Allow KVM_ENABLE_CAP to act on a vm as well as on a vcpu. This makes more
sense when the caller wants to enable a vm-related capability.
s390 will be the first user; wire it up.
Reviewed-by: Thomas Huth <thuth@linux.vnet.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
The code to check whether rd > MIPS_CP0_DESAVE is dead code, since
MIPS_CP0_DESAVE = 31 and rd is already masked with 0x1f. Remove it.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Sanjay Lal <sanjayl@kymasys.com>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The ability to read hardware registers from userland with the RDHWR
instruction should depend upon the corresponding bit of the HWREna
register being set, otherwise a reserved instruction exception should be
generated.
However KVM's current emulation ignores the guest's HWREna and always
emulates RDHWR instructions even if the guest OS has disallowed them.
Therefore rework the RDHWR emulation code to check for privilege or the
corresponding bit in the guest HWREna bit. Also remove the #if 0 case
for the UserLocal register. I presume it was there for debug purposes
but it seems unnecessary now that the guest can control whether it
causes a guest exception.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Sanjay Lal <sanjayl@kymasys.com>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Previously a reserved instruction exception while in guest code would
cause a KVM internal error if kvm_mips_handle_ri() didn't recognise the
instruction (including a RDHWR from an unrecognised hardware register).
However the guest OS should really have the opportunity to catch the
exception so that it can take the appropriate actions such as sending a
SIGILL to the guest user process or emulating the instruction itself.
Therefore in these cases emulate a guest RI exception and only return
EMULATE_FAIL if that fails, being careful to revert the PC first in case
the exception occurred in a branch delay slot in which case the PC will
already point to the branch target.
Also turn the printk messages relating to these cases into kvm_debug
messages so that they aren't usually visible.
This allows crashme to run in the guest without killing the entire VM.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Sanjay Lal <sanjayl@kymasys.com>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The whitespace in asm/kvm_host.h is quite inconsistent in places. Clean
up the whole file to use tabs more consistently.
When you use the --ignore-space-change argument to git diff this patch
only changes line wrapping in TLB_IS_GLOBAL and TLB_IS_VALID macros.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Sanjay Lal <sanjayl@kymasys.com>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When registering a new irqfd, we call its ->poll method to collect any
event that might have previously been pending so that we can trigger it.
This is done under the kvm->irqfds.lock, which means the eventfd's ctx
lock is taken under it.
However, if we get a POLLHUP in irqfd_wakeup, we will be called with the
ctx lock held before getting the irqfds.lock to deactivate the irqfd,
causing lockdep to complain.
Calling the ->poll method does not really need the irqfds.lock, so let's
just move it after we've given up the irqfds.lock in kvm_irqfd_assign().
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When doing nested virtualization, we may be able to read BNDCFGS but
still not be allowed to write to GUEST_BNDCFGS in the VMCS. Guard
writes to the field with vmx_mpx_supported(), and similarly hide the
MSR from userspace if the processor does not support the field.
We could work around this with the generic MSR save/load machinery,
but there is only a limited number of MSR save/load slots and it is
not really worthwhile to waste one for a scenario that should not
happen except in the nested virtualization case.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This is simple to do, the "host" BNDCFGS is either 0 or the guest value.
However, both controls have to be present. We cannot provide MPX if
we only have one of the "load BNDCFGS" or "clear BNDCFGS" controls.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
XSAVE support for KVM is already using host_xcr0 & KVM_SUPPORTED_XCR0 as
a "dynamic" version of KVM_SUPPORTED_XCR0.
However, this is not enough because the MPX bits should not be presented
to the guest unless kvm_x86_ops confirms the support. So, replace all
instances of host_xcr0 & KVM_SUPPORTED_XCR0 with a new function
kvm_supported_xcr0() that also has this check.
Note that here:
if (xstate_bv & ~KVM_SUPPORTED_XCR0)
return -EINVAL;
if (xstate_bv & ~host_cr0)
return -EINVAL;
the code is equivalent to
if ((xstate_bv & ~KVM_SUPPORTED_XCR0) ||
(xstate_bv & ~host_cr0)
return -EINVAL;
i.e. "xstate_bv & (~KVM_SUPPORTED_XCR0 | ~host_cr0)" which is in turn
equal to "xstate_bv & ~(KVM_SUPPORTED_XCR0 & host_cr0)". So we should
also use the new function there.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
- one regression fix for reducing the amount of ucontrol userspace exits
- get rid of BUG_ONs in hot inner loops
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Fq/F
-----END PGP SIGNATURE-----
Merge tag 'kvm-s390-20140317' of git://git.kernel.org/pub/scm/linux/kernel/git/kvms390/linux into HEAD
Two patches:
- one regression fix for reducing the amount of ucontrol userspace exits
- get rid of BUG_ONs in hot inner loops
Add emulation for 0x66 prefixed instruction of 0f 28 opcode
that has been added earlier.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Since commit 7c470539c9
(s390/kvm: avoid automatic sie reentry) we will run through the C code
of KVM on host interrupts instead of just reentering the guest. This
will result in additional ucontrol exits (at least HZ per second). Let
handle a 0 intercept in the kernel and dont return to userspace,
even if in ucontrol mode.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
CC: stable@vger.kernel.org
The BUG_ON in kvm-s390.c is unreachable, as we get the vcpu per common code,
which itself does this from the private_data field of the file descriptor,
and there is no KVM_UNCREATE_VCPU.
