Remove dummy clocks for usb wakeup and add optional ones for
MCU_BUS_CK and DMA_BUS_CK.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This GPIO controller is used on UniPhier SoC family.
The vendor specific property "socionext,interrupt-ranges" is for
specifying interrupt mapping to the parent interrupt controller
because the mapping is not contiguous. It works like "ranges",
but transforms "interrupts" instead of "reg".
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Define two new properties: brcm,rx-aeq-mode which allows configuring the
SATA PHY RX equalizers and when "manual" is used, brcm,rx-aeq can be
used to set the exact value.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This patch adds binding for r8a77995 (R-Car D3). Since r8a77995 doesn't
have dedicated pins (ID, VBUS), this will match against the generic
fallback on R-Car D3.
For now, this driver doesn't support usb role swap for r8a77995.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add USB PHY support for r8a7743/5 SoC. Renesas RZ/G1[ME] (R8A7743/5)
USB PHY is identical to the R-Car Gen2 family.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This adds the binding for describing shared memory used to exchange file
system blocks between the RMTFS client and service. A client for this is
generally found in the modem firmware and is used for accessing
persistent storage for things such as radio calibration.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Example 1 is for "Sampling Rate Conversion",
sample has only 1 CPU, 1 Codec.
Thus, "codec Playback", "DAI1 Playback" route is unnecessary.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add synchronization configuration to STM32 SAI bindings.
This patch also adds peripheral clock which is required
to access synchronization register.
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Johan Hedberg says:
====================
pull request: bluetooth-next 2017-10-19
Here's the first bluetooth-next pull request targeting the 4.15 kernel
release.
- Multiple fixes & improvements to the hci_bcm driver
- DT improvements, e.g. new local-bd-address property
- Fixes & improvements to ECDH usage. Private key is now generated by
the crypto subsystem.
- gcc-4.9 warning fixes
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds the DPAA QBMan support for ARM SoCs and a few minor fixes/updates.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=BpKO
-----END PGP SIGNATURE-----
Merge tag 'soc-fsl-for-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/leo/linux into next/drivers
Pull "FSL/NXP ARM SoC drivers updates for 4.14" from Li Yang:
This adds the DPAA QBMan support for ARM SoCs and a few minor fixes/updates.
This pull request includes updates to the QMAN/BMAN drivers to make
them work on the arm/arm64 architectures in addition to the power
architecture and a few minor update/bug-fix to the soc/fsl drivers.
We got the Reviewed-by from Catalin on the ARM architecture side.
DPAA (Data Path Acceleration Architecture) is a set of hardware
components used on some FSL/NXP QorIQ Networking SoCs, it provides the
infrastructure to support simplified sharing of networking interfaces
and accelerators by multiple CPU cores, and the accelerators
themselves. The QMan(Queue Manager) and BMan(Buffer Manager) are
infrastructural components within the DPAA framework. They are used to
manage queues and buffers for various I/O interfaces, hardware
accelerators.
* tag 'soc-fsl-for-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/leo/linux:
soc/fsl/qbman: Enable FSL_LAYERSCAPE config on ARM
soc/fsl/qbman: Add missing headers on ARM
soc/fsl/qbman: different register offsets on ARM
soc/fsl/qbman: add QMAN_REV32
soc/fsl/qbman: Rework portal mapping calls for ARM/PPC
soc/fsl/qbman: Fix ARM32 typo
soc/fsl/qbman: Drop L1_CACHE_BYTES compile time check
soc/fsl/qbman: Drop set/clear_bits usage
dt-bindings: soc/fsl: Update reserved memory binding for QBMan
soc/fsl/qbman: Use shared-dma-pool for QMan private memory allocations
soc/fsl/qbman: Use shared-dma-pool for BMan private memory allocations
soc/fsl/qbman: Add common routine for QBMan private allocations
soc/fsl/guts: Add compatible string for LS1088
soc/fsl/qman: Sleep instead of stuck hacking jiffies
- add ARC AX10x support,
merged from a separate branch that is also included in the ARC tree
- add Stratix10 support via socfpga
- unify socfpga, stm32, sunxi, and zx2967 into simple-reset driver
- add Meson GX reset level control and remove an unneeded check
- add Uniphier PXs3 and ethernet reset controls
- add MT7622 reset control dt-bindings header
-----BEGIN PGP SIGNATURE-----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=yCoy
-----END PGP SIGNATURE-----
Merge tag 'reset-for-4.15' of git://git.pengutronix.de/git/pza/linux into next/drivers
Pull "Reset controller changes for v4.15" from Philipp Zabel:
- add ARC AX10x support,
merged from a separate branch that is also included in the ARC tree
- add Stratix10 support via socfpga
- unify socfpga, stm32, sunxi, and zx2967 into simple-reset driver
- add Meson GX reset level control and remove an unneeded check
- add Uniphier PXs3 and ethernet reset controls
- add MT7622 reset control dt-bindings header
* tag 'reset-for-4.15' of git://git.pengutronix.de/git/pza/linux:
reset: zx2967: use the reset-simple driver
reset: stm32: use the reset-simple driver
reset: socfpga: use the reset-simple driver
reset: sunxi: use reset-simple driver
reset: add reset-simple to unify socfpga, stm32, sunxi, and zx2967
reset: meson: remove unneeded check in meson_reset_reset
reset: meson: add level reset support for GX SoC family
reset: uniphier: add PXs3 reset data
reset: mediatek: add reset controller dt-bindings required header for MT7622 SoC
reset: socfpga: build the reset-socfpga for Stratix10 SOC
reset: uniphier: add ethernet reset control support
reset: socfpga: fix for 64-bit compilation
ARC: reset: introduce AXS10x reset driver
* Add SCM firmware APIs for download mode and secure IO service
* Add SMEM support for cached entries
* Add SMEM support for global partition, dynamic item limit, and more hosts
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=9wWp
-----END PGP SIGNATURE-----
Merge tag 'qcom-drivers-for-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux into next/drivers
Pull "Qualcomm ARM Based Driver Updates for v4.15" from Andy Gross:
* Add SCM firmware APIs for download mode and secure IO service
* Add SMEM support for cached entries
* Add SMEM support for global partition, dynamic item limit, and more hosts
* tag 'qcom-drivers-for-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux:
firmware: qcom: scm: Expose download-mode control
firmware: qcom: scm: Expose secure IO service
soc: qcom: smem: Increase the number of hosts
soc: qcom: smem: Support dynamic item limit
soc: qcom: smem: Support global partition
soc: qcom: smem: Read version from the smem header
soc: qcom: smem: Use le32_to_cpu for comparison
soc: qcom: smem: Support getting cached entries
soc: qcom: smem: Rename "uncached" accessors
Remove of Exynos4212 related dead code (no more support for this SoC).
-----BEGIN PGP SIGNATURE-----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=7Lj1
-----END PGP SIGNATURE-----
Merge tag 'samsung-drivers-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/drivers
Pull "Samsung soc drivers changes for v4.15" from Krzysztof Kozłowski:
Remove of Exynos4212 related dead code (no more support for this SoC).
* tag 'samsung-drivers-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
soc: samsung: Remove Exynos4212 related dead code
Add basic support for R-Car V3M (R8A77970) SoC.
Sergei Shtylyov says:
* Add support for R-Car V3M (R8A77970) SoC power areas to the R-Car SYSC
driver
* Add support for identifying the R-Car V3M (R8A77970) SoC
* Add support for R-Car V3M (R8A77970) to the R-Car RST driver -- this
driver is needed for the clock driver to work
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=5yPj
-----END PGP SIGNATURE-----
Merge tag 'renesas-drivers-for-v4.15' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/drivers
Pull "Renesas ARM Based SoC Drivers Updates for v4.15" from Simon Horman:
Add basic support for R-Car V3M (R8A77970) SoC.
Sergei Shtylyov says:
* Add support for R-Car V3M (R8A77970) SoC power areas to the R-Car SYSC
driver
* Add support for identifying the R-Car V3M (R8A77970) SoC
* Add support for R-Car V3M (R8A77970) to the R-Car RST driver -- this
driver is needed for the clock driver to work
* tag 'renesas-drivers-for-v4.15' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
soc: renesas: rcar-sysc: add R8A77970 support
soc: renesas: identify R-Car V3M
soc: renesas: rcar-rst: add R8A77970 support
the following:
- Markus adds support for the Broadcom STB DDR PHY frontend which supports
dynamic firmware loading and offers the ability to respond with DRAM refresh
rates. He also adds a proper documentation binding document for that
peripheral
- Brian adds support for S2/S3/S5 system suspend/resume modes on ARM-based SoCs
which is not new but had been lingering for a long time.
- Justin adds S2/S3 system suspend/resume modes on MIPS-based SoCs which is a
bit new newer and builds on top of the ARM-based support.
- Florian adds Device Tree binding documents for both ARM and MIPS based systems
describing the necessary nodes for S2/S3/S5 on these SoCs.
(This pull request somehow missed the 4.14 merge window and is now being sent again
for 4.15 along with build fixes from Arnd).
-----BEGIN PGP SIGNATURE-----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=PnBH
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-4.15/drivers' of http://github.com/Broadcom/stblinux into next/drivers
Pull "Broadcom drivers changes for 4.15" from Florian Fainelli:
This pull requests contains Broadcom SoCs drivers updates for 4.15, please pull
the following:
- Markus adds support for the Broadcom STB DDR PHY frontend which supports
dynamic firmware loading and offers the ability to respond with DRAM refresh
rates. He also adds a proper documentation binding document for that
peripheral
- Brian adds support for S2/S3/S5 system suspend/resume modes on ARM-based SoCs
which is not new but had been lingering for a long time.
- Justin adds S2/S3 system suspend/resume modes on MIPS-based SoCs which is a
bit new newer and builds on top of the ARM-based support.
- Florian adds Device Tree binding documents for both ARM and MIPS based systems
describing the necessary nodes for S2/S3/S5 on these SoCs.
(This pull request somehow missed the 4.14 merge window and is now being sent again
for 4.15 along with build fixes from Arnd).
* tag 'arm-soc/for-4.15/drivers' of http://github.com/Broadcom/stblinux:
soc bcm: brcmstb: Add support for S2/S3/S5 suspend states (MIPS)
dt-bindings: Document MIPS Broadcom STB power management nodes
soc: bcm: brcmstb: Add support for S2/S3/S5 suspend states (ARM)
dt-bindings: ARM: brcmstb: Update Broadcom STB Power Management binding
memory: brcmstb: Add driver for DPFE
dt-bindings: Add bindings for Broadcom STB DRAM Sensors
Correct the USB subnodes in the example, as in f7d569c1e6 ("ARM: dts:
r8a779x: Fix PCI bus dtc warnings").
1. Drop the bogus 'device_type = "pci"' properties,
2. Correct the unit addresses.
Update other bits in the example to match real use:
1. Rename the USB subnodes from "pci" to "usb",
2. Update the "phys" property.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Rob Herring <robh@kernel.org>
The current Amlogic Meson eFuse driver only supports the 64-bit SoCs
(GXBB and newer). Older SoCs cannot be supported by the same driver
because they do not use the meson secure monitor firmware to access the
hardware.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Amlogic Meson6, Meson8 and Meson8b SoCs have an efuse which contains
calibration data from the factory (for the internal temperature sensor
and some CVBS connector settings). Some manufacturers also store the MAC
address or serial number in the efuse.
This documents the devicetree bindings for the efuse on these SoCs.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds the necessary function for handling support on RK3368 SoCs
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Add Audio, HSCIF, I2C, and INTC-EX pin groups on R-Car H3 ES2.0,
- Add Audio and PWM pin groups on R-Car D3,
- Add support for RZ/A1M and RZ/A1L,
- Add INTC-EX pin groups on R-Car M3-W,
- Add SDHI voltage switching on RZ/G1E,
- Make bias control and IOCTRL support more generic,
- Add suspend/resume support for R-Car Gen3,
- Small fixes and cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=6Arb
-----END PGP SIGNATURE-----
Merge tag 'sh-pfc-for-v4.15-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into devel
pinctrl: sh-pfc: Updates for v4.15 (take two)
- Add Audio, HSCIF, I2C, and INTC-EX pin groups on R-Car H3 ES2.0,
- Add Audio and PWM pin groups on R-Car D3,
- Add support for RZ/A1M and RZ/A1L,
- Add INTC-EX pin groups on R-Car M3-W,
- Add SDHI voltage switching on RZ/G1E,
- Make bias control and IOCTRL support more generic,
- Add suspend/resume support for R-Car Gen3,
- Small fixes and cleanups.
Add the Tegra186-specific hypervisor-related register range
properties.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The RZ family of Renesas SoCs has several different subfamilies (RZ/A,
RZ/G, RZ/N, and RZ/T). Clarify that the renesas,rz-cpg-clocks DT
bindings and clk-rz driver apply to RZ/A1 only.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Rob Herring <robh@kernel.org>
Add fallback compatibility strings for R-Car Gen 1 and 2.
In the case of Renesas R-Car hardware we know that there are generations of
SoCs, f.e. Gen 1 and 2. But beyond that its not clear what the relationship
between IP blocks might be. For example, I believe that r8a7790 is older
than r8a7791 but that doesn't imply that the latter is a descendant of the
former or vice versa.
We can, however, by examining the documentation and behaviour of the
hardware at run-time observe that the current driver implementation appears
to be compatible with the IP blocks on SoCs within a given generation.
For the above reasons and convenience when enabling new SoCs a
per-generation fallback compatibility string scheme is being adopted for
drivers for Renesas SoCs.
Note that R-Car Gen2 and RZ/G1 have many compatible IP blocks. The
approach that has been consistently taken for other IP blocks is to name
common code, compatibility strings and so on after R-Car Gen2.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds DT bindings for simple mice attached to GPIO lines. As the
properties are very general and pertains to all mice I can think of, we use
very generic names for the 4-7 GPIO lines, "up", "down" etc.
Acked-by: Hans-Christian Noren Egtvedt <egtvedt@samfundet.no>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
dts files fixed up to contain the necessary data for basic resources, we
can drop the related platform data.
Note that this branch depends on the "omap-for-v4.15/fixes-dt-signed"
branch and the patches with dependencies are based on a merge with that
branch.
These patches first ensure things keep working for the legacy "ti,hwmods"
property when we start making it optional, then adds a minimal TI sysc
interconnect target device driver to handle the new generic "ti,sysc"
compatible property. And then we can finally drop the legacy platform
data for IRQ, DMA and IO resources as seen in the diffstats.
-----BEGIN PGP SIGNATURE-----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=UKzm
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.15/ti-sysc-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/soc
Pull "more soc changes for omaps for v4.15 merge window" from Tony Lindgren:
Drop omap legacy platform data for IRQ, DMA and IO resources. With the
dts files fixed up to contain the necessary data for basic resources, we
can drop the related platform data.
Note that this branch depends on the "omap-for-v4.15/fixes-dt-signed"
branch and the patches with dependencies are based on a merge with that
branch.
These patches first ensure things keep working for the legacy "ti,hwmods"
property when we start making it optional, then adds a minimal TI sysc
interconnect target device driver to handle the new generic "ti,sysc"
compatible property. And then we can finally drop the legacy platform
data for IRQ, DMA and IO resources as seen in the diffstats.
* tag 'omap-for-v4.15/ti-sysc-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (25 commits)
bus: ti-sysc: Fix unbalanced pm_runtime_enable by adding remove
bus: ti-sysc: mark PM functions as __maybe_unused
ARM: OMAP2+: omap_device: fix error return code in omap_device_copy_resources()
ARM: OMAP2+: Drop legacy struct omap_hwmod_addr_space
ARM: OMAP2+: Drop omap_hwmod_dma_info
ARM: OMAP2+: Drop omap_hwmod_irq_info
ARM: OMAP4: Remove legacy IRQ for PRM
ARM: OMAP3: Remove legacy IRQ for PRM
bus: ti-sysc: Add minimal TI sysc interconnect target driver
ARM: OMAP2+: Populate legacy resources for dma and smartreflex
ARM: OMAP2+: Parse module IO range from dts for legacy "ti,hwmods" support
ARM: dts: Configure SmartReflex only to idle the interconnect target module
ARM: dts: Add nodes for missing omap4 interconnect target modules
dt-bindings: bus: Minimal TI sysc interconnect target module binding
ARM: dts: Add missing hwmod related properties for dra7
ARM: dts: Add missing hwmod related nodes for am33xx
ARM: dts: Add missing dma hwmod property for omap5
ARM: dts: Add missing wdt3 node for omap4
ARM: dts: Add missing hsi node for omap4
ARM: dts: Add missing onewire node for omap4
...
