Since all wext specific code is removed, currently there is no
way to configure deep sleep mode. This patch removes deep sleep
configuration information in readme file.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch also deletes the now unused parts of rtl8192de/def.h.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Chaoming Li <chaoming_li@realsil.com.cn>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch also deletes the now unused parts of rtl8192se/def.h.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Chaoming Li <chaoming_li@realsil.com.cn>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch also removes the now unused code from rtl8192ce/def.h.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Chaoming Li <chaoming_li@realsil.com.cn>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Chaoming Li <chaoming_li@realsil.com.cn>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In preparation for fixing the rate-mapping situation, place a driver-agnostic
version in rtlwifi. This one contains the updated rate incormation.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Chaoming Li <chaoming_li@realsil.com.cn>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Test the just-initialized value rather than some other one.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r@
identifier x,y,f!={PTR_ERR,ERR_PTR,ERR_CAST};
statement S;
@@
x = f(...);
(
if (\(x == NULL\|IS_ERR(x)\)) S
|
*if (\(y == NULL\|IS_ERR(y)\))
{ ... when != x
return ...; }
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This removes the "FWxx" ID strings from the b43 and b43legacy
drivers. They were once used to match a specific driver revision
to a set of firmware files. However, this is hardly useful today.
Additionally, the IDs are not updated and maintained properly, so
they might mislead users.
Signed-off-by: Michael Buesch <m@bues.ch>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The Walsh bit is disabled for regulatory consideration.
FCC limit for walsh enable is lower than that for walsh disable. So
disabling walsh bit will not limit tx power/affect tx power even in
cases where we are not FCC limited (most client cards). If the tx
power is not FCC limited, then enabling/disabling walsh bit will
not affect Avg. EVM/overall performance in any visible manner.
Cc: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In congested network, having all rate reties at MCS rates
is failing to transmit the frame offenly. By the time reaching
the success rate set, the application gets timed out. One such
scenario is that authentication time out during 4-Way handshake.
This patch uses a legacy rate as last retry sequnce for
unaggregated frames or if the first selected rate's PER is ~80%
of max limit. And also observed from the tx status that the frame
was trasmitted successfully by using legacy rates.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
this useful for debugging and to keep track of success/failure of
frames such as ACK, RTS and FCS error count in a noisy environment
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The firmware keeps track of channel usage. This data can
be used by the automatic channel selection to find the best
channel.
Survey data from wlan4
frequency: 5200 MHz [in use]
noise: -91 dBm
channel active time: 811909 ms
channel busy time: 63395 ms
channel transmit time: 59636 ms
Survey data from wlan4
frequency: 5210 MHz
noise: -91 dBm
channel active time: 121 ms
channel busy time: 119 ms
channel transmit time: 0 ms
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Prevent 8 bytes from being truncated from MGMT packets
when using TKIP.
Signed-off-by: Bill Jordan <bjordan@rajant.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We have resolved all the known issues with DMA mode, however some users
(or distros) are still forcing PIO mode by config files. Without
debugging enabled it's not noticable at all. Add the warning for them.
Cc: Gregory Bellier <gregory.bellier@gmail.com>
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The EIFS value read from AR_D_GBL_IFS_EIFS register in core clocks and then
written back as microsecond value.
Signed-off-by: Alex Hacker <hacker@epn.ru>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All AR9170 hardware have a 16-Bit random number generator.
The documentation claims the values are suitable for
"security keys".
The "throughput" is around 320Kibit/s. It's slow, but it
does work without introducing any special offload
firmware commands.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The firmware keeps track of channel usage. This data can
be used by the automatic channel selection to find the
*best* channel.
Survey data from wlan22
frequency: 2412 MHz [in use]
noise: -86 dBm
channel active time: 3339608 ms
channel busy time: 270982 ms
channel transmit time: 121515 ms
Survey data from wlan22
frequency: 2417 MHz
noise: -86 dBm
channel active time: 70 ms
channel busy time: 2 ms
channel transmit time: 1 ms
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Import new headers from our firmware branch:
git://git.kernel.org/pub/scm/linux/kernel/git/chr/carl9170fw.git
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR9170_PWR_REG_PLL_ADDAC is used to set the main clock
divisor which affects the AHB/CPU speed. Because this
would interfere with the firmware internal timekeeping,
the function has to be moved into the firmware.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There was an extra semicolon so the if condition wasn't used. We
checked "priv->dev" twice instead of "priv->mesh_dev".
