The driver for the PCIe controller was just added, this adds the
missing definition of the IRQ numbers to device tree. The driver itself
will be automatically detected by bcma.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This adds the NAND flash chip description for a standard chip found
connected to this SoC. This makes use of generic Broadcom NAND driver
with the iProc interface.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
When dma-coherent transfers are enabled, the mmap call must
not change the pg_prot flags in the vma struct.
Split the arm_dma_mmap into a common and specific parts,
and add a "arm_coherent_dma_mmap" implementation that does
not alter the page protection flags.
Tested on a topic-miami board (Zynq) using the ACP port
to transfer data between FPGA and CPU using the Dyplo
framework. Without this patch, byte-wise access to mmapped
coherent DMA memory was about 20x slower because of the
memory being marked as non-cacheable, and transfer speeds
would not exceed 240MB/s.
After this patch, the mapped memory is cacheable and the
transfer speed is again 600MB/s (limited by the FPGA) when
the data is in the L2 cache, while data integrity is being
maintained.
The patch has no effect on non-coherent DMA.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fixes the TCM initialisation code to handle TCM banks that are
present but inaccessible due to TrustZone configuration. This is
the default case when enabling the non-secure world. It may also
be the case that that the user decided to use TCM for TrustZone.
This change has exposed a bug in handling of TCM where no TCM bank
was usable (the 0 size TCM case). This change addresses the
resulting hang.
This code only handles the ARMv6 TCMTR register format, and will not
work correctly on boards that use the ARMv7 (or any other) format.
This is handled by performing an early exit from the initialisation
function when the TCMTR reports any format other than v6.
Signed-off-by: Michael van der Westhuizen <michael@smart-africa.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When using a toolchain with gold as the default linker, the VDSO build
fails:
VDSO arch/arm/vdso/vdso.so.raw
HOSTCC arch/arm/vdso/vdsomunge
MUNGE arch/arm/vdso/vdso.so.dbg
OBJCOPY arch/arm/vdso/vdso.so
BFD: arch/arm/vdso/vdso.so: Not enough room for program headers, try
linking with -N
For whatever reason, ld.gold is omitting an exidx program header that
ld.bfd emits, and even when I work around that, I don't get a working
VDSO.
For now, instead of supporting gold (which will fail to link the
kernel anyway since it does not implement --pic-veneer), direct the
compiler to use the traditional bfd linker. This is accomplished by
using -fuse-ld, which is implemented in GCC 4.8 and later.
Note: one limitation of this is that if the toolchain is configured
to use gold by default, and the bfd linker is not in $PATH, the VDSO
build will fail:
VDSO arch/arm/vdso/vdso.so.raw
collect2: fatal error: cannot find 'ld'
This will happen if CROSS_COMPILE begins with a path such as
/opt/bin/arm-linux-gnu- but /opt/bin is not in $PATH. This is
considered an acceptable corner-case limitation and is easily worked
around.
Additonal note: we use cc-option instead of cc-ldoption so that
-fuse-ld=bfd is placed in the command line if the compiler recognizes
the option. Using cc-ldoption results in an attempt to link, which
fails in the situation just described, causing -fuse-ld=bfd to be
omitted and gold to be used for the VDSO link, which is what we're
trying to prevent.
Reported-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Nathan Lynch <nathan_lynch@mentor.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Currently the VDSO's link options are kind of a mess spread between
ccflags-y and cmd_vdsold. Collect linker directives into one
variable, VDSO_LDFLAGS, and use that in cmd_vdsold.
Signed-off-by: Nathan Lynch <nathan_lynch@mentor.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There's quite a lot here, most of it from Mark Rutland, who has been
working on big.LITTLE PMU support for a while now. His work also brings
us significantly closer to moving the bulk of the CPU PMU driver out
into drivers/, where it can be shared with arm64.
As part of this work, there is a small patch to perf/core, which has
been Acked-by PeterZ and doesn't conflict with tip/perf/core at present.
I've kept that patch on a separate branch, merged in here, so that the
tip guys can pull it too if any unexpected issues crop up.
Please note that there is a conflict with mainline, since we remove
perf_event_cpu.c. The correct resolution is also to remove the file,
since the changes there are already reflected in the rework (and this
resolution is already included in linux-next).
SYSMMU devices are registered very early in arch_initcall, so ensure
that they can get access to power domains by registering power domain
driver from earlier initcall. This change requires dropping usage of
the platform device associated with each power domain and replacing
clock calls with respective of_clk_* equivalents.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
PS_HOLD based power off procedure is common for all Exynos SoCs,
so use it for every Exynos SoCs.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The platform_device_id is not modified by the driver and core
uses it as const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The irq_domain_ops are not modified by the driver and the irqdomain
core code accepts pointer to a const data.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The following patch adds coupled cpuidle support for Exynos3250 to
an existing cpuidle-exynos driver. As a result it enables AFTR mode
to be used by default on Exynos3250 without the need to hot unplug
CPU1 first.
The detailed changelog:
- use exynos_[get,set]_boot_addr() in cpuidle-exynos.c and then make
cpu_boot_reg_base() static
- use exynos_core_restart() in exynos_cpu0_enter_aftr()
- add missing smp_rmb() to exynos_cpu0_enter_aftr() (to make the code
in-sync with the platform SMP code)
- add call_firmware_op(cpu_boot, 1) to exynos_cpu0_enter_aftr()
- use dsb_sev() instead of IPI wakeup for Exynos3250 in
exynos_cpu0_enter_aftr()
- add CPU0 vs CPU1 synchronization based on S5P_PMU_SPARE2 register
for Exynos3250 to cpuidle-exynos.c
- add flush_cache_all() for CPU1/0 before powerdown/AFTR for
Exynos3250 to exynos_wfi_finisher()/exynos_do_idle()
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Add get_cpu_boot_addr() firmware operation and then
exynos_get_boot_addr() helper.
This is a preparation for adding coupled cpuidle support
for Exynos3250 SoC.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Add exynos_set_boot_addr() helper and covert existing code
(exynos_boot_secondary() and exynos_smp_prepare_cpus()) to
use it.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
There is a kernel message about secondary CPU bootup when
exynos_core_restart() is called through CPU hotplug code-path (the
only exynos_core_restart() user currently) so there is no need for
an extra info on Exynos3250 SoC about software reset. This also
prepares exynos_core_restart() to be re-used in coupled cpuidle
code-path in the future.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
exynos_boot_secondary() can erroneously return 0 or -ENOSYS even
when waiting on pen_release being set to -1 timeouts. Fix it by
adjusting ret variable value to -ETIMEDOUT when necessary.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Using a fixed (by DTS) parent for clocks when turning on the power
domain may introduce issues in other drivers. For example when such
driver changes the parent during runtime and expects that he is the
only place of such change.
Do not rely on DTS providing the fixed parent for such clocks. Instead
before switching domain off, grab a current parent of a clock with
clk_get_parent().
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Convert clk_enable/clk_disable to clk_prepare_enable/clk_disable_unprepare
calls as required by common clock framework. Removes this warning on probe:
------------[ cut here ]------------
WARNING: CPU: 0 PID: 1 at drivers/clk/clk.c:889 __clk_enable+0x28/0x9c()
Modules linked in:
CPU: 0 PID: 1 Comm: swapper Not tainted 3.19.0+ #46
[<c0013a98>] (unwind_backtrace) from [<c0010d8c>] (show_stack+0x10/0x14)
[<c0010d8c>] (show_stack) from [<c001b018>] (warn_slowpath_common+0x7c/0xa4)
[<c001b018>] (warn_slowpath_common) from [<c001b0d0>] (warn_slowpath_null+0x18/0x20)
[<c001b0d0>] (warn_slowpath_null) from [<c01a5f80>] (__clk_enable+0x28/0x9c)
[<c01a5f80>] (__clk_enable) from [<c01a600c>] (clk_enable+0x18/0x2c)
[<c01a600c>] (clk_enable) from [<c001860c>] (s3c_adc_probe+0x11c/0x18c)
[<c001860c>] (s3c_adc_probe) from [<c0153a10>] (platform_drv_probe+0x30/0x78)
[<c0153a10>] (platform_drv_probe) from [<c01523e0>] (driver_probe_device+0xb0/0x1fc)
[<c01523e0>] (driver_probe_device) from [<c01525dc>] (__driver_attach+0x68/0x88)
[<c01525dc>] (__driver_attach) from [<c0150df0>] (bus_for_each_dev+0x70/0x94)
[<c0150df0>] (bus_for_each_dev) from [<c0151c80>] (bus_add_driver+0xdc/0x1c4)
[<c0151c80>] (bus_add_driver) from [<c0152ba4>] (driver_register+0x9c/0xe0)
[<c0152ba4>] (driver_register) from [<c03041cc>] (adc_init+0x10/0x34)
[<c03041cc>] (adc_init) from [<c00087fc>] (do_one_initcall+0x110/0x1cc)
[<c00087fc>] (do_one_initcall) from [<c02ffccc>] (kernel_init_freeable+0xf4/0x1ac)
[<c02ffccc>] (kernel_init_freeable) from [<c022f4fc>] (kernel_init+0x8/0xe0)
[<c022f4fc>] (kernel_init) from [<c000e098>] (ret_from_fork+0x14/0x3c)
---[ end trace f4a1ea39a114fecf ]---
Signed-off-by: Sergiy Kibrik <sakib@meta.ua>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Add missing of_node_put() to:
1. Error return path if allocating memory for exynos_pm_domain failed.
2. Second iteration over power domains if a child domain was not
present or was incomplete.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reported-by: Karol Wrona <k.wrona@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Prevent possible NULL pointer dereference of pointer returned by
of_find_device_by_node(). Handle this by skipping such power domain.