Pull "non-urgent device tree fixes for omaps for v4.15 merge window"
from Tony Lindgren
Non-urgent device tree fixes for omaps that can all wait for v4.15
merge window.
Turns out that we have many devices working just because we have
the legacy platform data still around. This is mostly an issue
for omap4, other SoCs just have minimal fixes needed.
As many of the missing device tree nodes and properties are for
devices that have no drivers in the mainline kernel, such as
slimbus, iss, mcasp, aess, fdif and gpu, we might as well start
using the new "ti,sysc" interconnect target module binding for
them so we can get the devices with no child device drivers idled.
This also makes it possible to drop unnecessary platform data
in later patches.
* tag 'omap-for-v4.15/fixes-dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Fix typo for omap4 mcasp rx path
ARM: dts: Configure SmartReflex only to idle the interconnect target module
ARM: dts: Add nodes for missing omap4 interconnect target modules
dt-bindings: bus: Minimal TI sysc interconnect target module binding
ARM: dts: Add missing hwmod related properties for dra7
ARM: dts: Add missing hwmod related nodes for am33xx
ARM: dts: Add missing dma hwmod property for omap5
ARM: dts: Add missing wdt3 node for omap4
ARM: dts: Add missing hsi node for omap4
ARM: dts: Add missing onewire node for omap4
ARM: dts: Add missing smartreflex node and binding for omap4
ARM: dts: Add missing hwmods property for omap4 dma
ARM: dts: Add missing properties for omap4 control modules
ARM: dts: Configure pmu without interrupt for omap4430
ARM: dts: Add missing dma hwmods property for omap3
Pull "Rockchip dts32 updates for 4.15 part1" from Heiko Stübner:
One new board the Vyasa from Amarula Solutions using a rk3288
and core lvds node for the newly added driver+binding.
Also bindings + nodes for the Mali-Utgard GPUs found on some
Rockchip socs like rk3036 and rk3188. With the recently revived
Lima project they can even render a red triangle to a png file.
* tag 'v4.15-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: Enable thermal on rk3288-vyasa board
ARM: dts: rockchip: fix mali400 ppmmu interrupt names
ARM: dts: rockchip: Enable mali GPU node on rk3288-vyasa
ARM: dts: rockchip: enable gpu on rk3188-radxarock
ARM: dts: rockchip: add gpu nodes on rk3066/rk3188
ARM: dts: rockchip: add rk322x gpu node
ARM: dts: rockchip: enable the gpu on rk3036-kylin boards
ARM: dts: rockchip: add rk3036 gpu node
dt-bindings: gpu: mali-utgard: add optional power-domain reference
dt-bindings: gpu: mali-utgard: add optional supply regulator
dt-bindings: gpu: mali-utgard: Add Rockchip Utgard Malis
ARM: dts: rockchip: enable vops and hdmi output on rk3288-vyasa
ARM: dts: rockchip: Add rk3288 vyasa board
dt-bindings: Add vendor prefix for Amarula Solutions
ARM: dts: rockchip: add LVDS node for rk3288
Pull "STM32 DT updates for v4.15, round 1" from Alexandre Torgue:
Highlights:
----------
-Add I2C1 support on STM32F746 SoC
-Enable I2C1 on STM32F746 eval board
-Add Timers support on STM32F746 SoC
-Add USB HS and FS supports on STM32F746 Soc
-Enable USB HS on STM32F746 disco and eval boards
-Enable USB FS en STM32F746 disco board
-Add Vrefbuf to STM32H743 SoC
-Add LPTIMERS support on STM32H743 SoC
-Add DMAMUX support on STM32H743 SoC
-Enable STM32H743 clock driver
-Add MDMA support on STM32H743 SoC
-Change pinctrl pinmux entries for all SoC.
* tag 'stm32-dt-for-v4.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32:
ARM: dts: stm32: Add MDMA support for STM32H743 SoC
ARM: dts: stm32: Enable USB FS on stm32f746-disco
ARM: dts: stm32: Add USB FS support for STM32F746 MCU
ARM: dts: stm32: Enable USB HS on stm32f746-disco
ARM: dts: stm32: Enable USB HS on stm32746g-eval
ARM: dts: stm32: Add USB HS support for STM32F746 MCU
ARM: dts: stm32: change pinctrl bindings definition
ARM: dts: stm32: Enable STM32H743 clock driver
ARM: dts: stm32: fix hse clock frequency on STM32H743 Eval board
ARM: dts: stm32: add Timers driver for stm32f746 MCU
ARM: dts: stm32: Add DMAMUX support for STM32H743 SoC
ARM: dts: stm32: Add lptimer definitions to stm32h743
ARM: dts: stm32: add vrefbuf to stm32h743
ARM: dts: stm32: Add I2C1 support for STM32F746 eval board
ARM: dts: stm32: Add I2C1 support for STM32F746 SoC
Pull "Samsung DTS ARM changes for 4.15" from Krzysztof Kozłowski:
1. Add new board: Hardkernel Odroid HC1.
2. Fix incomplete Odroid-XU3/4 thermal-zones definition leading to
possible overheat if first pair of A7+A15 cores is idle but rest of
CPUs are busy.
3. Add capacity-dmips-mhz properties for CPUs of octa-core SoCs.
4. Add power button to Odroid XU3/4.
5. Improvements in Gscaler, HDMI and Mixer blocks on Exynos5.
6. Add suspend quirk to DWC3 USB controller to fix enumeration of
SuperSpeed devices on Odroid XU4.
7. Add HDMI and MHL to Trats2.
8. Cleanups (redundant properties and nodes).
* tag 'samsung-dt-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
dt-bindings: samsung: Document binding for new Odroid HC1 board
ARM: dts: exynos: Add HDMI and Sil9234 to Trats2 board
ARM: dts: exynos: Add support for Hardkernel's Odroid HC1 board
ARM: dts: exynos: Move audio clocks configuration to odroidxu3-audio.dtsi
ARM: dts: exynos: Add dwc3 SUSPHY quirk
ARM: dts: exynos: Add status property to Exynos 542x Mixer nodes
ARM: dts: exynos: Add status property to Exynos 5250 HDMI and Mixer nodes
ARM: dts: exynos: Cleanup HDMI DCC definitions on Exynos5250 and Exynos542x boards
ARM: dts: exynos: Move HDMI PHY node from boards to exynos5250.dtsi
ARM: dts: exynos: Use specific compatibles for proper Gscaler limits on Exynos5250 and Exynos5420
ARM: dts: exynos: Remove redundant interrupt properties in gpio-keys on Odroid boards
ARM: dts: exynos: Add power button for Odroid XU3/4
ARM: dts: exynos: Remove the display-timing and delay from Rinato
ARM: dts: exynos: add exynos5422 cpu capacity-dmips-mhz information
ARM: dts: exynos: add exynos5420 cpu capacity-dmips-mhz information
ARM: dts: exynos: fix incomplete Odroid-XU3/4 thermal-zones definition
ARM64: DT: Hisilicon SoC DT updates for 4.15
- Add CoreSight related nodes for hi6220
- Add GPIO line names for hikey960
- Rectify the GPIO line names of the Poplar board to keep consistency
- Add thermal sensor binding doc and dt nodes for hi3660
* tag 'hisi-arm64-dt-for-4.15' of git://github.com/hisilicon/linux-hisi:
arm64: dts: Register Hi3660's thermal sensor
dt-bindings: Document the hi3660 thermal sensor binding
arm64: dts: hisilicon: Standardize Poplar GPIO line names
arm64: dts: hikey960: Update HiKey960 with GPIO line names
arm64: dts: hi6220: add coresight dt nodes
Pull "Renesas ARM Based SoC DT Bindings Updates for v4.15" from Simon Horman:
* Consistently do not use ';' in documentation of compat strings
for boards. A misture of using and not using a trailing ';' had
krept in over time with not using being dominant.
* Document bindings for
- Eagle board and r8a77970 (V3M) SoC bindings.
Eagle is a board for the V3M SoC
- Document Kingfisher board bindings.
Kingfisher is an extension board for the H3ULCB and M3ULCB boards.
* Add r8a77970 (V3M) SYSC power domain definitions
Add macros usable by the device tree sources to reference r8a77970 SYSC
power domains by index.
* Add Renesas SoC DT bindings doc to Renesas ARM section of MAINTAINERS file
* Drop bogus node name suffix from example of /renesas,dw-hdmi binding
* Document APMU and SMP enable method for r8a7745 (RZ/G1E) SoC
* tag 'renesas-dt-bindings-for-v4.15' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: remove inconsistent ; from documentation
arm64: renesas: document Eagle board bindings
arm: shmobile: Document Kingfisher board DT bindings
dt-bindings: power: add R8A77970 SYSC power domain definitions
MAINTAINERS: Add Renesas SoC DT bindings doc to Renesas ARM sections
ARM: shmobile: Document R-Car V3M SoC DT bindings
dt-bindings: display: renesas: dw-hdmi: Drop bogus node name suffix
dt-bindings: apmu: Document r8a7745 support
While the new family-specific compatible values introduced by commit
6f54cc1adc ("devicetree: bindings: R-Car Gen2 CMT0 and CMT1
bindings") use the recommended order "<vendor>,<family>-<device>", the
new SoC-specific compatible values still use the old and deprecated
order "<vendor>,<device>-<soc>".
Switch the SoC-specific compatible values to the recommended order while
there are no upstream users of these compatible values yet.
Fixes: 7f03a0ecfd ("devicetree: bindings: r8a73a4 and R-Car Gen2 CMT bindings")
Fixes: 63d9e8ca0d ("devicetree: bindings: Deprecate property, update example")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Many serially-attached GPIO and IIO devices are daisy-chainable.
Examples for GPIO devices are Maxim MAX3191x and TI SN65HVS88x:
https://datasheets.maximintegrated.com/en/ds/MAX31913.pdfhttp://www.ti.com/lit/ds/symlink/sn65hvs880.pdf
Examples for IIO devices are TI DAC128S085 and TI DAC161S055:
http://www.ti.com/lit/ds/symlink/dac128s085.pdfhttp://www.ti.com/lit/ds/symlink/dac161s055.pdf
We already have drivers for daisy-chainable devices in the tree but
their devicetree bindings are somewhat inconsistent and ill-named:
The gpio-74x164.c driver uses "registers-number" to convey the
number of devices in the daisy-chain. (Sans vendor prefix,
multiple vendors sell compatible versions of this chip.)
The gpio-pisosr.c driver takes a different approach and calculates
the number of devices in the daisy-chain by dividing the common
"ngpios" property (Documentation/devicetree/bindings/gpio/gpio.txt)
by 8 (which assumes that each chip has 8 inputs).
Let's standardize on a common "#daisy-chained-devices" property.
That name was chosen because it's the term most frequently used in
datasheets. (A less frequently used synonym is "cascaded devices".)
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some platforms require reset to be released to allow register
access.
Signed-off-by: Alan Tull <atull@kernel.org>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
[Added DT bindings oneliner for standard reset binding]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Renesas R-Car V3M (R8A77970) SoC also has the R-Car gen3 compatible GPIO
controllers, so document the SoC specific bindings.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In Tegra186, the BPMP (Boot and Power Management Processor) implements
an interface that is used to read system temperatures, including CPU
cluster and GPU temperatures. This binding describes the thermal sensor
that is exposed by BPMP.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This commit adds the device tree bindings description for Amlogic's GPIO
interrupt controller available on the meson8b, gxbb and gxl SoC families
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The Socionext Synquacer SoC's implementation of GICv3 has a so-called
'pre-ITS', which maps 32-bit writes targeted at a separate window of
size '4 << device_id_bits' onto writes to GITS_TRANSLATER with device
ID taken from bits [device_id_bits + 1:2] of the window offset.
Writes that target GITS_TRANSLATER directly are reported as originating
from device ID #0.
So add a workaround for this. Given that this breaks isolation, clear
the IRQ_DOMAIN_FLAG_MSI_REMAP flag as well.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Introduce new bindings for the Meson AXG SoC which now have
different memory layout.
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add the initialization of the generic irq chip for the BCM7271 L2
interrupt controller. This controller only supports level
interrupts and uses the "brcm,bcm7271-l2-intc" compatibility
string.
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Document support for the Interrupt Controller for Externel Devices
(INTC-EX) in the Renesas M3-W (r8a7796), V3M (r8a77970), and D3
(r8a77995) SoCs.
No driver update is needed.
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Only exposes a single mode and not a complete display timing, as
the datasheet is rather vague about the minimum/maximum values.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171018172240.8772-1-l.stach@pengutronix.de
This patch adds support for r8a7743/5 SoCs. The Renesas RZ/G1[ME]
(R8A7743/5) usbhs is identical to the R-Car Gen2 family.
No driver change is needed due to the fallback compatible value
"renesas,rcar-gen2-usbhs".
Adding the SoC-specific compatible values here has two purposes:
1. Document which SoCs have this hardware module,
2. Allow checkpatch to validate compatible values.
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Chris Paterson <chris.paterson2@renesas.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Remove optional pinctrls due to using FORCE/RG_IDDIG to implement
manual switch function.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Remove dummy clocks for usb wakeup and add optional ones for
mcu_bus and dma_bus bus.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add a new optional property to disable u3ports
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch adds binding documentation for DWC2 controller in HS mode found
on STMicroelectronics STM32F7xx SoC.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch adds support for generic phy as an optional. If you want
to use a generic phy (e.g. phy-rcar-gen3-usb3 driver) on this driver,
you have to do "insmod phy-rcar-gen3-usb3.ko" first for now.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch adds support for R-Car D3. This SoC needs to release
the PLL reset by the UGCTRL register. So, since this is not the same
as other R-Car Gen3 SoCs, this patch adds a new type as
"USBHS_TYPE_RCAR_GEN3_WITH_PLL".
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch documents the devicetree binding in use for ARM SPE.
Cc: Rob Herring <robh@kernel.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
* commit '3728e6a255b5': (904 commits)
Linux 4.14-rc5
x86/microcode: Do the family check first
locking/lockdep: Disable cross-release features for now
x86/mm: Flush more aggressively in lazy TLB mode
mm, swap: use page-cluster as max window of VMA based swap readahead
mm: page_vma_mapped: ensure pmd is loaded with READ_ONCE outside of lock
kmemleak: clear stale pointers from task stacks
fs/binfmt_misc.c: node could be NULL when evicting inode
fs/mpage.c: fix mpage_writepage() for pages with buffers
linux/kernel.h: add/correct kernel-doc notation
tty: fall back to N_NULL if switching to N_TTY fails during hangup
Revert "vmalloc: back off when the current task is killed"
mm/cma.c: take __GFP_NOWARN into account in cma_alloc()
scripts/kallsyms.c: ignore symbol type 'n'
userfaultfd: selftest: exercise -EEXIST only in background transfer
mm: only display online cpus of the numa node
mm: remove unnecessary WARN_ONCE in page_vma_mapped_walk().
mm/mempolicy: fix NUMA_INTERLEAVE_HIT counter
include/linux/of.h: provide of_n_{addr,size}_cells wrappers for !CONFIG_OF
mm/madvise.c: add description for MADV_WIPEONFORK and MADV_KEEPONFORK
...
R-Car V3M (R8A77970) SoC also has the R-Car gen3 compatible I2C controller,
so document the SoC specific bindings.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add pm-domains property which is required for 66AK2Gx. Also document 66AK2G
unique clocks property usage.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This adds eeprom "size" as optional property for i2c eeproms.
The "size" property allows explicitly specifying the size of the
EEPROM chip in bytes.
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Divagar Mohandass <divagar.mohandass@intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Opal Kelly is a manufacturer of FPGA Integration Modules.
Signed-off-by: Tom McLeod <tom.mcleod@opalkelly.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Cadence QSPI IP has a adapted loop-back circuit which can be enabled by
setting BYPASS field to 0 in READCAPTURE register. It enables use of
QSPI return clock to latch the data rather than the internal QSPI
reference clock. For high speed operations, adapted loop-back circuit
using QSPI return clock helps to increase data valid window.
