CPU hotplug and kexec rely on smp_ops.cpu_kill(), which is supposed
to wait for the CPU to park or power down, and perform the last
rites (such as disabling clocks etc., where the platform doesn't do
this automatically).
kexec in particular is unsafe without performing this
synchronisation to park secondaries. Without it, the secondaries
might not be parked when kexec trashes the kernel.
There is no generic way to do this synchronisation, so a new mcpm
platform_ops method power_down_finish() is added by this patch.
The new method is mandatory. A platform which provides no way to
detect when CPUs are parked is likely broken.
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Reviewed-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch factors the logical-to-physical CPU translation out of
mcpm_boot_secondary(), so that it can be reused elsewhere.
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch proposes to remove the use of the IRQF_DISABLED flag
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move some of the OMAP2+ CM and System Control Module direct
register accesses into CM- and System Control
Module-specific "drivers" underneath arch/arm/mach-omap2/. This
is a prerequisite for moving this code out of arch/arm/mach-omap2/ into
drivers/.
Basic test logs are available here:
http://www.pwsan.com/omap/testlogs/cm_scm_cleanup_a_v3.13/20131019101809/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=L37r
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.13/cm-scm-cleanup-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/cleanup
From Paul Walmsley <paul@pwsan.com> via Tony Lindgren:
Move some of the OMAP2+ CM and System Control Module direct
register accesses into CM- and System Control
Module-specific "drivers" underneath arch/arm/mach-omap2/. This
is a prerequisite for moving this code out of arch/arm/mach-omap2/ into
drivers/.
Basic test logs are available here:
http://www.pwsan.com/omap/testlogs/cm_scm_cleanup_a_v3.13/20131019101809/
* tag 'omap-for-v3.13/cm-scm-cleanup-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP3: control: add API for setting IVA bootmode
ARM: OMAP3: CM/control: move CM scratchpad save to CM driver
ARM: OMAP3: McBSP: do not access CM register directly
ARM: OMAP3: clock: add API to enable/disable autoidle for a single clock
ARM: OMAP2: CM/PM: remove direct register accesses outside CM code
+ Linux 3.12-rc4
Signed-off-by: Olof Johansson <olof@lixom.net>
In big endian mode mcpm_entry_point is first function
that called on secondaries CPU. First it should switch
CPU into big endian code.
[ben.dooks@codethink.co.uk: merge fix patch from Victor into this]
Signed-off-by: Victor Kamensky <victor.kamensky@linaro.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Reviewed-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Pull ARM fixes from Russell King:
"Some more ARM fixes, nothing particularly major here. The biggest
change is to fix the SMP_ON_UP code so that it works with TI's Aegis
cores"
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: 7851/1: check for number of arguments in syscall_get/set_arguments()
ARM: 7846/1: Update SMP_ON_UP code to detect A9MPCore with 1 CPU devices
ARM: 7845/1: sharpsl_param.c: fix invalid memory access for pxa devices
ARM: 7843/1: drop asm/types.h from generic-y
ARM: 7842/1: MCPM: don't explode if invoked without being initialized first
This fixes a regression for kernels after v3.2
After commit 72662e0108
ARM: head.S: only include __turn_mmu_on in the initial identity mapping
Zaurus PXA devices call sharpsl_save_param() during fixup and hang on
boot because memcpy refers to physical addresses no longer valid if the
MMU is setup.
Zaurus collie (SA1100) is unaffected (function is called in init_machine).
The code was making assumptions and for PXA the virtual address
should have been used before.
Signed-off-by: Marko Katic <dromede@gmail.com>
Signed-off-by: Andrea Adami <andrea.adami@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Currently mcpm_cpu_power_down() and mcpm_cpu_suspend() trigger BUG()
if mcpm_platform_register() is not called beforehand. This may occur
for many reasons such as some incomplete device tree passed to the kernel
or the like.
Let's be nicer to users and avoid killing the kernel if that happens by
logging a warning and returning to the caller. The mcpm_cpu_suspend()
user is already set to deal with this situation, and so is cpu_die()
invoking mcpm_cpu_die().
The problematic case would have been the B.L switcher's usage of
mcpm_cpu_power_down(), however it has to call mcpm_cpu_power_up() first
which is already set to catch an error resulting from a missing
mcpm_platform_register() call.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
HWMOD removal for MMC is breaking edma_start as the events are being manually
triggered due to unused channel list not being clear.
The above issue is fixed by reading the "dmas" property from the DT node if it
exists and clearing the bits in the unused channel list if the dma controller
used by any device is EDMA. For this purpose we use the of_* helpers to parse
the arguments in the dmas phandle list.
Also introduced is a minor clean up of a checkpatch error in old code.
Reviewed-by: Sekhar Nori <nsekhar@ti.com>
Reported-by: Balaji T K <balajitk@ti.com>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Olof Johansson <olof@lixom.net>
Cc: Nishanth Menon <nm@ti.com>
Cc: Pantel Antoniou <panto@antoniou-consulting.com>
Cc: Jason Kridner <jkridner@beagleboard.org>
Cc: Koen Kooi <koen@dominion.thruhere.net>
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
When the switcher is active, there is no straightforward way to
figure out which logical CPU a given physical CPU maps to.
This patch provides a function
bL_switcher_get_logical_index(mpidr), which is analogous to
get_logical_index().
This function returns the logical CPU on which the specified
physical CPU is grouped (or -EINVAL if unknown).
If the switcher is inactive or not present, -EUNATCH is returned instead.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Signed-off-by: Nicolas Pitre <nico@linaro.org>
This patch exports a bL_switcher_trace_trigger() function to
provide a means for drivers using the trace events to get the
current status when starting a trace session.
Calling this function is equivalent to pinging the trace_trigger
file in sysfs.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
When tracing switching, an external tracer needs a way to bootstrap
its knowledge of the logical<->physical CPU mapping.
This patch adds a sysfs attribute trace_trigger. A write to this
attribute will generate a power:cpu_migrate_current event for each
online CPU, indicating the current physical CPU for each logical
CPU.
Activating or deactivating the switcher also generates these
events, so that the tracer knows about the resulting remapping of
affected CPUs.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
This patch adds simple trace events to the b.L switcher code
to allow tracing of CPU migration events.
To make use of the trace events, you will need:
CONFIG_FTRACE=y
CONFIG_ENABLE_DEFAULT_TRACERS=y
The following events are added:
* power:cpu_migrate_begin
* power:cpu_migrate_finish
each with the following data:
u64 timestamp;
u32 cpu_hwid;
power:cpu_migrate_begin occurs immediately before the
switcher-specific migration operations start.
power:cpu_migrate_finish occurs immediately when migration is
completed.
The cpu_hwid field contains the ID fields of the MPIDR.
* For power:cpu_migrate_begin, cpu_hwid is the ID of the outbound
physical CPU (equivalent to (from_phys_cpu,from_phys_cluster)).
* For power:cpu_migrate_finish, cpu_hwid is the ID of the inbound
physical CPU (equivalent to (to_phys_cpu,to_phys_cluster)).
By design, the cpu_hwid field is masked in the same way as the
device tree cpu node reg property, allowing direct correlation to
the DT description of the hardware.
The timestamp is added in order to minimise timing noise. An
accurate system-wide clock should be used for generating this
(hopefully getnstimeofday is appropriate, but it could be changed).
It could be any monotonic shared clock, since the aim is to allow
accurate deltas to be computed. We don't necessarily care about
accurate synchronisation with wall clock time.
In practice, each switch takes place on a single logical CPU,
and the trace infrastructure should guarantee that events are
well-ordered with respect to a single logical CPU.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Signed-off-by: Nicolas Pitre <nico@linaro.org>
In some cases, a significant delay may be observed between the moment
a request for a CPU to come up is made and the moment it is ready to
start executing kernel code. This is especially true when a whole
cluster has to be powered up which may take in the order of miliseconds.
It is therefore a good idea to let the outbound CPU continue to execute
code in the mean time, and be notified when the inbound is ready before
performing the actual switch.
This is achieved by registering a completion block with the appropriate
IPI callback, and programming the sending of an IPI by the early assembly
code prior to entering the main kernel code. Once the IPI is delivered
to the outbound CPU, the completion block is "completed" and the switcher
thread is resumed.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
This allows to poke a predetermined value into a specific address
upon entering the early boot code in bL_head.S.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Let's wait for the inbound CPU to come up and snoop some of the outbound
CPU cache before bringing the outbound CPU down. That should be more
efficient than going down right away.
