt
and use it for the MEDIA_IOC_* ioctls.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add codes and documentation for the following media bus formats:
- V4L2_MBUS_FMT_SGBRG12_1X12
- V4L2_MBUS_FMT_SGRBG12_1X12
- V4L2_MBUS_FMT_SRGGB12_1X12
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add the following media bus format code definitions:
- V4L2_MBUS_FMT_SGRBG10_1X10 for 10-bit GRBG Bayer
- V4L2_MBUS_FMT_SGRBG10_DPCM8_1X8 for 10-bit DPCM compressed GRBG Bayer
- V4L2_MBUS_FMT_YUYV16_1X16 for 8-bit YUYV on 16-bit bus
- V4L2_MBUS_FMT_UYVY16_1X16 for 8-bit UYVY on 16-bit bus
- V4L2_MBUS_FMT_YVYU16_1X16 for 8-bit YVYU on 16-bit bus
- V4L2_MBUS_FMT_VYUY16_1X16 for 8-bit VYUY on 16-bit bus
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some buggy sensors generate corrupt frames when the stream is started.
This new operation return the number of corrupt frames to skip when
starting the stream.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds the VIDIOC_SUBDEV_S_CROP and G_CROP ioctls to the
userland API. CROPCAP is not implemented because it's redundant.
Signed-off-by: Antti Koskipaa <akoskipa@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The three new ioctl VIDIOC_SUBDEV_ENUM_FRAME_INTERVAL,
VIDIOC_SUBDEV_G_FRAME_INTERVAL and VIDIOC_SUBDEV_S_FRAME_INTERVAL can be
used to enumerate and configure a subdev's frame rate from userspace.
Two new video::g/s_frame_interval subdev operations are introduced to
support those ioctls. The existing video::g/s_parm operations are
deprecated and shouldn't be used anymore.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a userspace API to get, set and enumerate the media format on a
subdev pad.
The format at the output of a subdev usually depends on the format at
its input(s). The try format operation is thus not suitable for probing
format at individual pads, as it can't modify the device state and thus
can't remember the format tried at the input to compute the output
format.
To fix the problem, pass an extra argument to the get/set format
operations to select the 'try' or 'active' format.
The try format is used when probing the subdev. Setting the try format
must not change the device configuration but can store data for later
reuse. Data storage is provided at the file-handle level so applications
probing the subdev concurently won't interfere with each other.
The active format is used when configuring the subdev. It's identical to
the format handled by the usual get/set operations.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a v4l2_subdev_pad_ops structure for the operations that need to be
performed at the pad level such as format-related operations.
Pad format-related operations use v4l2_mbus_framefmt instead of
v4l2_format.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
V4L2 sub-devices store pad formats and crop settings in the file handle.
To let drivers initialize those settings properly, add an open operation
that is called when the subdev is opened as well as a corresponding
close operation.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Used for storing subdev information per file handle and hold V4L2 file
handle.
Signed-off-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Signed-off-by: Antti Koskipaa <akoskipa@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Adding new pixel codes at the end of the enumeration will soon create a
mess, so group the pixel codes by type and sort them by bus_width, bits
per component, samples per pixel and order of subsamples.
As the codes are part of the kernel ABI their value can't change when a
new code is inserted in the enumeration, so they are given an explicit
numerical value. When inserting a new pixel code developers must use and
update the next free value.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
For consistency with the V4L2_MBUS_FMT_Y10_1X10 format.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The v4l2_mbus_framefmt structure will be part of the public userspace
API and used (albeit indirectly) as an ioctl argument. As such, its size
must be fixed across userspace ABIs.
Replace the v4l2_field and v4l2_colorspace enums by __u32 fields and add
padding for future enhancements.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The header defines the v4l2_mbus_framefmt structure which will be used
by the V4L2 subdevs userspace API.
Change the type of the v4l2_mbus_framefmt::code field to __u32, as enum
sizes can differ between different ABIs on the same architectures.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
V4L2 subdevices are media entities. As such they need to inherit from
(include) the media_entity structure.
