The watchdog interrupt (only used when activating software watchdog)
shouldn't be suspended when entering suspend mode, because it is shared
with a timer device (which request the line with IRQF_NO_SUSPEND) and once
the watchdog "Mode Register" has been written, it cannot be changed (which
means we cannot disable the watchdog interrupt when entering suspend).
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
BCM5301X (ARCH_BCM_5301X) is a new Broadcom architecture using the same
SoC bus driver (bcma) as BCM47XX but based on ARM instead of MIPS.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Add DT support to the jz4740 driver. Simple of_match_ptr. No other
modification for probe needed
Signed-off-by: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The dw_wdt_set_top() function takes in a value in seconds. In
dw_wdt_open() we were calling it with a value that's supposed to
represent the maximum value programmed into the "top" register with a
comment saying that we were trying to set the watchdog to its maximum
value. Instead we ended up setting the watchdog to ~15 seconds.
Let's fix this. However, setting things to the "max" gives me an 86
second watchdog in the system I'm looking at. 86 seconds feels a
little too long. We'll explicitly choose 30 seconds as a more
reasonable value.
NOTE: Ideally this driver should be transitioned to be a real watchdog
driver. Then we could use "watchdog_init_timeout" and let the timeout
be specified in a number of ways (device tree, module parameter, etc).
This patch should be considered a bit of a stopgap solution.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
On some dw_wdt implementations the "top" register may be initted to 0
at bootup. In such a case, each "pat" of the watchdog will reset the
timer to 0xffff. That's pretty short.
The input clock of the wdt can be any of a wide range of values. On
an rk3288 system, I've seen the wdt clock be 24.75 MHz. That means
each tick is ~40ns and we'll count to 0xffff in ~2.6ms.
Because of the above two facts, it's a really good idea to pat the
watchdog after initting the "top" register properly and before
enabling the watchdog. If you don't then there's no way we'll get the
next heartbeat in time.
Jisheng Zhang fixed this problem on some dw_wdt versions by using the
TOP_INIT feature. However, the dw_wdt on rk3288 doesn't have TOP_INIT
so it's a good idea to also pat the watchdog manually.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The watchdog functionality in both chips is almost identical to NCT6779.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Just like in case of other watchdog drivers, use the new kernel core
API to provide restart support.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
On some chips, like the TPS386000, the trigger cannot be disabled
and the CPU must keep toggling the line at all times. Add a switch
"always_running" to keep toggling the GPIO line regardless of the
state of the soft part of the watchdog. The "armed" member keeps
track of whether a timeout must also cause a reset.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Register a restart handler for the da9063 watchdog. System restart is
triggered by sending the shutdown command to the PMIC.
As more-suitable restart handlers may exist, the priority of the
watchdog restart handler is set to 128.
The actual restart method was inspired by a platform-specific patch from
the BSP by Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Steve Twiss <stwiss.opensource@diasemi.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch adds a driver for the Mediatek SoC integrated
watchdog. This driver supports watchdog and software reset
for mt65xx and mt81xx SoCs.
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Tested-by: Eddie Huang <eddie.huang@mediatek.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This allows testing the watchdog easily with distros just by
doing pkill -9 watchdog.
Reported-by: Thomas Dziedzic <gostrc@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Replace device_reset() with devm_reset_control_get() + reset_control_deassert().
Make use of watchdog_init_timeout() instead of setting the timeout manually.
Signed-off-by: John Crispin <blogic@openwrt.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
allow_kdump was enabled as default since following commit.
commit a089361cf5,
watchdog: hpwdt: Unregister NMI events on exit.
But the initialization message was not modified.
So it still shows
HP Watchdog Timer Driver: NMI decoding initialized,
allow kernel dump: ON (default = 0/OFF) <=
This "default = 0/OFF" message may confuse users.
Fix it as "default = 1/ON".
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
IT8783 watchdog works as in IT872x
Tested on Adlink cPCI-6520 boards
Signed-off-by: Paolo Teti <paolo.teti@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The regmap_config struct may be const because it is not modified by the
driver and regmap_init() accepts pointer to const. Make struct
watchdog_ops const as well.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This platform_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Disable power down counter of the watchdog to avoid system resets. The
watchdog power down counter is set automatically by the chip. If it is
not set to 0 in the driver, the system resets.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Improve power management operations(suspend and resume) as part of
dev_pm_ops for IMX2 watchdog driver.
If PM will be supported, please make sure that the wdev->clk
could disable the watchdog's counter input clock source or can
mask watchdog's reset request to the core.
If watchdog is still used by consumers and resumes from deep
sleep state, we need to restart the watchdog again without
enabling the timer.
If watchdog been has started --> stopped by the consumers and
resumes from non-deep sleep state, then start the timer again.
If watchdog has been started --> stopped by the consumers and
resumes from deep sleep state, will do nothing. The watchdog
will be restarted by consumers next time to be used.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Fix the following build warning by passing the expected argument type to
watchdog_active():
drivers/watchdog/imx2_wdt.c: In function 'imx2_wdt_suspend':
drivers/watchdog/imx2_wdt.c:340:2: warning: passing argument 1 of 'watchdog_active' from incompatible pointer type [enabled by default]
In file included from drivers/watchdog/imx2_wdt.c:38:0:
include/linux/watchdog.h:104:20: note: expected 'struct watchdog_device *' but argument is of type 'struct watchdog_device **'
Reported-by: Olof's autobuilder <build@lixom.net>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Add power management operations(suspend and resume) as part of
dev_pm_ops for IMX2 watchdog driver.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
Pull timer core updates from Thomas Gleixner:
"The time(r) departement provides:
- more infrastructure work on the year 2038 issue
- a few fixes in the Armada SoC timers
- the usual pile of fixlets and improvements"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource: armada-370-xp: Use the reference clock on A375 SoC
watchdog: orion: Use the reference clock on Armada 375 SoC
clocksource: armada-370-xp: Add missing clock enable
time: Fix sign bug in NTP mult overflow warning
time: Remove timekeeping_inject_sleeptime()
rtc: Update suspend/resume timing to use 64bit time
rtc/lib: Provide y2038 safe rtc_tm_to_time()/rtc_time_to_tm() replacement
time: Fixup comments to reflect usage of timespec64
time: Expose get_monotonic_coarse64() for in-kernel uses
time: Expose getrawmonotonic64 for in-kernel uses
time: Provide y2038 safe mktime() replacement
time: Provide y2038 safe timekeeping_inject_sleeptime() replacement
time: Provide y2038 safe do_settimeofday() replacement
time: Complete NTP adjustment threshold judging conditions
time: Avoid possible NTP adjustment mult overflow.
time: Rename udelay_test.c to test_udelay.c
clocksource: sirf: Remove hard-coded clock rate
On Atmel AT91, the conversion to device tree is now considered complete,
and all machines that were not already converted in 3.18 are assumed to
be unused and dropped by the maintainer.
All remaining board files that were written in C are dropped, and the
ancient at91x40 sub-platform (based on an MMU-less ARM7) is removed
altogether. Cleaning up the last pieces was great fun, so I took the
time to do some of the coding myself and removed several hundred code
lines that ended up unused after the board files were done.
There are still a couple of AT91 specific device drivers that are not
converted to DT (CF, USB-OTG) and currently not working, and the platform
itself is not "multiplatform"-enabled, but both issues are going to be
taken care of in the 3.20 cycle.
This is split out from the other cleanups purely based on the size
of the branch.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iD8DBQBUhyNX5t5GS2LDRf4RAnjxAKCER7eoLNadu1/93n/a9d1nUz4MoQCcCZUq
BolxCOi0wr4YTcQtp7rHzWI=
=ykAB
-----END PGP SIGNATURE-----
Merge tag 'at91-cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanup on mach-at91 from Arnd Bergmann:
"On Atmel AT91, the conversion to device tree is now considered
complete, and all machines that were not already converted in 3.18 are
assumed to be unused and dropped by the maintainer.
All remaining board files that were written in C are dropped, and the
ancient at91x40 sub-platform (based on an MMU-less ARM7) is removed
altogether. Cleaning up the last pieces was great fun, so I took the
time to do some of the coding myself and removed several hundred code
lines that ended up unused after the board files were done.
There are still a couple of AT91 specific device drivers that are not
converted to DT (CF, USB-OTG) and currently not working, and the
platform itself is not "multiplatform"-enabled, but both issues are
going to be taken care of in the 3.20 cycle.
This is split out from the other cleanups purely based on the size of
the branch"
* tag 'at91-cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (33 commits)
ARM: at91: remove unused board.h file
ARM: at91: remove unneeded header files
ARM: at91/clocksource: remove !DT PIT initializations
ARM: at91: at91rm9200 ST initialization is now DT only
ARM: at91: remove old AT91-specific drivers
ARM: at91: cleanup initilisation code by removing dead code
ARM: at91/Kconfig: select board files automatically
ARM: at91: remove unused IRQ function declarations
ARM: at91: remove legacy IRQ driver and related code
ARM: at91: remove old at91-specific clock driver
ARM: at91: remove clock data in at91sam9n12.c and at91sam9x5.c files
ARM: at91: remove all !DT related configuration options
ARM: at91/trivial: update Kconfig comment to mention SAMA5
ARM: at91: always USE_OF from now on
ARM: at91/Kconfig: remove ARCH_AT91RM9200 option for drivers
ARM: at91: switch configuration option to SOC_AT91RM9200
ARM: at91: remove at91rm9200 legacy board support
ARM: at91: remove at91rm9200 legacy boards files
ARM: at91/Kconfig: remove useless fbdev Kconfig options
ARM: at91: remove at91sam9261/at91sam9g10 legacy board support
...
Daniel Lezcano muttered:
* Marvell timer updates from Ezequiel Garcia
- Add missing clock enable calls for armada
- Change source clock for clocksource and watchdog
* SIRF timer updates from Yanchang Li
- Make clock rate configurable
The precise selection is useless, so we simply remove these dependencies.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
The 25 MHz reference clock has better stability so its use is prefered over the
core clock. Change the Armada 375 clock initialization to use this reference
clock. To ensure the driver is compatible with an old devicetree, also provide
a fallback path which will silently return to the previous behavior.
While here, add the clock specification to the binding documentation.
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Wim Van Sebroeck <wim@iguana.be>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
This patch removes the magic value used for rebooting the board. This
value is useless and leads to a static checker warning as reported by
Dan Carpenter.
Signed-off-by: Carlo Caione <carlo@caione.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
They need HAS_IOMEM, so let them depend on it, the related error (with
allmodconfig under um):
MODPOST 1205 modules
ERROR: "devm_ioremap_resource" [drivers/watchdog/tegra_wdt.ko] undefined!