Add DT parameter cdns,rclk-en to help enable adapted loop-back circuit
for boards which do have QSPI return clock provided. Update binding
documentation for the same.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
Update binding documentation to add a new compatible for TI 66AK2G SoC,
to handle TI SoC specific quirks in the driver.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
The A20 display pipeline has 2 frontends, 2 backends, and 2 TCONs.
This patch adds support (or a compatible string in the frontend's
case) for these components.
The TCONs support directly outputting to CPU/RGB/LVDS LCD panels,
or it can output to HDMI via an on-chip HDMI controller, or
CVBS/YPbPr/VGA signals via on-chip TV encoders. These additional
encoders are not covered in this patch.
Signed-off-by: Jonathan Liu <net147@gmail.com>
[wens@csie.org: Expand commit message]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171017121807.2994-6-wens@csie.org
The A10 display pipeline has 2 frontends, 2 backends, and 2 TCONs.
This patch adds support (or a compatible string in the frontend's
case) for these components.
The TCONs support directly outputting to CPU/RGB/LVDS LCD panels,
or it can output to HDMI via an on-chip HDMI controller, or
CVBS/YPbPr/VGA signals via on-chip TV encoders. These additional
encoders are not covered in this patch.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171017121807.2994-5-wens@csie.org
The HDMI controller in the A10 SoC is the same as the one currently
supported in the A10s. It has slightly different setup parameters.
Since these parameters are not thoroughly understood, we add support
for this variant by copying these parameters verbatim.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171017121807.2994-4-wens@csie.org
The A10 has two TCONs that are similar to the ones found on other SoCs.
Like the A31, TCON0 has a register used to mux the TCON outputs to the
downstream encoders. The bit fields are slightly different.
Signed-off-by: Jonathan Liu <net147@gmail.com>
[wens@csie.org: Reworked for A10 and fixed up commit message]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171017121807.2994-3-wens@csie.org
Most devices do not support lane reordering and in many cases the
documentation of the data-lanes property is incomplete for such devices.
Document that in case the lane reordering isn't supported, monotonically
incremented values from 0 or 1 shall be used.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Port and endpoint numbering has been omitted in DT binding documentation
for a large number of devices. Also common properties the device uses have
been missed in binding documentation. Make it explicit that these things
need to be documented.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Exynos 5250 and 5420 have different hardware rotation limits.
Since we have to distinguish between these two, we add different
compatible: samsung,exynos5250-gsc and samsung,exynos5420-gsc.
Signed-off-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Initially each pin was declared in "include/dt-bindings/stm32<SOC>-pinfunc.h"
and each definition contained SOC names (ex: STM32F429_PA9_FUNC_USART1_TX).
Since this approach was approved, the number of supported MCU has
increased (STM32F429/STM32F469/STM32f746/STM32H743). To avoid to add a new
file in "include/dt-bindings" each time a new STM32 SOC arrives I propose
a new approach which consist to use a macro to define pin muxing in device
tree. All STM32 will use the common macro to define pinmux. Furthermore, it
will make STM32 maintenance and integration of new SOC easier .
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Reviewed-by: Vikas MANOCHA <vikas.manocha@st.com>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Some registers for the Exynos 4412 ISP (Camera subsystem) clocks are
located in the ISP power domain. Because those registers are also
located in a different memory region than the main clock controller,
support for them can be provided by a separate clock controller.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
- Fix unfortunate mistake in the GICv3 ITS binding example
- Two fixes for the recently merged GICv4 support
- GICv3 ITS 52bit PA fixes
- Generic irqchip mask-ack fix, and its application to the tango irqchip
-----BEGIN PGP SIGNATURE-----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=yAAX
-----END PGP SIGNATURE-----
Merge tag 'irqchip-4.14-3' of git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/urgent
Pull irqchip updates for 4.14-rc5 from Marc Zyngier:
- Fix unfortunate mistake in the GICv3 ITS binding example
- Two fixes for the recently merged GICv4 support
- GICv3 ITS 52bit PA fixes
- Generic irqchip mask-ack fix, and its application to the tango irqchip
The A64 is register compatible with the H3, but has a different number
of dma channels and request ports.
Attach additional properties to the node to allow future reuse of the
compatible for controllers with different number of channels/requests.
If dma-requests is not specified, the register layout defined maximum
of 32 is used.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Document a compatible string for the PROBOX2 AVA TV Box.
Cc: support@probox2.com
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Andreas Färber <afaerber@suse.de>
PROBOX2 is a TV box brand by Hong Kong based online reseller W2COMP
Company Limited.
Cc: support@probox2.com
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Andreas Färber <afaerber@suse.de>
* ade7759
- Fix a signed extension bug.
* as3935
- The default noise and watch dog settings were such that the device
was unusuable in most applications. Add device tree parameters to
allow it to be configured to something that will actually work.
* at91-sama5d2 adc
- Fix handling of legacy device trees that don't provide the new
trigger edge property.
* dln2-adc
- Fix a missing Kconfig dependency on IIO_TRIGGERED_BUFFER.
* dummy driver
- Add a missing break so that writing in_voltage0_thresh_rising_en
doesn't always result in an error.
* zpa2326
- Drop a test for an always true condition so that gcc won't spit out
and unused variable warning.
-----BEGIN PGP SIGNATURE-----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=9Vfy
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-4.14b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
Second set of IIO fixes for the 4.14 cycle.
* ade7759
- Fix a signed extension bug.
* as3935
- The default noise and watch dog settings were such that the device
was unusuable in most applications. Add device tree parameters to
allow it to be configured to something that will actually work.
* at91-sama5d2 adc
- Fix handling of legacy device trees that don't provide the new
trigger edge property.
* dln2-adc
- Fix a missing Kconfig dependency on IIO_TRIGGERED_BUFFER.
* dummy driver
- Add a missing break so that writing in_voltage0_thresh_rising_en
doesn't always result in an error.
* zpa2326
- Drop a test for an always true condition so that gcc won't spit out
and unused variable warning.
Signed-off-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Should be in hex, not decimal or even octal
Signed-off-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add vendor prefix for DH electronics GmbH, https://www.dh-electronics.com .
The company is a SoM and evaluation board manufacturer.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Rob Herring <robh@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Use the preferred generic node name in the example.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Rob Herring <robh@kernel.org>
Currently, the examples are using 2MB for the ITS size. Per the
specification (section 8.18 in ARM IHI 0069D), the ITS address map is
128KB.
Update the examples to match the specification.
Signed-off-by: Julien Grall <julien.grall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Add binding document for Broadcom iProc's Multi-Host Bridge (MHB)
block
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add binding document for Broadcom iProc's Chip Device Resource Unit
(CDRU). Multiple iProc based chips have this CDRU block that contains
miscellaneous registers for chip or device configurations. Start with
Stingray specific compatible string for the initial binding
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch adds muic of_compatible in order to use the muic device
driver in device tree.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Use the stock ticker: UBNT as the vendor prefix for Ubiquiti Networks.
Acked-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add a Device Tree binding document for the Broadcom Hurricane 2 SoC
which is an iProc based system.
Acked-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add binding documentation for the Broadcom Hurricane 2 SoCs used in
switching control planes.
Acked-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add support for ls1012a.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Minghuan Lian <minghuan.Lian@nxp.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
In order to aid post-mortem debugging the Qualcomm platforms provide a
"memory download mode", where the boot loader will provide an interface
for custom tools to "download" the content of RAM to a host machine.
The mode is triggered by writing a magic value somewhere in RAM, that is
read in the boot code path after a warm-restart. Two mechanism for
setting this magic value are supported in modern platforms; a direct SCM
call to enable the mode or through a secure io write of a magic value.
In order for a normal reboot not to trigger "download mode" the magic
must be cleared during a clean reboot.
Download mode has to be enabled by including qcom_scm.download_mode=1 on
the command line.
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The Khadas VIM2 is a Single Board Computer, respin of the origin
Khadas VIM board, using an Amlogic S912 SoC and more server oriented.
It provides the same external connectors and header pinout, plus a SPI
NOR Flash, a reprogrammable STM8S003 MCU, FPC Connector, Cooling FAN header
and Pogo Pads Arrays.
Cc: Gouwa <gouwa@szwesion.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This DTS has support for the Fairphone 2 (codenamed FP2).
This first version of the DTS supports just the serial console via the
MSM UART pins.
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The ls1012a implements only 1 MSI controller, and it is the same as
ls1043a.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Minghuan Lian <minghuan.Lian@nxp.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Add DT binding for the HW IR decoder embedded in SMP86xx/SMP87xx.
Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This adds documentation of device tree bindings for the
thermal sensor controller of hi3660 SoC.
Signed-off-by: Kevin Wangtao <kevin.wangtao@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
This adds the compatible string for the mcp23018, which is the i2c variant
of the mcp23s18.
Signed-off-by: Phil Reid <preid@electromag.com.au>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The mcp23s08 driver moved to pinctrl recently. It accepts the
bias-pull-up pinctrl property since then. This updates the binding
doc to reflect that.
Thanks to Sebastian Reichel for the working example.
Signed-off-by: Lars Poeschel <poeschel@lemonage.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The mcp23s08 driver was moved from gpio to pinctrl. This moves it's
devicetree binding doc as well. So driver and binding doc are in sync
again.
Signed-off-by: Lars Poeschel <poeschel@lemonage.de>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The HDMI controller in the A31 SoC is slightly different from the
earlier version. In addition to the TMDS clock and DDC controls,
this version now takes a second DDC clock input.
Add a compatible string for it, and add the DDC clock input to the
list of clocks required.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171010032008.682-7-wens@csie.org
With the recently introduced omap clkctrl module binding, we can start
moving omap hwmod data to device tree and drivers from arch/arm/mach-omap2.
To start doing this, let's introduce a device tree binding for TI
sysc interconnect target module hardware. The sysc manages module clocks,
idlemodes and interconnect level resets. Each interconnect target module
can have one or more child devices connected to it.
TI sysc interconnect target module hardware is independent of the
interconnect. It is used at least with TI L3 interconnect (Arteris NoC)
and TI L4 interconnect (Sonics s3220). The sysc is mostly used for
interaction between module and PRCM. It participates in the OCP Disconnect
Protocol but other than that is mostly indepenent of the interconnect.
As all the features may not be supported for a given sysc module, we
need to use device tree configuration for the revision of the interconnect
target module.
Note that the interconnect target module control registers are always
sprinked at varying locations in the unused address space of the first
child device IP block. To avoid device tree reg conflicts, the sysc device
provides ranges for it's children.
For a non-intrusive transition from static hwmod data to using device
tree defined TI interconnect target module binding, we can keep things
working with static hwmod data if device tree property "ti,hwmods" is
specified for the the interconnect target module.
Note that additional properties for sysc capabilities will be added
later on. For now, we can already use this binding for interconnect
target modules that do not have any child device drivers available.
This allows us to idle the unused interconnect target modules during
init without the need for legacy hwmod platform data for doing it.
Cc: Benoît Cousson <bcousson@baylibre.com>
Cc: Dave Gerlach <d-gerlach@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Nishanth Menon <nm@ti.com>
Cc: Matthijs van Duin <matthijsvanduin@gmail.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Sakari Ailus <sakari.ailus@iki.fi>
Cc: Suman Anna <s-anna@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Describe the binding for firmware-configured instances of the Synopsys
DesignWare PCIe controller in RC mode, that are almost but not quite ECAM
compliant.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Ismail H. Kose <ihkose@gmail.com>
Signed-off-by: Ismail H. Kose <Ismail.Kose@maximintegrated.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Describe how to specify RZ/A1M and RZ/A1L devices.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Support for Exynos4212 SoCs has been removed by commit bca9085e0a ("ARM:
dts: exynos: remove Exynos4212 support (dead code)"), so there is no need
to keep remaining dead code related to this SoC version.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
This patch adds support for r8a7743/5 SoCs. The Renesas RZ/G1[ME]
(R8A7743/5) usbdmac engine is identical to the R-Car Gen2 family.
No driver change is needed due to the fallback compatible value
"renesas,r8a7743-usb-dmac".
Adding the SoC-specific compatible values here has two purposes:
1. Document which SoCs have this hardware module,
2. Allow checkpatch to validate compatible values.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Chris Paterson <chris.paterson2@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch adds documentation of device tree bindings for the STM32 MDMA
controller.
Signed-off-by: M'boumba Cedric Madianga <cedric.madianga@gmail.com>
Signed-off-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
- Fix driver strength selection when selecting hs400es
- Delete bounce buffer handling:
This change fixes a problem related to how bounce buffers are being
allocated. However, instead of trying to fix that, let's just remove
the mmc bounce buffer code altogether, as it has practically no use.
MMC host:
- meson-gx: A couple of fixes related to clock/phase/tuning
- sdhci-xenon: Fix clock resource by adding an optional bus clock
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=0WJ+
-----END PGP SIGNATURE-----
Merge tag 'mmc-v4.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC fixes from Ulf Hansson:
"MMC core:
- Fix driver strength selection when selecting hs400es
- Delete bounce buffer handling:
This change fixes a problem related to how bounce buffers are being
allocated. However, instead of trying to fix that, let's just
remove the mmc bounce buffer code altogether, as it has practically
no use.
MMC host:
- meson-gx: A couple of fixes related to clock/phase/tuning
- sdhci-xenon: Fix clock resource by adding an optional bus clock"
* tag 'mmc-v4.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: sdhci-xenon: Fix clock resource by adding an optional bus clock
mmc: meson-gx: include tx phase in the tuning process
mmc: meson-gx: fix rx phase reset
mmc: meson-gx: make sure the clock is rounded down
mmc: Delete bounce buffer handling
mmc: core: add driver strength selection when selecting hs400es
Document the new pxa3xx_nand driver compatible string for A7k/A8k SoCs
that need to access system controller registers in order to enable the
NAND controller through the use of a phandle pointed to by the
'marvell,system-controller' property.
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
There are three register areas which contain information about the SoC
version and revision:
- the assist registers contain the SoC's "major version" which encodes
the SoC generation and part number. this is available on Meson6,
Meson8 and Meson8b SoCs.
- the bootrom register contains at least the SoCs "misc version". this
is avilable on Meson6, Meson8 and Meson8b
- the analog top registers contain information about the SoC revision.
this is only available on Meson8 and Meson8b
Not much else is currently known about these registers.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add optional local-bd-address property which is a 6-byte array
storing the assigned BD address. Since having a unique BD address
is critical, a per-device property value should be allocated.
This property is usually added by the boot loader which has access
to the provisioned data.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In the same way as Ethernet, gather the Bluetooth related bindings in
one file. Introduce the bluetooth-bd-address property which can be used
to store the assigned BD address.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
SiI9234 transmitter converts eTMDS/HDMI signal to MHL 1.0.
It is controlled via I2C bus. Its interaction with other
devices in video pipeline is performed mainly on HW level.
The only interaction it does on device driver level is
filtering-out unsupported video modes, it exposes drm_bridge
interface to perform this operation.
This patch is based on the code refactored by Tomasz Stanislawski
<t.stanislaws@samsung.com>, which was initially developed by:
Adam Hampson <ahampson@sta.samsung.com>
Erik Gilling <konkers@android.com>
Shankar Bandal <shankar.b@samsung.com>
Dharam Kumar <dharam.kr@samsung.com>
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Acked-by: Rob Herring <robh@kernel.org> [for dt bindings]
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1507212431-5801-2-git-send-email-m.purski@samsung.com
Now that there is documentation for the ds1307 and compatible RTCs, merge
the ds1339 documentation in it.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Rob Herring <robh@kernel.org>
The ST M41T80 family of RTC are not trivial devices, document them.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Add device tree bindings for the SiRFSoC Real Time Clock.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Add device tree bindings for the ST-Ericsson COH 901 331 Real Time Clock
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Rob Herring <robh@kernel.org>
The bindings for the V3 Semiconductor PCI bridge are a tad bit outdated and
predates the more formal format we have adopted for the bindings.
Update them a bit so it is easier to read, and add the Integrator AP-
specific compatible so we can detect that we are running on that specific
platform.
