pm_runtime_get_sync() increments the runtime PM usage counter even
when it returns an error code. Thus a pairing decrement is needed on
the error handling path to keep the counter balanced.
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Currently pointer ep is being dereferenced before it is null checked
leading to a null pointer dereference issue. Fix this by only assigning
pointer udc once ep is known to be not null. Also remove a debug
message that requires a valid udc which may not be possible at that
point.
Addresses-Coverity: ("Dereference before null check")
Fixes: 24a28e4283 ("USB: gadget driver for LPC32xx")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
If the SS PHY is in P3, there is no pipe_clk, HW may use suspend_clk
for function, as suspend_clk is slow so EP command need more time to
complete, e.g, imx8M suspend_clk is 32K, set ep configuration will
take about 380us per below trace time stamp(44.286278 - 44.285897
= 0.000381):
configfs_acm.sh-822 [000] d..1 44.285896: dwc3_writel: addr
000000006d59aae1 value 00000401
configfs_acm.sh-822 [000] d..1 44.285897: dwc3_readl: addr
000000006d59aae1 value 00000401
... ...
configfs_acm.sh-822 [000] d..1 44.286278: dwc3_readl: addr
000000006d59aae1 value 00000001
configfs_acm.sh-822 [000] d..1 44.286279: dwc3_gadget_ep_cmd:
ep0out: cmd 'Set Endpoint Configuration' [401] params 00001000
00000500 00000000 --> status: Successful
This was originally found on Hisilicon Kirin Soc that need more time
for the device controller to clear the CmdAct of DEPCMD.
Signed-off-by: Yu Chen <chenyu56@huawei.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
USB gadget subsystem uses the following naming convention for UDC
endpoints:
- "ep-a" names for fully configurable endpoints (address, direction and
transfer type can be changed);
- "ep1in", "ep12out-bulk" names for fixed function endpoints (fixed
address, direction and/or transfer type).
Dummy UDC endpoints are capable of full configuration, but named using
the second scheme.
This patch changes the names of generic Dummy UDC endpoints to "ep-aout",
"ep-bin", etc., to advertise that they have configurable addresses and
transfer types (except that Dummy UDC doesn't support ISO transfers), but
fixed direction.
This is required for Raw Gadget (and perhaps for some other drivers),
that reasons about whether an endpoint has configurable address based
on its name.
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Assign interrupt number to USB gadget structure.
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The threaded interrupt handler may still be called after the
usb_gadget_disconnect is called, it causes the structures used
at interrupt handler was freed before it uses, eg the
usb_request. This issue usually occurs we remove the udc function
during the transfer. Below is the example when doing stress
test for android switch function, the EP0's request is freed
by .unbind (configfs_composite_unbind -> composite_dev_cleanup),
but the threaded handler accesses this request during handling
setup packet request.
In fact, there is no protection between unbind the udc
and udc interrupt handling, so we have to avoid the interrupt
handler is occurred or scheduled during the .unbind flow.
init: Sending signal 9 to service 'adbd' (pid 18077) process group...
android_work: did not send uevent (0 0 000000007bec2039)
libprocessgroup: Successfully killed process cgroup uid 0 pid 18077 in 6ms
init: Service 'adbd' (pid 18077) received signal 9
init: Sending signal 9 to service 'adbd' (pid 18077) process group...
libprocessgroup: Successfully killed process cgroup uid 0 pid 18077 in 0ms
init: processing action (init.svc.adbd=stopped) from (/init.usb.configfs.rc:14)
init: Received control message 'start' for 'adbd' from pid: 399 (/vendor/bin/hw/android.hardware.usb@1.
init: starting service 'adbd'...
