Default clock frequency for ARC PGU does not match any
existing HDMI mode, instead the default value matches a
DVI mode. Change the clock frequency to 74.25MHz so that
it matches HDMI mode 1280x720@60Hz
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Carlos Palminha <palminha@synopsys.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: devicetree@vger.kernel.org
Cc: linux-snps-arc@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Acked-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
This patch adds the necessary DT bindings to get HDMI audio
output in ARC AXS10x SDP. The bindings for I2S controller were
added as well as the bindings for simple audio card.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Carlos Palminha <palminha@synopsys.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: devicetree@vger.kernel.org
Cc: linux-snps-arc@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
MotherBoard section has its "ranges" set to 0xE000_0000-0xF000_0000.
But UIO node maps 4 different areas in different memory locations
and all outside MB's ranges.
That obviously breaks UIO mappings in runtime.
Cc: Ruud Derwig <rderwig@synopsys.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Trying to get clock for CPU cores on SMP systems I found that I was only
able to get clock for core[0]. That was because only one cpu@0 node was
represented in ARC HS device tree and it was impossible to get clock for
"non-existing" cores.
So as ARC HS may have up to 4 cores we update device tree to match
maximum possible cores quantity.
Signed-off-by: Vlad Zakharov <vzakhar@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
ARC CPU cores are driven by core_clk so we add corresponding "clocks"
property to ARC cpu nodes.
Signed-off-by: Vlad Zakharov <vzakhar@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
No need for specifying a list of interrupts in the declaration
of IDU interrupt controller anymore since the kernel can obtain
a number of supported interrupts from the build register.
Also delete support of the second parameter for devices which
are connected to IDU because it is not used anywhere.
Signed-off-by: Yuriy Kolerov <yuriy.kolerov@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
ARC VDK for EVSS uses UIO for communication with Embedded Vision
Subsystem.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
- Moving ARC timer driver into drivers/clocksource
- EZChip timer driver updates [Noam]
- ARC AXS103 and HAPS platform updates [Alexey]
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=1Hlx
-----END PGP SIGNATURE-----
Merge tag 'arc-4.10-rc1-part1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC updates from Vineet Gupta:
"These are mostly timer/clocksource driver updates which were
Reviewed/Acked by Daniel but had to be merged via ARC tree due to
dependencies.
I will follow up with another pull request with actual ARC changes
early next week !
Summary:
- Moving ARC timer driver into drivers/clocksource
- EZChip timer driver updates [Noam]
- ARC AXS103 and HAPS platform updates [Alexey]"
* tag 'arc-4.10-rc1-part1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: axs10x: really enable ARC PGU
ARC: rename Zebu platform support to HAPS
clocksource: nps: avoid maybe-uninitialized warning
clocksource: Add clockevent support to NPS400 driver
clocksource: update "fn" at CLOCKSOURCE_OF_DECLARE() of nps400 timer
soc: Support for NPS HW scheduling
clocksource: import ARC timer driver
ARC: breakout timer include code into separate header ...
ARC: move mcip.h into include/soc and adjust the includes
ARC: breakout aux handling into a separate header
ARC: time: move time_init() out of the driver
ARC: timer: gfrc, rtc: build under same option (64-bit timers)
ARC: timer: gfrc, rtc: Read BCR to detect whether hardware exists ...
ARC: timer: gfrc, rtc: deuglify big endian code
Fairly routine update this time around with all changes specific to drivers.
