Kconfig already allows mpls to be built as module. Following patch
fixes Makefile to do same.
CC: Simon Horman <simon.horman@netronome.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Acked-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mpls gso handler needs to pull skb after segmenting skb.
CC: Simon Horman <simon.horman@netronome.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Acked-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For Renesas USB 3.0 host controller, when unplugging the usb hub which
has the RTL8153 plugged, the driver would get -EPROTO for interrupt
transfer. There is high probability to get the information of "HC died;
cleaning up", if the driver continues to submit the interrupt transfer
before the disconnect() is called.
[ 1024.197678] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.213673] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.229668] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.245661] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.261653] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.277648] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.293642] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.309638] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.325633] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.341627] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.357621] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.373615] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.383097] usb 9-1: USB disconnect, device number 2
[ 1024.383103] usb 9-1.4: USB disconnect, device number 6
[ 1029.391010] xhci_hcd 0000:04:00.0: xHCI host not responding to stop endpoint command.
[ 1029.391016] xhci_hcd 0000:04:00.0: Assuming host is dying, halting host.
[ 1029.392551] xhci_hcd 0000:04:00.0: HC died; cleaning up
[ 1029.421480] usb 8-1: USB disconnect, device number 2
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
netfilter/ipvs fixes for net
The following patchset contains fixes for netfilter/ipvs. This round of
fixes is larger than usual at this stage, specifically because of the
nf_tables bridge reject fixes that I would like to see in 3.18. The
patches are:
1) Fix a null-pointer dereference that may occur when logging
errors. This problem was introduced by 4a4739d56b ("ipvs: Pull
out crosses_local_route_boundary logic") in v3.17-rc5.
2) Update hook mask in nft_reject_bridge so we can also filter out
packets from there. This fixes 36d2af5 ("netfilter: nf_tables: allow
to filter from prerouting and postrouting"), which needs this chunk
to work.
3) Two patches to refactor common code to forge the IPv4 and IPv6
reject packets from the bridge. These are required by the nf_tables
reject bridge fix.
4) Fix nft_reject_bridge by avoiding the use of the IP stack to reject
packets from the bridge. The idea is to forge the reject packets and
inject them to the original port via br_deliver() which is now
exported for that purpose.
5) Restrict nft_reject_bridge to bridge prerouting and input hooks.
the original skbuff may cloned after prerouting when the bridge stack
needs to flood it to several bridge ports, it is too late to reject
the traffic.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Restrict the reject expression to the prerouting and input bridge
hooks. If we allow this to be used from forward or any other later
bridge hook, if the frame is flooded to several ports, we'll end up
sending several reject packets, one per cloned packet.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
If the packet is received via the bridge stack, this cannot reject
packets from the IP stack.
This adds functions to build the reject packet and send it from the
bridge stack. Comments and assumptions on this patch:
1) Validate the IPv4 and IPv6 headers before further processing,
given that the packet comes from the bridge stack, we cannot assume
they are clean. Truncated packets are dropped, we follow similar
approach in the existing iptables match/target extensions that need
to inspect layer 4 headers that is not available. This also includes
packets that are directed to multicast and broadcast ethernet
addresses.
2) br_deliver() is exported to inject the reject packet via
bridge localout -> postrouting. So the approach is similar to what
we already do in the iptables reject target. The reject packet is
sent to the bridge port from which we have received the original
packet.
3) The reject packet is forged based on the original packet. The TTL
is set based on sysctl_ip_default_ttl for IPv4 and per-net
ipv6.devconf_all hoplimit for IPv6.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
That can be reused by the reject bridge expression to build the reject
packet. The new functions are:
* nf_reject_ip6_tcphdr_get(): to sanitize and to obtain the TCP header.
* nf_reject_ip6hdr_put(): to build the IPv6 header.
* nf_reject_ip6_tcphdr_put(): to build the TCP header.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
That can be reused by the reject bridge expression to build the reject
packet. The new functions are:
* nf_reject_ip_tcphdr_get(): to sanitize and to obtain the TCP header.
* nf_reject_iphdr_put(): to build the IPv4 header.
