Add cache flushing code to the SH-Mobile specific CPU hotplug
implementation. While at it, add a cpu mask to make sure the
cache flushing code is finished in platform_cpu_die() before
letting the SoC-specific code in shmobile_platform_cpu_kill()
proceed with turning off power.
Without this code CPU hotplug offline fails when cache is
enabled on Cortex-A9 based SoCs.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add the function shmobile_platform_kill_cpu() to allow
SoC specific code to tie in their CPU shutdown code.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Convert the low level SMP assembly code for SH-Mobile ARM
from using the INIT to the CPUINIT section. This unbreaks
onlining of CPUs using the CPU hotplug interface:
echo 1 > /sys/devices/system/cpu/cpu1/online
Without this fix the reset vector code used by CPU hotplug
will be freed as init section data and CPU cores cannot
be brought online.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add SCIF2 and SCIF4 pin configuration code to
the r8a7779 Marzen board.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add GPIO-only r8a7779 PFC support V2.
Only regular GPIOs are supported at this time. GPIO_FN are not
supported because they require variable bit width support in be
the shared pfc code.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Initial support for the r8a7779 SoC and the Marzen board (V2).
Only SCIF ports and the TMU are supported at this point.
To keep things simple only entity-mapped virt-to-phys mappings
are supported. This forces drivers and other SoC glue code to
make use of ioremap(). We cannot support early serial console
due to virtual address space collisions with the ARM kernel.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add PFC support for a 32-bit unlock register. Needed to
drive the r8a7779 PFC that comes with a funky PMMR register.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add support for variable config reg hardware by adding
the macro PINMUX_CFG_REG_VAR(). The width of each bitfield
needs to be passed to the macro, and the correct space must
be consumed by each bitfield in the enum table following the
macro. Data registers still need to have fixed bitfields.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add a helper function for shared config reg access
calculations. This allows us to reduce the amount
of duplicated code, and at the same time prepare
for a common place for future variable bitwidth
config reg support.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Update the way the PFC code is passing bitfield
selection between configure register functions.
Convert the code from using index only to bitfield
number and selected value. First step towards future
variable bitfield width support.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Introduce gpio_read_bit() for data register read access
and modify sh_gpio_get_value() to make use of the new
function instead of gpio_read_reg(). The purpose of
this change is to update the code to only use the
gpio_read_reg() function for config register access.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
A call to va_copy() should always be followed by a call to va_end() in
the same function. In kernel/autit.c::audit_log_vformat() this is not
always done. This patch makes sure va_end() is always called.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Eric Paris <eparis@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We leak in drivers/scsi/aacraid/commctrl.c::aac_send_raw_srb() :
We allocate memory:
...
struct user_sgmap* usg;
usg = kmalloc(actual_fibsize - sizeof(struct aac_srb)
+ sizeof(struct sgmap), GFP_KERNEL);
and then neglect to free it:
...
for (i = 0; i < usg->count; i++) {
u64 addr;
void* p;
if (usg->sg[i].count >
((dev->adapter_info.options &
AAC_OPT_NEW_COMM) ?
(dev->scsi_host_ptr->max_sectors << 9) :
65536)) {
rcode = -EINVAL;
goto cleanup;
... this 'goto' makes 'usg' go out of scope and leak the memory we
allocated.