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
They were taken from MMIO dump with few RegExps and vim.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Analog is switched on right after reading PHY version:
read16 0xfaafc3e0 -> 0xa801
phy_read(0x043b) -> 0x0000
phy_write(0x043b) <- 0x0000
Switched off after after killing radio:
>>> Switch Radio(OFF) end
phy_read(0x043c) -> 0x0000
phy_write(0x043c) <- 0x0007
phy_read(0x043b) -> 0x0000
phy_write(0x043b) <- 0x0007
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some hardware with 64-bit DMA uses lower address word for setting
routing (translation) bit. Add workaround for such boards.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On embedded hardware it's normal to not have a PCI device for the PCI
bridge that the wifi card is attached to. pdev->bus->self will be
NULL in that case. In that case, simply return without emitting an
useless kernel stack trace.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While switching b/w HT20/40, the current channel's nf values
are updated into history buffer. Since the current channel's
channel type, channel flag got updated before reading
nf value from hw. This channel type mismatch is causing invalid
readings when hw is on ht20 but getnf tries to read on extn chains.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Before doing hw reset the current channel's noisefloor readings
are updated into history buffer. The extension chain's readings
are considered only if the current channel was configured in HT40.
While moving from HT40 to HT20, the extn chain's readings are
skipped though the current channel is in ht40. This patch updates
extn chain reading based on channel flag.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The chainmasks were already configured at process_ini
before doing init calibration.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Once RXEOL was disabled, it never be enabled again. This patch
re-enables rxeol at the end of rx tasklet.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Whenever RXEOL is received, both RXORN and RXEOL got cleared
to avoid rx overrun interrupt storm. This was handled only for
edma chips. The same scenario was also observered with AR9280,
doing frequent channel type switch b/w HT20/40 with bidi traffic
that is causing failure to stop rx dma. This patch clears
the RXEOL & RXORN interrupts for all chips.
ath: DMA failed to stop in 10 ms AR_CR=0x00000024 AR_DIAG_SW=0x42000020
DMADBG_7=0x000062c0
ath: Could not stop RX, we could be confusing the DMA engine when we
start RX up
------------[ cut here ]------------
WARNING: at drivers/net/wireless/ath/ath9k/recv.c:532
ath_stoprecv+0x110/0x120 [ath9k]()
Call Trace:
[<ffffffff8104a55a>] warn_slowpath_common+0x7a/0xb0
[<ffffffff8104a5a5>] warn_slowpath_null+0x15/0x20
[<ffffffffa0560380>] ath_stoprecv+0x110/0x120 [ath9k]
[<ffffffffa055e6fa>] ath_reset+0x6a/0x200 [ath9k]
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The WAR which adds extra delimiters when using RTS/CTS
with aggregation and non-enterprise AR9003 chips.
This extra padding is done after doing all the 4ms limit
checks and hence the total aggregate sizes are exceeding
the allowed duration. This patch limits the aggregate
sizes appropriately after including these extra delimiters.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sometimes we need to write table which is 2-10 elements long. It's
easier to create such a function instead of defining array every time.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
No need to recompile the module anymore to set the debug level.
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
MMIO hacks were used to trick ndis&wl. For example following:
phy_read(0x0280) -> 0xffff
phy_write(0x0280) <- 0xff3e
***
phy_read(0x0280) -> 0x0000
phy_write(0x0280) <- 0x003e
was translated to mask 0xff00 and set 0x3e.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a client disassociates from a crypto enabled bss, data traffic to
other clients connected to the bss is stalled. This was due to a boolean
variable used to keep track if HW crypto is enabled i.e. if set key has
been called to add a key. This flag was being reset every time delete
key was called e.g when a station leaves the bss. Once the flag is
reset, rx status flags were not being set for connected clients which
disrupts traffic to these clients. Fix this issue by not resetting the
flag since we do not need to reset this flag during the life time of the
bss.