When registering/unregistering the subdevice, the media entity is
automatically registered/unregistered. The entity is acquired on device
open and released on device close.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
V4L2 devices are media entities. As such they need to inherit from
(include) the media_entity structure.
When registering/unregistering the device, the media entity is
automatically registered/unregistered. The entity is acquired on device
open and released on device close.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The pointer will later be used to register/unregister media entities
when registering/unregistering a v4l2_subdev or a video_device.
With the introduction of media devices, device drivers need to store a
pointer to a driver-specific structure in the device's drvdata.
v4l2_device can't claim ownership of the drvdata anymore.
To maintain compatibility with drivers that rely on v4l2_device storing
a pointer to itself in the device's drvdata, v4l2_device_register() will
keep doing so if the drvdata is NULL.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Drivers often need to associate pipeline objects to entities, and to
take stream state into account when configuring entities and links. The
pipeline API helps drivers manage that information.
When starting streaming, drivers call media_entity_pipeline_start(). The
function marks all entities connected to the given entity through
enabled links, either directly or indirectly, as streaming. Similarly,
when stopping the stream, drivers call media_entity_pipeline_stop().
The media_entity_pipeline_start() function takes a pointer to a media
pipeline and stores it in every entity in the graph. Drivers should
embed the media_pipeline structure in higher-level pipeline structures
and can then access the pipeline through the media_entity structure.
Link configuration will fail with -EBUSY by default if either end of the
link is a streaming entity, unless the link is marked with the
MEDIA_LNK_FL_DYNAMIC flag.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Create the following ioctl and implement it at the media device level to
setup links.
- MEDIA_IOC_SETUP_LINK: Modify the properties of a given link
The only property that can currently be modified is the ENABLED link
flag to enable/disable a link. Links marked with the IMMUTABLE link flag
can not be enabled or disabled.
Enabling or disabling a link has effects on entities' use count. Those
changes are automatically propagated through the graph.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Create the following two ioctls and implement them at the media device
level to enumerate entities, pads and links.
- MEDIA_IOC_ENUM_ENTITIES: Enumerate entities and their properties
- MEDIA_IOC_ENUM_LINKS: Enumerate all pads and links for a given entity
Entity IDs can be non-contiguous. Userspace applications should
enumerate entities using the MEDIA_ENT_ID_FLAG_NEXT flag. When the flag
is set in the entity ID, the MEDIA_IOC_ENUM_ENTITIES will return the
next entity with an ID bigger than the requested one.
Only forward links that originate at one of the entity's source pads are
returned during the enumeration process.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Create the following ioctl and implement it at the media device level to
query device information.
- MEDIA_IOC_DEVICE_INFO: Query media device information
The ioctl and its data structure are defined in the new kernel header
linux/media.h available to userspace applications.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Due to the wide differences between drivers regarding power management
needs, the media controller does not implement power management.
However, the media_entity structure includes a use_count field that
media drivers can use to track the number of users of every entity for
power management needs.
The use_count field is owned by media drivers and must not be touched by
entity drivers. Access to the field must be protected by the media
device graph_mutex lock.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add media entity graph traversal. The traversal follows enabled links by
depth first. Traversing graph backwards is prevented by comparing the next
possible entity in the graph with the previous one. Multiply connected
graphs are thus not supported.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Vimarsh Zutshi <vimarsh.zutshi@gmail.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As video hardware pipelines become increasingly complex and
configurable, the current hardware description through v4l2 subdevices
reaches its limits. In addition to enumerating and configuring
subdevices, video camera drivers need a way to discover and modify at
runtime how those subdevices are connected. This is done through new
elements called entities, pads and links.
An entity is a basic media hardware building block. It can correspond to
a large variety of logical blocks such as physical hardware devices
(CMOS sensor for instance), logical hardware devices (a building block
in a System-on-Chip image processing pipeline), DMA channels or physical
connectors.
A pad is a connection endpoint through which an entity can interact with
other entities. Data (not restricted to video) produced by an entity
flows from the entity's output to one or more entity inputs. Pads should
not be confused with physical pins at chip boundaries.