o New driver for STMicroelectronics FDMA
o Memory-to-memory transfers on dw dmac
o Support for slave maps on pl08x devices
o Bunch of driver fixes to use dma_pool_zalloc
o Bunch of compile and warning fixes spread across drivers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Pf0d
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-4.10-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
"Fairly routine update this time around with all changes specific to
drivers:
- New driver for STMicroelectronics FDMA
- Memory-to-memory transfers on dw dmac
- Support for slave maps on pl08x devices
- Bunch of driver fixes to use dma_pool_zalloc
- Bunch of compile and warning fixes spread across drivers"
[ The ST FDMA driver already came in earlier through the remoteproc tree ]
* tag 'dmaengine-4.10-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (68 commits)
dmaengine: sirf-dma: remove unused ‘sdesc’
dmaengine: pl330: remove unused ‘regs’
dmaengine: s3c24xx: remove unused ‘cdata’
dmaengine: stm32-dma: remove unused ‘src_addr’
dmaengine: stm32-dma: remove unused ‘dst_addr’
dmaengine: stm32-dma: remove unused ‘sfcr’
dmaengine: pch_dma: remove unused ‘cookie’
dmaengine: mic_x100_dma: remove unused ‘data’
dmaengine: img-mdc: remove unused ‘prev_phys’
dmaengine: usb-dmac: remove unused ‘uchan’
dmaengine: ioat: remove unused ‘res’
dmaengine: ioat: remove unused ‘ioat_dma’
dmaengine: ioat: remove unused ‘is_raid_device’
dmaengine: pl330: do not generate unaligned access
dmaengine: k3dma: move to dma_pool_zalloc
dmaengine: at_hdmac: move to dma_pool_zalloc
dmaengine: at_xdmac: don't restore unsaved status
dmaengine: ioat: set error code on failures
dmaengine: ioat: set error code on failures
dmaengine: DW DMAC: add multi-block property to device tree
...
Up until now we had ARC PGU not enabled in axs10x defconfigs trying
to not bloat kernel image again with yet another drivers and subsystems.
This change configures ARC PGU (as well as DRM bits it depends on)
to be built as a module and so those who need LCD screen to work on
axs10x may bundle built .ko files in their target's file-system with
help of the following command on host:
------------->8-------------
make INSTALL_MOD_PATH=_path_to_target_fs_ modules_install
------------->8-------------
and later on target with commands as simple as:
------------->8-------------
modprobe adv7511.ko
modprobe arcpgu.ko
------------->8-------------
get LCD working.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
There are more ARC Linux HAPS users than Zebu ones.
Same kernel would work fine on both, even with embedded DT, assuming the FPGA
bitfile configuration is same
Suggested-by: Francois Bedard <fbedard@ynopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Several versions of DW DMAC have multi block transfers hardware
support. Hardware support of multi block transfers is disabled
by default if we use DT to configure DMAC and software emulation
of multi block transfers used instead.
Add multi-block property, so it is possible to enable hardware
multi block transfers (if present) via DT.
Switch from per device is_nollp variable to multi_block array
to be able enable/disable multi block transfers separately per
channel.
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Now when we have properly working performance counters in nSIM
even with interrupt support (fix should be a part of upcoming
nSIM engineering build 2016.12-005) we may enable perf support
by default for all platforms that use nSIM for ARC cores simulation.
Note 1: PCT node was missing for some reason in nsimosci.dts
while all other nSIM-related .dts files already had
PCT node for quite some time, so adding it now.
Note 2: All defconfigs were regenerated with "make savedefconfig"
which led to some clean-ups in nsimosci_hs_smp_defconfig:
CONFIG_FRAMEBUFFER_CONSOLE=y was removed because it is
automatically selected now by DRM.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Add support for lzma compressed uImage.
Support for gzip was already available but could not be enabled because
we were missing CONFIG_HAVE_KERNEL_GZIP in arch/arc/Kconfig.