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Replace "old" and "new" with number of the first firmware known to use
the given format.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
b43_op_config and b43_op_bss_info_changed apply many settings by directly
writing to hardware registers. These settings are lost as soon as the core
is restarted and the initvals are reloaded. This was discovered because
restarting hostapd led to the beacon interval getting set to ~33s (see
https://dev.openwrt.org/ticket/8033 for more information).
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Disable ASPM in pci ->probe on upstream (device) and downstream
(PCIe port) component. According to e1000e driver authors this is
required. I did not find that requirement in PCIe spec, but it seems
to be logical for me.
This need to be fixed for CONFIG_PCIEASPM, that will be done later ...
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move common checks into wrapper function. Since ASPM can be only enabled
on PCIe devices ->is_pciexpress check is unneeded.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We always call ->config_pci_powersave() with both restore and power_off
arguments equal to 0 or both equal to 1, so merge them into one
argument.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Only increment the queue count after actually queuing the skb. This
avoids a spurious increment is case of dropped packets.
Also move the Tx-watermark checking code after the packet is enqueued.
This makes the count more accurate - it includes the just-queued
packet.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Don't pollute the queues with Tx directed to invalid stations. This
can happen during recovery.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
This fix eliminates a potential race between starting the AP role
and setting encryption keys.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
This adjusts FW TX block allocation for connected stations in PS.
Firmware congestion is measured in allocated packets instead of blocks.
Allow a link in PS to queue up to 2 packets to the FW.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Sometimes the fw doesn't send the DISCONNECT_EVENT_COMPLETE_ID
on station role stop, so don't wait for it.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
When the FW Tx released blocks counter wraps around, we should correct
our calculation of released blocks. Otherwise we add a large negative
figure to our driver freed blocks counter
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
When selecting packets for transmission, prefer the ACs that are least
occupied in the FW. When packets for multiple ACs are present in the FW,
it decides which to transmit according to WMM QoS parameters.
With these changes, lower priority ACs should not be starved when higher
priority traffic is present.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Track the number of freed packets in each AC when receiving an interrupt
from the FW. This paves the way for tracking allocated packets per AC.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
When wep key was removed after disconnection, sta_hlid was invalid,
and it resulted in a fw crash.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
when the key was recorded, wl->ap_bcast_hlid was invalid
(since the role wasn't started), so when configuring the
key we need to use the current ap_bcast_hlid.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Unconditionally configure HT rate support to the FW on all ACs
when starting the AP.
When 11n support is disabled by usermode (hostapd), each STA joining
the AP will appear as a non-HT STA. This will stop us from accidentally
transmitting using MCS rates.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
When a new STA joins the BSS, configure the HT rates it supports to the
FW.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
In addition, set global HT operation mode via ACX_HT_BSS_OPERATION when
a change is detected by usermode
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Start IBSS role when the interface type is IBSS.
As with sta role, use the dev role until the role
is started.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Add wl12xx_cmd_role_start_ibss() implementation and defintion.
This function is used in order to start the IBSS role.
Stopping the IBSS is done by using the same api as stop STA,
so there is no need for a separate function.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
If hlid was already removed, there is no need to remove
its key (it might cause a fw crash, as the key is invalid).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
After adding a station, call wl12xx_cmd_set_peer_state().
This is required for 11n support.
Change wl12xx_cmd_set_peer_state() prototype to get hlid
as param.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Incorporate interface changes for HT support.
Add ba_bitmap field to the wl1271_link struct, to indicate
activate RX BA sessions (for AP mode).
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Using hlid=0 in AP mode is a bug. Dynamically allocate HLIDs.
Set the "first sta hlid" as 3. This will have to be changed
when multiple vifs will be supported.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The BT coex params api have been changed.
Update it, and init coex for both sta and ap.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The ROC command asks the fw stay on the channel of the given
hlid. it currently has 2 primary functions:
1. Allow tx/rx from the device role.
In order to tx/rx packets while the stations is not associated
(e.g. auth req/resp), the device role has to be used, along
with ROC on its link.
Keep the logic similiar to the one used in dummy_join. However,
since we can't scan while we ROC, we add CROC before starting
a scan, and ROC again (if needed) on scan complete.
2. Keeping the antenna for a specific link.
We ROC until the connection was completed (after EAPOLs exchange)
in order to prevent BT coex operations from taking the antenna
and failing the connection (after this stage, psm can be used).