A link is a point-to-point oriented connection between two pads, either
on the same entity or on different entities. Data flows from a source
pad to a sink pad.
Links are stored in the source entity. To make backwards graph walk
faster, a copy of all links is also stored in the sink entity. The copy
is known as a backlink and is only used to help graph traversal.
The entity API is made of three functions:
- media_entity_init() initializes an entity. The caller must provide an
array of pads as well as an estimated number of links. The links array
is allocated dynamically and will be reallocated if it grows beyond the
initial estimate.
- media_entity_cleanup() frees resources allocated for an entity. It
must be called during the cleanup phase after unregistering the entity
and before freeing it.
- media_entity_create_link() creates a link between two entities. An
entry in the link array of each entity is allocated and stores pointers
to source and sink pads.
When a media device is unregistered, all its entities are unregistered
automatically.
The code is based on Hans Verkuil <hverkuil@xs4all.nl> initial work.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The media_device structure abstracts functions common to all kind of
media devices (v4l2, dvb, alsa, ...). It manages media entities and
offers a userspace API to discover and configure the media device
internal topology.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The media_devnode structure provides support for registering and
unregistering character devices using a dynamic major number. Reference
counting is handled internally, making device drivers easier to write
without having to solve the open/disconnect race condition issue over
and over again.
The code is based on video/v4l2-dev.c.
[mchehab@redhat.com: Remove linux/smp_lock.h include to not break compilation on bisect]
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
After the stack plugging introduction, these are called lockless.
Ensure that the counters are updated atomically.
Signed-off-by: Shaohua Li<shaohua.li@intel.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
This patch introduces lcdc->lcdcon_pol_negative which set CONTRAST_CTR
register to inverted polarity.
Signed-off-by: Andreas Bießmann <biessmann@corscience.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The AER error information printing support is implemented in
drivers/pci/pcie/aer/aer_print.c. So some string constants, functions
and macros definitions can be re-used without being exported.
The original PCIe AER error information printing function is not
re-used directly because the overall format is quite different. And
changing the original printing format may make some original users'
scripts broken.
Signed-off-by: Huang Ying <ying.huang@intel.com>
CC: Jesse Barnes <jbarnes@virtuousgeek.org>
CC: Zhang Yanmin <yanmin.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
APEI ERST firmware interface and implementation has no multiple users
in mind. For example, if there is four records in storage with ID: 1,
2, 3 and 4, if two ERST readers enumerate the records via
GET_NEXT_RECORD_ID as follow,
reader 1 reader 2
1
2
3
4
-1
-1
where -1 signals there is no more record ID.
Reader 1 has no chance to check record 2 and 4, while reader 2 has no
chance to check record 1 and 3. And any other GET_NEXT_RECORD_ID will
return -1, that is, other readers will has no chance to check any
record even they are not cleared by anyone.
This makes raw GET_NEXT_RECORD_ID not suitable for used by multiple
users.
To solve the issue, an in-memory ERST record ID cache is designed and
implemented. When enumerating record ID, the ID returned by
GET_NEXT_RECORD_ID is added into cache in addition to be returned to
caller. So other readers can check the cache to get all record ID
available.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Reviewed-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
- Add more ext4 tracepoints.
- Change ext4 tracepoints to use dev_t field with MAJOR/MINOR macros
so that we can save 4 bytes in the ring buffer on some platforms.
- Add sync_mode to ext4_da_writepages, ext4_da_write_pages, and
ext4_da_writepages_result tracepoints. Also remove for_reclaim
field from ext4_da_writepages since it is usually not very useful.
Signed-off-by: Jiaying Zhang <jiayingz@google.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
We dont need to test if we run from softirq context, we definitely are.
This saves few instructions in ip_rcv() & ip_rcv_finish()
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we're only doing a single write, and there are no other unstable
writes being queued up, we might want to just flip to using a stable
write RPC call.
Reviewed-by: NeilBrown <neilb@suse.de>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Provide v4l2_subdevs with v4l2_event support. Subdev drivers only need very
little to support events.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: David Cohen <dacohen@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The function isn't small or performance sensitive enough to be inlined.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Create a device node named subdevX for every registered subdev.