Signed-off-by: Daniel Mentz <danielmentz@google.com>
Cc: linux-snps-arc@lists.infradead.org
Cc: Vineet Gupta <Vineet.Gupta1@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
The cool thing is that same kernel image can run on
- nsim OSCI simulation platform
- SDPlite FPGA setups
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
As it was discussed quite some time ago (see
https://lkml.org/lkml/2015/11/5/862) it's a good practice to add
"model" property in .dts. Moreover as per ePAPR "model" property is
required and should look like "manufacturer,model" so we do here.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Jonas Gorski <jonas.gorski@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Rob Herring <robh@kernel.org>
Cc: Christian Ruppert <christian.ruppert@alitech.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXcHi9AAoJEHm+PkMAQRiGSJ0H/2o4t9VWYmhyPC1sdIHoCExJ
P4tBrcZYBmKcsOmIfnJDa5g/+IdhouEUM0v0fHPogS2UUWT9eRuJWYD3sY+HpEQ+
heKTli8X73gsFB25odeIbIt0jAoSiiMYWDrWqLNsuUV1tjEYVA8rH0SM94FiOC/5
7WVWXLTuH+Rm7JHP18BnKxmMMbzrTFmwisLMqFKyfZRRSlS+/ix7iLUNO9AFa39B
YHxNPihLrZ0oONyCOAQoHTIXXrw0cQbxV2utg3vnMcCZdme2xOn+iXMntTSKfZ39
iC9/T0vsO3R6OrRo2aDZAnCPUAniXnMEIhrKG37WMyXpj6cucZ/2QiNXcXviGV4=
=iLte
-----END PGP SIGNATURE-----
Back-merge tag 'v4.7-rc5' into drm-next
Linux 4.7-rc5
The fsl-dcu pull needs -rc3 so go to -rc5 for now.
With required ARC PGU updates that allow it to be used on simulation
platforms we may finally utilize ARC PGU in nSIM OSCI virtual platforms
with modern Linux kernels.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
With required ARC PGU updates that allow it to be used on simulation
platforms we may finally utilize ARC PGU in HS38 VDK with modern
Linux kernels.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Now when we switched to usage of real clk devices for CPU core
frequency those root properties make no sense any longer.
Se we're just getting rid of them here to not confuse readers of
our .dts files.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Christian Ruppert <christian.ruppert@alitech.com>
Cc: Noam Camus <noamca@mellanox.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Pull drm updates from Dave Airlie:
"Here's the main drm pull request for 4.7, it's been a busy one, and
I've been a bit more distracted in real life this merge window. Lots
more ARM drivers, not sure if it'll ever end. I think I've at least
one more coming the next merge window.
But changes are all over the place, support for AMD Polaris GPUs is in
here, some missing GM108 support for nouveau (found in some Lenovos),
a bunch of MST and skylake fixes.
I've also noticed a few fixes from Arnd in my inbox, that I'll try and
get in asap, but I didn't think they should hold this up.
New drivers:
- Hisilicon kirin display driver
- Mediatek MT8173 display driver
- ARC PGU - bitstreamer on Synopsys ARC SDP boards
- Allwinner A13 initial RGB output driver
- Analogix driver for DisplayPort IP found in exynos and rockchip
DRM Core:
- UAPI headers fixes and C++ safety
- DRM connector reference counting
- DisplayID mode parsing for Dell 5K monitors
- Removal of struct_mutex from drivers
- Connector registration cleanups
- MST robustness fixes
- MAINTAINERS updates
- Lockless GEM object freeing
- Generic fbdev deferred IO support
panel:
- Support for a bunch of new panels
i915:
- VBT refactoring
- PLL computation cleanups
- DSI support for BXT
- Color manager support
- More atomic patches
- GEM improvements
- GuC fw loading fixes
- DP detection fixes
- SKL GPU hang fixes
- Lots of BXT fixes
radeon/amdgpu:
- Initial Polaris support
- GPUVM/Scheduler/Clock/Power improvements
- ASYNC pageflip support
- New mesa feature support
nouveau:
- GM108 support
- Power sensor support improvements
- GR init + ucode fixes.
- Use GPU provided topology information
vmwgfx:
- Add host messaging support
gma500:
- Some cleanups and fixes
atmel:
- Bridge support
- Async atomic commit support
fsl-dcu:
- Timing controller for LCD support
- Pixel clock polarity support
rcar-du:
- Misc fixes
exynos:
- Pipeline clock support
- Exynoss4533 SoC support
- HW trigger mode support
- export HDMI_PHY clock
- DECON5433 fixes
- Use generic prime functions
- use DMA mapping APIs
rockchip:
- Lots of little fixes
vc4:
- Render node support
- Gamma ramp support
- DPI output support
msm:
- Mostly cleanups and fixes
- Conversion to generic struct fence
etnaviv:
- Fix for prime buffer handling
- Allow hangcheck to be coalesced with other wakeups
tegra:
- Gamme table size fix"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (1050 commits)
drm/edid: add displayid detailed 1 timings to the modelist. (v1.1)
drm/edid: move displayid validation to it's own function.