During association, we ROC on the station role, and then CROC
the device role, thus assuring being ROC during all the connection
process.
Delete the WL1271_FLAG_JOINED flag, and use a roc bitmap
to indicate what roles are currently ROCed.
Add wl12xx_roc/croc functions in order to wrap the roc/croc
commands while taking care of the roc bitmap.
The current ROC/CROC state-machine is a bit complicated. In
the future we'll probably want to use wpa_supplicant to control
the ROC during connection.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Allow handling of DUMMY_PACKET_EVENT_ID also in ap mode.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Add structs and functions to support the ROC/CROC commands.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
system_hlid is a const hlid (always 0), used by the fw and driver
for packets which are not bound to specific role (e.g. dynamic
memory packets).
indicate it as always allocated.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Use ACX_BEACON_FILTER_OPT for both station and ap roles
(use the generic wl1271_acx_beacon_filter_opt()
instead of wl1271_acx_set_ap_beacon_filter() ).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The max template size was increased in the new fw.
However, we should use the max size only when needed, as it
consumes some of the chip's memory.
Thus, by default initialize the templates to the default size.
Initialize to the maximum size only when required.
Use WL1271_CMD_TEMPL_DFLT_SIZE instead of some of the
predefined structs, as some of them didn't account
for additional IEs that might be added to the template.
Delete structs defintions not used after these changes.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Update the rx/tx descriptors according to the new fw api
(fw >= 6/7.3.0.0.75)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Update the scan command to use the new fw api
(fw 6/7.3.0.0.75).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The device role is a special role used for rx and tx frames
prior to association (as the STA role can get packets only
from its associated bssid)
Since this role is required for the sta association process,
we enable it when a new sta interface is created.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
According to the new multi-role flow, we have to enable the
role before using (starting) it, and disable it on cleanup
(after it's no longer needed).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Change the commands and events according to the new fw api
(fw >= 6/7.3.0.0.75).
The main change is the replacement of JOIN/DISCONNECT commands,
with ROLE_START/ROLE_STOP commands.
The use of these commands should be preceded by the ROLE_ENABLE
command (allocating role resources), and followed by the
ROLE_DISABLE command (freeing role resources).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Update the acx commands according to the new fw api
(fw >= 6/7.3.0.0.75).
The main change in most of the ACXs is the addition
of a new role_id/link_id field, which is required
for multi-role operation.
Currently, we don't really support multi-role, as
most of our data (inside wl) is global.
As the current fw doesn't support concurrent roles
yet, keep it this way and add wl->role_id and
wl->sta_hlid to save the active role/link.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Update the fw status struct according to the new fw api
(fw >= 6/7.0.0.35).
All the roles use the same struct now.
The memory accounting was changed a bit according to
the struct changes.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The new fw doesn't support rx_filtering configuration (as a
stand-alone command. the rx filtering is done automatically
according to the active role).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
In order to keep to driver compiling during the patchset,
while avoiding one-huge-patch, temporarily disable some
advanced ap functions.
These changes will be reverted later in the patchset, as
part of the patches for advanced ap functions support.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
This does not make sense in fw >= 6/7.3.0.0.75 (wl127x/wl128x) -
we don't use Tx blocks to measure FW occupancy anymore.
This reverts commit 9e374a37b6.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Instead of maintaining static scan table in driver, scan list is sent
to cfg80211 stack (after parsing each scan command response).
In assoc handler (for infra and ibss network) requested BSS information
is retrieved using cfg80211_get_bss() API.
With the changes above some redundant code are removed.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If the driver gets a tx status report for an A-MPDU sent to a station that
just went to sleep, that leaves a race condition where this tx status can
trigger another A-MPDU transmission.
To fix this, check if the station is sleeping before queueing the tid.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k_hw_4k_get_eeprom() overrides the eeprom value for txgain if the
minor version is not 19 or above with a value of 0.
ar9002_hw_init_mode_gain_regs() relies on this information to
determine whether this is a high power wifi card or not. The override
caused the driver to always use the 'normal' power tables even for
high power devices if their minor version was not high enough. Thus
leading to reduced power output.