Additionally fail the init on kstrdup() failure. Such case is actually
not fatal because the name for power domain allocated by kstrdup() is
used only in printk. Still as a precaution handle this as an error
condition.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Prevent possible NULL pointer dereference if of_iomap() fails.
Handle the error by skipping such power domain.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Use stdout-path to specify the console and remove the console argument from
the kernel command line.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Use stdout-path to specify the console and remove the console argument from
the kernel command line.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Use stdout-path to specify the console and remove the bootargs.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Use stdout-path to specify the console and remove the console argument from
the kernel command line.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Use stdout-path to specify the console and remove the console argument from
the kernel command line.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Use stdout-path to specify the console and remove the console argument from
the kernel command line.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Use stdout-path to specify the console and remove the console argument from
the kernel command line.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Use stdout-path to specify the console and remove the console argument from
the kernel command line.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Use stdout-path to specify the console and remove the console argument from
the kernel command line.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Use stdout-path to specify the console and remove the console argument from
the kernel command line.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Use stdout-path to specify the console and remove the console argument from
the kernel command line.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Use stdout-path to specify the console.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
The kizbox dts are using the deprecated linux,stdout-path. Replace those by
stdout-path.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Gaël PORTAY <g.portay@overkiz.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Add RTC support to the at91sam9rlek.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
The RTC lives at 0xfffffe00. Also reorder the node properly.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
AM57xx Beagle X15 has a HDMI output. This patch adds the device tree
nodes required for HDMI.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: devicetree@vger.kernel.org
Acked-by: Tony Lindgren <tony@atomide.com>
DRA72 EVM has a HDMI output. This patch adds the device tree nodes
required for HDMI.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: devicetree@vger.kernel.org
Acked-by: Tony Lindgren <tony@atomide.com>
DRA7xxx contains a very similar DSS to OMAP5. The main differences are:
* no DSI or RFBI support.
* 1 or 2 dedicated video PLLs.
* need to do additional configuration to the DRA7 CONTROL module.
DRA72xx has only one video PLL, and DRA74xx has two.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: devicetree@vger.kernel.org
Acked-by: Tony Lindgren <tony@atomide.com>
Simplify the DSS detection logic by creating a list of the omapdss
compat strings, instead of checking each separately with an 'if'.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Set DSS core hwmod as the parent for all the DSS submodules. This
ensures that the parent hwmods are enabled before any DSS submodules are
accessed.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Add DMM hwmod entries for DRA7. This is identical to DMM on OMAP5.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
We need set-rate-parent flags for the display's clock path so that the
DSS driver can change the clock rate of the PLL.
This patchs adds the ti,set-rate-parent flag to 'dss_dss_clk' clock
node, which is only a gate clock, allowing the setting of the clock rate
to propagate to the PLL.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: devicetree@vger.kernel.org
Acked-by: Tero Kristo <t-kristo@ti.com>
This patch adds System MMU nodes to all defined devices that are
specific to Exynos5420/5800/5422 series.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
This patch adds System MMU nodes to all defined devices that are
specific to Exynos5250 series.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
This patch adds System MMU nodes to all defined devices that are
specific to Exynos4415 series.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
This patch adds System MMU nodes to the devices that are specific to
Exynos3250 series.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
This patch adds System MMU nodes that are specific to Exynos4210/4x12
series.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Add a new Linux clock for DRA7 based SoCs to control DESHDCP clock.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
The i.MX6DL/S GPT has a different programming model from i.MX6Q one.
Add the compatible string "fsl,imx6dl-gpt" for it, and leave
"fsl,imx6q-gpt" there to keep the existing/old kernel happy.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This patch adds support for the imx6dl based aristainetos2 board
with following configuration:
CPU: Freescale i.MX6DL rev1.1 at 792 MHz
MReset cause: POR
MBoard: aristaitenos2
DRAM: 1 GiB
NAND: 1024 MiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
SF: Detected N25Q128A with page size 256 Bytes, erase size 64 KiB, total 16 MiB
Display: lb07wv8 (800x480)
As this board can be used with 2 different display types, the
differences between them are extracted into 2 DTS files, and
the common settings are collected in a common file.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Arrange the license text a bit to make it clear.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Also add label for backlight_lvds and connect it to the LVDS display.
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Also add label for backlight_lvds and connect it to the display.
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
imx7d intergrates the unique display controller for EPD panel, pixel engines
and graphics engines to make it a ideal solution for EPD based devices such
as eReader, Signage, as well as any application rely on the bistable charactersic
of the EPD panel.
imx7d include two ARM Cortex A7 Core and one Cortex-M4 core.
Included Main Peripheral
- DDR3\LP-DDR2
- GPMI\BCH\APBH DMA(NAND flash support)
- QSPI
- WEIM Nor
- LCDIF\MIPI DSI
- CSI\MIPI CSI
- EPDC
- PCIe RC\EP
- USB OTG\Host
- CAN x2
- I2C x4
- SIMv2 x2
- ENET -x2
- uSDHC x3
- eCSPI x1
- PWM x4
- OCOTP (fuse)
- GPT x4
- WDOG x4
- Flex Timer x2
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This commit includes a minor nomenclature fixup for boards based on the
Freescale VF610 SoC and which make use of the alternate "RMII1_RXD1"
functionality for pin PTC12. This brings the macro name in-line with
both the datasheet and other similar macros.
Signed-off-by: Cory Tusar <cory.tusar@pid1solutions.com>
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add DT support for the Broadcom Wifi/Bluetooth devices found on the
microsom board.
[Modified original Russell King's patch to use mmc-pwrseq]
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Jon Nettleton <jon@solid-run.com>
Tested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The CODA960 VPU is part of the PU power domain. Add power-domains
phandle so it can be associated with the PU generic pm domain for
power gating.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add support for the Gateworks GW5510 board featuring:
* i.MX6 SoC
* up to 512MB DDR3
* up to 2GB NAND flash
* 1x miniPCIe socket (with USB)
* HDMI out (micro-HDMI)
* HDMI in (micro-HDMI) (currently supported by only vendor kernel)
* TTL level I/O (supported by GW16111 breakout board):
* I2C
* 2x UART
* CAN
* 2x DIO (GPIO/PWM)
* USB OTG
For more details see:
http://www.gateworks.com/product/item/ventana-gw5510-single-board-computer
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
USBOTG1 always work on peripheral mode and USBOTG in host mode, so fix
their roles accordingly.
Tested by mounting the MMC card as a storage device:
modprobe g_mass_storage file=/dev/mmcblk0p2
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
According to the warp schematics there are no regulators for the USB OTG
ports, so let's remove them.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The 'reg_1p8v' regulator is not used anywhere, so let's remove it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This patch updates the in tree-users of the SSD1306 controller for using
the newly introduced DT properties.
Signed-off-by: Thomas Niederprüm <niederp@physik.uni-kl.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add PCIe support. Based on a patch from Rabeeh Khoury from the solid-run
tree.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The imx23-olinuxino board has an i2c interface exposed on UEXT connector.
This patch enables i2c and selects the pin group used on UEXT connector.
Tested with MOD-LCD1x9 from Olimex.
This patch is based on work by Fadil Berisha with his permission. However
all bugs are mine.
Signed-off-by: Harald Geyer <harald@ccbib.org>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The imx23-olinuxino board has an i2c interface exposed on UEXT connector.
This patch provides the generic devicetree infrastructure for a follow-up
patch to add support to the actual board files.
Tested all three possible pin groups with MOD-LCD1x9 from Olimex.
This patch is based on work by Fadil Berisha with his permission. However
all bugs are mine.
Signed-off-by: Harald Geyer <harald@ccbib.org>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
imx6qdl-hummingboard boards use sgtl5000 codec and the machine file
(imx-sgtl5000) already sets SSI in slave mode and codec in master mode, so there
is no need for having the 'fsl,mode' property.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Currently the HDMI controller is a child device of the AIPS bus in the
DT which is clearly wrong. Move it to the right location.
