Babbage is a reference board from Freescale for their i.MX51 SoC.
Add board definition, Kconfig and Makefiles to enable Freescale i.MX51
processor and Babbage board.
Boot tested on a Babbage2.5 board
Signed-off-by: Amit Kucheria <amit.kucheria@canonical.com>
Add basic clock support, cpu identification, I/O mapping, interrupt
controller, serial port and ethernet.
Signed-off-by: Amit Kucheria <amit.kucheria@canonical.com>
Refactor the timer code into version 1 and version 2.
Essentially there are 2 versions of the timer hardware on Freescale MXC
hardware. Version 1 is found on MX1/MXL, MX21 and MX27. Version 2 is found on
MX25, MX31, MX35, MX37, MX51, and future parts.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Amit Kucheria <amit.kucheria@canonical.com>
Freescale i.MX51 processor uses a new interrupt controller. Add
driver for TrustZone Interrupt Controller
Signed-off-by: Amit Kucheria <amit.kucheria@canonical.com>
- The SIC mask is only 2bits wide, not 4
- MX31_OTG_PM_BIT and MX31_H1_PM_BIT use negative logic
- clear MX31_H1_DT_BIT and MX31_H2_DT_BIT so that they can be cleared,
not only set.
- return -EINVAL if called with an invalid controller number
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Daniel Mack <daniel@caiaq.de>
Due to the `ret = gpio_request()' below in the loop, the initial -EINVAL value
of ret is overwritten.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This simplifies the macro and makes is similar to the other
..._IO_ADDRESS macros defined for imx SOCs.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Apart from MXC91231_IO_ADDRESS itself this was the only usage of
MXC91231_AIPS1_IO_ADDRESS. Now MXC91231_IO_ADDRESS can be recoded with
IMX_IO_ADDRESS and all helper macros can go away.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Daniel Schaeffer <daniel.schaeffer@timesys.com>
Cc: Alberto Panizzo <maramaopercheseimorto@gmail.com>
Cc: Ivo Clarysse <ivo.clarysse@gmail.com>
The old names are defined only if the cpp symbol
IMX_NEEDS_DEPRECATED_SYMBOLS exists, which is defined (for now) for all
files below arch/arm/mach-mx1.
This was done earlier for mx2 and mx3, too.
USBD_INT0 is for now defined unconditionally to prevent breaking
drivers/usb/gadget/imx_udc.
While at it use IMX_IO_ADDRESS to define MX1_IO_ADDRESS which
adds a cast to the IO_ADDRESS macro fixing many warnings like
arch/arm/mach-mx1/generic.c:51: warning: passing argument 1 of 'mxc_init_irq' makes pointer from integer without a cast
.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
This fixes:
arch/arm/kernel/debug.S:147: Error: constant expression expected -- `ldrne r3,=(((UART1_BASE_ADDR)-AIPI_BASE_ADDR)+AIPI_BASE_ADDR_VIRT)'
arch/arm/kernel/debug.S:163: Error: constant expression expected -- `ldrne r3,=(((UART1_BASE_ADDR)-AIPI_BASE_ADDR)+AIPI_BASE_ADDR_VIRT)'
when compiling for mx2 with CONFIG_DEBUG_LL=y. A similar error exists
on mx3 and is fixed by this commit, too.
These were introduced by aae7019382.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The fref is needless on mx25 since the reference clock is fixed at 24MHz.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
To distinguish between mx31lite and mx31lilly boards better to use
different enum types.
Signed-off-by: Vladimir Zapolskiy <vzapolskiy@gmail.com>
Acked-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Because of the include of the decompress_inflate.c file from
boot/compress/misc.c, there are different flush() defines:
In file included from arch/arm/boot/compressed/misc.c:249:
arch/arm/boot/compressed/../../../../lib/decompress_inflate.c:138:29: error: macro "flush" passed 2 arguments, but takes just 0
Fix this by removing the define of flush() in misc.c for
CONFIG_DEBUG_ICEDCC as it's already defined in mach/uncompress.h,
and that is being included unconditionally.
