Remove the downstream bus scaling code. It isn't needed for for
compatibility with a downstream or vendor kernel. Get it out of the
way to clear space for devfreq support.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Calling dev_pm_opp_find_freq_floor() returns the matched frequency
in 'freq'. We don't need to call dev_pm_opp_get_freq() again
to get the frequency value.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
We need to call dev_pm_opp_put() to put back the reference
for the OPP struct after calling the various dev_pm_opp_get_*
functions.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The msm/kms driver should work even if there is no GPU device specified
in DT. Currently, we get a NULL dereference crash in adreno_load_gpu
since the driver assumes that priv->gpu_pdev is non-NULL.
Perform an additional check on priv->gpu_pdev before trying to retrieve
the msm_gpu pointer from it.
v2: Incorporate Jordan's comments:
- Simplify the check to share the same error message.
- Use dev_err_once() to avoid an error message every time we open the
drm device fd.
Fixes: eec874ce5f (drm/msm/adreno: load gpu at probe/bind time)
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Acked-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
divider_recalc_rate() is an helper function used by clock divider of
different types, so the structure containing the 'hw' pointer is not
always a 'struct clk_divider'
At the following line:
> div = _get_div(table, val, flags, divider->width);
in several cases, the value of 'divider->width' is garbage as the actual
structure behind this memory is not a 'struct clk_divider'
Fortunately, this width value is used by _get_val() only when
CLK_DIVIDER_MAX_AT_ZERO flag is set. This has never been the case so
far when the structure is not a 'struct clk_divider'. This is probably
why we did not notice this bug before
Fixes: afe76c8fd0 ("clk: allow a clk divider with max divisor when zero")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Sylvain Lemieux <slemieux.tyco@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The fault recovery code tries to sync fences on all possible rings
instead of only the rings that actually exist which will fault the
kernel when the number of rings are less than the maximum amount.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
get_pages doesn't keep a reference of the pages allocated
when it fails later in the code path. This can lead to
a memory leak. Keep reference of the allocated pages so
that it can be freed when msm_gem_free_object gets called
later during cleanup.
Signed-off-by: Prakash Kamliya <pkamliya@codeaurora.org>
Signed-off-by: Sharat Masetty <smasetty@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
gcc-8 -fsanitize-coverage=trace-pc produces a false-positive warning:
drivers/gpu/drm/msm/mdp/mdp5/mdp5_plane.c: In function 'mdp5_plane_mode_set.isra.8':
drivers/gpu/drm/msm/mdp/mdp5/mdp5_plane.c:1053:3: error: 'crtc_x_r' may be used uninitialized in this function [-Werror=maybe-uninitialized]
It's relatively clear from reading the source that this cannot happen,
and older compilers get it right. This rearranges the code remove
the two affected variables, which reliably avoids the problem.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Rob Clark <robdclark@gmail.com>
No need to reinvent the wheel, we have bus_find_device_by_name().
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Rob Clark <robdclark@gmail.com>
* some a5xx files were missing
* fixup for an existing typo
Signed-off-by: Nicolas Dechesne <nicolas.dechesne@linaro.org>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The preferred location for Adreno firmware files is now in qcom/ subfolder,
especially now that we are adding some of them in linux-firmware.
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Nicolas Dechesne <nicolas.dechesne@linaro.org>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The prototype of msm_rd_dump_submit() has recently changed. However,
we have two declarations of this functions, and the other one
remains the old version, leading to this:
drivers/gpu/drm/msm/msm_gpu.c: In function 'recover_worker':
drivers/gpu/drm/msm/msm_gpu.c:295:23: error: passing argument 1 of 'msm_rd_dump_submit' from incompatible pointer type [-Werror=incompatible-pointer-types]
This changes the second one to match the first again.
Fixes: 2165e2b9cb ("drm/msm: split rd debugfs file")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Trivial fix to spelling mistake in DRM_DEV_ERROR error message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Rob Clark <robdclark@gmail.com>
This driver can use drm_fb_helper_lastclose() as its .lastclose callback.
It can also use drm_fb_helper_output_poll_changed() as its
.output_poll_changed callback.
Cc: Rob Clark <robdclark@gmail.com>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20171205182504.41923-7-noralf@tronnes.org
Cross-subsystem Changes:
- device tree doc for the Mitsubishi AA070MC01 and Tianma TM070RVHG71
panels (Lukasz Majewski) and for a 2nd endpoint on stm32 (Philippe Cornu)
Core Changes:
The most important changes are:
- Add drm_driver .last_close and .output_poll_changed helpers to reduce
fbdev emulation footprint in drivers (Noralf)
- Fix plane clipping in core and for vmwgfx (Ville)
Then we have a bunch of of improvement for print and debug such as the
addition of a framebuffer debugfs file. ELD connector, HDMI and
improvements. And a bunch of misc improvements, clean ups and style
changes and doc updates
[airlied: drop eld bits from amdgpu_dm]
Driver Changes:
- sii8620: filter unsupported modes and add DVI mode support (Maciej Purski)
- rockchip: analogix_dp: Remove unnecessary init code (Jeffy Chen)
- virtio, cirrus: add fb create_handle support to enable screenshots(Lepton Wu)
- virtio: replace reference/unreference with get/put (Aastha Gupta)
- vc4, gma500: Convert timers to use timer_setup() (Kees Cook)
- vc4: Reject HDMI modes with too high of clocks (Eric)
- vc4: Add support for more pixel formats (Dave Stevenson)
- stm: dsi: Rename driver name to "stm32-display-dsi" (Philippe Cornu)
- stm: ltdc: add a 2nd endpoint (Philippe Cornu)
- via: use monotonic time for VIA_WAIT_IRQ (Arnd Bergmann)
* tag 'drm-misc-next-2017-11-30' of git://anongit.freedesktop.org/drm/drm-misc: (96 commits)
drm/bridge: tc358767: add copyright lines
MAINTAINERS: change maintainer for Rockchip drm drivers
drm/vblank: Fix vblank timestamp debugs
drm/via: use monotonic time for VIA_WAIT_IRQ
dma-buf: Fix ifnullfree.cocci warnings
drm/printer: Add drm_vprintf()
drm/edid: Allow HDMI infoframe without VIC or S3D
video/hdmi: Allow "empty" HDMI infoframes
dma-buf/fence: Fix lock inversion within dma-fence-array
drm/sti: Handle return value of platform_get_irq_byname
drm/vc4: Add support for NV21 and NV61.
drm/vc4: Use .pixel_order instead of custom .flip_cbcr
drm/vc4: Add support for DRM_FORMAT_RGB888 and DRM_FORMAT_BGR888
drm: Move drm_plane_helper_check_state() into drm_atomic_helper.c
drm: Check crtc_state->enable rather than crtc->enabled in drm_plane_helper_check_state()
drm/vmwgfx: Try to fix plane clipping
drm/vmwgfx: Use drm_plane_helper_check_state()
drm/vmwgfx: Remove bogus crtc coords vs fb size check
gpu: gma500: remove unneeded DRIVER_LICENSE #define
drm: don't link DP aux i2c adapter to the hardware device node
...
Bake in the conflict between the drm_print.h extraction and the
addition of DRM_DEBUG_LEASES since we lost it a few too many times.
Also fix a new use of drm_plane_helper_check_state in msm to follow
Ville's conversion in
commit a01cb8ba3f
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Wed Nov 1 22:16:19 2017 +0200
drm: Move drm_plane_helper_check_state() into drm_atomic_helper.c
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drm_plane_helper_check_update() isn't a transitional helper, so let's
rename it to drm_atomic_helper_check_plane_state() and move it into
drm_atomic_helper.c.
v2: Fix the WARNs about plane_state->crtc matching crtc_state->crtc
Cc: Daniel Vetter <daniel@ffwll.ch>
Suggested-by: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171101201619.6175-1-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drm_plane_helper_check_state() is supposed to do things the atomic way,
so it should not be inspecting crtc->enabled. Rather we should be
looking at crtc_state->enable.
We have a slight complication due to drm_plane_helper_check_update()
reusing drm_plane_helper_check_state() for non-atomic drivers. Thus
we'll have to pass the crtc_state in manally and construct a fake
crtc_state in drm_plane_helper_check_update().
v2: Fix the WARNs about plane_state->crtc matching crtc_state->crtc
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171101201558.6059-1-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
-----BEGIN PGP SIGNATURE-----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=xVV2
-----END PGP SIGNATURE-----
Merge tag 'drm-for-v4.15' of git://people.freedesktop.org/~airlied/linux
Pull drm updates from Dave Airlie:
"This is the main drm pull request for v4.15.
Core:
- Atomic object lifetime fixes
- Atomic iterator improvements
- Sparse/smatch fixes
- Legacy kms ioctls to be interruptible
- EDID override improvements
- fb/gem helper cleanups
- Simple outreachy patches
- Documentation improvements
- Fix dma-buf rcu races
- DRM mode object leasing for improving VR use cases.
- vgaarb improvements for non-x86 platforms.
New driver:
- tve200: Faraday Technology TVE200 block.
This "TV Encoder" encodes a ITU-T BT.656 stream and can be found in
the StorLink SL3516 (later Cortina Systems CS3516) as well as the
Grain Media GM8180.
New bridges:
- SiI9234 support
New panels:
- S6E63J0X03, OTM8009A, Seiko 43WVF1G, 7" rpi touch panel, Toshiba
LT089AC19000, Innolux AT043TN24
i915:
- Remove Coffeelake from alpha support
- Cannonlake workarounds
- Infoframe refactoring for DisplayPort
- VBT updates
- DisplayPort vswing/emph/buffer translation refactoring
- CCS fixes
- Restore GPU clock boost on missed vblanks
- Scatter list updates for userptr allocations
- Gen9+ transition watermarks
- Display IPC (Isochronous Priority Control)
- Private PAT management
- GVT: improved error handling and pci config sanitizing
- Execlist refactoring
- Transparent Huge Page support
- User defined priorities support
- HuC/GuC firmware refactoring
- DP MST fixes
- eDP power sequencing fixes
- Use RCU instead of stop_machine
- PSR state tracking support
- Eviction fixes
- BDW DP aux channel timeout fixes
- LSPCON fixes
- Cannonlake PLL fixes
amdgpu:
- Per VM BO support
- Powerplay cleanups
- CI powerplay support
- PASID mgr for kfd
- SR-IOV fixes
- initial GPU reset for vega10
- Prime mmap support
- TTM updates
- Clock query interface for Raven
- Fence to handle ioctl
- UVD encode ring support on Polaris
- Transparent huge page DMA support
- Compute LRU pipe tweaks
- BO flag to allow buffers to opt out of implicit sync
- CTX priority setting API
- VRAM lost infrastructure plumbing
qxl:
- fix flicker since atomic rework
amdkfd:
- Further improvements from internal AMD tree
- Usermode events
- Drop radeon support
nouveau:
- Pascal temperature sensor support
- Improved BAR2 handling
- MMU rework to support Pascal MMU
exynos:
- Improved HDMI/mixer support
- HDMI audio interface support
tegra:
- Prep work for tegra186
- Cleanup/fixes
msm:
- Preemption support for a5xx
- Display fixes for 8x96 (snapdragon 820)
- Async cursor plane fixes
- FW loading rework
- GPU debugging improvements
vc4:
- Prep for DSI panels
- fix T-format tiling scanout
- New madvise ioctl
Rockchip:
- LVDS support
omapdrm:
- omap4 HDMI CEC support
etnaviv:
- GPU performance counters groundwork
sun4i:
- refactor driver load + TCON backend
- HDMI improvements
- A31 support
- Misc fixes
udl:
- Probe/EDID read fixes.
tilcdc:
- Misc fixes.
pl111:
- Support more variants
adv7511:
- Improve EDID handling.
- HDMI CEC support
sii8620:
- Add remote control support"
* tag 'drm-for-v4.15' of git://people.freedesktop.org/~airlied/linux: (1480 commits)
drm/rockchip: analogix_dp: Use mutex rather than spinlock
drm/mode_object: fix documentation for object lookups.
drm/i915: Reorder context-close to avoid calling i915_vma_close() under RCU
drm/i915: Move init_clock_gating() back to where it was
drm/i915: Prune the reservation shared fence array
drm/i915: Idle the GPU before shinking everything
drm/i915: Lock llist_del_first() vs llist_del_all()
drm/i915: Calculate ironlake intermediate watermarks correctly, v2.
drm/i915: Disable lazy PPGTT page table optimization for vGPU
drm/i915/execlists: Remove the priority "optimisation"
drm/i915: Filter out spurious execlists context-switch interrupts
drm/amdgpu: use irq-safe lock for kiq->ring_lock
drm/amdgpu: bypass lru touch for KIQ ring submission
drm/amdgpu: Potential uninitialized variable in amdgpu_vm_update_directories()
drm/amdgpu: potential uninitialized variable in amdgpu_vce_ring_parse_cs()
drm/amd/powerplay: initialize a variable before using it
drm/amd/powerplay: suppress KASAN out of bounds warning in vega10_populate_all_memory_levels
drm/amd/amdgpu: fix evicted VRAM bo adjudgement condition
drm/vblank: Tune drm_crtc_accurate_vblank_count() WARN down to a debug
drm/rockchip: add CONFIG_OF dependency for lvds
...
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJZ9kEFAAoJEHm+PkMAQRiGw6wH/0j197qyGd0hkVFMJO6LAgN3
KQWS4nZ5BkVDocwv0RVnUJTtXqU1eozFgdVEtSoaFXpzlHGuptR2Tau9efDCJ7w3
/utZxqvhGebZd2T+j+/o/LE8BRQxhADBNJq2D/o0WNt8ecxuG0GIkhkEYt/o3z1v
/sxlwVwzXB7Dc/h1WcgGJG7cS6L9KzzAzGAS/iNvdFrPOygHBv8c0MxVZIiBIeeK
1nZdyvbyM8uenSyG+prGt9ENrqXZxxfwUxIchi2V7A9m1WmD5zijNkf1JCWji/O+
UsA1auxna7MwoxjxqZuGm4MlKOwZ+8xutk4JGgc+aP/ulndJbJYu+4op/3vaFBM=
=Mhx+
-----END PGP SIGNATURE-----
Backmerge tag 'v4.14-rc7' into drm-next
Linux 4.14-rc7
Requested by Ben Skeggs for nouveau to avoid major conflicts,
and things were getting a bit conflicty already, esp around amdgpu
reverts.
The return type of ARRAY_SIZE() is size_t, so we have to use
%zu instead of %lu to avoid this warning:
drivers/gpu/drm/msm/msm_gpu.c: In function 'msm_gpu_init':
drivers/gpu/drm/msm/msm_gpu.c:742:31: error: format '%lu' expects argument of type 'long unsigned int', but argument 7 has type 'unsigned int' [-Werror=format=]
The warning it otherwise harmless as size_t is always the
same size as unsigned long in all supported architectures,
but gcc doesn't know that.
Fixes: c2fceabca6d5 ("drm/msm: Support multiple ringbuffers")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rob Clark <robdclark@gmail.com>
When a plane moves out of bounds (i.e, outside the crtc clip region), the
plane state's "visible" parameter changes to false. When this happens, we
(a) release the hwpipe resources away from it, and
(b) unstage the corresponding hwpipe(s) from the Layer Mixers in the CRTC.
(a) requires use to acquire the global atomic state and assign a new
hwpipe. (b) requires us to re-configure the Layer Mixer, which is done in
the CRTC. We don't want to do these things in the async plane update path,
so return an error if the new state's "visible" isn't the same as the
current state's "visible".
Cc: Gustavo Padovan <gustavo.padovan@collabora.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
MDP5 on newer SoCs support cursor planes (i.e, cursor SSPPs). They are a
separate entity unlike the cursors within LM.
Do not try to restore the MDP5 LM cursor registers, or the corresponding
CTL bits if we are not using LM cursors.
Also, since we've introduced a new variable 'lm_cursor_enabled', we can
now use it to avoid creating a different sets of crtc_funcs for CRTCs
with LM cursors and CRTCs with cursor planes.
Fixes: "drm/msm/mdp5: restore cursor state when enabling crtc"
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
We currently call mdp5_pipe_assign() twice to assign the left and right
hwpipes for our drm_plane. When merging 2 hwpipes, there are a few
constraints that we need to keep in mind:
- Only the same types of SSPPs are preferred. I.e, a RGB pipe should
be paired with another RGB pipe, VIG with VIG etc.
- The hwpipe staged on the left should have a higher priority than
the hwpipe staged on the right. The priorities are as follows:
VIG0 > VIG1 > VIG2 > VIG3
RGB0 > RGB1 > RGB2 > RGB3
DMA0 > DMA1
We can't apply these constraints easily if mdp5_pipe_assign() is
called twice. Update mdp5_pipe_assign() to find both hwpipes in
one go, and add the extra constraints needed.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
mdp5_pipe_assign currently returns the hwpipe pointer for the drm_plane.
Return it indirectly by setting a pointer passed as an argument. This
is needed because we want the func to find out the right hwpipe too.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
After converting legacy cursor updates to atomic async commits
mdp5_cursor_plane_funcs just duplicates mdp5_plane_funcs now.
Cc: Rob Clark <robdclark@gmail.com>
Cc: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.com>
Tested-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Add support to async updates of cursors by using the new atomic
interface for that. Basically what this commit does is do what
mdp5_update_cursor_plane_legacy() did but through atomic.
v5: call drm_atomic_helper_async_check() from the check hook
v4: add missing atomic async commit call to msm_atomic_commit(Archit Taneja)
v3: move size checks back to drivers (Ville Syrjälä)
v2: move fb setting to core and use new state (Eric Anholt)
Cc: Rob Clark <robdclark@gmail.com>
Cc: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.com>
Tested-by: Archit Taneja <architt@codeaurora.org> (v4)
[added comment about not hitting async update path if hwpipes are
re-assigned or global state is touched]
Signed-off-by: Rob Clark <robdclark@gmail.com>
Since we enabled runtime PM, we cannot count on cursor registers to
retain their values. This can result in situations where we think the
cursor is enabled when we enable the CRTC but it is trying to scan out
null (and the rest of cursor position/size is lost), resulting in faults
and generally angering the hw when coming out of DPMS with a cursor
enabled.
stable backport note: reverting 774e39ee35 is also a suitable fix
Fixes: 774e39ee35 drm/msm/mdp5: Set up runtime PM for MDSS
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
It's only likely to paper over bugs. Unlike the gpu, where we want to
keep things alive a bit longer in expectation of the next frame's
submit, when the display is shut down we can power off immediately.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Acked-by: Archit Taneja <architt@codeaurora.org>
Note we need to move update_fences() to after msm_rd_dump_submit(),
otherwise the bo's referenced by the submit may no longer be valid.
Signed-off-by: Rob Clark <robdclark@gmail.com>
We need this if we want to dump the submit after cleanup (ie. from hang
or fault). But in the backoff/unpin case we want to clear them. So add
a flag so we can skip clearing the IOVAs in at cleanup.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Split into two instances, the existing $debugfs/rd which continues to
dump all submits, and $debugfs/hangrd which will be used to dump just
submits that cause gpu hangs (and eventually faults, but that will
require some iommu framework enhancements).