Possible improvements might involve some monitoring of the CCI event
counters.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
There is no explicit way to know when a switch started via
bL_switch_request() is complete. This can lead to unpredictable
behaviour when the switcher is controlled by a subsystem which
makes dynamic decisions (such as cpufreq).
The CPU PM notifier is not really suitable for signalling
completion, because the CPU could get suspended and resumed for
other, independent reasons while a switch request is in flight.
Adding a whole new notifier for this seems excessive, and may tempt
people to put heavyweight code on this path.
This patch implements a new bL_switch_request_cb() function that
allows for a per-request lightweight callback, private between the
switcher and the caller of bL_switch_request_cb().
Overlapping switches on a single CPU are considered incorrect if
they are requested via bL_switch_request_cb() with a callback (they
will lead to an unpredictable final state without explicit external
synchronisation to force the requests into a particular order).
Queuing requests robustly would be overkill because only one
subsystem should be attempting to control the switcher at any time.
Overlapping requests of this kind will be failed with -EBUSY to
indicate that the second request won't take effect and the
completer will never be called for it.
bL_switch_request() is retained as a wrapper round the new function,
with the old, fire-and-forget semantics. In this case the last request
will always win. The request may still be denied if a previous request
with a completer is still pending.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Some subsystems will need to respond synchronously to runtime
enabling and disabling of the switcher.
This patch adds a dedicated notifier interface to support such
subsystems. Pre- and post- enable/disable notifications are sent
to registered callbacks, allowing safe transition of non-b.L-
transparent subsystems across these control transitions.
Notifier callbacks may veto switcher (de)activation on pre notifications
only. Post notifications won't revert the action.
If enabling or disabling of the switcher fails after the pre-change
notification has been sent, subsystems which have registered
notifiers can be left in an inappropriate state.
This patch sends a suitable post-change notification on failure,
indicating that the old state has been reestablished.
For example, a failed initialisation will result in the following
sequence:
BL_NOTIFY_PRE_ENABLE
/* switcher initialisation fails */
BL_NOTIFY_POST_DISABLE
It is the responsibility of notified subsystems to respond in an
appropriate way.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Some subsystems will need to know for sure whether the switcher is
enabled or disabled during certain critical regions.
This patch provides a simple mutex-based mechanism to discover
whether the switcher is enabled and temporarily lock out further
enable/disable:
* bL_switcher_get_enabled() returns true iff the switcher is
enabled and temporarily inhibits enable/disable.
* bL_switcher_put_enabled() permits enable/disable of the switcher
again after a previous call to bL_switcher_get_enabled().
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Nicolas Pitre writes:
This is the first part of the patch series adding IKS (In-Kernel
Switcher) support for big.LITTLE system architectures. This consists of
the core patches only. Extra patches to come later will introduce
various optimizations and tracing support.
Those patches were posted on the list a while ago here:
http://news.gmane.org/group/gmane.linux.ports.arm.kernel/thread=253942
The Shark machine sub-architecture (also known as DNARD, the
DIGITAL Network Appliance Reference Design) lacks a maintainer
able to apply and test patches to modernize the architecture.
It is suspected that the current kernel, while it compiles,
does not even boot on this machine. The listed maintainer has
expressed that he will not be able to spend any time on the
maintenance for the coming year.
So let's delete it from the kernel for now. It can always be
resurrected with git revert if maintenance is resumed.
As the VIA82c505 PCI adapter was only used by this
architecture, that gets deleted too.
Cc: arm@kernel.org
Cc: Alexander Schulz <alex@shark-linux.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pull timer code update from Thomas Gleixner:
- armada SoC clocksource overhaul with a trivial merge conflict
- Minor improvements to various SoC clocksource drivers
* 'timers/core' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource: armada-370-xp: Add detailed clock requirements in devicetree binding
clocksource: armada-370-xp: Get reference fixed-clock by name
clocksource: armada-370-xp: Replace WARN_ON with BUG_ON
clocksource: armada-370-xp: Fix device-tree binding
clocksource: armada-370-xp: Introduce new compatibles
clocksource: armada-370-xp: Use CLOCKSOURCE_OF_DECLARE
clocksource: armada-370-xp: Simplify TIMER_CTRL register access
clocksource: armada-370-xp: Use BIT()
ARM: timer-sp: Set dynamic irq affinity
ARM: nomadik: add dynamic irq flag to the timer
clocksource: sh_cmt: 32-bit control register support
clocksource: em_sti: Convert to devm_* managed helpers
Pull slave-dmaengine updates from Vinod Koul:
"This pull brings:
- Andy's DW driver updates
- Guennadi's sh driver updates
- Pl08x driver fixes from Tomasz & Alban
- Improvements to mmp_pdma by Daniel
- TI EDMA fixes by Joel
- New drivers:
- Hisilicon k3dma driver
- Renesas rcar dma driver
- New API for publishing slave driver capablities
- Various fixes across the subsystem by Andy, Jingoo, Sachin etc..."
* 'for-linus' of git://git.infradead.org/users/vkoul/slave-dma: (94 commits)
dma: edma: Remove limits on number of slots
dma: edma: Leave linked to Null slot instead of DUMMY slot
dma: edma: Find missed events and issue them
ARM: edma: Add function to manually trigger an EDMA channel
dma: edma: Write out and handle MAX_NR_SG at a given time
dma: edma: Setup parameters to DMA MAX_NR_SG at a time
dmaengine: pl330: use dma_set_max_seg_size to set the sg limit
dmaengine: dma_slave_caps: remove sg entries
dma: replace devm_request_and_ioremap by devm_ioremap_resource
dma: ste_dma40: Fix potential null pointer dereference
dma: ste_dma40: Remove duplicate const
dma: imx-dma: Remove redundant NULL check
dma: dmagengine: fix function names in comments
dma: add driver for R-Car HPB-DMAC
dma: k3dma: use devm_ioremap_resource() instead of devm_request_and_ioremap()
dma: imx-sdma: Staticize sdma_driver_data structures
pch_dma: Add MODULE_DEVICE_TABLE
dmaengine: PL08x: Add cyclic transfer support
dmaengine: PL08x: Fix reading the byte count in cctl
dmaengine: PL08x: Add support for different maximum transfer size
...
Manual trigger for events missed as a result of splitting a
scatter gather list and DMA'ing it in batches. Add a helper
function to trigger a channel incase any such events are missed.
Signed-off-by: Joel Fernandes <joelf@ti.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When a cpu goes to a deep idle state where its local timer is shutdown, it
notifies the time frame work to use the broadcast timer instead.
Unfortunately, the broadcast device could wake up any CPU, including an idle one
which is not concerned by the wake up at all.
This implies, in the worst case, an idle CPU will wake up to send an IPI to
another idle cpu.
This patch fixes this for ARM platforms using timer-sp, by setting
CLOCK_EVT_FEAT_DYNIRQ feature.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
In a similar manner to our spinlock implementation, mcpm uses sev to
wake up cores waiting on a lock when the lock is unlocked. In order to
ensure that the final write unlocking the lock is visible, a dsb
instruction is executed immediately prior to the sev.
This patch changes these dsbs to use the -st option, since we only
require that the store unlocking the lock is made visible.
Acked-by: Nicolas Pitre <nico@linaro.org>
Reviewed-by: Dave Martin <dave.martin@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Only the basic call to aid debugging.
*** NOT FOR PRODUCTION ***
Usage:
echo <cpuid>,<clusterid> > /dev/b.L_switcher
where <cpuid> is the logical CPU number, and <clusterid> is 0 for the
first cluster and 1 for the second cluster.
Signed-off-by: nicolas Pitre <nico@linaro.org>
Trying to support both the switcher and CPU hotplug at the same time
is tricky due to ambiguous semantics. So let's at least prevent users
from messing around with those logical CPUs the switcher has removed
and those which were not active when the switcher was activated.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Up to now, the logical CPU was somehow tied to the physical CPU number
within a cluster. This causes problems when forcing the boot CPU to be
different from the first enumerated CPU in the device tree creating a
discrepancy between logical and physical CPU numbers.