ERROR: "devm_ioremap_resource" [drivers/watchdog/of_xilinx_wdt.ko] undefined!
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch adds support for the watchdog hardware found in A31 and
newer SoCs. This new hardware has registers at different offsets, and
the system reset control has been split out of the "mode" register
into a new "configuration" register.
Differences not supported by this driver include separate interrupt
lines for each watchdog, instead of sharing an interrupt line and
registers with the timer block.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch adds support for hardware parameters tied to compatible
strings, so similar hardware can reuse the driver.
This will be used to support the newer watchdog found in A31 and
later SoCs. Differences in the new hardware include separate
interrupt lines for each watchdog, and corresponding interrupt
control/status registers. Watchdog control registers were also
slightly rearranged.
Also replace ioread32()/iowrite32() with readl()/writel() in various
places changed.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Register the watchdog as the system restart function
to the new introducing kernel restart call chain in the
driver instead of providing the restart in machine desc.
This restart handler function is from the mxc_restart()
in arch/arm/mach-imx/system.c
Signed-off-by: Jingchang Lu <jingchang.lu@freescale.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The WDT's BITE_TIME warm-reset behavior can be leveraged as a last
resort mechanism for triggering chip reset. Usually, other restart
methods (such as PS_HOLD) are preferrable for issuing a more complete
reset of the chip. As such, keep the priority of the watchdog notifier
low.
Signed-off-by: Josh Cartwright <joshc@codeaurora.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
On a lot of Samsung systems the watchdog is responsible for restarting the
system and until now this code was contained in plat-samsung/watchdog-reset.c.
With the introduction of the restart handlers, this code can now move into
driver itself, removing the need for arch-specific code.
Tested on a S3C2442 based GTA02
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The kernel core now provides an API to trigger a system restart.
Register with it to support restarting the system via. watchdog.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch adds the watchdog driver for the Amlogic Meson SoCs used also
to reboot the device.
Signed-off-by: Carlo Caione <carlo@caione.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
There is no conflict with rtc/rtc-stmp3xxx.c parent
because modified registers in PM functions of stmp3xxx_rtc_wdt
are different.
Signed-off-by: Janusz Uzycki <j.uzycki@elproma.com.pl>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This driver supports the watchdog device inside the DA9063 PMIC.
Signed-off-by: Krystian Garbaciak <krystian.garbaciak@diasemi.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Acked-by: Steve Twiss <stwiss.opensource@diasemi.com>
Tested-by: Steve Twiss <stwiss.opensource@diasemi.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This adds a driver for the watchdog timer available in Ricoh RN5T618
PMIC. The device supports a programmable expiration time of 1, 8, 32
or 128 seconds.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Exynos7 SoC has a Watchdog for Atlas (A57) cores
This patch adds support for the Atlas watchdog.
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Add a driver for the watchdog timer block found in the Krait Processor
Subsystem (KPSS) on the MSM8960, APQ8064, and IPQ8064.
Signed-off-by: Josh Cartwright <joshc@codeaurora.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The TOP_INIT, ie bit 4-7 of the WDOG_TIMEOUT_RANGE_REG_OFFSET register
may be zero, so the timeout period may be very short after initialization
is done, thus the system may be reset soon after enabling. We fix this
problem by also initialising the TOP_INIT when setting TOP in function
dw_wdt_set_top().
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Add Cadence WDT driver. This is used by Xilinx Zynq.
Signed-off-by: Harini Katakam <harinik@xilinx.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
There is no need to store the return value of misc_deregister() in a
variable. Instead we can just return the value directly.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Building booke_wdt fails when trying to build as a module as there is no
early_param() in module. Fix by using module_param() instead of early_param().
Signed-off-by: Pranith Kumar <bobby.prani@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
There is no need to init .owner field.
Based on the patch from Peter Griffin <peter.griffin@linaro.org>
"mmc: remove .owner field for drivers using module_platform_driver"
This patch removes the superflous .owner field for drivers which
use the module_platform_driver API, as this is overriden in
platform_driver_register anyway."
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Convert k10temp, smsc47b397, da9052, da9055 to new hwmon API.
Register ntc_thermistor driver with thermal subsystem.
Add support for F15h M60h to k10temp driver.
Add driver for MEN14F021P00 BMC HWMON driver; this required a merge
with tag mfd-hwmon-leds-watchdog-v3.18.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=vI5p
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-linus-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
- new driver for menf21bmc.
- convert k10temp, smsc47b397, da9052, da9055 to new hwmon API.
- register ntc_thermistor driver with thermal subsystem.
- add support for F15h M60h to k10temp driver.
- add driver for MEN14F021P00 BMC HWMON driver; this required a merge
with tag mfd-hwmon-leds-watchdog-v3.18
* tag 'hwmon-for-linus-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (ab8500) Call kernel_power_off instead of pm_power_off
hwmon: (menf21bmc) Introduce MEN14F021P00 BMC HWMON driver
leds: leds-menf21bmc: Introduce MEN 14F021P00 BMC LED driver
watchdog: menf21bmc_wdt: Introduce MEN 14F021P00 BMC Watchdog driver
mfd: menf21bmc: Introduce MEN 14F021P00 BMC MFD Core driver
hwmon: (ntc_thermistor) Add ntc thermistor to thermal subsystem as a sensor.
hwmon: (smsc47b397) Convert to devm_hwmon_device_register_with_groups
MAINTAINERS: add entry for the PWM fan driver
hwmon: (k10temp) Convert to devm_hwmon_device_register_with_groups
hwmon: (k10temp) Add support for F15h M60h
hwmon: (da9052) Convert to devm_hwmon_device_register_with_groups
hwmon: (da9055) Convert to devm_hwmon_device_register_with_groups
hwmon: (ads1015) Use of_property_read_u32 at appropriate places
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=cP1w
-----END PGP SIGNATURE-----
Merge tag 'restart-handler-for-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull restart handler infrastructure from Guenter Roeck:
"This series was supposed to be pulled through various trees using it,
and I did not plan to send a separate pull request. As it turns out,
the pinctrl tree did not merge with it, is now upstream, and uses it,
meaning there are now build failures.
Please pull this series directly to fix those build failures"
* tag 'restart-handler-for-v3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
arm/arm64: unexport restart handlers
watchdog: sunxi: register restart handler with kernel restart handler
watchdog: alim7101: register restart handler with kernel restart handler
watchdog: moxart: register restart handler with kernel restart handler
arm: support restart through restart handler call chain
arm64: support restart through restart handler call chain
power/restart: call machine_restart instead of arm_pm_restart
kernel: add support for kernel restart handler call chain
The kernel core now provides an API to trigger a system restart. Register
with it instead of setting arm_pm_restart.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jonas Jensen <jonas.jensen@gmail.com>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Tomasz Figa <t.figa@samsung.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The kernel core now provides an API to trigger a system restart. Register
with it to restart the system instead of misusing the reboot notifier.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jonas Jensen <jonas.jensen@gmail.com>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Tomasz Figa <t.figa@samsung.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The kernel now provides an API to trigger a system restart. Register with
it instead of setting arm_pm_restart.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jonas Jensen <jonas.jensen@gmail.com>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Tomasz Figa <t.figa@samsung.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Added driver to support the 14F021P00 BMC Watchdog.
The BMC is a Board Management Controller including watchdog functionality.
Signed-off-by: Andreas Werner <andreas.werner@men.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for 3.17. It contains:
- misc Cavium Octeon, BCM47xx, BCM63xx and Alchemy updates
- MIPS ptrace updates and cleanups
- various fixes that will also go to -stable
- a number of cleanups and small non-critical fixes.
- NUMA support for the Loongson 3.
- more support for MSA
- support for MAAR
- various FP enhancements and fixes"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (139 commits)
MIPS: jz4740: remove unnecessary null test before debugfs_remove
MIPS: Octeon: remove unnecessary null test before debugfs_remove_recursive
MIPS: ZBOOT: implement stack protector in compressed boot phase
MIPS: mipsreg: remove duplicate MIPS_CONF4_FTLBSETS_SHIFT
MIPS: Bonito64: remove a duplicate define
MIPS: Malta: initialise MAARs
MIPS: Initialise MAARs
MIPS: detect presence of MAARs
MIPS: define MAAR register accessors & bits
MIPS: mark MSA experimental
MIPS: Don't build MSA support unless it can be used
MIPS: consistently clear MSA flags when starting & copying threads
MIPS: 16 byte align MSA vector context
MIPS: disable preemption whilst initialising MSA
MIPS: ensure MSA gets disabled during boot
MIPS: fix read_msa_* & write_msa_* functions on non-MSA toolchains
MIPS: fix MSA context for tasks which don't use FP first
MIPS: init upper 64b of vector registers when MSA is first used
MIPS: save/disable MSA in lose_fpu
MIPS: preserve scalar FP CSR when switching vector context
...
Pull s390 updates from Martin Schwidefsky:
"Mostly cleanups and bug-fixes, with two exceptions.
The first is lazy flushing of I/O-TLBs for PCI to improve performance,
the second is software dirty bits in the pmd for the madvise-free
implementation"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (24 commits)
s390/locking: Reenable optimistic spinning
s390/mm: implement dirty bits for large segment table entries
KVM: s390/mm: Fix page table locking vs. split pmd lock
s390/dasd: fix camel case
s390/3215: fix hanging console issue
s390/irq: improve displayed interrupt order in /proc/interrupts
s390/seccomp: fix error return for filtered system calls
s390/pci: introduce lazy IOTLB flushing for DMA unmap
dasd: fix error recovery for alias devices during format
dasd: fix list_del corruption during format
dasd: fix unresponsive device during format
dasd: use aliases for formatted devices during format
s390/pci: fix kmsg component
s390/kdump: Return NOTIFY_OK for all actions other than MEM_GOING_OFFLINE
s390/watchdog: Fix module name in Kconfig help text
s390/dasd: replace seq_printf by seq_puts
s390/dasd: replace pr_warning by pr_warn
s390/dasd: Move EXPORT_SYMBOL after function/variable
s390/dasd: remove unnecessary null test before debugfs_remove
s390/zfcp: use qdio buffer helpers
...
Most of the watchdog code is duplicated between the machine restart code and
the watchdog driver. Add the restart hook to the watchdog driver, to be able to
remove it from the machine code eventually.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This watchdog driver will be working on IMX2+, Vybrid, LS1, LS2+
platforms, and will be in different endianness mode in those SoCs:
SoCs WDT endian mode
------------------------------------
IMX2+ LE
Vybird LE
LS1 BE
LS2 LE
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
devm_ioremap_resource check for a valid resource. Remove the unnecessary check.
Also group platform_get_resource and devm_ioremap_resource together for better
readability.