As the device node is registered before the subdev core::s_config
function is called, return -EGAIN on open until initialization
completes.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Vimarsh Zutshi <vimarsh.zutshi@gmail.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There's no reason to require subdevices to implement the core
operations. Remove the check for non-NULL core operations when
initializing the subdev.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
vb2_get_plane_payload() gets the bytesused field for a plane, it doesn't
set it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is the core of the WL1273 FM radio driver, it connects
the two child modules. The two child drivers are
drivers/media/radio/radio-wl1273.c and sound/soc/codecs/wl1273.c.
The radio-wl1273 driver implements the V4L2 interface and communicates
with the device. The ALSA codec offers digital audio, without it only
analog audio is available.
Signed-off-by: Matti J. Aaltonen <matti.j.aaltonen@nokia.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds audio DMA capture and ALSA mixer elements for the line
input jack of the Hauppauge Nova-S-plus DVB-S PCI card. The Nova-S-plus
has a WM8775 ADC that is currently not detected. This patch enables
this chip and exports volume, balance mute and ALC elements for ALSA
mixer controls.
[mchehab@redhat.com: Changed the patch to only talk with wm8775 if board
info says so. Also, added platform_data support, to avoid changing the
behaviour for other boards, and fixed CodingStyle]
[awalls@md.metrocast.net: Changed patch to make the WM8775_GID defintion
bridge driver private and let the bridge driver set the value of
v4l2_subdev.grp_id.]
--
To unsubscribe from this list: send the line "unsubscribe linux-media" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
It uses STAPL files and programs Altera FPGA through JTAG.
Interface to JTAG must be provided from main device module,
for example through cx23885 GPIO.
Signed-off-by: Igor M. Liplianin <liplianin@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This soc_camera driver is for Omnivision's OV9740 sensor. This initial
submission provides support for YUV422 output at 1280x720 (720p), which is
the sensor's native resolution. 640x480 (VGA) is also supported, with
cropping and scaling performed by the sensor's ISP.
This driver is heavily based off of the existing OV9640 driver.
Signed-off-by: Andrew Chew <achew@nvidia.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Extend soc-camera core to also support the videobuf2 API.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a function to calculate the number of samples on the media-bus,
required to retrieve one pixel of a certain format.
Signed-off-by: Alberto Panizzo <maramaopercheseimorto@gmail.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some ioctl's were defined wrong on 2.6.2 and 2.6.6, using the wrong
type of R/W arguments. They were fixed, but the old ioctl names are
still there, maintained to avoid breaking binary compatibility:
There's no sense on preserving those forever, as it is very doubtful
that someone would try to use a such old binary with a modern kernel.
Removing them will allow us to remove some magic done at the V4L ioctl
handler.
Note that any application compiled with a videodev2.h from 2.6.7 or later
will be using the correct ioctls.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
tda9887 used to use the T_STANDBY type internally, while tea5761
used it to put the device to sleep. Fix the code for it to work
properly with the tuner core changes and remove this flag from
tuner.h.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In the past, T_STANDBY were used on devices with a separate radio tuner to
mark a tuner that were disabled. With the time, it got newer meanings.
Also, due to a bug at the logic, the driver might incorrectly return
T_STANDBY to userspace.
So, instead of keeping the abuse, just use a boolean for storing
such information.
We can't remove T_STANDBY yet, as this is used on two other drivers. A
latter patch will address its usage outside tuner-core.
Thanks-to: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add I2C/V4L2 subdev driver for Siliconfile NOON010PC30 CIF camera.
The driver implements basic functionality, i.e. CIF/QCIF/QQCIF
resolution and color format selection, automatic/manual color
balance control. Other functions like cropping, rotation/flip,
exposure etc. can be easily implemented if needed.
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add ID for NOON010PC30 camera chip and reserve ID range for
Siliconfile sensors.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Manage the camera sensor clock in the host driver rather than
leaving this task for sensor drivers. The clock frequency
must be passed in the sensor's and host driver's platform data.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove bus_width from s5p_fimc_isp_info data structure.