Let's make the pairing completely independent from physical CPU numbers.
Let's keep only those logical CPUs with same initial CPU cluster to create
a uniform scheduler profile without having to modify any of the probed
topology and compute capacity data. This has the potential to create
a non contiguous CPU numbering space when the switcher is active with
potential impact on buggy user space tools. It is however better to fix
those tools rather than making the switcher code more intrusive.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Reviewed-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
By adding no_bL_switcher to the kernel cmdline string, the switcher
won't be activated automatically at boot time. It is still possible
to activate it later with:
echo 1 > /sys/kernel/bL_switcher/active
Signed-off-by: Nicolas Pitre <nico@linaro.org>
The /sys/kernel/bL_switcher/enable file allows to enable or disable
the switcher by writing 1 or 0 to it respectively. It is still enabled
by default on boot.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Currently, GIC IDs are hardcoded making the code dependent on the 4+4 b.L
configuration. Let's allow for GIC IDs to be discovered upon switcher
initialization to support other b.L configurations such as the 1+1 one,
or 2+3 as on the VExpress TC2.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
In a regular kernel configuration, all the CPUs are initially available.
But the switcher execution model uses half of them at any time. Instead
of hacking the DTB to remove half of the CPUs, let's remove them at
run time and make sure we still have a working switcher configuration.
This way, the same DTB can be used whether or not the switcher is used.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
The workqueues are problematic as they may be contended.
They can't be scheduled with top priority either. Also the optimization
in bL_switch_request() to skip the workqueue entirely when the target CPU
and the calling CPU were the same didn't allow for bL_switch_request() to
be called from atomic context, as might be the case for some cpufreq
drivers.
Let's move to dedicated kthreads instead.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Per-CPU timers that are shutdown when a CPU is switched over must be disabled
upon switching and reprogrammed on the inbound CPU by relying on the
clock events management API. save/restore sequence is executed with irqs
disabled as mandated by the clock events API.
The next_event is an absolute time, hence, when the inbound CPU resumes,
if the timer has expired the min delta is forced into the tick device to
fire after few cycles.
This patch adds switching support for clock events that are per-CPU and
have to be migrated when a switch takes place; the cpumask of the clock
event device is checked against the cpumask of the current cpu, and if
they match, the clockevent device mode is saved and it is put in
shutdown mode. Resume code reprogrammes the tick device accordingly.
Tested on A15/A7 fast models and architected timers.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Nicolas Pitre <nico@linaro.org>
This is the core code implementing big.LITTLE switcher functionality.
Rationale for this code is available here:
http://lwn.net/Articles/481055/
The main entry point for a switch request is:
void bL_switch_request(unsigned int cpu, unsigned int new_cluster_id)
If the calling CPU is not the wanted one, this wrapper takes care of
sending the request to the appropriate CPU with schedule_work_on().
At the moment the core switch operation is handled by bL_switch_to()
which must be called on the CPU for which a switch is requested.
What this code does:
* Return early if the current cluster is the wanted one.
* Close the gate in the kernel entry vector for both the inbound
and outbound CPUs.
* Wake up the inbound CPU so it can perform its reset sequence in
parallel up to the kernel entry vector gate.
* Migrate all interrupts in the GIC targeting the outbound CPU
interface to the inbound CPU interface, including SGIs. This is
performed by gic_migrate_target() in drivers/irqchip/irq-gic.c.
* Call cpu_pm_enter() which takes care of flushing the VFP state to
RAM and save the CPU interface config from the GIC to RAM.
* Modify the cpu_logical_map to refer to the inbound physical CPU.
* Call cpu_suspend() which saves the CPU state (general purpose
registers, page table address) onto the stack and store the
resulting stack pointer in an array indexed by the updated
cpu_logical_map, then call the provided shutdown function.
This happens in arch/arm/kernel/sleep.S.
At this point, the provided shutdown function executed by the outbound
CPU ungates the inbound CPU. Therefore the inbound CPU:
* Picks up the saved stack pointer in the array indexed by its MPIDR
in arch/arm/kernel/sleep.S.
* The MMU and caches are re-enabled using the saved state on the
provided stack, just like if this was a resume operation from a
suspended state.
* Then cpu_suspend() returns, although this is on the inbound CPU
rather than the outbound CPU which called it initially.
* The function cpu_pm_exit() is called which effect is to restore the
CPU interface state in the GIC using the state previously saved by
the outbound CPU.
* Exit of bL_switch_to() to resume normal kernel execution on the
new CPU.
However, the outbound CPU is potentially still running in parallel while
the inbound CPU is resuming normal kernel execution, hence we need
per CPU stack isolation to execute bL_do_switch(). After the outbound
CPU has ungated the inbound CPU, it calls mcpm_cpu_power_down() to:
* Clean its L1 cache.
* If it is the last CPU still alive in its cluster (last man standing),
it also cleans its L2 cache and disables cache snooping from the other
cluster.
* Power down the CPU (or whole cluster).
Code called from bL_do_switch() might end up referencing 'current' for
some reasons. However, 'current' is derived from the stack pointer.
With any arbitrary stack, the returned value for 'current' and any
dereferenced values through it are just random garbage which may lead to
segmentation faults.
The active page table during the execution of bL_do_switch() is also a
problem. There is no guarantee that the inbound CPU won't destroy the
corresponding task which would free the attached page table while the
outbound CPU is still running and relying on it.
To solve both issues, we borrow some of the task space belonging to
the init/idle task which, by its nature, is lightly used and therefore
is unlikely to clash with our usage. The init task is also never going
away.
Right now the logical CPU number is assumed to be equivalent to the
physical CPU number within each cluster. The kernel should also be
booted with only one cluster active. These limitations will be lifted
eventually.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
From Sekhar Nori:
DaVinci fixes for v3.11-rc2
The pull request includes fixes for sparse warnings, defconfig changes to
enable DMA usage on peripherals and removal of a duplicated include file.
* tag 'davinci-fixes-for-v3.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: davinci: defconfig: enable EDMA driver
ARM: davinci: make file local variables static
ARM: edma: remove duplicated include from edma.c
Signed-off-by: Olof Johansson <olof@lixom.net>
The __cpuinit type of throwaway sections might have made sense
some time ago when RAM was more constrained, but now the savings
do not offset the cost and complications. For example, the fix in
commit 5e427ec2d0 ("x86: Fix bit corruption at CPU resume time")
is a good example of the nasty type of bugs that can be created
with improper use of the various __init prefixes.
After a discussion on LKML[1] it was decided that cpuinit should go
the way of devinit and be phased out. Once all the users are gone,
we can then finally remove the macros themselves from linux/init.h.
Note that some harmless section mismatch warnings may result, since
notify_cpu_starting() and cpu_up() are arch independent (kernel/cpu.c)
and are flagged as __cpuinit -- so if we remove the __cpuinit from
the arch specific callers, we will also get section mismatch warnings.
As an intermediate step, we intend to turn the linux/init.h cpuinit
related content into no-ops as early as possible, since that will get
rid of these warnings. In any case, they are temporary and harmless.
This removes all the ARM uses of the __cpuinit macros from C code,
and all __CPUINIT from assembly code. It also had two ".previous"
section statements that were paired off against __CPUINIT
(aka .section ".cpuinit.text") that also get removed here.
[1] https://lkml.org/lkml/2013/5/20/589
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Will Deacon <will.deacon@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Pull timer core updates from Thomas Gleixner:
"The timer changes contain:
- posix timer code consolidation and fixes for odd corner cases
- sched_clock implementation moved from ARM to core code to avoid
duplication by other architectures
- alarm timer updates
- clocksource and clockevents unregistration facilities
- clocksource/events support for new hardware
- precise nanoseconds RTC readout (Xen feature)
- generic support for Xen suspend/resume oddities
- the usual lot of fixes and cleanups all over the place
The parts which touch other areas (ARM/XEN) have been coordinated with
the relevant maintainers. Though this results in an handful of
trivial to solve merge conflicts, which we preferred over nasty cross
tree merge dependencies.
The patches which have been committed in the last few days are bug
fixes plus the posix timer lot. The latter was in akpms queue and
next for quite some time; they just got forgotten and Frederic
collected them last minute."