The __{set,unset}_cpu_idle BUG_ONs are not triggerable because the vcpu
creation code already checks against KVM_MAX_VCPUS.
Signed-off-by: Dominik Dingel <dingel@linux.vnet.ibm.com>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Both QEMU and KVM have already accumulated a significant number of
optimizations based on the hard-coded assumption that ioapic polarity
will always use the ActiveHigh convention, where the logical and
physical states of level-triggered irq lines always match (i.e.,
active(asserted) == high == 1, inactive == low == 0). QEMU guests
are expected to follow directions given via ACPI and configure the
ioapic with polarity 0 (ActiveHigh). However, even when misbehaving
guests (e.g. OS X <= 10.9) set the ioapic polarity to 1 (ActiveLow),
QEMU will still use the ActiveHigh signaling convention when
interfacing with KVM.
This patch modifies KVM to completely ignore ioapic polarity as set by
the guest OS, enabling misbehaving guests to work alongside those which
comply with the ActiveHigh polarity specified by QEMU's ACPI tables.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Gabriel L. Somlo <somlo@cmu.edu>
[Move documentation to KVM_IRQ_LINE, add ia64. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Commit 595e4f7e69 ("KVM: PPC: Book3S HV: Use load/store_fp_state
functions in HV guest entry/exit") changed the register usage in
kvmppc_save_fp() and kvmppc_load_fp() but omitted changing the
instructions that load and save VRSAVE. The result is that the
VRSAVE value was loaded from a constant address, and saved to a
location past the end of the vcpu struct, causing host kernel
memory corruption and various kinds of host kernel crashes.
This fixes the problem by using register r31, which contains the
vcpu pointer, instead of r3 and r4.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Commit 7b490411c3 ("KVM: PPC: Book3S HV: Add new state for
transactional memory") incorrectly added some duplicate code to the
guest exit path because I didn't manage to clean up after a rebase
correctly. This removes the extraneous material. The presence of
this extraneous code causes host crashes whenever a guest is run.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When not running in guest-debug mode (i.e. the guest controls the debug
registers, having to take an exit for each DR access is a waste of time.
If the guest gets into a state where each context switch causes DR to be
saved and restored, this can take away as much as 40% of the execution
time from the guest.
If the guest is running with vcpu->arch.db == vcpu->arch.eff_db, we
can let it write freely to the debug registers and reload them on the
next exit. We still need to exit on the first access, so that the
KVM_DEBUGREG_WONT_EXIT flag is set in switch_db_regs; after that, further
accesses to the debug registers will not cause a vmexit.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Unlike other intercepts, debug register intercepts will be modified
in hot paths if the guest OS is bad or otherwise gets tricked into
doing so.
Avoid calling recalc_intercepts 16 times for debug registers.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When preparing the VMCS02, the CPU-based execution controls is computed
by vmx_exec_control. Turn off DR access exits there, too, if the
KVM_DEBUGREG_WONT_EXIT bit is set in switch_db_regs.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When not running in guest-debug mode (i.e. the guest controls the debug
registers, having to take an exit for each DR access is a waste of time.
If the guest gets into a state where each context switch causes DR to be
saved and restored, this can take away as much as 40% of the execution
time from the guest.
If the guest is running with vcpu->arch.db == vcpu->arch.eff_db, we
can let it write freely to the debug registers and reload them on the
next exit. We still need to exit on the first access, so that the
KVM_DEBUGREG_WONT_EXIT flag is set in switch_db_regs; after that, further
accesses to the debug registers will not cause a vmexit.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When not running in guest-debug mode, the guest controls the debug
registers and having to take an exit for each DR access is a waste
of time. If the guest gets into a state where each context switch
causes DR to be saved and restored, this can take away as much as 40%
of the execution time from the guest.