Other exits properly kfree(usg), it's just here it is neglected.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
max1111.c: fix checkpatch warning
hwmon: (lm75) fix checkpatch warnings
hwmon: (lm80) fix checkpatch messages
hwmon: replaced strict_str* with kstr*
hwmon: (lm75) fix checkpatch warning
hwmon: (lm75) added error handling
hwmon: (ltc4261) set data->valid to 0 if error
hwmon: (f75375s) Add support for F75387SG/RG
hwmon: (f75375s) Disable setting DC fan control mode for F75373
hwmon: (f75375s) Initialize pwmX_mode and pwmX_enable if there is no platform data
hwmon: (f75375s) Fix value range for PWM modes
hwmon: (f75375s) Use standard sysfs attribute names
hwmon: (f75375s) Fix checkpatch errors and warnings
hwmon: (pmbus/zl6100) Only instantiate external temperature sensor if enabled
hwmon: (pmbus/zl6100) Add support for Ericsson BMR45[0,1] and BMR46[2,3,4]
hwmon: (pmbus/zl6100) Add support for ZL2005
hwmon: (pmbus/adm1275) Validate device ID
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap: (36 commits)
mfd: Clearing events requires event registers to be writable for da9052-core
mfd: Fix annotations in da9052-core
gpiolib: Mark da9052 driver broken
mfd: Declare da9052_regmap_config for the bus drivers
MFD: DA9052/53 MFD core module add SPI support v2
MFD: DA9052/53 MFD core module
regmap: Add irq_base accessor to regmap_irq
regmap: Allow drivers to reinitialise the register cache at runtime
regmap: Add trace event for successful cache reads
regmap: Allow regmap_update_bits() users to detect changes
regmap: Report if we actually handled an interrupt in regmap-irq
regmap: Fix rbtreee build when not using debugfs
regmap: Provide debugfs dump of the rbtree cache data
regmap: Do debugfs init before cache init
regmap: Suppress noop writes in regmap_update_bits()
regmap: Remove indexed cache type
regmap: Drop check whether a register is readable in regcache_read
regmap: Properly round cache_word_size
regmap: Add support for 10/14 register formating
regmap: Try cached read before checking if a hardware read is possible
...
Big change is new hot-replacement.
A slot in an array can hold 2 devices - one that
wants-replacement and one that is the replacement.
Once the replacement is built - either from the
original or (in the case of errors) from elsewhere,
the wants-replacement device will be removed.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)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=j00/
-----END PGP SIGNATURE-----
Merge tag 'md-3.3' of git://neil.brown.name/md
md update for 3.3
Big change is new hot-replacement.
A slot in an array can hold 2 devices - one that
wants-replacement and one that is the replacement.
Once the replacement is built - either from the
original or (in the case of errors) from elsewhere,
the wants-replacement device will be removed.
* tag 'md-3.3' of git://neil.brown.name/md: (36 commits)
md/raid1: Mark device want_replacement when we see a write error.
md/raid1: If there is a spare and a want_replacement device, start replacement.
md/raid1: recognise replacements when assembling arrays.
md/raid1: handle activation of replacement device when recovery completes.
md/raid1: Allow a failed replacement device to be removed.
md/raid1: Allocate spare to store replacement devices and their bios.
md/raid1: Replace use of mddev->raid_disks with conf->raid_disks.
md/raid10: If there is a spare and a want_replacement device, start replacement.
md/raid10: recognise replacements when assembling array.
md/raid10: Allow replacement device to be replace old drive.
md/raid10: handle recovery of replacement devices.
md/raid10: Handle replacement devices during resync.
md/raid10: writes should get directed to replacement as well as original.
md/raid10: allow removal of failed replacement devices.
md/raid10: preferentially read from replacement device if possible.
md/raid10: change read_balance to return an rdev
md/raid10: prepare data structures for handling replacement.
md/raid5: Mark device want_replacement when we see a write error.
md/raid5: If there is a spare and a want_replacement device, start replacement.
md/raid5: recognise replacements when assembling array.
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (53 commits)
Kconfig: acpi: Fix typo in comment.
misc latin1 to utf8 conversions
devres: Fix a typo in devm_kfree comment
btrfs: free-space-cache.c: remove extra semicolon.
fat: Spelling s/obsolate/obsolete/g
SCSI, pmcraid: Fix spelling error in a pmcraid_err() call
tools/power turbostat: update fields in manpage
mac80211: drop spelling fix
types.h: fix comment spelling for 'architectures'
typo fixes: aera -> area, exntension -> extension
devices.txt: Fix typo of 'VMware'.
sis900: Fix enum typo 'sis900_rx_bufer_status'
decompress_bunzip2: remove invalid vi modeline
treewide: Fix comment and string typo 'bufer'
hyper-v: Update MAINTAINERS
treewide: Fix typos in various parts of the kernel, and fix some comments.
clockevents: drop unknown Kconfig symbol GENERIC_CLOCKEVENTS_MIGR
gpio: Kconfig: drop unknown symbol 'CS5535_GPIO'
leds: Kconfig: Fix typo 'D2NET_V2'
sound: Kconfig: drop unknown symbol ARCH_CLPS7500
...
