Remove the CONFIG_UEVENT_HELPER_PATH because:
1. It is disabled since commit 1be01d4a57 ("driver: base: Disable
CONFIG_UEVENT_HELPER by default") as its dependency (UEVENT_HELPER) was
made default to 'n',
2. It is not recommended (help message: "This should not be used today
[...] creates a high system load") and was kept only for ancient
userland,
3. Certain userland specifically requests it to be disabled (systemd
README: "Legacy hotplug slows down the system and confuses udev").
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Acked-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
MTD_NAND is large and encloses much more than what the symbol is
actually used for: raw NAND. Clarify the symbol by naming it
MTD_RAW_NAND instead.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Remove options which do not exist anymore:
- ECONET is gone since commit 349f29d841 ("econet: remove ancient bug
ridden protocol");
- IPDDP_DECAP is gone since commit 9b5645b513 ("appletalk: remove
"config IPDDP_DECAP"");
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
IDE subsystem has been deprecated since 2009 and the majority
(if not all) of Linux distributions have switched to use
libata for ATA support exclusively. However there are still
some users (mostly old or/and embedded non-x86 systems) that
have not converted from using IDE subsystem to libata PATA
drivers. This doesn't seem to be good thing in the long-term
for Linux as while there is less and less PATA systems left
in use:
* testing efforts are divided between two subsystems
* having duplicate drivers for same hardware confuses users
This patch converts ixp4xx_defconfig to use libata PATA
drivers.
Cc: Imre Kaloz <kaloz@openwrt.org>
Cc: Krzysztof Halasa <khalasa@piap.pl>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
- dts: rename 'ide-disk' to 'disk-activity'
- platform: rename 'ide-disk' to 'disk-activity'
- defconfig: rename 'LEDS_TRIGGER_IDE_DISK' to 'LEDS_TRIGGER_DISK'
Signed-off-by: Stephan Linz <linz@li-pro.net>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
All defconfigs touched by this patch already enable DEBUG_LL and by
default DEBUG_LL_UART_NONE will be selected. This causes no issues
today because due to some back compatibility magic we eventually need
to remove it is not actually honoured. Nevertheless DEBUG_LL_UART_8250
is the right value for these platforms and should be set in the config
files.
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The meaning of CONFIG_EMBEDDED has long since been obsoleted; the option
is used to configure any non-standard kernel with a much larger scope than
only small devices.
This patch renames the option to CONFIG_EXPERT in init/Kconfig and fixes
references to the option throughout the kernel. A new CONFIG_EMBEDDED
option is added that automatically selects CONFIG_EXPERT when enabled and
can be used in the future to isolate options that should only be
considered for embedded systems (RISC architectures, SLOB, etc).
Calling the option "EXPERT" more accurately represents its intention: only
expert users who understand the impact of the configuration changes they
are making should enable it.
Reviewed-by: Ingo Molnar <mingo@elte.hu>
Acked-by: David Woodhouse <david.woodhouse@intel.com>
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: Greg KH <gregkh@suse.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Robin Holt <holt@sgi.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
26-bit ARM support was removed a long time ago, and this symbol has
been defined to be 'y' ever since. As it's never disabled anymore,
we can kill it without any side effects.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Now that all EEPROM drivers live in the same place, let's harmonize
their symbol names.
Also fix eeprom's dependencies, it definitely needs sysfs, and is no
longer experimental after many years in the kernel tree.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: David Brownell <dbrownell@users.sourceforge.net>
The Freecom-FSG3 is a small network-attached-storage device with the
following feature set:
* Intel IXP422
* 4MB Flash (ixp4xx flash driver)
* 64MB RAM
* 4 USB 2.0 host ports (ehci and ohci drivers)
* 1 WAN (eth1) and 3 LAN (eth0) ethernet ports
* Supported by the open source ixp4xx ethernet driver
* Via VT6421 disk controller (libata and sata-via drivers)
* Internal hard disk (PATA supported, SATA not yet supported)
* External SATA port (not yet supported)
* ISL1208 RTC chip
* Winbond 83782 temp sensor and fan controller
* MiniPCI slot
The ixp4xx_defconfig is also updated to support this device (the
leds-fsg driver is to be submitted separately via the leds tree after
this initial support is merged, as it depends on header gpio defines).
Signed-off-by: Rod Whitby <rod@whitby.id.au>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Enables the new ixp4xx qmgr and npe drivers in ixp4xx_defconfig.
Sets up the corresponding platform data for the nslu2 and nas100d
boards, and reads the ethernet MAC address from the internal flash.
Tested on both little-endian and big-endian kernels.
Tested-by: Tom King <tom@websb.net>
Signed-off-by: Rod Whitby <rod@whitby.id.au>
Signed-off-by: Michael Westerhof <mwester@dls.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
These are the only three boards to use the IXP4XX-GPIO-LED driver, and
they can all use the new leds-gpio driver instead with no change in
functionality.
--
Signed-off-by: Rod Whitby <rod@whitby.id.au>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This updates the defconfig for the ixp4xx machine in arch/arm/config
taking all the defaults, with the following additions:
1) Enable support for the nslu2, loft, gateway7001, wg302v2,
dsmg600, and gtwx5715 boards.
2) Enable EABI, OABI, HOTPLUG and FW_LOADER.
3) Enable the RTC subsystem, with drivers for the RTC chips on the
nslu2 (x1205) and nas100d/dsmg600 (pcf8563) boards.
4) Enable the LEDS subsystem to support the nslu2, nas100d and
dsmg600 boards. Enable the ixp4xx beeper driver.
5) Enable the USB subsystem, USB host driver support and USB mass
storage support (required for boot disk on nslu2 board).
6) Enable the ATA subsystem, with drivers for the nas100d/dsmg600
(pata_artop) and avila (ixp4xx_cf) boards.
Signed-off-by: Rod Whitby <rod@whitby.id.au>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add Intel KIXRP435 Reference Platform based on IXP43x processor.
Fixed after review : access to cp15 removed in identification functions,
used access to global processor_id instead
Signed-off-by: Vladimir Barinov <vbarinov@ru.mvista.com>
Signed-off-by: Ruslan Sushko <rsushko@ru.mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
DEBUG_WAITQ appears to have been removed by others, but no one
removed the configuration option from ARM. Remote it from both
Kconfig.debug and all default configurations.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Most ARM defconfigs don't actually need to have PM_LEGACY enabled.
Disable it for ATEB9200, Collie, IXP4xx, OMAP H2, S3C2410 and
Versatile.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Deepak Saxena
Add NAS 100d to machine build list and update to new 2.6.15 options.
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
---
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Deepak Saxena
CONFIG_MACH_GTWX5715 hardcodes the machine type in head-xscale.S so we
can no longer boot on any other machine types. The proper fix would be
to remove the hardcoding, but that machine is an off-the-shelf system
and most users won't have access to the bootloader. :(
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Vincent Sanders
A recent patch which made IXP4xx mach_desc's depend on config options
had the effect of not building the kernel for several machines it
possibly could be, this patch updates the default config to ensure all
possible machines are built for by default.
Signed-off-by: Vincent Sanders <vince@arm.linux.org.uk>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
Krzysztof Kozlowski