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (59 commits)
hrtimer: Remove unused variable
hrtimers: Move SMP function call to thread context
clocksource: Reselect clocksource when watchdog validated high-res capability
posix-cpu-timers: don't account cpu timer after stopped thread runtime accounting
posix_timers: fix racy timer delta caching on task exit
posix-timers: correctly get dying task time sample in posix_cpu_timer_schedule()
selftests: add basic posix timers selftests
posix_cpu_timers: consolidate expired timers check
posix_cpu_timers: consolidate timer list cleanups
posix_cpu_timer: consolidate expiry time type
tick: Sanitize broadcast control logic
tick: Prevent uncontrolled switch to oneshot mode
tick: Make oneshot broadcast robust vs. CPU offlining
x86: xen: Sync the CMOS RTC as well as the Xen wallclock
x86: xen: Sync the wallclock when the system time is set
timekeeping: Indicate that clock was set in the pvclock gtod notifier
timekeeping: Pass flags instead of multiple bools to timekeeping_update()
xen: Remove clock_was_set() call in the resume path
hrtimers: Support resuming with two or more CPUs online (but stopped)
timer: Fix jiffies wrap behavior of round_jiffies_common()
...
Pull ARM updates from Russell King:
"This contains the usual updates from other people (listed below) and
the usual random muddle of miscellaneous ARM updates which cover some
low priority bug fixes and performance improvements.
I've started to put the pull request wording into the merge commits,
which are:
- NoMMU stuff:
This includes the following series sent earlier to the list:
- nommu-fixes
- R7 Support
- MPU support
I've left out the ARCH_MULTIPLATFORM/!MMU stuff that Arnd and I
were discussing today until we've reached a conclusion/that's had
some more review.
This is rebased (and re-tested) on your devel-stable branch because
otherwise there were going to be conflicts with Uwe's V7M work now
that you've merged that. I've included the fix for limiting MPU to
CPU_V7.
- Huge page support
These changes bring both HugeTLB support and Transparent HugePage
(THP) support to ARM. Only long descriptors (LPAE) are supported
in this series.
The code has been tested on an Arndale board (Exynos 5250).
- LPAE updates
Please pull these miscellaneous LPAE fixes I've been collecting for
a while now for 3.11. They've been tested and reviewed by quite a
few people, and most of the patches are pretty trivial. -- Will Deacon.
- arch_timer cleanups
Please pull these arch_timer cleanups I've been holding onto for a
while. They're the same as my last posting, but have been rebased
to v3.10-rc3.
- mpidr linearisation (multiprocessor id register - identifies which
CPU number we are in the system)
This patch series that implements MPIDR linearization through a
simple hashing algorithm and updates current cpu_{suspend}/{resume}
code to use the newly created hash structures to retrieve context
pointers. It represents a stepping stone for the implementation of
power management code on forthcoming multi-cluster ARM systems.
It has been tested on TC2 (dual cluster A15xA7 system), iMX6q,
OMAP4 and Tegra, with processors hitting low-power states requiring
warm-boot resume through the cpu_resume code path"
* 'for-linus' of git://git.linaro.org/people/rmk/linux-arm: (77 commits)
ARM: 7775/1: mm: Remove do_sect_fault from LPAE code
ARM: 7777/1: Avoid extra calls to the C compiler
ARM: 7774/1: Fix dtb dependency to use order-only prerequisites
ARM: 7770/1: remove residual ARMv2 support from decompressor
ARM: 7769/1: Cortex-A15: fix erratum 798181 implementation
ARM: 7768/1: prevent risks of out-of-bound access in ASID allocator
ARM: 7767/1: let the ASID allocator handle suspended animation
ARM: 7766/1: versatile: don't mark pen as __INIT
ARM: 7765/1: perf: Record the user-mode PC in the call chain.
ARM: 7735/2: Preserve the user r/w register TPIDRURW on context switch and fork
ARM: kernel: implement stack pointer save array through MPIDR hashing
ARM: kernel: build MPIDR hash function data structure
ARM: mpu: Ensure that MPU depends on CPU_V7
ARM: mpu: protect the vectors page with an MPU region
ARM: mpu: Allow enabling of the MPU via kconfig
ARM: 7758/1: introduce config HAS_BANDGAP
ARM: 7757/1: mm: don't flush icache in switch_mm with hardware broadcasting
ARM: 7751/1: zImage: don't overwrite ourself with a page table
ARM: 7749/1: spinlock: retry trylock operation if strex fails on free lock
ARM: 7748/1: oabi: handle faults when loading swi instruction from userspace
...
EDMA supports a cross bar which provides ability
to mux additional events into physical channels
present in the channel controller.
This is required when the number of events present
in the system are more than number of available
physical channels.
Changes by Joel:
* Split EDMA xbar support out of original EDMA DT parsing patch
to keep it easier for review.
* Rewrite shift and offset calculation.
Suggested-by: Sekhar Nori <nsekhar@ti.com>
Suggested by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Joel A Fernandes <joelagnel@ti.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
[nsekhar@ti.com: fix checkpatch errors and a minor coding improvement]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Adds support for parsing the TI EDMA DT data into the required EDMA
private API platform data. Enables runtime PM support to initialize
the EDMA hwmod. Enables build on OMAP.
Changes by Joel:
* Setup default one-to-one mapping for queue_priority and queue_tc
mapping as discussed in [1].
* Split out xbar stuff to separate patch. [1]
* Dropped unused DT helper to convert to array
* Fixed dangling pointer issue with Sekhar's changes
[1] https://patchwork.kernel.org/patch/2226761/
Signed-off-by: Matt Porter <mporter@ti.com>
[nsekhar@ti.com: fix checkpatch errors, build breakages. Introduce
edma_setup_info_from_dt() as part of that effort]
Signed-off-by: Joel A Fernandes <joelagnel@ti.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Use devm_ioremap_resource instead of reques_mem_region()/ioremap(),
devm_request_irq() instead of request_irq() and kzalloc() calls to
devm_kzalloc().
This ensures more consistent error values and simplifies error paths.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
[nsekhar@ti.com: add missing err.h include]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Fix build on OMAP, the irqs are undefined on AM33xx.
These error interrupt handlers were hardcoded as disabled
so since they are unused code, simply remove them.
Signed-off-by: Matt Porter <mporter@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Move mach-davinci/dma.c to common/edma.c so it can be used
by OMAP (specifically AM33xx) as well.
Signed-off-by: Matt Porter <mporter@ti.com>
Acked-by: Chris Ball <cjb@laptop.org> # davinci_mmc.c
Acked-by: Mark Brown <broonie@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
[nsekhar@ti.com: dropped davinci sffsdr changes]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Nothing about the sched_clock implementation in the ARM port is
specific to the architecture. Generalize the code so that other
architectures can use it by selecting GENERIC_SCHED_CLOCK.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
[jstultz: Merge minor collisions with other patches in my tree]
Signed-off-by: John Stultz <john.stultz@linaro.org>
The smp_init_cpus method in the smp_operations structure is optional
and can be omitted entirely.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The CPU and cluster numbers (MPIDR affinity levels 0 and 1) may have
at most 8 bits each.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Pull ARM fixes from Russell King:
"A small number of fixes for stuff from the last merge window, and in
one case (IRQ time accounting) the previous merge window."
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: 7720/1: ARM v6/v7 cmpxchg64 shouldn't clear upper 32 bits of the old/new value
ARM: 7715/1: MCPM: adapt to GIC changes after upstream merge
ARM: 7714/1: mmc: mmci: Ensure return value of regulator_enable() is checked
ARM: 7712/1: Remove trailing whitespace in arch/arm/Makefile
ARM: 7711/1: dove: fix Dove cpu type from V7 to PJ4
ARM: finally enable IRQ time accounting config
Since commit c0114709ed ("irqchip: gic: Perform the gic_secondary_init()
call via CPU notifier") it is no longer required nor possible to call
gic_secondary_init() from platform code.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
These are cleanups and smaller changes that either depend on earlier
feature branches or came in late during the development cycle.
We normally try to get all cleanups early, so these are the exceptions:
- A follow-up on the clocksource reworks, hopefully the last time
we need to merge clocksource subsystem changes through arm-soc.
A first set of patches was part of the original 3.10 arm-soc cleanup
series because of interdependencies with timer drivers now moved out
of arch/arm.