Signed-off-by: George Cherian <george.cherian@ti.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
devm_ioremap_resource() checks for valid resource.
Remove the un-necessary check after platform_get_resource().
Signed-off-by: George Cherian <george.cherian@ti.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
devm_ioremap_resource() checks for valid resource.
Remove the un-necessary check after platform_get_resource().
Signed-off-by: George Cherian <george.cherian@ti.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
If CONFIG_HOTPLUG_CPU is set, the driver thinks bootloader entry
address is configured and we should jump there. However, this is
not necessarily true if the kernel is booted on a system
with older/incompatible bootloader.
Add dynamic checks for the bootloader entry address.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: linux-watchdog@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: David Daney <ddaney.cavm@gmail.com>
Cc: linux-watchdog@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/7201/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The help text for DIAG288_WATCHDOG in drivers/watchdog/Kconfig
still mentioned the misleading old module name vmwatchdog.
This patch changes that to the correct new name diag288_wdt.
Signed-off-by: Philipp Hachtmann <phacht@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Pull s390 patches from Martin Schwidefsky:
"A couple of bug fixes, a debug change for qdio, an update for the
default config, and one small extension.
The watchdog module based on diagnose 0x288 is converted to the
watchdog API and it now works under LPAR as well"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/ccwgroup: use ccwgroup_ungroup wrapper
s390/ccwgroup: fix an uninitialized return code
s390/ccwgroup: obtain extra reference for asynchronous processing
qdio: Keep device-specific dbf entries
s390/compat: correct ucontext layout for high gprs
s390/cio: set device name as early as possible
s390: update default configuration
s390: avoid format strings leaking into names
s390/airq: silence lockdep warning
s390/watchdog: add support for LPAR operation (diag288)
s390/watchdog: use watchdog API
s390/sclp_vt220: Enable ASCII console per default
s390/qdio: replace shift loop by ilog2
s390/cio: silence lockdep warning
s390/uaccess: always load the kernel ASCE after task switch
s390/ap_bus: Make modules parameters visible in sysfs
Add initial Intel MID watchdog driver support.
This driver is an initial implementation of generic Intel MID watchdog
driver. Currently it supports Intel Merrifield platform.
Signed-off-by: Eric Ernst <eric.ernst@intel.com>
Signed-off-by: David Cohen <david.a.cohen@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Implementation of ->set_timeout() is supposed to set 'timeout' field of 'struct
watchdog_device' passed to it. sp805 was rather setting this in a local
variable. Fix it.
Reported-by: Arun Ramamurthy <arun.ramamurthy@broadcom.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Cc: <stable@vger.kernel.org> # 2.6.36+
Basically, this patch does the following:
1. Move the codes of parsing boot parameters from setup-common.c
to driver. In this way, code reader can know directly that
there are boot parameters that can change the timeout.
2. Make boot parameter 'booke_wdt_period' effective.
currently, when driver is loaded, default timeout is always
being used in stead of booke_wdt_period.
3. Wrap up the watchdog timeout in device struct and clean up
unnecessary codes.
Signed-off-by: Tang Yuantian <yuantian.tang@freescale.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Reviewed-by: Li Yang <leoli@freescale.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
All three iop variants we support in Linux (iop32x, iop33x and
iop13xx) seem to have support for the watchdog hardware, but this
driver fails to build for the first two of these because it
uses the IOP13XX_WDTCR_IB_RESET macro that is only defined for
iop13xx.
This clarifies the dependency in Kconfig to avoid randconfig
build errors. It is unlikely that anyone will ever miss support
for this driver on the ancient iop3xx platforms, so we don't
need to bother trying to fix it properly.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Cc: linux-watchdog@vger.kernel.org
Since both chips are now supported by the w83627hf watchdog driver,
the chip specific drivers are no longer needed and can be removed.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Add early_disable module parameter to match functionality previously
available in the w83697hf_wdt driver.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This commit adds support for the Armada 375 and Armada 380 SoCs.
This SoC variant has a second RSTOUT register, in addition to the already
existent, which is shared with the system-controller. To handle this RSTOUT,
we introduce a new MMIO register 'rstout_mask' to be required on
'armada-{375,380}-watchdog' new compatible string.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Tested-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
In order to support other SoCs, it's needed to have a different enabled()
implementation for each SoC. This commit adds no functionality, and it
consists of preparation work.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Tested-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
In order to support other SoCs, it's needed to have a different stop()
implementation for each SoC. This commit adds no functionality, and it
consists of preparation work.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Tested-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The RSTOUT register on the Armada 370 SoC variant is a dedicated register
(not shared across orthogonal subsystems) and so it's not needed to write
it atomically.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Tested-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Separate the RSTOUT register mapping for the different compatible strings
supported by the driver. This allows to use devm_ioremap on SoC variants that
share the RSTOUT register, and devm_ioremap_resource (which requests the MMIO
region) on SoCs that have a dedicated RSTOUT register.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Tested-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Follow-up patches will extend the registers ioremap and request
to handle SoC-specific quirks on the RSTOUT register. Therefore,
in order to keep the code readable, this commit introduces a special
function for this.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Make of_device_id array const, because all OF functions
handle it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Reviewed-by: Michal Simek <monstr@monstr.eu>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Convert the imx2_wdt driver to the new watchdog core api.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Cc: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This watchdog driver will be working on IMX2+, Vybrid, LS1, LS2+
platforms, and will be in different endianness mode in those SoCs:
SoCs CPU endian mode WDT endian mode
------------------------------------------------
IMX2+ LE LE
Vybird LE LE
LS1 LE BE
LS2 LE LE
Other possible SoCs:
SoCs CPU endian mode WDT endian mode
------------------------------------------------
Soc1 BE BE
Soc2 BE LE
And also the watchdog's registers will be 32-bits for some versions,
and though it is 16-bits in IMX2+, Vybird and LS+.
Using the regmap APIs, could be more easy to support different
endianness and also more easy to support 32-bits version...
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Replace clk_enable() and clk_disable() calls with
clk_prepare_enable() and clk_disable_unprepare()
to get ready for the migration to the common clock
framework.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
On some AR934x based systems, where the frequency of
the AHB bus is relatively high, the built-in watchdog
causes a spurious restart when it gets enabled.
The possible cause of these restarts is that the timeout
value written into the TIMER register does not reaches
the hardware in time.
Add an explicit delay into the ath79_wdt_enable function
to avoid the spurious restarts.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Cc: <stable@vger.kernel.org>
This patch removes platform_set_drvdata() which is not used in
the driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Use the prescaler index, rather than its value, to configure the watchdog.
This will prevent a mismatch with the prescaler used to calculate the cycles.
Signed-off-by: Per Gundberg <per.gundberg@icomera.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Michael Brunner <michael.brunner@kontron.com>
Tested-by: Michael Brunner <michael.brunner@kontron.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Cc: stable <stable@vger.kernel.org>
When compiling sunxi_defconfig while using C=2, the following error
causes the compilation to fail:
drivers/watchdog/sunxi_wdt.c:60:15: error: constant 0b0001 is not a valid number
Fix it by using hex notation instead of the non-standard binary one
Signed-off-by: Emilio Lopez <emilio@elopez.com.ar>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Use del_timer_sync to ensure that the timer is stopped on all CPUs before
the driver exits.
This change was suggested by Thomas Gleixner.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r@
identifier i,t,ex;
@@
struct t i = { .remove = ex, };
@@
identifier r.ex;
@@
ex(...) {
<...
- del_timer
+ del_timer_sync
(...)
...>
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
According to its Kconfig help text, the sbc8360 watchdog driver is
only used on the Axiomtek SBC8360 single-board computer. This piece of
hardware is 32-bit x86 so the driver is useless beyond X86_32.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Add the LPAR variant of the diag 288 watchdog to the driver.
The only available action on timeout for LPAR is a PSW restart.
Signed-off-by: Philipp Hachtmann <phacht@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Converted the vmwatchdog driver to use the kernel's watchdog API.
Signed-off-by: Philipp Hachtmann <phacht@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The purpose of this single series of commits from Srivatsa S Bhat (with
a small piece from Gautham R Shenoy) touching multiple subsystems that use
CPU hotplug notifiers is to provide a way to register them that will not
lead to deadlocks with CPU online/offline operations as described in the
changelog of commit 93ae4f978c (CPU hotplug: Provide lockless versions
of callback registration functions).
The first three commits in the series introduce the API and document it
and the rest simply goes through the users of CPU hotplug notifiers and
converts them to using the new method.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQIcBAABCAAGBQJTQow2AAoJEILEb/54YlRxW4QQAJlYRDUzwFJzJzYhltQYuVR+
4D74XMtvXgoJfg3cwdSWvMKKpJZnA9BVN0f7Hcx9wYmgdexYUuHeZJmMNyc3S2+g
KjKBIsugvgmZhHbbLd6TJ6GBbhGT5JLt9VmSfL9zIkveInU1YHFUUqL/mxdHm4J0
BSGKjk2rN3waRJgmY+xfliFLtQjDKFwJpMuvrgtoUyfas3f4sIV43UNbqdvA/weJ
rzedxXOlKH/id4b56lj/4iIzcoL3mwvJJ7r6n0CEMsKv87z09kqR0O+69Tsq/cgs
j17CsvoJOmZGk3QTeKVMQWBsvk6aPoDu3zK83gLbQMt+qjOpSTbJLz/3HZw4/TrW
ss4nuZne1DLMGS+6hoxYbTP+6Ni//Kn+l/LrHc5jb7m1X3lMO4W2aV3IROtIE1rv
lEP1IG01NU4u9YwkVj1dyhrkSp8tLPul4SrUK8W+oNweOC5crjJV7vJbIPJgmYiM
IZN55wln0yVRtR4TX+rmvN0PixsInE8MeaVCmReApyF9pdzul/StxlBze5BKLSJD
cqo1kNPpsmdxoDucqUpQ/gSvy+IOl2qnlisB5PpV93sk7De6TFDYrGHxjYIW7jMf
StXwdCDDQhzd2Q8Kfpp895A1dbIl8rKtwA6bTU2eX+BfMVFzuMdT44cvosx1+UdQ
sWl//rg76nb13dFjvF+q
=SW7Q
-----END PGP SIGNATURE-----
Merge tag 'cpu-hotplug-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull CPU hotplug notifiers registration fixes from Rafael Wysocki:
"The purpose of this single series of commits from Srivatsa S Bhat
(with a small piece from Gautham R Shenoy) touching multiple
subsystems that use CPU hotplug notifiers is to provide a way to
register them that will not lead to deadlocks with CPU online/offline
operations as described in the changelog of commit 93ae4f978c ("CPU
hotplug: Provide lockless versions of callback registration
functions").