drm/displayid: Iterate over all DisplayID blocks
drm/edid: move displayid tiled block parsing into separate function.
drm: Nuke ->vblank_disable_allowed
drm/vmwgfx: Report vmwgfx version to vmware.log
drm/vmwgfx: Add VMWare host messaging capability
drm/vmwgfx: Kill some lockdep warnings
drm/nouveau/gr/gf100-: fix race condition in fecs/gpccs ucode
drm/nouveau/core: recognise GM108 chipsets
drm/nouveau/gr/gm107-: fix touching non-existent ppcs in attrib cb setup
drm/nouveau/gr/gk104-: share implementation of ppc exception init
drm/nouveau/gr/gk104-: move rop_active_fbps init to nonctx
drm/nouveau/bios/pll: check BIT table version before trying to parse it
drm/nouveau/bios/pll: prevent oops when limits table can't be parsed
drm/nouveau/volt/gk104: round up in gk104_volt_set
drm/nouveau/fb/gm200: setup mmu debug buffer registers at init()
drm/nouveau/fb/gk20a,gm20b: setup mmu debug buffer registers at init()
drm/nouveau/fb/gf100-: allocate mmu debug buffers
drm/nouveau/fb: allow chipset-specific actions for oneinit()
...
This time round the update brings in following changes:
- New tegra driver for ADMA device
- Support for Xilinx AXI Direct Memory Access Engine and Xilinx AXI Central
Direct Memory Access Engine and few updates to this driver.
- New cyclic capability to sun6i and few updates.
- Slave-sg support in bcm2835.
- Updates to many drivers like designware, hsu, mv_xor, pxa, edma,
qcom_hidma & bam.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=0Sy7
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-4.7-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
"This time round the update brings in following changes:
- new tegra driver for ADMA device
- support for Xilinx AXI Direct Memory Access Engine and Xilinx AXI
Central Direct Memory Access Engine and few updates to this driver
- new cyclic capability to sun6i and few updates
- slave-sg support in bcm2835
- updates to many drivers like designware, hsu, mv_xor, pxa, edma,
qcom_hidma & bam"
* tag 'dmaengine-4.7-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (84 commits)
dmaengine: ioatdma: disable relaxed ordering for ioatdma
dmaengine: of_dma: approximate an average distribution
dmaengine: core: Use IS_ENABLED() instead of checking for built-in or module
dmaengine: edma: Re-evaluate errors when ccerr is triggered w/o error event
dmaengine: qcom_hidma: add support for object hierarchy
dmaengine: qcom_hidma: add debugfs hooks
dmaengine: qcom_hidma: implement lower level hardware interface
dmaengine: vdma: Add clock support
Documentation: DT: vdma: Add clock support for dmas
dmaengine: vdma: Add config structure to differentiate dmas
MAINTAINERS: Update Tegra DMA maintainers
dmaengine: tegra-adma: Add support for Tegra210 ADMA
Documentation: DT: Add binding documentation for NVIDIA ADMA
dmaengine: vdma: Add Support for Xilinx AXI Central Direct Memory Access Engine
Documentation: DT: vdma: update binding doc for AXI CDMA
dmaengine: vdma: Add Support for Xilinx AXI Direct Memory Access Engine
Documentation: DT: vdma: update binding doc for AXI DMA
dmaengine: vdma: Rename xilinx_vdma_ prefix to xilinx_dma
dmaengine: slave means at least one of DMA_SLAVE, DMA_CYCLIC
dmaengine: mv_xor: Allow selecting mv_xor for mvebu only compatible SoC
...
The most recent release of AXS103 [v1.1] is proven to work
at 100 MHz in dual-core mode so this change uses mentioned feature.
For that we:
* Update axc003_idu.dtsi with mention of really-used CPU clock freq
* Remove clock override in AXS platform code for dual-core HW
Note we're still leaving a hack for clock "downgrade" on early boot
for quad-core hardware.
Also note this change will break functionality of AXS103 v1.0 hardware.