* nf_reject_ip_tcphdr_put(): to build the TCP header.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
These drivers now call ipv6_proxy_select_ident(), which is defined
only if CONFIG_INET is enabled. However, they have really depended
on CONFIG_INET for as long as they have allowed sending GSO packets
from userland.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Fixes: f43798c276 ("tun: Allow GSO using virtio_net_hdr")
Fixes: b9fb9ee07e ("macvtap: add GSO/csum offload support")
Fixes: 5188cd44c5 ("drivers/net, ipv6: Select IPv6 fragment idents for virtio UFO packets")
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings says:
====================
drivers/net,ipv6: Fix IPv6 fragment ID selection for virtio
The virtio net protocol supports UFO but does not provide for passing a
fragment ID for fragmentation of IPv6 packets. We used to generate a
fragment ID wherever such a packet was fragmented, but currently we
always use ID=0!
v2: Add blank lines after declarations
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
UFO is now disabled on all drivers that work with virtio net headers,
but userland may try to send UFO/IPv6 packets anyway. Instead of
sending with ID=0, we should select identifiers on their behalf (as we
used to).
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Fixes: 916e4cf46d ("ipv6: reuse ip6_frag_id from ip6_ufo_append_data")
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv6 does not allow fragmentation by routers, so there is no
fragmentation ID in the fixed header. UFO for IPv6 requires the ID to
be passed separately, but there is no provision for this in the virtio
net protocol.
Until recently our software implementation of UFO/IPv6 generated a new
ID, but this was a bug. Now we will use ID=0 for any UFO/IPv6 packet
passed through a tap, which is even worse.
Unfortunately there is no distinction between UFO/IPv4 and v6
features, so disable UFO on taps and virtio_net completely until we
have a proper solution.
We cannot depend on VM managers respecting the tap feature flags, so
keep accepting UFO packets but log a warning the first time we do
this.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Fixes: 916e4cf46d ("ipv6: reuse ip6_frag_id from ip6_ufo_append_data")
Signed-off-by: David S. Miller <davem@davemloft.net>
Some drivers are unable to perform TX completions in a bound time.
They instead call skb_orphan()
Problem is skb_fclone_busy() has to detect this case, otherwise
we block TCP retransmits and can freeze unlucky tcp sessions on
mostly idle hosts.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Fixes: 1f3279ae0c ("tcp: avoid retransmits of TCP packets hanging in host queues")
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, skb_inner_network_header is used but this does not account
for Ethernet header for ETH_P_TEB. Use skb_inner_mac_header which
handles TEB and also should work with IP encapsulation in which case
inner mac and inner network headers are the same.
Tested: Ran TCP_STREAM over GRE, worked as expected.
Signed-off-by: Tom Herbert <therbert@google.com>
Acked-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Or Gerlitz says:
====================
mlx4 driver encapsulation/steering fixes
The 1st patch fixes a bug in the TX path that supports offloading the
TX checksum of (VXLAN) encapsulated TCP packets. It turns out that the
bug is revealed only when the receiver runs in non-offloaded mode, so
we somehow missed it so far... please queue it for -stable >= 3.14
The 2nd patch makes sure not to leak steering entry on error flow,
please queue it to 3.17-stable
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
If mlx4_ib_create_flow() attempts to create > 1 rules with the
firmware, and one of these registrations fail, we leaked the
already created flow rules.
One example of the leak is when the registration of the VXLAN ghost
steering rule fails, we didn't unregister the original rule requested
by the user, introduced in commit d2fce8a906 "mlx4: Set
user-space raw Ethernet QPs to properly handle VXLAN traffic".
While here, add dump of the VXLAN portion of steering rules
so it can actually be seen when flow creation fails.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For VXLAN/NVGRE encapsulation, the current HW doesn't support offloading
both the outer UDP TX checksum and the inner TCP/UDP TX checksum.
The driver doesn't advertize SKB_GSO_UDP_TUNNEL_CSUM, however we are wrongly
telling the HW to offload the outer UDP checksum for encapsulated packets,
fix that.
Fixes: 837052d0cc ('net/mlx4_en: Add netdev support for TCP/IP
offloads of vxlan tunneling')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2014-10-30
This series contains updates to e1000, igb and ixgbe.
Francesco Ruggeri fixes an issue with e1000 where in a VM the driver did
not support unicast filtering.
Roman Gushchin fixes an issue with igb where the driver was re-using
mapped pages so that packets were still getting dropped even if all
the memory issues are gone and there is free memory.