This introduces no functional change it just aligns the DT representation
with reality.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Like i.MX6, the i.MX7 code calls into the anatop driver, which fails
if that is disabled:
arch/arm/mach-imx/built-in.o: In function `imx7d_init_machine':
arch/arm/mach-imx/mach-imx7d.c:24: undefined reference to `imx_anatop_init'
arch/arm/mach-imx/built-in.o: In function `imx7d_init_irq':
arch/arm/mach-imx/mach-imx7d.c:29: undefined reference to `imx_init_revision_from_anatop'
This patch ensures that for an imx7-only build, we still get anatop
built-in, matching what we do for imx6. We also need to select
HAVE_IMX_MMDC, as that is needed by the anatop code.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
After the cleanup on imx timer driver, now it's ready to be moved into
drivers/clocksource/. Let's do it.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
It splits irq enable/disable/acknowledge operations into device specific
functions as the hooks in imx_gpt_data, so that we can save the use of
timer_is_xxx() and cpu_is_xxx() checking in these irq functions.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
We now have pointer to imx_timer structure available where timer base
address is needed, so we can just kill global timer_base by using
imxtm->base instead.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
It defines offset of gpt registers TSTAT, TCN and TCMP per device
type in imx_gpt_data, so that these registers can be accessed in an
way without timer_is_v2() checking.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Since we now have imx_timer structure, it makes more sense to move those
clock event related variables into the structure, so that we can save
some global variables.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
It creates a gpt device speicific data structure and adds function hook
gpt_setup_tctl in there to set up gpt TCTL register.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Use different initialization function in CLOCKSOURCE_OF_DECLARE() to
initialize gpt device type for DT boot.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Define an enum for gpt timer device type in include/soc/imx/timer.h to
tell the gpt block differences among SoCs. Update non-DT users (clock
drivers) to pass the device type.
As we now have include/soc/imx/timer.h, the declaration of
mxc_timer_init() is moved into there as the best fit.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Instead of passing around as individual argument, let's move timer
resources like irq and clocks together with base address into a data
structure, and pass pointer of the structure as argument to simplify
the function call interface.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Replace the __raw_readl/__raw_writel with readl_relaxed/writel_relaxed
which is endian-safe, as a step of moving the driver code into folder
drivers/clocksource.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
A recent change to the imx53 power management caused a build
regression when CONFIG_SOC_IMX53 is disabled:
mach-imx/built-in.o:(.init.rodata+0x60): undefined reference to `imx53_suspend'
mach-imx/built-in.o:(.init.rodata+0x64): undefined reference to `imx53_suspend_sz'
This avoids the problem by compiling the code in question
conditionally on the presence of CONFIG_SOC_IMX53. For
consistency, I'm also changing the same thing for
CONFIG_SOC_IMX51.
An additional benefit of this approach is reduced code size
for kernels that only include support for one of the two
SoCs.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 1579c7b9fe ("ARM: imx53: Set DDR pins to high impedance when in suspend to RAM.")
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Use the generic mechanism to declare a bitmap instead of unsigned long.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
In order to save power the DDR pins should be put into high
impedance when in suspend to RAM.
This requires manually requesting self refresh (rather than using the
automatic mode implemented by the CCM / ESDCTL), followed by
reconfiguring the IOMUXC.
Of course the code to do this cannot itself run from DDR so the
code is copied to and executed from internal memory.
In my tests using a custom i.MX53 board with LPDDR2 RAM
this reduced the suspend power consumption from 200mW to 60mW.
Signed-off-by: Martin Fuzzey <mfuzzey@parkeon.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add low level uart debug support for imx7d
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: Bai Ping <b51503@freescale.com>
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Include the "common.h" header file to fix the following sparse warning:
arch/arm/mach-imx/mmdc.c:66:5: warning: symbol 'imx_mmdc_get_ddr_type' was not declared. Should it be static?
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The comments were corrected as the following to reflect
the real situation of Freescale MXC timer IP block.
There are totally 4 version of the timer on Freescale i.MX SoCs.
Signed-off-by: Shenwei Wang <shenwei.wang@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Removed the duplicated function declaration of mxc_timer_init
which was already declared in drivers/clk/imx/clk.h.
Signed-off-by: Shenwei Wang <shenwei.wang@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The irq_domain_ops are not modified by the driver and the irqdomain core
code accepts pointer to a const data.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Commit 4631960d26da ("ARM: imx6: set initial power mode in pm function")
moves imx6_set_lpm() from clock init function into
imx6_pm_common_init(). This causes a hang when cpuidle support is
enabled. The reason for that is ARM core clock is shut down
unexpectedly by WAIT mode. It happens with the following call stack:
cpuidle_register_governor()
cpuidle_switch_governor()
cpuidle_uninstall_idle_handler()
synchronize_sched()
wait_rcu_gp()
wait_for_completion()
When wait_for_completion() is called as above, all cores are idle/WFI.
Hence, the reset value of CCM_CLPCR_LPM - WAIT mode, will trigger a
hardware shutdown of the ARM core clock.
To fix the regression, we need to ensure that CCM_CLPCR_LPM is
initialized into RUN mode earlier than cpuidle governor registration,
which is a postcore_initcall. This patch creates function
imx6_pm_ccm_init() to map CCM block and initialize CCM_CLPCR_LPM into
RUN mode, and have the function called from machine .init_irq hook,
which should be early enough.
Reported-by: Kevin Hilman <khilman@kernel.org>
Fixes: 8fb76a07e2 ("ARM: imx6: set initial power mode in pm function")
Tested-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Tyler Baker <tyler.baker@linaro.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
After the cleanup on clock drivers, they are now ready to be moved into
drivers/clk. Let's move them into drivers/clk/imx folder.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
With the cleanup done before, we now can simply define base address and
irq as needed in clock driver, to get those platform header inclusions
removed.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Instead of calling cpu_is_xxx() in clk-pllv1 driver, let's add clk-pllv1
type support to handle the difference/quirk in particular SoC designs.
Doing so will help get clk-pllv1 driver ready for being moved out of
arch/arm/mach-imx folder.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
As we're about to move clock drivers out of arch/arm/mach-imx,
cpu_is_xxx() shouldn't be used any more. Let's avoid the call by
looking at the device tree machine compatible string to determine
which SoC the clock driver is running on.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
We are about to move imx6 clock driver into drivers/clk, so let's get
imx6 pm code map CCM block on its own rather than relying on clock
driver to do the mapping.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Rather than setting initial low-power mode in every single i.MX6 clock
initialization function, we should really do that in pm code. Let's
move imx6q_set_lpm(WAIT_CLOCKED) call into imx6_pm_common_init().
While at it, let's rename the function to imx6_set_lpm() since it's
actually common for all i.MX6 SoCs.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
We are about to move imx5 clock driver into drivers/clk, so let's get
imx5 pm code map CCM block on its own rather than relying on clock
driver to do the mapping.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The revision definitions and declarations are widely used by clock
drivers. As a step of moving clock drivers out of arch/arm/mach-imx,
let's create header include/soc/imx/revision.h to accommodate them.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Pass physical address of timer block to mxc_timer_init() call, which in
turn does dynamic mapping within the function. Thus, we can avoid using
static mapping in clock drivers.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The Odroid XU3 Lite is almost the same as XU3, except:
1. Lower CPU frequencies (1.8 GHz for A15 and 1.3 GHz for A7, instead of
2.0 GHz and 1.4 GHz).
2. No DisplayPort.
3. No TI INA231 energy measurement sensors.
This patch moves common nodes (which is almost everything) to a common
DTSI file and adds a new XU3 Lite DTS.
Currently in comparison to XU3, only the INA231 sensors are disabled to
remove the warning:
ina2xx 0-0040: error configuring the device: -6
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The IRQB of S2MPS11 PMIC is wired to XEINT4 (GPX0-4) through pull-up
resistor.
Add interrupt properties and pinctrl configuration to enable RTC wake
alarm of rtc-s5m driver. This also removes a warning:
sec_pmic 4-0066: No interrupt specified, no interrupts
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Add nodes for jpeg codec in Exynos5420 SoC.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
[k.kozlowski: fixed up minor differences for applying]
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Add new labels to certain nodes on S3C2416 so they could be easily
referenced by board DTS files.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes. Additionally remove duplicated serial and uart labels
for serial.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The i2c_7 node (i2c@12CD0000) with LVDS bridge child node was put in
Exynos5250 Snow DTS file twice. Move the LVDS bridge to proper existing
i2c_7 node.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Add new labels to certain nodes so they could be easily referenced by
Exynos5 board DTS files.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
PWM output wasn't working because it wasn't hooked up to its pincontrol.
This patch:
- hooks up PWM to its pincontrol, and documents what
the outputs are on the XU3
- switches the LEDs that are on PWM outputs to use PWM
rather than GPIO.
The main effect is that the brightness of the LEDs can be controlled, and
user-mode fan control is enabled via /sys/class/pwm
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Peter Chubb <peter.chubb@nicta.com.au>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
For thermal zones:
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Add new labels to certain nodes so they could be easily referenced by
Exynos4 board DTS files.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Since e4b3d38088 ("phy: exynos-video-mipi: Fix regression by adding
support for PMU regmap") the Exynos PMU driver provides regmap to access
the MIPI DPHY registers. The MIPI DPHY driver accesses this regmap
through syscon phandle.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Since e4b3d38088 ("phy: exynos-video-mipi: Fix regression by
adding support for PMU regmap") the Exynos PMU driver provides
regmap to access the MIPI DPHY registers. The MIPI DPHY node uses
a phandle to syscon to get this regmap. The 'reg' field is obsolete.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Replace fixed parent with last parent (obtained with clk_get_parent())
of clocks for devices in mfc and disp power domains. This should improve
behavior if such clocks were reparented by the drivers and new parents
are different than those specified in DTS.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Enable CONFIG_SENSORS_PWM_FAN on exynos_defconfig to control fan
power on Odroid-XU3.