Fix up trivial conflicts in arch/powerpc/platforms/40x/Kconfig (some new
kconfig additions, close to removed commented-out old ones)
* 'pm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (76 commits)
PM / Hibernate: Implement compat_ioctl for /dev/snapshot
PM / Freezer: fix return value of freezable_schedule_timeout_killable()
PM / shmobile: Allow the A4R domain to be turned off at run time
PM / input / touchscreen: Make st1232 use device PM QoS constraints
PM / QoS: Introduce dev_pm_qos_add_ancestor_request()
PM / shmobile: Remove the stay_on flag from SH7372's PM domains
PM / shmobile: Don't include SH7372's INTCS in syscore suspend/resume
PM / shmobile: Add support for the sh7372 A4S power domain / sleep mode
PM: Drop generic_subsys_pm_ops
PM / Sleep: Remove forward-only callbacks from AMBA bus type
PM / Sleep: Remove forward-only callbacks from platform bus type
PM: Run the driver callback directly if the subsystem one is not there
PM / Sleep: Make pm_op() and pm_noirq_op() return callback pointers
PM/Devfreq: Add Exynos4-bus device DVFS driver for Exynos4210/4212/4412.
PM / Sleep: Merge internal functions in generic_ops.c
PM / Sleep: Simplify generic system suspend callbacks
PM / Hibernate: Remove deprecated hibernation snapshot ioctls
PM / Sleep: Fix freezer failures due to racy usermodehelper_is_disabled()
ARM: S3C64XX: Implement basic power domain support
PM / shmobile: Use common always on power domain governor
...
Fix up trivial conflict in fs/xfs/xfs_buf.c due to removal of unused
XBT_FORCE_SLEEP bit
* git://git.kernel.org/pub/scm/linux/kernel/git/steve/gfs2-3.0-nmw:
GFS2: local functions should be static
GFS2: We only need one ACL getting function
GFS2: Fix multi-block allocation
GFS2: decouple quota allocations from block allocations
GFS2: split function rgblk_search
GFS2: Fix up "off by one" in the previous patch
GFS2: move toward a generic multi-block allocator
GFS2: O_(D)SYNC support for fallocate
GFS2: remove vestigial al_alloced
GFS2: combine gfs2_alloc_block and gfs2_alloc_di
GFS2: Add non-try locks back to get_local_rgrp
GFS2: f_ra is always valid in dir readahead function
GFS2: Fix very unlikley memory leak in ACL xattr code
GFS2: More automated code analysis fixes
GFS2: Add readahead to sequential directory traversal
GFS2: Fix up REQ flags
* 'for-linus' of git://oss.sgi.com/xfs/xfs: (22 commits)
xfs: mark the xfssyncd workqueue as non-reentrant
xfs: simplify xfs_qm_detach_gdquots
xfs: fix acl count validation in xfs_acl_from_disk()
xfs: remove unused XBT_FORCE_SLEEP bit
xfs: remove XFS_QMOPT_DQSUSER
xfs: kill xfs_qm_idtodq
xfs: merge xfs_qm_dqinit_core into the only caller
xfs: add a xfs_dqhold helper
xfs: simplify xfs_qm_dqattach_grouphint
xfs: nest qm_dqfrlist_lock inside the dquot qlock
xfs: flatten the dquot lock ordering
xfs: implement lazy removal for the dquot freelist
xfs: remove XFS_DQ_INACTIVE
xfs: cleanup xfs_qm_dqlookup
xfs: cleanup dquot locking helpers
xfs: remove the sync_mode argument to xfs_qm_dqflush_all
xfs: remove xfs_qm_sync
xfs: make sure to really flush all dquots in xfs_qm_quotacheck
xfs: untangle SYNC_WAIT and SYNC_TRYLOCK meanings for xfs_qm_dqflush
xfs: remove the lid_size field in struct log_item_desc
...