After this patch, VMX- and SVM-specific code can set a flag in
switch_db_regs, telling vcpu_enter_guest that on the next exit the debug
registers might be dirty and need to be reloaded (syncing will be taken
care of by a new callback in kvm_x86_ops). This flag can be set on the
first access to a debug registers, so that multiple accesses to the
debug registers only cause one vmexit.
Note that since the guest will be able to read debug registers and
enable breakpoints in DR7, we need to ensure that they are synchronized
on entry to the guest---including DR6 that was not synced before.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Currently, this works even if the bit is not in "min", because the bit is always
set in MSR_IA32_VMX_ENTRY_CTLS. Mention it for the sake of documentation, and
to avoid surprises if we later switch to MSR_IA32_VMX_TRUE_ENTRY_CTLS.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
It's no longer possible to enter enable_irq_window in guest mode when
L1 intercepts external interrupts and we are entering L2. This is now
caught in vcpu_enter_guest. So we can remove the check from the VMX
version of enable_irq_window, thus the need to return an error code from
both enable_irq_window and enable_nmi_window.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
According to SDM 27.2.3, IDT vectoring information will not be valid on
vmexits caused by external NMIs. So we have to avoid creating such
scenarios by delaying EXIT_REASON_EXCEPTION_NMI injection as long as we
have a pending interrupt because that one would be migrated to L1's IDT
vectoring info on nested exit.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We cannot rely on the hardware-provided preemption timer support because
we are holding L2 in HLT outside non-root mode. Furthermore, emulating
the preemption will resolve tick rate errata on older Intel CPUs.
The emulation is based on hrtimer which is started on L2 entry, stopped
on L2 exit and evaluated via the new check_nested_events hook. As we no
longer rely on hardware features, we can enable both the preemption
timer support and value saving unconditionally.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Move the check for leaving L2 on pending and intercepted IRQs or NMIs
from the *_allowed handler into a dedicated callback. Invoke this
callback at the relevant points before KVM checks if IRQs/NMIs can be
injected. The callback has the task to switch from L2 to L1 if needed
and inject the proper vmexit events.
The rework fixes L2 wakeups from HLT and provides the foundation for
preemption timer emulation.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
"virtio_ccw: fix vcdev pointer handling issues" and noticed just
after it went into git.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=qLB9
-----END PGP SIGNATURE-----
Merge tag 'kvm-s390-20140306' of git://git.kernel.org/pub/scm/linux/kernel/git/kvms390/linux into kvm-next
One fix for virtio-ccw, fixing a problem introduced with
"virtio_ccw: fix vcdev pointer handling issues" and noticed just
after it went into git.
During set offline processing virtio_grab_drvdata() incorrectly
calls dev_set_drvdata() to remove the virtio_ccw_device from the
parent ccw_device's driver data. This is wrong and ends up in a
hang during virtio_ccw_reset(), as the interrupt handler still
has need of the virtio_ccw_device.
A new field 'going_away' is introduced in struct virtio_ccw_device
to control the usage of the ccw_device's driver data pointer in
virtio_grab_drvdata().
Signed-off-by: Heinz Graalfs <graalfs@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
commit 0061d53daf introduced a mechanism to execute a global clock
update for a vm. We can apply this periodically in order to propagate
host NTP corrections. Also, if all vcpus of a vm are pinned, then
without an additional trigger, no guest NTP corrections can propagate
either, as the current trigger is only vcpu cpu migration.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When we update a vcpu's local clock it may pick up an NTP correction.
We can't wait an indeterminate amount of time for other vcpus to pick
up that correction, so commit 0061d53daf introduced a global clock
update. However, we can't request a global clock update on every vcpu
load either (which is what happens if the tsc is marked as unstable).
The solution is to rate-limit the global clock updates. Marcelo
calculated that we should delay the global clock updates no more
than 0.1s as follows:
Assume an NTP correction c is applied to one vcpu, but not the other,
then in n seconds the delta of the vcpu system_timestamps will be
c * n. If we assume a correction of 500ppm (worst-case), then the two
vcpus will diverge 50us in 0.1s, which is a considerable amount.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Implement the new CCW_CMD_SET_IND_ADAPTER command and try to enable
adapter interrupts for every device on the first startup. If the host
does not support adapter interrupts, fall back to normal I/O interrupts.
virtio-ccw adapter interrupts use the same isc as normal I/O subchannels
and share a summary indicator for all devices sharing the same indicator
area.
Indicator bits for the individual virtqueues may be contained in the same
indicator area for different devices.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Add airq_iv_alloc and airq_iv_free to allocate and free consecutive
ranges of irqs from the interrupt vector.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
The interrupt handler virtio_ccw_int_handler() using the vcdev pointer
is protected by the ccw_device lock. Resetting the pointer within the
ccw_device structure should be done when holding this lock.