Junwei Zhang found where in the ixgbe_clean_rx_ring() we were repeating
the assignment of NULL to the receive buffer skb and fixes it.
Emil fixes a race condition between setup_link and SFP detection routine
in the watchdog when setting the advertised speed.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
If we cache them, the kernel will reuse them, independently of
whether forwarding is enabled or not. Which means that if forwarding is
disabled on the input interface where the first routing request comes
from, then that unreachable result will be cached and reused for
other interfaces, even if forwarding is enabled on them. The opposite
is also true.
This can be verified with two interfaces A and B and an output interface
C, where B has forwarding enabled, but not A and trying
ip route get $dst iif A from $src && ip route get $dst iif B from $src
Signed-off-by: Nicolas Cavallari <nicolas.cavallari@green-communications.fr>
Reviewed-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
win0_lock was being used un-initialized, resulting in warning traces
being seen when lock debugging is enabled (and just wrong)
Fixes : fc5ab02096 ('cxgb4: Replaced the backdoor mechanism to access the HW
memory with PCIe Window method')
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hayes Wang says:
====================
r8152: patches for autosuspend
There are unexpected processes when enabling autosuspend.
These patches are used to fix them.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid unnecessary behavior when autosuspend occurs during open().
The relative processes should only be run after finishing open().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If (tp->speed & LINK_STATUS) is not zero, the rtl8152_resume()
would call rtl_start_rx() before enabling the tx/rx. Avoid this
by resetting it to zero.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The flag of SELECTIVE_SUSPEND should be cleared when autoresuming.
Otherwise, when the system suspend and resume occur, it may have
the wrong flow.
Besides, because the flag of SELECTIVE_SUSPEND couldn't be used
to check if the hw enables the relative feature, it should alwayes
be disabled in close().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following commands:
modprobe ixgbe
ifconfig ethX up
ethtool -s ethX advertise 0x020
can lead to "setup link failed with code -14" error due to the setup_link
call racing with the SFP detection routine in the watchdog.
This patch resolves this issue by protecting the setup_link call with check
for __IXGBE_IN_SFP_INIT.
Reported-by: Scott Harrison <scoharr2@cisco.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Martin Zhang <martinbj2008@gmail.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Incoming packet is dropped silently by sk_filter(), if the skb was
allocated from pfmemalloc reserves and the corresponding socket is
not marked with the SOCK_MEMALLOC flag.
Igb driver allocates pages for DMA with __skb_alloc_page(), which
calls alloc_pages_node() with the __GFP_MEMALLOC flag. So, in case
of OOM condition, igb can get pages with pfmemalloc flag set.
If an incoming packet hits the pfmemalloc page and is large enough
(small packets are copying into the memory, allocated with
netdev_alloc_skb_ip_align(), so they are not affected), it will be
dropped.
This behavior is ok under high memory pressure, but the problem is
that the igb driver reuses these mapped pages. So, packets are still
dropping even if all memory issues are gone and there is a plenty
of free memory.
In my case, some TCP sessions hang on a small percentage (< 0.1%)
of machines days after OOMs.
Fix this by avoiding reuse of such pages.
Signed-off-by: Roman Gushchin <klamm@yandex-team.ru>
Tested-by: Aaron Brown "aaron.f.brown@intel.com"
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
VMWare's e1000 implementation does not seem to support unicast filtering.
This can be observed by configuring a macvlan interface on eth0 in a VM in
VMWare Fusion 5.0.5, and trying to use that interface instead of eth0.
Tested on 3.16.
Signed-off-by: Francesco Ruggeri <fruggeri@arista.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The WARN_ON in inet_evict_bucket can be triggered by a valid case:
inet_frag_kill and inet_evict_bucket can be running in parallel on the
same queue which means that there has been at least one more ref added
by a previous inet_frag_find call, but inet_frag_kill can delete the
timer before inet_evict_bucket which will cause the WARN_ON() there to
trigger since we'll have refcnt!=1. Now, this case is valid because the
queue is being "killed" for some reason (removed from the chain list and
its timer deleted) so it will get destroyed in the end by one of the
inet_frag_put() calls which reaches 0 i.e. refcnt is still valid.