Determine camera data bus width based on mediabus pixel format.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Change s3c_fimc.h header file name to s5p_fimc.h, replace s3c_fimc_*
names with s5p_fimc_*. s3c_fimc need to be reserved for S3C series
and s5p-fimc driver will not cover CAMIF devices in S3C SoC series.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add definitions for format with color planes non-contiguous
in physical memory. These formats apply only if the V4L2 multiplane
extension is used.
V4L2_PIX_FMT_NV12M - 2-plane Y/CbCr
V4L2_PIX_FMT_NV12MT - 2-plane Y/CbCr tiled (64x32 pixel macroblocks)
V4L2_PIX_FMT_YUV420M - 3-plane Y/Cb/Cr
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Port memory-to-memory framework to videobuf2 framework.
Add support for multi-planar Video for Linux 2 API extensions to the
memory-to-memory driver framework.
Based on the original patch written by Pawel Osciak.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a generic file io (read and write) emulator for videobuf2. It uses
MMAP memory type buffers and generic vb2 calls: req_bufs, qbuf and
dqbuf. Video date is being copied from mmap buffers to userspace with
standard copy_to_user() function. To add support for file io the driver
needs to provide an additional callback - read_setup or write_setup. It
should provide the default number of buffers used by emulator and flags.
With these flags one can detemine the style of read() or write()
emulation. By default 'streaming' style is used. With
VB2_FILEIO_READ_ONCE flag one can select 'one shot' mode for read()
emulator. With VB2_FILEIO_WRITE_IMMEDIATE flag one can select immediate
conversion of write calls to qbuf for write() emulator, so the vb2 will
not wait until each buffer is filled completely before queueing it to
the driver.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
CC: Pawel Osciak <pawel@osciak.com>
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add an implementation of DMA scatter/gather allocator and handling
routines for videobuf2.
For mmap operation mode it is implemented on top of
alloc_page + sg_set_page/_free_page.
For userptr operation mode it is implemented on top of
get_user_pages + sg_set_page/put_page.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
CC: Pawel Osciak <pawel@osciak.com>
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add an implementation of DMA coherent memory allocator and handling
routines for videobuf2, implemented on top of dma_alloc_coherent() call.
Signed-off-by: Pawel Osciak <p.osciak@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
CC: Pawel Osciak <pawel@osciak.com>
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add an implementation of contiguous virtual memory allocator and handling
routines for videobuf2, implemented on top of vmalloc()/vfree() calls.
Signed-off-by: Pawel Osciak <p.osciak@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
CC: Pawel Osciak <pawel@osciak.com>
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Videobuf2 is a Video for Linux 2 API-compatible driver framework for
multimedia devices. It acts as an intermediate layer between userspace
applications and device drivers. It also provides low-level, modular
memory management functions for drivers.
Videobuf2 eases driver development, reduces drivers' code size and aids in
proper and consistent implementation of V4L2 API in drivers.
Videobuf2 memory management backend is fully modular. This allows custom
memory management routines for devices and platforms with non-standard
memory management requirements to be plugged in, without changing the
high-level buffer management functions and API.
The framework provides:
- implementations of streaming I/O V4L2 ioctls and file operations
- high-level video buffer, video queue and state management functions
- video buffer memory allocation and management
Signed-off-by: Pawel Osciak <p.osciak@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
CC: Pawel Osciak <pawel@osciak.com>
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Multi-planar API is as a backwards-compatible extension of the V4L2 API,
which allows video buffers to consist of one or more planes. Planes are
separate memory buffers; each has its own mapping, backed by usually
separate physical memory buffers.
Many different uses for the multi-planar API are possible, examples
include:
- embedded devices requiring video components to be placed in physically
separate buffers, e.g. for Samsung S3C/S5P SoC series' video codec,
Y and interleaved Cb/Cr components reside in buffers in different
memory banks;
- applications may receive (or choose to store) video data of one video
buffer in separate memory buffers; such data would have to be temporarily
copied together into one buffer before passing it to a V4L2 device;
- applications or drivers may want to pass metadata related to a buffer and
it may not be possible to place it in the same buffer, together with video
data.