- Migrating the SPEAr13xx platform away from using auxdata for DMA
channel descriptions towards using information in device tree,
based on the earlier SPEAr multiplatform series
- A few follow-ups on the Atmel SAMA5 support and other changes
for Atmel at91 based on the larger at91 reworks.
- Moving the armada irqchip implementation to drivers/irqchip
- Several OMAP cleanups following up on the larger series already
merged in 3.10.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=HWfp
-----END PGP SIGNATURE-----
Merge tag 'cleanup-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC late cleanups from Arnd Bergmann:
"These are cleanups and smaller changes that either depend on earlier
feature branches or came in late during the development cycle. We
normally try to get all cleanups early, so these are the exceptions:
- A follow-up on the clocksource reworks, hopefully the last time we
need to merge clocksource subsystem changes through arm-soc.
A first set of patches was part of the original 3.10 arm-soc
cleanup series because of interdependencies with timer drivers now
moved out of arch/arm.
- Migrating the SPEAr13xx platform away from using auxdata for DMA
channel descriptions towards using information in device tree,
based on the earlier SPEAr multiplatform series
- A few follow-ups on the Atmel SAMA5 support and other changes for
Atmel at91 based on the larger at91 reworks.
- Moving the armada irqchip implementation to drivers/irqchip
- Several OMAP cleanups following up on the larger series already
merged in 3.10."
* tag 'cleanup-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (50 commits)
ARM: OMAP4: change the device names in usb_bind_phy
ARM: OMAP2+: Fix mismerge for timer.c between ff931c82 and da4a686a
ARM: SPEAr: conditionalize SMP code
ARM: arch_timer: Silence debug preempt warnings
ARM: OMAP: remove unused variable
serial: amba-pl011: fix !CONFIG_DMA_ENGINE case
ata: arasan: remove the need for platform_data
ARM: at91/sama5d34ek.dts: remove not needed compatibility string
ARM: at91: dts: add MCI DMA support
ARM: at91: dts: add i2c dma support
ARM: at91: dts: set #dma-cells to the correct value
ARM: at91: suspend both memory controllers on at91sam9263
irqchip: armada-370-xp: slightly cleanup irq controller driver
irqchip: armada-370-xp: move IRQ handler to avoid forward declaration
irqchip: move IRQ driver for Armada 370/XP
ARM: mvebu: move L2 cache initialization in init_early()
devtree: add binding documentation for sp804
ARM: integrator-cp: convert use CLKSRC_OF for timer init
ARM: versatile: use OF init for sp804 timer
ARM: versatile: add versatile dtbs to dtbs target
...
Two platforms, bcm and exynos have their own firmware interfaces using
the "secure monitor call", this adds support for those.
We had originally planned to have a third set of patches in here, which
would extend support for the existing generic "psci" call that is used
on multiple platforms as well as Xen and KVM guests, but that ended up
getting dropped because the patches were not ready in time.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=68m5
-----END PGP SIGNATURE-----
Merge tag 'firmware-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM platform specific firmware interfaces from Olof Johansson:
"Two platforms, bcm and exynos have their own firmware interfaces using
the "secure monitor call", this adds support for those.
We had originally planned to have a third set of patches in here,
which would extend support for the existing generic "psci" call that
is used on multiple platforms as well as Xen and KVM guests, but that
ended up getting dropped because the patches were not ready in time."
* tag 'firmware-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: bcm: mark bcm_kona_smc_init as __init
ARM: bcm281xx: Add DT support for SMC handler
ARM: bcm281xx: Add L2 cache enable code
ARM: EXYNOS: Add secure firmware support to secondary CPU bring-up
ARM: EXYNOS: Add IO mapping for non-secure SYSRAM.
ARM: EXYNOS: Add support for Exynos secure firmware
ARM: EXYNOS: Add support for secure monitor calls
ARM: Add interface for registering and calling firmware-specific operations
The full mcpm layer is not likely to be relevant to v6 based
platforms, so a multiplatform kernel won't use that code if booted
on v6 hardware.
This patch modifies the AFLAGS for affected mcpm .S files to
specify armv7-a explicitly for that code.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Now that the cluster power API is in place, we can use it for SMP secondary
bringup and CPU hotplug in a generic fashion.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Will Deacon <will.deacon@arm.com>
Instead of requiring the first man to be elected in advance (which
can be suboptimal in some situations), this patch uses a per-
cluster mutex to co-ordinate selection of the first man.
This should also make it more feasible to reuse this code path for
asynchronous cluster resume (as in CPUidle scenarios).
We must ensure that the vlock data doesn't share a cacheline with
anything else, or dirty cache eviction could corrupt it.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Will Deacon <will.deacon@arm.com>
This patch adds a simple low-level voting mutex implementation
to be used to arbitrate during first man selection when no load/store
exclusive instructions are usable.
For want of a better name, these are called "vlocks". (I was
tempted to call them ballot locks, but "block" is way too confusing
an abbreviation...)
There is no function to wait for the lock to be released, and no
vlock_lock() function since we don't need these at the moment.
These could straightforwardly be added if vlocks get used for other
purposes.
For architectural correctness even Strongly-Ordered memory accesses
require barriers in order to guarantee that multiple CPUs have a
coherent view of the ordering of memory accesses. Whether or not
this matters depends on hardware implementation details of the
memory system. Since the purpose of this code is to provide a clean,
generic locking mechanism with no platform-specific dependencies the
barriers should be present to avoid unpleasant surprises on future
platforms.
Note:
* When taking the lock, we don't care about implicit background
memory operations and other signalling which may be pending,
because those are not part of the critical section anyway.
A DMB is sufficient to ensure correctly observed ordering if
the explicit memory accesses in vlock_trylock.
* No barrier is required after checking the election result,
because the result is determined by the store to
VLOCK_OWNER_OFFSET and is already globally observed due to the
barriers in voting_end. This means that global agreement on
the winner is guaranteed, even before the winner is known
locally.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Will Deacon <will.deacon@arm.com>
This provides helper methods to coordinate between CPUs coming down
and CPUs going up, as well as documentation on the used algorithms,
so that cluster teardown and setup
operations are not done for a cluster simultaneously.
For use in the power_down() implementation:
* __mcpm_cpu_going_down(unsigned int cluster, unsigned int cpu)
* __mcpm_outbound_enter_critical(unsigned int cluster)
* __mcpm_outbound_leave_critical(unsigned int cluster)
* __mcpm_cpu_down(unsigned int cluster, unsigned int cpu)
The power_up_setup() helper should do platform-specific setup in
preparation for turning the CPU on, such as invalidating local caches
or entering coherency. It must be assembler for now, since it must
run before the MMU can be switched on. It is passed the affinity level
for which initialization should be performed.
Because the mcpm_sync_struct content is looked-up and modified
with the cache enabled or disabled depending on the code path, it is
crucial to always ensure proper cache maintenance to update main memory
right away. The sync_cache_*() helpers are used to that end.
Also, in order to prevent a cached writer from interfering with an
adjacent non-cached writer, we ensure each state variable is located to
a separate cache line.
Thanks to Nicolas Pitre and Achin Gupta for the help with this
patch.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Reviewed-by: Will Deacon <will.deacon@arm.com>
This is the basic API used to handle the powering up/down of individual
CPUs in a (multi-)cluster system. The platform specific backend
implementation has the responsibility to also handle the cluster level
power as well when the first/last CPU in a cluster is brought up/down.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Will Deacon <will.deacon@arm.com>
CPUs in cluster based systems, such as big.LITTLE, have special needs
when entering the kernel due to a hotplug event, or when resuming from
a deep sleep mode.
This is vectorized so multiple CPUs can enter the kernel in parallel
without serialization.
The mcpm prefix stands for "multi cluster power management", however
this is usable on single cluster systems as well. Only the basic
structure is introduced here. This will be extended with later patches.
In order not to complexify things more than they currently have to,
the planned work to make runtime adjusted MPIDR based indexing and
dynamic memory allocation for cluster states is postponed to a later
cycle. The MAX_NR_CLUSTERS and MAX_CPUS_PER_CLUSTER static definitions
should be sufficient for those systems expected to be available in the
near future.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Will Deacon <will.deacon@arm.com>
Move the integrator-cp timer init to timer-sp.c and use CLKSRC_OF. There is
no reason to use the aliases, so drop them from the init code.