That means all users of AXS103 __must__ upgrade their boards with the
most recent firmware.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Please pull this mini-series that allows ARC PGU to use
dedicated memory location as framebuffer backing storage.
* 'topic-arcpgu-updates' of https://github.com/foss-for-synopsys-dwc-arc-processors/linux:
ARC: [axs10x] Specify reserved memory for frame buffer
drm/arcpgu: use dedicated memory area for frame buffer
ARC Timers have historically been probed directly.
As precursor to start probing Timers thru DT introduce these bindings
Note that to keep series bisectable, these bindings are not yet used in
code.
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: devicetree@vger.kernel.org
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
This allows us to introduce timers in DT in next commit
The core clk frequency hack in AXS103 platform is also extended,
where the core clk feeding into timers is updated in-place in FDT.
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Rob Herring <robh@kernel.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
... and add them to plat-sim DTS.
This allows for future change to introduce timers in DT in single place
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXL7HfAAoJEHm+PkMAQRiGYe8IAJBGaPUq38EJh2YOV+AQf9v6
t/alhwB3DUE1E0zjLy7I7JJ+xDXtKjZh9fS6OFuIS8Q3RIrBteIJ/oH8TPpt7yZ/
SnP6rYPvYD6CImTyrh7+ORL/udEwJX8+YqFYAgUAq167gvpDjYj8r26VzdIaIN4/
oBbL8NrQNWfODieywYyhUoitVhwMz09zmBfLtGVks4vd2jUJk2Fdd9cOtGV5tRfk
DPndPgyQtbr8W0mKovV8sT9WkQeV5TsUr4MLgf7hjnAGYQ8+0KamkzzVVLBeBiiw
uazyrOCFkddZp+N7KbmbOmazV/yULRuLGgDjVKazoCsOaKOvoGCzrCk7daOPy6Q=
=CegX
-----END PGP SIGNATURE-----
Merge tag 'v4.6-rc7' into drm-next
Merge this back as we've built up a fair few conflicts, and I have
some newer trees to pull in.
There several changes are done here:
- Convert the property to be in bytes
Besides that this is a common practice for such property, the use of a value
in bytes much more convenient than handling the encoded one.
- Rename data_width to data-width in the device tree bindings
The change leaves the support for the old format as well just in case someone
will use a newer kernel with an old device tree blob.
- While here, replace dwc_fast_ffs() by __ffs()
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Allocation of a frame buffer memory in a special memory region
allows bypassing of so-called IO Coherency aperture
which is typically set as a range 0x8z-0xAz.
I.e. all data traffic to PGU bypasses IO Coherency block
and saves its bandwidth for other peripherals.
Even though for AXS101 (which sorts ARC770 CPU) IOC is not
an option for a sake of keeping one DT description for the
base-board (axs10x_mb.dtsi) we're still defining reserved
memory location in the very end of DDR.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
Cc: devicetree@vger.kernel.org
This reverts commit 667a490bdb.
This is needed to get ethernet(stmmac) working in 4.6-rc2 on axs103.
4.5 needed this fix, but apprently stmmac has gained some fixes which
warrant reversal of this.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Commit e34d65696d ("stmmac: create of compatible mdio bus for stmmac
driver") broke DW GMAC functionality on ARC AXS10x boards:
That's what happens on eth0 up:
--------------------------->8------------------------
| libphy: PHY stmmac-0:ffffffff not found
| eth0: Could not attach to PHY
| stmmac_open: Cannot attach to PHY (error: -19)
--------------------------->8------------------------
Simplest solution is to add PHY description in board's .dts.
And so we do here.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Phil Reid <preid@electromag.com.au>
Cc: David S. Miller <davem@davemloft.net>
Cc: linux-kernel@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: stable@vger.kernel.org # 4.5
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Since ezchip network driver was adapted to little endian architecture
this patch provides the corresponding arch/arc/{boot/dts,configs}/ updates so
we can switch over to this device-model/driver for OSCI platform.
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Lada Trimasova <ltrimas@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
HIGHMEM support bumped the default memory size for nsim platform to 1G.