Fix up trivial conflict in fs/xfs/xfs_sync.c
* 'for-linus2' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (165 commits)
reiserfs: Properly display mount options in /proc/mounts
vfs: prevent remount read-only if pending removes
vfs: count unlinked inodes
vfs: protect remounting superblock read-only
vfs: keep list of mounts for each superblock
vfs: switch ->show_options() to struct dentry *
vfs: switch ->show_path() to struct dentry *
vfs: switch ->show_devname() to struct dentry *
vfs: switch ->show_stats to struct dentry *
switch security_path_chmod() to struct path *
vfs: prefer ->dentry->d_sb to ->mnt->mnt_sb
vfs: trim includes a bit
switch mnt_namespace ->root to struct mount
vfs: take /proc/*/mounts and friends to fs/proc_namespace.c
vfs: opencode mntget() mnt_set_mountpoint()
vfs: spread struct mount - remaining argument of next_mnt()
vfs: move fsnotify junk to struct mount
vfs: move mnt_devname
vfs: move mnt_list to struct mount
vfs: switch pnode.h macros to struct mount *
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=CI17
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux-2.6
devicetree/next changes queued for v3.3 merge window
* tag 'devicetree-for-linus-20120104' of git://git.secretlab.ca/git/linux-2.6:
ARM: prom.h: Fix build error by removing unneeded header file
irq: check domain hwirq range for DT translate
dt: add empty of_get_node/of_put_node functions
of/pdt: fix section mismatch warning
i2c-designware: add OF binding support
dt/i2c: Enumerate some of the known trivial i2c devices
dt: reform for_each_property to for_each_property_of_node
ARM/of: allow *machine_desc.dt_compat to be const
of/base: Take NULL string into account for property with multiple strings
OF/device-tree: Add some entries to vendor-prefixes.txt
Fix up trivial add-add conflicts in include/linux/of.h
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=uyNO
-----END PGP SIGNATURE-----
Merge tag 'spi-for-linus' of git://git.secretlab.ca/git/linux-2.6
spi changes queued up for v3.3 merge window
* tag 'spi-for-linus-20120104' of git://git.secretlab.ca/git/linux-2.6:
spi: Fix device unregistration when unregistering the bus master
spi-topcliff-pch: Change company name OKI SEMICONDUCTOR to LAPIS Semiconductor
spi-topcliff-pch: Support new device LAPIS Semiconductor ML7831 IOH
spi/omap: Correct the error path
spi/omap: call pm_runtime_disable in error path and remove
spi/omap: Use a workqueue per omap2_mcspi controller
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=9ugo
-----END PGP SIGNATURE-----
Merge tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux-2.6
Changes queued in gpio/next for the start of the 3.3 merge window
* tag 'gpio-for-linus-20120104' of git://git.secretlab.ca/git/linux-2.6:
gpio: Add decode of WM8994 GPIO configuration
gpio: Convert GPIO drivers to module_platform_driver
gpio: Fix typo in comment in Samsung driver
gpio: Explicitly index samsung_gpio_cfgs
gpio: Add Linus Walleij as gpio co-maintainer
of: Add device tree selftests
of: create of_phandle_args to simplify return of phandle parsing data
gpio/powerpc: Eliminate duplication of of_get_named_gpio_flags()
gpio/microblaze: Eliminate duplication of of_get_named_gpio_flags()
gpiolib: output basic details and consolidate gpio device drivers
pch_gpio: Change company name OKI SEMICONDUCTOR to LAPIS Semiconductor
pch_gpio: Support new device LAPIS Semiconductor ML7831 IOH
spi/pl022: make the chip deselect handling thread safe
spi/pl022: add support for pm_runtime autosuspend
spi/pl022: disable the PL022 block when unused
spi/pl022: move device disable to workqueue thread
spi/pl022: skip default configuration before suspending
spi/pl022: fix build warnings
spi/pl022: only enable RX interrupts when TX is complete
* 'driver-core-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (73 commits)
arm: fix up some samsung merge sysdev conversion problems
firmware: Fix an oops on reading fw_priv->fw in sysfs loading file
Drivers:hv: Fix a bug in vmbus_driver_unregister()
driver core: remove __must_check from device_create_file
debugfs: add missing #ifdef HAS_IOMEM
arm: time.h: remove device.h #include
driver-core: remove sysdev.h usage.