Signed-off-by: Rob Clark <robdclark@gmail.com>
Prep work for adding a debugfs file that dumps just submits which
trigger hangs/faults. In this case the bo may already be in the
MADV_DONTNEED state, but will be still on the active list (since
the submit hasn't completed yet). So the normal check that the
bo is in the WILLNEED state does not apply. (But of course the bo
should definitely not be in the PURGED state!)
Signed-off-by: Rob Clark <robdclark@gmail.com>
Now that freedreno gallium driver defaults to using submit_queue task
(render reordering), just showing task->comm is not so useful (ie. it is
always "flush_queue:0"), so also dump the cmdline. This should also be
more useful for piglit/shader_runner.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Currently the rd dump avoids any buffers marked as WRITE under
the assumption that the contents are not interesting. While it
is true that the contents are uninteresting we should still print
the iova and size for all buffers so that any listening replay
tools can correctly construct the submission.
Print the header for all buffers but only dump the contents for
buffers marked as READ.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Recent changes to locking have rendered struct_mutex_task
unused.
Unused since 0e08270a1f.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Implement preemption for A5XX targets - this allows multiple
ringbuffers for different priorities with automatic preemption
of a lower priority ringbuffer if a higher one is ready.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
We use a global ringbuffer size and block size for all targets and
at least for 5XX preemption we need to know the value the RB_CNTL
in several locations so it makes sense to calculate it once and use
it everywhere.
The only monkey wrench is that we need to disable the RPTR shadow
for A430 targets but that only needs to be done once and doesn't
affect A5XX so we can or in the value at init time.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Add a shadow pointer to track the current command being written into
the ring. Don't commit it as 'cur' until the command is submitted.
Because 'cur' is used to construct the software copy of the wptr this
ensures that somebody peeking in on the ring doesn't assume that a
command is inflight while it is being written. This isn't a huge deal
with a single ring (though technically the hangcheck could assume
the system is prematurely busy when it isn't) but it will be rather
important for preemption where the decision to preempt is based
on a non-empty ringbuffer. Without a shadow an aggressive preemption
scheme could assume that the ringbuffer is non empty and switch to it
before the CPU is done writing the command and boom.
Even though preemption won't be supported for all targets because of
the way the code is organized it is simpler to make this generic for
all targets. The extra load for non-preemption targets should be
minimal.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
In order to manage ringbuffer priority to its fullest userspace
should know how many ringbuffers it has to work with. Add a
parameter to return the number of active rings.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Add the infrastructure to support the idea of multiple ringbuffers.
Assign each ringbuffer an id and use that as an index for the various
ring specific operations.
The biggest delta is to support legacy fences. Each fence gets its own
sequence number but the legacy functions expect to use a unique integer.
To handle this we return a unique identifier for each submission but
map it to a specific ring/sequence under the covers. Newer users use
a dma_fence pointer anyway so they don't care about the actual sequence
ID or ring.
The actual mechanics for multiple ringbuffers are very target specific
so this code just allows for the possibility but still only defines
one ringbuffer for each target family.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
When we move to multiple ringbuffers we're going to store the data
in the memptrs on a per-ring basis. In order to prepare for that
move the current memptrs from the adreno namespace into msm_gpu.
This is way cleaner and immediately lets us kill off some sub
functions so there is much less cost later when we do move to
per-ring structs.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Currently the behavior of a command stream is provided by the user
application during submission and the application is expected to internally
maintain the settings for each 'context' or 'rendering queue' and specify
the correct ones.
This works okay for simple cases but as applications become more
complex we will want to set context specific flags and do various
permission checks to allow certain contexts to enable additional
privileges.
Add kernel-side submit queues to be analogous to 'contexts' or
'rendering queues' on the application side. Each file descriptor
instance will maintain its own list of queues. Queues cannot be
shared between file descriptors.
For backwards compatibility context id '0' is defined as a default
context specifying no priority and no special flags. This is
intended to be the usual configuration for 99% of applications so
that a garden variety application can function correctly without
creating a queue. Only those applications requiring the specific
benefit of different queues need create one.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
We already have, as a result of upstreaming the gpu bindings,
msm_clk_get() which will try to get the clock both without and with a
"_clk" suffix. Use this in HDMI code so we can drop the "_clk" suffix
in bindings while maintaing backwards compatibility.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
We already have, as a result of upstreaming the gpu bindings,
msm_clk_get() which will try to get the clock both without and with a
"_clk" suffix. Use this in eDP code so we can drop the "_clk" suffix
in bindings while maintaing backwards compatibility.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
We already have, as a result of upstreaming the gpu bindings,
msm_clk_get() which will try to get the clock both without and with a
"_clk" suffix. Use this in DSI code so we can drop the "_clk" suffix
in bindings while maintaing backwards compatibility.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
When firmware was added to linux-firmware, it was put in a qcom sub-
directory, unlike what we'd been using before. For a300_pfp.fw and
a300_pm4.fw symlinks were created, but we'd prefer not to have to do
this in the future. So add support to look in both places when
loading firmware.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Previously, in an effort to defer initializing the gpu until firmware
was available (ie. rootfs mounted), the gpu was not loaded at when the
subdevice was bound. Which resulted that clks/etc were requested in a
place that devm couldn't really help unwind if something failed.
Instead move request_firmware() to gpu->hw_init() and construct the gpu
earlier in adreno_bind(). To avoid the rest of the driver needing to
be aware of a gpu that hasn't managed to load firmware and hw_init()
yet, stash the gpu ptr in the adreno device's drvdata, and don't set
priv->gpu() until hw_init() succeeds.
Signed-off-by: Rob Clark <robdclark@gmail.com>
This was used as a placeholder. It was never really input to the MDSS/HDMI
clocks.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
We need to call reservation_object_reserve_shared() in both cases, but
this wasn't happening in the _NO_IMPLICIT submit case.
Fixes: f0a42bb ("drm/msm: submit support for in-fences")
Reported-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
We need to call reservation_object_reserve_shared() in both cases, but
this wasn't happening in the _NO_IMPLICIT submit case.
Fixes: f0a42bb ("drm/msm: submit support for in-fences")
Reported-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
While converting mdp5_enable/disable() calls to pm_runtime_get/put() API,
an extra call to pm_runtime_put_autosuspend() crept in
mdp5_crtc_cursor_set(). This results in calling the suspend handler
twice, and therefore clk_disables twice, which isn't a nice thing to do.
Fixes: d68fe15b18 (drm/msm/mdp5: Use runtime PM get/put API instead ...)
Reported-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The DSI runtime PM suspend/resume callbacks check whether
msm_host->cfg_hnd is non-NULL before trying to enable the bus clocks.
This is done to accommodate early calls to these functions that may
happen before the bus clocks are even initialized.
Calling pm_runtime_put_autosuspend() in dsi_host_init() can result in
racy behaviour since msm_host->cfg_hnd is set very soon after. If the
suspend callback happens too late, we end up trying to disable clocks
that were never enabled, resulting in a bunch of WARN_ON splats.
Use pm_runtime_put_sync() so that the suspend callback is called
immediately.
Reported-by: Nicolas Dechesne <nicolas.dechesne@linaro.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
In case of error, the function msm_gem_get_vaddr() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check should
be replaced with IS_ERR().
Fixes: 8223286d62 ("drm/msm: Add a helper function for in-kernel
buffer allocations")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Rob Clark <robdclark@gmail.com>
pipe is an unsigned int and less than zero comparison for unsigned
values is always false.
Detected using the following cocci script:
@@
unsigned int i;
@@
* i < 0
Signed-off-by: Aishwarya Pant <aishpant@gmail.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20171010184207.iv3dinrtwvbv7fei@aishwarya
GFP_TEMPORARY was introduced by commit e12ba74d8f ("Group short-lived
and reclaimable kernel allocations") along with __GFP_RECLAIMABLE. It's
primary motivation was to allow users to tell that an allocation is
short lived and so the allocator can try to place such allocations close
together and prevent long term fragmentation. As much as this sounds
like a reasonable semantic it becomes much less clear when to use the
highlevel GFP_TEMPORARY allocation flag. How long is temporary? Can the
context holding that memory sleep? Can it take locks? It seems there is
no good answer for those questions.
The current implementation of GFP_TEMPORARY is basically GFP_KERNEL |
__GFP_RECLAIMABLE which in itself is tricky because basically none of
the existing caller provide a way to reclaim the allocated memory. So
this is rather misleading and hard to evaluate for any benefits.
I have checked some random users and none of them has added the flag
with a specific justification. I suspect most of them just copied from
other existing users and others just thought it might be a good idea to
use without any measuring. This suggests that GFP_TEMPORARY just
motivates for cargo cult usage without any reasoning.
I believe that our gfp flags are quite complex already and especially
those with highlevel semantic should be clearly defined to prevent from
confusion and abuse. Therefore I propose dropping GFP_TEMPORARY and
replace all existing users to simply use GFP_KERNEL. Please note that
SLAB users with shrinkers will still get __GFP_RECLAIMABLE heuristic and
so they will be placed properly for memory fragmentation prevention.
I can see reasons we might want some gfp flag to reflect shorterm
allocations but I propose starting from a clear semantic definition and
only then add users with proper justification.
This was been brought up before LSF this year by Matthew [1] and it
turned out that GFP_TEMPORARY really doesn't have a clear semantic. It
seems to be a heuristic without any measured advantage for most (if not
all) its current users. The follow up discussion has revealed that
opinions on what might be temporary allocation differ a lot between
developers. So rather than trying to tweak existing users into a
semantic which they haven't expected I propose to simply remove the flag
and start from scratch if we really need a semantic for short term
allocations.
[1] http://lkml.kernel.org/r/20170118054945.GD18349@bombadil.infradead.org
[akpm@linux-foundation.org: fix typo]
[akpm@linux-foundation.org: coding-style fixes]
[sfr@canb.auug.org.au: drm/i915: fix up]
Link: http://lkml.kernel.org/r/20170816144703.378d4f4d@canb.auug.org.au
Link: http://lkml.kernel.org/r/20170728091904.14627-1-mhocko@kernel.org
Signed-off-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Mel Gorman <mgorman@suse.de>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Neil Brown <neilb@suse.de>
Cc: "Theodore Ts'o" <tytso@mit.edu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Updates for 4.14.. I have some further patches from Jordan to add
multiple priority levels and pre-emption, but those will probably be
for 4.15 to give me time for the mesa parts.
* tag 'drm-msm-next-2017-08-22' of git://people.freedesktop.org/~robclark/linux:
drm/msm/mdp5: mark runtime_pm functions as __maybe_unused
drm/msm: remove unused variable
drm/msm/mdp5: make helper function static
drm/msm: make msm_framebuffer_init() static
drm/msm: add helper to allocate stolen fb
drm/msm: don't track fbdev's gem object separately
drm/msm: add modeset module param
drm/msm/mdp5: add tracking for clk enable-count
drm/msm: remove unused define
drm/msm: Add a helper function for in-kernel buffer allocations
drm/msm: Attach the GPU MMU when it is created
drm/msm: Add A5XX hardware fault detection
drm/msm: Remove uneeded platform dev members
drm/msm/mdp5: Set up runtime PM for MDSS
drm/msm/mdp5: Write to SMP registers even if allocations don't change
drm/msm/mdp5: Don't use mode_set helper funcs for encoders and CRTCs
drm/msm/dsi: Implement RPM suspend/resume callbacks
drm/msm/dsi: Set up runtime PM for DSI
drm/msm/hdmi: Set up runtime PM for HDMI
drm/msm/mdp5: Use runtime PM get/put API instead of toggling clocks
When CONFIG_PM is disabled, we get harmless warnings about unused
functions:
drivers/gpu/drm/msm/mdp/mdp5/mdp5_kms.c:1025:12: error: 'mdp5_runtime_resume' defined but not used [-Werror=unused-function]
static int mdp5_runtime_resume(struct device *dev)
^~~~~~~~~~~~~~~~~~~
drivers/gpu/drm/msm/mdp/mdp5/mdp5_kms.c:1015:12: error: 'mdp5_runtime_suspend' defined but not used [-Werror=unused-function]
static int mdp5_runtime_suspend(struct device *dev)
^~~~~~~~~~~~~~~~~~~~
This marks both functions as __maybe_unused so the compiler
can drop them silently.
Fixes: d68fe15b18 ("drm/msm/mdp5: Use runtime PM get/put API instead of toggling clocks")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rob Clark <robdclark@gmail.com>
A cleanup left behind an unused variable that we have to remove
in order to avoid this harmless warning:
drivers/gpu/drm/msm/adreno/a5xx_gpu.c: In function 'a5xx_zap_shader_init':
drivers/gpu/drm/msm/adreno/a5xx_gpu.c:493:19: error: unused variable 'a5xx_gpu' [-Werror=unused-variable]
Fixes: 8d6f08272b ("drm/msm: Remove uneeded platform dev members")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rob Clark <robdclark@gmail.com>
We'll later want to re-use this for state-readback when bootloader
enables display, so that we can create an fb for the initial
plane->state->fb.
Signed-off-by: Rob Clark <robdclark@gmail.com>
The drm_framebuffer is refcnt'd these days and will unref the underlying
bo as needed. So we can simplify a little.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Accessing registers for an unclocked block is an insta-reboot on
snapdragon devices. So add a bit of logic to track the enable_count so
we can WARN_ON() unclocked register writes. This makes it much easier
to track down mistakes.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Nearly all of the buffer allocations for kernel allocate an buffer object,
virtual address and GPU iova at the same time. Make a helper function to
handle the details.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
[dropped msm_fbdev conversion to new helper, since it interferes with
display-handover work, where we want to separate allocation and mapping]
Signed-off-by: Rob Clark <robdclark@gmail.com>
Currently the GPU MMU is attached in the adreno_gpu code but as
more and more of the GPU initialization moves to the generic
GPU path we have a need to map and use GPU memory earlier and
earlier. There isn't any reason to defer attaching the MMU
until later so attach it right after the address space is
created so it can be used immediately.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
UAPI Changes:
- vc4: Allow userspace to dictate rendering order in submit_cl ioctl (Eric)
Cross-subsystem Changes:
- vboxvideo: One of Cihangir's patches applies to vboxvideo which is maintained
in staging
Core Changes:
- atomic_legacy_backoff is officially killed (Daniel)
- Extract drm_device.h (Daniel)
- Unregister drm device on unplug (Daniel)
- Rename deprecated drm_*_(un)?reference functions to drm_*_{get|put} (Cihangir)
Driver Changes:
- vc4: Error/destroy path cleanups, log level demotion, edid leak (Eric)
- various: Make various drm_*_funcs structs const (Bhumika)
- tinydrm: add support for LEGO MINDSTORMS EV3 LCD (David)
- various: Second half of .dumb_{map_offset|destroy} defaults set (Noralf)
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Eric Anholt <eric@anholt.net>
Cc: Bhumika Goyal <bhumirks@gmail.com>
Cc: Cihangir Akturk <cakturk@gmail.com>
Cc: David Lechner <david@lechnology.com>
Cc: Noralf Trønnes <noralf@tronnes.org>
* tag 'drm-misc-next-2017-08-16' of git://anongit.freedesktop.org/git/drm-misc: (50 commits)
drm/gem-cma-helper: Remove drm_gem_cma_dumb_map_offset()
drm/virtio: Use the drm_driver.dumb_destroy default
drm/bochs: Use the drm_driver.dumb_destroy default
drm/mgag200: Use the drm_driver.dumb_destroy default
drm/exynos: Use .dumb_map_offset and .dumb_destroy defaults
drm/msm: Use the drm_driver.dumb_destroy default
drm/ast: Use the drm_driver.dumb_destroy default
drm/qxl: Use the drm_driver.dumb_destroy default
drm/udl: Use the drm_driver.dumb_destroy default
drm/cirrus: Use the drm_driver.dumb_destroy default
drm/tegra: Use .dumb_map_offset and .dumb_destroy defaults
drm/gma500: Use .dumb_map_offset and .dumb_destroy defaults
drm/mxsfb: Use .dumb_map_offset and .dumb_destroy defaults
drm/meson: Use .dumb_map_offset and .dumb_destroy defaults
drm/kirin: Use .dumb_map_offset and .dumb_destroy defaults
drm/vc4: Continue the switch to drm_*_put() helpers
drm/vc4: Fix leak of HDMI EDID
dma-buf: fix reservation_object_wait_timeout_rcu to wait correctly v2
dma-buf: add reservation_object_copy_fences (v2)
drm/tinydrm: add support for LEGO MINDSTORMS EV3 LCD
...
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJZkNpUAAoJEHm+PkMAQRiGr68H/2nr8kxpoUhZ7eA5C71waCjh
gnJSevkzJAp+fCb0KfQFAp1qvpmLLle4e6tAxYgTQZg4Z3W5cJJNfxu9TzY5sGuL
o9QUr43XzABepW4e4jhRtZv6dj3K6XruNeDQKXDZTDcc/S8zoiS/Pltq7VgPcAuM
kX+3qsNdUyknngD6b0z9NtJkb0mHKY6J8MpraWRO34egDwsaN/tuhRj0DRQpCoyQ
x/k+hMbc9MB9Dn8cfACo6Omb+r5Rfd7dTBUAju/TnIIgs//9voHba307N7XvLJZg
kWc8MqMQQZXfRZHB0atpDMHyZS/XQRlNPXj76j0+Ud/byODKTFkkazmgTpALvj8=
=CxeU
-----END PGP SIGNATURE-----
Backmerge tag 'v4.13-rc5' into drm-next
Linux 4.13-rc5
There's a really nasty nouveau collision, hopefully someone can take a look
once I pushed this out.
It's dead code, the core handles all this directly now.