[mchehab@redhat.com: CodingStyle fixes]
Signed-off-by: Pawel Osciak <p.osciak@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch is adding support for Technisat's new USB2.0 DVB-S/S2 receiver
device. The development was sponsored by Technisat.
The Green led is toggle depending on the frontend-state. The Red LED is turned
on all the time.
The MAC address reading from the EEPROM along with the
LRC-method to check whether its valid.
Support for the IR-receiver of the Technisat USB2 box. The keys of
small, black remote-control are built-in, repeated key behaviour are
simulated.
The i2c-mutex of the dvb-usb-structure is used as a general mutex for
USB requests, as there are 3 threads racing for atomic requests
consisting of multiple usb-requests.
A module option is there which disables the toggling of LEDs by the
driver on certain triggers. Useful when being used in a "dark"
environment.
[mchehab@redhat.com: Fix merge conflicts with RC renaming patches]
Signed-off-by: Martin Wilks <m.wilks@technisat.com>
Signed-off-by: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
hwmon: (ads1015) Make gain and datarate configurable
hwmon: (ads1015) Drop dynamic attribute group
hwmon: Add support for Texas Instruments ADS1015
hwmon: New driver for SMSC SCH5627
hwmon: (abituguru*) Update my email address
hwmon: (lm75) Speed up detection
hwmon: (lm75) Add detection of the National Semiconductor LM75A
hp_accel: Fix driver name
Move lis3lv02d drivers to drivers/misc
Move hp_accel to drivers/platform/x86
Let Kconfig handle lis3lv02d dependencies
hwmon: (sht15) Fix integer overflow in humidity calculation
hwmon: (sht15) Spelling fix
hwmon: (w83795) Document pin mapping
This updates the common header files used by the different ceph
related modules. Specifically it adds definitions required by
the rbd watch/notify feature.
Signed-off-by: Yehuda Sadeh <yehuda@hq.newdream.net>
If we send a request to osd A, and the request's pg remaps to osd B and
then back to A in quick succession, we need to resend the request to A. The
old code was only calling kick_requests after processing all incremental
maps in a message, so it was very possible to not resend a request that
needed to be resent. This would make the osd eventually time out (at least
with the current default of osd timeouts enabled).
The correct approach is to scan requests on every map incremental. This
patch refactors the kick code in a few ways:
- all requests are either on req_lru (in flight), req_unsent (ready to
send), or req_notarget (currently map to no up osd)
- mapping always done by map_request (previous map_osds)
- if the mapping changes, we requeue. requests are resent only after all
map incrementals are processed.
- some osd reset code is moved out of kick_requests into a separate
function
- the "kick this osd" functionality is moved to kick_osd_requests, as it
is unrelated to scanning for request->pg->osd mapping changes
Signed-off-by: Sage Weil <sage@newdream.net>
Fix many of each of these warnings:
Warning(include/net/cfg80211.h:519): No description found for parameter 'rxrate'
Warning(include/net/mac80211.h:1163): bad line:
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6:
FS: lookup_mnt() is only used in the core fs routines now
bfs: fix bitmap size argument to find_first_zero_bit()
fs: Use BUG_ON(!mnt) at dentry_open().
fs: devpts_pty_new() return -ENOMEM if dentry allocation failed
nfs: lock() vs unlock() typo
pstore: fix leaking ->i_private
introduce sys_syncfs to sync a single file system
Small typo fix...
Filesystem: fifo: Fixed coding style issue.
fs/inode: Fix kernel-doc format for inode_init_owner
select: remove unused MAX_SELECT_SECONDS
vfs: cleanup do_vfs_ioctl()
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
firewire: core: ignore link-active bit of new nodes, fix device recognition
firewire: sbp2: revert obsolete 'fix stall with "Unsolicited response"'
firewire: core: increase default SPLIT_TIMEOUT value
firewire: ohci: Misleading kfree in ohci.c::pci_probe/remove
firewire: ohci: omit IntEvent.busReset check rom AT queueing
firewire: ohci: prevent starting of iso contexts with empty queue
firewire: ohci: prevent iso completion callbacks after context stop
firewire: core: rename some variables
firewire: nosy: should work on Power Mac G4 PCI too
firewire: core: fix card->reset_jiffies overflow
firewire: cdev: remove unneeded reference
firewire: cdev: always wait for outbound transactions to complete
firewire: cdev: remove unneeded idr_find() from complete_transaction()
firewire: ohci: log dead DMA contexts
Configuration for ads1015 gain and datarate is possible via
devicetree or platform data.