clockevents: remove sysdev.h
arm: convert sysdev_class to a regular subsystem
arm: leds: convert sysdev_class to a regular subsystem
kobject: remove kset_find_obj_hinted()
m86k: gpio - convert sysdev_class to a regular subsystem
mips: txx9_sram - convert sysdev_class to a regular subsystem
mips: 7segled - convert sysdev_class to a regular subsystem
sh: dma - convert sysdev_class to a regular subsystem
sh: intc - convert sysdev_class to a regular subsystem
power: suspend - convert sysdev_class to a regular subsystem
power: qe_ic - convert sysdev_class to a regular subsystem
power: cmm - convert sysdev_class to a regular subsystem
s390: time - convert sysdev_class to a regular subsystem
...
Fix up conflicts with 'struct sysdev' removal from various platform
drivers that got changed:
- arch/arm/mach-exynos/cpu.c
- arch/arm/mach-exynos/irq-eint.c
- arch/arm/mach-s3c64xx/common.c
- arch/arm/mach-s3c64xx/cpu.c
- arch/arm/mach-s5p64x0/cpu.c
- arch/arm/mach-s5pv210/common.c
- arch/arm/plat-samsung/include/plat/cpu.h
- arch/powerpc/kernel/sysfs.c
and fix up cpu_is_hotpluggable() as per Greg in include/linux/cpu.h
Make reiserfs properly display mount options in /proc/mounts.
CC: reiserfs-devel@vger.kernel.org
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
If there are any inodes on the super block that have been unlinked
(i_nlink == 0) but have not yet been deleted then prevent the
remounting the super block read-only.
Reported-by: Toshiyuki Okajima <toshi.okajima@jp.fujitsu.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Tested-by: Toshiyuki Okajima <toshi.okajima@jp.fujitsu.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Add a new counter to the superblock that keeps track of unlinked but
not yet deleted inodes.
Do not WARN_ON if set_nlink is called with zero count, just do a
ratelimited printk. This happens on xfs and probably other
filesystems after an unclean shutdown when the filesystem reads inodes
which already have zero i_nlink. Reported by Christoph Hellwig.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Tested-by: Toshiyuki Okajima <toshi.okajima@jp.fujitsu.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Currently remouting superblock read-only is racy in a major way.
With the per mount read-only infrastructure it is now possible to
prevent most races, which this patch attempts.
Before starting the remount read-only, iterate through all mounts
belonging to the superblock and if none of them have any pending
writes, set sb->s_readonly_remount. This indicates that remount is in
progress and no further write requests are allowed. If the remount
succeeds set MS_RDONLY and reset s_readonly_remount.
If the remounting is unsuccessful just reset s_readonly_remount.
This can result in transient EROFS errors, despite the fact the
remount failed. Unfortunately hodling off writes is difficult as
remount itself may touch the filesystem (e.g. through load_nls())
which would deadlock.