CC: Florian Westphal <fw@strlen.de>
CC: Eric Dumazet <eric.dumazet@gmail.com>
CC: Patrick McLean <chutzpah@gentoo.org>
Fixes: b13d3cbfb8 ("inet: frag: move eviction of queues to work queue")
Reported-by: Patrick McLean <chutzpah@gentoo.org>
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the evictor is running it adds some chosen frags to a local list to
be evicted once the chain lock has been released but at the same time
the *frag_queue can be running for some of the same queues and it
may call inet_frag_kill which will wait on the chain lock and
will then delete the queue from the wrong list since it was added in the
eviction one. The fix is simple - check if the queue has the evict flag
set under the chain lock before deleting it, this is safe because the
evict flag is set only under that lock and having the flag set also means
that the queue has been detached from the chain list, so no need to delete
it again.
An important note to make is that we're safe w.r.t refcnt because
inet_frag_kill and inet_evict_bucket will sync on the del_timer operation
where only one of the two can succeed (or if the timer is executing -
none of them), the cases are:
1. inet_frag_kill succeeds in del_timer
- then the timer ref is removed, but inet_evict_bucket will not add
this queue to its expire list but will restart eviction in that chain
2. inet_evict_bucket succeeds in del_timer
- then the timer ref is kept until the evictor "expires" the queue, but
inet_frag_kill will remove the initial ref and will set
INET_FRAG_COMPLETE which will make the frag_expire fn just to remove
its ref.
In the end all of the queue users will do an inet_frag_put and the one
that reaches 0 will free it. The refcount balance should be okay.
CC: Florian Westphal <fw@strlen.de>
CC: Eric Dumazet <eric.dumazet@gmail.com>
CC: Patrick McLean <chutzpah@gentoo.org>
Fixes: b13d3cbfb8 ("inet: frag: move eviction of queues to work queue")
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Reported-by: Patrick McLean <chutzpah@gentoo.org>
Tested-by: Patrick McLean <chutzpah@gentoo.org>
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Reviewed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Remove the rcu_read_lock/unlock around rcu_access_pointer
2. Replace the rcu_dereference with rcu_access_pointer
Signed-off-by: Tej Parkash <tej.parkash@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replaced repetive Device ID's which got added in commit b961f9a488
("cxgb4vf: Remove superfluous "idx" parameter of CH_DEVICE() macro")
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NetworkManager might want to know that it changed when the router advertisement
arrives.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Vijay Subramanian <vijaynsu@cisco.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Olivier Blin says:
====================
cdc-ether: handle promiscuous mode
Since kernel 3.16, my Lenovo USB network adapters (RTL8153) using
cdc-ether are not working anymore in a bridge.
This is due to commit c472ab68ad, which
resets the packet filter when the device is bound.
The default packet filter set by cdc-ether does not include
promiscuous, while the adapter seemed to have promiscuous enabled by
default.
This patch series allows to support promiscuous mode for cdc-ether, by
hooking into set_rx_mode.
Incidentally, maybe this device should be handled by the r8152 driver,
but this patch series is still nice for other adapters.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Oliver Neukum <oneukum@suse.de>
Promiscuous mode was not supported anymore with my Lenovo adapters
(RTL8153) since commit c472ab68ad
(cdc-ether: clean packet filter upon probe).
It was not possible to use them in a bridge anymore.
Signed-off-by: Olivier Blin <olivier.blin@softathome.com>
Also-analyzed-by: Loïc Yhuel <loic.yhuel@softathome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will be used by the set_rx_mode callback.
Also move a comment about multicast filtering in this new function.
Signed-off-by: Olivier Blin <olivier.blin@softathome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To delegate promiscuous mode and multicast filtering to the subdriver.
Signed-off-by: Olivier Blin <olivier.blin@softathome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli says:
====================
net: systemport: RX path and suspend fixes
These two patches fix a race condition where we have our RX interrupts
enabled, but not NAPI for the RX path, and the second patch fixes an
issue for packets stuck in RX fifo during a suspend/resume cycle.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
bcm_sysport_resume() was missing an UniMAC reset which can lead to
various receive FIFO corruptions coming out of a suspend cycle. If the
RX FIFO is stuck, it will deliver corrupted/duplicate packets towards
the host CPU interface.