The first three commits in the series introduce the API and document
it and the rest simply goes through the users of CPU hotplug notifiers
and converts them to using the new method"
* tag 'cpu-hotplug-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (52 commits)
net/iucv/iucv.c: Fix CPU hotplug callback registration
net/core/flow.c: Fix CPU hotplug callback registration
mm, zswap: Fix CPU hotplug callback registration
mm, vmstat: Fix CPU hotplug callback registration
profile: Fix CPU hotplug callback registration
trace, ring-buffer: Fix CPU hotplug callback registration
xen, balloon: Fix CPU hotplug callback registration
hwmon, via-cputemp: Fix CPU hotplug callback registration
hwmon, coretemp: Fix CPU hotplug callback registration
thermal, x86-pkg-temp: Fix CPU hotplug callback registration
octeon, watchdog: Fix CPU hotplug callback registration
oprofile, nmi-timer: Fix CPU hotplug callback registration
intel-idle: Fix CPU hotplug callback registration
clocksource, dummy-timer: Fix CPU hotplug callback registration
drivers/base/topology.c: Fix CPU hotplug callback registration
acpi-cpufreq: Fix CPU hotplug callback registration
zsmalloc: Fix CPU hotplug callback registration
scsi, fcoe: Fix CPU hotplug callback registration
scsi, bnx2fc: Fix CPU hotplug callback registration
scsi, bnx2i: Fix CPU hotplug callback registration
...
These changes are mostly for ARM specific device drivers that either
don't have an upstream maintainer, or that had the maintainer ask
us to pick up the changes to avoid conflicts. A large chunk of this
are clock drivers (bcm281xx, exynos, versatile, shmobile), aside from
that, reset controllers for STi as well as a large rework of the
Marvell Orion/EBU watchdog driver are notable.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=u/FI
-----END PGP SIGNATURE-----
Merge tag 'drivers-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver changes from Arnd Bergmann:
"These changes are mostly for ARM specific device drivers that either
don't have an upstream maintainer, or that had the maintainer ask us
to pick up the changes to avoid conflicts.
A large chunk of this are clock drivers (bcm281xx, exynos, versatile,
shmobile), aside from that, reset controllers for STi as well as a
large rework of the Marvell Orion/EBU watchdog driver are notable"
* tag 'drivers-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (99 commits)
Revert "dts: socfpga: Add DTS entry for adding the stmmac glue layer for stmmac."
Revert "net: stmmac: Add SOCFPGA glue driver"
ARM: shmobile: r8a7791: Fix SCIFA3-5 clocks
ARM: STi: Add reset controller support to mach-sti Kconfig
drivers: reset: stih416: add softreset controller
drivers: reset: stih415: add softreset controller
drivers: reset: Reset controller driver for STiH416
drivers: reset: Reset controller driver for STiH415
drivers: reset: STi SoC system configuration reset controller support
dts: socfpga: Add sysmgr node so the gmac can use to reference
dts: socfpga: Add support for SD/MMC on the SOCFPGA platform
reset: Add optional resets and stubs
ARM: shmobile: r7s72100: fix bus clock calculation
Power: Reset: Generalize qnap-poweroff to work on Synology devices.
dts: socfpga: Update clock entry to support multiple parents
ARM: socfpga: Update socfpga_defconfig
dts: socfpga: Add DTS entry for adding the stmmac glue layer for stmmac.
net: stmmac: Add SOCFPGA glue driver
watchdog: orion_wdt: Use %pa to print 'phys_addr_t'
drivers: cci: Export CCI PMU revision
...
Pull main powerpc updates from Ben Herrenschmidt:
"This time around, the powerpc merges are going to be a little bit more
complicated than usual.
This is the main pull request with most of the work for this merge
window. I will describe it a bit more further down.
There is some additional cpuidle driver work, however I haven't
included it in this tree as it depends on some work in tip/timer-core
which Thomas accidentally forgot to put in a topic branch. Since I
didn't want to carry all of that tip timer stuff in powerpc -next, I
setup a separate branch on top of Thomas tree with just that cpuidle
driver in it, and Stephen has been carrying that in next separately
for a while now. I'll send a separate pull request for it.
Additionally, two new pieces in this tree add users for a sysfs API
that Tejun and Greg have been deprecating in drivers-core-next.
Thankfully Greg reverted the patch that removes the old API so this
merge can happen cleanly, but once merged, I will send a patch
adjusting our new code to the new API so that Greg can send you the
removal patch.
Now as for the content of this branch, we have a lot of perf work for
power8 new counters including support for our new "nest" counters
(also called 24x7) under pHyp (not natively yet).
We have new functionality when running under the OPAL firmware
(non-virtualized or KVM host), such as access to the firmware error
logs and service processor dumps, system parameters and sensors, along
with a hwmon driver for the latter.
There's also a bunch of bug fixes accross the board, some LE fixes,
and a nice set of selftests for validating our various types of copy
loops.
On the Freescale side, we see mostly new chip/board revisions, some
clock updates, better support for machine checks and debug exceptions,
etc..."
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (70 commits)
powerpc/book3s: Fix CFAR clobbering issue in machine check handler.
powerpc/compat: 32-bit little endian machine name is ppcle, not ppc
powerpc/le: Big endian arguments for ppc_rtas()
powerpc: Use default set of netfilter modules (CONFIG_NETFILTER_ADVANCED=n)
powerpc/defconfigs: Enable THP in pseries defconfig
powerpc/mm: Make sure a local_irq_disable prevent a parallel THP split
powerpc: Rate-limit users spamming kernel log buffer
powerpc/perf: Fix handling of L3 events with bank == 1
powerpc/perf/hv_{gpci, 24x7}: Add documentation of device attributes
powerpc/perf: Add kconfig option for hypervisor provided counters
powerpc/perf: Add support for the hv 24x7 interface
powerpc/perf: Add support for the hv gpci (get performance counter info) interface
powerpc/perf: Add macros for defining event fields & formats
powerpc/perf: Add a shared interface to get gpci version and capabilities
powerpc/perf: Add 24x7 interface headers
powerpc/perf: Add hv_gpci interface header
powerpc: Add hvcalls for 24x7 and gpci (Get Performance Counter Info)
sysfs: create bin_attributes under the requested group
powerpc/perf: Enable BHRB access for EBB events
powerpc/perf: Add BHRB constraint and IFM MMCRA handling for EBB
...
Anyone using a system based on an AMD Elan SC520 processor would be
building a dedicated kernel for it, so we can make the sc520_wdt
driver depend on MELAN. SC520_CPUFREQ already depends on MELAN so it
makes things more consistent. It also makes kernel configuration for
every other x86 user easier.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Using platform_driver_probe instead of platform_driver_register has
two benefits:
* The driver will fail to load if device probing fails.
* The probe function can be marked __init.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Using platform_driver_probe instead of platform_driver_register has
two benefits:
* The driver will fail to load if device probing fails.
* The probe function can be marked __init.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Using platform_driver_probe instead of platform_driver_register has
two benefits:
* The driver will fail to load if device probing fails.
* The probe function can be marked __init.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Using platform_driver_probe instead of platform_driver_register has
two benefits:
* The driver will fail to load if device probing fails.
* The probe function can be marked __init.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The watchdog's parent is iTCO_wdt (the platform device) not lpc_ich
(the PCI device.) Setting the parent right makes it much easier for
the user to figure out which driver/module is handling the watchdog
device node.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
On some hardware platforms, the it87_wdt watchdog resets the machine
despite the watchdog daemon running and writing to /dev/watchdog.
This is due to Consumer IR buffer underrun interrupts being used as
triggers to reset the timer. On some buggy hardware implementations
such as the iEi AFL-12A-N270 single-board computer, this method does
not work.
However, resetting the timer by writing its original timeout value in
its configuration register over and over again suppresses the unwanted
reboots.
Add a module option (nocir), 0 by default in order not to break existing
setups. Setting it to 1 enables the workaround.
Fixes bug #42801 <https://bugzilla.kernel.org/show_bug.cgi?id=42801>.
Tested primarily on Linux 3.5.7, applies cleanly on Linux 3.13.5.
Signed-off-by: Marc van der Wal <x0r+kernel@x0r.fr>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Use more the applicable ARCH_BCM_MOBILE option instead of ARCH_BCM as
dependency for bcm_kona_wdt.c.
Signed-off-by: Markus Mayer <markus.mayer@linaro.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Initializing clk to NULL as a reset/error condition does not
help as NULL is not an invalid condition w.r.t clk. Remove this
initialization altogether as there is no state retention.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The Allwinner A10 and A31 compatibles were following a slightly different
compatible patterns than the rest of the SoCs for historical reasons. Change
the compatibles to match the other pattern in the watchdog controller driver
for consistency.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
DT-enabled Dove will move over from ARCH_DOVE in mach-dove to MACH_DOVE in
mach-mvebu. As non-DT ARCH_DOVE will stay to rot for a while, add a new
DT-only MACH_DOVE Kconfig.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Fix the following checkpatch warnings and error:
WARNING: quoted string split across lines
WARNING: braces {} are not necessary for single statement blocks
WARNING: __initdata should be placed after ibmasr_id_table[]
WARNING: please, no space before tabs
ERROR: do not initialise statics to 0 or NULL
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Add a driver for the hardware watchdogs in NVIDIA Tegra SoCs (Tegra30 and
later). This driver will configure one watchdog timer that will reset the
system in the case of a watchdog timeout.
This driver binds to the nvidia,tegra30-timer device node and gets its
register base from there.
Signed-off-by: Andrew Chew <achew@nvidia.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Enable this driver for Zynq.
Move it to architecture independent Kconfig part.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Use of_property_read_u32 functions to clean probe function.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Use dev_ functions for printk messages.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Only one watchdog could be used by this driver.
Create driver private data structure and move there
all variables for one instance.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
no_timeout should be local variable because it is used
only in probe function.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Use devm_ helper function to simplify probe and error path.
Move ioremap to the beginning of probe function.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
control_status_reg is temp variables and should be
used locally by specific function.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
- Remove uneeded headers, fops functions
- Use xilinx_wdt prefix in start/stop/keepalive functions
and in new structures
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Variable "new_margin" is checked in the function watchdog_ioctl()
to be non-negative, so change its type to "int".
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Variable "wdt" is not used anywhere in the function sh_wdt_remove().
This patch removes this variable.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Variable "dummy" is not used anywhere in the function wdt_config().
This patch removes this variable.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Variable "hw_pre_value" is not used anywhere in the
function intel_scu_set_heartbeat().
This patch removes this variable.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch simplify functions indydog_start() and indydog_stop()
a bit and removes excess intermediate variable.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Field "default_ticks" is not used anywhere in the driver code.