Thus total memory ended at the very edge of start of peripherals address
space. With linux link base shifted, memory started bleeding into
peripheral space which caused early boot bad_page spew !
Fixes: 29e332261d ("ARC: mm: HIGHMEM: populate high memory from DT")
Reported-by: Anton Kolesov <akolesov@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Current ARC SDP boards cannot reliably handle 1Gbit
Ethernet connections due to limitations in hardware.
To make sure networking is stable on the board we're
limiting phy to 100 Mbit.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
- DT binding doc consolidation moving similar bindings to common
locations. The majority of these are display related which were
scattered in video/, fb/, drm/, gpu/, and panel/ directories.
- Add new config option, CONFIG_OF_ALL_DTBS, to enable building all dtbs
in the tree for most arches with dts files (except powerpc for now).
- OF_IRQ=n fixes for user enabled CONFIG_OF.
- of_node_put ref counting fixes from Julia Lawall.
- Common DT binding for wakeup-source and deprecation of all similar
bindings.
- DT binding for PXA LCD controller.
- Allow ignoring failed PCI resource translations in order to ignore
64-bit addresses on non-LPAE 32-bit kernels.
- Support setting the NUMA node from DT instead of only from parent
device.
- Couple of earlycon DT parsing fixes for address and options.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=tGCy
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull DeviceTree updates from Rob Herring:
"A fairly large (by DT standards) pull request this time with the
majority being some overdue moving DT binding docs around to
consolidate similar bindings.
- DT binding doc consolidation moving similar bindings to common
locations. The majority of these are display related which were
scattered in video/, fb/, drm/, gpu/, and panel/ directories.
- Add new config option, CONFIG_OF_ALL_DTBS, to enable building all
dtbs in the tree for most arches with dts files (except powerpc for
now).
- OF_IRQ=n fixes for user enabled CONFIG_OF.
- of_node_put ref counting fixes from Julia Lawall.
- Common DT binding for wakeup-source and deprecation of all similar
bindings.
- DT binding for PXA LCD controller.
- Allow ignoring failed PCI resource translations in order to ignore
64-bit addresses on non-LPAE 32-bit kernels.
- Support setting the NUMA node from DT instead of only from parent
device.
- Couple of earlycon DT parsing fixes for address and options"
* tag 'devicetree-for-4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (45 commits)
MAINTAINERS: update DT binding doc locations
devicetree: add Sigma Designs vendor prefix
of: simplify arch_find_n_match_cpu_physical_id() function
Documentation: arm: Fixed typo in socfpga fpga mgr example
Documentation: devicetree: fix reference to legacy wakeup properties
Documentation: devicetree: standardize/consolidate on "wakeup-source" property
drivers: of: removing assignment of 0 to static variable
xtensa: enable building of all dtbs
mips: enable building of all dtbs
metag: enable building of all dtbs
metag: use common make variables for dtb builds
h8300: enable building of all dtbs
arm64: enable building of all dtbs
arm: enable building of all dtbs
arc: enable building of all dtbs
arc: use common make variables for dtb builds
of: add config option to enable building of all dtbs
of/fdt: fix error checking for earlycon address
of/overlay: add missing of_node_put
of/platform: add missing of_node_put
...
Enable building all dtb files when CONFIG_OF_ALL_DTBS is enabled. The dtbs
are not really dependent on a platform being enabled or any other kernel
config, so for testing coverage it is convenient to build all of the dtbs.
This builds all dts files in the tree, not just targets listed.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
Use dtb-y and always make variables to build dtbs instead of explicit
dtbs rule. This is in preparation to support building all dtbs.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
With up-to-date FPGA builds ARC cores are supposed to correctly operate
even with 90 MHz clock (which is a target frequency for AXS103 release).
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: arc-linux-dev@synopsys.com
- CONFIG_ARC_UBOOT_SUPPORT to handle arguments passed in r0, r1, r2
- CONFIG_DEVTMPFS_MOUNT for mouting rootfs since it uses external cpio
for rootfs
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Ruud Derwig <rderwig@synopsys.com>
[vgupta: folded the Main baord DT files for smp/up into one]
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Jose Abreu