This is a followup patch to previous ads1015 patches on Jean Delvares
tree.
Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
v3 -> v2: Moved ASPM enabling logic to pci_set_power_state()
v2 -> v1: Preserved the logic in pci_raw_set_power_state()
: Added ASPM enabling logic after scanning Root Bridge
: http://marc.info/?l=linux-pci&m=130046996216391&w=2
v1 : http://marc.info/?l=linux-pci&m=130013164703283&w=2
The assumption made in commit 41cd766b06
(PCI: Don't enable aspm before drivers have had a chance to veto it) that
pci_enable_device() will result in re-configuring ASPM when aspm_policy is
POWERSAVE is no longer valid. This is due to commit
97c145f7c8 (PCI: read current power state
at enable time) which resets dev->current_state to D0. Due to this the
call to pcie_aspm_pm_state_change() is never made. Note the equality check
(below) that returns early:
./drivers/pci/pci.c: pci_raw_set_pci_power_state()
546 /* Check if we're already there */
547 if (dev->current_state == state)
548 return 0;
Therefore OSPM never configures the PCIe links for ASPM to turn them "on".
Fix it by configuring ASPM from the pci_enable_device() code path. This
also allows a driver such as the e1000e networking driver a chance to
disable ASPM (L0s, L1), if need be, prior to enabling the device. A
driver may perform this action if the device is known to mis-behave
wrt ASPM.
Signed-off-by: Naga Chumbalkar <nagananda.chumbalkar@hp.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
We need to distinguish the situation in which ASPM support is
disabled from the command line or through .config from the situation
in which it is disabled, because the hardware or BIOS can't handle
it. In the former case we should not report ASPM support to the BIOS
through ACPI _OSC, but in the latter case we should do that.
Introduce pcie_aspm_support_enabled() that can be used by
acpi_pci_root_add() to determine whether or not it should report ASPM
support to the BIOS through _OSC.
Cc: stable@kernel.org
References: https://bugzilla.kernel.org/show_bug.cgi?id=29722
References: https://bugzilla.kernel.org/show_bug.cgi?id=20232
Reported-and-tested-by: Ortwin Glück <odi@odi.ch>
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Tested-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
lookup_mnt() is only used in the core fs routines now, so it doesn't need to
be globally declared anymore. It isn't exported to modules at the moment, so
nothing that can be modularised seems to be using it.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
One of the disadvantages of on-stack plugging is that we potentially
lose out on merging since all pending IO isn't always visible to
everybody. When we flush the on-stack plugs, right now we don't do
any checks to see if potential merge candidates could be utilized.
Correct this by adding a new insert variant, ELEVATOR_INSERT_SORT_MERGE.
It works just ELEVATOR_INSERT_SORT, but first checks whether we can
merge with an existing request before doing the insertion (if we fail
merging).
This fixes a regression with multiple processes issuing IO that
can be merged.
Thanks to Shaohua Li <shaohua.li@intel.com> for testing and fixing
an accounting bug.
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
This patch moves the platform data definition from
arch/arm/plat-pxa/include/plat/i2c.h to include/linux/i2c/pxa-i2c.h so
it can be accessed from x86 the same way as on ARM.
This change should make no functional change to the PXA code. The move
is verified by building the following defconfigs:
cm_x2xx_defconfig corgi_defconfig em_x270_defconfig ezx_defconfig
imote2_defconfig pxa3xx_defconfig spitz_defconfig zeus_defconfig
raumfeld_defconfig magician_defconfig mmp2_defconfig pxa168_defconfig
pxa910_defconfig
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Dirk Brandewie <dirk.brandewie@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
It is frequently useful to sync a single file system, instead of all
mounted file systems via sync(2):
- On machines with many mounts, it is not at all uncommon for some of
them to hang (e.g. unresponsive NFS server). sync(2) will get stuck on
those and may never get to the one you do care about (e.g., /).