This patch removes this field.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Use devm_ioremap_resource() in order to make the code simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Use devm_ioremap_resource() in order to make the code simpler,
and remove 'struct resource *mem' from 'struct omap_wdt_dev'
and omap_wdt_probe(), resplectively. because the 'mem' variables
are not used anymore. Also the redundant return value check of
platform_get_resource() is removed, because the value is checked
by devm_ioremap_resource().
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Use devm_ioremap_resource() in order to make the code simpler,
and remove redundant return value check of platform_get_resource()
because the value is checked by devm_ioremap_resource().
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Make 'ts72xx_wdt_pdev' static, because it is used only in this
file. It also fixes the following sparse warning.
warning: symbol 'ts72xx_wdt_pdev' was not declared. Should it be static?
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message. For example,
k.alloc and v.alloc failures use dump_stack().
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de> [for at32ap700x]
Acked-by: Lubomir Rintel <lkundrak@v3.sk> [for bcm2835]
Acked-by: Viresh Kumar <viresh.kumar@linaro.org> [for sp805_wdt]
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> [for ts72xx_wdt]
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Cc: linux-watchdog@vger.kernel.org
MPC8xx watchdog is enabled at startup by HW.
If the bootloader disables it, it cannot be reenabled.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Subsystems that want to register CPU hotplug callbacks, as well as perform
initialization for the CPUs that are already online, often do it as shown
below:
get_online_cpus();
for_each_online_cpu(cpu)
init_cpu(cpu);
register_cpu_notifier(&foobar_cpu_notifier);
put_online_cpus();
This is wrong, since it is prone to ABBA deadlocks involving the
cpu_add_remove_lock and the cpu_hotplug.lock (when running concurrently
with CPU hotplug operations).
Instead, the correct and race-free way of performing the callback
registration is:
cpu_notifier_register_begin();
for_each_online_cpu(cpu)
init_cpu(cpu);
/* Note the use of the double underscored version of the API */
__register_cpu_notifier(&foobar_cpu_notifier);
cpu_notifier_register_done();
Fix the watchdog code in octeon by using this latter form of callback
registration.
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This reverts commit 3978bdb4ed, now that
critical interrupts are properly supported on ppc64 booke.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Laurentiu Tudor <Laurentiu.Tudor@freescale.com>
Cc: Wim Van Sebroeck <wim@iguana.be>
Some new Atom's, eg Avoton and Bay Trail, have slightly different iTCO
functionality:
- The watchdog timer ticks at 1 second instead of .6 seconds
- Some 8 and 16-bit registers were combined into 32-bit registers
- Some registers were removed (DAT_IN, DAT_OUT, MESSAGE)
- The BOOT_STS field in TCO_STS was removed
- The NO_REBOOT bit is in the PMC area instead of GCS
Update the driver to support the above changes and bump the version to
1.11.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Tested-by: Rajat Jain <rajatjain@juniper.net>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
mvebu watchdog driver changes for v3.15 (incremental #2)
- remove warnings by using %pa for phys_addr_t
* tag 'mvebu-watchdog-3.15-2' of git://git.infradead.org/linux-mvebu:
watchdog: orion_wdt: Use %pa to print 'phys_addr_t'
Signed-off-by: Olof Johansson <olof@lixom.net>
When building an ARM multi_v7_defconfig with LPAE option selected we get the
following build warning:
drivers/watchdog/orion_wdt.c:272:2: warning: format '%x' expects argument of type 'unsigned int', but argument 4 has type 'phys_addr_t' [-Wformat=]
Fix it by using %pa to print 'phys_addr_t'.
Reported-by: Olof's autobuilder <build@lixom.net>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
- orion watchdog
- cleanup and extend driver to support Armada 370 and Armada XP
Depends:
- tags/irqchip-mvebu-fixes-3.14 (already pulled by tglx)
- both are based on v3.14-rc1
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=3VWF
-----END PGP SIGNATURE-----
Merge tag 'mvebu-watchdog-3.15' of git://git.infradead.org/linux-mvebu into next/drivers
mvebu watchdog driver changes for v3.15
- orion watchdog
- cleanup and extend driver to support Armada 370 and Armada XP
Depends:
- tags/irqchip-mvebu-fixes-3.14 (already pulled by tglx)
- both are based on v3.14-rc1
* tag 'mvebu-watchdog-3.15' of git://git.infradead.org/linux-mvebu:
watchdog: orion: Enable the build on ARCH_MVEBU
watchdog: orion: Add support for Armada 370 and Armada XP SoC
watchdog: orion: Add per-compatible watchdog start implementation
watchdog: orion: Add per-compatible clock initialization
watchdog: orion: Introduce per-compatible of_device_id data
watchdog: orion: Introduce an orion_watchdog device structure
watchdog: orion: Remove unneeded BRIDGE_CAUSE clear
watchdog: orion: Make RSTOUT register a separate resource
watchdog: orion: Handle the interrupt so it's properly acked
watchdog: orion: Make sure the watchdog is initially stopped
watchdog: orion: Remove unused macros
watchdog: orion: Use atomic access for shared registers
watchdog: orion: Add clock error handling
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
After adding support for Armada 370/XP SoC let's enable the build on
these platforms.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Wim Van Sebroeck <wim@iguana.be>
Tested-By: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Using the added infrastructure for handling SoC differences,
this commit adds support for the watchdog controller available
in Armada 370 and Armada XP SoCs.
Also, and because the AXP clock initialization uses of_clk_get_by_name,
this commit changes the orion clock initialization to use clk_get() and
adds a proper clk_put() on the common exit/error paths.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Wim Van Sebroeck <wim@iguana.be>
Tested-By: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
To handle differences between SoCs this commit adds per-compatible
string start() function for the watchdog kick-off. This is preparation
work and makes no functionality changes to the current driver.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Wim Van Sebroeck <wim@iguana.be>
Tested-By: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Following the introduction of the compatible-data field,
it's now possible to further abstract the clock initialization.
This will allow to support SoC with a different clock setup.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Wim Van Sebroeck <wim@iguana.be>
Tested-By: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This commit adds an orion_watchdog_data structure to hold compatible-data
information. This allows to remove the driver-wide definition and to
be able to add support for multiple compatible-strings in the future.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Wim Van Sebroeck <wim@iguana.be>
Tested-By: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
In order to prepare to support multiple compatible-strings, this
commit adds a device structure to hold the driver's state.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Wim Van Sebroeck <wim@iguana.be>
Tested-By: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
After adding the IRQ request, the BRIDGE_CAUSE bit should be cleared by the
bridge interrupt controller. There's no longer a need to do it in the watchdog
driver, so we can simply remove it.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Wim Van Sebroeck <wim@iguana.be>
Tested-By: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
In order to support other SoC, it's required to distinguish
the 'control' timer register, from the 'rstout' register
that enables system reset on watchdog expiration.
To prevent a compatibility break, this commit adds a fallback
to a hardcoded RSTOUT address.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Wim Van Sebroeck <wim@iguana.be>
Tested-By: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
DT-enabled plaforms, where the irqchip driver for the brigde interrupt
controller is available, can handle the watchdog IRQ properly. Therefore,
request the interrupt and add a dummy handler that merely calls panic().
This is done in order to have an initial 'ack' of the interruption,
which clears the watchdog state.
Furthermore, since some platforms don't have such IRQ, this commit
makes the interrupt specification optional.
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Wim Van Sebroeck <wim@iguana.be>
Tested-By: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Having the watchdog initially fully stopped is important to avoid
any spurious watchdog triggers, in case the registers are not in
its reset state.
If the watchdog rstout is enabled and the watchdog counter running,
this initial stop is not performed, to comply with the 'nowayout'
parameter.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Wim Van Sebroeck <wim@iguana.be>
Tested-By: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
These are not used anywhere so it's safe to remove them.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Wim Van Sebroeck <wim@iguana.be>
Tested-By: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Since the timer control register is shared with the clocksource driver,
use the recently introduced atomic_io_clear_set() to access such register.
Given the watchdog core already provides serialization for all the
watchdog ops, this commit allows to remove the spinlock entirely.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Wim Van Sebroeck <wim@iguana.be>
Tested-By: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This commit adds a check for clk_prepare_enable success and introduces
an error path to disable the clock properly.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Wim Van Sebroeck <wim@iguana.be>
Tested-By: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Most WDT driver modules return ENODEV during modprobe if
no valid device was found, but w83697hf_wdt returns EIO.
Let w83697hf_wdt return ENODEV.
Signed-off-by: Stanislav Kholmanskikh <stanislav.kholmanskikh@oracle.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
On archs like S390 or um this driver cannot build nor work.
Make it depend on HAS_IOMEM to bypass build failures.
drivers/built-in.o: In function `dw_wdt_drv_probe':
drivers/watchdog/dw_wdt.c:302: undefined reference to `devm_ioremap_resource'
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
If the watchdog has already triggered for whatever reason, it won't restart
unless the trigger is reset.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Major difference is that the watchdog control and counter registers
are different on both chips.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Instead of requiring the user to provide an IO address per module
parameter, auto-detect it as well as supported chips.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Try to reset the watchdog counter 4 or 2 times more often than actually
requested, to avoid spurious watchdog reset.
If this is not possible because of the min_heartbeat value, reset it at
the min_heartbeat period.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Use the min_heartbeat value instead of the calculated heartbeat value for
the first watchdog reset to avoid spurious watchdog reset.
Resetting the watchdog counter during init might lead to a watchdog fault
reset because the watchdog counter has to be running for at least
min_heartbeat.
Resetting the watchdog counter after heartbeat might lead to a watchdog
timeout reset because the watchdog counter is running for more than
max_heartbeat time.
Using min_heartbeat instead of heartbeat does not guarantee that the
watchdog won't trigger a reset, but at least it reduces the chances to be
in such a case.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Fix the secs_to_ticks macro in case 0 is passed as an argument.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The at91sam9 watchdog timer can only be configured once, and the current
implementation tries to configure it in a static way:
- 2 seconds timeout
- wdt restart every 500ms
If the timer has already been configured with different values, it returns an
error and do not create any watchdog device.
This is not critical if the watchdog is disabled, but if it has been enabled with
different timeout values it will lead to a SoC reset.
This patch series tries to address this issue by adapting the heartbeat value
according the WDT timer config:
- it first tries to configure the timer as requested.
- if it fails it fallbacks to the current config, adapting its heartbeat timer
to the needs
This patch series also move to a dynamically allocated at91wdt device instead
of the static instance.
It adds a new at91 wdt type: software. This new type make use of the at91 wdt
interrupt to trigger a software reboot.
Finally it adds several properties to the device tree bindings.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
mach-moxart lacks a separate register for reset; as a workaround,
add a function that can be hooked to arm_pm_restart.