This isn't needed for the AR9285; the check originated with the
AR9280 setup code which requires the EEPROM version check.
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Adrian Chadd <adrian@freebsd.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix the value of PG version for 128x at sysfs, remove write permissions
from PG version (hw_pg_ver) in sysfs and add remove files
(hw_pg_ver,bt_coex_state) from sysfs while freeing hardware.
New macro names for register Fuse_data_2_1 depend on architecture.
Propagate chip id through wiphy in PLT mode which still not work of
a bug in ethtool.
Signed-off-by: Gery Kahn <geryk@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
In case of QoS packets the packet payload isn't aligned to
4 bytes. In that case the mac80211 layer take care of that
via memmove() in ieee80211_deliver_skb().
Add support of copy packets from aggregation buffer to the
skbs with packet payload aligned care. In case of QoS packets
copy the packets in offset of 2 bytes guarantee payload aligned
to 4 bytes.
Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
the comments are obselete as the virtual wiphy support was removed from
the driver
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
for the ease of debugging, we display only the rate control statistics
for currently operating mode and bandwidth
Cc: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Cc: "Balasubramanian, senthilkumar" <senthilb@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
RX_FLAG_HT must be included when reporting MCS rates. Without
this, mac80211 ended up dropping any frame sent at MCS index 12
or higher and that resulted in oddly random looking errors in
mac80211_hwsim tests.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Stephen reported that compilation fails if both ath6kl and ath9k are
compiled in:
drivers/net/wireless/ath/ath6kl/built-in.o: In function `htc_start':
(.opd+0x600): multiple definition of `htc_start'
drivers/net/wireless/ath/ath9k/built-in.o:(.opd+0x3e40): first defined here
drivers/net/wireless/ath/ath6kl/built-in.o: In function `.htc_stop':
(.text+0x7b40): multiple definition of `.htc_stop'
drivers/net/wireless/ath/ath9k/built-in.o:(.text+0x67b34): first defined he=
re
drivers/net/wireless/ath/ath6kl/built-in.o: In function `.htc_start':
(.text+0x7d18): multiple definition of `.htc_start'
drivers/net/wireless/ath/ath9k/built-in.o:(.text+0x67ba0): first defined he=
re
drivers/net/wireless/ath/ath6kl/built-in.o: In function `htc_stop':
(.opd+0x5e8): multiple definition of `htc_stop'
drivers/net/wireless/ath/ath9k/built-in.o:(.opd+0x3e28): first defined here
To fix this add ath6kl prefix to all public functions in htc.c.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Since kernel 3.0, the problems with controlling b43 devices that have
low-power (LP) PHYs have been fixed and the EXPERIMENTAL designation
can be fixed.
This patch also fixes a typo as the device supports 802.11b communications.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We always hit the goto and skip the printk(). The original code does
the right thing even though it looks messy.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When toggle_irq is called for PCI devices to disable device interrupts
it used tasklet_disable to wait for a possibly running tasklet to finish.
However, on SMP systems the tasklet might still be scheduled on another CPU.
Instead, use tasklet_kill to ensure that all scheduled tasklets are finished
before returning from toggle_irq.
Furthermore, it was possible that a tasklet reenabled its interrupt even
though interrupts have been disabled already. Fix this by checking the
DEVICE_STATE_ENABLED_RADIO flag before reenabling single interrupts
during tasklet processing.
While at it also enable/kill the TBTT and PRETBTT tasklets in the
toggle_irq callback and only use tasklet_kill in stop_queue to wait
for a currently scheduled beacon update before returning.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now that the driver no longer uses the raw r/w routines, remove their definitions.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The PCIe driver used raw reads and writes on the PCIe hardware.
As all of these are only affecting the configuration space, all of
then can be converted to pci_{read,write}_config_XX calls.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Let us enable/disable interrupts based on reference count.
By doing this we can ensure that interrupts are never be
enabled in the middle of tasklet processing. Instead of
addressing corner cases like "ath9k: avoid enabling interrupts
while processing rx", this approach handles it in generic manner.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Spur frequency was incorrectly computed with 10Mhz offset
which could cause the filter would not notch out the spur
and also this could improve rx sensitivity in HT40.