The only special case is nouveau and tda988x which used one function
for both legacy modeset code and -nv50 atomic world instead of 2
vtables. But amounts to exactly the same.
v2: Rebase over the panel/brideg refactorings in stm/ltdc.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Peter Senna Tschudin <peter.senna@collabora.com>
Cc: Martin Donnelly <martin.donnelly@ge.com>
Cc: Martyn Welch <martyn.welch@collabora.co.uk>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: David Airlie <airlied@linux.ie>
Cc: Inki Dae <inki.dae@samsung.com>
Cc: Joonyoung Shim <jy0922.shim@samsung.com>
Cc: Seung-Woo Kim <sw0312.kim@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Alison Wang <alison.wang@freescale.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: CK Hu <ck.hu@mediatek.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Carlo Caione <carlo@caione.org>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: Mark Yao <mark.yao@rock-chips.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Cc: Vincent Abriou <vincent.abriou@st.com>
Cc: Yannick Fertre <yannick.fertre@st.com>
Cc: Philippe Cornu <philippe.cornu@st.com>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Cc: Jeffy Chen <jeffy.chen@rock-chips.com>
Cc: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Cc: Yakir Yang <kuankuan.y@gmail.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Jose Abreu <Jose.Abreu@synopsys.com>
Cc: Romain Perier <romain.perier@collabora.com>
Cc: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Cc: Xinliang Liu <z.liuxinliang@hisilicon.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Rongrong Zou <zourongrong@gmail.com>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Hai Li <hali@codeaurora.org>
Cc: "Noralf Trønnes" <noralf@tronnes.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: intel-gfx@lists.freedesktop.org
Cc: linux-mediatek@lists.infradead.org
Cc: linux-amlogic@lists.infradead.org
Cc: nouveau@lists.freedesktop.org
Cc: linux-renesas-soc@vger.kernel.org
Cc: linux-rockchip@lists.infradead.org
Cc: linux-tegra@vger.kernel.org
Cc: virtualization@lists.linux-foundation.org
Cc: zain wang <wzz@rock-chips.com>
Cc: Baoyou Xie <baoyou.xie@linaro.org>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170725080122.20548-8-daniel.vetter@ffwll.ch
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Archit Taneja <architt@codeaurora.org>
Tested-by: Philippe Cornu <philippe.cornu@st.com> (on stm)
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Acked-by: Noralf Trønnes <noralf@tronnes.org>
Acked-by: Vincent Abriou <vincent.abriou@st.com>
It's dead code because this is now handled in the core.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: David Airlie <airlied@linux.ie>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Eric Engestrom <eric@engestrom.ch>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: "Ville Syrjälä" <ville.syrjala@linux.intel.com>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Philippe Cornu <philippe.cornu@st.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Sushmita Susheelendra <ssusheel@codeaurora.org>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: intel-gfx@lists.freedesktop.org
Cc: nouveau@lists.freedesktop.org
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Thomas Hellstrom <thellstrom@vmware.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170725080122.20548-5-daniel.vetter@ffwll.ch
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Acked-by: Philippe Cornu <philippe.cornu@st.com>
Tested-by: Philippe Cornu <philippe.cornu@st.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Acked-by: Thomas Hellstrom <thellstrom@vmware.com>
The A5XX GPU has really good hardware fault detection that can
detect a abnormal hardware condition and fire an interrupt in
a matter of milliseconds which is a lot better than waiting for
the hangcheck timer.
Enable the interrupt and log information before kicking off
recovery.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Commit eeb754746b ("drm/msm/gpu: use pm-runtime") adds a pointer
for the GPU platform device to the msm_gpu struct so we can
happily remove the same pointers from the individual GPU
structs.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
MDSS represents the top level wrapper that contains MDP5, DSI, HDMI and
other sub-blocks. W.r.t device heirarchy, it's the parent of all these
devices. The power domain of this device is actually tied to the GDSC
hw. When any sub-device enables its PD, MDSS's PD is also enabled.
The suspend/resume ops enable the top level clocks that end at the MDSS
boundary. For now, we're letting them all be optional, since the child
devices anyway hold a ref to these clocks.
Until now, we'd called a runtime_get() during probe, which ensured that
the GDSC was always on. Now that we've set up runtime PM for the children
devices, we can get rid of this hack.
Note: that the MDSS device is the platform_device in msm_drv.c. The
msm_runtime_suspend/resume ops call the funcs that enable/disable
the top level MDSS clocks. This is different from MDP4, where the
platform device created in msm_drv.c represents MDP4 itself. It would
have been nicer to hide these differences by adding new kms funcs, but
runtime PM needs to be enabled before kms is set up (i.e, msm_kms_init
is called).
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Requests for assigning/freeing SMP blocks by planes are collected during
the atomic check phase, and represented by mdp5_smp_state's 'assigned'
and 'released' members.
Once the atomic state is committed, these members are reset to 0,
indicating that the existing configuration satisfies all the planes.
Future atomic commits will copy the old mdp5_smp_state, and the 'assigned'
and 'released' members would be updated only if there was a change in
the plane configurations.
When we disable and re-enable display, we lose the values we wrote to the
SMP registers, but the code doesn't program the registers because there
isn't any change in mdp5_smp_state.
Fix this by writing to the registers irrespective of whether there was
a change in SMP state or not. We do this by keeping a cache of the
register values, and write them every time we commit a state.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
We shouldn't use use mode_set/mode_set_nofb helpers when we use runtime
PM. The registers configured in these funcs lose their state when we
eventually enable the display pipeline.
Do not implement these vfuncs in the helpers, and call them in the
crtc_enable/encoder_enable paths instead.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The bus clocks are always enabled/disabled along with the power
domain, so move it to the runtime suspend/resume ops. This cleans
up the clock code a bit. Get rid of the clk_mutex mutex since it
isn't needed.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Call the pm_runtime_get/put API where we need the clocks enabled.
The main entry/exit points are 1) enabling/disabling the DSI bridge
and 2) Sending commands from the DSI host to the device.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Enable rudimentary runtime PM in the HDMI driver. We can't really do
agressive PM toggling at the moment because we need to leave the hpd
clocks enabled all the time. There isn't much benefit of creating
suspend/resume ops to toggle clocks either.
We just make sure that we configure the power domain in the HDMI bridge's
enable/disable paths, and the HDMI connector's detect() op.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
mdp5_enable/disable calls are scattered all around in the MDP5 code.
Use the pm_runtime_get/put calls here instead, and populate the
runtime PM suspend/resume ops to manage the clocks.
About the overall design: MDP5 is a child of the top level MDSS
device. MDSS is also the parent to DSI, HDMI and other interfaces. When
we enable MDP5's power domain, we end up enabling MDSS's PD too. It is
only MDSS's PD that actually controlls the GDSC HW. Therefore, calling
runtime_get/put on the MDP5 device is like just requesting a vote to
enable/disable the GDSC.
Functionally, replacing the clock enable/disable calls with the RPM API
can result in the power domain (GDSC) state being toggled if no other
child isn't powered on. This can result in the register context being lost.
We make sure (in future commits) that code paths don't end up configuring
registers and then later lose state, resulting in a bad HW state.
For now, we've replaced each mdp5_enable/disable with runtime_get/put API.
We could optimize things later by removing runtime_get/put calls which
don't really need to be there. This could prevent unnecessary toggling of
the power domain and clocks.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
In zap_shader_load_mdt(), we pass a pointer to a phys_addr_t
into dmam_alloc_coherent, which the compiler warns about:
drivers/gpu/drm/msm/adreno/a5xx_gpu.c: In function 'zap_shader_load_mdt':
drivers/gpu/drm/msm/adreno/a5xx_gpu.c:54:50: error: passing argument 3 of 'dmam_alloc_coherent' from incompatible pointer type [-Werror=incompatible-pointer-types]
The returned DMA address is later passed on to a function that
takes a phys_addr_t, so it's clearly wrong to use the DMA
mapping interface here: the memory may be uncached, or the
address may be completely wrong if there is an IOMMU connected
to the device. What the code actually wants to do is to get
the physical address from the reserved-mem node. It goes through
the dma-mapping interfaces for obscure reasons, and this
apparently only works by chance, relying on specific bugs
in the error handling of the arm64 dma-mapping implementation.
The same problem existed in the "venus" media driver, which was
now fixed by Stanimir Varbanov after long discussions.
In order to make some progress here, I have now ported his
approach over to the adreno driver. The patch is currently
untested, and should get a good review, but it is now much
simpler than the original, and it should be obvious what
goes wrong if I made a mistake in the port.
See also: a6e2d36bf6 ("media: venus: don't abuse dma_alloc for non-DMA allocations")
Cc: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Fixes: 7c65817e6d ("drm/msm: gpu: Enable zap shader for A5XX")
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-and-Tested-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rob Clark <robdclark@gmail.com>
When compile-testing for something other than ARCH_QCOM,
we run into a link error:
drivers/gpu/drm/msm/adreno/a5xx_gpu.o: In function `a5xx_hw_init':
a5xx_gpu.c:(.text.a5xx_hw_init+0x600): undefined reference to `qcom_mdt_get_size'
a5xx_gpu.c:(.text.a5xx_hw_init+0x93c): undefined reference to `qcom_mdt_load'
There is already an #ifdef that tries to check for CONFIG_QCOM_MDT_LOADER,
but that symbol is only meaningful when building for ARCH_QCOM.
This adds a compile-time check for ARCH_QCOM, and clarifies the
Kconfig select statement so we don't even try it for other targets.
The check for CONFIG_QCOM_MDT_LOADER can then go away, which also
improves compile-time coverage and makes the code a little nicer
to read.
Fixes: 7c65817e6d ("drm/msm: gpu: Enable zap shader for A5XX")
Acked-by: Jordan Crouse <jcrouse@codeaurora.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rob Clark <robdclark@gmail.com>
msm_gpu's get_timestamp() op (called by the MSM_GET_PARAM ioctl) can
result in register accesses. We need our power domain and clocks to
be active for that. Make sure they are enabled here.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Fix a typo in msm_ioctl_gem_submit - check args->flags for the
MSM_SUBMIT_NO_IMPLICIT flag instead of args->fence.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
On A5XX GPU hardware clock gating needs to be turned off before
reading certain GPU registers via AHB. Turn off HWCG before calling
adreno_show() to safely dump all the registers without a system hang.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
There are some use cases wherein we need to turn off hardware clock
gating before reading certain registers. Modify the A5XX HWCG function
to allow user to enable or disable clock gating at will.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The 0xf400 and 0xf800 ranges are in the RBBM_SECVID block which may
be protected from CPU access. Skip dumping them since they are minimally
useful for debugging and they aren't worth a system hang.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
We have upstream bindings (msm8916) that have the "_clk" suffix in the
clock names. The downstream bindings also require it.
We want to drop the "_clk" suffix and at the same time support existing
bindings. Update the MDP5 code with the the msm_clk_get() helper to
support both old and new clock names.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The mdp5_cmd_encoder_disable is accidentally called in the encoder enable
path. We've not seen any problems since we haven't tested with command
mode panels in a while. Fix the copy-paste error.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
After the commit mentioned below, we start computing the byte and pixel
clocks (dsi_calc_clk_rate) in the DSI bridge's mode_set() op. The
calculation involves the number of DSI lanes being used by the
downstream bridge/panel.
If the downstream bridge/panel tries to change the number of DSI lanes
(as done in the ADV7533 driver) in its mode_set() op, then our DSI
host driver will not have the correct number of lanes when computing
byte/pixel clocks.
Fix this by delaying the clock rate calculation in the DSI bridge
enable path. In particular, compute the clock rates in
msm_dsi_host_get_phy_clk_req().
This fixes the DSI host error interrupts seen when we try to switch
between modes that require different number of lanes (4 to 3 lanes, or
vice versa) on db410c. The error interrupts occur since the byte/pixel
clock rates aren't according to what the DSI video mode timing engine
expects.
Fixes: b62aa70a98 ("drm/msm/dsi: Move PHY operations out of host")
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
We recently added locking to this function but there was a direct return
that was overlooked where we need to unlock.
Fixes: 0e08270a1f ("drm/msm: Separate locking of buffer resources from struct_mutex")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Rob Clark <robdclark@gmail.com>
We recently added an integer overflow check but it needs an additional
tweak to work properly on 32 bit systems.
The problem is that we're doing the right hand side of the assignment as
type unsigned long so the max it will have an integer overflow instead
of being larger than SIZE_MAX. That means the "sz > SIZE_MAX" condition
is never true even on 32 bit systems. We need to first cast it to u64
and then do the math.
Fixes: 4a630fadbb ("drm/msm: Fix potential buffer overflow issue")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Following compilation warnings were observed for these files:
CC [M] drivers/gpu/drm/msm/mdp/mdp5/mdp5_mdss.o
drivers/gpu/drm/msm/mdp/mdp5/mdp5_crtc.c: In function 'blend_setup':
drivers/gpu/drm/msm/mdp/mdp5/mdp5_crtc.c:223:7: warning: missing braces around initializer [-Wmissing-braces]
enum mdp5_pipe stage[STAGE_MAX + 1][MAX_PIPE_STAGE] = { SSPP_NONE };
^
drivers/gpu/drm/msm/mdp/mdp5/mdp5_crtc.c:223:7: warning: (near initialization for 'stage[0]') [-Wmissing-braces]
drivers/gpu/drm/msm/mdp/mdp5/mdp5_crtc.c:224:7: warning: missing braces around initializer [-Wmissing-braces]
enum mdp5_pipe r_stage[STAGE_MAX + 1][MAX_PIPE_STAGE] = { SSPP_NONE };
^
drivers/gpu/drm/msm/mdp/mdp5/mdp5_crtc.c:224:7: warning: (near initialization for 'r_stage[0]') [-Wmissing-braces]
drivers/gpu/drm/msm/mdp/mdp5/mdp5_plane.c: In function 'mdp5_plane_mode_set':
drivers/gpu/drm/msm/mdp/mdp5/mdp5_plane.c:892:9: warning: missing braces around initializer [-Wmissing-braces]
struct phase_step step = { 0 };
^
drivers/gpu/drm/msm/mdp/mdp5/mdp5_plane.c:892:9: warning: (near initialization for 'step.x') [-Wmissing-braces]
drivers/gpu/drm/msm/mdp/mdp5/mdp5_plane.c:893:9: warning: missing braces around initializer [-Wmissing-braces]
struct pixel_ext pe = { 0 };
^
drivers/gpu/drm/msm/mdp/mdp5/mdp5_plane.c:893:9: warning: (near initialization for 'pe.left') [-Wmissing-braces]
This happens because in the first case we were initializing a two
dimensional array with {0} and in the second case we were initializing a
struct containing two arrays with {0}.
Fix them by adding another pair of {}.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
This is the plumbing for supporting fb modifiers on planes. Modifiers
have already been introduced to some extent, but this series will extend
this to allow querying modifiers per plane. Based on this, the client to
enable optimal modifications for framebuffers.
This patch simply allows the DRM drivers to initialize their list of
supported modifiers upon initializing the plane.
v2: A minor addition from Daniel
v3:
* Updated commit message
* s/INVALID/DRM_FORMAT_MOD_INVALID (Liviu)
* Remove some excess newlines (Liviu)
* Update comment for > 64 modifiers (Liviu)
v4: Minor comment adjustments (Liviu)
v5: Some new platforms added due to rebase
v6: Add some missed plane inits (or maybe they're new - who knows at
this point) (Daniel)
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Daniel Stone <daniels@collabora.com> (v2)
Reviewed-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Daniel Stone <daniels@collabora.com>
for_each_obj_in_state is about to be removed, so convert
to the new iterator macros.
Just like in omap, use crtc_state->active instead of
crtc_state->enable when waiting for completion.
Changes since v1:
- Fix compilation.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Vincent Abriou <vincent.abriou@st.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Rob Herring <robh@kernel.org>
Cc: Markus Elfring <elfring@users.sourceforge.net>
Cc: Sushmita Susheelendra <ssusheel@codeaurora.org>
Cc: linux-arm-msm@vger.kernel.org
Cc: freedreno@lists.freedesktop.org
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Tested-by: Archit Taneja <architt@codeaurora.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20170719143920.25685-6-maarten.lankhorst@linux.intel.com
drm_atomic_helper_swap_state() will be changed to interruptible waiting
in the next few commits, so all drivers have to be changed to handling
failure.
MSM has its own busy tracking, which means the swap_state call can be
done with stall = false, in which case it should never return an error.
Handle failure with BUG_ON for this reason.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Rob Clark <robdclark@gmail.com>
Cc: linux-arm-msm@vger.kernel.org
Cc: freedreno@lists.freedesktop.org
Link: http://patchwork.freedesktop.org/patch/msgid/20170711143314.2148-8-maarten.lankhorst@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Tested-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
- FBINFO_CAN_FORCE_OUTPUT has been a lie ever since we nerfed&removed
the entire panic handling code in our fbdev emulation. We might
restore kms panic output, but not through the bazillion of legacy
code layers called fbdev/fbcon, there's just no way to make that
work safely.
- With the module check change FBINFO_DEFAULT is always 0, so can be
removed too.
That removes another change to cargo-cult stuff in kms drivers, yay!
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170706125735.28299-5-daniel.vetter@ffwll.ch
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
HDMI 1.4b support the CEA video modes as per range of CEA-861-D (VIC 1-64).
For any other mode, the VIC filed in AVI infoframes should be 0.
HDMI 2.0 sinks, support video modes range as per CEA-861-F spec, which is
extended to (VIC 1-107).
This patch adds a bool input variable, which indicates if the connected
sink is a HDMI 2.0 sink or not. This will make sure that we don't pass a
HDMI 2.0 VIC to a HDMI 1.4 sink.
This patch touches all drm drivers, who are callers of this function
drm_hdmi_avi_infoframe_from_display_mode but to make sure there is
no change in current behavior, is_hdmi2 is kept as false.
In case of I915 driver, this patch:
- checks if the connected display is HDMI 2.0.
- HDMI infoframes carry one of this two type of information:
- VIC for 4K modes for HDMI 1.4 sinks
- S3D information for S3D modes
As CEA-861-F has already defined VICs for 4K videomodes, this
patch doesn't allow sending HDMI infoframes for HDMI 2.0 sinks,
until the mode is 3D.
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Jose Abreu <jose.abreu@synopsys.com>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
PS: This patch touches a few lines in few files, which were
already above 80 char, so checkpatch gives 80 char warning again.
- gpu/drm/omapdrm/omap_encoder.c
- gpu/drm/i915/intel_sdvo.c
V2: Rebase, Added r-b from Andrzej
V3: Addressed review comment from Ville:
- Do not send VICs in both AVI-IF and HDMI-IF
send only one of it.
V4: Rebase
V5: Added r-b from Neil.
Addressed review comments from Ville
- Do not block HDMI vendor IF, instead check for VIC while
handling AVI infoframes
V6: Rebase
V7: Rebase
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1499960000-9232-2-git-send-email-shashank.sharma@intel.com
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
The CRTC .disable() helper operation is deprecated for atomic drivers,
the new .atomic_disable() helper operation being preferred. Convert all
atomic drivers to .atomic_disable() to avoid cargo-cult use of
.disable() in new drivers.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> # for sun4i
Acked-by: Philipp Zabel <p.zabel@pengutronix.de> # for mediatek
Acked-by: Alexey Brodkin <abrodkin@synopsys.com> # for arcpgu
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com> # for atmel-hlcdc
Tested-by: Philippe Cornu <philippe.cornu@st.com> # for stm
Acked-by: Philippe Cornu <philippe.cornu@st.com> # for stm
Acked-by: Vincent Abriou <vincent.abriou@st.com> # for sti
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com> # for vmwgfx
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170630093646.7928-3-laurent.pinchart+renesas@ideasonboard.com
The old state is useful for drivers that need to perform operations at
enable time that depend on the transition between the old and new
states.