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The Mele A1000G-quad and the Mele M9 have the same PCB, sofar we've been using
the same dts for both models. Unfortunately this does not work for the otg
controller, on the M9 this is routed to a micro-usb connector on the outside,
while as on the A1000G-quad it is connected to an usb to sata bridge
(which is not populated on the M9 pcb).
This commit adds a new dts for the Mele-A1000G-quad to allow using
different otg controller settings on the 2 boards.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The ga10h is an 10" tablet with an A33 or A23 soc, 1G RAM, 8G or 16G nand,
sdio wifi, 2 micro usb ports, 1 otg and 1 host and 1 micro sd slot.
This commit adds a dts file for the v1.1 pcb with an a33 soc.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The SinA33 is a core/SDK development board by Sinlinx. The core board
does not have any connectors or pads, other than the pads used to connect
it to the SDK board.
The core board only has the A33 SoC, 2 RAM chips, an eMMC flash chip,
the AXP223 PMIC, and supporting discrete components. eMMC is optional.
The SDK board has a USB host, USB OTG, volume control and home buttons,
audio input/output jacks, a micro-SD slot, camera and SDIO expansion
headers, an LCD connector, and a GPIO expansion header, which has
UARTs, MIPI DSI and I2C available. Only UART0 is enabled though.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A33 adds an additional pinmux option for uart0 on the PB pins.
This was not present on the A23. Nor is it available on the H3,
which does not have the PB pingroup.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
mmc2 is mostly used with eMMC flash chips, as an alternative to
raw NAND flash chips. 8 bit mmc is commonly used.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The SOCrates has three HPS LEDs that can be turned on/off via gpio.
Use the first one has heartbeat and add the other two as free LEDs.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Add the enable-method property for the cpu node on socfpga.dtsi and
socfpga_arria10.dtsi. This is for CPU_METHOD_OF_DECLARE to use to enable
the secondary core.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
This splits off the reservation of the memory occupied by the FDT
binary itself from the processing of the memory reservations it
contains. This is necessary because the physical address of the FDT,
which is needed to perform the reservation, may not be known to the
FDT driver core, i.e., it may be mapped outside the linear direct
mapping, in which case __pa() returns a bogus value.
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Some of the OMAP based boards e.g. am437x-gp-evm have
the Pixcir touch controller. Enable the related device
driver.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
A recent change in kernel/acct.c added a new warning for many
configurations on ARM:
kernel/acct.c: In function 'acct_pin_kill':
arch/arm/include/asm/cmpxchg.h:122:3: warning: value computed is not used [-Wunused-value]
The code is in fact correct, it's just a cmpxchg() call that
intentionally ignores the result, and no other code does that. The
warning does not show up on x86 because of the way that its cmpxchg()
macro is written. This changes the ARM implementation to use a similar
construct with a compound expression instead of a typecast, which causes
the compiler to not complain about an unused result.
Fix the other macros in this file in a similar way, and place them
just below their function implementations.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Vybrids has 112 peripheral interrupts which can be routed to the
Cortex-M4's NVIC interrupt controller.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The ARM Dual-Timer SP804 module is peripheral found not only on ARM32
platforms but also on ARM64 platforms.
This patch moves the driver out of arch/arm to driver/clocksource
so that it can be used on ARM64 platforms also.
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Rob Herring <robh@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Olof Johansson <olof@lixom.net>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The header asm/hardware/arm_timer.h is included in various machine
specific files to access TIMER_CTRL and initialise to a known state.
This patch introduces a new function sp804_timer_disable to disable
the SP804 timers and uses the same for initialising the timers to
known(off) state, thereby removing the dependency on the header
asm/hardware/arm_timer.h
This change is in prepartion to move sp804 timer support out of arch/arm
so that it can be used on ARM64 platforms.
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Olof Johansson <olof@lixom.net>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The new veneer support for loadable modules on ARM uses the
__opcode_to_mem_thumb32() function to count R_ARM_THM_CALL
and R_ARM_THM_JUMP24 relocations.
However, this function is not defined for big-endian kernels
on ARMv5 or before, causing a compile-time error:
arch/arm/kernel/module-plts.c: In function 'count_plts':
arch/arm/kernel/module-plts.c:124:9: error: implicit declaration of function '__opcode_to_mem_thumb32' [-Werror=implicit-function-declaration]
__opcode_to_mem_thumb32(0x07ff2fff)))
^
As we know that this part of the function is only needed for
Thumb2 kernels, and that those can never happen with BE32,
we can avoid the error by enclosing the code in an #ifdef.
Fixes: 7d485f647c ("ARM: 8220/1: allow modules outside of bl range")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Put secondary_startup_arm() prototype in arch/arm/include/asm/smp.h
so users doesn't have to add extern prototype in their code.
Signed-off-by: Yingjoe Chen <yingjoe.chen@mediatek.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
secondary_startup_arm is used as ARM mode secondary start up function
when ther kernel is compiled in THUMB mode, however the label itself
is still in .thumb mode. readelf shows:
160979: c020a581 120 FUNC GLOBAL DEFAULT 2 secondary_startup_arm
Make sure the label is in ARM mode as well.
Signed-off-by: Yingjoe Chen <yingjoe.chen@mediatek.com>
Tested-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add an usb_clk node for a23/a33.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
ET-Q8_A33 is A33 based cheap tablet in common Q8 format.
It has 512MB RAM, 4GB Nand, 7" Display, RDA5900P wifi, GSL1680 touch, etc.
Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Chen-Yu Tsai <wens@csie.org>
Add a dtsi file for use with a33 based boards based on the new
sun8i-a23-a33.dtsi file.
Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Chen-Yu Tsai <wens@csie.org>
Rename sun8i-a23.dtsi to sun8i-a23-a33.dtsi as the base dtsi for the A33
is 99% the same and add a new sun8i-a23.dtsi including sun8i-a23-a33.dtsi
and setting the few things not shared with the A33 (mbus-clk, pio
compatible and interrupts).
Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Chen-Yu Tsai <wens@csie.org>
Conflicts:
drivers/net/phy/amd-xgbe-phy.c
drivers/net/wireless/iwlwifi/Kconfig
include/net/mac80211.h
iwlwifi/Kconfig and mac80211.h were both trivial overlapping
changes.
The drivers/net/phy/amd-xgbe-phy.c file got removed in 'net-next' and
the bug fix that happened on the 'net' side is already integrated
into the rest of the amd-xgbe driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
Register crypto hwmod links only if they are not disabled in DT.
If DT information is missing, enable them only for GP devices.
Before this patch crypto hwmod links were always disabled for all HS
devices and it was not possible to use omap-aes and omap-sham linux
drivers.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
[paul@pwsan.com: move the complex IP-block presence heuristics into their
own function to simplify the code; fix some checkpatch warnings]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Without this patch function pm_runtime_get_sync() returns 0 even when
some omap subfunction fails. This patch properly propagate error codes
from omap functions back to caller.
This patch fix problem, when loading omap-aes driver in qemu cause
kernel oops.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
[paul@pwsan.com: fix a checkpatch warning]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Without a hwmod for am43xx emif use counting for emif clockdomain does
not happen correctly so it may be shut off by pm code unintentionally.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
[paul@pwsan.com: updated to apply]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
We support decoding the bootloader values if DEBUG is defined.
But we also need to change the struct omap_hwmod flags to have
HWMOD_INIT_NO_RESET to avoid the GPMC being reset during the
boot. Otherwise just the default timings will be displayed
instead of the bootloader configured timings.
This also allows us to clean up the various GPMC related
hwmod flags. For debugging, we only need HWMOD_INIT_NO_RESET,
and HWMOD_INIT_NO_IDLE is not needed.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Document that r13 is not a stack in the initialisation function, in
case anyone gets other ideas.
Document the registers available for the errata workarounds, and
specifically which registers contain parts of the MIDR register, as
well as which registers must be preserved.
Lastly, use the lowest numbered available register (r0) rather than
r10 for temporary storage.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We already have the main ID register available in r9, there's no need
to refetch it. Use the saved value.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rather than having a long sprawling __v7_setup function, which is hard
to maintain properly, move the CPU errata out of line.
While doing this, it was discovered that the Cortex-A15 errata had been
incorrectly added:
ldr r10, =0x00000c08 @ Cortex-A8 primary part number
teq r0, r10
bne 2f
/* Cortex-A8 errata */
b 3f
2: ldr r10, =0x00000c09 @ Cortex-A9 primary part number
teq r0, r10
bne 3f
/* Cortex-A9 errata */
3: ldr r10, =0x00000c0f @ Cortex-A15 primary part number
teq r0, r10
bne 4f
/* Cortex-A15 errata */
4:
This results in the Cortex-A15 test always being executed after the
Cortex-A8 and Cortex-A9 errata, which is obviously not what is intended.