Also resetting the vcdev pointer (under the ccw_device lock) prior to
freeing the vcdev pointer memory removes a critical path.
Signed-off-by: Heinz Graalfs <graalfs@linux.vnet.ibm.com>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
We can use kvm_get_vcpu() now and don't need the
local_int array in the floating_int struct anymore.
This also means we don't have to hold the float_int.lock
in some places.
Signed-off-by: Jens Freimann <jfrei@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
When SIGP SET_PREFIX is called with an illegal CPU id, it must return
the condition code 3 ("not operational") instead of 1. Also fixed the
order in which the checks are done - CC3 has a higher priority than CC1.
And while we're at it, this patch also get rid of the floating interrupt
lock here by using kvm_get_vcpu() to get the local_int struct of the
destination CPU.
Signed-off-by: Thomas Huth <thuth@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
We don't need to loop over all cpus to get the number of
vcpus. Let's use the available counter online_vcpus instead.
Signed-off-by: Jens Freimann <jfrei@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
For migration/reset we want to expose the guest breaking event
address register to userspace. Lets use ONE_REG for that purpose.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Jason J. Herne <jjherne@linux.vnet.ibm.com>
commit d208c79d63 (KVM: s390: Enable
the LPP facility for guests) enabled the LPP instruction for guests.
We should expose the program parameter as a pseudo register for
migration/reset etc. Lets also reset this value on initial CPU
reset.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Thomas Huth <thuth@linux.vnet.ibm.com>
Reviewed-by: Jason J. Herne <jjherne@linux.vnet.ibm.com>
Commit e504c9098e (kvm, vmx: Fix lazy FPU on nested guest, 2013-11-13)
highlighted a real problem, but the fix was subtly wrong.
nested_read_cr0 is the CR0 as read by L2, but here we want to look at
the CR0 value reflecting L1's setup. In other words, L2 might think
that TS=0 (so nested_read_cr0 has the bit clear); but if L1 is actually
running it with TS=1, we should inject the fault into L1.
The effective value of CR0 in L2 is contained in vmcs12->guest_cr0, use
it.
Fixes: e504c9098e
Reported-by: Kashyap Chamarty <kchamart@redhat.com>
Reported-by: Stefan Bader <stefan.bader@canonical.com>
Tested-by: Kashyap Chamarty <kchamart@redhat.com>
Tested-by: Anthoine Bourgeois <bourgeois@bertin.fr>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Compiling with THP enabled leads to the following warning:
arch/arm/kvm/mmu.c: In function ‘unmap_range’:
arch/arm/kvm/mmu.c:177:39: warning: ‘pte’ may be used uninitialized in this function [-Wmaybe-uninitialized]
if (kvm_pmd_huge(*pmd) || page_empty(pte)) {
^
Code inspection reveals that these two cases are mutually exclusive,
so GCC is a bit overzealous here. Silence it anyway by initializing
pte to NULL and testing it later on.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
In order to be able to detect the point where the guest enables
its MMU and caches, trap all the VM related system registers.
Once we see the guest enabling both the MMU and the caches, we
can go back to a saner mode of operation, which is to leave these
registers in complete control of the guest.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
HCR.TVM traps (among other things) accesses to AMAIR0 and AMAIR1.
In order to minimise the amount of surprise a guest could generate by
trying to access these registers with caches off, add them to the
list of registers we switch/handle.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
So far, KVM/ARM used a fixed HCR configuration per guest, except for
the VI/VF/VA bits to control the interrupt in absence of VGIC.
With the upcoming need to dynamically reconfigure trapping, it becomes
necessary to allow the HCR to be changed on a per-vcpu basis.
The fix here is to mimic what KVM/arm64 already does: a per vcpu HCR
field, initialized at setup time.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Commit 240e99cbd0 (ARM: KVM: Fix 64-bit coprocessor handling)
added an ordering dependency for the 64bit registers.
The order described is: CRn, CRm, Op1, Op2, 64bit-first.
Unfortunately, the implementation is: CRn, 64bit-first, CRm...
Move the 64bit test to be last in order to match the documentation.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Commit 240e99cbd0 (ARM: KVM: Fix 64-bit coprocessor handling)
changed the way we match the 64bit coprocessor access from
user space, but didn't update the trap handler for the same
set of registers.
The effect is that a trapped 64bit access is never matched, leading
to a fault being injected into the guest. This went unnoticed as we
didn't really trap any 64bit register so far.
Placing the CRm field of the access into the CRn field of the matching
structure fixes the problem. Also update the debug feature to emit the
expected string in case of failing match.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Cornelia Huck