Add a second register bank for the configuration memory area. The device
tree specs do specify a memory range for configuration space but it is not
applicable to custom accessors like this. Instead follow the pattern from
the Versatile PCI adapter and simply add a second register bank for this
memory.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rob Herring <robh@kernel.org>
Cc: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Pull networking fixes from David Miller:
1) Check iwlwifi 9000 reorder buffer out-of-space condition properly,
from Sara Sharon.
2) Fix RCU splat in qualcomm rmnet driver, from Subash Abhinov
Kasiviswanathan.
3) Fix session and tunnel release races in l2tp, from Guillaume Nault
and Sabrina Dubroca.
4) Fix endian bug in sctp_diag_dump(), from Dan Carpenter.
5) Several mlx5 driver fixes from the Mellanox folks (max flow counters
cap check, invalid memory access in IPoIB support, etc.)
6) tun_get_user() should bail if skb->len is zero, from Alexander
Potapenko.
7) Fix RCU lookups in inetpeer, from Eric Dumazet.
8) Fix locking in packet_do_bund().
9) Handle cb->start() error properly in netlink dump code, from Jason
A. Donenfeld.
10) Handle multicast properly in UDP socket early demux code. From Paolo
Abeni.
11) Several erspan bug fixes in ip_gre, from Xin Long.
12) Fix use-after-free in socket filter code, in order to handle the
fact that listener lock is no longer taken during the three-way TCP
handshake. From Eric Dumazet.
13) Fix infoleak in RTM_GETSTATS, from Nikolay Aleksandrov.
14) Fix tail call generation in x86-64 BPF JIT, from Alexei Starovoitov.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (77 commits)
net: 8021q: skip packets if the vlan is down
bpf: fix bpf_tail_call() x64 JIT
net: stmmac: dwmac-rk: Add RK3128 GMAC support
rndis_host: support Novatel Verizon USB730L
net: rtnetlink: fix info leak in RTM_GETSTATS call
socket, bpf: fix possible use after free
mlxsw: spectrum_router: Track RIF of IPIP next hops
mlxsw: spectrum_router: Move VRF refcounting
net: hns3: Fix an error handling path in 'hclge_rss_init_hw()'
net: mvpp2: Fix clock resource by adding an optional bus clock
r8152: add Linksys USB3GIGV1 id
l2tp: fix l2tp_eth module loading
ip_gre: erspan device should keep dst
ip_gre: set tunnel hlen properly in erspan_tunnel_init
ip_gre: check packet length and mtu correctly in erspan_xmit
ip_gre: get key from session_id correctly in erspan_rcv
tipc: use only positive error codes in messages
ppp: fix __percpu annotation
udp: perform source validation for mcast early demux
IPv4: early demux can return an error code
...
XHCI specification 1.1 does not require xHCI-compliant controllers
to always enable hardware USB2 LPM. However, the current xHCI
driver always enable it when seeing HLC=1.
This patch supports an option for users to control disabling
USB2 Hardware LPM via DT/ACPI attribute.
This option is needed in case user would like to disable this
feature. For example, their xHCI controller has its USB2 HW LPM
broken.
Signed-off-by: Tung Nguyen <tunguyen@apm.com>
Signed-off-by: Thang Q. Nguyen <tqnguyen@apm.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add basic reset data for Socionext's new SoC PXs3.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Our first batch of fixes this release cycle, unfortunately a bit noisier
than usual. Two major groups stand out:
- Some pinctril dts/dtsi changes for stm32 due to a new driver being
merged during the merge window, and this aligns the DT contents between
the old format and the new. This could arguably be moved to the next
merge window but it also seemed relatively harmless to include now.
- Amlogic/meson had driver changes merged that required devicetree
changes to avoid functional/performance regressions. I've already
asked them to be more careful about this going forward, and making
sure drivers are compatible with older DTs when they make these kind
of changes. The platform is actively being upstreamed so there's a
few things in flight, we've seen this happen before and sometimes
it's hard to catch in time.
Besides that there is the usual mix of minor fixes.
-----BEGIN PGP SIGNATURE-----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=/0Nj
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Our first batch of fixes this release cycle, unfortunately a bit
noisier than usual. Two major groups stand out:
- Some pinctril dts/dtsi changes for stm32 due to a new driver being
merged during the merge window, and this aligns the DT contents
between the old format and the new. This could arguably be moved to
the next merge window but it also seemed relatively harmless to
include now.
- Amlogic/meson had driver changes merged that required devicetree
changes to avoid functional/performance regressions. I've already
asked them to be more careful about this going forward, and making
sure drivers are compatible with older DTs when they make these
kind of changes. The platform is actively being upstreamed so
there's a few things in flight, we've seen this happen before and
sometimes it's hard to catch in time.
Besides that there is the usual mix of minor fixes"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (33 commits)
ARM: dts: stm32: use right pinctrl compatible for stm32f469
ARM: dts: stm32: Fix STMPE1600 binding on stm32429i-eval board
ARM: defconfig: update Gemini defconfig
ARM: defconfig: FRAMEBUFFER_CONSOLE can no longer be =m
arm64: dts: rockchip: add the grf clk for dw-mipi-dsi on rk3399
reset: Restrict RESET_HSDK to ARC_SOC_HSDK or COMPILE_TEST
ARM: dts: da850-evm: add serial and ethernet aliases
ARM: dts: am43xx-epos-evm: Remove extra CPSW EMAC entry
ARM: dts: am33xx: Add spi alias to match SOC schematics
ARM: OMAP2+: hsmmc: fix logic to call either omap_hsmmc_init or omap_hsmmc_late_init but not both
ARM: dts: dra7: Set a default parent to mcasp3_ahclkx_mux
ARM: OMAP2+: dra7xx: Set OPT_CLKS_IN_RESET flag for gpio1
ARM: dts: nokia n900: drop unneeded/undocumented parts of the dts
arm64: dts: rockchip: Correct MIPI DPHY PLL clock on rk3399
arm64: dt marvell: Fix AP806 system controller size
MAINTAINERS: add Macchiatobin maintainers entry
ARC: reset: remove the misleading v1 suffix all over
ARC: reset: add missing DT binding documentation for HSDKv1 reset driver
ARC: reset: Only build on archs that have IOMEM
ARM: at91: Replace uses of virt_to_phys with __pa_symbol
...
On Armada 7K/8K we need to explicitly enable the bus clock. The bus clock
is optional because not all the SoCs need them but at least for Armada
7K/8K it is actually mandatory.
The binding documentation is updating accordingly.
Without this patch the kernel hand during boot if the mvpp2.2 network
driver was not present in the kernel. Indeed the clock needed by the
xenon controller was set by the network driver.
Fixes: 3a3748dba8 ("mmc: sdhci-xenon: Add Marvell Xenon SDHC core
functionality)"
CC: Stable <stable@vger.kernel.org>
Tested-by: Zhoujie Wu <zjwu@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Documentation bindings for the Low Power General Purpose Register
available on i.MX6 SoCs in the Secure Non-Volatile Storage.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Atmel USART, Freescale UARTs and OMAP UART all support the rs485 binding
described in rs485.txt, this commit just makes that explicit.
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes the extra compatibility string "st,stm32-usart" to
avoid confusion, save some time & space.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Remove misleading HSDK v1 suffix, as there is no v2 planned
- Add missing DT binding documentation for HSDK reset driver
- Fix HSDK reset driver dependencies
-----BEGIN PGP SIGNATURE-----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=Jx/i
-----END PGP SIGNATURE-----
Merge tag 'reset-fixes-for-4.14' of git://git.pengutronix.de/git/pza/linux into fixes
Reset controller fixes for v4.14
- Remove misleading HSDK v1 suffix, as there is no v2 planned
- Add missing DT binding documentation for HSDK reset driver
- Fix HSDK reset driver dependencies
* tag 'reset-fixes-for-4.14' of git://git.pengutronix.de/git/pza/linux:
reset: Restrict RESET_HSDK to ARC_SOC_HSDK or COMPILE_TEST
ARC: reset: remove the misleading v1 suffix all over
ARC: reset: add missing DT binding documentation for HSDKv1 reset driver
ARC: reset: Only build on archs that have IOMEM
Signed-off-by: Olof Johansson <olof@lixom.net>
Add constants and callback functions for the dwmac on rk3128 soc.
As can be seen, the base structure is the same, only registers
and the bits in them moved slightly.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here are a small number (5) of patches for some reported TTY and serial
issues. Nothing major, a documentation update, timing fix, error
handling fix, name reporting fix, and a timeout issue resolved.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWdN+uw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykZmgCbBSJmwcbVhuhZ64Fx4OE0eprjOgoAoMLmHaT2
jTjQTxM/Gaz108t3o9rt
=5ve+
-----END PGP SIGNATURE-----
Merge tag 'tty-4.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are a small number (5) of patches for some reported TTY and
serial issues. Nothing major, a documentation update, timing fix,
error handling fix, name reporting fix, and a timeout issue resolved.
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-4.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: sccnxp: Fix error handling in sccnxp_probe()
tty: serial: lpuart: avoid report NULL interrupt
serial: bcm63xx: fix timing issue.
mxser: fix timeout calculation for low rates
serial: sh-sci: document R8A77970 bindings
Add DT bindings document for Broadcom STB USB PHYs
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJZ0WQ6AAoJEHm+PkMAQRiGuloH/3sF4qfBhPuJo8OTf0uCtQ18
4Ux9zZbm81df/Jjz0exAp1Jqk+TvdIS3OXPWcKilvbUBP16hQcsxFTnI/5QF+YcN
87aNr+OCMJzOBK4suN1yhzO46NYHeIizdB0PTZVL1Zsto69Tt31D8VJmgH6oBxAw
Isb/nAkOr31dZ9PI5UEExTIanUt6EywVb0UswA+2rNl3h1UkeasQCpMpK2n6HBhU
kVD7sxEd/CN0MmfhB0HrySSam/BeSpOtzoU9bemOwrU2uu9+5+2rqMe7Gsdj4nX6
3Kk+7FQNktlrhxCZIFN/+CdusOUuDd8r/75d7DnsRK5YvSb0sZzJkfD3Nba68Ms=
=7J2+
-----END PGP SIGNATURE-----
BackMerge tag 'v4.14-rc3' into drm-next
Linux 4.14-rc3
Requested by Daniel for the tracing build fix in fixes.
Improve the binding example by removing the '@di0' notation, which
fixes the following build warning:
Warning (unit_address_vs_reg): Node /display@di0 has a unit name, but
no reg property
Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
On Armada 7K/8K we need to explicitly enable the bus clock. The bus clock
is optional because not all the SoCs need them but at least for Armada
7K/8K it is actually mandatory.
The binding documentation is updating accordingly.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update omap-ssi binding document to also cover the HSI
compliant module from OMAP4.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Rob Herring <robh@kernel.org>
[dropped the omap.dtsi update and updated patch description accordingly]
Signed-off-by: Sebastian Reichel <sre@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABCAAGBQJZzq0FAAoJEL1qUBy3i3wmiP0P/ihe5tcmm5ckT6PMCqgAlZQU
7JDZCKlBZ/T50/f1luumkQ1rkfBD2KeG7NGjPWo2cmOKynalPkc/k2GJBuFzCrQw
pkl4kpwxdg0EaufNQOFqIBaW14d5kug5upkImlrZNW442xB5/Xmhom8BVO9Uswz6
wEOpq2QFbsxmtMGfbYC7PwmgmudutV0Iv4Eco940QjZd2ce3r0rkf0x8Q5CTYjHx
LyoCDqcS4KA9lc88g8NMpI/NUEZ14hMSsZsMGpmXuvYgA2Mn4rtGNT4SFbOVnDW9
97x7SsxwOJJoC1G1/XbNaRMgJnovAnDl/E7zT3k+ZqtQfXwbl78Jxp6lxB/E6te5
PKmsqyNc0HvwWy7F8CPjnzn6Nuza9J1cMVU1wTWzQxLzTfm3MLs3Fx5bSKjFUe0g
ENYDXzYkxiaD0sgfp8mi8qVLdXiidDkIxSX4LnhY3bKcNW6HfcI407lsb4aOpvBt
Ho5cJWTuVCul4i/j38c0wU1SuYtdCwBOOpOR4FuTjkaCUbFNulHLAFxiKjEzTMSC
NzVGFHpSLisB/AUTXD3F0jYK7XXqvj1NpVlbgjNVwhhPolv4TofxjGdAZ2IxLRSk
p1XoRG4KN5Su1al2DS0m0r7hH4dxdvEsyCP0ylX73B+z3iCsIVedfo7Rihkj9Mi2
oVgdidWdgkotQOrHefVE
=swPa
-----END PGP SIGNATURE-----
Merge tag 'led_fixes-4.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds
Pull LED fixes from Jacek Anaszewski:
"Four fixes for the as3645a LED flash controller and one update to
MAINTAINERS"
* tag 'led_fixes-4.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds:
MAINTAINERS: Add entry for MediaTek PMIC LED driver
as3645a: Unregister indicator LED on device unbind
as3645a: Use integer numbers for parsing LEDs
dt: bindings: as3645a: Use LED number to refer to LEDs
as3645a: Use ams,input-max-microamp as documented in DT bindings
* clk-pm-runtime:
clk: samsung: exynos-audss: Add support for runtime PM
clk: samsung: exynos-audss: Use local variable for controller's device
clk: samsung: exynos5433: Add support for runtime PM
clk: samsung: Add support for runtime PM
clk: Add support for runtime PM
Unit-names must not start with a leading 0.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
UAPI Changes:
Cross-subsystem Changes:
Core Changes:
- DP SDP defines (Ville)
- polish for scdc helpers (Thierry Reding)
- fix lifetimes for connector/plane state across crtc changes (Maarten
Lankhorst).
- sparse fixes (Ville+Thierry)
- make legacy kms ioctls all interruptible (Maarten)
- push edid override into the edid helpers (out of probe helpers)
(Jani)
- DP ESI defines for link status (DK)
Driver Changes:
- drm-panel is now in drm-misc!
- minor panel-simple cleanups/refactoring by various folks
- drm_bridge_add cleanup (Inki Dae)
- constify a few i2c_device_id structs (Arvind Yadav)
- More patches from Noralf's fb/gem helper cleanup
- bridge/synopsis: reset fix (Philippe Cornu)
- fix tracepoint include handling in drivers (Thierry)
- rockchip: lvds support (Sandy Huang)
- move sun4i into drm-misc fold (Maxime Ripard)
- sun4i: refactor driver load + support TCON backend/layer muxing
(Chen-Yu Tsai)
- pl111: support more pl11x variants (Linus Walleij)
- bridge/adv7511: robustify probing/edid handling (Lars-Petersen
Clausen)
New hw support:
- S6E63J0X03 panel (Hoegeun Kwon)
- OTM8009A panel (Philippe CORNU)
- Seiko 43WVF1G panel (Marco Franchi)
- tve200 driver (Linus Walleij)
Plus assorted of tiny patches all over, including our first outreachy
patches from applicants for the winter round!
* tag 'drm-misc-next-2017-09-20' of git://anongit.freedesktop.org/git/drm-misc: (101 commits)
drm: add backwards compatibility support for drm_kms_helper.edid_firmware
drm: handle override and firmware EDID at drm_do_get_edid() level
drm/dp: DPCD register defines for link status within ESI field
drm/rockchip: Replace dev_* with DRM_DEV_*
drm/tinydrm: Drop driver registered message
drm/gem-fb-helper: Use debug message on gem lookup failure
drm/imx: Use drm_gem_fb_create() and drm_gem_fb_prepare_fb()
drm/bridge: adv7511: Constify HDMI CODEC platform data
drm/bridge: adv7511: Enable connector polling when no interrupt is specified
drm/bridge: adv7511: Remove private copy of the EDID
drm/bridge: adv7511: Properly update EDID when no EDID was found
drm/crtc: Convert setcrtc ioctl locking to interruptible.
drm/atomic: Convert pageflip ioctl locking to interruptible.
drm/legacy: Convert setplane ioctl locking to interruptible.
drm/legacy: Convert cursor ioctl locking to interruptible.
drm/atomic: Convert atomic ioctl locking to interruptible.
drm/atomic: Prepare drm_modeset_lock infrastructure for interruptible waiting, v2.
drm/tve200: Clean up panel bridging
drm/doc: Update todo.rst
drm/dp/mst: Sideband message transaction to power up/down nodes
...