The 'b 3f' labels should have been updated to 'b 4f'. The new structure
of:
/* Cortex-A8 Errata */
ldr r10, =0x00000c08 @ Cortex-A8 primary part number
teq r0, r10
beq __ca8_errata
/* Cortex-A9 Errata */
ldr r10, =0x00000c09 @ Cortex-A9 primary part number
teq r0, r10
beq __ca9_errata
/* Cortex-A15 Errata */
ldr r10, =0x00000c0f @ Cortex-A15 primary part number
teq r0, r10
beq __ca15_errata
__errata_finish:
is much cleaner and easier to see that this kind of thing doesn't
happen.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Re-engineer the LPAE TTBR setup code. Rather than passing some shifted
address in order to fit in a CPU register, pass either a full physical
address (in the case of r4, r5 for TTBR0) or a PFN (for TTBR1).
This removes the ARCH_PGD_SHIFT hack, and the last dangerous user of
cpu_set_ttbr() in the secondary CPU startup code path (which was there
to re-set TTBR1 to the appropriate high physical address space on
Keystone2.)
Tested-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Eliminate the needless nommu version of this function, and get rid of
the proc_info_list structure argument - we no longer need this in order
to fix up the page table entries.
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Tested-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Re-implement the physical address space switching to be architecturally
compliant. This involves flushing the caches, disabling the MMU, and
only then updating the page tables. Once that is complete, the system
can be brought back up again.
Since we disable the MMU, we need to do the update in assembly code.
Luckily, the entries which need updating are fairly trivial, and are
all setup by the early assembly code. We can merely adjust each entry
by the delta required.
Not only does this fix the code to be architecturally compliant, but it
fixes a couple of bugs too:
1. The original code would only ever update the first L2 entry covering
a fraction of the kernel; the remainder were left untouched.
2. The L2 entries covering the DTB blob were likewise untouched.
This solution fixes up all entries.
Tested-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The init_meminfo() method is not about initialising meminfo - it's about
fixing up the physical to virtual translation so that we use a different
physical address space, possibly above the 4GB physical address space.
Therefore, the name "init_meminfo()" is confusing.
Rename it to pv_fixup() instead.
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Tested-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There is no point platform code doing this, let's move it into the
generic code so it doesn't get duplicated.
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Tested-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Make the init_meminfo function return the offset to be applied to the
phys-to-virt translation constants. This allows us to move the update
into generic code, along with the requirements for this update.
This avoids platforms having to know the details of the phys-to-virt
translation support.
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Tested-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We ideally want the init_meminfo function to do nothing but return the
delta to be applied to PHYS_OFFSET - it should do nothing else. As we
can detect in platform init code whether we are running in the high
physical address space, move the platform notifier initialisation
entirely into the platform init code.
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Tested-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This removes the no longer required return statement at the end
of the void function, omap2_show_dma_cap due to no need for a
return statement due to this function always running successfully.
Signed-off-by: Nicholas Krause <xerofoify@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Avoid entering "RTC-only mode" at poweroff. It is unsupported by most
versions of BeagleBone, and risks hardware damage.
The damaging configuration is having system-power-controller
without ti,pmic-shutdown-controller.
Reported-by: Matthijs van Duin <matthijsvanduin@gmail.com>
Tested-by: Matthijs van Duin <matthijsvanduin@gmail.com>
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Johan Hovold <johan@kernel.org>
[Matthijs van Duin: added explanatory comments]
Signed-off-by: Matthijs van Duin <matthijsvanduin@gmail.com>
Fixes: http://bugs.elinux.org/issues/143
Cc: stable@vger.kernel.org # v3.12+
[tony@atomide.com: updated comments with the hardware breaking info]
Signed-off-by: Tony Lindgren <tony@atomide.com>
New system control module layout for omap3 overlooked parts of the am35xx
configuration. Basically the am35xx clocks were not converted to use the
changed offsets, which caused weird boot warnings. The errors were not
fatal so far, so they were not caught earlier. Fixed by applying the
proper offsets for the AM35xx scm clocks.
Fixes: b8845074cf ("ARM: dts: omap3: add minimal l4 bus layout with...")
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reported-by: Jeroen Hofstee <linux-arm@myspectrum.nl>
Cc: Paul Walmsley <paul@pwsan.com>
Tested-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
- Enable i.MX7D and LS1021A SoC support
- Enable support for WL1271 WIFI/BT, SX8654 I2C touchscreen and PCF8523
RTC, which can be found on Armadeus Systems APF6 and Cubox-i boards.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVbArDAAoJEFBXWFqHsHzOaMoIAJrdhMHWKpTys4OmQOao0qE1
uHCrGHlAcWGy8xgoA617D3PLahP9QMID9GUFxH8cWRa4ifBEybn9nqyQFU/Sp6CM
cwRNXvscupvnPQcZIbpQlJezaBH2pqm43BOWi5b77/ASdh+xad7JFGniOb6P5L2Q
iplE12VVDkg70t3tOh7lHgrRs5I/1DL3/JSCTh7KEEjxr0wBkR68/b3ONP3eqnhP
txa+mW1fh61l3VZ8qzff8T1yvyft/onoqbzfN9BVITlKDrWe3NSM/jalM9h1o5T3
orlj3rLacJhdSpWUtCK+M8BovdaI549wNk7HnDH1lNzawUJ3m8b7Y1uuAfkAhGI=
=DIH7
-----END PGP SIGNATURE-----
Merge tag 'imx-defconfig-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/defconfig
Merge "The i.MX defconfig updates for 4.2" from Shawn Guo:
- Enable i.MX7D and LS1021A SoC support
- Enable support for WL1271 WIFI/BT, SX8654 I2C touchscreen and PCF8523
RTC, which can be found on Armadeus Systems APF6 and Cubox-i boards.
* tag 'imx-defconfig-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: imx_v6_v7_defconfig: updates for Armadeus Systems APF6 boards
ARM: config: imx_v6_v7_defconfig add imx7d support
ARM: imx_v6_v7_defconfig: Select LS1021A
ARM: imx_v6_v7_defconfig: Enable RTC PCF8523 support
- Document Snoop Control Unit (SCU) bindings
- Document Ux500 board bindings
- Define the backup RAM in the DBx500 device tree
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=IRmr
-----END PGP SIGNATURE-----
Merge tag 'dt-for-armsoc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into next/dt
Merge "Device Tree changes for Ux500 and ARM SOC" from Linus Walleij:
- Document Snoop Control Unit (SCU) bindings
- Document Ux500 board bindings
- Define the backup RAM in the DBx500 device tree
* tag 'dt-for-armsoc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ARM: ux500: define the backupram in the device tree
ARM: ux500: add board documentation
ARM: scu: document Snoop Control Unit DT bindings
STM32 clocksource driver needs to be selected if ARCH_STM32.
Signed-off-by: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Merge "changes for Broadcom SoCs":
- Dan fixes an error path in the BCM63xx SMP code
- Ray adds the relevant Kconfig selects to enable the Broadcom NAND driver on Cygnus
- Kevin provides a change to the Broadcom GISB arbiter driver to make it work with
MIPS-based big-endian STB SoCs (this was a long-standing change that had dependencies on
code in drivers/of/*)
- Gregory enables the use of GPIOLIB for brcmstb SoCs and bumps the number of GPIOs for
these platforms
* tag 'arm-soc/for-4.2/soc-part2' of http://github.com/broadcom/stblinux:
ARM: brcmstb: Add default gpio number
ARM: brcmstb: Select ARCH_WANT_OPTIONAL_GPIOLIB
bus: brcmstb_gisb: Honor the "big-endian" and "native-endian" DT properties
ARM: BCM: Enable NAND support for iProc SoCs
ARM: BCM63xx: fix an error path in bcm63xx_pmb_power_on_cpu()
Merge "This pull request contains a single change" from Florian Fainelli:
- fix the NAND controller node on bcm63138, the original change was a mis-merge that
did not properly parent it to the "ubus" node
* tag 'arm-soc/for-4.2/dts-fixes' of http://github.com/broadcom/stblinux:
ARM: dts: BCM63xx: re-parent NAND controller node
Add 2 new set boards:
- Armada 385 based Linksys boards
- DLink DNS-327L
Update the spi-nor flash compatible strings
Use improved armada spi device tree compatible name for each mvebu SoC
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlVo3bwACgkQCwYYjhRyO9UxNgCgn5KoYMnx0qzbbmc7rfoyd9g3
IF8An0yb+2EFpP7SBPu41s8rXOATCCTb
=APjz
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt-4.2-2' of git://git.infradead.org/linux-mvebu into next/dt
Merge "mvebu dt changes for v4.2 (part #2)" from Gregory CLEMENT:
Add 2 new set boards:
- Armada 385 based Linksys boards
- DLink DNS-327L
Update the spi-nor flash compatible strings
Use improved armada spi device tree compatible name for each mvebu SoC
* tag 'mvebu-dt-4.2-2' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: use improved armada spi device tree compatible name for each SoC
ARM: mvebu: dts: Add dts file for DLink DNS-327L
ARM: mvebu: add "jedec,spi-nor" flash compatible binding
ARM: kirkwood: add "jedec,spi-nor" flash compatible binding
ARM: mvebu: add support for the new Armada 385 based Linksys boards
mvebu-mbus: add mv_mbus_dram_info_nooverlap() needed for the new
Marvell crypto driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlVo26sACgkQCwYYjhRyO9UQ4gCeLb6E7RWXGXtLBXRvRi+1a5Vm
GckAn2a/4vAQExwlDsiqHMsM2Iw9Phc7
=1es8
-----END PGP SIGNATURE-----
Merge tag 'mvebu-drivers-4.2' of git://git.infradead.org/linux-mvebu into next/drivers
Merge "mvebu drivers change for 4.2" from Gregory CLEMENT:
mvebu-mbus: add mv_mbus_dram_info_nooverlap() needed for the new
Marvell crypto driver
* tag 'mvebu-drivers-4.2' of git://git.infradead.org/linux-mvebu:
bus: mvebu-mbus: add mv_mbus_dram_info_nooverlap()
Based on the earlier bug fixes branch, which contains six other
patches already merged into 4.1.
wakeup to stacked domains. This allows waking up the device from
suspend to RAM using S3C RTC driver (the RTC on SoC).