The integrator-cp timers are mistakenly called sp804 timers in the dts, but
in fact they are not sp804 dual timers, but single timers with the same
programming model. Fix the dts to reflect this.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
This adds CLKSRC_OF based init for sp804 timer. The clock initialization is
refactored to support retrieving the clock(s) from the DT.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Some boards are running with secure firmware running in TrustZone secure
world, which changes the way some things have to be initialized.
This patch adds an interface for platforms to specify available firmware
operations and call them.
A wrapper macro, call_firmware_op(), checks if the operation is provided
and calls it if so, otherwise returns -ENOSYS to allow fallback to
legacy operation..
By default no operations are provided.
Example of use:
In code using firmware ops:
__raw_writel(virt_to_phys(exynos4_secondary_startup),
CPU1_BOOT_REG);
/* Call Exynos specific smc call */
if (call_firmware_op(cpu_boot, cpu) == -ENOSYS)
cpu_boot_legacy(...); /* Try legacy way */
gic_raise_softirq(cpumask_of(cpu), 1);
In board-/platform-specific code:
static int platformX_do_idle(void)
{
/* tell platformX firmware to enter idle */
return 0;
}
static int platformX_cpu_boot(int i)
{
/* tell platformX firmware to boot CPU i */
return 0;
}
static const struct firmware_ops platformX_firmware_ops = {
.do_idle = exynos_do_idle,
.cpu_boot = exynos_cpu_boot,
/* other operations not available on platformX */
};
static void __init board_init_early(void)
{
register_firmware_ops(&platformX_firmware_ops);
}
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Now that we have drivers/irqchip, move VIC irqchip to drivers/irqchip.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Now that the VIC initialization sets up the handle_arch_irq pointer, we
can remove it for all machines and make it static. Move vic_handle_irq
to avoid a forward declaration.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Ryan Mallon <rmallon@gmail.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Hubert Feurstein <hubert.feurstein@contec.at>
Cc: Alessandro Rubini <rubini@unipv.it>
Cc: STEricsson <STEricsson_nomadik_linux@list.st.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Shiraz Hashim <shiraz.hashim@st.com>
Cc: Rajeev Kumar <rajeev-dlh.kumar@st.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Set handle_arch_irq to vic_handle_irq. Only the first VIC initialized can
setup the handler.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Olof Johansson <olof@lixom.net>
Move all register defines except VIC_INT_ENABLE and VIC_INT_ENABLE_CLEAR
which are used by Samsung.
With multi irq handler, vic.h is not included in assembly any more, so
we can remove the assembly ifdefs.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Russell King <linux@arm.linux.org.uk>
Acked-by: Olof Johansson <olof@lixom.net>
Now that we have drivers/irqchip, move GIC irqchip to drivers/irqchip. This
is necessary to share the GIC with arm and arm64.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Now that the GIC initialization sets up the handle_arch_irq pointer, we
can remove it for all machines and make it static.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Anton Vorontsov <avorontsov@mvista.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: David Brown <davidb@codeaurora.org>
Cc: Daniel Walker <dwalker@fifo99.com>
Cc: Bryan Huntsman <bryanh@codeaurora.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Magnus Damm <magnus.damm@gmail.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Shiraz Hashim <shiraz.hashim@st.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Set handle_arch_irq to gic_handle_irq. Only the first GIC initialized can
setup the handler.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Olof Johansson <olof@lixom.net>
In preparation of moving gic code to drivers/irqchip, remove the direct
platform dependencies on gic_raise_softirq. Move the setup of
smp_cross_call into the gic code and use arch_send_wakeup_ipi_mask
function to trigger wake-up IPIs.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: David Brown <davidb@codeaurora.org>
Cc: Daniel Walker <dwalker@fifo99.com>
Cc: Bryan Huntsman <bryanh@codeaurora.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Magnus Damm <magnus.damm@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Shiraz Hashim <shiraz.hashim@st.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Pull ARM fixes from Russell King.
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: 7616/1: cache-l2x0: aurora: Use writel_relaxed instead of writel
ARM: 7615/1: cache-l2x0: aurora: Invalidate during clean operation with WT enable
ARM: 7614/1: mm: fix wrong branch from Cortex-A9 to PJ4b
ARM: 7612/1: imx: Do not select some errata that depends on !ARCH_MULTIPLATFORM
ARM: 7611/1: VIC: fix bug in VIC irqdomain code
ARM: 7610/1: versatile: bump IRQ numbers
ARM: 7609/1: disable errata work-arounds which access secure registers
ARM: 7608/1: l2x0: Only set .set_debug on PL310 r3p0 and earlier
CONFIG_HOTPLUG is going away as an option. As a result, the __dev*
markings need to be removed.
This change removes the use of __devinit, __devexit_p, __devinitdata,
and __devexit from these drivers.
Based on patches originally written by Bill Pemberton, but redone by me
in order to handle some of the coding style issues better, by hand.
Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The VIC irqdomain code added in commit
07c9249f1f
"ARM: 7554/1: VIC: use irq_domain_add_simple()"
Had two bugs:
1) It didn't call irq_create_mapping() once on each
valid irq source in the slowpath when registering
the controller.
2) It passed a -1 as IRQ offset for the DT case, whereas
0 should be passed as invalid IRQ instead.
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The SP804 driver statically initialises the cpumask of the clock event
device to be cpu_all_mask, which is derived from the compile-time
constant NR_CPUS. This breaks SMP_ON_UP systems where the interrupt
controller handling the sp804 doesn't have the irq_set_affinity callback
on the irq_chip, because the common timer code fails to identify the
device as cpu-local and ends up treating it as a broadcast device
instead.
This patch fixes the problem by using cpu_possible_mask at runtime,
which will correctly represent the possible CPUs when SMP_ON_UP is being
used.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The GIC interface numbering does not necessarily follow the logical
CPU numbering, especially for complex topologies such as multi-cluster
systems.
Fortunately we can easily probe the GIC to create a mapping as the
Interrupt Processor Targets Registers for the first 32 interrupts are
read-only, and each field returns a value that always corresponds to
the processor reading the register.
Initially all mappings target all CPUs in case an IPI is required to
boot secondary CPUs. It is refined as those CPUs discover what their
actual mapping is.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Will Deacon <will.deacon@arm.com>
07c9249f1f (ARM: 7554/1: VIC: use irq_domain_add_simple()) removed the
use of 'irq_base' but did not remove the variable itself, which causes:
arch/arm/common/vic.c: In function 'vic_of_init':
arch/arm/common/vic.c:410:6: warning: unused variable 'irq_base'
Remove this now unused variable.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Instead of allocating descriptors on-the-fly for the device tree
initialization case, use irq_domain_add_simple() which will take
care of this if you pass negative as the first_irq.
Alter the signature of __vic_init() to pass the first_irq as
signed so this works as expected.
Switching the VIC to use irq_domain_add_simple() also has the
upside of displaying the same WARNING when you boot with
pre-allocated descriptors on systems using SPARSE_IRQ but
yet not using device tree.
Cc: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As suggested by Andrew Morton:
This is a pet peeve of mine. Any time there's a long list of items
(header file inclusions, kconfig entries, array initalisers, etc) and
someone wants to add a new item, they *always* go and stick it at the
end of the list.
Guys, don't do this. Either put the new item into a randomly-chosen
position or, probably better, alphanumerically sort the list.
lets sort all our select statements alphanumerically. This commit was
created by the following perl:
while (<>) {
while (/\\\s*$/) {
$_ .= <>;
}
undef %selects if /^\s*config\s+/;
if (/^\s+select\s+(\w+).*/) {
if (defined($selects{$1})) {
if ($selects{$1} eq $_) {
print STDERR "Warning: removing duplicated $1 entry\n";
} else {
print STDERR "Error: $1 differently selected\n".
"\tOld: $selects{$1}\n".
"\tNew: $_\n";
exit 1;
}
}
$selects{$1} = $_;
next;
}
if (%selects and (/^\s*$/ or /^\s+help/ or /^\s+---help---/ or
/^endif/ or /^endchoice/)) {
foreach $k (sort (keys %selects)) {
print "$selects{$k}";
}
undef %selects;
}
print;
}
if (%selects) {
foreach $k (sort (keys %selects)) {
print "$selects{$k}";
}
}
It found two duplicates:
Warning: removing duplicated S5P_SETUP_MIPIPHY entry
Warning: removing duplicated HARDIRQS_SW_RESEND entry
and they are identical duplicates, hence the shrinkage in the diffstat
of two lines.