While at it, rename the operation to .atomic_enable() to be consistent
with .atomic_disable(), as the .enable() operation is used by atomic
helpers only.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> # for sun4i
Acked-by: Philipp Zabel <p.zabel@pengutronix.de> # for imx-drm and mediatek
Acked-by: Alexey Brodkin <abrodkin@synopsys.com> # for arcpgu
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com> # for atmel-hlcdc
Acked-by: Liviu Dudau <Liviu.Dudau@arm.com> # for hdlcd and mali-dp
Acked-by: Stefan Agner <stefan@agner.ch> # for fsl-dcu
Tested-by: Philippe Cornu <philippe.cornu@st.com> # for stm
Acked-by: Philippe Cornu <philippe.cornu@st.com> # for stm
Acked-by: Vincent Abriou <vincent.abriou@st.com> # for sti
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com> # for vmwgfx
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170630093646.7928-2-laurent.pinchart+renesas@ideasonboard.com
In function submit_create, if nr_cmds or nr_bos is assigned with
negative value, the allocated buffer may be small than intended.
Using this buffer will lead to buffer overflow issue.
Signed-off-by: Kasin Li <donglil@codeaurora.org>
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Buffer object specific resources like pages, domains, sg list
need not be protected with struct_mutex. They can be protected
with a buffer object level lock. This simplifies locking and
makes it easier to avoid potential recursive locking scenarios
for SVM involving mmap_sem and struct_mutex. This also removes
unnecessary serialization when creating buffer objects, and also
between buffer object creation and GPU command submission.
Signed-off-by: Sushmita Susheelendra <ssusheel@codeaurora.org>
[robclark: squash in handling new locking for shrinker]
Signed-off-by: Rob Clark <robdclark@gmail.com>
A 2 pixel wide pink strip was observed on the left end of some HDMI
monitors configured in a HDMI mode.
It turned out that we were missing out on configuring AVI infoframes, and
unlike APQ8064, the 8x96 HDMI H/W seems to be sensitive to that.
Add configuration of AVI infoframes. While at it, make sure that
hdmi_audio_update is only called when we've detected that the monitor
supports HDMI.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Without doing anything in unprepare, the HDMI driver isn't able to
switch modes successfully. Calling set_rate with a new rate results
in an un-locked PLL.
If we reset the PLL in unprepare, the PLL is able to lock with the
new rate.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Commit c0c0d9eeeb ("drm/msm: hdmi audio support") uses logical
OR operators to build up a value to be written in the
REG_HDMI_AUDIO_INFO0 and REG_HDMI_AUDIO_INFO1 registers when it
should have used bitwise operators.
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Fixes: c0c0d9eeeb ("drm/msm: hdmi audio support")
Signed-off-by: Rob Clark <robdclark@gmail.com>
Now that the msm_gem supports an arbitrary number of vma's, we no longer
need to assign an id (index) to each address space. So rip out the
associated code.
Signed-off-by: Rob Clark <robdclark@gmail.com>
It means we have to do a list traversal where we once had an index into
a table. But the list will normally have one or two entries.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Pull some of the logic out into msm_gem_new() (since we don't need to
care about the imported-bo case), and don't defer allocating pages. The
latter is generally a good idea, since if we are using VRAM carveout to
allocate contiguous buffers (ie. no IOMMU), the allocation is more
likely to fail. So failing at allocation time is a more sane option.
Plus this simplifies things in the next patch.
Signed-off-by: Rob Clark <robdclark@gmail.com>
No functional change, that will come later. But this will make it
easier to deal with dynamically created address spaces (ie. per-
process pagetables for gpu).
Signed-off-by: Rob Clark <robdclark@gmail.com>
Before we can shift to passing the address-space object to _get_iova(),
we need to fix a few places (dsi+fbdev) that were hard-coding the adress
space id. That gets somewhat easier if we just move these to the kms
base class.
Prep work for next patch.
Signed-off-by: Rob Clark <robdclark@gmail.com>
It serves no purpose, things should be sufficiently synchronized already
by atomic framework. And it is somewhat awkward to be holding a spinlock
when msm_gem_iova() is going to start needing to grab a mutex.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Most, but not all, paths where calling the with struct_mutex held. The
fast-path in msm_gem_get_iova() (plus some sub-code-paths that only run
the first time) was masking this issue.
So lets just always hold struct_mutex for hw_init(). And sprinkle some
WARN_ON()'s and might_lock() to avoid this sort of problem in the
future.
Signed-off-by: Rob Clark <robdclark@gmail.com>
memptrs->wptr seems to be unused. Remove it to avoid
confusing the upcoming preemption code.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The amount of information that we need to pass into msm_gpu_init()
is steadily increasing, so add a new struct to stabilize the function
call and make it easier to add new configuration down the line.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Modify the 'pad' member of struct drm_msm_gem_info to 'flags'. If the
user sets 'flags' to non-zero it means that they want a IOVA for the
GEM object instead of a mmap() offset. Return the iova in the 'offset'
member.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
[robclark: s/hint/flags in commit msg]
Signed-off-by: Rob Clark <robdclark@gmail.com>
There isn't any generic code that uses ->idle so remove it.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The ioctl array is sparsely populated but the compiler will make sure
that it is sufficiently sized for all the values that we have so we
can safely use ARRAY_SIZE() instead of having a constantly changing
#define in the uapi header.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The A5XX GPU powers on in "secure" mode. In secure mode the GPU can
only render to buffers that are marked as secure and inaccessible
to the kernel and user through a series of hardware protections. In
practice secure mode is used to draw things like a UI on a secure
video frame.
In order to switch out of secure mode the GPU executes a special
shader that clears out the GMEM and other sensitve registers and
then writes a register. Because the kernel can't be trusted the
shader binary is signed and verified and programmed by the
secure world. To do this we need to read the MDT header and the
segments from the firmware location and put them in memory and
present them for approval.
For targets without secure support there is an out: if the
secure world doesn't support secure then there are no hardware
protections and we can freely write the SECVID_TRUST register from
the CPU. We don't have 100% confidence that we can query the
secure capabilities at run time but we have enough calls that
need to go right to give us some confidence that we're at least doing
something useful.
Of course if we guess wrong you trigger a permissions violation
which usually ends up in a system crash but thats a problem
that shows up immediately.
[v2: use child device per Bjorn]
[v3: use generic MDT loader per Bjorn]
[v4: use managed dma functions and ifdefs for the MDT loader]
[v5: Add depends for QCOM_MDT_LOADER]
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
[robclark: fix Kconfig to use select instead of depends + #if IS_ENABLED()]
Signed-off-by: Rob Clark <robdclark@gmail.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJZPdbLAAoJEHm+PkMAQRiGx4wH/1nCjfnl6fE8oJ24/1gEAOUh
biFdqJkYZmlLYHVtYfLm4Ueg4adJdg0wx6qM/4RaAzmQVvLfDV34bc1qBf1+P95G
kVF+osWyXrZo5cTwkwapHW/KNu4VJwAx2D1wrlxKDVG5AOrULH1pYOYGOpApEkZU
4N+q5+M0ce0GJpqtUZX+UnI33ygjdDbBxXoFKsr24B7eA0ouGbAJ7dC88WcaETL+
2/7tT01SvDMo0jBSV0WIqlgXwZ5gp3yPGnklC3F4159Yze6VFrzHMKS/UpPF8o8E
W9EbuzwxsKyXUifX2GY348L1f+47glen/1sedbuKnFhP6E9aqUQQJXvEO7ueQl4=
=m2Gx
-----END PGP SIGNATURE-----
BackMerge tag 'v4.12-rc5' into drm-next
Linux 4.12-rc5 for nouveau fixes
The overrun check for the size of submitted commands is off by one.
It should allow the offset plus the size to be equal to the
size of the memory object when the command stream is very tightly
constructed.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Amongst its other duties, msm_gem_new_impl adds the newly created
GEM object to the shared inactive list which may also be actively
modifiying the list during submission. All the paths to modify
the list are protected by the mutex except for the one through
msm_gem_import which can end up causing list corruption.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
[add extra WARN_ON(!mutex_is_locked(&dev->struct_mutex))]
Signed-off-by: Rob Clark <robdclark@gmail.com>
Use the dma_fence_match_context helper to check if all backing fences
are from our own context, in which case we don't have to wait.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Gustavo Padovan <gustavo.padovan@collabora.com>
[rebased on code-motion]
Signed-off-by: Rob Clark <robdclark@gmail.com>
struct irq_domain_ops is not modified, so it can be made const.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Rob Clark <robdclark@gmail.com>
If we follow the typical pattern of the base class being the first
member, we can use the default dma_fence_free function.
Signed-off-by: Eric Anholt <eric@anholt.net>
Cc: Rob Clark <robdclark@gmail.com>
Cc: linux-arm-msm@vger.kernel.org
Cc: freedreno@lists.freedesktop.org
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Without this, polling on the dma-buf (and presumably other devices
synchronizing against our rendering) would return immediately, even
while the BO was busy.
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Cc: Rob Clark <robdclark@gmail.com>
Cc: linux-arm-msm@vger.kernel.org
Cc: freedreno@lists.freedesktop.org
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Otherwise if someone was using old bindings with "core_clk" instead of
"core" as the clock name, we'd never find it and gpu would be stuck at
27MHz (or whatever it's slowest rate is).
Fixes: 98db803 ("msm/drm: gpu: Dynamically locate the clocks from the device tree")
Signed-off-by: Rob Clark <robdclark@gmail.com>
Otherwise, if nothing else enabled selects it, dev_pm_opp_of_add_table()
will return -ENOTSUPP.
Fixes: e2af8b6 ("drm/msm: gpu: Use OPP tables if we can")
Signed-off-by: Rob Clark <robdclark@gmail.com>
Add DRM_MODE_ROTATE_ and DRM_MODE_REFLECT_ defines to the UAPI
as a convenience.
Ideally the DRM_ROTATE_ and DRM_REFLECT_ property ids are looked up
through the atomic API, but realizing that userspace is likely to take
shortcuts and assume that the enum values are what is sent over the
wire.
As a result these defines are provided purely as a convenience to
userspace applications.
Changes since v3:
- Switched away from past tense in comments
- Add define name change to previously mis-spelled DRM_REFLECT_X comment
- Improved the comment for the DRM_MODE_REFLECT_<axis> comment
Changes since v2:
- Changed define prefix from DRM_MODE_PROP_ to DRM_MODE_
- Fix compilation errors
- Changed comment formatting
- Deduplicated comment lines
- Clarified DRM_MODE_PROP_REFLECT_ comment
Changes since v1:
- Moved defines from drm.h to drm_mode.h
- Changed define prefix from DRM_ to DRM_MODE_PROP_
- Updated uses of the defines to the new prefix
- Removed include from drm_rect.c
- Stopped using the BIT() macro
Signed-off-by: Robert Foss <robert.foss@collabora.com>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
Acked-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170519205017.23307-2-robert.foss@collabora.com
Now that drm_[cm]alloc* helpers are simple one line wrappers around
kvmalloc_array and drm_free_large is just kvfree alias we can drop
them and replace by their native forms.
This shouldn't introduce any functional change.
Changes since v1
- fix typo in drivers/gpu//drm/etnaviv/etnaviv_gem.c - noticed by 0day
build robot
Suggested-by: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Michal Hocko <mhocko@suse.com>drm: drop drm_[cm]alloc* helpers
[danvet: Fixup vgem which grew another user very recently.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Christian König <christian.koenig@amd.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170517122312.GK18247@dhcp22.suse.cz
Include <drm/*.h> instead of relative path from include/drm, then
remove the -Iinclude/drm compiler flag.
While we are here, sort the touched parts with public headers first.
mdp4_kms.h must declare struct device_node to be self-contained.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1493009447-31524-11-git-send-email-yamada.masahiro@socionext.com
If we restrict this helper to only kms drivers (which is the case) we
can look up the correct mode easily ourselves. But it's a bit tricky:
- All legacy drivers look at crtc->hwmode. But that is updated already
at the beginning of the modeset helper, which means when we disable
a pipe. Hence the final timestamps might be a bit off. But since
this is an existing bug I'm not going to change it, but just try to
be bug-for-bug compatible with the current code. This only applies
to radeon&amdgpu.
- i915 tries to get it perfect by updating crtc->hwmode when the pipe
is off (i.e. vblank->enabled = false).
- All other atomic drivers look at crtc->state->adjusted_mode. Those
that look at state->requested_mode simply don't adjust their mode,
so it's the same. That has two problems: Accessing crtc->state from
interrupt handling code is unsafe, and it's updated before we shut
down the pipe. For nonblocking modesets it's even worse.
For atomic drivers try to implement what i915 does. To do that we add
a new hwmode field to the vblank structure, and update it from
drm_calc_timestamping_constants(). For atomic drivers that's called
from the right spot by the helper library already, so all fine. But
for safety let's enforce that.
For legacy driver this function is only called at the end (oh the
fun), which is broken, so again let's not bother and just stay
bug-for-bug compatible.
The benefit is that we can use drm_calc_vbltimestamp_from_scanoutpos
directly to implement ->get_vblank_timestamp in every driver, deleting
a lot of code.
v2: Completely new approach, trying to mimick the i915 solution.
v3: Fixup kerneldoc.
v4: Drop the WARN_ON to check that the vblank is off, atomic helpers
currently unconditionally call this. Recomputing the same stuff should
be harmless.
v5: Fix typos and move misplaced hunks to the right patches (Neil).
v6: Undo hunk movement (kbuild).
Cc: Mario Kleiner <mario.kleiner@tuebingen.mpg.de>
Cc: Eric Anholt <eric@anholt.net>
Cc: Rob Clark <robdclark@gmail.com>
Cc: linux-arm-msm@vger.kernel.org
Cc: freedreno@lists.freedesktop.org
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Christian König <christian.koenig@amd.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170509140329.24114-4-daniel.vetter@ffwll.ch
It's overkill to have a flag parameter which is essentially used just
as a boolean. This takes care of core + adjusting drivers.
Adjusting the scanout position callback is a bit harder, since radeon
also supplies it's own driver-private flags in there.
v2: Fixup misplaced hunks (Neil).
v3: kbuild says v1 was better ...
Cc: Mario Kleiner <mario.kleiner@tuebingen.mpg.de>
Cc: Eric Anholt <eric@anholt.net>
Cc: Rob Clark <robdclark@gmail.com>
Cc: linux-arm-msm@vger.kernel.org
Cc: freedreno@lists.freedesktop.org
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Christian König <christian.koenig@amd.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170509140329.24114-2-daniel.vetter@ffwll.ch
There's really no reason for anything more:
- Calling this while the crtc vblank stuff isn't set up is a driver
bug. Those places alrready DRM_ERROR.
- Calling this when the crtc is off is either a driver bug (calling
drm_crtc_handle_vblank at the wrong time) or a core bug (for
anything else). Again, we DRM_ERROR.
- EINVAL is checked at higher levels already, and if we'd use struct
drm_crtc * instead of (dev, pipe) it would be real obvious that
those are again core bugs.
The only valid failure mode is crap hardware that couldn't sample a
useful timestamp, to ask the core to just grab a not-so-accurate
timestamp. Bool is perfectly fine for that.
v2: Also fix up the one caller, I lost that in the shuffling (Jani).
v3: Fixup commit message (Neil).
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Mario Kleiner <mario.kleiner@tuebingen.mpg.de>
Cc: Eric Anholt <eric@anholt.net>
Cc: Rob Clark <robdclark@gmail.com>
Cc: linux-arm-msm@vger.kernel.org
Cc: freedreno@lists.freedesktop.org
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Christian König <christian.koenig@amd.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170509140329.24114-1-daniel.vetter@ffwll.ch
Noteworthy changes this time:
1) 4k support for newer chips (ganging up hwpipes and mixers)
2) using OPP bindings for gpu
3) more prep work towards per-process pagetables
* 'msm-next' of git://people.freedesktop.org/~robclark/linux: (47 commits)
msm/drm: gpu: Dynamically locate the clocks from the device tree
drm/msm: gpu: Use OPP tables if we can
drm/msm: Hard code the GPU "slow frequency"
drm/msm: Add MSM_PARAM_GMEM_BASE
drm/msm: Reference count address spaces
drm/msm: Make sure to detach the MMU during GPU cleanup
drm/msm/mdp5: Enable 3D mux in mdp5_ctl
drm/msm/mdp5: Reset CTL blend registers before configuring them
drm/msm/mdp5: Assign 'right' mixer to CRTC state
drm/msm/mdp5: Stage border out on base stage if CRTC has 2 LMs
drm/msm/mdp5: Stage right side hwpipes on Right-side Layer Mixer
drm/msm/mdp5: Prepare Layer Mixers for source split
drm/msm/mdp5: Configure 'right' hwpipe
drm/msm/mdp5: Assign a 'right hwpipe' to plane state
drm/msm/mdp5: Create mdp5_hwpipe_mode_set
drm/msm/mdp5: Add optional 'right' Layer Mixer in CRTC state
drm/msm/mdp5: Add a CAP for Source Split
drm/msm/mdp5: Remove mixer/intf pointers from mdp5_ctl
drm/msm/mdp5: Start using parameters from CRTC state
drm/msm/mdp5: Add more stuff to CRTC state
...
Last drm-misc-next pull req for 4.12
Core changes:
- fb_helper checkpatch cleanup and simplified _add_one_connector() (Thierry)
- drm_ioctl and drm_sysfs improved/gained documentation (Daniel)
- [ABI] Repurpose reserved field in drm_event_vblank for crtc_id (Ander)
- Plumb acquire ctx through legacy paths to avoid lock_all and legacy_backoff
(Daniel)
- Add connector_atomic_check to check conn constraints on modeset (Maarten)
- Add drm_of_find_panel_or_bridge to remove boilerplate in drivers (Rob)
Driver changes:
- meson moved to drm-misc (Neil)
- Added support for Amlogic GX SoCs in dw-hdmi (Neil)
- Rockchip unbind actually cleans up the things bind initializes (Jeffy)
- A couple misc fixes in virtio, dw-hdmi
NOTE: this also includes a backmerge of drm-next as well rc5 (we needed vmwgfx
as well as the new synopsys media formats)
* tag 'drm-misc-next-2017-04-07' of git://anongit.freedesktop.org/git/drm-misc: (77 commits)
Revert "drm: Don't allow interruptions when opening debugfs/crc"
drm: Only take cursor locks when the cursor plane exists
drm/vmwgfx: Fix fbdev emulation using legacy functions
drm/rockchip: Shutdown all crtcs when unbinding drm
drm/rockchip: Reorder drm bind/unbind sequence
drm/rockchip: analogix_dp: Disable clock when unbinding
drm/rockchip: vop: Unprepare clocks when unbinding
drm/rockchip: vop: Enable pm domain before vop_initial
drm/rockchip: cdn-dp: Don't unregister audio dev when unbinding
drm/rockchip: cdn-dp: Don't try to release firmware when not loaded
drm: bridge: analogix: Destroy connector & encoder when unbinding
drm: bridge: analogix: Disable clock when unbinding
drm: bridge: analogix: Unregister dp aux when unbinding
drm: bridge: analogix: Detach panel when unbinding analogix dp
drm: Don't allow interruptions when opening debugfs/crc
drm/virtio: don't leak bo on drm_gem_object_init failure
drm: bridge: dw-hdmi: fix input format/encoding from plat_data
drm: omap: use common OF graph helpers
drm: convert drivers to use drm_of_find_panel_or_bridge
drm: convert drivers to use of_graph_get_remote_node
...