The patch should be applied some time ago, unfortunately
it seems it slipped through fingers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=BUV3
-----END PGP SIGNATURE-----
Merge tag 'samsung-fixes-4.1-4' of https://github.com/krzk/linux into fixes
Merge "ARM: EXYNOS: Fix for 4.1, 4th" from Krzysztof Kozlowski:
Fix for Exynos3250 RTC wake-up interrupts after converting PMU
wakeup to stacked domains. This allows waking up the device from
suspend to RAM using S3C RTC driver (the RTC on SoC).
The patch should be applied some time ago, unfortunately
it seems it slipped through fingers.
* tag 'samsung-fixes-4.1-4' of https://github.com/krzk/linux:
ARM: exynos: Fix wake-up interrupts for Exynos3250
Disable unused internal RTC for Mamba from linksys (Armada XP)
And 2 commits fixing regressions on mvebu-mbus:
- the first one for Kirkwood or Orion SoC
- the second one for DMA when the platform have more than 4GB (only
possible on Armada XP as far as I know)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlVo2BIACgkQCwYYjhRyO9Vf4ACZAUuChGNGu5zOwme4AHCuimp6
TnYAn2n7DjGJ+0aOHCY6qAsVGCUdnda9
=FvVk
-----END PGP SIGNATURE-----
Merge tag 'mvebu-fixes-4.1-3' of git://git.infradead.org/linux-mvebu into fixes
Merge "mvebu fixes for 4.1 (part 3)" from Gregory CLEMENT:
Disable unused internal RTC for Mamba from linksys (Armada XP)
And 2 commits fixing regressions on mvebu-mbus:
- the first one for Kirkwood or Orion SoC
- the second one for DMA when the platform have more than 4GB (only
possible on Armada XP as far as I know)
* tag 'mvebu-fixes-4.1-3' of git://git.infradead.org/linux-mvebu:
Revert "bus: mvebu-mbus: make sure SDRAM CS for DMA don't overlap the MBus bridge window"
bus: mvebu-mbus: do not set WIN_CTRL_SYNCBARRIER on non io-coherent platforms.
ARM: mvebu: armada-xp-linksys-mamba: Disable internal RTC
All ARMv5 and older CPUs invalidate their caches in the early assembly
setup function, prior to enabling the MMU. This is because the L1
cache should not contain any data relevant to the execution of the
kernel at this point; all data should have been flushed out to memory.
This requirement should also be true for ARMv6 and ARMv7 CPUs - indeed,
these typically do not search their caches when caching is disabled (as
it needs to be when the MMU is disabled) so this change should be safe.
ARMv7 allows there to be CPUs which search their caches while caching is
disabled, and it's permitted that the cache is uninitialised at boot;
for these, the architecture reference manual requires that an
implementation specific code sequence is used immediately after reset
to ensure that the cache is placed into a sane state. Such
functionality is definitely outside the remit of the Linux kernel, and
must be done by the SoC's firmware before _any_ CPU gets to the Linux
kernel.
Changing the data cache clean+invalidate to a mere invalidate allows us
to get rid of a lot of platform specific hacks around this issue for
their secondary CPU bringup paths - some of which were buggy.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Thierry Reding <treding@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Tested-by: Wei Xu <xuwei5@hisilicon.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The A20 has a few SRAM that can be mapped either to a device or to the CPU,
with the mapping being controlled by a SRAM controller.
Add the SRAM controller, the SRAM that it drives and the section that can
be used by the various devices.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
The A10s and A13 have a few SRAM that can be mapped either to a device or
to the CPU, with the mapping being controlled by a SRAM controller.
Add the SRAM controller, the SRAM that it drives and the section that can
be used by the various devices.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
The A10 has a few SRAM that can be mapped either to a device or to the CPU,
with the mapping being controlled by a SRAM controller.
Add the SRAM controller, the SRAM that it drives and the section that can
be used by the various devices.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
This patch reverts commit ccb4ada2f1 ("ARM: dts: sun7i: Add A20 SRAM and
SRAM controller"), commit e6f51e4bd2 ("ARM: dts: sun5i: Add A13 and A10s
SRAM and SRAM controller") and commit 6d92b80f35 ("ARM: dts: sun4i: Add
A10 SRAM and SRAM controller").
The bindings have been changed in the SRAM driver, and we need to
change the DT accordingly.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
On A80 there are 2 watchdogs, one in the main block, and one in the
R (special) block. We do not have information on the R block watchdog,
other than the register layout is the same, and the interrupt number.
Both are able to reset the whole system.
Add the main watchdog, in case the R block is used for special purposes
like running an RTOS.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The BananaPro uses uart4 for the default rx/tx pins on the 40 pins connector,
so enable uart4.
Uart2 is also available at the bananapro io-pins, but like on the bananapi
the primary function of the pins is to act as gpios, see:
http://forum.lemaker.org/forum.php?mod=viewthread&tid=10852
Remove the uart2 node, people who want to use uart2 can do so with a
devicetree-overlay.
Signed-off-by: Michael Ring <mail@michael-ring.org>
[hdegoede@redhat.com: Remove uart2 node]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Some boards (e.g. the BananaPro) use alternative pins for uart4, add a pinmux
entry for these.
Signed-off-by: Michael Ring <mail@michael-ring.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A23 Evaluation Board has an MMC slot, two UARTs, NAND, a few display
connectors (RGB, MIPI, LVDS), a mini-PCIE slot, USB host and OTG and a
bunch of embedded sensors.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Commit 8b283c0254 (ARM: exynos4/5: convert pmu wakeup to
stacked domains) changed the Exynos PMU code to use stacked
domains. This has led to a number of interrupt numbers to be
fixed.
In the meantime, support for Exynos 3250 was added, missing
the required change to this platform. This amounts to revert
ace283a04a (ARM: EXYNOS: Fix wrong hwirq of RTC interrupt
for Exynos3250 SoC), as the initial patch was right, just a
bit early...
Cc: Chanwoo Choi <cw00.choi@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Cc: Kukjin Kim <kgene@kernel.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Pull ARM fixes from Russell King:
"Three fixes this time around:
- fix a memory leak which occurs when probing performance monitoring
unit interrupts
- fix handling of non-PMD aligned end of RAM causing boot failures
- fix missing syscall trace exit path with syscall tracing enabled
causing a kernel oops in the audit code"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 8357/1: perf: fix memory leak when probing PMU PPIs
ARM: fix missing syscall trace exit
ARM: 8356/1: mm: handle non-pmd-aligned end of RAM
Two weeks worth of small bug fixes this time, nothing sticking out
this time:
- one defconfig change to adapt to a modified Kconfig symbol
- two fixes for i.MX for backwards compatibility with older DT
files that was accidentally broken
- one regression fix for irq handling on pxa
- three small dt files on omap, and one each for imx and exynos
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIVAwUAVWjV6WCrR//JCVInAQKwABAA4ZCvaRoP5Yc9aIGVZx5/FRSaXQ7pMi39
ORggazaHWZ3NpMDMfVqhBzyeZya3Ad6pjaIsPL83GdcqJgu5O+bNF86f5r4Q5rWK
bvLPQd77ge4SCvqgQw8CgR/05aiLGhMlujKQeIR+P4z21p5OFoPqRjQnAzjWbRde
lm6sO8I3xQybagyjp4y1/uxW4Ukc0fRNM+sMnQbVwRlCM6L+CGGWuyCuAseM8MrH
eGqlHutZTt3/3TB/Y+gerohchxgq2+YVAUFhMoaVl+UUwW0Qk7Ee9roKfruiWuMk
9fvPMeaw/CkwpUSZreGjBPsGINWWRQPleWzWHEvjiOyALooM1h/LRL6JJH/nodnV
w2F4ECjdGxfdEXn4ShMYg8ZfdXMswpB8CaAOFH3dTQyXo4Yy0bfXB3EakiOjmoZW
Nst3vCI0IYq6kLnOOLzNfVZy6VQQtA3oNShCILvHKwyqVkSfX998a365otW5xAXJ
2D2GAjGxNNp+Rg5QJ++OEwQrpha6DtyvuGffIB/DQMLpqkizvMQyK7x+nAvUaKQ7
OdxEs8Npm7i78wd84mNqXKosbq9yHUlbOU7PVlOfjL/JjXi1jDhPBTtKvnSZHTyr
Np0/FI1iJqUf9//L1z8Dz0CE8G/DLQe7NG847HsBkLbqudtNY2Hcr7IOSs9eJdp3
DEG/377/2mM=
=2HQg
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"Two weeks worth of small bug fixes this time, nothing sticking out
this time:
- one defconfig change to adapt to a modified Kconfig symbol
- two fixes for i.MX for backwards compatibility with older DT files
that was accidentally broken
- one regression fix for irq handling on pxa
- three small dt files on omap, and one each for imx and exynos"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: multi_v7_defconfig: Replace CONFIG_USB_ISP1760_HCD by CONFIG_USB_ISP1760
ARM: imx6: gpc: don't register power domain if DT data is missing
ARM: imx6: allow booting with old DT
ARM: dts: set display clock correctly for exynos4412-trats2
ARM: pxa: pxa_cplds: signedness bug in probe
ARM: dts: Fix WLAN interrupt line for AM335x EVM-SK
ARM: dts: omap3-devkit8000: Fix NAND DT node
ARM: dts: am335x-boneblack: disable RTC-only sleep
ARM: dts: fix imx27 dtb build rule
ARM: dts: imx27: only map 4 Kbyte for fec registers
Out of the brcmstb SoCs that I know, BCM3390 has the largest numbers
of GPIOs, with its
- 320 "peripheral" GPIOs
- 5*32 = 160 UPG GPIOs (counting unused lines, which do get counted)
- 2*32 = 64 UPG AON GPIOs (counting unused lines)
Total: 544
I suspect that the upper limit will only need to be higher in the
future, so set it to 1024.