Cc: Madhan Jaganathan <madhanj@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
At preset set_interrupt also enables interrupt after changing
mask. This is not necessary in all cases and also sometime it
breaks the assumption that interrupt was disabled. So let us
enable the interrupt explicity if it was disabled earlier.
This could also avoid unnecessary register ops and also helps
the follow up patch to have global ref count for interrupts ops.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add code to display driver version information in dmesg after
loading the driver successfully.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The SDIO card is now fully powered down when the network interface is
brought down.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Modify the driver so that it does not function when the interface is
down, in preparation for runtime power management.
No commands can be run while the interface is down, so the ndo_dev_stop
routine now directly does all necessary work (including asking the device
to disconnect from the network and disabling multicast functionality)
directly.
power_save and power_restore hooks are added meaning that card drivers
can take steps to turn the device off when the interface is down.
The MAC address can now only be changed when all interfaces are down;
the new address will be programmed when an interface gets brought up.
This matches mac80211 behaviour.
Also, some small cleanups/simplifications were made in the surrounding
device handling logic.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The high_power tx gain table is changed to match the low_ob_db tx gain
table for both 5G and 2G.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
No need to process RxDone and ds_info status again in case
valid rx status is given.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch cleanups virtual wiphy specific frametype structure
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This ieee80211 core was found on a Netgear wndr3400.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Nowhere the firmware memory is freed, free it during
the device destroy process.
Signed-off-by: Raja Mani <rmani@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Sometimes, the network manager is failing to connect to the AP due
to the below kernel crash message. The reason behind this,
after issuing the connect command to the chip, the chip is sending
disconnect event and then immediately one connect event to the host
in some random cases.
The host driver resets all states (including cfg80211 state machine)
when it receives disconnect event from the chip. But, still the host
driver reports the next received connect event to cfg80211, at that time
cfg80211 SME state would have been in IDLE state, which was causing
the below kernel crash.
Now, host driver's sme state machine is checked every time before
delivering connect event to cfg80211
WARNING: at net/wireless/sme.c:517 cfg80211_connect_result+0x10d/0x120()
[..]
Call Trace:
[<c0145732>] warn_slowpath_common+0x72/0xa0
[<c05d676d>] ? cfg80211_connect_result+0x10d/0x120
[<c05d676d>] ? cfg80211_connect_result+0x10d/0x120
[<c0145782>] warn_slowpath_null+0x22/0x30
[<c05d676d>] cfg80211_connect_result+0x10d/0x120
[<f83ff497>] ath6kl_cfg80211_connect_event+0x427/0x4f0 [ath6kl]
[<c035d26a>] ? put_dec+0x2a/0xa0
[<c035d645>] ? number+0x365/0x380
[<c0154675>] ? mod_timer+0x135/0x260
[<c035e00e>] ? format_decode+0x2fe/0x370
[<c01263c8>] ? default_spin_lock_flags+0x8/0x10
[<c05fd91f>] ? _raw_spin_lock_irqsave+0x2f/0x50
[<c0146032>] ? console_unlock+0x172/0x1c0
[<f8402659>] ath6kl_connect_event+0x89/0x400 [ath6kl]
[<f840826e>] ath6kl_wmi_control_rx+0x98e/0x1d60 [ath6kl]
[<c01335b5>] ? __wake_up+0x45/0x60
[<f84053aa>] ath6kl_rx+0x56a/0x770 [ath6kl]
[<c04d0242>] ? mmc_release_host+0x22/0x40
[<c04d9329>] ? sdio_release_host+0x19/0x30
[<f840a27a>] ? ath6kl_sdio_read_write_sync+0x7a/0xc0 [ath6kl]
[<f83f82b1>] do_rx_completion+0x41/0x50 [ath6kl]
[<f83faa6a>] htc_rxmsg_pending_handler+0x6ba/0xbd0 [ath6kl]
[<f8404bb0>] ? ath6kl_tx_data_cleanup+0x30/0x30 [ath6kl]
[<f840a1c0>] ? ath6kl_sdio_irq_handler+0x30/0x70 [ath6kl]
[<f83f7cd5>] ath6kldev_intr_bh_handler+0x2a5/0x630 [ath6kl]
[<f840a1c0>] ath6kl_sdio_irq_handler+0x30/0x70 [ath6kl]
[<c04d97c7>] sdio_irq_thread+0xc7/0x2d0
[<c013aeb0>] ? default_wake_function+0x10/0x20
[<c012fc98>] ? __wake_up_common+0x48/0x70
[<c04d9700>] ? sdio_claim_irq+0x200/0x200
[<c0163854>] kthread+0x74/0x80
[<c01637e0>] ? kthread_worker_fn+0x160/0x160
[<c0604c06>] kernel_thread_helper+0x6/0x10
Signed-off-by: Raja Mani <rmani@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Use wlan_iterate_nodes() directly.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
By having scan_table in struct ath6kl, it makes sense to move initialization
to ath6kl_init() and deinitialization to ath6kl_destroy().