Also use a static inline function instead of define
for mach-mxc and mach-gemini to avoid similar bug
for those platforms.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The old driver has the number of SSI units in the system hardcoded,
does not make use of the device model and works only on i.MX21/27.
This driver replaces it. It works in DMA mode on i.MX21/27 and using
an FIQ handler on other systems. It also supports AC97 mode of
the SSI units.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Javier Martin <javier.martin@vista-silicon.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Since AUDMUX configuration appears to be one of the common stumbling
blocks for people setting up i.MX audio try to provide some diagnostic
information describing the current setup to assisist people in working
out what's going on.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This has the addional effect that the macros CSCR_U, CSCR_L and CSCR_A
are not used anymore in mach-pcm038.c and mach-qong.c. These still use
the deprecated IO_ADDRESS macro and shouldn't be used in new code.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Holger Schurig <hs4233@mail.mn-solutions.de>
Cc: Dmitriy Taychenachev <dimichxp@gmail.com>
Some headers have used (now) wrong names or havn't had protection at
all. This is needed before adding static inline functions to the
headers.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Magnus Lilja <lilja.magnus@gmail.com>
Cc: Holger Schurig <hs4233@mail.mn-solutions.de>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Daniel Mack <daniel@caiaq.de>
This include isn't needed and hurts when defining static inline
functions in mach/hardware.h (or files included by mach/hardware.h).
The reason is that the consumers of mach/uncompress.h are compiled using
-Dstatic= so the code for all inline function is included in e.g.
arch/arm/boot/compressed/misc.o.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Jörg Knobloch <knobloch@incostartec.com>
Cc: Alan Carvalho de Assis <acassis@gmail.com>
Cc: Daniel Mack <daniel@caiaq.de>
Cc: Dmitriy Taychenachev <dimichxp@gmail.com>
Define deprecated symbols in an #ifdef IMX_NEEDS_DEPRECATED_SYMBOLS ...
All files that still depend on the old definitions get
-DIMX_NEEDS_DEPRECATED_SYMBOLS passed to the compiler.
When all remaining users are fixed this allows including the soc
specific headers unconditionally.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Eric Benard <eric@eukrea.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Alan Carvalho de Assis <acassis@gmail.com>
Cc: Daniel Mack <daniel@caiaq.de>
Cc: Alberto Panizzo <maramaopercheseimorto@gmail.com>
Cc: Ilya Yanok <yanok@emcraft.com>
Cc: Holger Schurig <hs4233@mail.mn-solutions.de>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Magnus Lilja <lilja.magnus@gmail.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Daniel Mack <daniel@caiaq.de>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Magnus Lilja <lilja.magnus@gmail.com>
The WM8350 core won't actually use the range yet, but it will in
future and the platform data to configure it is there now.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This just leaves cpu.c, devices.c and mm.c to clean up. As these files
are used on more than one SOC they need some more work.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Alberto Panizzo <maramaopercheseimorto@gmail.com>
Cc: Valentin Longchamp <valentin.longchamp@epfl.ch>
Cc: Daniel Mack <daniel@caiaq.de>
Cc: Guennadi Liakhovetski <lg@denx.de>
Cc: Yoichi Yuasa <yuasa@linux-mips.org>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Magnus Lilja <lilja.magnus@gmail.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Harro Haan <hrhaan@yahoo.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Luotao Fu <l.fu@pengutronix.de>
Cc: Ilya Yanok <yanok@emcraft.com>
* git://git.infradead.org/mtd-2.6: (90 commits)
jffs2: Fix long-standing bug with symlink garbage collection.