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJY6mY1AAoJEHm+PkMAQRiGB14IAImsH28JPjxJVDasMIRPBxVc
euPPlZgoBieu7sNt+kEsEqdkXuu0MLk6gln0IGxWLeoB2S+u3Tz5LMa2YArVqV9Z
tWzOnI9auE73P2Pz/tUMOdyMs5tO0PolQxX3uljbULBozOHjHRh13fsXchX2yQvl
mFeFCDqpPV0KhWRH/ciA8uIHdvYPhMpkKgRtmR8jXL0yzqLp6+2J+Bs8nHG4NNng
HMVxZPC8jOE/TgWq6k/GmXgxh3H/AideFdHFbLKYnIFJW41ZGOI8a262zq3NmjPd
lywpVU7O7RMhSITY5PnuR3LpNV8ftw1hz2y6t35unyFK1P02adOSj5GJ3hGdhaQ=
=Xz5O
-----END PGP SIGNATURE-----
Backmerge tag 'v4.11-rc6' into drm-next
Linux 4.11-rc6
drm-misc needs 4.11-rc5, may as well fix conflicts with rc6.
Instead of using a fixed list of clock names use the clock-names
list in the device tree to discover and get the list of clocks
that we need.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
If a OPP table is defined for the GPU device in the device tree use
that in lieu of the downstream style GPU frequency table. If we do
use the downstream table convert it to a OPP table so that we can
take advantage of the OPP lookup facilities later.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Some A3XX and A4XX GPU targets required that the GPU clock be
programmed to a non zero value when it was disabled so
27Mhz was chosen as the "invalid" frequency.
Even though newer targets do not have the same clock restrictions
we still write 27Mhz on clock disable and expect the clock subsystem
to round down to zero.
For unknown reasons even though the slow clock speed is always
27Mhz and it isn't actually a functional level the legacy device tree
frequency tables always defined it and then did gymnastics to work
around it.
Instead of playing the same silly games just hard code the "slow" clock
speed in the code as 27MHz and save ourselves a bit of infrastructure.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
User space needs to know where the GMEM whole starts so that they
can set up the addressing correctly.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
There are reasons for a memory object to outlive the file descriptor
that created it and so the address space that a buffer object is
attached to must also outlive the file descriptor. Reference count
the address space so that it can remain viable until all the objects
have released their addresses.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
We should be detaching the MMU before destroying the address
space. To do this cleanly, the detach has to happen in
adreno_gpu_cleanup() because it needs access to structs
in adreno_gpu.c. Plus it is better symmetry to have
the attach and detach at the same code level.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
3D mux is a small block placed after the DSPPs in MDP5. It can merge
2 LM/DSPP outputs and feed it to a single interface.
Enable 3D Mux if our mdp5_pipeline has 2 active LMs. This check
will need to be made more specific later when we add Dual DSI
support with source split enabled. In that use case, each LM feeds to a
separae INTF, so the 3D mux isn't needed.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Assigning LMs dynamically to CRTCs results in REG_MDP5_CTL_LAYER_REGs
and REG_MDP5_CTL_LAYER_EXT_REGs maintaining old values for a LM that
isn't used by our CTL instance anymore.
Clear the ctl's CTL_LAYER_REG and CTL_LAYER_EXT_REGs for all LM
instances. The ones that need to be configured are configured later
in this func.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Dynamically assign a right mixer to mdp5_crtc_state in the CRTC's
atomic_check path. Assigning the right mixer has some constraints,
i.e, only a few LMs can be paired together. Update mdp5_mixer_assign
to handle these constraints.
Firstly, we need to identify whether we need a right mixer or not.
At the moment, there are 2 scenarios where a right mixer might be
needed:
- If any of the planes connected to this CRTC is too wide (i.e, is
comprised of 2 hwpipes).
- If the CRTC's mode itself is too wide (i.e, a 4K mode on HDMI).
We implement both these checks in the mdp5_crtc_atomic_check(), and
pass 'need_right_mixer' to mdp5_setup_pipeline.
If a CRTC is already assigned a single mixer, and a new atomic commit
brings in a drm_plane that needs 2 hwpipes, we can successfully commit
this mode without requiring a full modeset, provided that we still use
the previously assigned mixer as the left mixer. If such an assignment
isn't possible, we'd need to do a full modeset. This scenario has been
ignored for now.
The mixer assignment code is a bit messy, considering we have at most
4 LM instances in hardware. This can probably be re-visited later with
simplified logic.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
If a CRTC comprises of 2 LMs, it is mandatory to enable border out
and assign it to the base stage.
We had to enable border out also when the base plane wasn't fullscreen.
Club these checks and put them in a separate function called
get_start_stage() that returns the starting stage for assigning planes.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Now that our mdp5_planes can consist of 2 hwpipes, update the
blend_setup() code to stage the right hwpipe to the left and
right LMs
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
In order to enable Source Split in HW, we need to add/modify
a few LM register configurations:
- Configure the LM width to be half the mode width, so that
each LM manages one half of the scanout.
- Tell the 'right' LM that it is configured to be the 'right'
LM in source split mode.
- Since we now have 2 places where REG_MDP5_LM_BLEND_COLOR_OUT is
configured, do a read-update-store for the register instead of
directly writing a value to it.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Now that we have a right hwpipe in mdp5_plane_state, configure it
mdp5_plane_mode_set(). The only parameters that vary between the
left and right hwpipes are the src_w, src_img_w, src_x and crtc_x
as we just even chop the fb into left and right halves.
Add a mdp5_plane_right_pipe() which will be used by the crtc code
to set up LM stages.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
If the drm_plane has a source width that's greater than the max width
supported by a SSPP (2560 pixels on 8x96), then we assign a 'r_hwpipe'
to it in mdp5_plane_atomic_check().
TODO: There are a few scenarios where the hwpipe assignments aren't
recommended by HW. For example, an assignment which results in a
drm_plane to of two different types of hwpipes (say RGB0 on left
and DMA1 on right) is not recommended.
Also, hwpipes have a priority mapping, where the higher priority pipe
needs to be staged on left LM, and the lower priority needs to be
staged on the right LM. For example, the priority order for VIG pipes
in decreasing order of priority is VIG0, VIG1, VIG2, and VIG3. So, VIG0
on left and VIG1 on right is a correct configuration, but VIG1 on left
and VIG0 on right isn't. These scenarios are ignored for now for the
sake of simplicity.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Refactor mdp5_plane_mode_set to call mdp5_hwpipe_mode_set. The latter
func takes in only the hwpipe and the parameters that need to be
programmed into the hwpipe registers. All the code that calculates these
parameters is left as is in mdp5_plane_mode_set.
In the future, when we let drm_plane be comprised of 2 hwpipes, this func
allow us to configure each pipe without adding redundant code.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Add another mdp5_hw_mixer pointer (r_mixer) in mdp5_crtc_state.
This mixer will be used to generate the right half of the scanout.
With Source Split, a SSPP can now be connected to 2 Layer Mixers, but
has to be at the same blend level (stage #) on both Layer Mixers.
A drm_plane that has a lesser width than the max width supported, will
comprise of a single SSPP/hwpipe, staged on both the Layer Mixers at
the same blend level. A plane that is greater than max width will comprise
of 2 SSPPs, with the 'left' SSPP staged on the left LM, and the 'right'
SSPP staged on the right LM at the same blend level.
For now, the drm_plane consists of only one SSPP, therefore, it
needs to be staged on both the LMs in blend_setup() and mdp5_ctl_blend().
We'll extend this logic to support 2 hwpipes per plane later.
The crtc cursor ops (using the LM cursors, not SSPP cursors) simply
return an error if they're called when the right mixer is assigned to
the CRTC state. With source split is enabled, we're expected to only
SSPP cursors.
This commit adds code that configures the right mixer, but the r_mixer
itself isn't assigned at the moment.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Some of the newer MDP5 versions support Source Split of SSPPs. It is a
feature that allows us to route the output of a hwpipe to 2 Layer
Mixers. This is required to achieve the following use cases:
- Dual DSI: For high res DSI panels (such as 2560x1600 etc), a single
DSI interface doesn't have the bandwidth to drive the required pixel
clock. We use 2 DSI interfaces to drive the left and right halves
of the panel (i.e, 1280x1600 each). The MDP5 pipeline here would look
like:
LM0 -- DSPP0 -- INTF1 -- DSI1
/
hwpipe--
\
LM1 -- DSPP1 -- INTF2 -- DSI2
A single hwpipe is used to scan out the left and right halves to DSI1
and DSI2 respectively. In order to do this, we need to configure the
2 Layer Mixers in Source Split mode.
- HDMI 4K: In order to support resolutions with width higher than the
max width supported by a hwpipe, we club 2 hwpipes together:
hwpipe1 --- LM0 -- DSPP0
- - \
- -- 3D Mux -- INTF0 -- HDMI
- - /
hwpipe2 --- LM1 -- DSPP1
hwpipe1 is staged on the 'left' Layer Mixer, and hwpipe2 is staged on
the 'right' Layer Mixer. An additional block called the '3D Mux' is
used to merge the output of the 2 DSPPs to a single interface.
In this use case, it is possible that a 4K surface is downscaled and
placed completely within one of the halves. In order to support such
scenarios (and keep the programming simple), Layer Mixers with Source
Split can be assigned 2 hw pipes per stage. While scanning out, the HW
takes care of fetching the pixels fom the correct pipe.
Add a MDP cap to tell whether the HW supports source split or not.
Add a MDP LM cap that tells whether a LM instance can operate in
source split mode (and generate the 'left' part of the display
output).
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
These are a part of CRTC state, it doesn't feel nice to leave them
hanging in mdp5_ctl struct. Pass mdp5_pipeline pointer instead
wherever it is needed.
We still have some params in mdp5_ctl like start_mask etc which
are derivative of atomic state, and should be rolled back if
a commit fails, but it doesn't seem to cause much trouble.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
In the last few commits, we've been adding params to mdp5_crtc_state, and
assigning them in the atomic_check() funcs. Now it's time to actually
start using them.
Remove the duplicated params from the mdp5_crtc struct, and start using
them in the mdp5_crtc code. The majority of the references to these params
is in code that executes after the atomic swap has occurred, so it's okay
to use crtc->state in them. There are a couple of legacy LM cursor ops that
may not use the updated state, but (I think) it's okay to live with that.
Now that we dynamically allocate a mixer to the CRTC, we can also remove
the static assignment to it in mdp5_crtc_init, and also drop the code that
skipped init-ing WB bound mixers (those will now be rejected by
mdp5_mixer_assign()).
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Things like vblank/err irq masks, mode of operation (command mode or not)
are derivative of the interface and mixer state. Therefore, they need to
be a part of the CRTC state too.
Add them to mdp5_crtc_state, and assign them in the CRTC's atomic_check()
func, so that it can be rolled back to a clean state.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The INTF and CTL used in a display pipeline are going to be maintained as
a part of the CRTC state (i.e, in mdp5_crtc_state).
These entities, however, are currently statically assigned to drm_encoders
(i.e. mdp5_encoder). Since these aren't directly visible to the CRTC, we
assign them to the CRTC state in the encoder's atomic_check() op.
With this approach, we assign portions of CRTC state in two different
places: the layer mixer in CRTC's atomic_check(), and the INTF and CTL
pieces in the encoder's atomic_check() op.
We'd have more options here if the drm core maintained encoder state too,
but the current approach of clubbing everything in CRTC's state works just
fine.
Unlike hwpipes and mixers, we don't need to keep a track of INTF/CTL
assignments in the global atomic state. This is because they're currently
not sharable resources. For example, INTF0 and CTL0 will always be assigned
to one drm_encoder. This can change later when we implement writeback and
want a CRTC to use a CTL for a while, and then release it for others to use
it. Or, when a drm_encoder can switch between using a single INTF vs
2 INTFs.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Add the stuff needed to allow dynamically assigning a mixer to a CRTC.
Since mixers are a resource that can be shared across multiple CRTCs, we
need to maintain a 'hwmixer_to_crtc' map in the global atomic state,
acquire the mdp5_kms.state_lock modeset lock and so on.
The mixer is assigned in the CRTC's atomic_check() func, a failure will
result in the new state being cleanly rolled back.
The mixer assignment itself is straightforward, and almost identical to
what we do for hwpipes. We don't need to grab the old hwmixer_to_crtc
state like we do in hwpipes since we don't need to compare anything
with the old state at the moment.
The only LM capability we care about at the moment is whether the mixer
instance can be used to display stuff (i.e, connect to an INTF
downstream).
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Subclass drm_crtc_state so that we can maintain additional state for
our CRTCs.
Add mdp5_pipeline and mdp5_ctl pointers in the subclassed state.
mdp5_pipeline is a grouping of the HW entities that forms the downstream
pipeline for a particular CRTC. It currently contains pointers to
mdp5_interface and mdp5_hw_mixer tied to this CRTC. Later, we will
have 2 hwmixers in this struct. (We could also have 2 intfs if we want
to support dual DSI with Source Split enabled. Implementing that feature
isn't planned at the moment).
The mdp5_pipeline state isn't used at the moment. For now, we just
introduce mdp5_crtc_state and the crtc funcs needed to manage the
subclassed state.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The mdp5_ctl has an 'op_mode' struct which contains info on
the downstream pipeline.
Grouping these params together in a struct doesn't serve much
purpose in the code. Maybe there was a plan to expand this
further that never happened.
Remove the op_mode struct, and place its members directly in
mdp5_ctl. This will help avoid confusion later when I introduce
my own verion of a mdp5 pipeline :)
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
mdp5_interface struct contains data corresponding to a INTF
instance in MDP5 hardware. This sturct is memcpy'd to the
mdp5_encoder struct, and then later to the mdp5_ctl struct.
Instead of copying around interface data, create mdp5_interface
instances in mdp5_init, like how it's done currently done for
pipes and layer mixers. Pass around the interface pointers to
mdp5_encoder and mdp5_ctl. This simplifies the code, and allows
us to decouple encoders from INTFs in the future if needed.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
PingPong ID for a Layer Mixer is already contained in
mdp5_hw_mixer.
This avoids the need to retrieve PP ID using macros
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Use the mdp5_hw_mixer struct in the mdp5_crtc and mdp5_ctl instead of
using the LM index.
Like before, the Layer Mixers are assigned statically to the CRTCs.
The hwmixer(s) will later be dynamically assigned to CRTCs.
For now, ignore the hwmixers that can only do WB.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Create a struct to represent MDP5 Layer Mixer instances. This will
eventually allow us to detach CRTCs from the Layer Mixers, and
generally clean things up a bit.
This is very similar to how hwpipes were previously abstracted away
from drm planes.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The number of Layer Mixers and the downstream blocks (DSPPs and PPs)
connected to each LM can vary with different MDP5 revisions. These
parameters are also static.
Keep the per instance LM data in mdp5_cfg. This will avoid the need
to have macros which identify PP id or DSPP id the LM is connected
to. We don't configure DSPPs at the moment, but keeping the DSPP
instance # here might come handy later.
Also add a 'caps' field that identifies features supported by a
LM instance. Introduce the caps MDP_LM_CAP_DISPLAY and MDP_LM_CAP_WB
that identify whether a LM instance can be used for display or
writeback.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
We'd previously moved the pipe_lock spinlock to the hwpipe struct. Bring
it back to mdp5_plane. We will need this because an mdp5_plane in the
future could comprise of 2 hw pipes. It makes more sense to have a single
lock to protect the registers for the hw pipes used by a plane, rather
than trying to take individual locks per hwpipe when committing a
configuration.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
4 macros already defined in hdmi.h,
which is not required to redefine in hdmi_audio.c
Signed-off-by: Vinay Simha BN <simhavcs@gmail.com>
Signed-off-by: Rob Clark <robdclark@gmail.com>
'SSPP_MAX + 1' is the max number of hwpipes that can be present on a
MDP5 platform. Recently, 2 new cursor hwpipes were added, which
caused overflows in arrays that used SSPP_MAX to represent the number
of elements. Update the SSPP_MAX value to incorporate the extra
hwpipes.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
A recent commit introduces a bug in dsi_mgr_phy_enable. In the non
dual DSI mode, we reset the mdsi (master DSI) PHY. This isn't right
since master and slave DSI exist only in dual DSI mode. For the normal
mode of operation, we should simply reset the PHY of the DSI device
(i.e. msm_dsi) corresponding to the current bridge.
Usage of the wrong DSI pointer also resulted in a static checker
warning. That too is resolved with this fix.
Fixes: b62aa70a98 (drm/msm/dsi: Move PHY operations out of host)
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Zero sized buffer objects tend to make various bits of the GEM
infrastructure complain:
WARNING: CPU: 1 PID: 2323 at drivers/gpu/drm/drm_mm.c:389 drm_mm_insert_node_generic+0x258/0x2f0
Modules linked in:
CPU: 1 PID: 2323 Comm: drm-api-test Tainted: G W 4.9.0-rc4-00906-g693af44 #213
Hardware name: Qualcomm Technologies, Inc. DB820c (DT)
task: ffff8000d7353400 task.stack: ffff8000d7720000
PC is at drm_mm_insert_node_generic+0x258/0x2f0
LR is at drm_vma_offset_add+0x4c/0x70
Zero sized buffers serve no appreciable value to the user so disallow
them at create time.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Output the upper 32 bits of a 64 bit iova in the RD_CMDSTREAM_ADDR
section while maintaining backwards compatibility for tools that
only understand 32 bit iovas.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The interrupt status was being cleared before processing the handlers.
a5xx_rbbm_err_irq() was checking the interrupt status again, which would
likely turn out bad because the interrupt status would be 0 (or at least
different). Pass the original status to the function instead.
Also, skip clearing RBBM_AHB_ERROR from the interrupt status. The interrupt
will keep firing until the error source is cleared. Skip the clear to
avoid a storm until the error is cleared in a5xx_rbbm_err_irq().
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
priv->num_aspaces is increased and then checked to see if it still fits
in the priv->aspace array. If it doesn't, we warn and exit but
priv->num_aspaces remains incremented.
Don't incremement the count until we know that it fits in the array.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Instead of checking for a5xx_gpu->gpmu_iova during destroy we
accidently check a5xx_gpu->gpmu_bo.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The core takes care of handling the send_event vs. close() issues, we
can remove that driver code.
Cc: Rob Clark <robdclark@gmail.com>
Cc: linux-arm-msm@vger.kernel.org
Cc: freedreno@lists.freedesktop.org
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Rob Clark <robdclark@gmail.com>
I didn't spot anything that would require ordering here (well not
anywhere else either), and I'm trying to unify at least modern drivers
on one close hook.
Cc: Rob Clark <robdclark@gmail.com>
Cc: linux-arm-msm@vger.kernel.org
Cc: freedreno@lists.freedesktop.org
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The newly added a5xx support fails to build when debugfs is diabled:
drivers/gpu/drm/msm/adreno/a5xx_gpu.c:849:4: error: 'struct msm_gpu_funcs' has no member named 'show'
drivers/gpu/drm/msm/adreno/a5xx_gpu.c:849:11: error: 'a5xx_show' undeclared here (not in a function); did you mean 'a5xx_irq'?