Signed-off-by: Jonas Jensen <jonas.jensen@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Convert mpc8xxx_wdt.c to the new watchdog API.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
'sirfsoc_wdt_of_match' is always compiled in. Hence the
helper macro is not needed.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch is being submitted to output a general string when the panic comes
in that informs the user of the possible places to look for the source of the
NMI. Because various systems log the message in different places this would
give a single display of where to go look instead of code that acts on all
these different server names or IDs.
Signed-off-by: Thomas Mingarelli <thomas.mingarelli@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
There is nothing ARM specific in this driver, and we intend to use it on the
Xtensa architecture. Also, clk.h now includes stubs for !CONFIG_HAVE_CLK, so
the driver should build anyway.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Acked-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
We should set watchdog timer to be disabled in low power mode,
as there is no service running in background, otherwise, system
will reset unexpected.
Signed-off-by: Anson Huang <b20788@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
A good watchdog driver is supposed to report when it was responsible
for resetting the system. Implement this for the s3c2410, at least on
exynos5250 and exynos5420 where we already have a pointer to the PMU
registers to read the information.
Note that exynos4 SoCs also provide the reset status, but providing
that is left as an exercise for future changes and is not plumbed up
in this patch series. Also note the exynos4 SoCs don't appear to need
any PMU config, which is why this patch separates the concepts of
having PMU Registers vs. needing PMU Config.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Add device tree support for exynos5250 and 5420 SoCs and use syscon regmap interface
to configure AUTOMATIC_WDT_RESET_DISABLE and MASK_WDT_RESET_REQUEST registers of PMU
to mask/unmask enable/disable of watchdog in probe and s2r scenarios.
Signed-off-by: Leela Krishna Amudala <l.krishna@samsung.com>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The existing watchdog timeout worked OK but didn't deal with
rounding in an ideal way when dividing out all of its clocks.
Specifically if you had a timeout of 32 seconds and an input clock of
66666666, you'd end up setting a timeout of 31.9998 seconds and
reporting a timeout of 31 seconds.
Specifically DBG printouts showed:
s3c2410wdt_set_heartbeat: count=16666656, timeout=32, freq=520833
s3c2410wdt_set_heartbeat: timeout=32, divisor=255, count=16666656 (0000ff4f)
and the final timeout reported to the user was:
((count / divisor) * divisor) / freq
(0xff4f * 255) / 520833 = 31 (truncated from 31.9998)
the technically "correct" value is:
(0xff4f * 255) / (66666666.0 / 128) = 31.9998
By using "DIV_ROUND_UP" we can be a little more correct.
s3c2410wdt_set_heartbeat: count=16666688, timeout=32, freq=520834
s3c2410wdt_set_heartbeat: timeout=32, divisor=255, count=16666688 (0000ff50)
and the final timeout reported to the user:
(0xff50 * 255) / 520834 = 32
the technically "correct" value is:
(0xff50 * 255) / (66666666.0 / 128) = 32.0003
We'll use a DIV_ROUND_UP to solve this, generally erroring on the side
of reporting shorter values to the user and setting the watchdog to
slightly longer than requested:
* Round input frequency up to assume watchdog is counting faster.
* Round divisions by divisor up to give us extra time.
At the same time we can avoid a for loop by just doing the right math.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
On modern SoCs the watchdog timer is parented on a clock that doesn't
change every time we have a cpufreq change. That means we don't need
to constantly adjust the watchdog timer, so avoid registering for and
dealing with cpufreq transitions unless we've actually got
CONFIG_ARM_S3C24XX_CPUFREQ defined.
Note that this is more than just an optimization. The s3c2410
watchdog driver actually pats the watchdog on every CPU frequency
change. On modern systems these happen many times per second (even in
a system where "nothing" is happening). That effectively makes any
userspace watchdog program useless (the watchdog is constantly patted
by the kernel). If we need ARM_S3C24XX_CPUFREQ defined on a
multiplatform kernel we'll need to make sure that kernel supports
common clock and change this to user common clock framework.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch adds a watchdog driver for devices controlled through GPIO,
(Analog Devices ADM706, Maxim MAX823, National NE555 etc).
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The keystone arch uses the same IP watchdog, so add "ti,keystone-wdt"
compatible and correct identity.
The Keystone arch is using clocks in DT and source clock for watchdog
has to be specified, so add this to binding.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Currently, the davinci watchdog can be read while counting,
so we can add ability to report the remaining time before
the system will reboot.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Some SoCs, like Keystone 2, can support more than one WDT and each
watchdog device has to use it's own base address, clock source,
watchdog device, so add new davinci_wdt_device structure to hold
device data.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Guenter roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
To reduce code duplicate and increase code readability use WDT core
code to handle WDT interface.
Remove io_lock as the WDT core uses mutex to lock each wdt device.
Remove wdt_state as the WDT core tracks state with its own variable.
The watchdog_init_timeout() can read timeout value from timeout-sec
property if the passed value is out of bounds. The heartbeat is
initialized in next way. If heartbeat is not set thought module
parameter, try to read it's value from WDT node timeout-sec property.
If node has no one, use default value.
The heartbeat is hold in wdd->timeout by WDT core, so use it in
order to set timeout period.
Davinci WDT can't be stopped and once it's expired - it can be
rearmed only after hardware reset, that's why nowayout feature
is enforced.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This change introduces debugfs support for the BCM281xx watchdog driver.
Signed-off-by: Markus Mayer <markus.mayer@linaro.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This commit adds support for the watchdog timer used on the BCM281xx
family of SoCs.
Signed-off-by: Markus Mayer <markus.mayer@linaro.org>
Reviewed-by: Matt Porter <matt.porter@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
It is valid for a watchdog driver to have 0 for a "min" and "max"
timeout if the driver doesn't need the core to enforce the concepts of
min and max. The s3c2410_wdt driver is one such driver. Specifically
it can be hard for that driver to come up with a static "max" on all
platforms without a lot more information since the input clock on
S3C2410 and S3C2440 can change with DVFS.
As written, watchdog_init_timeout() will not ever read "timeout-sec"
on these drivers since watchdog_timeout_invalid() will _never_ return
true. Change to not consider a timeout_parm of 0 as valid even if
min/max aren't specified by the driver. Also handle the case when
there is no min/max and no "timeout-sec" property.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Don't use DEFINE_PCI_DEVICE_TABLE macro, because this macro
is not preferred.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Updates of SoC-near drivers and other driver updates that makes more sense to
take through our tree.
The largest part of this is a conversion of device registration for some
renesas shmobile/sh devices over to use resources. This has required
coordination with the corresponding arch/sh changes, and we've agreed
to merge the arch/sh changes through our tree.
Added in this branch is support for Trusted Foundations secure firmware,
which is what is used on many of the commercial Nvidia Tegra products
that are in the market, including the Nvidia Shield. The code is local
to arch/arm at this time since it's uncertain whether it will be shared
with arm64 longer-term, if needed we will refactor later.
A couple of new RTC drivers used on ARM boards, merged through our tree
on request by the RTC maintainer.
... plus a bunch of smaller updates across the board, gpio conversions
for davinci, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=JJlw
-----END PGP SIGNATURE-----
Merge tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM driver updates from Olof Johansson:
"Updates of SoC-near drivers and other driver updates that makes more
sense to take through our tree.
The largest part of this is a conversion of device registration for
some renesas shmobile/sh devices over to use resources. This has
required coordination with the corresponding arch/sh changes, and
we've agreed to merge the arch/sh changes through our tree.
Added in this branch is support for Trusted Foundations secure
firmware, which is what is used on many of the commercial Nvidia Tegra
products that are in the market, including the Nvidia Shield. The
code is local to arch/arm at this time since it's uncertain whether it
will be shared with arm64 longer-term, if needed we will refactor
later.
A couple of new RTC drivers used on ARM boards, merged through our
tree on request by the RTC maintainer.
... plus a bunch of smaller updates across the board, gpio conversions
for davinci, etc"
* tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (45 commits)
watchdog: davinci: rename platform driver to davinci-wdt
tty: serial: Limit msm_serial_hs driver to platforms that use it
mmc: msm_sdcc: Limit driver to platforms that use it
usb: phy: msm: Move mach dependent code to platform data
clk: versatile: fixup IM-PD1 clock implementation
clk: versatile: pass a name to ICST clock provider
ARM: integrator: pass parent IRQ to the SIC
irqchip: versatile FPGA: support cascaded interrupts from DT
gpio: davinci: don't create irq_domain in case of unbanked irqs
gpio: davinci: use chained_irq_enter/chained_irq_exit API
gpio: davinci: add OF support
gpio: davinci: remove unused variable intc_irq_num
gpio: davinci: convert to use irqdomain support.
gpio: introduce GPIO_DAVINCI kconfig option
gpio: davinci: get rid of DAVINCI_N_GPIO
gpio: davinci: use {readl|writel}_relaxed() instead of __raw_*
serial: sh-sci: Add OF support
serial: sh-sci: Add device tree bindings documentation
serial: sh-sci: Remove platform data mapbase and irqs fields
serial: sh-sci: Remove platform data scbrr_algo_id field
...
platform device name from generic "watchdog"
to something more specific.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=C9qR
-----END PGP SIGNATURE-----
Merge tag 'davinci-for-v3.14/watchdog' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into next/drivers
From Sekhar Nori:
This patch updates the davinci watchdog
platform device name from generic "watchdog"
to something more specific.
* tag 'davinci-for-v3.14/watchdog' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
watchdog: davinci: rename platform driver to davinci-wdt
Signed-off-by: Kevin Hilman <khilman@linaro.org>
As we switch to use the watchdog core which permits more than one
active watchdog in the system, rename platform driver to
"davinci-wdt" to be identifiable.
Acked-by: Wim Van Sebroeck <wim@iguana.be>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
CONFIG_USB_DEBUG is going away, and all of the other USB drivers no
longer rely on "debug" module parameters for debugging lines, so move
the pcwd_usb driver to use the dynamic debug infrastructure to be more
in line with the rest of the kernel.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Wim Van Sebroeck <wim@iguana.be>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
If loaded with isapnp = 0 the driver explodes. This is catching
people out now and then. What should happen in the working case is
a complete mystery and the code appears terminally confused, but we
can at least make the error path work properly.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Partially-Resolves-bug: https://bugzilla.kernel.org/show_bug.cgi?id=53991
After commit 487722cf2 (watchdog: Get rid of MODULE_ALIAS_MISCDEV
statements) the affected drivers no longer need to include miscdevice.h.
Only exception is rt2880_wdt.c which never needed it.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Use helper functions named similar to other drivers to access
superio registers.
Request memory region only when needed, and use request_muxed_region().