We have four testers reporting success of this change (Tony, Stephen,
Linus and Sekhar.)
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The it8152 PCI host used on the pxa/cm_x2xx machines
uses the old-style I/O window registration. This should
eventually get converted to pci_ioremap_io() but for
now, let's cast the IT8152_IO_BASE constant to an integer
type to get rid of the warnings.
Without this patch, building cm_x2xx_defconfig results in:
arch/arm/common/it8152.c: In function 'it8152_pci_setup':
arch/arm/common/it8152.c:287:18: warning: assignment makes integer from pointer without a cast [enabled by default]
arch/arm/common/it8152.c:288:16: warning: assignment makes integer from pointer without a cast [enabled by default]
arch/arm/common/it8152.c:291:17: warning: assignment makes integer from pointer without a cast [enabled by default]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Krzysztof Halasa <khc@pm.waw.pl>
Cc: Mike Rapoport <mike@compulab.co.il>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Eric Miao <eric.y.miao@gmail.com>
This patch adds support for dma_get_sgtable() function which is required
to let drivers to share the buffers allocated by DMA-mapping subsystem.
Generic implementation based on virt_to_page() is not suitable for ARM
dma-mapping subsystem.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Kyungmin Park <kyungmin.park@samsung.com>
This patch fixes the usage of uninitialized variables in dmabounce code
intoduced by commit a227fb92 ('ARM: dma-mapping: remove offset parameter
to prepare for generic dma_ops'):
arch/arm/common/dmabounce.c: In function ‘dmabounce_sync_for_device’:
arch/arm/common/dmabounce.c:409: warning: ‘off’ may be used uninitialized in this function
arch/arm/common/dmabounce.c:407: note: ‘off’ was declared here
arch/arm/common/dmabounce.c: In function ‘dmabounce_sync_for_cpu’:
arch/arm/common/dmabounce.c:369: warning: ‘off’ may be used uninitialized in this function
arch/arm/common/dmabounce.c:367: note: ‘off’ was declared here
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Pull CMA and ARM DMA-mapping updates from Marek Szyprowski:
"These patches contain two major updates for DMA mapping subsystem
(mainly for ARM architecture). First one is Contiguous Memory
Allocator (CMA) which makes it possible for device drivers to allocate
big contiguous chunks of memory after the system has booted.
The main difference from the similar frameworks is the fact that CMA
allows to transparently reuse the memory region reserved for the big
chunk allocation as a system memory, so no memory is wasted when no
big chunk is allocated. Once the alloc request is issued, the
framework migrates system pages to create space for the required big
chunk of physically contiguous memory.
For more information one can refer to nice LWN articles:
- 'A reworked contiguous memory allocator':
http://lwn.net/Articles/447405/
- 'CMA and ARM':
http://lwn.net/Articles/450286/
- 'A deep dive into CMA':
http://lwn.net/Articles/486301/
- and the following thread with the patches and links to all previous
versions:
https://lkml.org/lkml/2012/4/3/204
The main client for this new framework is ARM DMA-mapping subsystem.
The second part provides a complete redesign in ARM DMA-mapping
subsystem. The core implementation has been changed to use common
struct dma_map_ops based infrastructure with the recent updates for
new dma attributes merged in v3.4-rc2. This allows to use more than
one implementation of dma-mapping calls and change/select them on the
struct device basis. The first client of this new infractructure is
dmabounce implementation which has been completely cut out of the
core, common code.
The last patch of this redesign update introduces a new, experimental
implementation of dma-mapping calls on top of generic IOMMU framework.
This lets ARM sub-platform to transparently use IOMMU for DMA-mapping
calls if one provides required IOMMU hardware.
For more information please refer to the following thread:
http://www.spinics.net/lists/arm-kernel/msg175729.html
The last patch merges changes from both updates and provides a
resolution for the conflicts which cannot be avoided when patches have
been applied on the same files (mainly arch/arm/mm/dma-mapping.c)."
Acked by Andrew Morton <akpm@linux-foundation.org>:
"Yup, this one please. It's had much work, plenty of review and I
think even Russell is happy with it."
* 'for-linus' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping: (28 commits)
ARM: dma-mapping: use PMD size for section unmap
cma: fix migration mode
ARM: integrate CMA with DMA-mapping subsystem
X86: integrate CMA with DMA-mapping subsystem
drivers: add Contiguous Memory Allocator
mm: trigger page reclaim in alloc_contig_range() to stabilise watermarks
mm: extract reclaim code from __alloc_pages_direct_reclaim()
mm: Serialize access to min_free_kbytes
mm: page_isolation: MIGRATE_CMA isolation functions added
mm: mmzone: MIGRATE_CMA migration type added
mm: page_alloc: change fallbacks array handling
mm: page_alloc: introduce alloc_contig_range()
mm: compaction: export some of the functions
mm: compaction: introduce isolate_freepages_range()
mm: compaction: introduce map_pages()
mm: compaction: introduce isolate_migratepages_range()
mm: page_alloc: remove trailing whitespace
ARM: dma-mapping: add support for IOMMU mapper
ARM: dma-mapping: use alloc, mmap, free from dma_ops
ARM: dma-mapping: remove redundant code and do the cleanup
...
Conflicts:
arch/x86/include/asm/dma-mapping.h
These cleanups are basically all over the place. The idea is to collect
changes with minimal impact but large number of changes so we can avoid
them from distracting in the diffstat in the other series.
A significant number of lines get removed here, in particular because
the ixp2000 and ixp23xx platforms get removed. These have never been
extremely popular and have fallen into disuse over time with no active
maintainer taking care of them. The u5500 soc never made it into a
product, so we are removing it from the ux500 platform.
Many good cleanups also went into the at91 and omap platforms, as has
been the case for a number of releases.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Hcjs
-----END PGP SIGNATURE-----
Merge tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull first batch of arm-soc cleanups from Olof Johansson:
"These cleanups are basically all over the place. The idea is to
collect changes with minimal impact but large number of changes so we
can avoid them from distracting in the diffstat in the other series.
A significant number of lines get removed here, in particular because
the ixp2000 and ixp23xx platforms get removed. These have never been
extremely popular and have fallen into disuse over time with no active
maintainer taking care of them. The u5500 soc never made it into a
product, so we are removing it from the ux500 platform.
Many good cleanups also went into the at91 and omap platforms, as has
been the case for a number of releases."
Trivial modify-delete conflicts in arch/arm/mach-{ixp2000,ixp23xx}
* tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (152 commits)
ARM: clps711x: Cleanup IRQ handling
ARM clps711x: Removed unused header mach/time.h
ARM: clps711x: Added note about support EP731x CPU to Kconfig
ARM: clps711x: Added missing register definitions
ARM: clps711x: Used own subarch directory for store header file
Dove: Fix Section mismatch warnings
ARM: orion5x: ts78xx debugging changes
ARM: orion5x: remove PM dependency from ts78xx
ARM: orion5x: ts78xx fix NAND resource off by one
ARM: orion5x: ts78xx whitespace cleanups
Orion5x: Fix Section mismatch warnings
Orion5x: Fix warning: struct pci_dev declared inside paramter list
ARM: clps711x: Combine header files into one for clps711x-targets
ARM: S3C24XX: Use common macro to define resources on mach-qt2410.c
ARM: S3C24XX: Use common macro to define resources on mach-osiris.c
ARM: EXYNOS: Adapt to cpuidle core time keeping and irq enable
ARM: S5PV210: Use common macro to define resources on mach-smdkv210.c
ARM: S5PV210: Use common macro to define resources on dev-audio.c
ARM: S5PC100: Use common macro to define resources on dev-audio.c
ARM: S5P64X0: Use common macro to define resources on dev-audio.c
...
This patch converts dma_alloc/free/mmap_{coherent,writecombine}
functions to use generic alloc/free/mmap methods from dma_map_ops
structure. A new DMA_ATTR_WRITE_COMBINE DMA attribute have been
introduced to implement writecombine methods.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Tested-By: Subash Patel <subash.ramaswamy@linaro.org>
This patch removes dma bounce hooks from the common dma mapping
implementation on ARM architecture and creates a separate set of
dma_map_ops for dma bounce devices.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-By: Subash Patel <subash.ramaswamy@linaro.org>
This patch removes the need for the offset parameter in dma bounce
functions. This is required to let dma-mapping framework on ARM
architecture to use common, generic dma_map_ops based dma-mapping
helpers.