This adds a missing #ifdef.
Fixes: b5f103ab98 ("drm/msm: gpu: Add A5XX target support")
Cc: stable@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Probably a symptom of needing finer grained locking, but if we wait on
the incoming fence-fd (which could come from a different context) while
holding struct_mutex, that blocks retire_worker so gpu fences cannot get
signalled.
This causes a problem if userspace manages to get more than a frame
ahead, leaving the atomic-commit worker blocked waiting on fences that
cannot be signaled because submit is blocked waiting for a fence
signalled from vblank (after the atomic commit which is blocked).
If we start having multiple fence ctxs for the gpu, submit_fence_sync()
would probably need to move outside of struct_mutex as well.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Significantly simplifies things. Also iommu_unmap() can unmap an entire
iova range.
(If backporting to downstream kernel you might need to revert this. Or
at least double check older iommu implementation.)
Signed-off-by: Rob Clark <robdclark@gmail.com>
Each of the per-generation callbacks was doing this. Lets just simplify
and move it into toplevel show() fxn.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Convert drivers to use the new of_graph_get_remote_node() helper
instead of parsing the endpoint node and then getting the remote device
node. Now drivers can just specify the device node and which
port/endpoint and get back the connected remote device node. The details
of the graph binding are nicely abstracted into the core OF graph code.
This changes some error messages to debug messages (in the graph core).
Graph connections are often "no connects" depending on the particular
board, so we want to avoid spurious messages. Plus the kernel is not a
DT validator.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Liviu Dudau <liviu.dudau@arm.com>
Tested-by: Eric Anholt <eric@anholt.net>
Tested-by: Jyri Sarha <jsarha@ti.com>
Tested by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
We should be detaching the MMU before destroying the address
space. To do this cleanly, the detach has to happen in
adreno_gpu_cleanup() because it needs access to structs
in adreno_gpu.c. Plus it is better symmetry to have
the attach and detach at the same code level.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
4 macros already defined in hdmi.h,
which is not required to redefine in hdmi_audio.c
Signed-off-by: Vinay Simha BN <simhavcs@gmail.com>
Signed-off-by: Rob Clark <robdclark@gmail.com>
'SSPP_MAX + 1' is the max number of hwpipes that can be present on a
MDP5 platform. Recently, 2 new cursor hwpipes were added, which
caused overflows in arrays that used SSPP_MAX to represent the number
of elements. Update the SSPP_MAX value to incorporate the extra
hwpipes.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
A recent commit introduces a bug in dsi_mgr_phy_enable. In the non
dual DSI mode, we reset the mdsi (master DSI) PHY. This isn't right
since master and slave DSI exist only in dual DSI mode. For the normal
mode of operation, we should simply reset the PHY of the DSI device
(i.e. msm_dsi) corresponding to the current bridge.
Usage of the wrong DSI pointer also resulted in a static checker
warning. That too is resolved with this fix.
Fixes: b62aa70a98 (drm/msm/dsi: Move PHY operations out of host)
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Zero sized buffer objects tend to make various bits of the GEM
infrastructure complain:
WARNING: CPU: 1 PID: 2323 at drivers/gpu/drm/drm_mm.c:389 drm_mm_insert_node_generic+0x258/0x2f0
Modules linked in:
CPU: 1 PID: 2323 Comm: drm-api-test Tainted: G W 4.9.0-rc4-00906-g693af44 #213
Hardware name: Qualcomm Technologies, Inc. DB820c (DT)
task: ffff8000d7353400 task.stack: ffff8000d7720000
PC is at drm_mm_insert_node_generic+0x258/0x2f0
LR is at drm_vma_offset_add+0x4c/0x70
Zero sized buffers serve no appreciable value to the user so disallow
them at create time.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Instead of checking for a5xx_gpu->gpmu_iova during destroy we
accidently check a5xx_gpu->gpmu_bo.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The newly added a5xx support fails to build when debugfs is diabled:
drivers/gpu/drm/msm/adreno/a5xx_gpu.c:849:4: error: 'struct msm_gpu_funcs' has no member named 'show'
drivers/gpu/drm/msm/adreno/a5xx_gpu.c:849:11: error: 'a5xx_show' undeclared here (not in a function); did you mean 'a5xx_irq'?
This adds a missing #ifdef.
Fixes: b5f103ab98 ("drm/msm: gpu: Add A5XX target support")
Cc: stable@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Just rolling it out, no code change here.
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Eric Anholt <eric@anholt.net>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170322215058.8671-3-daniel.vetter@ffwll.ch
We now call those two functions even when they are not defined
or declared anywhere because DEBUG_FS is disabled:
drivers/gpu/drm/msm/msm_drv.c: In function 'msm_drm_uninit':
drivers/gpu/drm/msm/msm_drv.c:244:2: error: implicit declaration of function 'msm_perf_debugfs_cleanup';did you mean 'msm_framebuffer_cleanup'? [-Werror=implicit-function-declaration]
drivers/gpu/drm/msm/msm_drv.c:245:2: error: implicit declaration of function 'msm_rd_debugfs_cleanup';did you mean 'msm_framebuffer_cleanup'? [-Werror=implicit-function-declaration]
This adds empty stub implementations for that case.
Fixes: 85eac4700e ("drm/msm: Remove msm_debugfs_cleanup()")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170320093936.1255573-1-arnd@arndb.de
-----BEGIN PGP SIGNATURE-----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=BSWh
-----END PGP SIGNATURE-----
Merge tag 'doc-4.11-images' of git://git.lwn.net/linux into drm-misc-next
Pointer for Markus's image conversion work.
We need this so we can merge all the pretty drm graphs for 4.12.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Merge Laurent's drm_platform removal code. Only conflict is with the
drm_pci.h extraction, which allows me to fix up the misplayed
drm_platform_init fumble that 0day and Stephen Rothwell reported.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Move the contents of msm_debugfs_cleanup() to msm_drm_uninit() to free
up the drm_driver->debugfs_cleanup callback. Also remove the
mdp_kms_funcs->debugfs_cleanup callback which has no users.
Cc: robdclark@gmail.com
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Acked-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170307204924.1002-2-noralf@tronnes.org
drm_debugfs_cleanup() now removes all minor->debugfs_list entries
automatically, so it's not necessary to call
drm_debugfs_remove_files(). Additionally it uses
debugfs_remove_recursive() to clean up the debugfs files, so no need
to do that.
Cc: robdclark@gmail.com
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170126225621.12314-10-noralf@tronnes.org
Use a more common logging style.
Miscellanea:
o Coalesce formats and realign arguments
o Neaten a few macros now using pr_<level>
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Rob Clark <robdclark@gmail.com>
Acked-by: Sinclair Yeh <syeh@vmware.com>
Acked-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/76355db47b31668bb64d996865ceee53bd66b11f.1488285953.git.joe@perches.com
Backmerge the main pull request to sync up with all the newly landed
drivers. Otherwise we'll have chaos even before 4.12 started in
earnest.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
->fault(), ->page_mkwrite(), and ->pfn_mkwrite() calls do not need to
take a vma and vmf parameter when the vma already resides in vmf.
Remove the vma parameter to simplify things.
[arnd@arndb.de: fix ARM build]
Link: http://lkml.kernel.org/r/20170125223558.1451224-1-arnd@arndb.de
Link: http://lkml.kernel.org/r/148521301778.19116.10840599906674778980.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Darrick J. Wong <darrick.wong@oracle.com>
Cc: Matthew Wilcox <mawilcox@microsoft.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Jan Kara <jack@suse.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-----BEGIN PGP SIGNATURE-----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=Yjfg
-----END PGP SIGNATURE-----
Merge tag 'drm-for-v4.11-less-shouty' of git://people.freedesktop.org/~airlied/linux
Pull drm updates from Dave Airlie:
"This is the main drm pull request for v4.11.
Nothing too major, the tinydrm and mmu-less support should make
writing smaller drivers easier for some of the simpler platforms, and
there are a bunch of documentation updates.
Intel grew displayport MST audio support which is hopefully useful to
people, and FBC is on by default for GEN9+ (so people know where to
look for regressions). AMDGPU has a lot of fixes that would like new
firmware files installed for some GPUs.
Other than that it's pretty scattered all over.
I may have a follow up pull request as I know BenH has a bunch of AST
rework and fixes and I'd like to get those in once they've been tested
by AST, and I've got at least one pull request I'm just trying to get
the author to fix up.
Core:
- drm_mm reworked
- Connector list locking and iterators
- Documentation updates
- Format handling rework
- MMU-less support for fbdev helpers
- drm_crtc_from_index helper
- Core CRC API
- Remove drm_framebuffer_unregister_private
- Debugfs cleanup
- EDID/Infoframe fixes
- Release callback
- Tinydrm support (smaller drivers for simple hw)
panel:
- Add support for some new simple panels
i915:
- FBC by default for gen9+
- Shared dpll cleanups and docs
- GEN8 powerdomain cleanup
- DMC support on GLK
- DP MST audio support
- HuC loading support
- GVT init ordering fixes
- GVT IOMMU workaround fix
amdgpu/radeon:
- Power/clockgating improvements
- Preliminary SR-IOV support
- TTM buffer priority and eviction fixes
- SI DPM quirks removed due to firmware fixes
- Powerplay improvements
- VCE/UVD powergating fixes
- Cleanup SI GFX code to match CI/VI
- Support for > 2 displays on 3/5 crtc asics
- SI headless fixes
nouveau:
- Rework securre boot code in prep for GP10x secure boot
- Channel recovery improvements
- Initial power budget code
- MMU rework preperation
vmwgfx:
- Bunch of fixes and cleanups
exynos:
- Runtime PM support for MIC driver
- Cleanups to use atomic helpers
- UHD Support for TM2/TM2E boards
- Trigger mode fix for Rinato board
etnaviv:
- Shader performance fix
- Command stream validator fixes
- Command buffer suballocator
rockchip:
- CDN DisplayPort support
- IOMMU support for arm64 platform
imx-drm:
- Fix i.MX5 TV encoder probing
- Remove lower fb size limits
msm:
- Support for HW cursor on MDP5 devices
- DSI encoder cleanup
- GPU DT bindings cleanup
sti:
- stih410 cleanups
- Create fbdev at binding
- HQVDP fixes
- Remove stih416 chip functionality
- DVI/HDMI mode selection fixes
- FPS statistic reporting
omapdrm:
- IRQ code cleanup
dwi-hdmi bridge:
- Cleanups and fixes
adv-bridge:
- Updates for nexus
sii8520 bridge:
- Add interlace mode support
- Rework HDMI and lots of fixes
qxl:
- probing/teardown cleanups
ZTE drm:
- HDMI audio via SPDIF interface
- Video Layer overlay plane support
- Add TV encoder output device
atmel-hlcdc:
- Rework fbdev creation logic
tegra:
- OF node fix
fsl-dcu:
- Minor fixes
mali-dp:
- Assorted fixes
sunxi:
- Minor fix"
[ This was the "fixed" pull, that still had build warnings due to people
not even having build tested the result. I'm not a happy camper
I've fixed the things I noticed up in this merge. - Linus ]
* tag 'drm-for-v4.11-less-shouty' of git://people.freedesktop.org/~airlied/linux: (1177 commits)
lib/Kconfig: make PRIME_NUMBERS not user selectable
drm/tinydrm: helpers: Properly fix backlight dependency
drm/tinydrm: mipi-dbi: Fix field width specifier warning
drm/tinydrm: mipi-dbi: Silence: ‘cmd’ may be used uninitialized
drm/sti: fix build warnings in sti_drv.c and sti_vtg.c files
drm/amd/powerplay: fix PSI feature on Polars12
drm/amdgpu: refuse to reserve io mem for split VRAM buffers
drm/ttm: fix use-after-free races in vm fault handling
drm/tinydrm: Add support for Multi-Inno MI0283QT display
dt-bindings: Add Multi-Inno MI0283QT binding
dt-bindings: display/panel: Add common rotation property
of: Add vendor prefix for Multi-Inno
drm/tinydrm: Add MIPI DBI support
drm/tinydrm: Add helper functions
drm: Add DRM support for tiny LCD displays
drm/amd/amdgpu: post card if there is real hw resetting performed
drm/nouveau/tmr: provide backtrace when a timeout is hit
drm/nouveau/pci/g92: Fix rearm
drm/nouveau/drm/therm/fan: add a fallback if no fan control is specified in the vbios
drm/nouveau/hwmon: expose power_max and power_crit
..
Pull locking updates from Ingo Molnar:
"The main changes in this cycle were:
- Implement wraparound-safe refcount_t and kref_t types based on
generic atomic primitives (Peter Zijlstra)
- Improve and fix the ww_mutex code (Nicolai Hähnle)
- Add self-tests to the ww_mutex code (Chris Wilson)
- Optimize percpu-rwsems with the 'rcuwait' mechanism (Davidlohr
Bueso)
- Micro-optimize the current-task logic all around the core kernel
(Davidlohr Bueso)
- Tidy up after recent optimizations: remove stale code and APIs,
clean up the code (Waiman Long)
- ... plus misc fixes, updates and cleanups"
* 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (50 commits)
fork: Fix task_struct alignment
locking/spinlock/debug: Remove spinlock lockup detection code
lockdep: Fix incorrect condition to print bug msgs for MAX_LOCKDEP_CHAIN_HLOCKS
lkdtm: Convert to refcount_t testing
kref: Implement 'struct kref' using refcount_t
refcount_t: Introduce a special purpose refcount type
sched/wake_q: Clarify queue reinit comment
sched/wait, rcuwait: Fix typo in comment
locking/mutex: Fix lockdep_assert_held() fail
locking/rtmutex: Flip unlikely() branch to likely() in __rt_mutex_slowlock()
locking/rwsem: Reinit wake_q after use
locking/rwsem: Remove unnecessary atomic_long_t casts
jump_labels: Move header guard #endif down where it belongs
locking/atomic, kref: Implement kref_put_lock()
locking/ww_mutex: Turn off __must_check for now
locking/atomic, kref: Avoid more abuse
locking/atomic, kref: Use kref_get_unless_zero() more
locking/atomic, kref: Kill kref_sub()
locking/atomic, kref: Add kref_read()
locking/atomic, kref: Add KREF_INIT()
...
The field contains a pointer to the parent platform device of the DRM
device. As struct drm_device also contains a dev pointer to the struct
device embedded in the platform_device structure, the platformdev field
is redundant. Remove it and use the dev pointer directly.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Jyri Sarha <jsarha@ti.com>
Acked-by: Vincent Abriou <vincent.abriou@st.com> # For sti
Acked-by: Russell King <rmk+kernel@armlinux.org.uk> # For armada
Acked-by: Rob Clark <robdclark@gmail.com> # For msm
Acked-by: Xinwei Kong<kong.kongxinwei@hisilicon.com>
Core code already makes drm_driver.get_vblank_counter hook optional by
letting drm_vblank_no_hw_counter be the default implementation for the
function hook. So the drm_vblank_no_hw_counter assignment in the driver
code becomes redundant and can be removed now.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Mali DP Maintainers <malidp@foss.arm.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Inki Dae <inki.dae@samsung.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Xinliang Liu <z.liuxinliang@hisilicon.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: CK Hu <ck.hu@mediatek.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Mark Yao <mark.yao@rock-chips.com>
Cc: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Eric Anholt <eric@anholt.net>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Alexey Brodkin <abrodkin@synopsys.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1486458995-31018-3-git-send-email-shawnguo@kernel.org
Noticed that everyone duplicates the same logic here and we could safe
a few lines per driver. Yay for lots of drivers to make such tiny
refactors worth-while!
v2: Forgot to git add everything :(
v3: Actually remove release_fbi (Sean, Emil, Chris) ...
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: Noralf Trønnes <noralf@tronnes.org>
Cc: Emil Velikov <emil.l.velikov@gmail.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170207161603.17611-1-daniel.vetter@ffwll.ch
The big things this time around are:
1) support for hw cursor on newer mdp5 devices (snapdragon 820+,
tested on db820c)
2) dsi encoder cleanup
3) gpu dt bindings cleanup so we can get the gpu nodes merged upstream
* 'msm-next' of git://people.freedesktop.org/~robclark/linux: (32 commits)
drm/msm: return -EFAULT if copy_from_user() fails
drm/msm/dsi: Add PHY/PLL for 8x96
drm/msm/dsi: Add new method to calculate 14nm PHY timings
drm/msm/dsi: Move PHY operations out of host
drm/msm/dsi: Reset both PHYs before clock operation for dual DSI
drm/msm/dsi: Pass down use case to PHY
drm/msm/dsi: Return more timings from PHY to host
drm/msm/dsi: Add a PHY op that initializes version specific stuff
drm/msm/dsi: Add 8x96 info in dsi_cfg
drm/msm/dsi: Don't error if a DSI host doesn't have a device connected
drm/msm/mdp5: Add support for legacy cursor updates
drm/msm/mdp5: Refactor mdp5_plane_atomic_check
drm/msm/mdp5: Add cursor planes
drm/msm/mdp5: Misc cursor plane bits
drm/msm/mdp5: Configure COLOR3_OUT propagation
drm/msm/mdp5: Use plane helpers to configure src/dst rectangles
drm/msm/mdp5: Prepare CRTC/LM for empty stages
drm/msm/mdp5: Create only as many CRTCs as we need
drm/msm/mdp5: cfg: Change count to unsigned int
drm/msm/mdp5: Create single encoder per interface (INTF)
...
copy_from_user_inatomic() is actually a local function that returns
-EFAULT or positive values on error. Otherwise copy_from_user() returns
the number of bytes remaining to be copied. We want to return -EFAULT
here.
I removed an unlikely() because we just did a copy_from_user()
so I don't think it can possibly make a difference.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Extend the DSI PHY/PLL drivers to support the DSI 14nm PHY/PLL
found on 8x96.
These are picked up from the downstream driver. The PHY part is similar
to the other DSI PHYs. The PLL driver requires some trickery so that
one DSI PLL can drive both the DSIs (i.e, dual DSI mode).
In the case of dual DSI mode. One DSI instance becomes the clock master,
and other the clock slave. The master PLL's output (Byte and Pixel clock)
is fed to both the DSI hosts/PHYs.
When the DSIs are configured in dual DSI mode, the PHY driver communicates
to the PLL driver using msm_dsi_pll_set_usecase() which instance is the
master and which one is the slave. When setting rate, the master PLL also
configures some of the slave PLL/PHY registers which need to be identical
to the master's for correct dual DSI behaviour.
There are 2 PLL post dividers that should have ideally been modelled as
generic clk_divider clocks, but require some customization for dual DSI.
In particular, when the master PLL's post-diviers are set, the slave PLL's
post-dividers need to be set too. The clk_ops for these use clk_divider's
helper ops and flags internally to prevent redundant code.