mtd: OneNAND: Fix test of unsigned in onenand_otp_walk()
mtd: cfi_cmdset_0002, fix lock imbalance
Revert "mtd: move mxcnd_remove to .exit.text"
mtd: m25p80: add support for Macronix MX25L4005A
kmsg_dump: fix build for CONFIG_PRINTK=n
mtd: nandsim: add support for 4KiB pages
mtd: mtdoops: refactor as a kmsg_dumper
mtd: mtdoops: make record size configurable
mtd: mtdoops: limit the maximum mtd partition size
mtd: mtdoops: keep track of used/unused pages in an array
mtd: mtdoops: several minor cleanups
core: Add kernel message dumper to call on oopses and panics
mtd: add ARM pismo support
mtd: pxa3xx_nand: Fix PIO data transfer
mtd: nand: fix multi-chip suspend problem
mtd: add support for switching old SST chips into QRY mode
mtd: fix M29W800D dev_id and uaddr
mtd: don't use PF_MEMALLOC
mtd: Add bad block table overrides to Davinci NAND driver
...
Fixed up conflicts (mostly trivial) in
drivers/mtd/devices/m25p80.c
drivers/mtd/maps/pcmciamtd.c
drivers/mtd/nand/pxa3xx_nand.c
kernel/printk.c
The Freescale MX27 and MX31 SoCs have a EHCI controller onboard.
The controller is capable of USB on the go. This patch adds
a driver to support all three of them.
Users have to pass details about serial interface configuration in the
platform data.
The USB OTG core used here is the ARC core, so the driver should
be renamed and probably be merged with ehci-fsl.c eventually.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch configures iomux and i2c io expander in order to add
support to SD/MMC cards on i-MXT TD60.
Signed-off-by: Alan Carvalho de Assis <acassis@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This is useful for audio where we do not want to setup a new scatterlist
after playing 4GB of audio data. This would cause skips in the playback.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The current model does not allow to put a pad into different modes
once a pins is allocated. Remove the resource handling.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The macro mx31_revision() used to take the global variable system_rev to
determine the CPU revision number. However, this number is expected to
be set by the bootloader and is usually zero (at least on my MX31 based
boards here). More than that, it is usually taken to identify the
board's revision, not the CPU's.
Fix that by reading the the CPU's SREV register instead.
Right now, mx31_read_cpu_rev() is called from mx31_clocks_init() which
is admittedly not a good place for it. However, we need to enable the
IIM clock first, and the clock code also has conditional code that
depends on mx31_revision() returning the right thing.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This commit splits the support code for LogicPD's mx31lite hardware
into module and board specific parts.
This introduces a new mandatory coreparam called 'mx31lite_baseboard'
which specifies the base board support to use. For now, only the LiteKit
development board is supported, and developers of own boards are
encouraged to use that as reference.
The UART support moved to the board code.
Some comments were amended along the way.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
According to Russell King handle_edge_irq is only useful for "edge-based
inputs where the controller does not remember transitions with the input
masked."
So using handle_edge_irq unconditionally for both edge and level irqs is
wrong. Testing showed that the controller does remember transitions
while the interrupt is masked. So use handle_level_irq unconditionally.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The ARC USB OTG Core has support for accessing ULPI tranceivers
through so called ULPI viewports. Export a set of function for use with
the USB OTG framework.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This driver has been tested on i.MX1/i.MX27/i.MX35 with an AT25 type
EEPROM and on i.MX27/i.MX31 with a Freescale MC13783 PMIC.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: David Brownell <david-b@pacbell.net>
Cc: Andrea Paterniani <a.paterniani@swapp-eng.it>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
MBIMX27 is the evaluation board for CPUIMX27 and integrates : a
QVGA TFT, a SPI touchscreen controler, a SDCard connector wired to
SDHC1.
Signed-off-by: Eric Benard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
CPUIMX27 is built around Freescale's i.MX27 and has up to 64MB of
NOR Flash, up to 512MB of NAND Flash and up to 256MB of mDDR,
it includes an ethernet PHY in MII mode, an I2C RTC and a
ST16554 QuadUART on nCS3.
Signed-off-by: Eric Benard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Amit Kucheria