Signed-off-by: Gregory Fong <gregory.0xf0@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Select ARCH_WANT_OPTIONAL_GPIOLIB from BRCMSTB to allow GPIOLIB and
GPIO_BRCMSTB to be enabled.
Signed-off-by: Gregory Fong <gregory.0xf0@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Fix dts to match what the Linux kernel expects. This works around
touchscreen problems in 4.1 linux on Nokia n900.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This is needed for USB on dm816x-evm.
Cc: Bin Liu <binmlist@gmail.com>
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: George Cherian <george.cherian@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This ethernet device is used on devkit8000 board.
Signed-off-by: Anthoine Bourgeois <anthoine.bourgeois@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
With commit 3e457371f4 ("usb: musb: Fix fifo reads for dm816x with
musb_dsps") we need to use the right compatible flag to avoid issues
with FIFO reads.
Cc: Bin Liu <binmlist@gmail.com>
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: George Cherian <george.cherian@ti.com>
Fixes: 3e457371f4 ("usb: musb: Fix fifo reads for dm816x with musb_dsps")
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Merge cleanups from Russell King:
* 'for-arm-soc' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: Show proper respect for Heinrich Hertz by using the correct unit for frequency
* Only select sound drivers that build
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=nfP3
-----END PGP SIGNATURE-----
Merge tag 'renesas-soc-for-v4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/soc
Merge "Renesas ARM Based SoC Updates for v4.2" from Simon Horman:
* Only select sound drivers that build
* tag 'renesas-soc-for-v4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: only select sound drivers that build
Remove the generic 8250 config option so that the LPC18xx
specific option gets picked instead.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Since commit 100832abf0 ("usb: isp1760: Make HCD support
optional"), CONFIG_USB_ISP1760_HCD is automatically selected when
needed. Enabling that option in the defconfig is now a no-op, and no
longer enables ISP1760 HCD support.
Re-enable the ISP1760 driver in the defconfig by enabling
USB_ISP1760_HOST_ROLE instead.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
It includes a couple of fixes for i.MX6 GPC code to let the new kernel
be able to boot with old DTBs:
- Booting v4.1-rc kernel with old DTBs will fail with a fat warning
(require low-level debug to be seen), due to the adoption of stacked
IRQ domain. The first fix improves the situation by allowing kernel
boot up with old DTBs, although suspend/resume still breaks.
- Booting new kernel with old DTBs that do not have power-domain info
will result in a hang. The second patch fixes the hang by skipping
the kernel power-domain registration if DTB has no power-domain info.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVZalkAAoJEFBXWFqHsHzOk7YH/iQwidJWob015NvrsqUvQlDb
+dIFmUJNFpGqbkLjINDJv0p13lfksuCQ29F/b0R86+sWsRVS/JUKRkVZ1qh83lc9
8ywiTDUqJBEUApwTaVDDqWr6bbYYHC9TdZ/MqJ85hnF2PnwjBS1Vuv+WQuQe/8ru
7LuTzWyqce8u/cYi/0Zs0Vrtmsz5pjhh7Xg1iWXtamJ43v+yqDP/OwZ5BdSkT+P4
J7WWAojVz4iVG4ftNSdJ1CqGuaFP4iMg+HUoS4ecEsyhe6CMdDoq+I2Fuf1aZweS
6clSe/X2HCi7Gspv9oELsNVEci6AfFR/0Ut6LgvSya8AjxZgdu3cmbdDtbPSQ+o=
=dMJE
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-4.1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
Merge "The i.MX fixes for 4.1, 3rd round" from Shawn Guo:
It includes a couple of fixes for i.MX6 GPC code to let the new kernel
be able to boot with old DTBs:
- Booting v4.1-rc kernel with old DTBs will fail with a fat warning
(require low-level debug to be seen), due to the adoption of stacked
IRQ domain. The first fix improves the situation by allowing kernel
boot up with old DTBs, although suspend/resume still breaks.
- Booting new kernel with old DTBs that do not have power-domain info
will result in a hang. The second patch fixes the hang by skipping
the kernel power-domain registration if DTB has no power-domain info.
* tag 'imx-fixes-4.1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: imx6: gpc: don't register power domain if DT data is missing
ARM: imx6: allow booting with old DT
- Set display clock correctly for exynos4412-trats2
: fix the following error
exynos-drm: No connectors reported connected with modes
[drm] Cannot find any crtc or sizes - going 1024x768
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=U0hO
-----END PGP SIGNATURE-----
Merge tag 'samsung-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into fixes
Merge "Samsung fix for v4.1" from Kukjin Kim:
- Set display clock correctly for exynos4412-trats2
: fix the following error
exynos-drm: No connectors reported connected with modes
[drm] Cannot find any crtc or sizes - going 1024x768
* tag 'samsung-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: dts: set display clock correctly for exynos4412-trats2
* Describe DMA for the serial ports of R-Car Gen2 SoCs
* Add MMCIF max-frequency to R-Car Gen2 SoCs
* Use "nor-jedec" instead of "jedec,spi-nor"
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=OIk0
-----END PGP SIGNATURE-----
Merge tag 'renesas-dt2-for-v4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Merge "Second Round of Renesas ARM Based SoC DT Updates for v4.2" from Simon Horman:
* Describe DMA for the serial ports of R-Car Gen2 SoCs
* Add MMCIF max-frequency to R-Car Gen2 SoCs
* Use "nor-jedec" instead of "jedec,spi-nor"
* tag 'renesas-dt2-for-v4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: r8a7790 dtsi: Describe DMA for the serial ports
ARM: shmobile: r8a7791 dtsi: Describe DMA for the serial ports
ARM: shmobile: r8a7794 dtsi: Describe DMA for the serial ports
ARM: shmobile: r8a7791: add MMCIF max-frequency
ARM: shmobile: r8a7790: add MMCIF max-frequency
ARM: shmobile: bockw dts: Replace "nor-jedec" by "jedec,spi-nor"
ARM: shmobile: henninger dts: Replace "nor-jedec" by "jedec,spi-nor"
ARM: shmobile: bockw-reference dts: Replace "nor-jedec" by "jedec,spi-nor"
ARM: shmobile: koelsch dts: Replace "nor-jedec" by "jedec,spi-nor"
ARM: shmobile: lager dts: Replace "nor-jedec" by "jedec,spi-nor"
- Fix aliases and stdout properties
- Document current TTC binding
- Add Ceva to prefixes
- Use new compatible string for MACB
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)
iEYEABECAAYFAlVmuqQACgkQykllyylKDCEKxgCgl/50lxDs3V9bRw5JUiN0ClM/
lCoAn2OfNpK5w/HmOw57erYuIA0rPQc8
=ulOE
-----END PGP SIGNATURE-----
Merge tag 'zynq-dt-for-4.2' of https://github.com/Xilinx/linux-xlnx into next/dt
Merge "arm: Xilinx Zynq dt patches for v4.2" from Michal Simek:
- Fix aliases and stdout properties
- Document current TTC binding
- Add Ceva to prefixes
- Use new compatible string for MACB
* tag 'zynq-dt-for-4.2' of https://github.com/Xilinx/linux-xlnx:
ARM: zynq: DT: Use the zynq binding with macb
of: Add vendor prefix for Ceva
PCI: xilinx: Trivial fix in DT example
devicetree: cadence_ttc: Document binding for timer width
ARM: dts: zynq: Fix stdout-path and bootargs
ARM: dts: zynq: Add missing alias node for zybo and parallella
- Configure MMC data lines 4..8 for 1.8V IO on boards that
are using them as GPIOs instead of MMC data lines
- Add support for Baltos IR5221
- Add device tree support for LogicPD Torpedo devkit
- Add 3717 core pinctrl region
- Add gta04 1w and GSM audio support
- Add wilink and ov2659 support for am437x-gp-evm
- Add am335x-evm bluetooth and mmc3 support
- Enable omap5-uevm uart wakeup interrupt
- Enable I2C2 on BeagleBone as it's used for the capes
- Use defines for LDP GPIO keys
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=MmxV
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.2/dt-pt1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Merge "Device tree related changes for omaps" from Tony Lindgren:
- Configure MMC data lines 4..8 for 1.8V IO on boards that
are using them as GPIOs instead of MMC data lines
- Add support for Baltos IR5221
- Add device tree support for LogicPD Torpedo devkit
- Add 3717 core pinctrl region
- Add gta04 1w and GSM audio support
- Add wilink and ov2659 support for am437x-gp-evm
- Add am335x-evm bluetooth and mmc3 support
- Enable omap5-uevm uart wakeup interrupt
- Enable I2C2 on BeagleBone as it's used for the capes
- Use defines for LDP GPIO keys
* tag 'omap-for-v4.2/dt-pt1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am335x-evm: add mmc3 and wlan definitions to dts
ARM: dts: Enable SDIO card interrupt for 37xx-evm
ARM: dts: Fix ldp gpio keys to use defines
ARM: dts: Beaglebone i2c definitions
ARM: dts: am437x-gp-evm: add DT nodes for ov2659 sensor
ARM: dts: add DTS for Baltos IR5221
ARM: dts: omap5-uevm: Add Uart wakeup interrupt
ARM: dts: omap3-gta04: Add GSM audio support
ARM: dts: am335x-evm: add bluetooth support
ARM: dts: am437x-gp-evm: add wilink8 support
ARM: dts: omap3-gta04: Add hdqw1 support
ARM: dts: add core2 padconf region for am3517
ARM: dts: Add minimal support for LogicPD Torpedo DM3730 devkit
ARM: OMAP3: Add support for configuring MMC pins as GPIO pins
Add support for Lightwriter SL50 series board, a small, robust and portable
Voice Output Communication Aids (VOCA) designed to meet the particular and
changing needs of people with speech loss resulting from a wide range of
acquired, progressive and congenital conditions.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Andy Simpkins <andy.simpkins@toby-churchill.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Support dm9000 network interface in the device tree of devkit8000 board.