read descriptors
read strings
Unable to handle kernel read from unreadable memory at virtual address 000000000000002a
android_work: sent uevent USB_STATE=CONNECTED
Mem abort info:
ESR = 0x96000004
EC = 0x25: DABT (current EL), IL = 32 bits
SET = 0, FnV = 0
EA = 0, S1PTW = 0
Data abort info:
ISV = 0, ISS = 0x00000004
CM = 0, WnR = 0
user pgtable: 4k pages, 48-bit VAs, pgdp=00000000e97f1000
using random self ethernet address
[000000000000002a] pgd=0000000000000000
Internal error: Oops: 96000004 [#1] PREEMPT SMP
Modules linked in:
CPU: 0 PID: 232 Comm: irq/68-5b110000 Not tainted 5.4.24-06075-g94a6b52b5815 #92
Hardware name: Freescale i.MX8QXP MEK (DT)
pstate: 00400085 (nzcv daIf +PAN -UAO)
using random host ethernet address
pc : composite_setup+0x5c/0x1730
lr : android_setup+0xc0/0x148
sp : ffff80001349bba0
x29: ffff80001349bba0 x28: ffff00083a50da00
x27: ffff8000124e6000 x26: ffff800010177950
x25: 0000000000000040 x24: ffff000834e18010
x23: 0000000000000000 x22: 0000000000000000
x21: ffff00083a50da00 x20: ffff00082e75ec40
x19: 0000000000000000 x18: 0000000000000000
x17: 0000000000000000 x16: 0000000000000000
x15: 0000000000000000 x14: 0000000000000000
x13: 0000000000000000 x12: 0000000000000001
x11: ffff80001180fb58 x10: 0000000000000040
x9 : ffff8000120fc980 x8 : 0000000000000000
x7 : ffff00083f98df50 x6 : 0000000000000100
x5 : 00000307e8978431 x4 : ffff800011386788
x3 : 0000000000000000 x2 : ffff800012342000
x1 : 0000000000000000 x0 : ffff800010c6d3a0
Call trace:
composite_setup+0x5c/0x1730
android_setup+0xc0/0x148
cdns3_ep0_delegate_req+0x64/0x90
cdns3_check_ep0_interrupt_proceed+0x384/0x738
cdns3_device_thread_irq_handler+0x124/0x6e0
cdns3_thread_irq+0x94/0xa0
irq_thread_fn+0x30/0xa0
irq_thread+0x150/0x248
kthread+0xfc/0x128
ret_from_fork+0x10/0x18
Code: 910e8000 f9400693 12001ed7 79400f79 (3940aa61)
---[ end trace c685db37f8773fba ]---
Kernel panic - not syncing: Fatal exception
SMP: stopping secondary CPUs
Kernel Offset: disabled
CPU features: 0x0002,20002008
Memory Limit: none
Rebooting in 5 seconds..
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Populate USB DT nodes with interconnect properties.
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Sandeep Maheswaram <sanm@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Populate USB DT nodes with interconnect properties.
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Sandeep Maheswaram <sanm@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Add documentation for the interconnects and interconnect-names
properties for USB.
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Sandeep Maheswaram <sanm@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The endpoint configuration used to be stored in the device tree,
however the configuration depend on the "version" of the controller
itself.
Then the EP child node are useless and describe as deprecated in the
documentation binding: remove all the nodes from the SoC device tree
file. Remove also the #address-cells and #size-cells properties that
are no longer needed.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
There is no need to describe the end point in the deice tree. These
properties won't be use anymore, so mark them as deprecated to keep
the old device tree documented.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The endpoint configuration used to be stored in the device tree,
however the configuration depend on the "version" of the controller
itself.
This information is already documented by the compatible string. It
then possible to just rely on the compatible string and completely
remove the full ep configuration done in the device tree as it was
already the case for all the other USB device controller.
Acked-by: Cristian Birsan <cristian.birsan@microchip.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
DWC_usb32 v1.00a and later can use SET_EP_PRIME command to reinitiate a
stream. Use the command to handle NoStream rejection instead of ending
and restarting the endpoint.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Overview of stream transfer requirement:
* A transfer will have a set of TRBs of the same stream ID.
* A transfer is started with a stream ID in START_TRANSFER command.
* A new stream will only start when the previous completes.
Overview of stream events:
* A "prime" from host indicates that its endpoints are active
(buffers prepared and ready to receive/transmit data). The controller
automatically initiates stream if it sees this.
* A "NoStream" rejection event indicates that the host isn't ready.
Host will put the endpoint back to idle state. Device may need to
reinitiate the stream to start transfer again.
* A Stream Found event means host accepted device initiated stream.
Nothing needs to be done from driver.
To initiate a stream, the driver will issue START_TRANSFER command with
a stream ID. To reinitiate the stream, the driver must issue
END_TRANSFER and restart the transfer with START_TRANSFER command with
the same stream ID.
This implementation handles device-initated streams (e.g. UASP driver).
It also handles some hosts' quirky behavior where they only prime each
endpoint once.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Don't prepare TRBs beyond a transfer. In DWC_usb32, its transfer burst
capability may try to read and use TRBs beyond the active transfer. For
other controllers, they don't process the next transfer TRBs until the
current transfer is completed. Explicitly prevent preparing TRBs ahead
for all controllers.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
If a transfer is in-progress, any new request should not kick off
another transfer. The driver needs to wait for the current transfer to
complete before starting off the next transfer. Introduce a new flag
DWC3_EP_WAIT_TRANSFER_COMPLETE for this.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
In DWC3, to prepare TRBs for streams, all the TRBs of a transfer will
use the same stream ID. To start a new stream, the driver needs to wait
for the current transfer to complete or ended (by END_TRANFER command).