This lets other devices (hwmon, gpio) use the same region.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
There is no need to enable the watchdog device if it is already enabled.
Also, when enabling the watchdog device, only set the watchdog device
enable bit and do not touch other bits; depending on the chip type,
those bits may enable other functionality.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
It is unnecessary to enable the logical device and WDT0 each time
the watchdog is accessed. Do it only once during initialization.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
All OMAP IP blocks expect LE data, but CPU may operate in BE mode.
Need to use endian neutral functions to read/write h/w registers.
I.e instead of __raw_read[lw] and __raw_write[lw] functions code
need to use read[lw]_relaxed and write[lw]_relaxed functions.
If the first simply reads/writes register, the second will byteswap
it if host operates in BE mode.
Changes are trivial sed like replacement of __raw_xxx functions
with xxx_relaxed variant.
Signed-off-by: Victor Kamensky <victor.kamensky@linaro.org>
Signed-off-by: Taras Kondratiuk <taras.kondratiuk@linaro.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
As CSR SiRF is converted to multi platform CLOCK_TICK_RATE is a dummy
value that seems to match the right value is used.
(arch/arm/mach-prima2/include/mach/timex.h which defined CLOCK_TICK_RATE
to 1000000 was removed in commit cf82e0e (ARM: sirf: enable
multiplatform support); marco used the same file.)
To not depend on that dummy value use a local #define instead.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
We changed "buf" from being an array of 6 chars to being a pointer this
sizeof(buf) needs to be updated as well.
Fixes: 2ddb8089a7e5 ('watchdog: pcwd_usb: Use allocated buffer for usb_control_msg')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
In case of error, the function devm_request_and_ioremap() returns NULL
pointer not ERR_PTR(). Fix it by using devm_ioremap_resource() instead
of devm_request_and_ioremap().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
I just can't find any value in MODULE_ALIAS_MISCDEV(WATCHDOG_MINOR)
and MODULE_ALIAS_MISCDEV(TEMP_MINOR) statements.
Either the device is enumerated and the driver already has a module
alias (e.g. PCI, USB etc.) that will get the right driver loaded
automatically.
Or the device is not enumerated and loading its driver will lead to
more or less intrusive hardware poking. Such hardware poking should be
limited to a bare minimum, so the user should really decide which
drivers should be tried and in what order. Trying them all in
arbitrary order can't do any good.
On top of that, loading that many drivers at once bloats the kernel
log. Also many drivers will stay loaded afterward, bloating the output
of "lsmod" and wasting memory. Some modules (cs5535_mfgpt which gets
loaded as a dependency) can't even be unloaded!
If defining char-major-10-130 is needed then it should happen in
user-space.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Mike Frysinger <vapier.adi@gmail.com>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: Zwane Mwaikambo <zwane@arm.linux.org.uk>
Cc: Jim Cromie <jim.cromie@gmail.com>
timeout_to_regval() returns a valid error code. Might as well use it.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
usb_control_msg() must use a dma-capable buffer.
This fixes the following error reported by smatch:
drivers/watchdog/pcwd_usb.c:257 usb_pcwd_send_command() error: doing dma on the
stack (buf)
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Driver core clears the driver data to NULL after device_release
or on probe failure, so just remove it from here.
Driver core change:
"device-core: Ensure drvdata = NULL when no driver is bound"
(sha1: 0998d06310)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
On CSR SiRFprimaII and SiRFatlasVI, the 6th timer can act as a watchdog
timer when the Watchdog mode is enabled.
watchdog occur when TIMER watchdog counter matches the value software
pre-set, when this event occurs, the effect is the same as the system
software reset.
Signed-off-by: Xianglong Du <Xianglong.Du@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Cc: Romain Izard <romain.izard.pro@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
of_match_ptr() is a macro used to avoid undefined reference error if
CONFIG_OF is used to selectively compile in or out the
data structure. It is defined as follows:
#ifdef CONFIG_OF
#define of_match_ptr(ptr) ptr
#else
#define of_match_ptr(ptr) NULL
#endif
In the case of this series, none of the drivers use CONFIG_OF macro to
compile out the data structure (i.e., the data structure is always
defined).
Hence the use of of_match_ptr() does not make any sense. Thus removing
it to make the code look simpler for readability.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
There seems to be some confusion here which functions return positive
numbers and which return negative error codes.
copy_to_user() returns the number of bytes remaining to be copied but we
want to return -EFAULT.
The rest is just clean up. get_user() actually returns zero on success
and -EFAULT on error so we can preserve the error code. The
timeout_to_regval() function returns -EINVAL on failure, but we can
propogate that back instead of hardcoding -EINVAL ourselves.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
--
This patch adds a watchdog driver for the main hardware watchdog timer
found on MOXA ART SoCs.
The MOXA ART SoC provides one writable timer register, restarting
the hardware once it reaches zero. The register is auto decremented
every APB clock cycle.
Signed-off-by: Jonas Jensen <jonas.jensen@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Added __user annotation to fix the following sparse warnings.
Also, it makes 'kempld_prescaler' static because it is used
only in this file.
drivers/watchdog/kempld_wdt.c:70:11: warning: symbol 'kempld_prescaler' was not declared. Should it be static?
drivers/watchdog/kempld_wdt.c:364:23: warning: incorrect type in initializer (different address spaces)
drivers/watchdog/kempld_wdt.c:364:23: expected int const [noderef] <asn:1>*register __p
drivers/watchdog/kempld_wdt.c:364:23: got int *<noident>
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Enable auto loading by udev when imx2_wdt is compiled as a module.
Signed-off-by: Niels de Vos <ndevos@redhat.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This is necessary to make the driver work with platforms using the
common clock framework.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The dw_wdt only provides PM_SLEEP operations, so convert the driver
to use SIMPLE_DEV_PM_OPS instead of populating the struct manually.
This has the added effect of simplifying the CONFIG_PM ifdefs.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
usual for this cycle with lots of clean-up.
- Cross arch clean-up and consolidation of early DT scanning code.
- Clean-up and removal of arch prom.h headers. Makes arch specific
prom.h optional on all but Sparc.
- Addition of interrupts-extended property for devices connected to
multiple interrupt controllers.
- Refactoring of DT interrupt parsing code in preparation for deferred
probe of interrupts.
- ARM cpu and cpu topology bindings documentation.
- Various DT vendor binding documentation updates.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJSgPQ4AAoJEMhvYp4jgsXif28H/1WkrXq5+lCFQZF8nbYdE2h0
R8PsfiJJmAl6/wFgQTsRel+ScMk2hiP08uTyqf2RLnB1v87gCF7MKVaLOdONfUDi
huXbcQGWCmZv0tbBIklxJe3+X3FIJch4gnyUvPudD1m8a0R0LxWXH/NhdTSFyB20
PNjhN/IzoN40X1PSAhfB5ndWnoxXBoehV/IVHVDU42vkPVbVTyGAw5qJzHW8CLyN
2oGTOalOO4ffQ7dIkBEQfj0mrgGcODToPdDvUQyyGZjYK2FY2sGrjyquir6SDcNa
Q4gwatHTu0ygXpyphjtQf5tc3ZCejJ/F0s3olOAS1ahKGfe01fehtwPRROQnCK8=
=GCbY
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree updates from Rob Herring:
"DeviceTree updates for 3.13. This is a bit larger pull request than
usual for this cycle with lots of clean-up.
- Cross arch clean-up and consolidation of early DT scanning code.
- Clean-up and removal of arch prom.h headers. Makes arch specific
prom.h optional on all but Sparc.
- Addition of interrupts-extended property for devices connected to
multiple interrupt controllers.
- Refactoring of DT interrupt parsing code in preparation for
deferred probe of interrupts.
- ARM cpu and cpu topology bindings documentation.
- Various DT vendor binding documentation updates"
* tag 'devicetree-for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (82 commits)
powerpc: add missing explicit OF includes for ppc
dt/irq: add empty of_irq_count for !OF_IRQ
dt: disable self-tests for !OF_IRQ
of: irq: Fix interrupt-map entry matching
MIPS: Netlogic: replace early_init_devtree() call
of: Add Panasonic Corporation vendor prefix
of: Add Chunghwa Picture Tubes Ltd. vendor prefix
of: Add AU Optronics Corporation vendor prefix
of/irq: Fix potential buffer overflow
of/irq: Fix bug in interrupt parsing refactor.
of: set dma_mask to point to coherent_dma_mask
of: add vendor prefix for PHYTEC Messtechnik GmbH
DT: sort vendor-prefixes.txt
of: Add vendor prefix for Cadence
of: Add empty for_each_available_child_of_node() macro definition
arm/versatile: Fix versatile irq specifications.
of/irq: create interrupts-extended property
microblaze/pci: Drop PowerPC-ism from irq parsing
of/irq: Create of_irq_parse_and_map_pci() to consolidate arch code.
of/irq: Use irq_of_parse_and_map()
...
not compiled for ages, and recent versions of gcc for it are broken.
Remove support for it.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=V6n6
-----END PGP SIGNATURE-----
Merge tag 'h8300-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull h8300 platform removal from Guenter Roeck:
"The patch series has been in -next for more than one relase cycle. I
did get a number of Acks, and no objections.
H8/300 has been dead for several years, the kernel for it has not
compiled for ages, and recent versions of gcc for it are broken.
Remove support for it"
* tag 'h8300-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
CREDITS: Add Yoshinori Sato for h8300
fs/minix: Drop dependency on H8300
Drop remaining references to H8/300 architecture
Drop MAINTAINERS entry for H8/300
watchdog: Drop references to H8300 architecture
net/ethernet: Drop H8/300 Ethernet driver
net/ethernet: smsc9194: Drop conditional code for H8/300
ide: Drop H8/300 driver
Drop support for Renesas H8/300 (h8300) architecture
Commit b5b4bb3f6a (of: only include prom.h on sparc) removed implicit
includes of of_*.h headers by powerpc's prom.h. Some components were
missed in initial clean-up patch, so add the necessary includes to fix
powerpc builds.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Matt Mackall <mpm@selenic.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-ide@vger.kernel.org
Cc: linux-crypto@vger.kernel.org
mrst is used as common name to represent all intel_mid type
soc's. But moorsetwon is just one of the intel_mid soc. So
renamed them to use intel_mid.
This patch mainly renames the variables and related
functions that uses *mrst* prefix with *intel_mid*.
To ensure that there are no functional changes, I have compared
the objdump of related files before and after rename and found
the only difference is symbol and name changes.