A later patch deals with delayed writes due to nlink going to zero.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Tested-by: Toshiyuki Okajima <toshi.okajima@jp.fujitsu.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Keep track of vfsmounts belonging to a superblock. List is protected
by vfsmount_lock.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Tested-by: Toshiyuki Okajima <toshi.okajima@jp.fujitsu.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k: (21 commits)
m68k/mac: Make CONFIG_HEARTBEAT unavailable on Mac
m68k/serial: Remove references to obsolete serial config options
m68k/net: Remove obsolete IRQ_FLG_* users
m68k: Don't comment out syscalls used by glibc
m68k/atari: Move declaration of atari_SCC_reset_done to header file
m68k/serial: Remove references to obsolete CONFIG_SERIAL167
m68k/hp300: Export hp300_ledstate
m68k: Initconst section fixes
m68k/mac: cleanup macro case
mac_scsi: fix mac_scsi on some powerbooks
m68k/mac: fix powerbook 150 adb_type
m68k/mac: fix baboon irq disable and shutdown
m68k/mac: oss irq fixes
m68k/mac: fix nubus slot irq disable and shutdown
m68k/mac: enable via_alt_mapping on performa 580
m68k/mac: cleanup forward declarations
m68k/mac: cleanup mac_irq_pending
m68k/mac: cleanup mac_clear_irq
m68k/mac: early console
m68k/mvme16x: Add support for EARLY_PRINTK
...
Fix up trivial conflict in arch/m68k/Kconfig.debug due to new
EARLY_PRINTK config option addition clashing with movement of the
BOOTPARAM options.
* 'for-linus' of git://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-2.6-arm: (207 commits)
ARM: 7267/1: Remove BUILD_BUG_ON from asm/bug.h
ARM: 7269/1: mach-sa1100: fix sched_clock breakage
ARM: 7198/1: arm/imx6: add restart support for imx6q
ARM: restart: remove the now empty arch_reset()
ARM: restart: remove comments about adding code to arch_reset()
ARM: restart: lpc32xx & u300: remove unnecessary printk
ARM: restart: plat-samsung: remove plat/reset.h and s5p_reset_hook
ARM: restart: w90x900: use new restart hook
ARM: restart: Versatile Express: use new restart hook
ARM: restart: versatile: use new restart hook
ARM: restart: u300: use new restart hook
ARM: restart: tegra: use new restart hook
ARM: restart: spear: use new restart hook
ARM: restart: shark: use new restart hook
ARM: restart: sa1100: use new restart hook
ARM: 7252/1: restart: S5PV210: use new restart hook
ARM: 7251/1: restart: S5PC100: use new restart hook
ARM: 7250/1: restart: S5P64X0: use new restart hook
ARM: 7266/1: restart: S3C64XX: use new restart hook
ARM: 7265/1: restart: S3C24XX: use new restart hook
...
Fix up trivial conflict in arch/arm/mm/init.c due to removal of
memblock_init() clashing with the movement of the sorting of the meminfo
array.
* 'amba-modalias' of git://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-2.6-arm:
sound: aaci: Enable module alias autogeneration for AMBA drivers
watchdog: sp805: Enable module alias autogeneration for AMBA drivers
fbdev: amba: Enable module alias autogeneration for AMBA drivers
serial: pl011: Enable module alias autogeneration for AMBA drivers
serial: pl010: Enable module alias autogeneration for AMBA drivers
spi: pl022: Enable module alias autogeneration for AMBA drivers
rtc: pl031: Enable module alias autogeneration for AMBA drivers
rtc: pl030: Enable module alias autogeneration for AMBA drivers
mmc: mmci: Enable module alias autogeneration for AMBA drivers
input: ambakmi: Enable module alias autogeneration for AMBA drivers
gpio: pl061: Enable module alias autogeneration for AMBA drivers
dmaengine: pl330: Enable module alias autogeneration for AMBA drivers
dmaengine: pl08x: Enable module alias autogeneration for AMBA drivers
hwrng: nomadik: Enable module alias autogeneration for AMBA drivers
ARM: amba: Auto-generate AMBA driver module aliases during modpost
ARM: amba: Move definition of struct amba_id to mod_devicetable.h
Paul Mundt