Cc: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The 14nm DSI PHY on 8x96 (called PHY v2 downstream) requires a different
set of calculations for computing D-PHY timing params. Create a
timing_calc_v2 func for the newer v2 PHYs.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Since DSI PHY has been a separate platform device, it should not
depend on the resources in host to be functional. This change is
to trigger PHY operations in manager, instead of host, so that
host and PHY can be completely separated.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
In case of dual DSI, some registers in PHY1 have been programmed
during PLL0 clock's set_rate. The PHY1 reset called by host1 later
will silently reset those PHY1 registers. This change is to reset
and enable both PHYs before any PLL clock operation.
[Originally worked on by Hai Li <hali@codeaurora.org>. Fixed up
by Archit Taneja <architt@codeaurora.org>]
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
For some new types of DSI PHY, more settings depend on
use cases controlled by DSI manager. This change allows
DSI manager to setup PHY with a use case.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The DSI host is required to configure more timings calculated
in PHY. By introducing a shared structure, this change allows
more timing information passed from PHY to host.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Create an init() op for dsi_phy which sets up things specific to
a given DSI PHY.
The dsi_phy driver probe expects every DSI version to get a
"dsi_phy_regulator" mmio base. This isn't the case for 8x96.
Creating an init() op will allow us to accommodate such
differences.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Add 8x96 DSI data in dsi_cfg. The downstream kernel's dsi_host driver
enables core_mmss_clk. We're seeing some branch clock warnings on
8x96 when enabling this. There doesn't seem to be any negative effect
with not enabling this clock, so use it once we figure out why we
get the warnings.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The driver returns an error if a DSI DT node is populated, but no device
is connected to it or if the data-lane map isn't present. Ideally, such
a DSI node shouldn't be probed at all (i.e, its status should be set to
"disabled in DT"), but there isn't any harm in registering the DSI device
even if it doesn't have a bridge/panel connected to it.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
This code has been more or less picked up from the vc4 and intel
implementations of update_plane() funcs for cursor planes.
The update_plane() func is usually the drm_atomic_helper_update_plane
func that will issue an atomic commit with the plane updates. Such
commits are not intended to be done faster than the vsync rate.
The legacy cursor userspace API, on the other hand, expects the kernel
to handle cursor updates immediately.
Create a fast path in update_plane, which updates the cursor registers
and flushes the configuration. The fast path is taken when there is only
a change in the cursor's position in the crtc, or a change in the
cursor's crop co-ordinates. For anything else, we go via the slow path.
We take the slow path even when the fb changes, and when there is
currently no fb tied to the plane. This should hopefully ensure that we
always take a slow path for every new fb. This in turn should ensure that
the fb is pinned/prepared.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
In mdp5_plane_atomic_check, we get crtc_state from drm_plane_state.
Later, for cursor planes, we'll populate the update_plane() func that
takes a fast asynchronous path to implement cursor movements. There, we
would need to call a similar atomic_check func to validate the plane
state, but crtc_state would need to be derived differently.
Refactor mdp5_plane_atomic_check to mdp5_plane_atomic_check_with_state
such that the latter takes crtc_state as an argument.
This is similar to what the intel driver has done for async cursor
updates.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Register cursor drm_planes. The loop in modeset_init that inits the
planes and crtcs has to be refactored a bit. We first iterate all the
hwpipes to find the cursor planes. Then, we loop again to create
crtcs.
In msm_atomic_wait_for_commit_done, remove the check which bypasses
waiting for vsyncs if state->legacy_cursor_updates is true.
We will later create a fast path for cursor position changes in the
cursor plane's update_plane func that doesn't go via the regular
atomic commit path. For rest of cursor related updates, we will have
to wait for vsyncs, so ignore the legacy_cursor_updates flag.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
These are various changes added in preparation for cursor planes:
- Add a pipe_cursor block for 8x96 in mdp5_cfg.
- Add a new pipe CAP called MDP_PIPE_CAP_CURSOR. Use this to ensure we
assign a cursor SSPP for a drm_plane with type DRM_PLANE_TYPE_CURSOR.
- Update mdp5_ctl_blend_mask/ext_blend_mask funcs to incorporate cursor
SSPPs.
- In mdp5_ctl_blend, iterate through MAX_STAGES instead of stage_cnt,
we need to do this because we can now have empty stages in between.
- In mdp5_crtc_atomic_check, make sure that the cursor plane has the
highest zorder, and stage the cursor plane to the maximum stage #
present on the HW.
- Create drm_crtc_funcs that doesn't try to implement cursors using the
older LM cursor HW.
- Pass drm_plane_type in mdp5_plane_init instead of a bool telling
whether plane is primary or not.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
In MDP5 Layer Mixer HW, the blender output is only the blended color
components (i.e R, G and B, or COLOR0/1/2 in MDP5 HW terminology). This
is fed to the BG input of the next blender. We also need to provide an
alpha (COLOR3) value for the BG input at the next stage.
This is configured via using the REG_MDP5_LM_BLEND_COLOR_OUT register.
For each stage, we can propagate either the BG or FG alpha to the next
stage.
The approach taken by the driver is to propagate FG alpha, if the plane
staged on that blender has an alpha. If it doesn't, we try to propagate
the base layer's alpha.
This is borrowed from downstream MDP5 kernel driver. Without this, we
don't see any cursor plane content.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The MDP5 plane's atomic_check ops doesn't perform clipping tests.
This didn't hurt us much in the past, but clipping becomes important
with cursor planes.
Use drm_plane_helper_check_state, the way rockchip/intel/mtk drivers
already do. Use these drivers as reference.
Clipping requires knowledge of the crtc width and height. This requires
us to call drm_atomic_helper_check_modeset before
drm_atomic_helper_check_planes in the driver's atomic_check op, because
check_modetest will populate the mode for the crtc, needed to populate
the clip rectangle.
We update the plane_enabled(state) local helper to use state->visible,
since state->visible and 'state->fb && state->crtc' represent the same
thing.
One issue with the existing code is that we don't have a way to disable
the plane when it's completely clipped out. Until there isn't an update
on the crtc (which would de-stage the plane), we would still see the
plane in its last 'visible' configuration.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Use SSPP_NONE in mdp5_plane_pipe() if there is now hwpipe allocated for
the drm_plane. Returning '0' means we are returning VIG0 pipe.
Also, use the mdp5_pipe enum to pass around the stage array. Initialize
the stage to SSPP_NONE by default.
We do the above because 1) Cursor plane has to be staged at the topmost
blender of the LM, which can result in empty stages in between 2) In
the future, when we support multiple LMs per CRTC. We could have stages
which don't have any pipe assigned to them.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
We currently create CRTCs equaling to the # of Layer Mixer blocks we
have on the MDP5 HW. This number is generally more than the # of encoders
(INTFs) we have in the MDSS HW. The number of encoders connected to
displays on the platform (as described by DT) would be even lesser.
Create only N drm_crtcs, where N is the number of drm_encoders
successfully registered. To do this, we call modeset_init_intf() before
we init the drm_crtcs and drm_planes.
Because of this change, setting encoder->possible_crtcs needs to be moved
from construct_encoder() to a later point when we know how many CRTCs we
have.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Count can't be non-zero. Changing to uint will also prevent future
warnings.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
For the DSI interfaces, the mdp5_kms core creates 2 encoders for video
and command modes.
Create only a single encoder per interface. When creating the encoder, set
the interface type to MDP5_INTF_MODE_NONE. It's the bridge (DSI/HDMI/eDP)
driver's responsibility to set a different interface type. It can use the
the kms func op set_encoder_mode to change the mode of operation, which
in turn would configure the interface type for the INTF.
In mdp5_cmd_encoder.c, we remove the redundant code, and make the commmand
mode funcs as helpers that are used in mdp5_encoder.c
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Rename the mdp5_encoder_* ops for active displays to
mdp5_vid_encoder_* ops.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The mdp5 kms driver currently sets up multiple encoders per interface
(INTF), one for each kind of mode of operation it supports.
We create 2 drm_encoders for DSI, one for Video Mode and the other
for Command Mode operation. The reason behind this approach could have
been that we aren't aware of the DSI device's mode of operation when
we create the encoders.
This makes things a bit complicated, since these encoders have to
be further attached to the same DSI bridge. The easier way out is
to create a single encoder, and make the DSI driver set its mode
of operation when we know what the DSI device's mode flags are.
Start with providing a way to set the mdp5_intf_mode using a kms
func that sets the encoder's mode of operation. When constructing
a DSI encoder, we set the mode of operation to Video Mode as
default. When the DSI device is attached to the host, we probe the
DSI mode flags and set the corresponding mode of operation.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
We currently create 2 encoders for DSI interfaces, one for command
mode and other for video mode operation. This isn't needed as we
can't really use both the encoders at the same time. It also makes
connecting bridges harder.
Switch to creating a single encoder. For now, we assume that the
encoder is configured only in video mode. Later, the same encoder
would be usable in both modes.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The commit "drm: bridge: Link encoder and bridge in core code" updated
the drm_bridge_attach() API to also include the drm_encoder pointer
the bridge attaches to.
The func msm_dsi_manager_bridge_init() now relies on the drm_encoder
pointer stored in msm_dsi->encoders to pass the encoder to the bridge
API.
msm_dsi->encoders is unfortunately set after this function is called,
resulting in us passing a NULL pointer to drm_brigde_attach. This
results in an error and the DSI driver probe fails.
Move the initialization of msm_dsi->encoders[] a bit up. Also, don't
try to set the encoder's bridge. That's now managed by the bridge
API.
Cc: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Define the block in advance so that the generated mdp5.xml.h doesn't
break build.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Suggested by Rob Herring. We still support the old names for
compatibility with downstream android dt files.
Cc: Rob Herring <robh@kernel.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Acked-by: Rob Herring <robh@kernel.org>
This was never documented or used in upstream dtb. It is used by
downstream bindings from android device kernels. But the quirks are
a property of the gpu revision, and as such are redundant to be listed
separately in dt. Instead, move the quirks to the device table.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
The original way we determined the gpu version was based on downstream
bindings from android kernel. A cleaner way is to get the version from
the compatible string.
Note that no upstream dtb uses these bindings. But the code still
supports falling back to the legacy bindings (with a warning), so that
we are still compatible with the gpu dt node from android device
kernels.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Acked-by: Rob Herring <robh@kernel.org>
The plan is to use the OPP bindings. For now, remove the documentation
for qcom,gpu-pwrlevels, and make the driver fall back to a safe low
clock if the node is not present.
Note that no upstream dtb use this node. For now we keep compatibility
with this node to avoid breaking compatibility with downstream android
dt files.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Acked-by: Rob Herring <robh@kernel.org>
The drm_mm range manager claimed to support top-down insertion, but it
was neither searching for the top-most hole that could fit the
allocation request nor fitting the request to the hole correctly.
In order to search the range efficiently, we create a secondary index
for the holes using either their size or their address. This index
allows us to find the smallest hole or the hole at the bottom or top of
the range efficiently, whilst keeping the hole stack to rapidly service
evictions.
v2: Search for holes both high and low. Rename flags to mode.
v3: Discover rb_entry_safe() and use it!
v4: Kerneldoc for enum drm_mm_insert_mode.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Christian Gmeiner <christian.gmeiner@gmail.com>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: Sinclair Yeh <syeh@vmware.com>
Cc: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com> # vmwgfx
Reviewed-by: Lucas Stach <l.stach@pengutronix.de> #etnaviv
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170202210438.28702-1-chris@chris-wilson.co.uk
Instead of receiving the num_crts as a parameter, we can read it
directly from the mode_config structure. I audited the drivers that
invoke this helper and I believe all of them initialize the mode_config
struct accordingly, prior to calling the fb_helper.
I used the following coccinelle hack to make this transformation, except
for the function headers and comment updates. The first and second
rules are split because I couldn't find a way to remove the unused
temporary variables at the same time I removed the parameter.
// <smpl>
@r@
expression A,B,D,E;
identifier C;
@@
(
- drm_fb_helper_init(A,B,C,D)
+ drm_fb_helper_init(A,B,D)
|
- drm_fbdev_cma_init_with_funcs(A,B,C,D,E)
+ drm_fbdev_cma_init_with_funcs(A,B,D,E)
|
- drm_fbdev_cma_init(A,B,C,D)
+ drm_fbdev_cma_init(A,B,D)
)
@@
expression A,B,C,D,E;
@@
(
- drm_fb_helper_init(A,B,C,D)
+ drm_fb_helper_init(A,B,D)
|
- drm_fbdev_cma_init_with_funcs(A,B,C,D,E)
+ drm_fbdev_cma_init_with_funcs(A,B,D,E)
|
- drm_fbdev_cma_init(A,B,C,D)
+ drm_fbdev_cma_init(A,B,D)
)
@@
identifier r.C;
type T;
expression V;
@@
- T C;
<...
when != C
- C = V;
...>
// </smpl>
Changes since v1:
- Rebased on top of the tip of drm-misc-next.
- Remove mention to sti since a proper fix got merged.
Suggested-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Gabriel Krisman Bertazi <krisman@collabora.co.uk>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170202162640.27261-1-krisman@collabora.co.uk
- cleanups&fixes for dw-hdmi bride driver (Laurent)
- updates for adv bridge driver (John Stultz) for nexus
- drm_crtc_from_index helper rollout (Shawn Guo)
- removing drm_framebuffer_unregister_private from drivers&core
- target_vblank (Andrey Grodzovsky)
- misc tiny stuff
* tag 'drm-misc-next-2017-01-23' of git://anongit.freedesktop.org/git/drm-misc: (49 commits)
drm: qxl: Open code teardown function for qxl
drm: qxl: Open code probing sequence for qxl
drm/bridge: adv7511: Re-write the i2c address before EDID probing
drm/bridge: adv7511: Reuse __adv7511_power_on/off() when probing EDID
drm/bridge: adv7511: Rework adv7511_power_on/off() so they can be reused internally
drm/bridge: adv7511: Enable HPD interrupts to support hotplug and improve monitor detection
drm/bridge: adv7511: Switch to using drm_kms_helper_hotplug_event()
drm/bridge: adv7511: Use work_struct to defer hotplug handing to out of irq context
drm: vc4: use crtc helper drm_crtc_from_index()
drm: tegra: use crtc helper drm_crtc_from_index()
drm: nouveau: use crtc helper drm_crtc_from_index()
drm: mediatek: use crtc helper drm_crtc_from_index()
drm: kirin: use crtc helper drm_crtc_from_index()
drm: exynos: use crtc helper drm_crtc_from_index()
dt-bindings: display: dw-hdmi: Clean up DT bindings documentation
drm: bridge: dw-hdmi: Assert SVSRET before resetting the PHY
drm: bridge: dw-hdmi: Fix the name of the PHY reset macros
drm: bridge: dw-hdmi: Define and use macros for PHY register addresses
drm: bridge: dw-hdmi: Detect PHY type at runtime
drm: bridge: dw-hdmi: Handle overflow workaround based on device version
...
Backmerge Linus master to get the connector locking revert.
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux: (645 commits)
sysctl: fix proc_doulongvec_ms_jiffies_minmax()
Revert "drm/probe-helpers: Drop locking from poll_enable"
MAINTAINERS: add Dan Streetman to zbud maintainers
MAINTAINERS: add Dan Streetman to zswap maintainers
mm: do not export ioremap_page_range symbol for external module
mn10300: fix build error of missing fpu_save()
romfs: use different way to generate fsid for BLOCK or MTD
frv: add missing atomic64 operations
mm, page_alloc: fix premature OOM when racing with cpuset mems update
mm, page_alloc: move cpuset seqcount checking to slowpath
mm, page_alloc: fix fast-path race with cpuset update or removal
mm, page_alloc: fix check for NULL preferred_zone
kernel/panic.c: add missing \n
fbdev: color map copying bounds checking
frv: add atomic64_add_unless()
mm/mempolicy.c: do not put mempolicy before using its nodemask
radix-tree: fix private list warnings
Documentation/filesystems/proc.txt: add VmPin
mm, memcg: do not retry precharge charges
proc: add a schedule point in proc_pid_readdir()
...
Since we need to change the implementation, stop exposing internals.
Provide kref_read() to read the current reference count; typically
used for debug messages.
Kills two anti-patterns:
atomic_read(&kref->refcount)
kref->refcount.counter
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Fixes: 9cb07b099fb ("drm/msm: support multiple address spaces")
Reported-by: Riku Voipio <riku.voipio@linaro.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
It would race between userspace thread and commit worker. Ie. vblank
irq would trigger event and userspace could begin the next atomic
update, before the commit worker had a chance to clear the pending
flag.
If we do end up needing something to prevent userspace from trying
another pageflip before getting vblank event, it should probably be
implemented as a pending_planes bitmask, similar to pending_crtcs. See
start_atomic() and end_atomic().
Signed-off-by: Rob Clark <robdclark@gmail.com>
This is the deprecated function for when you embedded the framebuffer
somewhere else (which breaks refcounting). But msm is using
drm_framebuffer_remove and a free-standing fb, so this is rendundant.
Cc: Rob Clark <robdclark@gmail.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1482835765-12044-1-git-send-email-daniel.vetter@ffwll.ch
Many DRM drivers only work with an MMU, and after the patch to enable
core DRM support without MMU, we already had one fixup for many of them.
The etnaviv, armada and msm drivers were missed and have the same problem:
warning: (DRM_ETNAVIV) selects IOMMU_SUPPORT which has unmet direct dependencies (MMU)
warning: (DRM_I915 && DRM_MSM && DRM_ETNAVIV) selects SHMEM which has unmet direct dependencies (MMU)
drivers/gpu/drm/armada/armada_gem.o: In function `armada_gem_vm_fault':
armada_gem.c:(.text.armada_gem_vm_fault+0x14): undefined reference to `vm_insert_pfn'
arch/arm/mm/dma-mapping.c: In function '__iommu_alloc_remap':
arch/arm/mm/dma-mapping.c:1390:4: error: 'VM_ARM_DMA_CONSISTENT' undeclared (first use in this function)
arch/arm/mm/dma-mapping.c:1456:31: error: 'atomic_pool' undeclared (first use in this function); did you mean 'atomic_xor'?
Fixes: 011cda5899 ("drm: fix compilations issues introduced by "drm: allow to use mmuless SoC"")
Fixes: 62a0d98a18 ("drm: allow to use mmuless SoC")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170111133357.3664191-2-arnd@arndb.de
Back to regular -misc pulls with reasonable sizes:
- dma_fence error clarification (Chris)
- drm_crtc_from_index helper (Shawn), pile more patches on the m-l to roll
this out to drivers
- mmu-less support for fbdev helpers from Benjamin
- piles of kerneldoc work
- some polish for crc support from Tomeu and Benjamin
- odd misc stuff all over
* tag 'drm-misc-next-2017-01-09' of git://anongit.freedesktop.org/git/drm-misc: (48 commits)
dma-fence: Introduce drm_fence_set_error() helper
dma-fence: Wrap querying the fence->status
dma-fence: Clear fence->status during dma_fence_init()
drm: fix compilations issues introduced by "drm: allow to use mmuless SoC"
drm: Change the return type of the unload hook to void
drm: add more document for drm_crtc_from_index()
drm: remove useless parameters from drm_pick_cmdline_mode function
drm: crc: Call wake_up_interruptible() each time there is a new CRC entry
drm: allow to use mmuless SoC
drm: compile drm_vm.c only when needed
fbmem: add a default get_fb_unmapped_area function
drm: crc: Wait for a frame before returning from open()
drm: Move locking into drm_debugfs_crtc_crc_add
drm/imx: imx-tve: Remove unused variable
Revert "drm: nouveau: fix build when LEDS_CLASS=m"
drm: Add kernel-doc for drm_crtc_commit_get/put
drm/atomic: Fix outdated comment.
drm: reference count event->completion
gpu: drm: mgag200: mgag200_main:- Handle error from pci_iomap
drm: Document deprecated load/unload hook
...