- Some applications write lots of data to the file system and then
want to make sure it is flushed to disk. Calling fsync(2) on each
file introduces unnecessary ordering constraints that result in a large
amount of sub-optimal writeback/flush/commit behavior by the file
system.
There are currently two ways (that I know of) to sync a single super_block:
- BLKFLSBUF ioctl on the block device: That also invalidates the bdev
mapping, which isn't usually desirable, and doesn't work for non-block
file systems.
- 'mount -o remount,rw' will call sync_filesystem as an artifact of the
current implemention. Relying on this little-known side effect for
something like data safety sounds foolish.
Both of these approaches require root privileges, which some applications
do not have (nor should they need?) given that sync(2) is an unprivileged
operation.
This patch introduces a new system call syncfs(2) that takes an fd and
syncs only the file system it references. Maybe someday we can
$ sync /some/path
and not get
sync: ignoring all arguments
The syscall is motivated by comments by Al and Christoph at the last LSF.
syncfs(2) seems like an appropriate name given statfs(2).
A similar ioctl was also proposed a while back, see
http://marc.info/?l=linux-fsdevel&m=127970513829285&w=2
Signed-off-by: Sage Weil <sage@newdream.net>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Add fields needed for the copy-on-write ext4 development work.
The h_cowing flag is used by ext4 snapshots code to mark the task in
COWING state.
The h_XXX_credits fields are used to track buffer credits usage
(accounted by COW and non-COW operations).
The h_cow_XXX fields are used as per task debugging counters.
Merging this commit into mainline will allow users to test ext4
snapshots as a standalone module, without the need to patch and
install a development kernel.
Signed-off-by: Amir Goldstein <amir73il@users.sf.net>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
* 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
i2c-i801: SMBus patch for Intel DH89xxCC DeviceIDs
i2c: Drop i2c_adapter.id
i2c: Deprecate i2c_driver.attach_adapter and .detach_adapter
i2c-dev: Use standard bus notification mechanism
i2c: Export i2c_for_each_dev
i2c: Get rid of <linux/i2c-id.h>
i2c: Minor fixes to upgrading-clients document
i2c: make i2c_get_adapter prototype clearer
i2c: Fix typo in instantiating-devices document
i2c-boardinfo: Fix typo in comment
The b_cow_tid field will be used by the ext4 snapshots code to store
the transaction id when the buffer was last cowed.
Merging this patch to mainline will allow users to test ext4 snapshots
as a standalone module, without the need to patch and install a
development kernel.
On 64bit machines this field uses fills in a padding "hole" and does
not increase the size of the struct. On a 32bit machine this patch
increases the size of the struct from 60 to 64 bytes.
Signed-off-by: Amir Goldstein <amir73il@users.sf.net>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Below is a patch against drm-next branch of 2.6.38-rc8+ kernel that adds
the capability to wait on vblank events for CRTCs that are greater than 1
and thus cannot be represented with primary/secondary flags in the legacy
interface. It was discussed on the dri-devel list in these two threads:
http://lists.freedesktop.org/archives/dri-devel/2011-March/009009.htmlhttp://lists.freedesktop.org/archives/dri-devel/2011-March/009025.html
This patch extends the interface to drm_wait_vblank ioctl so that crtc>1
can be represented. It also adds a new capability to drm_getcap ioctl so
that the user space can check whether the new interface to drm_wait_vblank
is supported (and fall back to the legacy interface if not)
Signed-off-by: Ilija Hadzic <ihadzic@research.bell-labs.com>
Reviewed-by: Mario Kleiner <mario.kleiner at tuebingen.mpg.de>
Acked-by: Mario Kleiner <mario.kleiner at tuebingen.mpg.de>
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Tested-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Johannes Weiner