STM32 DMA controller has to exposed its number of request line to be
addressed via STM32 DMAMUX.
Signed-off-by: M'boumba Cedric Madianga <cedric.madianga@gmail.com>
Signed-off-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch adds the documentation of device tree bindings for the STM32
DMAMUX.
Signed-off-by: M'boumba Cedric Madianga <cedric.madianga@gmail.com>
Signed-off-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The vendor string for Microcrystal is microcrystal.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
This patch adds device tree bindings for RISC-V CPUs, patterned after
the ARM device tree CPU bindings.
Signed-off-by: Palmer Dabbelt <palmer@dabbelt.com>
Most applications are too noisy to allow the default noise and
watchdog settings, and thus need to be configurable via DT
properties.
Also default settings to POR defaults on a reset, and register
distuber interrupts as noise since it prevents proper usage.
Cc: devicetree@vger.kernel.org
Signed-off-by: Matt Ranostay <matt.ranostay@konsulko.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Document the different nodes required for supporting S2/S3/S5 suspend
states on MIPS-based Broadcom STB SoCs.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Note there is a misc driver drop in here given we have support
in IIO and the feeling is no one will care.
A large part of this series is a boiler plate removal series avoiding
the need to explicitly provide THIS_MODULE in various locations.
It's very dull but touches all drivers.
New device support
* ad5446
- add ids to support compatible parts DAC081S101, DAC101S101,
DAC121S101.
- add the dac7512 id and drop the misc driver as feeling is no
one is using it (was introduced for a board that is long obsolete)
* mt6577
- add bindings for mt2712 which is fully compatible with other
supported parts.
* st_pressure
- add support for LPS33HW and LPS35HW with bindings (ids mostly).
New features
* ccs811
- Add support for the data ready trigger.
* mma8452
- remove artifical restriction on supporting multiple event types
at the same time.
* tcs3472
- support out of threshold events
Core and tree wide cleanup
* Use macro magic to remove the need to provide THIS_MODULE as part of
struct iio_info or struct iio_trigger_ops. This is similar to
work done in a number of other subsystems (e.g. i2c, spi).
All drivers are fixed and then the fields in these structures are
removed.
This will cause build failures for out of tree drivers and any
new drivers that cross with this work going into the kernel.
Note mostly done with a coccinelle patch, included in the series
on the mailing list but not merged as the fields no longer exist
in the structures so the any hold outs will cause a build failure.
Cleanups
* ads1015
- avoid writing config register when it doesn't change.
- add 10% to conversion wait time as it seems it is sometimes
a little small.
* ade7753
- replace use of core mlock with a local lock. This is part of a
long term effort to make the use of mlock opaque and single
purpose.
* ade7759
- expand the use of buf_lock to cover previous mlock cases. This
is a slightly nicer solution to the same issue as in ade7753.
* cros_ec
- drop an unused variable
* inv_mpu6050
- add a missing break in a switch for consistency - not actual
bug,
- make some local arrays static to save on object code size.
* max5481
- drop manual setting of the spi module owner as handled by the
spi core.
* max5487
- drop manual setting of the spi module owner as handled by the
spi core.
* max9611
- drop explicit setting of the i2c module owner as handled by
the i2c core.
* mcp320x
- speed up reads on single channel devices,
- drop unused of_device_id data elements,
- document the struct mcp320x,
- improve binding docs to reflect restrictions on spi setup and
to make it explicit that the reference regulator is needed.
* mma8452
- symbolic to octal permissions,
- unsigned to unsigned int.
* st_lsm6dsx
- avoid setting odr values multiple times,
- drop config of LIR as it is only ever set to the existing
defaults,
- drop rounding configuration as it only ever matches the defaults.
* ti-ads8688
- drop manual setting of the spi module owner as handled by the
spi core.
* tsl2x7x
- constify the i2c_device_id,
- cleanup limit checks to avoid static checker warnings (and generally
have nicer code).
-----BEGIN PGP SIGNATURE-----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=ik5C
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.15a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Round one of new device support, features and cleanup for IIO in the 4.15 cycle.
Note there is a misc driver drop in here given we have support
in IIO and the feeling is no one will care.
A large part of this series is a boiler plate removal series avoiding
the need to explicitly provide THIS_MODULE in various locations.
It's very dull but touches all drivers.
New device support
* ad5446
- add ids to support compatible parts DAC081S101, DAC101S101,
DAC121S101.
- add the dac7512 id and drop the misc driver as feeling is no
one is using it (was introduced for a board that is long obsolete)
* mt6577
- add bindings for mt2712 which is fully compatible with other
supported parts.
* st_pressure
- add support for LPS33HW and LPS35HW with bindings (ids mostly).
New features
* ccs811
- Add support for the data ready trigger.
* mma8452
- remove artifical restriction on supporting multiple event types
at the same time.
* tcs3472
- support out of threshold events
Core and tree wide cleanup
* Use macro magic to remove the need to provide THIS_MODULE as part of
struct iio_info or struct iio_trigger_ops. This is similar to
work done in a number of other subsystems (e.g. i2c, spi).
All drivers are fixed and then the fields in these structures are
removed.
This will cause build failures for out of tree drivers and any
new drivers that cross with this work going into the kernel.
Note mostly done with a coccinelle patch, included in the series
on the mailing list but not merged as the fields no longer exist
in the structures so the any hold outs will cause a build failure.
Cleanups
* ads1015
- avoid writing config register when it doesn't change.
- add 10% to conversion wait time as it seems it is sometimes
a little small.
* ade7753
- replace use of core mlock with a local lock. This is part of a
long term effort to make the use of mlock opaque and single
purpose.
* ade7759
- expand the use of buf_lock to cover previous mlock cases. This
is a slightly nicer solution to the same issue as in ade7753.
* cros_ec
- drop an unused variable
* inv_mpu6050
- add a missing break in a switch for consistency - not actual
bug,
- make some local arrays static to save on object code size.
* max5481
- drop manual setting of the spi module owner as handled by the
spi core.
* max5487
- drop manual setting of the spi module owner as handled by the
spi core.
* max9611
- drop explicit setting of the i2c module owner as handled by
the i2c core.
* mcp320x
- speed up reads on single channel devices,
- drop unused of_device_id data elements,
- document the struct mcp320x,
- improve binding docs to reflect restrictions on spi setup and
to make it explicit that the reference regulator is needed.
* mma8452
- symbolic to octal permissions,
- unsigned to unsigned int.
* st_lsm6dsx
- avoid setting odr values multiple times,
- drop config of LIR as it is only ever set to the existing
defaults,
- drop rounding configuration as it only ever matches the defaults.
* ti-ads8688
- drop manual setting of the spi module owner as handled by the
spi core.
* tsl2x7x
- constify the i2c_device_id,
- cleanup limit checks to avoid static checker warnings (and generally
have nicer code).
Consistently do not suffix compat string documentation with a ';'
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Pull TPM updates from James Morris:
"Here are the TPM updates from Jarkko for v4.14, which I've placed in
their own branch (next-tpm). I ended up cherry-picking them as other
changes had been made in Jarkko's branch after he sent me his original
pull request.
I plan on maintaining a separate branch for TPM (and other security
subsystems) from now on.
From Jarkko: 'Not much this time except a few fixes'"
* 'next-tpm' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
tpm: ibmvtpm: simplify crq initialization and document crq format
tpm: replace msleep() with usleep_range() in TPM 1.2/2.0 generic drivers
Documentation: tpm: add powered-while-suspended binding documentation
tpm: tpm_crb: constify acpi_device_id.
tpm: vtpm: constify vio_device_id
The commit adds mt2712 compatible node in binding document.
Signed-off-by: Zhiyong Tao <zhiyong.tao@mediatek.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
All chips supported by this driver clock data out on the falling edge
and latch data in on the rising edge, hence SPI mode (0,0) or (1,1)
must be used.
Furthermore, none of the chips has an internal reference voltage
regulator, so an external supply is always required and needs to be
specified in the device tree lest the IIO "scale" in sysfs cannot be
calculated.
Document these requirements in the device tree binding, add compatible
strings for the newly supported mcp3550/1/3 and explain that SPI mode
(0,0) should be preferred for these chips.
Cc: Mathias Duckeck <m.duckeck@kunbus.de>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add a new powered-while-suspended property to control the behavior of the
TPM suspend/resume.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Sonny Rao <sonnyrao@chromium.org>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>
Use integers (reg property) to tell the number of the LED to the driver
instead of the node name. While both of these approaches are currently
used by the LED bindings, using integers will require less driver changes
for ACPI support. Additionally, it will make possible LED naming using
chip and LED node names, effectively making the label property most useful
for human-readable names only.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Document the bindings for the cec-gpio module for hardware where the
CEC line and optionally the HPD line are connected to GPIO lines.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Allwinner R40 is a new SoC, with Quad Core Cortex-A7 and peripherals
like A20.
Add support for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The compatible string for Allwinner V3s SoC used to be missing.
Add it to the binding document.
Fixes: b074fede01 ("arm: sunxi: add support for V3s SoC")
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Updates the QMan and BMan device tree bindings for reserved memory
nodes. This makes the reserved memory allocation compatible with
the shared-dma-pool usage.
Signed-off-by: Roy Pledge <roy.pledge@nxp.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Samsung exynos PRNG driver is using crypto framework instead of
hw_random framework. So move the devicetree binding to crypto folder.
Signed-off-by: PrasannaKumar Muralidharan <prasannatsmkumar@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
On some socs Mali Utgard gpus have both soc power-domains and external
supplying regulators, so add an optional power-domains property for
reference.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Rob Herring <robh@kernel.org>
Mali GPUs have a separate supplying regulator in a lot of socs,
so describe a mali-supply property. The already described
operating points will likely also need access to this regulator.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Rob Herring <robh@kernel.org>
Some (older or lower power) Rockchip socs use Utgard-based Mali-GPUs.
So add the necessary compatibles for them. As the setup is the same for
all of them (needing only the additional reset line), they get added in
a somewhat condensed form, to not inflate the document unnecessary.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Rob Herring <robh@kernel.org>
Add binding for the TI's sdhci-omap controller.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This example allocates much more than needed for address regions.
As for "denali_reg", as you see in drivers/mtd/nand/denali.h, all
registers fit in 0x1000.
As for "nand_data", this IP is generally configured to use Indexed
Addressing mode, where there are only two registers in the address
translation module (CTRL: 0x00, DATA: 0x10). Altera SOCFPGA is
also this case. So, 0x20 is enough.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The clock-cell size is 1 on stm32h7 plaform.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Fixes: 3e4d618b07 ("clk: stm32h7: Add stm32h743 clock driver")
Signed-off-by: Rob Herring <robh@kernel.org>
-----BEGIN PGP SIGNATURE-----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=nb+l
-----END PGP SIGNATURE-----
Merge tag 'ib-mfd-many-v4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd into next
Merge "Immutable branch between MFD and many other subsystems due for
the v4.14 merge window" to get the TWL headers moved to the right place.
Document the Eagle device tree bindings, listing it as a supported board.
This allows to use checkpatch.pl to validate .dts files referring to the
Eagle board.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add Kingfisher Device tree bindings Documentation, listing it as a
supported board.
Kingfisher is the H3ULCB/M3ULCB extension board.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Now the audio bindings have their own binding document update the main
MFD document to point to that file and remove the audio binding
documentation.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The chip sst25wf040b and en25s64 are compatible with SPI NOR flash.
Signed-off-by: Yuan Yao <yao.yuan@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add Device Tree binding document for GE Healthcare USB Management
Controller (ACHC).
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Even though the tfa9879 driver can probe via device tree trough the
I2C core code, it is preferable to have explicit device tree
bindings instead [1], so add this support.
[1] https://www.spinics.net/lists/devicetree/msg195176.html
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Łukasz Majewski <lukma@denx.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
On newer imx SOCs accessing OCOTP directly is wrong because the ocotp
clock needs to be enabled first. Add a binding for accessing the same
values through the imx-ocotp nvmem driver using nvmem-cells. This is
similar to other thermal drivers.
The old binding is preserved for compatibility and because it still
works fine on imx6qdl series chips.
In theory this problem could be solved by adding a reference to the
OCOTP clock instead but it is better to hide such details in a specific
nvmem driver.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
On am33xx we're missing the pmu and emif nodes with their related
"ti,hwmods" properties that the SoC interconnect code needs.
Note that this will only show up as a bug with "doesn't have
mpu register target base" boot errors when the legacy platform
data is removed.
Let's also update the related binding documentation while at it.
Cc: Mark Rutland <mark.rutland@arm.com>
Acked-by: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On omap4 we're missing the hsi node with it's related "ti,hwmods"
property that the SoC interconnect code needs.
Note that this will only show up as a bug with "doesn't have
mpu register target base" boot errors when the legacy platform
data is removed.
Let's also update the binding accrodingly while at it.
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Rob Herring <robh+dt@kernel.org>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add Shimafuji Electric, Inc. to the list of device tree vendor
prefixes
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Rob Herring <robh@kernel.org>
We are missing smartreflex device tree nodes for omap4 with
their related "ti,hwmods" properties that the SoC interconnect
code needs.
Note that this will only show up as a bug with "doesn't have
mpu register target base" boot errors when the legacy platform
data is removed.
And since we're missing the device tree binding for smartreflex,
let's also add it and document the existing omap3 use too.
Note that the related driver also needs to be updated to probe
using device tree and get the platform data passed to it using
auxdata with arch/arm/mach-omap2/pdata-quirks.c.
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Tero Kristo <t-kristo@ti.com>
Acked-by: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On omap4, we are missing several ti,hwmods properties and IO
ranges for system control modules. These are needed by the SoC
interconnect code.
Note that this will only show up as a bug with "doesn't have
mpu register target base" boot errors when the legacy platform
data is removed.
In order to add these, we need to move omap4_pmx_wkup to be a
child of omap4_padconf_wkup.
On omap4 there are separate modules for control module and
control module pads. For control module core, we have this
already configured except for the missing ti,hwmods and reg
entries.
Cc: Mark Rutland <mark.rutland@arm.com>
Acked-by: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 446810f2dd ("of: add vendor prefix for Abracon Corporation")
claimed that "abcn" was used as the vendor prefix while in fact "abracon"
was used in the subsequent commits. It is also the only prefix used in the
tree.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
[robh: fix alphabetical order]
Signed-off-by: Rob Herring <robh@kernel.org>
In keeping with the style of the rest of this drivers device tree
bindings split the audio device tree bindings into their own document.
It should be noted this patch makes no change to the binding itself
just moves the documentation into a specific file for the audio
binding. For easy of merging a separate patch removes the current
documentation from the MFD binding documentation.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Armada-37xx UART0 registers are 0x200 bytes wide. Right next to them are
the UART1 registers that should not be declared in this node.
Update the example in DT bindings document accordingly.
Signed-off-by: allen yan <yanwei@marvell.com>
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Add pm-domains property which is required for 66AK2Gx. Also document 66AK2G
unique clocks property usage.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add devicetree binding support for rt5514 spi dsp codec.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Support the function of impedance sensing. It could be set the matrix row
number of the impedance sensing table and the related parameters in the
DTS.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds the binding documentation for Spreadtrum ADI
controller device.
Signed-off-by: Baolin Wang <baolin.wang@spreadtrum.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add R-Car V3M (R8A77970) Clock Pulse Generator / Module Standby and
Software Reset support, using the CPG/MSSR driver core and the common
R-Car Gen3 code.
Based on the original (and large) patch by Daisuke Matsushita
<daisuke.matsushita.ns@hitachi.com>.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add Silicon Storage Technology Inc. to the list of devicetree
vendor prefixes.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Rob Herring <robh@kernel.org>
NutsBoard (http://nutsboard.org/) is an organization and focus
on ARM based embedded boards with open source software.
Signed-off-by: YuanCheng Cheng <onlywig@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Rob Herring <robh@kernel.org>
Use the preferred generic node name in the example.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Rob Herring <robh@kernel.org>
Update the Broadcom STB Power Management binding document with new
compatible strings for the DDR PHY and memory controller found on newer
chips.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Provide bindings for the Broadcom STB DDR PHY Front End (DPFE).