Signed-off-by: Anthoine Bourgeois <anthoine.bourgeois@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Now that the arm_pmu framework is only used for CPU PMUs, there's no
reason to keep the pseudo-generic and CPU-specific framework portions
separate.
This patch folds the two into perf_event.c.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
[will: fixed up irq cfg to match upstream]
Signed-off-by: Will Deacon <will.deacon@arm.com>
Now that the core arm perf code maintains no global state and all
microarchitecture-specific PMU data can be fed in through the shared
probe function, it's possible to use it as a library and get rid of the
C file includes we have currently.
This patch factors out the ARMv7-specific portions out into the ARMv7
driver. For the moment this is always built if perf event support is
enabled, but the preprocessor guards will leave behind an empty file.
Now that perf_event_cpu.c contains no microarchitecture-specific data,
the associated probing code is removed, completing its relegation to a
library file. The vestigal "arm-pmu" platform device ID is removed in
this patch, as it has been unused since platform files were updated to
specify a more specific PMU variant.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Now that the core arm perf code maintains no global state and all
microarchitecture-specific PMU data can be fed in through the shared
probe function, it's possible to use it as a library and get rid of the
C file includes we have currently.
This patch factors out the ARMv6-specific portions out into the ARMv6
driver. For the moment this is always built if perf event support is
enabled, but the preprocessor guards will leave behind an empty file.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Now that the core arm perf code maintains no global state and all
microarchitecture-specific PMU data can be fed in through the shared
probe function, it's possible to use it as a library and get rid of the
C file includes we have currently.
This patch factors out the xscale-specific portions out into the xscale
driver. For the moment this is always built if perf event support is
enabled, but the preprocessor guards will leave behind an empty file.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Enable the probe function to be shared with other drivers, which will
inject the appropriate of_device_id and pmu_probe_info tables.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Currently the arm perf code has platdata callbacks for runtime PM and
irq handling, but no platform implements the hooks for the former. Kill
these off.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
We get a NULL pointer dereference on omap3 for thumb2 compiled kernels:
Internal error: Oops: 80000005 [#1] SMP THUMB2
...
[<c046497b>] (_raw_spin_unlock_irqrestore) from [<c0024375>]
(omap3_enter_idle_bm+0xc5/0x178)
[<c0024375>] (omap3_enter_idle_bm) from [<c0374e63>]
(cpuidle_enter_state+0x77/0x27c)
[<c0374e63>] (cpuidle_enter_state) from [<c00627f1>]
(cpu_startup_entry+0x155/0x23c)
[<c00627f1>] (cpu_startup_entry) from [<c06b9a47>]
(start_kernel+0x32f/0x338)
[<c06b9a47>] (start_kernel) from [<8000807f>] (0x8000807f)
The power management related assembly on omaps needs to interact with
ARM mode bootrom code, so we need to keep most of the related assembly
in ARM mode.
Turns out this error is because of missing ENDPROC for assembly code
as suggested by Stephen Boyd <sboyd@codeaurora.org>. Let's fix the
problem by adding ENDPROC in two places to sleep34xx.S.
Let's also remove the now duplicate custom code for mode switching.
This has been unnecessary since commit 6ebbf2ce43 ("ARM: convert
all "mov.* pc, reg" to "bx reg" for ARMv6+").
And let's also remove the comments about local variables, they are
now just confusing after the ENDPROC.
The reason why ENDPROC makes a difference is it sets .type and then
the compiler knows what to do with the thumb bit as explained at:
https://wiki.ubuntu.com/ARM/Thumb2PortingHowto
Reported-by: Kevin Hilman <khilman@kernel.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Move current sa11x0 IRQ driver to the irqchip subsystem.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Prepare for moving sa1100 irq driver to irqchip infrastructure - split
sa1100_init_irq into helper code and irq parts.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
So first of all, this atomic_scrub() function's naming is bad. It looks
like an atomic_t helper. Change it to edac_atomic_scrub().
The bigger problem is that this function is arch-specific and every new
arch which doesn't necessarily need that functionality still needs to
define it, otherwise EDAC doesn't compile.
So instead of doing that and including arch-specific headers, have each
arch define an EDAC_ATOMIC_SCRUB symbol which can be used in edac_mc.c
for ifdeffery. Much cleaner.
And we already are doing this with another symbol - EDAC_SUPPORT. This
is also much cleaner than having CONFIG_EDAC enumerate all the arches
which need/have EDAC support and drivers.
This way I can kill the useless edac.h header in tile too.
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Acked-by: Chris Metcalf <cmetcalf@ezchip.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Doug Thompson <dougthompson@xmission.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-edac@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linuxppc-dev@lists.ozlabs.org
Cc: "Maciej W. Rozycki" <macro@codesourcery.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: "Steven J. Hill" <Steven.Hill@imgtec.com>
Cc: x86@kernel.org
Signed-off-by: Borislav Petkov <bp@suse.de>
From: Ard Biesheuvel <ard.biesheuvel@linaro.org>
This patch registers hvc0 as the preferred console if no console
has been specified explicitly on the kernel command line.
The purpose is to allow platform agnostic kernels and boot images
(such as distro installers) to boot in a Xen/ARM domU without the
need to modify the command line by hand.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Reviewed-by: Julien Grall <julien.grall@linaro.org>
Currently, Xen is initialized/discovered in an initcall. This doesn't
allow us to support earlyprintk or choosing the preferred console when
running on Xen.
The current function xen_guest_init is now split in 2 parts:
- xen_early_init: Check if there is a Xen node in the device tree
and setup domain type
- xen_guest_init: Retrieve the information from the device node and
initialize Xen (grant table, shared page...)
The former is called in setup_arch, while the latter is an initcall.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Julien Grall <julien.grall@linaro.org>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Acked-by: Will Deacon <will.deacon@arm.com>
The function irq_of_parse_and_map returns 0 when the IRQ is not found.
Futhermore, move the check before notifying the user that we are running on
Xen.
Signed-off-by: Julien Grall <julien.grall@linaro.org>
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
The Mamba (like the OpenBlocks AX3) doesn't have a crystal
connected to the internal RTC - let's prevent the kernel from
probing it.
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Cc: <stable@vger.kernel.org> # v4.0 +
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This lets the function access the new memory slot without going through
kvm_memslots and id_to_memslot. It will simplify the code when more
than one address space will be supported.
Unfortunately, the "const"ness of the new argument must be casted
away in two places. Fixing KVM to accept const struct kvm_memory_slot
pointers would require modifications in pretty much all architectures,
and is left for later.
Reviewed-by: Radim Krcmar <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Use the new zynq binding for macb ethernet, since it will disable half
duplex gigabit like the Zynq TRM says to do. Also allow the compatible
cadence gem binding that won't disable half duplex but works otherwise.
Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com>
Acked-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
parallella - Remove linux,stdout-path.
Use stdout-path to identify kernel console
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Rafał Miłecki