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Use the bssid from ath6kl directly.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This is nothing but bssid of struct ath6kl.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
And remove the reference to wmi in ath6kl_node_table.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When I connect to my Linksys WT610N AP supporting 11n I see a lot of
aggreation timeout errors:
[ 408.885053] ath6kl: aggr timeout (st 3109 end 3140)
[ 463.872108] ath6kl: aggr timeout (st 3671 end 3702)
[ 495.010060] ath6kl: aggr timeout (st 3983 end 4014)
[ 503.604047] ath6kl: aggr timeout (st 4065 end 0)
[ 518.963047] ath6kl: aggr timeout (st 141 end 172)
[ 525.014066] ath6kl: aggr timeout (st 205 end 236)
[ 573.957051] ath6kl: aggr timeout (st 701 end 732)
[ 585.019067] ath6kl: aggr timeout (st 816 end 847)
But still the connection seems to work. To not clutter the logs change
the error message to a debug message. But add a fixme comment so that
this will be investigated.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath6kl Kconfig still had dependencies to wext, remove those as they are
not needed anymore.
Now ath6kl should not have any wext code left. Time to have a beer and
celebrate this.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When ath6kl module was removed while a scan was ongoing the driver would
crash in ath6kl_cfg80211_scan_complete_event().
Fix the function not to iterate nodes when the scan is aborted. The nodes
are already freed when the module is being unloaded. This patch removes the
null check entirely as the wmi structure is not accessed anymore during
module unload.
Also fix a bug where the status was checked as a bitfield with '&' operator.
But it's not a bitfield, just a regular error code.
This is a port of my patch from ath6kl staging with the same title.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath6kl_cfg80211_scan_node() was calling cfg80211_inform_bss_frame()
with CFP_KERNEL but the function is executed with a spin lock taken.
This is wrong and the function must use GFP_ATOMIC instead.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In my setup data transfer stalls when there's data transmission during
scan. After some testing I found out that using background scan
when connected to makes the problem go away. This is more like
a workaround than a proper fix, but as the stall is so severe the
workaround is justified.
With a dual band card this increases scan time when connected from
1.9s to 4.4s. When not connected the scan time is not affected and
is the same 1.9s.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Use appropriate hif function directly.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Endpoint id ffrom htc_packet can be used instead.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Define a hook in ath6kl_hif_ops for hif scatter gather mechanism.
When virtual scatter gather is used, call the respective function
directly.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Last May we started working on cleaning up ath6kl driver which is
currently in staging. The work has happened in a separate
ath6kl-cleanup tree:
http://git.kernel.org/?p=linux/kernel/git/kvalo/ath6kl-cleanup.git;a=summary
After over 1100 (!) patches we have now reached a state where I would
like to start discussing about pushing the driver to the wireless
trees and replacing the staging driver.
The driver is now a lot smaller and looks like a proper Linux driver.
The size of the driver (measured with simple wc -l) dropped from 49
kLOC to 18 kLOC and the number of the .c and .h files dropped from 107
to 22. Most importantly the number of subdirectories reduced from 26
to zero :)
There are two remaining checkpatch warnings in the driver which we
decided to omit for now:
drivers/net/wireless/ath/ath6kl/debug.c:31:
WARNING: printk() should include KERN_ facility level
drivers/net/wireless/ath/ath6kl/sdio.c:527:
WARNING: msleep < 20ms can sleep for up to 20ms;
see Documentation/timers/timers-howto.txt
The driver has endian annotations for all the hardware specific
structures and there are no sparse errors. Unfortunately I don't have
any big endian hardware to test that right now.