Signed-off-by: Markus Mayer <mmayer@broadcom.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add a new compatible string for the R8A77995 (R-Car D3) RAVB.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
R-Car V3M (R8A77970) SoC also has the R-Car gen3 compatible EtherAVB
device, so document the SoC specific bindings.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
ARC AXS10x boards support custom IP-block which allows to control
reset signals of selected peripherals. For example DW GMAC, etc...
This block is controlled via memory-mapped register (AKA CREG) which
represents up-to 32 reset lines. This regiter is self-clearing so we
don't need to deassert line after reset.
As of today only the following lines are used:
- DW GMAC - line 5
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
R-Car V3M (R8A77970) SoC also has the R-Car gen3 compatible SCIF and HSCIF
ports, so document the SoC specific bindings.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no plan yet to do a v2 board. And even if we were to do it only
some IPs would actually change, so it be best to add suffixes at that
point, not now !
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
When applying the original patch [1], the DT binding docs were lost.
This patch adds them back.
[1] https://patchwork.kernel.org/patch/9852997/
Fixes: e0be864f14 ("ARC: reset: introduce HSDKv1 reset driver")
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Add support for R-Car V3M (R8A77970) SoC power areas to the R-Car SYSC
driver.
Based on the original (and large) patch by Daisuke Matsushita
<daisuke.matsushita.ns@hitachi.com>.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Node names should not use numerical suffixes if the nodes can be
distinguished by unit-address.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Document APMU and SMP enable method for RZ/G1E (also known as
r8a7745) SoC.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add support for R-Car V3M (R8A77970) to the R-Car RST driver -- this driver
is needed for the clock driver to work.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
TBS is a company providing biometrics products and solution in Access
control and time management.
Signed-off-by: Tomas Novotny <tomas@novotny.cz>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This patch adds initial support for rk3288 based
Vyasa board, which is made by Amarula Solutions.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Added 'amarula' as a vendor prefix for Amarula Solutions,
specialist in Embedded and Opensource solutions.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Pull more input updates from Dmitry Torokhov:
"A second round of updates for the input subsystem:
- a new driver for PWM-controlled vibrators
- ucb1400 touchscreen driver had completely busted suspend/resume
handling
- we now handle "home" button found on some devices with Goodix
touchscreens
- assorted other fixups"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: i8042 - add Gigabyte P57 to the keyboard reset table
Input: xpad - validate USB endpoint type during probe
Input: ucb1400_ts - fix suspend and resume handling
Input: edt-ft5x06 - fix access to non-existing register
Input: elantech - make arrays debounce_packet static, reduces object code size
Input: surface3_spi - make const array header static, reduces object code size
Input: goodix - add support for capacitive home button
Input: add a driver for PWM controllable vibrators
Input: adi - make array seq static, reduces object code size
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for 4.14 for MIPS; below a summary of
the non-merge commits:
CM:
- Rename mips_cm_base to mips_gcr_base
- Specify register size when generating accessors
- Use BIT/GENMASK for register fields, order & drop shifts
- Add cluster & block args to mips_cm_lock_other()
CPC:
- Use common CPS accessor generation macros
- Use BIT/GENMASK for register fields, order & drop shifts
- Introduce register modify (set/clear/change) accessors
- Use change_*, set_* & clear_* where appropriate
- Add CM/CPC 3.5 register definitions
- Use GlobalNumber macros rather than magic numbers
- Have asm/mips-cps.h include CM & CPC headers
- Cluster support for topology functions
- Detect CPUs in secondary clusters
CPS:
- Read GIC_VL_IDENT directly, not via irqchip driver
DMA:
- Consolidate coherent and non-coherent dma_alloc code
- Don't use dma_cache_sync to implement fd_cacheflush
FPU emulation / FP assist code:
- Another series of 14 commits fixing corner cases such as NaN
propgagation and other special input values.
- Zero bits 32-63 of the result for a CLASS.D instruction.
- Enhanced statics via debugfs
- Do not use bools for arithmetic. GCC 7.1 moans about this.
- Correct user fault_addr type
Generic MIPS:
- Enhancement of stack backtraces
- Cleanup from non-existing options
- Handle non word sized instructions when examining frame
- Fix detection and decoding of ADDIUSP instruction
- Fix decoding of SWSP16 instruction
- Refactor handling of stack pointer in get_frame_info
- Remove unreachable code from force_fcr31_sig()
- Convert to using %pOF instead of full_name
- Remove the R6000 support.
- Move FP code from *_switch.S to *_fpu.S
- Remove unused ST_OFF from r2300_switch.S
- Allow platform to specify multiple its.S files
- Add #includes to various files to ensure code builds reliable and
without warning..
- Remove __invalidate_kernel_vmap_range
- Remove plat_timer_setup
- Declare various variables & functions static
- Abstract CPU core & VP(E) ID access through accessor functions
- Store core & VP IDs in GlobalNumber-style variable
- Unify checks for sibling CPUs
- Add CPU cluster number accessors
- Prevent direct use of generic_defconfig
- Make CONFIG_MIPS_MT_SMP default y
- Add __ioread64_copy
- Remove unnecessary inclusions of linux/irqchip/mips-gic.h
GIC:
- Introduce asm/mips-gic.h with accessor functions
- Use new GIC accessor functions in mips-gic-timer
- Remove counter access functions from irq-mips-gic.c
- Remove gic_read_local_vp_id() from irq-mips-gic.c
- Simplify shared interrupt pending/mask reads in irq-mips-gic.c
- Simplify gic_local_irq_domain_map() in irq-mips-gic.c
- Drop gic_(re)set_mask() functions in irq-mips-gic.c
- Remove gic_set_polarity(), gic_set_trigger(), gic_set_dual_edge(),
gic_map_to_pin() and gic_map_to_vpe() from irq-mips-gic.c.
- Convert remaining shared reg access, local int mask access and
remaining local reg access to new accessors
- Move GIC_LOCAL_INT_* to asm/mips-gic.h
- Remove GIC_CPU_INT* macros from irq-mips-gic.c
- Move various definitions to the driver
- Remove gic_get_usm_range()
- Remove __gic_irq_dispatch() forward declaration
- Remove gic_init()
- Use mips_gic_present() in place of gic_present and remove
gic_present
- Move gic_get_c0_*_int() to asm/mips-gic.h
- Remove linux/irqchip/mips-gic.h
- Inline __gic_init()
- Inline gic_basic_init()
- Make pcpu_masks a per-cpu variable
- Use pcpu_masks to avoid reading GIC_SH_MASK*
- Clean up mti, reserved-cpu-vectors handling
- Use cpumask_first_and() in gic_set_affinity()
- Let the core set struct irq_common_data affinity
microMIPS:
- Fix microMIPS stack unwinding on big endian systems
MIPS-GIC:
- SYNC after enabling GIC region
NUMA:
- Remove the unused parent_node() macro
R6:
- Constify r2_decoder_tables
- Add accessor & bit definitions for GlobalNumber
SMP:
- Constify smp ops
- Allow boot_secondary SMP op to return errors
VDSO:
- Drop gic_get_usm_range() usage
- Avoid use of linux/irqchip/mips-gic.h
Platform changes:
Alchemy:
- Add devboard machine type to cpuinfo
- update cpu feature overrides
- Threaded carddetect irqs for devboards
AR7:
- allow NULL clock for clk_get_rate
BCM63xx:
- Fix ENETDMA_6345_MAXBURST_REG offset
- Allow NULL clock for clk_get_rate
CI20:
- Enable GPIO and RTC drivers in defconfig
- Add ethernet and fixed-regulator nodes to DTS
Generic platform:
- Move Boston and NI 169445 FIT image source to their own files
- Include asm/bootinfo.h for plat_fdt_relocated()
- Include asm/time.h for get_c0_*_int()
- Include asm/bootinfo.h for plat_fdt_relocated()
- Include asm/time.h for get_c0_*_int()
- Allow filtering enabled boards by requirements
- Don't explicitly disable CONFIG_USB_SUPPORT
- Bump default NR_CPUS to 16
JZ4700:
- Probe the jz4740-rtc driver from devicetree
Lantiq:
- Drop check of boot select from the spi-falcon driver.
- Drop check of boot select from the lantiq-flash MTD driver.
- Access boot cause register in the watchdog driver through regmap
- Add device tree binding documentation for the watchdog driver
- Add docs for the RCU DT bindings.
- Convert the fpi bus driver to a platform_driver
- Remove ltq_reset_cause() and ltq_boot_select(
- Switch to a proper reset driver
- Switch to a new drivers/soc GPHY driver
- Add an USB PHY driver for the Lantiq SoCs using the RCU module
- Use of_platform_default_populate instead of __dt_register_buses
- Enable MFD_SYSCON to be able to use it for the RCU MFD
- Replace ltq_boot_select() with dummy implementation.
Loongson 2F:
- Allow NULL clock for clk_get_rate
Malta:
- Use new GIC accessor functions
NI 169445:
- Add support for NI 169445 board.
- Only include in 32r2el kernels
Octeon:
- Add support for watchdog of 78XX SOCs.
- Add support for watchdog of CN68XX SOCs.
- Expose support for mips32r1, mips32r2 and mips64r1
- Enable more drivers in config file
- Add support for accessing the boot vector.
- Remove old boot vector code from watchdog driver
- Define watchdog registers for 70xx, 73xx, 78xx, F75xx.
- Make CSR functions node aware.
- Allow access to CIU3 IRQ domains.
- Misc cleanups in the watchdog driver
Omega2+:
- New board, add support and defconfig
Pistachio:
- Enable Root FS on NFS in defconfig
Ralink:
- Add Mediatek MT7628A SoC
- Allow NULL clock for clk_get_rate
- Explicitly request exclusive reset control in the pci-mt7620 PCI driver.
SEAD3:
- Only include in 32 bit kernels by default
VoCore:
- Add VoCore as a vendor t0 dt-bindings
- Add defconfig file"
* '4.14-features' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (167 commits)
MIPS: Refactor handling of stack pointer in get_frame_info
MIPS: Stacktrace: Fix microMIPS stack unwinding on big endian systems
MIPS: microMIPS: Fix decoding of swsp16 instruction
MIPS: microMIPS: Fix decoding of addiusp instruction
MIPS: microMIPS: Fix detection of addiusp instruction
MIPS: Handle non word sized instructions when examining frame
MIPS: ralink: allow NULL clock for clk_get_rate
MIPS: Loongson 2F: allow NULL clock for clk_get_rate
MIPS: BCM63XX: allow NULL clock for clk_get_rate
MIPS: AR7: allow NULL clock for clk_get_rate
MIPS: BCM63XX: fix ENETDMA_6345_MAXBURST_REG offset
mips: Save all registers when saving the frame
MIPS: Add DWARF unwinding to assembly
MIPS: Make SAVE_SOME more standard
MIPS: Fix issues in backtraces
MIPS: jz4780: DTS: Probe the jz4740-rtc driver from devicetree
MIPS: Ci20: Enable RTC driver
watchdog: octeon-wdt: Add support for 78XX SOCs.
watchdog: octeon-wdt: Add support for cn68XX SOCs.
watchdog: octeon-wdt: File cleaning.
...
Pull more i2c updates from Wolfram Sang:
"I2C has two more new drivers: Altera FPGA and STM32F7"
* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: i2c-stm32f7: add driver
i2c: i2c-stm32f4: use generic definition of speed enum
dt-bindings: i2c-stm32: Document the STM32F7 I2C bindings
i2c: altera: Add Altera I2C Controller driver
dt-bindings: i2c: Add Altera I2C Controller
Pull watchdog updates from Wim Van Sebroeck:
- add support for the watchdog on Meson8 and Meson8m2
- add support for MediaTek MT7623 and MT7622 SoC
- add support for the r8a77995 wdt
- explicitly request exclusive reset control for asm9260_wdt,
zx2967_wdt, rt2880_wdt and mt7621_wdt
- improvements to asm9260_wdt, aspeed_wdt, renesas_wdt and cadence_wdt
- add support for reading freq via CCF + suspend/resume support for
of_xilinx_wdt
- constify watchdog_ops and various device-id structures
- revert of commit 1fccb73011 ("iTCO_wdt: all versions count down
twice") (Bug 196509)
* git://www.linux-watchdog.org/linux-watchdog: (40 commits)
watchdog: mei_wdt: constify mei_cl_device_id
watchdog: sp805: constify amba_id
watchdog: ziirave: constify i2c_device_id
watchdog: sc1200: constify pnp_device_id
dt-bindings: watchdog: renesas-wdt: Add support for the r8a77995 wdt
watchdog: renesas_wdt: update copyright dates
watchdog: renesas_wdt: make 'clk' a variable local to probe()
watchdog: renesas_wdt: consistently use RuntimePM for clock management
watchdog: aspeed: Support configuration of external signal properties
dt-bindings: watchdog: aspeed: External reset signal properties
drivers/watchdog: Add optional ASPEED device tree properties
drivers/watchdog: ASPEED reference dev tree properties for config
watchdog: da9063_wdt: Simplify by removing unneeded struct...
watchdog: bcm7038: Check the return value from clk_prepare_enable()
watchdog: qcom: Check for platform_get_resource() failure
watchdog: of_xilinx_wdt: Add suspend/resume support
watchdog: of_xilinx_wdt: Add support for reading freq via CCF
dt-bindings: watchdog: mediatek: add support for MediaTek MT7623 and MT7622 SoC
watchdog: max77620_wdt: constify platform_device_id
watchdog: pcwd_usb: constify usb_device_id
...
This patch adds the documentation of device tree bindings for STM32F7 I2C
Signed-off-by: M'boumba Cedric Madianga <cedric.madianga@gmail.com>
Signed-off-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add the documentation to support the Altera synthesizable
logic I2C Controller in FPGA.
Signed-off-by: Thor Thayer <thor.thayer@linux.intel.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
the sunxi-ng framework. Otherwise, the heavy hitters are various drivers
for SoCs like AT91, Amlogic, Renesas, and Rockchip. There are some other
new clk drivers in here too but overall this is just a bunch of clk
drivers for various different pieces of hardware and a collection of
non-critical fixes for clk drivers.
New Drivers:
- Allwinner R40 SoCs
- Renesas R-Car Gen3 USB 2.0 clock selector PHY
- Atmel AT91 audio PLL
- Uniphier PXs3 SoCs
- ARC HSDK Board PLLs
- AXS10X Board PLLs
- STMicroelectronics STM32H743 SoCs
Removed Drivers:
- Non-compiling mb86s7x support
Updates:
- Allwinner A10/A20 SoCs converted to sunxi-ng framework
- Allwinner H3 CPU clk fixes
- Renesas R-Car D3 SoC
- Renesas V2H and M3-W modules
- Samsung Exynos5420/5422/5800 audio fixes
- Rockchip fractional clk approximation fixes
- Rockchip rk3126 SoC support within the rk3128 driver
- Amlogic gxbb CEC32 and sd_emmc clks
- Amlogic meson8b reset controller support
- IDT VersaClock 5P49V5925/5P49V6901 support
- Qualcomm MSM8996 SMMU clks
- Various 'const' applications for struct clk_ops
- si5351 PLL reset bugfix
- Uniphier audio on LD11/LD20 and ethernet support on LD11/LD20/Pro4/PXs2
- Assorted Tegra clk driver fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=0JbT
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"The diff is dominated by the Allwinner A10/A20 SoCs getting converted
to the sunxi-ng framework. Otherwise, the heavy hitters are various
drivers for SoCs like AT91, Amlogic, Renesas, and Rockchip. There are
some other new clk drivers in here too but overall this is just a
bunch of clk drivers for various different pieces of hardware and a
collection of non-critical fixes for clk drivers.