As a result, inform the controller of the last TRB of a transfer so that
it knows when a transfer completes and start a new transfer of a new
stream.
Even though the transfer completion handling can be applied for other
non-isoc endpoints, only do it for streams due to its requirement.
It's better to keep the controller's TRB cache full than waiting for
transfer completion and starting a new transfer.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
To switch from one stream to another, this requires the driver to start
a new transfer with a specific stream ID. For a transfer to complete,
the driver needs to indicate the last TRB of a transfer, and it needs to
enable XferComplete event to handle completed TRBs of a transfer. Let's
enable this event only for stream capable endpoints.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
To prepare for handling of XferComplete event, let's refactor and split
up dwc3_gadget_endpoint_transfer_in_progress() to handle TRBs completion
for different events. The handling of TRBs completion will be the same,
but the status of XferComplete event is different than XferInProgress.
No functional change in this commit.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
While handling TRBs completion, if a END_TRANSFER command isn't
completed, don't kick new transfer or issue END_TRANSFER command.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Set the request->is_last to each stream request to indicate that the
request is the last stream request of a transfer. The DWC3 controller
needs to know this info to properly switch streams. The current
implementation of f_tcm uses a single request per transfer, so every
stream request is the last of its stream.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
To take advantage of DWC3 internal TRB prefetch and cache for
performance, inform the controller the last request with stream_id
before switching to a different stream transfer. This allows the
controller to maintain its transfer burst within the stream ID.
Introduce the usb-request is_last field to help inform the DWC3
controller of this.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
DWC_usb32 supports MDWIDTH value larger than 255 and up to 1023. The
field HWPARAMS6[9:8] stores the upper 2-bit values of the DWC_usb32's
MDWIDTH. Check that parameter and properly get the MDWIDTH for
DWC_usb32.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Synopsys introduces a new controller DWC_usb32. It supports dual-lane
and speed up to 20 Gbps, and the DWC3 driver will drive this controller.
Currently the driver uses a single field dwc->revision to ID both
DWC_usb3 and DWC_usb31 and their version number. This was sufficient for
two IPs, but this method doesn't work with additional IPs. As a result,
let's separate the dwc->revision field to 2 separate fields: ip and
revision. The ip field now stores the ID of the controller's IP while
the revision field stores the controller's version number.
This new scheme enforces DWC3 to compare the revision within the same IP
only. As a result, we must update all the revision check of the
controller to check its corresponding IP.
To help with this enforcement, we create a few macros to help with
the common version checks:
DWC3_IP_IS(IP)
DWC3_VER_IS(IP, VERSION)
DWC3_VER_IS_PRIOR(IP, VERSION)
DWC3_VER_IS_WITHIN(IP, LOWER_VERSION, UPPER_VERSION)
DWC3_VER_TYPE_IS_WITHIN(IP, VERSION,
LOWER_VERSION_TYPE,
UPPER_VERSION_TYPE)
The DWC_usb32 controller operates using the same programming model and
with very similar configurations as its previous controllers. Please
note that the various IP and revision checks in this patch match the
current checks for DWC_usb31 version 1.90a. Additional configurations
that are unique to DWC_usb32 are applied separately.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
OTG port on Tegra194 supports GEN1 speeds when in device mode and GEN2
speeds when in host mode. dd port_speed_quirk that configures port to
GEN1/GEN2 speds, corresponding to the mode.
Based on work by WayneChang <waynec@nvidia.com>
Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
This commit adds support for XUSB device mode controller support on
Tegra194 SoC. This is very similar to the existing Tegra186 XUDC, with lpm
support added in addition.
Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Sparse reports a warning at set_link_state()
warning: context imbalance in set_link_state() - unexpected unlock
The root cause is the missing annotation at set_link_state()
Add the missing __must_hold(&dum->lock)
Signed-off-by: Jules Irenge <jbi.octave@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Sparse reports a warning at xudc_handle_setup()
warning: context imbalance in xudc_handle_setup() - unexpected unlock
The root cause is the missing annotation at xudc_handle_setup()
Add the missing __must_hold(&udc->lock) annotation
Signed-off-by: Jules Irenge <jbi.octave@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
module_usb_composite_driver() makes the code simpler by
eliminating boilerplate code.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Fix the following coccicheck warning:
drivers/usb/gadget/udc/omap_udc.c:2579:2-3: Unneeded semicolon
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Fix the following coccicheck warning:
drivers/usb/gadget/udc/mv_u3d_core.c:1551:5-13: WARNING: Comparison to
bool
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Fix the following coccicheck warning:
drivers/usb/gadget/udc/net2272.c:57:12-19: WARNING: Assignment of 0/1 to
bool variable
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Fix the following coccicheck warning:
drivers/usb/dwc3/drd.c:85:3-24: WARNING: Assignment of 0/1 to bool
variable
drivers/usb/dwc3/drd.c:59:2-23: WARNING: Assignment of 0/1 to bool
variable
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The variable status is being assigned a value that is never read
and it is being updated later with a new value. The assignment
is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Clang warns:
drivers/usb/gadget/udc/s3c2410_udc.c:255:11: warning: comparison of
address of 'ep->queue' equal to a null pointer is always false
[-Wtautological-pointer-compare]
if (&ep->queue == NULL)
~~~~^~~~~ ~~~~
1 warning generated.