We have been testing the driver both on x86 and arm platforms. The
code is also compiled with sparc and parisc cross compilers.
Notable missing features compared to the current staging driver are:
o HCI over SDIO support
o nl80211 testmode
o firmware logging
o suspend support
Testmode, firmware logging and suspend support will be added soon. HCI
over SDIO support will be more difficult as the HCI driver needs to
share code with the wifi driver. This is something we need to research
more.
Also I want to point out the changes I did for signed endian support.
As I wasn't able to find any support for signed endian annotations I
decided to follow what NTFS has done and added my own. Grep for sle16
and sle32, especially from wmi.h.
Various people have been working on the cleanup, the hall of
fame based on number of patches is:
543 Vasanthakumar Thiagarajan
403 Raja Mani
252 Kalle Valo
16 Vivek Natarajan
12 Suraj Sumangala
3 Joe Perches
2 Jouni Malinen
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Raja Mani <rmani@qca.qualcomm.com>
Signed-off-by: Vivek Natarajan <nataraja@qca.qualcomm.com>
Signed-off-by: Suraj Sumangala <surajs@qca.qualcomm.com>
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Currently ath9k presents the internal calibrated noise floor as channel
noise measurement, however this results in highly chip specific values
that are only useful as relative measurements but do not resemble any
real channel noise values.
In order to give a much better approximation of the real channel noise,
add the difference between the measured noise floor and the nominal
chip specific noise floor to the default minimum channel noise value,
which is currently used to calculate the signal strength from the RSSI
value. This may not be 100% accurate, but it's much better than what's
there before.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
OLPC power management code has recently gone upstream. This piece
completes the puzzle for libertas_usb, which now programs the OLPC EC
for wlan wakeups when they have been requested.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When testing for tx power, bypass the default limits.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the previously calculated maximum of all rates instead of just the one
from the lowest rate of the selected PHY mode.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove unnecessary includes from base.h. Add includes to other files as
necessary. Don't include base.h unless needed.
Move declarations for functions in base.c from ath5k.h to base.h.
Use a better named define to protect base.h against double inclusion.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Without CONFIG_HERMES_PRISM, only match cards that have "Version 01.01"
as the third product ID. Those have Agere firmware.
With CONFIG_HERMES_PRISM, match all 0x0156:0x0002 cards.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cards with numeric ID 0x0156:0x0002 and third ID "Version 01.02" can be
assumed to have Intersil firmware. Cards with Agere firmware use
"Version 01.01".
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Pavel Roskin <proski@gnu.org>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Devices supported by b43legacy don't support 64-bit DMA.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add support for v2 of enhanced sensitivity table for 2000 series products
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update the default sensitivity value for both 5000 and 6000 series devices
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The previous P2P implementation turned out to
not work well and new uCode capabilities were
added to support P2P. Modify the driver to
take advantage of those, and also discover P2P
support automatically based on a uCode flag
instead of having a Kconfig symbol for P2P.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The availability of contexts depends on the
firmware capabilities. Currently only the
presence of the second context depends on it,
but soon P2P support will also be different.
Move the context initialisation code to the
firmware-dependent setup before registering
with mac80211 to make it easier to handle.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We're working on improvements for the firmware
for some devices, and need to bump the API for
those since they won't be backward compatible
completely (the earlier patch reserving queue
10 for P2P).
Bump the API version to 6 for those devices
but don't warn users of version 5 yet.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We sometimes need to support new firmware API for
a while before we can publish them since testing
them fully takes a long time. We could keep all
the new code private, but that causes plenty of
problems and sometimes we can give a pre-release
version of firmware to people who need to test.
However, when we just bump the API version, the
driver will warn everybody that their firmware is
outdated, when in fact it isn't. (Currently our
case for this doesn't really change the API but
bumping the API version is necessary because the
firmware isn't fully backward compatible)
In order to handle this in the future, add a new
"api_ok" version; only below this will the driver
warn that the uCode is too old.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For _bgn device, remove ht40 support for 5.2GHz, it is probably ok since
the "band" is not support but just feel strange.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Amitkumar Karwar