New Drivers:
- Allwinner R40 SoCs
- Renesas R-Car Gen3 USB 2.0 clock selector PHY
- Atmel AT91 audio PLL
- Uniphier PXs3 SoCs
- ARC HSDK Board PLLs
- AXS10X Board PLLs
- STMicroelectronics STM32H743 SoCs
Removed Drivers:
- Non-compiling mb86s7x support
Updates:
- Allwinner A10/A20 SoCs converted to sunxi-ng framework
- Allwinner H3 CPU clk fixes
- Renesas R-Car D3 SoC
- Renesas V2H and M3-W modules
- Samsung Exynos5420/5422/5800 audio fixes
- Rockchip fractional clk approximation fixes
- Rockchip rk3126 SoC support within the rk3128 driver
- Amlogic gxbb CEC32 and sd_emmc clks
- Amlogic meson8b reset controller support
- IDT VersaClock 5P49V5925/5P49V6901 support
- Qualcomm MSM8996 SMMU clks
- Various 'const' applications for struct clk_ops
- si5351 PLL reset bugfix
- Uniphier audio on LD11/LD20 and ethernet support on LD11/LD20/Pro4/PXs2
- Assorted Tegra clk driver fixes"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (120 commits)
clk: si5351: fix PLL reset
ASoC: atmel-classd: remove aclk clock
ASoC: atmel-classd: remove aclk clock from DT binding
clk: at91: clk-generated: make gclk determine audio_pll rate
clk: at91: clk-generated: create function to find best_diff
clk: at91: add audio pll clock drivers
dt-bindings: clk: at91: add audio plls to the compatible list
clk: at91: clk-generated: remove useless divisor loop
clk: mb86s7x: Drop non-building driver
clk: ti: check for null return in strrchr to avoid null dereferencing
clk: Don't write error code into divider register
clk: uniphier: add video input subsystem clock
clk: uniphier: add audio system clock
clk: stm32h7: Add stm32h743 clock driver
clk: gate: expose clk_gate_ops::is_enabled
clk: nxp: clk-lpc32xx: rename clk_gate_is_enabled()
clk: uniphier: add PXs3 clock data
clk: hi6220: change watchdog clock source
clk: Kconfig: Name RK805 in Kconfig for COMMON_CLK_RK808
clk: cs2000: Add cs2000_set_saved_rate
...
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@st.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Pull thermal updates from Zhang Rui:
- fix resources release in error paths when registering thermal zone.
(Christophe Jaillet)
- introduce a new thermal driver for on-chip PVT (Process, Voltage and
Temperature) monitoring unit implemented on UniPhier SoCs. This
driver supports temperature monitoring and alert function. (Kunihiko
Hayashi)
- Add support for mt2712 chip in the mtk_thermal driver. (Louis Yu)
- Add support for RK3328 SOC in rockchip_thermal driver. (Rocky Hao)
- cleanup a couple of platform thermal drivers to constify
thermal_zone_of_device_ops structures. (Julia Lawall)
- a couple of fixes in int340x and intel_pch_thermal thermal driver.
(Arvind Yadav, Sumeet Pawnikar, Brian Bian, Ed Swierk, Zhang Rui)
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux: (27 commits)
Thermal: int3406_thermal: fix thermal sysfs I/F
thermal: mediatek: minor mtk_thermal.c cleanups
thermal: mediatek: extend calibration data for mt2712 chip
thermal: mediatek: add Mediatek thermal driver for mt2712
dt-bindings: thermal: Add binding document for Mediatek thermal controller
thermal: intel_pch_thermal: Fix enable check on Broadwell-DE
thermal: rockchip: Support the RK3328 SOC in thermal driver
dt-bindings: rockchip-thermal: Support the RK3328 SoC compatible
thermal: bcm2835: constify thermal_zone_of_device_ops structures
thermal: exynos: constify thermal_zone_of_device_ops structures
thermal: zx2967: constify thermal_zone_of_device_ops structures
thermal: rcar_gen3_thermal: constify thermal_zone_of_device_ops structures
thermal: qoriq: constify thermal_zone_of_device_ops structures
thermal: hisilicon: constify thermal_zone_of_device_ops structures
thermal: core: Fix resources release in error paths in thermal_zone_device_register()
thermal: core: Use the new 'thermal_zone_destroy_device_groups()' helper function
thermal: core: Add some new helper functions to free resources
thermal: int3400_thermal: process "thermal table changed" event
thermal: uniphier: add UniPhier thermal driver
dt-bindings: thermal: add binding documentation for UniPhier thermal monitor
...
The changes for this release include a new driver for the PWM controller
found on SoCs of the ZTX ZX family. Support for an old SH-Mobile SoC has
been dropped and the Rockchip and MediaTek drivers gain support for more
generations.
Other than that there are a bunch of coding style fixes, minor bug fixes
and cleanup as well as documentation patches.
-----BEGIN PGP SIGNATURE-----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=GUps
-----END PGP SIGNATURE-----
Merge tag 'pwm/for-4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"The changes for this release include a new driver for the PWM
controller found on SoCs of the ZTX ZX family. Support for an old
SH-Mobile SoC has been dropped and the Rockchip and MediaTek drivers
gain support for more generations.
Other than that there are a bunch of coding style fixes, minor bug
fixes and cleanup as well as documentation patches"
* tag 'pwm/for-4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (32 commits)
pwm: pwm-samsung: fix suspend/resume support
pwm: samsung: Remove redundant checks from pwm_samsung_config()
pwm: mediatek: Disable clock on PWM configuration failure
dt-bindings: pwm: Add MT2712/MT7622 information
pwm: mediatek: Fix clock control issue
pwm: mediatek: Fix PWM source clock selection
pwm: mediatek: Fix Kconfig description
pwm: tegra: Explicitly request exclusive reset control
pwm: hibvt: Explicitly request exclusive reset control
pwm: tiehrpwm: Set driver data before runtime PM enable
pwm: tiehrpwm: Miscellaneous coding style fixups
pwm: tiecap: Set driver data before runtime PM enable
pwm: tiecap: Miscellaneous coding style fixups
dt-bindings: pwm: tiecap: Add TI 66AK2G SoC specific compatible
pwm: tiehrpwm: fix clock imbalance in probe error path
pwm: tiehrpwm: Fix runtime PM imbalance at unbind
pwm: Kconfig: Enable pwm-tiecap to be built for Keystone
pwm: Add ZTE ZX PWM device driver
dt-bindings: pwm: Add bindings doc for ZTE ZX PWM controller
pwm: bcm2835: Support for polarity setting via DT
...
As usual, device tree updates is the bulk of our material in this merge
window. This time around, 559 patches affecting both 32- and 64-bit
platforms.
Changes are too many to list individually, but some of the larger ones:
New platform/SoC support:
- Automotive:
+ Renesas R-Car D3 (R8A77995)
+ TI DT76x
+ MediaTek mt2712e
- Communication-oriented:
+ Qualcomm IPQ8074
+ Broadcom Stingray
+ Marvell Armada 8080
- Set top box:
+ Uniphier PXs3
Besides some vendor reference boards for the SoC above, there are also several
new boards/machines:
- TI AM335x Moxa UC-8100-ME-T open platform
- TI AM57xx Beaglebone X15 Rev C
- Microchip/Atmel sama5d27 SoM1 EK
- Broadcom Raspberry Pi Zero W
- Gemini-based D-Link DIR-685 router
- Freescale i.MX6:
+ Toradex Apalis module + Apalis and Ixora carrier boards
+ Engicam GEAM6UL Starter Kit
- Freescale i.MX53-based Beckhoff CX9020 Embedded PC
- Mediatek mt7623-based BananaPi R2
- Several Allwinner-based single-board computers:
+ Cubietruck plus
+ Bananapi M3, M2M and M64
+ NanoPi A64
+ A64-OLinuXino
+ Pine64
- Rockchip RK3328 Pine64/Rock64 board support
- Rockchip RK3399 boards:
+ RK3399 Sapphire module on Excavator carrier (RK3399 reference design)
+ Theobroma Systems RK3399-Q7 SoM
- ZTE ZX296718 PCBOX Board
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=R45j
-----END PGP SIGNATURE-----
Merge tag 'armsoc-devicetree' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM/arm64 Devicetree updates from Olof Johansson:
"As usual, device tree updates is the bulk of our material in this
merge window. This time around, 559 patches affecting both 32- and
64-bit platforms.
Changes are too many to list individually, but some of the larger
ones:
New platform/SoC support:
- Automotive:
+ Renesas R-Car D3 (R8A77995)
+ TI DT76x
+ MediaTek mt2712e
- Communication-oriented:
+ Qualcomm IPQ8074
+ Broadcom Stingray
+ Marvell Armada 8080
- Set top box:
+ Uniphier PXs3
Besides some vendor reference boards for the SoC above, there are also
several new boards/machines:
- TI AM335x Moxa UC-8100-ME-T open platform
- TI AM57xx Beaglebone X15 Rev C
- Microchip/Atmel sama5d27 SoM1 EK
- Broadcom Raspberry Pi Zero W
- Gemini-based D-Link DIR-685 router
- Freescale i.MX6:
+ Toradex Apalis module + Apalis and Ixora carrier boards
+ Engicam GEAM6UL Starter Kit
- Freescale i.MX53-based Beckhoff CX9020 Embedded PC
- Mediatek mt7623-based BananaPi R2
- Several Allwinner-based single-board computers:
+ Cubietruck plus
+ Bananapi M3, M2M and M64
+ NanoPi A64
+ A64-OLinuXino
+ Pine64
- Rockchip RK3328 Pine64/Rock64 board support
- Rockchip RK3399 boards:
+ RK3399 Sapphire module on Excavator carrier (RK3399 reference design)
+ Theobroma Systems RK3399-Q7 SoM
- ZTE ZX296718 PCBOX Board"
* tag 'armsoc-devicetree' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (559 commits)
ARM: dts: at91: at91sam9g45: add AC97
arm64: dts: marvell: mcbin: enable more networking ports
arm64: dts: marvell: add a reference to the sysctrl syscon in the ppv2 node
arm64: dts: marvell: add TX interrupts for PPv2.2
arm64: dts: uniphier: add PXs3 SoC support
ARM: dts: uniphier: add pinctrl groups of ethernet phy mode
ARM: dts: uniphier: fix size of sdctrl nodes
ARM: dts: uniphier: add AIDET nodes
arm64: dts: uniphier: fix size of sdctrl node
arm64: dts: uniphier: add AIDET nodes
Revert "ARM: dts: sun8i: h3: Enable dwmac-sun8i on the Beelink X2"
arm64: dts: uniphier: add reset controller node of analog amplifier
arm64: dts: marvell: add Device Tree files for Armada-8KP
arm64: dts: rockchip: add Haikou baseboard with RK3399-Q7 SoM
arm64: dts: rockchip: add RK3399-Q7 (Puma) SoM
dt-bindings: add rk3399-q7 SoM
ARM: dts: rockchip: enable usb for rv1108-evb
ARM: dts: rockchip: add usb nodes for rv1108 SoCs
dt-bindings: update grf-binding for rv1108 SoCs
ARM: dts: aspeed-g4: fix AHB window size of the SMC controllers
...
This branch contains platform-related driver updates for ARM and ARM64.
Among them:
- Reset driver updates:
+ New API for dealing with arrays of resets
+ Make unimplemented {de,}assert return success on shared resets
+ MSDKv1 driver
+ Removal of obsolete Gemini reset driver
+ Misc updates for sunxi and Uniphier
- SoC drivers:
+ Platform SoC driver registration on Tegra
+ Shuffle of Qualcomm drivers into a submenu
+ Allwinner A64 support for SRAM
+ Renesas R-Car R3 support
+ Power domains for Rockchip RK3366
- Misc updates and smaller fixes for TEE and memory driver subsystems
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJZtdt7AAoJEIwa5zzehBx3EboP/jR2T9lrMavXR1zL48L14yJb
S+fiJlrX1Kr42UF4PQvsfs+uTqOLmycrPVFkMb6IwoUPzQ9UCOSoiMzYm2b7ZPvt
uIesHhdM3/xun6wKfieN8GmNA1yDVynTxo0TTYDw5ha7I6s2GHgw0GSFzy3wm0Qg
KzerAO3gzf3L5XsKR0cai3IXNjHO9ubpFG1ReR09da28nPElP8ggWg0KnqdO76Ch
BGpFj78EC875ZNqwHgnspUqgGDJnBjig3m/uA4FWA0G9Jl38tCyKTZfUR7cEraoV
kyCgBlR/UrI8eXVTyEy5k5iTsQ3A1VhX4rGjyH+5NZHTs1yWr4+RDND/qeGl9tSo
VASuOtH6Rc3vdUDpHPBNAFNQH8fwwDoKf96dvN1tiffsx6LSKb//NyOfkXzKOtR6
CP5raYfX4YktLtHq0XVTZ/6r3XmLcTHzElR/dCFpQOFcTOYii0pWtfcWouahbZ1w
dhoBX/dbNq37MfzrxtHN2VTIEHpn2GU7u+ZGkp2ArokD58BAft/M3Xee1cDnF75g
ZDwe5eNFT8aBZKaY7zwG8cdxiw9kACAivDRwW+zgpfUr39c+d0+QmVfnfJh4EGXK
Ri6yr2EfBWK6jw3cwkdSyyt7iSzIkB+RiuuD1MjpYhWzAvoDpzqkXYukFGbpXnuy
vUFHNuP1ocUsRtCs8mm1
=yBzS
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"This branch contains platform-related driver updates for ARM and ARM64.
Among them:
- Reset driver updates:
+ New API for dealing with arrays of resets
+ Make unimplemented {de,}assert return success on shared resets
+ MSDKv1 driver
+ Removal of obsolete Gemini reset driver
+ Misc updates for sunxi and Uniphier
- SoC drivers:
+ Platform SoC driver registration on Tegra
+ Shuffle of Qualcomm drivers into a submenu
+ Allwinner A64 support for SRAM
+ Renesas R-Car R3 support
+ Power domains for Rockchip RK3366
- Misc updates and smaller fixes for TEE and memory driver
subsystems"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (54 commits)
firmware: arm_scpi: fix endianness of dev_id in struct dev_pstate_set
soc/tegra: fuse: Add missing semi-colon
soc/tegra: Restrict SoC device registration to Tegra
drivers: soc: sunxi: add support for A64 and its SRAM C
drivers: soc: sunxi: add support for remapping func value to reg value
drivers: soc: sunxi: fix error processing on base address when claiming
dt-bindings: add binding for Allwinner A64 SRAM controller and SRAM C
bus: sunxi-rsb: Enable by default for ARM64
soc/tegra: Register SoC device
firmware: tegra: set drvdata earlier
memory: Convert to using %pOF instead of full_name
soc: Convert to using %pOF instead of full_name
bus: Convert to using %pOF instead of full_name
firmware: Convert to using %pOF instead of full_name
soc: mediatek: add SCPSYS power domain driver for MediaTek MT7622 SoC
soc: mediatek: add header files required for MT7622 SCPSYS dt-binding
soc: mediatek: reduce code duplication of scpsys_probe across all SoCs
dt-bindings: soc: update the binding document for SCPSYS on MediaTek MT7622 SoC
reset: uniphier: add analog amplifiers reset control
reset: uniphier: add video input subsystem reset control
...
This branch contains platform updates for 32- and 64-bit ARM,
including defconfig updates to enable new options, drivers and
platforms. There are also a few fixes and cleanups for some existing vendors.
Some of the things worth highlighting here are:
- Enabling new crypt drivers on arm64 defconfig
- QCOM IPQ8074 clocks and pinctrl drivers on arm64 defconfig
- Debug support enabled for Renesas r8a7743
- Various config updates for Renesas platforms (sound, USB, other drivers)
- Platform support (including SMP) for TI dra762
- OMAP cleanups: Move to use generic 8250 debug_ll, removal of stale DMA code
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJZtdXjAAoJEIwa5zzehBx3ExIQAJQ6anSZlkGysXqptA4c1HuL
vgGq/U5xZ1Wa4Z/YX7//wuCMwRClc1j/zSJ5PP+wP0YsaviN7iF/8H1P/HQtCiTT
DcEQPSI770829wzW4oMNW0PyU/ZnWMtuiMB+FAjdPVjbS8bT4PIK72D8PYKrT7f8
8bU51+QezjSLamQaA8S2RyX+kYI/4znTa/9Aco4AlCtioV8h9gQanFYd2EI/EMhU
1uvR3xUFf/YK49+M5J6m3DvtFffllHU9TKV/EAQD1Bhl1s5VPfem+a8JbVh1m7M+
NzQOOoPJ9jYOGfjlaQQVmZ/1E4iKac1oK4x44Djk/i+RFjl+AT/2co3RcaEq9Npw
5HNsK8ujnjzWB3xHu5wK5CbrjLNYco9hOpJaGkSeClo4ElDJVSKxyqWkZuhhnSA8
bXXV5VraMX67tjG7Ou8+NtdbMkGdOUqnNbuBlCxkxpWxhtaUQG1YHHQDofUXNguy
rtVhKRZRSkNYrp4lDCKCXVFFO077FGzP2Boq6JVzLv+U1l6JlZkkr3EWKYMY45HC
o2rVcAB4lMR/k6tqE5MAmQC53jCNlFZt2xtf1WRVKf+0TfBVIGX3MxvFxl4E9wA+
9pdJ9ujZWsPjTcZcktA6AsaK7uevRxcB2YZYv4pXVjR1RcZ/SfiEf4UW+md3j4QB
igKej5WsRiCPwnkMFKs0
=g8cF
-----END PGP SIGNATURE-----
Merge tag 'armsoc-platforms' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM/arm64 SoC platform updates from Olof Johansson: "This branch
contains platform updates for 32- and 64-bit ARM, including defconfig
updates to enable new options, drivers and platforms. There are also a
few fixes and cleanups for some existing vendors.