This could be reproduced on crowded network and when Wake-on-LAN is
enabled for this particular interface because the switch still forwards
packets towards the host CPU interface (SYSTEMPORT), and we had to leave
the UniMAC RX enable bit on to allow matching MagicPackets.
Once we re-enter the resume function, there is a small window during
which the UniMAC receive is still enabled, and we start queueing
packets, but the RDMA and RBUF engines are not ready, which leads to
having packets stuck in the UniMAC RX FIFO, ultimately delivered towards
the host CPU as corrupted.
Fixes: 40755a0fce ("net: systemport: add suspend and resume support")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is currently a small window during which the SYSTEMPORT adapter
enables its RX interrupts without having enabled its NAPI handler, which
can result in packets to be discarded during interface bringup.
A similar but more serious window exists in bcm_sysport_resume() during
which we can have the RDMA engine not fully prepared to receive packets
and yet having RX interrupts enabled.
Fix this my moving the RX interrupt enable down to
bcm_sysport_netif_start() after napi_enable() for the RX path is called,
which fixes both call sites: bcm_sysport_open() and
bcm_sysport_resume().
Fixes: b02e6d9ba7 ("net: systemport: add bcm_sysport_netif_{enable,stop}")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix kernel-doc warning in <linux/skbuff.h> by making both headers_start
and headers_end private fields.
Warning(..//include/linux/skbuff.h:654): No description found for parameter 'headers_end[0]'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marvell phy 88E1145 configuration & initialization was missing a case
for initializing SGMII mode. This patch adds that case.
Signed-off-by: Vince Bridgers <vbridger@opensource.altera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
when slave 0 has no phy and slave 1 connected to phy, driver probe will
fail as there is no phy id present for slave 0 device tree, so continuing
even though no phy-id found, also moving mac-id read later to ensure
mac-id is read from device tree even when phy-id entry in not found.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
pull request: wireless 2014-10-28
Please pull this batch of fixes intended for the 3.18 stream!
For the mac80211 bits, Johannes says:
"Here are a few fixes for the wireless stack: one fixes the
RTS rate, one for a debugfs file, one to return the correct
channel to userspace, a sanity check for a userspace value
and the remaining two are just documentation fixes."
For the iwlwifi bits, Emmanuel says:
"I revert here a patch that caused interoperability issues.
dvm gets a fix for a bug that was reported by many users.
Two minor fixes for BT Coex and platform power fix that helps
reducing latency when the PCIe link goes to low power states."
In addition...
Felix Fietkau adds a couple of ath code fixes related to regulatory
rule enforcement.
Hauke Mehrtens fixes a build break with bcma when CONFIG_OF_ADDRESS
is not set.
Karsten Wiese provides a trio of minor fixes for rtl8192cu.
Kees Cook prevents a potential information leak in rtlwifi.
Larry Finger also brings a trio of minor fixes for rtlwifi.
Rafał Miłecki adds a device ID to the bcma bus driver.
Rickard Strandqvist offers some strn* -> strl* changes in brcmfmac
to eliminate non-terminated string issues.
Sujith Manoharan avoids some ath9k stalls by enabling HW queue control
only for MCC.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn says:
====================
DSA tagging mismatches
The second patch is a fix, which should be applied to -rc. It is
possible to get a DSA configuration which does not work. The patch
stops this happening.
The first patch detects this situation, and errors out the probe of
DSA, making it more obvious something is wrong. It is not required to
apply it -rc.
v2 fixes the use case pointed out by Florian, that a switch driver
may use DSA_TAG_PROTO_NONE which the patch did not correctly handle.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6171 can support two different tagging protocols, DSA and
EDSA. The switch driver structure only allows one protocol to be
enumerated, and DSA was chosen. However the Kconfig entry ensures the
EDSA tagging code is built. With a minimal configuration, we then end
up with a mismatch. The probe is successful, EDSA tagging is used, but
the switch is configured for DSA, resulting in mangled packets.
Change the switch driver structure to enumerate EDSA, fixing the
mismatch.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Fixes: 42f2725394 ("net: DSA: Marvell mv88e6171 switch driver")
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If there is a mismatch between enabled tagging protocols and the
protocol the switch supports, error out, rather than continue with a
situation which is unlikely to work.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
cc: alexander.h.duyck@intel.com
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use daddr instead of reaching into dest.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alex Gartrell <agartrell@fb.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Pravin B Shelar