It is not wrong, queue is not a pointer so if ep is not NULL, the
address of queue cannot be NULL. No other driver does a check like this
and this check has been around since the driver was first introduced,
presumably with no issues so it does not seem like this check should be
something else. Just remove it.
Commit afe956c577 ("kbuild: Enable -Wtautological-compare") exposed
this but it is not the root cause of the warning.
Fixes: 3fc154b6b8 ("USB Gadget driver for Samsung s3c2410 ARM SoC")
Link: https://github.com/ClangBuiltLinux/linux/issues/1004
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Add suspend resume callbacks to notify u_serial of the bus suspend/resume
state.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Add suspend resume callbacks to notify u_serial of the bus suspend/resume
state.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Add suspend resume callbacks to handle the case seen when the bus is
suspended by the HOST, and the device opens the port (cat /dev/ttyGS0).
Gadget controller (like DWC2) doesn't accept usb requests to be queued in
this case (when in L2 state), from the gs_open() call. Error log is printed
- configfs-gadget gadget: acm ttyGS0 can't notify serial state, -11
If the HOST resumes (opens) the bus, the port still isn't functional.
Use suspend/resume callbacks to monitor the gadget suspended state by using
'suspended' flag. In case the port gets opened (cat /dev/ttyGS0), the I/O
stream will be delayed until the bus gets resumed by the HOST.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
When the remote wakeup interrupt is triggered, lx_state is resumed from L2
to L0 state. But when the gadget resume is called, lx_state is still L2.
This prevents the resume callback to queue any request. Any attempt
to queue a request from resume callback will result in:
- "submit request only in active state" debug message to be issued
- dwc2_hsotg_ep_queue() returns -EAGAIN
Call the gadget resume routine after the core is in L0 state.
Fixes: f81f46e1f5 ("usb: dwc2: implement hibernation during bus suspend/resume")
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
This patch changes the function uvc_video_pump to be a separate
scheduled worker. This way the completion handler of each usb request
and every direct caller of the pump has only to schedule the worker
instead of doing the request handling by itself.
Moving the request handling to one thread solves the locking problems
between the three queueing cases in the completion handler, v4l2_qbuf
and video_enable.
Many drivers handle the completion handlers directly in their interrupt
handlers. This patch also reduces the workload on each interrupt.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
This patch corrects the SPDX License Identifier style in
header files related to Renesas USBHS Controller Drivers.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used).
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Fix the following coccicheck warning:
drivers/usb/gadget/function/f_fs.c:2507:2-3: Unneeded semicolon
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
There is now an updated bindings for these SoCs making the old
compatible obsolete.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
There is now a dedicated driver for these SoCs making the old compatible
obsolete.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The registers which are managed by the meson-gxl-usb3 PHY driver are
actually "USB control" registers (which are "glue" registers which
manage OTG detection and routing of the OTG capable port between the
DWC2 peripheral-only controller and the DWC3 host-only controller).
Drop the meson-gxl-usb3 PHY driver now that the dwc3-meson-g12a-usb
driver supports the USB control registers on GXL and GXM SoCs (these
were previously managed by the meson-gxl-usb3 PHY driver).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Add the correcly architectured USB Glue node and adapt all the Amlogic
GXL and GXM board to the new organization.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
In order to add support for the Amlogic GXL/GXM USB Glue, this adds
the corresponding :
- PHY names
- clock names
- USB2 PHY init and mode set
- regmap setup
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
On the Amlogic GXL/GXM SoCs, the OTG PHY status signals are always
connected to the DWC3 controller, thus crashing the controller when
switching to OTG mode when port is not populated with a device/cable to
Host.
Amlogic added a bit to disconnect the OTG PHY status signals from the DWC3
to be used when switching the OTG PHY as Device to the DWC2 controller.
The drawback is that it makes the DWC3 port state machine stall and needs
a full reset of the DWC3 controller to get connect status to the port
connected to the OTG PHY, but not the other one.
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Dinghao Liu