First -misc pull for 4.11:
- drm_mm rework + lots of selftests (Chris Wilson)
- new connector_list locking+iterators
- plenty of kerneldoc updates
- format handling rework from Ville
- atomic helper changes from Maarten for better plane corner-case handling
in drivers, plus the i915 legacy cursor patch that needs this
- bridge cleanup from Laurent
- plus plenty of small stuff all over
- also contains a merge of the 4.10 docs tree so that we could apply the
dma-buf kerneldoc patches
It's a lot more than usual, but due to the merge window blackout it also
covers about 4 weeks, so all in line again on a per-week basis. The more
annoying part with no pull request for 4 weeks is managing cross-tree
work. The -intel pull request I'll follow up with does conflict quite a
bit with -misc here. Longer-term (if drm-misc keeps growing) a
drm-next-queued to accept pull request for the next merge window during
this time might be useful.
I'd also like to backmerge -rc2+this into drm-intel next week, we have
quite a pile of patches waiting for the stuff in here.
* tag 'drm-misc-next-2016-12-30' of git://anongit.freedesktop.org/git/drm-misc: (126 commits)
drm: Add kerneldoc markup for new @scan parameters in drm_mm
drm/mm: Document locking rules
drm: Use drm_mm_insert_node_in_range_generic() for everyone
drm: Apply range restriction after color adjustment when allocation
drm: Wrap drm_mm_node.hole_follows
drm: Apply tight eviction scanning to color_adjust
drm: Simplify drm_mm scan-list manipulation
drm: Optimise power-of-two alignments in drm_mm_scan_add_block()
drm: Compute tight evictions for drm_mm_scan
drm: Fix application of color vs range restriction when scanning drm_mm
drm: Unconditionally do the range check in drm_mm_scan_add_block()
drm: Rename prev_node to hole in drm_mm_scan_add_block()
drm: Fix O= out-of-tree builds for selftests
drm: Extract struct drm_mm_scan from struct drm_mm
drm: Add asserts to catch overflow in drm_mm_init() and drm_mm_init_scan()
drm: Simplify drm_mm_clean()
drm: Detect overflow in drm_mm_reserve_node()
drm: Fix kerneldoc for drm_mm_scan_remove_block()
drm: Promote drm_mm alignment to u64
drm: kselftest for drm_mm and restricted color eviction
...
Including all drivers. I thought about keeping small compat functions
to avoid having to change all drivers. But I really like the
drm_printer idea, so figured spreading it more widely is a good thing.
v2: Review from Chris:
- Natural argument order and better name for drm_mm_print.
- show_mm() macro in the selftest.
Cc: Rob Clark <robdclark@gmail.com>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Christian König <christian.koenig@amd.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1483009764-8281-1-git-send-email-daniel.vetter@ffwll.ch
For every submission buffer object one of MSM_SUBMIT_BO_WRITE
and MSM_SUBMIT_BO_READ must be set (and nothing else). If we
allowed zero then the buffer object would never get queued to
be unreferenced.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The error cases in submit_reloc() need to put back the virtual
address of the bo before failling. Add a single failure path
for the function.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Currently the value written to CP_RB_WPTR is calculated on the fly as
(rb->next - rb->start). But as the code is designed rb->next is wrapped
before writing the commands so if a series of commands happened to
fit perfectly in the ringbuffer, rb->next would end up being equal to
rb->size / 4 and thus result in an out of bounds address to CP_RB_WPTR.
The easiest way to fix this is to mask WPTR when writing it to the
hardware; it makes the hardware happy and the rest of the ringbuffer
math appears to work and there isn't any point in upsetting anything.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
[squash in is_power_of_2() check]
Signed-off-by: Rob Clark <robdclark@gmail.com>
Instead of linking encoders and bridges in every driver (and getting it
wrong half of the time, as many drivers forget to set the drm_bridge
encoder pointer), do so in core code. The drm_bridge_attach() function
needs the encoder and optional previous bridge to perform that task,
update all the callers.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Stefan Agner <stefan@agner.ch> # For DCU
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com> # For atmel-hlcdc
Acked-by: Vincent Abriou <vincent.abriou@st.com> # For STI
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> # For sun4i
Acked-by: Xinliang Liu <z.liuxinliang@hisilicon.com> # For hisilicon
Acked-by: Jyri Sarha <jsarha@ti.com> # For tilcdc
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1481709550-29226-4-git-send-email-laurent.pinchart+renesas@ideasonboard.com
Every single user of vmf->virtual_address typed that entry to unsigned
long before doing anything with it so the type of virtual_address does
not really provide us any additional safety. Just use masked
vmf->address which already has the appropriate type.
Link: http://lkml.kernel.org/r/1479460644-25076-3-git-send-email-jack@suse.cz
Signed-off-by: Jan Kara <jack@suse.cz>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-----BEGIN PGP SIGNATURE-----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=7s/c
-----END PGP SIGNATURE-----
Merge tag 'drm-for-v4.10' of git://people.freedesktop.org/~airlied/linux
Pull drm updates from Dave Airlie:
"This is the main pull request for drm for 4.10 kernel.
New drivers:
- ZTE VOU display driver (zxdrm)
- Amlogic Meson Graphic Controller GXBB/GXL/GXM SoCs (meson)
- MXSFB support (mxsfb)
Core:
- Format handling has been reworked
- Better atomic state debugging
- drm_mm leak debugging
- Atomic explicit fencing support
- fbdev helper ops
- Documentation updates
- MST fbcon fixes
Bridge:
- Silicon Image SiI8620 driver
Panel:
- Add support for new simple panels
i915:
- GVT Device model
- Better HDMI2.0 support on skylake
- More watermark fixes
- GPU idling rework for suspend/resume
- DP Audio workarounds
- Scheduler prep-work
- Opregion CADL handling
- GPU scheduler and priority boosting
amdgfx/radeon:
- Support for virtual devices
- New VM manager for non-contig VRAM buffers
- UVD powergating
- SI register header cleanup
- Cursor fixes
- Powermanagement fixes
nouveau:
- Powermangement reworks for better voltage/clock changes
- Atomic modesetting support
- Displayport Multistream (MST) support.
- GP102/104 hang and cursor fixes
- GP106 support
hisilicon:
- hibmc support (BMC chip for aarch64 servers)
armada:
- add tracing support for overlay change
- refactor plane support
- de-midlayer the driver
omapdrm:
- Timing code cleanups
rcar-du:
- R8A7792/R8A7796 support
- Misc fixes.
sunxi:
- A31 SoC display engine support
imx-drm:
- YUV format support
- Cleanup plane atomic update
mali-dp:
- Misc fixes
dw-hdmi:
- Add support for HDMI i2c master controller
tegra:
- IOMMU support fixes
- Error handling fixes
tda998x:
- Fix connector registration
- Improved robustness
- Fix infoframe/audio compliance
virtio:
- fix busid issues
- allocate more vbufs
qxl:
- misc fixes and cleanups.
vc4:
- Fragment shader threading
- ETC1 support
- VEC (tv-out) support
msm:
- A5XX GPU support
- Lots of atomic changes
tilcdc:
- Misc fixes and cleanups.
etnaviv:
- Fix dma-buf export path
- DRAW_INSTANCED support
- fix driver on i.MX6SX
exynos:
- HDMI refactoring
fsl-dcu:
- fbdev changes"
* tag 'drm-for-v4.10' of git://people.freedesktop.org/~airlied/linux: (1343 commits)
drm/nouveau/kms/nv50: fix atomic regression on original G80
drm/nouveau/bl: Do not register interface if Apple GMUX detected
drm/nouveau/bl: Assign different names to interfaces
drm/nouveau/bios/dp: fix handling of LevelEntryTableIndex on DP table 4.2
drm/nouveau/ltc: protect clearing of comptags with mutex
drm/nouveau/gr/gf100-: handle GPC/TPC/MPC trap
drm/nouveau/core: recognise GP106 chipset
drm/nouveau/ttm: wait for bo fence to signal before unmapping vmas
drm/nouveau/gr/gf100-: FECS intr handling is not relevant on proprietary ucode
drm/nouveau/gr/gf100-: properly ack all FECS error interrupts
drm/nouveau/fifo/gf100-: recover from host mmu faults
drm: Add fake controlD* symlinks for backwards compat
drm/vc4: Don't use drm_put_dev
drm/vc4: Document VEC DT binding
drm/vc4: Add support for the VEC (Video Encoder) IP
drm: Add TV connector states to drm_connector_state
drm: Turn DRM_MODE_SUBCONNECTOR_xx definitions into an enum
drm/vc4: Fix ->clock_select setting for the VEC encoder
drm/amdgpu/dce6: Set MASTER_UPDATE_MODE to 0 in resume_mc_access as well
drm/amdgpu: use pin rather than pin_restricted in a few cases
...
On the userspace side, all the basics are working, and most of glmark2
is working. I've been working through deqp, and I've got a couple more
things to fix (but we've gone from 70% to 80+% pass in last day, and
current deqp run that is going should pick up another 5-10%). I expect
to push the mesa patches today or tomorrow.
There are a couple more a5xx related patches to take the gpu out of
secure mode (for the devices that come up in secure mode, like the hw
I have), but those depend on an scm patch that would come in through
another tree. If that can land in the next day or two, there might
be a second late pull request for drm/msm.
In addition to the new-shiny, there have also been a lot of overlay/
plane related fixes for issues found using drm-hwc2 (in the process of
testing/debugging the atomic/kms fence patches), resulting in rework
to assign hwpipes to kms planes dynamically (as part of global atomic
state) and also handling SMP (fifo) block allocation atomically as
part of the ->atomic_check() step. All those patches should also help
out atomic weston (when those patches eventually land).
* 'msm-next' of git://people.freedesktop.org/~robclark/linux: (36 commits)
drm/msm: gpu: Add support for the GPMU
drm/msm: gpu: Add A5XX target support
drm/msm: Disable interrupts during init
drm/msm: Remove 'src_clk' from adreno configuration
drm/msm: gpu: Add OUT_TYPE4 and OUT_TYPE7
drm/msm: Add adreno_gpu_write64()
drm/msm: gpu Add new gpu register read/write functions
drm/msm: gpu: Return error on hw_init failure
drm/msm: gpu: Cut down the list of "generic" registers to the ones we use
drm/msm: update generated headers
drm/msm/adreno: move scratch register dumping to per-gen code
drm/msm/rd: support for 64b iova
drm/msm: convert iova to 64b
drm/msm: set dma_mask properly
drm/msm: Remove bad calls to of_node_put()
drm/msm/mdp5: move LM bounds check into plane->atomic_check()
drm/msm/mdp5: dump smp state on errors too
drm/msm/mdp5: add debugfs to show smp block status
drm/msm/mdp5: handle SMP block allocations "atomically"
drm/msm/mdp5: dynamically assign hw pipes to planes
...
Big thing is that drm-misc is now officially a group maintainer/committer
model thing, with MAINTAINERS suitably updated. Otherwise just the usual
pile of misc things all over, nothing that stands out this time around.
* tag 'drm-misc-next-2016-11-29' of git://anongit.freedesktop.org/git/drm-misc: (33 commits)
drm: Introduce drm_framebuffer_assign()
drm/bridge: adv7511: Enable the audio data and clock pads on adv7533
drm/bridge: adv7511: Add Audio support
drm/edid: Consider alternate cea timings to be the same VIC
drm/atomic: Constify drm_atomic_crtc_needs_modeset()
drm: bridge: dw-hdmi: add ASoC dependency
drm: Fix shift operations for drm_fb_helper::drm_target_preferred()
drm: Avoid NULL dereference for DRM_LEGACY debug message
drm: Use u64_to_user_ptr() helper for blob ioctls
drm: Fix conflicting macro parameter in drm_mm_for_each_node_in_range()
drm: Fixup kernel doc for driver->gem_create_object
drm/hisilicon/hibmc: mark PM functions __maybe_unused
drm/hisilicon/hibmc: Checking for NULL instead of IS_ERR()
drm: bridge: add DesignWare HDMI I2S audio support
drm: Check against color expansion in drm_mm_reserve_node()
drm: Define drm_mm_for_each_node_in_range()
drm/doc: Fix links in drm_property.c
MAINTAINERS: Add link to drm-misc documentation
vgaarb: use valid dev pointer in vgaarb_info()
drm/atomic: Unconfuse the old_state mess in commmit_tail
...
drm/qxl: various bugfixes and cleanups,
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQIcBAABAgAGBQJYMzLfAAoJEEy22O7T6HE41rIQANAEl/o8cYUoyYTJlhmmnl2U
K+QBdr7PACdbr8RZrGpwA5ad9ZJGijpZRd2gThrzNS0JBdZI48gPEzU7V206xlyD
AriBeAu6IkoBTEl+GGx2DfvOdLR6+7KlIrDYIpl2vILgkqlHhneXdHR3R03byRHG
2Jrxv2YQxCs8swtAb8FRkVNaUgrfkKOKFFlx1LoLFApYeP02oSxZp0Ve4nuRNj7x
9DCivIw4NyQ9tY1fORapmrEPTerqZnzYdb9RFSv4xilx4Stq1UWdXfTSpwXZHZaG
VroXZb1I0fZEk1aapIxuzLZFGNSM7wLET/nK02sSvzxJJv2PiyVAabIo70nUqsQK
H/iGT2g4MZC1Yvz6evENtckbiA1p3F9jnd+Po9ivDY/RrTpND3hVC2WbcOXWxZkb
m69muvXfrnZwoF9xWPG8aTrCATim++1Ty8/8LoKdVq1d0Dp/Gzk8KnklBPY2vRFt
dpxqH3jLgED/QcO5W/yQdf0kPRsrNwKFNLqP9bCF2hMIw1VHHddZtnBBXDGATXYq
hdFA8EEg3gh/kY7V8b+GyxjRKRbveG208hu+H4EirxHmRn5xJN1VoTLk9va+AJL1
I30l4USLDkTgf1AjYmk7yFIUTemCtwjfa0lsuu4l3rRJ3k1eBrtZe2cpWv2BoQDU
by0sNnDelzJTQ9/v1i3J
=OYiT
-----END PGP SIGNATURE-----
Merge tag 'drm-qemu-20161121' of git://git.kraxel.org/linux into drm-next
drm/virtio: fix busid in a different way, allocate more vbufs.
drm/qxl: various bugfixes and cleanups,
* tag 'drm-qemu-20161121' of git://git.kraxel.org/linux: (224 commits)
drm/virtio: allocate some extra bufs
qxl: Allow resolution which are not multiple of 8
qxl: Don't notify userspace when monitors config is unchanged
qxl: Remove qxl_bo_init() return value
qxl: Call qxl_gem_{init, fini}
qxl: Add missing '\n' to qxl_io_log() call
qxl: Remove unused prototype
qxl: Mark some internal functions as static
Revert "drm: virtio: reinstate drm_virtio_set_busid()"
drm/virtio: fix busid regression
drm: re-export drm_dev_set_unique
Linux 4.9-rc5
gp8psk: Fix DVB frontend attach
gp8psk: fix gp8psk_usb_in_op() logic
dvb-usb: move data_mutex to struct dvb_usb_device
iio: maxim_thermocouple: detect invalid storage size in read()
aoe: fix crash in page count manipulation
lightnvm: invalid offset calculation for lba_shift
Kbuild: enable -Wmaybe-uninitialized warnings by default
pcmcia: fix return value of soc_pcmcia_regulator_set
...
Most 5XX targets have GPMU (Graphics Power Management Unit) that
handles a lot of the heavy lifting for power management including
thermal and limits management and dynamic power collapse. While
the GPMU itself is optional, it is usually nessesary to hit
aggressive power targets.
The GPMU firmware needs to be loaded into the GPMU at init time via a
shared hardware block of registers. Using the GPU to write the microcode
is more efficient than using the CPU so at first load create an indirect
buffer that can be executed during subsequent initalization sequences.
After loading the GPMU gets initalized through a shared register
interface and then we mostly get out of its way and let it do
its thing.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Disable the interrupt during the init sequence to avoid having
interrupts fired for errors and other things that we are not
ready to handle while initializing.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The adreno code inherited a silly workaround from downstream
from the bad old days before decent clock control. grp_clk[0]
(named 'src_clk') doesn't actually exist - it was used as a proxy
for whatever the core clock actually was (usually 'core_clk').
All targets should be able to correctly request 'core_clk' and
get the right thing back so zap the anachronism and directly
use grp_clk[0] to control the clock rate.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Add helper functions for TYPE4 and TYPE7 ME opcodes that replace
TYPE0 and TYPE3 starting with the A5XX targets.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Add a new generic function to write a "64" bit value. This isn't
actually a 64 bit operation, it just writes the upper and lower
32 bit of a 64 bit value to a specified LO and HI register. If
a particular target doesn't support one of the registers it can
mark that register as SKIP and writes/reads from that register
will be quietly dropped.
This can be immediately put in place for the ringbuffer base and
the RPTR address. Both writes are converted to use
adreno_gpu_write64() with their respective high and low registers
and the high register appropriately marked as SKIP for both 32 bit
targets (a3xx and a4xx). When a5xx comes it will define valid target
registers for the 'hi' option and everything else will just work.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Add some new functions to manipulate GPU registers. gpu_read64 and
gpu_write64 can read/write a 64 bit value to two 32 bit registers.
For 4XX and older these are normally perfcounter registers, but
future targets will use 64 bit addressing so there will be many
more spots where a 64 bit read and write are needed.
gpu_rmw() does a read/modify/write on a 32 bit register given a mask
and bits to OR in.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
When the GPU hardware init function fails (like say, ME_INIT timed
out) return error instead of blindly continuing on. This gives us
a small chance of saving the system before it goes boom.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
There are very few register accesses in the common code. Cut down
the list of common registers to just those that are used. This
saves const space and saves us the effort of maintaining registers
for A3XX and A4XX that don't exist or are unused.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
For a5xx the gpu is 64b so we need to change iova to 64b everywhere. On
the display side, iova is still 32b so it can ignore the upper bits.
(Although all the armv8 devices have an iommu that can map 64b pa to 32b
iova.)
Signed-off-by: Rob Clark <robdclark@gmail.com>
Previous value really only made sense on armv7 without LPAE. Everything
that supports more than 4g of memory also has iommu's that can map
anything.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Jordan Crouse