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Link: http://lkml.kernel.org/r/1382049336-21316-6-git-send-email-david.a.cohen@linux.intel.com
Signed-off-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Following files contains code that is common to all intel mid
soc's. So renamed them as below.
mrst/mrst.c -> intel-mid/intel-mid.c
mrst/vrtc.c -> intel-mid/intel_mid_vrtc.c
mrst/early_printk_mrst.c -> intel-mid/intel_mid_vrtc.c
pci/mrst.c -> pci/intel_mid_pci.c
Also, renamed the corresponding header files and made changes
to the driver files that included these header files.
To ensure that there are no functional changes, I have compared
the objdump of renamed files before and after rename and found
that the only difference is file name change.
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Link: http://lkml.kernel.org/r/1382049336-21316-4-git-send-email-david.a.cohen@linux.intel.com
Signed-off-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
This driver has a section mismatch, for probe and remove functions,
leading to the following warning during the compilation.
WARNING: drivers/watchdog/built-in.o(.data+0x24): Section mismatch in
reference from the variable sunxi_wdt_driver to the function
.init.text:sunxi_wdt_probe()
The variable sunxi_wdt_driver references
the function __init sunxi_wdt_probe()
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
STAGE_CFG bits are defined as [5:4] bits. However, '(((x) & 0x30) << 4)'
handles [9:8] bits. Thus, it should be fixed in order to handle
[5:4] bits.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Calling the WDIOC_GETSTATUS & WDIOC_GETBOOTSTATUS and twice will cause a
interruptible deadlock.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch is to prevent hpwdt from loading on any auxilary iLO devices defined
after the initial (or main) iLO device. All auxilary iLO devices will have a
subsystem device ID set to 0x1979 in order for hpwdt to differentiate between
the two types.
Signed-off-by: Thomas Mingarelli <thomas.mingarelli@hp.com>
Tested-by: Lisa Mitchell <lisa.mitchell@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Powerpc is a mess of implicit includes by prom.h. Add the necessary
explicit includes to drivers in preparation of prom.h cleanup.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Grant Likely <grant.likely@linaro.org>
Pull watchdog updates from Wim Van Sebroeck:
- New watchdog driver for Allwinner A10/A13
- some devm_ioremap_resource simplifications
- a s3c2410_wdt change that removes the global variables
* git://www.linux-watchdog.org/linux-watchdog:
watchdog: s3c2410_wdt: simplify use of devm_ioremap_resource
watchdog: simplify platform_get_resource_byname/devm_ioremap_resource
watchdog: ts72xx_wdt: simplify use of devm_ioremap_resource
watchdog: nuc900_wdt.c: simplify use of devm_ioremap_resource
watchdog: sunxi: New watchdog driver for Allwinner A10/A13
watchdog: s3c2410_wdt: remove the global variables
We cannot assume that the inline assembler code always ends up in the same
file as the original C file. So make any assembler labels that are called
with "extern" by C global
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Cc: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove unneeded error handling on the result of a call to
platform_get_resource when the value is passed to devm_ioremap_resource.
Move the call to platform_get_resource adjacent to the call to
devm_ioremap_resource to make the connection between them more clear.
A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression pdev,res,n,e,e1;
expression ret != 0;
identifier l;
@@
- res = platform_get_resource(pdev, IORESOURCE_MEM, n);
... when != res
- if (res == NULL) { ... \(goto l;\|return ret;\) }
... when != res
+ res = platform_get_resource(pdev, IORESOURCE_MEM, n);
e = devm_ioremap_resource(e1, res);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Remove unneeded error handling on the result of a call to
platform_get_resource_byname when the value is passed to devm_ioremap_resource.
A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression pdev,res,e,e1;
expression ret != 0;
identifier l;
@@
res = platform_get_resource_byname(...);
- if (res == NULL) { ... \(goto l;\|return ret;\) }
e = devm_ioremap_resource(e1, res);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Remove unneeded error handling on the result of a call to
platform_get_resource when the value is passed to devm_ioremap_resource.
A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression pdev,res,n,e,e1;
expression ret != 0;
identifier l;
@@
- res = platform_get_resource(pdev, IORESOURCE_MEM, n);
... when != res
- if (res == NULL) { ... \(goto l;\|return ret;\) }
... when != res
+ res = platform_get_resource(pdev, IORESOURCE_MEM, n);
e = devm_ioremap_resource(e1, res);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Remove unneeded error handling on the result of a call to
platform_get_resource when the value is passed to devm_ioremap_resource.
A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression pdev,res,n,e,e1;
expression ret != 0;
identifier l;
@@
- res = platform_get_resource(pdev, IORESOURCE_MEM, n);
... when != res
- if (res == NULL) { ... \(goto l;\|return ret;\) }
... when != res
+ res = platform_get_resource(pdev, IORESOURCE_MEM, n);
e = devm_ioremap_resource(e1, res);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Wan Zongshun <mcuos.com@gmail.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch adds the driver for the watchdog found in the Allwinner A10 and
A13 SoCs. It has DT-support and uses the new watchdog framework.
Signed-off-by: Carlo Caione <carlo.caione@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch removes the global variables in the driver file and
group them into a structure.
Signed-off-by: Leela Krishna Amudala <l.krishna@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Pull MIPS updates from Ralf Baechle:
"MIPS updates:
- All the things that didn't make 3.10.
- Removes the Windriver PPMC platform. Nobody will miss it.
- Remove a workaround from kernel/irq/irqdomain.c which was there
exclusivly for MIPS. Patch by Grant Likely.
- More small improvments for the SEAD 3 platform
- Improvments on the BMIPS / SMP support for the BCM63xx series.
- Various cleanups of dead leftovers.
- Platform support for the Cavium Octeon-based EdgeRouter Lite.
Two large KVM patchsets didn't make it for this pull request because
their respective authors are vacationing"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (124 commits)
MIPS: Kconfig: Add missing MODULES dependency to VPE_LOADER
MIPS: BCM63xx: CLK: Add dummy clk_{set,round}_rate() functions
MIPS: SEAD3: Disable L2 cache on SEAD-3.
MIPS: BCM63xx: Enable second core SMP on BCM6328 if available
MIPS: BCM63xx: Add SMP support to prom.c
MIPS: define write{b,w,l,q}_relaxed
MIPS: Expose missing pci_io{map,unmap} declarations
MIPS: Malta: Update GCMP detection.
Revert "MIPS: make CAC_ADDR and UNCAC_ADDR account for PHYS_OFFSET"
MIPS: APSP: Remove <asm/kspd.h>
SSB: Kconfig: Amend SSB_EMBEDDED dependencies
MIPS: microMIPS: Fix improper definition of ISA exception bit.
MIPS: Don't try to decode microMIPS branch instructions where they cannot exist.
MIPS: Declare emulate_load_store_microMIPS as a static function.
MIPS: Fix typos and cleanup comment
MIPS: Cleanup indentation and whitespace
MIPS: BMIPS: support booting from physical CPU other than 0
MIPS: Only set cpu_has_mmips if SYS_SUPPORTS_MICROMIPS
MIPS: GIC: Fix gic_set_affinity infinite loop
MIPS: Don't save/restore OCTEON wide multiplier state on syscalls.
...
This patch is being created to use the UEFI bits in the type 219 SMBIOS
record in order to decide whether or not to execute BIOS code. This is a
better solution than to depend on the iCRU bit since not all future servers
will use iCRU.
Signed-off-by: Thomas Mingarelli <thomas.mingarelli@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
----
drivers/watchdog/hpwdt.c | 9 ++++++---
1 files changed, 6 insertions(+), 3 deletions(-)
In watchdog_ping(), 'start' is called automatically when 'ping' function call
is not configured.
Softdog driver has same handling in both cases - start and ping, so 'ping' OPS
can be removed.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch adds the driver for the watchdog devices found on MEN Mikro
Elektronik A21 VMEbus CPU Carrier Boards. It has DT-support and uses the
watchdog framework.
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@men.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The bits in BRIDGE_CAUSE are documented as RW0C - read, write 0 to
clear. If we read the register, mask off the watchdog bit, and
write it back, we're actually clearing every interrupt which wasn't
pending at the time we read the register - and that is racy.
Fix this to only write ~WATCHDOG_BIT to the register, which means
we write as zero only the watchdog bit.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The watchdog infrastructure in Dove is no different from that in
Orion5x or Kirkwood, so let's enable it for Dove. The only things
missing are a few register settings in Dove's bridge-regs.h.
Rather than duplicating the same register bit masks for the RSTOUTn_MASK
and BRIDGE_CAUSE registers, move the definitions into the watchdog
driver itself.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This adds a driver for watchdog timer hardware present on Broadcom BCM2835 SoC,
used in Raspberry Pi and Roku 2 devices.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Cc: linux-rpi-kernel@lists.infradead.org
Cc: linux-watchdog@vger.kernel.org
Cc: devicetree-discuss@lists.ozlabs.org
Interrupt request doesn't use the right API: The TWD watchdog uses a per-cpu
interrupt (usually interrupt #30), and the GIC configuration should flag it as
such. With this setup, request_irq() should fail, and the right API is
request_percpu_irq(), together with enable_percpu_irq()/disable_percpu_irq().
Nothing ensures the userspace ioctl() will end-up kicking the watchdog on the
right CPU.
There are no users of this driver since a long time and it makes more sense to
get rid of it as nobody is looking to fix it.
In case somebody wakes up after this has been removed and needs it, please
revert this driver and pick these updates (These were never pushed to mainline):
http://comments.gmane.org/gmane.linux.ports.arm.kernel/245998
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Watchdog 1.01.a is also compatible with 1.00.a.
Add the origin version to compatible list.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
- Remove reference for IP version
- Fix header coding style
- Remove notes which are visible from the code
- Fix driver license according to header
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Kernel has nice helpers to dump buffers.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
A watchdog device may be stopped from userspace using WDIOC_SETOPTIONS
ioctl and flag WDIOS_DISABLECARD. If the device is closed after this
operation, watchdog_release() is called and status bits checked for
stopping it. Besides, if the device has not been unregistered a critical
message "watchdog did not stop!" is printed, although the ioctl may have
successfully stopped it already.
Without the patch a user application sample code like this will successfully
stop the watchdog, but the kernel will output the message
"watchdog did not stop!":
wd_fd = open("/dev/watchdog", O_RDWR);
flags = WDIOS_DISABLECARD;
ioctl(wd_fd, WDIOC_SETOPTIONS, &flags);
close(wd_fd);
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
In preparation to switching the jz4740 clk driver to the common clk framework
make sure to pass the device to clk_get().
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Commit 0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) removes the need to set driver data field to
NULL.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Timo Kokkonen <timo.t.kokkonen@nokia.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Commit 0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) removes the need to set driver data field to
NULL.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_{get,set}_drvdata() with &pdev->dev,
so we can directly pass a struct platform_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_{get,set}_drvdata() with &pdev->dev,
so we can directly pass a struct platform_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Boris BREZILLON