Background and more detailed explaination:
dma_*_range_* functions are available from the early days of the dma
mapping api. They are the correct way of doing a partial syncs on the
buffer (usually used by the network device drivers). This patch changes
only the internal implementation of the dma bounce functions to let
them tunnel through dma_map_ops structure. The driver api stays
unchanged, so driver are obliged to call dma_*_range_* functions to
keep code clean and easy to understand.
The only drawback from this patch is reduced detection of the dma api
abuse. Let us consider the following code:
dma_addr = dma_map_single(dev, ptr, 64, DMA_TO_DEVICE);
dma_sync_single_range_for_cpu(dev, dma_addr+16, 0, 32, DMA_TO_DEVICE);
Without the patch such code fails, because dma bounce code is unable
to find the bounce buffer for the given dma_address. After the patch
the above sync call will be equivalent to:
dma_sync_single_range_for_cpu(dev, dma_addr, 16, 32, DMA_TO_DEVICE);
which succeeds.
I don't consider this as a real problem, because DMA API abuse should be
caught by debug_dma_* function family. This patch lets us to simplify
the internal low-level implementation without chaning the driver visible
API.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-By: Subash Patel <subash.ramaswamy@linaro.org>
Replace all uses of ~0 with DMA_ERROR_CODE, what should make the code
easier to read.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-By: Subash Patel <subash.ramaswamy@linaro.org>
Most PCI implementations perform simple root bus scanning. Rather than
having each group of platforms provide a duplicated bus scan function,
provide the PCI configuration ops structure via the hw_pci structure,
and call the root bus scanning function from core ARM PCI code.
Acked-by: Krzysztof Hałasa <khc@pm.waw.pl>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This removes the internal functions for assigning IRQ
handlers to each interrupt in favor of using the internal
map iterator in the irq domain code.
Cc: Will Deacon <will.deacon@arm.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Acked-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The current IRQ domain implementation in the VIC allocates 32
interrupts for each VIC instance no matter whether the
controller actually use all the IRQs or not. Alter this so
we only allocate a domain up until the last IRQ marked valid.
Cc: Will Deacon <will.deacon@arm.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Acked-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
- The biggest improvement of this series is the ability to compile several
AT91 SoCs in one kernel image.
For now on it's limited to the DT-enabled boards but we can compile all
the core together.
- The Kconfig series is stacked before other patches as it is simple and
non-intrusive. Its goal is to remove too restrictive dependencies on
SoC names. This will allow to add support for newer SoC seamlessly.
- Some very "cosmetic" Kconfig changes are also added (entry names,
comments, etc.).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJPjYz4AAoJEAf03oE53VmQ/0wH/3kXJYM/8nX8fqlQ8eTh0SHi
lRsoNL+4arHFKcocYhZyiXEidUKCUMLuQSdvL9MWy1e286+ABsaFgrjfLsp/ZDqE
jDJBCZIxUD6rL94VRnYEHrhWqGzzPKi8/syVZ8JOv/1HGml402CqPcRDKmWY/e4Q
ajl/d463q0ufwfQ4LMP+DsR29TxEdecs4DkxnhwcrRCbJ2hDPLmWVER+tPITPwqp
R8qVGY3K6axG68b964B/hsACjRF7C1lqRQsiQbi8pVPPGEhekmgnW8hF6dNdy1VW
wVo8F0GCST6jLk9YFbirBdKsDRJTLc+WsyP6jUZyWkrrM6p4ycs+voGFDNZbhPw=
=CXyd
-----END PGP SIGNATURE-----
Merge tag 'at91-3.5-cleanup' of git://github.com/at91linux/linux-at91 into next/cleanup
Nicolas Ferre <nicolas.ferre@atmel.com> writes:
First batch of AT91 cleanup for 3.5 kernel.
- The biggest improvement of this series is the ability to compile several
AT91 SoCs in one kernel image.
For now on it's limited to the DT-enabled boards but we can compile all
the core together.
- The Kconfig series is stacked before other patches as it is simple and
non-intrusive. Its goal is to remove too restrictive dependencies on
SoC names. This will allow to add support for newer SoC seamlessly.
- Some very "cosmetic" Kconfig changes are also added (entry names,
comments, etc.).
* tag 'at91-3.5-cleanup' of git://github.com/at91linux/linux-at91: (19 commits)
ARM: at91: add defconfig for device tree
ARM: at91/dt: do not specify the board any more
ARN: at91: introduce SOC_AT91xxx define to allow to compile SoC core support
ARM: at91: add SOC_AT91SAM9 kconfig option to factorise select
ARM: at91: pm select memory controler at runtime
ARM: at91: move at91_init_leds to board init
ARM: at91: do not pin mux the UARTs in init_early
ARM: at91: drop at91_set_serial_console
ARM: at91: uncompress: autodetect the uart to use
ARM: at91: uncompress Store UART address in a variable
hwrng: Kconfig: remove dependency for atmel-rng driver
Input: Kconfig: remove dependency for atmel_tsadcc driver
rtc: Kconfig: remove dependency for AT91 rtc driver
ARM: at91/Kconfig: website link for AT91SAM9G20-EK
ARM: at91/Kconfig: add AT91SAM9x5 family to AT91_EARLY_DBGU0 entry
ARM: at91/Kconfig: add clarifications to AT91SAM9M10G45-EK entry
ARM: at91/Kconfig: add comment to at91sam9x5 family entry
ARM: at91/Kconfig: change at91sam9g45 entry
ARM: at91: change AT91 Kconfig entry comment
Also updates the cleanup branch to v3.4-rc3.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
handle_IRQ may briefly cause interrupts to be re-enabled during soft IRQ
processing on the exit path, leading to nested handling of VIC interrupts.
Since the current code does not re-read the VIC_IRQ_STATUS register, this
can lead to multiple invocations of the same interrupt handler and
spurious interrupts to be reported.
This patch changes the VIC interrupt dispatching code to re-read the
status register each time, avoiding duplicate invocations of the same
handler.
Acked-and-Tested-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
ixp2xxx platforms have had no real changes since ~2006 and the maintainer
has said on irc that they can be removed:
13:05 < nico> do you still care about ixp2000?
13:22 < lennert> not really, no
13:58 < nico> do you think we could remove it from the kernel tree?
14:01 < lennert> go for it, and remove ixp23xx too while you're at it
Removing will help simplify ARM consolidation in general and PCI re-work
specifically.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Pull more ARM updates from Russell King.
This got a fair number of conflicts with the <asm/system.h> split, but
also with some other sparse-irq and header file include cleanups. They
all looked pretty trivial, though.
* 'for-linus' of git://git.linaro.org/people/rmk/linux-arm: (59 commits)
ARM: fix Kconfig warning for HAVE_BPF_JIT
ARM: 7361/1: provide XIP_VIRT_ADDR for no-MMU builds
ARM: 7349/1: integrator: convert to sparse irqs
ARM: 7259/3: net: JIT compiler for packet filters
ARM: 7334/1: add jump label support
ARM: 7333/2: jump label: detect %c support for ARM
ARM: 7338/1: add support for early console output via semihosting
ARM: use set_current_blocked() and block_sigmask()
ARM: exec: remove redundant set_fs(USER_DS)
ARM: 7332/1: extract out code patch function from kprobes
ARM: 7331/1: extract out insn generation code from ftrace
ARM: 7330/1: ftrace: use canonical Thumb-2 wide instruction format
ARM: 7351/1: ftrace: remove useless memory checks
ARM: 7316/1: kexec: EOI active and mask all interrupts in kexec crash path
ARM: Versatile Express: add NO_IOPORT
ARM: get rid of asm/irq.h in asm/prom.h
ARM: 7319/1: Print debug info for SIGBUS in user faults
ARM: 7318/1: gic: refactor irq_start assignment
ARM: 7317/1: irq: avoid NULL check in for_each_irq_desc loop
ARM: 7315/1: perf: add support for the Cortex-A7 PMU
...
Dave Martin