Add DT data for OMAP4 Pandaboard. The board has the following displays:
dvi: uses TFP410 encoder to convert DPI to DVI
hdmi: OMAP HDMI output with TPD12S015 ESD/level shifter
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
The necessary clock phandle for the EHCI clock is now provided
via device tree so we no longer need this legacy method.
Update the omap4-panda and omap5-uevm board DTS to provide the
necessary EHCI PHY clock information.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
All audio nodes has been set to disabled state in omap4.dtsi file.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Attach the pinctrl nodes to their respective device node:
mcbsp1, mcpdm and twl6040.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
pin mux wl12xx_gpio and wl12xx_pins should be part of omap4_pmx_core
and not omap4_pmx_wkup. So, move wl12xx_* to omap4_pmx_core.
Fix the following error message:
pinctrl-single 4a31e040.pinmux: mux offset out of range: 0x38 (0x38)
pinctrl-single 4a31e040.pinmux: could not add functions for pinmux_wl12xx_pins 56x
SDIO card is not detected after moving pin mux to omap4_pmx_core since
sdmmc5_clk pull is disabled. Enable Pull up on sdmmc5_clk to detect SDIO card.
This fixes a regression where WLAN did not work after a warm reset
or after one up/down cycle that happened when we move omap4 to boot
using device tree only. For reference, the kernel bug is described at:
https://bugzilla.kernel.org/show_bug.cgi?id=63821
Cc: stable@vger.kernel.org # v3.10+
Signed-off-by: Balaji T K <balajitk@ti.com>
[tony@atomide.com: update comments to describe the regression]
Signed-off-by: Tony Lindgren <tony@atomide.com>
New u-boot versions no longer set the pinmuxing for Panda's DPI output,
and the muxing has to be done in the .dts file.
Add pinmuxing for DPI and TFP410. Without these, the DVI output on Panda
does not work with recent u-boot.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We no longer need to model the RESET line as a regulator since
the USB phy-nop driver accepts "reset-gpios" property.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
The OMAP4 SoC family uses specially-designed PMIC (power management IC)
companion chip for power management needs: TWL6030/TWL6032.
Therefore there is a typical connection of PMIC to OMAP4 so we can
move it into separate .dtsi file and do not duplicate over
board-specific files.
Tested on OMAP4 SDP board and Pandaboard ES2.
Signed-off-by: Ruslan Bilovol <ruslan.bilovol@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Commit b42b9181 (ARM: OMAP2+: Remove board-omap4panda.c)
removed legacy booting in favor of device tree based booting
for pandaboard. That caused the WLAN to stop working as the
related .dts entries fell through the cracks.
The legacy muxing was setting pulls for GPIO 48 and 49, so let's
keep that behaviour for now to avoid further regressions for
BT and FM. Also input logic was enabled for MMC CLK line, but
I've verified that the input logic we don't need enabled for
CLK line as it's not bidirectional.
Also, we want to use non-removable instead of ti,non-removable
as the ti,non-removable also sets no_regulator_off_init which
is really not what we want as then wl12xx won't get powered
up and down which is needed for resetting it.
Note that looks like the WLAN interface fails to come up after
a warm reset, but that most likely was also happening with
the legacy booting and needs a separate fix.
Cc: Paolo Pisati <p.pisati@gmail.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Luciano Coelho <luca@coelho.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
On Panda the +5V supply for DVI EDID is supplied by the
same regulator that poweres the USB Hub. Currently, the
DSS/DVI subsystem doesn't know how to manage this regulator
and so DVI EDID reads will fail if USB Hub is not enabled.
As a temporary fix we keep this regulator permanently enabled
on boot. This fixes the DVI EDID read problem.
CC: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Provide the RESET and Power regulators for the USB PHY,
the USB Host port mode and the PHY device.
Also provide pin multiplexer information for the USB host
pins.
HACK: The reset control need to be replaced with the proper
gpio-controlled reset driver as soon it will be merged [1].
[1] http://thread.gmane.org/gmane.linux.drivers.devicetree/36830
Signed-off-by: Roger Quadros <rogerq@ti.com>
[benoit.cousson@linaro.org: Add disclaimer about the reset control
inside changelog and code]
Cc: Florian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Update the dt property ti,audpwron-gpio to use the
gpio macro definition for GPIO_ACTIVE_HIGH.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Florian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
The GPIO for LED D1 on the omap4-panda a1-a3 rev and the omap4-panda-es
are different.
A1-A3 = gpio_wk7
ES = gpio_110
There is no change to LED D2
Abstract away the pinmux and the LED definitions for the two boards into
the respective DTS files.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Using constants for pinctrl allows a better readability, and removes
redundancy with comments.
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Use the constants defined in include/dt-bindings/interrupt-controller/
to enhance readability.
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Use standard GPIO constants to enhance the readability of DT GPIOs.
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Replace /include/ by #include for OMAP2+ DT, in order to use the
C pre-processor, making use of #define features possible.
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Earlier commits ensured proper muxing of pins related to proper
TWL6030 behavior: see commit 265a2bc8 (ARM: OMAP3: TWL4030: ensure
sys_nirq1 is mux'd and wakeup enabled) and commit 1ef43369 (ARM:
OMAP4: TWL: mux sys_drm_msecure as output for PMIC).
However these only fixed legacy boot and not DT boot. For DT boot,
the default mux values need to be set properly in DT.
Special thanks to Nishanth Menon for the review and catching some
major flaws in earlier versions.
Tested on OMAP4430/Panda and OMAP4460/Panda-ES.
Cc: Nishanth Menon <nm@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Acked-by: Grygorii Strashko <grygorii.strashko@ti.com>
[benoit.cousson@linaro.org: Slightly change the subject to align
board name with file name]
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
PandaBoard, PandaBoard-A4 revisions use OMAP4430.
PandaBoard-ES version of the board uses OMAP4460.
Move the original panda dts file into a common dtsi used by all panda
variants. This allows us to introduce SoC variation for PandaBoard ES
without impacting other PandaBoard versions that are supported.
As part of this change, since OMAP4460 adds on to OMAP4430, add
omap4.dtsi to omap4460.dtsi.
Signed-off-by: Nishanth Menon <nm@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Jon Hunter <jon-hunter@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Keerthy <j-keerthy@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Tomi Valkeinen