Some of the things worth highlighting here are:
- Enabling new crypt drivers on arm64 defconfig
- QCOM IPQ8074 clocks and pinctrl drivers on arm64 defconfig
- Debug support enabled for Renesas r8a7743
- Various config updates for Renesas platforms (sound, USB, other
drivers)
- Platform support (including SMP) for TI dra762
- OMAP cleanups: Move to use generic 8250 debug_ll, removal of stale
DMA code"
* tag 'armsoc-platforms' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (109 commits)
ARM: multi_v7_defconfig: make eSDHC driver built-in
arm64: defconfig: enable rockchip graphics
MAINTAINERS: Update Cavium ThunderX2 entry
ARM: config: aspeed: Add I2C, VUART, LPC Snoop
ARM: configs: aspeed: Update Aspeed G4 with VMSPLIT_2G
ARM: s3c24xx: Fix NAND ECC mode for mini2440 board
ARM: davinci_all_defconfig: enable tinydrm and ST7586
arm64: defconfig: Enable QCOM IPQ8074 clock and pinctrl
ARM: defconfig: tegra: Enable ChipIdea UDC driver
ARM: configs: Add Tegra I2S interfaces to multi_v7_defconfig
ARM: tegra: Add Tegra I2S interfaces to defconfig
ARM: tegra: Update default configuration for v4.13-rc1
MAINTAINERS: update ARM/ZTE entry
soc: versatile: remove unnecessary static in realview_soc_probe()
ARM: Convert to using %pOF instead of full_name
ARM: hisi: Fix typo in comment
ARM: multi_v7_defconfig: add CONFIG_BRCMSTB_THERMAL
arm64: defconfig: add CONFIG_BRCMSTB_THERMAL
arm64: defconfig: add recently added crypto drivers as modules
arm64: defconfig: enable CONFIG_UNIPHIER_WATCHDOG
...
Slightly more changes than usual this time:
- KDump Kernel IOMMU take-over code for AMD IOMMU. The code now
tries to preserve the mappings of the kernel so that master
aborts for devices are avoided. Master aborts cause some
devices to fail in the kdump kernel, so this code makes the
dump more likely to succeed when AMD IOMMU is enabled.
- Common flush queue implementation for IOVA code users. The
code is still optional, but AMD and Intel IOMMU drivers had
their own implementation which is now unified.
- Finish support for iommu-groups. All drivers implement this
feature now so that IOMMU core code can rely on it.
- Finish support for 'struct iommu_device' in iommu drivers. All
drivers now use the interface.
- New functions in the IOMMU-API for explicit IO/TLB flushing.
This will help to reduce the number of IO/TLB flushes when
IOMMU drivers support this interface.
- Support for mt2712 in the Mediatek IOMMU driver
- New IOMMU driver for QCOM hardware
- System PM support for ARM-SMMU
- Shutdown method for ARM-SMMU-v3
- Some constification patches
- Various other small improvements and fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=EVh9
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU updates from Joerg Roedel:
"Slightly more changes than usual this time:
- KDump Kernel IOMMU take-over code for AMD IOMMU. The code now tries
to preserve the mappings of the kernel so that master aborts for
devices are avoided. Master aborts cause some devices to fail in
the kdump kernel, so this code makes the dump more likely to
succeed when AMD IOMMU is enabled.
- common flush queue implementation for IOVA code users. The code is
still optional, but AMD and Intel IOMMU drivers had their own
implementation which is now unified.
- finish support for iommu-groups. All drivers implement this feature
now so that IOMMU core code can rely on it.
- finish support for 'struct iommu_device' in iommu drivers. All
drivers now use the interface.
- new functions in the IOMMU-API for explicit IO/TLB flushing. This
will help to reduce the number of IO/TLB flushes when IOMMU drivers
support this interface.
- support for mt2712 in the Mediatek IOMMU driver
- new IOMMU driver for QCOM hardware
- system PM support for ARM-SMMU
- shutdown method for ARM-SMMU-v3
- some constification patches
- various other small improvements and fixes"
* tag 'iommu-updates-v4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (87 commits)
iommu/vt-d: Don't be too aggressive when clearing one context entry
iommu: Introduce Interface for IOMMU TLB Flushing
iommu/s390: Constify iommu_ops
iommu/vt-d: Avoid calling virt_to_phys() on null pointer
iommu/vt-d: IOMMU Page Request needs to check if address is canonical.
arm/tegra: Call bus_set_iommu() after iommu_device_register()
iommu/exynos: Constify iommu_ops
iommu/ipmmu-vmsa: Make ipmmu_gather_ops const
iommu/ipmmu-vmsa: Rereserving a free context before setting up a pagetable
iommu/amd: Rename a few flush functions
iommu/amd: Check if domain is NULL in get_domain() and return -EBUSY
iommu/mediatek: Fix a build warning of BIT(32) in ARM
iommu/mediatek: Fix a build fail of m4u_type
iommu: qcom: annotate PM functions as __maybe_unused
iommu/pamu: Fix PAMU boot crash
memory: mtk-smi: Degrade SMI init to module_init
iommu/mediatek: Enlarge the validate PA range for 4GB mode
iommu/mediatek: Disable iommu clock when system suspend
iommu/mediatek: Move pgtable allocation into domain_alloc
iommu/mediatek: Merge 2 M4U HWs into one iommu domain
...
General updates:
* Constify pci_device_id in various drivers
* Constify device_type
* Remove pad control code from the Gemini driver
* Use %pOF to print OF node full_name
* Various fixes in the physmap_of driver
* Remove unused vars in mtdswap
* Check devm_kzalloc() return value in the spear_smi driver
* Check clk_prepare_enable() return code in the st_spi_fsm driver
* Create per MTD device debugfs enties
NAND updates, from Boris Brezillon:
* Fix memory leaks in the core
* Remove unused NAND locking support
* Rename nand.h into rawnand.h (preparing support for spi NANDs)
* Use NAND_MAX_ID_LEN where appropriate
* Fix support for 20nm Hynix chips
* Fix support for Samsung and Hynix SLC NANDs
* Various cleanup, improvements and fixes in the qcom driver
* Fixes for bugs detected by various static code analysis tools
* Fix mxc ooblayout definition
* Add a new part_parsers to tmio and sharpsl platform data in order to
define a custom list of partition parsers
* Request the reset line in exclusive mode in the sunxi driver
* Fix a build error in the orion-nand driver when compiled for ARMv4
* Allow 64-bit mvebu platforms to select the PXA3XX driver
SPI NOR updates, from Cyrille Pitchen and Marek Vasut:
* add support to the JEDEC JESD216B specification (SFDP tables).
* add support to the Intel Denverton SPI flash controller.
* fix error recovery for Spansion/Cypress SPI NOR memories.
* fix 4-byte address management for the Aspeed SPI controller.
* add support to some Microchip SST26 memory parts
* remove unneeded pinctrl header Write a message for tag:
-----BEGIN PGP SIGNATURE-----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=UgCd
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20170904' of git://git.infradead.org/linux-mtd
Pull MTD updates from Boris Brezillon:
"General updates:
- Constify pci_device_id in various drivers
- Constify device_type
- Remove pad control code from the Gemini driver
- Use %pOF to print OF node full_name
- Various fixes in the physmap_of driver
- Remove unused vars in mtdswap
- Check devm_kzalloc() return value in the spear_smi driver
- Check clk_prepare_enable() return code in the st_spi_fsm driver
- Create per MTD device debugfs enties
NAND updates, from Boris Brezillon:
- Fix memory leaks in the core
- Remove unused NAND locking support
- Rename nand.h into rawnand.h (preparing support for spi NANDs)
- Use NAND_MAX_ID_LEN where appropriate
- Fix support for 20nm Hynix chips
- Fix support for Samsung and Hynix SLC NANDs
- Various cleanup, improvements and fixes in the qcom driver
- Fixes for bugs detected by various static code analysis tools
- Fix mxc ooblayout definition
- Add a new part_parsers to tmio and sharpsl platform data in order
to define a custom list of partition parsers
- Request the reset line in exclusive mode in the sunxi driver
- Fix a build error in the orion-nand driver when compiled for ARMv4
- Allow 64-bit mvebu platforms to select the PXA3XX driver
SPI NOR updates, from Cyrille Pitchen and Marek Vasut:
- add support to the JEDEC JESD216B specification (SFDP tables).
- add support to the Intel Denverton SPI flash controller.
- fix error recovery for Spansion/Cypress SPI NOR memories.
- fix 4-byte address management for the Aspeed SPI controller.
- add support to some Microchip SST26 memory parts
- remove unneeded pinctrl header Write a message for tag:"
* tag 'for-linus-20170904' of git://git.infradead.org/linux-mtd: (74 commits)
mtd: nand: complain loudly when chip->bits_per_cell is not correctly initialized
mtd: nand: make Samsung SLC NAND usable again
mtd: nand: tmio: Register partitions using the parsers
mfd: tmio: Add partition parsers platform data
mtd: nand: sharpsl: Register partitions using the parsers
mtd: nand: sharpsl: Add partition parsers platform data
mtd: nand: qcom: Support for IPQ8074 QPIC NAND controller
mtd: nand: qcom: support for IPQ4019 QPIC NAND controller
dt-bindings: qcom_nandc: IPQ8074 QPIC NAND documentation
dt-bindings: qcom_nandc: IPQ4019 QPIC NAND documentation
dt-bindings: qcom_nandc: fix the ipq806x device tree example
mtd: nand: qcom: support for different DEV_CMD register offsets
mtd: nand: qcom: QPIC data descriptors handling
mtd: nand: qcom: enable BAM or ADM mode
mtd: nand: qcom: erased codeword detection configuration
mtd: nand: qcom: support for read location registers
mtd: nand: qcom: support for passing flags in DMA helper functions
mtd: nand: qcom: add BAM DMA descriptor handling
mtd: nand: qcom: allocate BAM transaction
mtd: nand: qcom: DMA mapping support for register read buffer
...
This extends the Qualcomm GLINK implementation to support the additional
features used for communicating with modem and DSP coprocessors in modern
Qualcomm platforms.
In addition to this there's support for placing virtio RPMSG buffers in
non-System RAM.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=PVGN
-----END PGP SIGNATURE-----
Merge tag 'rpmsg-v4.14' of git://github.com/andersson/remoteproc
Pull rpmsg updates from Bjorn Andersson:
"This extends the Qualcomm GLINK implementation to support the
additional features used for communicating with modem and DSP
coprocessors in modern Qualcomm platforms.
In addition to this there's support for placing virtio RPMSG buffers
in non-System RAM"
* tag 'rpmsg-v4.14' of git://github.com/andersson/remoteproc: (29 commits)
rpmsg: glink: initialize ret to zero to ensure error status check is correct
rpmsg: glink: fix null pointer dereference on a null intent
dt-bindings: soc: qcom: Extend GLINK to cover SMEM
remoteproc: qcom: adsp: Allow defining GLINK edge
rpmsg: glink: Export symbols from common code
rpmsg: glink: Release idr lock before returning on error
rpmsg: glink: Handle remote rx done command
rpmsg: glink: Request for intents when unavailable
rpmsg: glink: Use the intents passed by remote
rpmsg: glink: Receive and store the remote intent buffers
rpmsg: glink: Add announce_create ops and preallocate intents
rpmsg: glink: Add rx done command
rpmsg: glink: Make RX FIFO peak accessor to take an offset
rpmsg: glink: Use the local intents when receiving data
rpmsg: glink: Add support for TX intents
rpmsg: glink: Fix idr_lock from mutex to spinlock
rpmsg: glink: Add support for transport version negotiation
rpmsg: glink: Introduce glink smem based transport
rpmsg: glink: Do a mbox_free_channel in remove
rpmsg: glink: Return -EAGAIN when there is no FIFO space
...
This adds and improves remoteproc support for TI DA8xx/OMAP-L13x DSP, TI
Keystone 66AK2G DSP and iMX6SX/7D Cortex M4 coprocessors. It introduces the
Qualcomm restart notifier and a few fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=R9dP
-----END PGP SIGNATURE-----
Merge tag 'rproc-v4.14' of git://github.com/andersson/remoteproc
Pull remoteproc updates from Bjorn Andersson:
"This adds and improves remoteproc support for TI DA8xx/OMAP-L13x DSP,
TI Keystone 66AK2G DSP and iMX6SX/7D Cortex M4 coprocessors. It
introduces the Qualcomm restart notifier and a few fixes"
* tag 'rproc-v4.14' of git://github.com/andersson/remoteproc:
remoteproc: Introduce rproc handle accessor for children
remoteproc: qcom: Make ssr_notifiers local
remoteproc: Stop subdevices in reverse order
remoteproc: imx_rproc: add a NXP/Freescale imx_rproc driver
remoteproc: dt: Provide bindings for iMX6SX/7D Remote Processor Controller driver
remoteproc: qcom: Use PTR_ERR_OR_ZERO
remoteproc: st: explicitly request exclusive reset control
remoteproc: qcom: explicitly request exclusive reset control
remoteproc/keystone: explicitly request exclusive reset control
remoteproc/keystone: Add support for Keystone 66AK2G SOCs
remoteproc/davinci: Add device tree support for OMAP-L138 DSP
dt-bindings: remoteproc: Add bindings for Davinci DSP processors
remoteproc/davinci: Add support to parse internal memories
remoteproc/davinci: Switch to platform_get_resource_byname()
remoteproc: make device_type const
soc: qcom: GLINK SSR notifier
remoteproc: qcom: Add support for SSR notifications
remoteproc: Merge __rproc_boot() with rproc_boot()
Pull i2c updates from Wolfram Sang:
- new drivers for Spreadtrum I2C, Intel Cherry Trail Whiskey Cove SMBUS
- quite some driver updates
- cleanups for the i2c-mux subsystem
- some subsystem-wide constification
- further cleanup of include/linux/i2c
* 'i2c/for-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (50 commits)
i2c: sprd: Fix undefined reference errors
i2c: nomadik: constify amba_id
i2c: versatile: Make i2c_algo_bit_data const
i2c: busses: make i2c_adapter_quirks const
i2c: busses: make i2c_adapter const
i2c: busses: make i2c_algorithm const
i2c: Add Spreadtrum I2C controller driver
dt-bindings: i2c: Add Spreadtrum I2C controller documentation
i2c-cht-wc: make cht_wc_i2c_adap_driver static
MAINTAINERS: Add entry for drivers/i2c/busses/i2c-cht-wc.c
i2c: aspeed: Retain delay/setup/hold values when configuring bus frequency
dt-bindings: i2c: eeprom: Document vendor to be used and deprecated ones
i2c: i801: Restore the presence state of P2SB PCI device after reading BAR
MAINTAINERS: drop entry for Blackfin I2C and Sonic's email
blackfin: merge the two TWI header files
i2c: davinci: Preserve return value of devm_clk_get
i2c: mediatek: Add i2c compatible for MediaTek MT7622
dt-bindings: i2c: Add MediaTek MT7622 i2c binding
dt-bindings: i2c: modify information formats
i2c: mux: i2c-arb-gpio-challenge: allow compiling w/o OF support
...
Document support for the Watchdog Timer (WDT) Controller in the Renesas
R-Car D3 (r8a77995) SoC.
No driver update is needed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
For the AST2500 and compatible watchdog controllers the external reset
signal can be configured for push-pull or open-drain drive types, and in
the case of push-pull driving, active low or high.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Chunfeng Yun