When called because we have run out of vmap address space, we only need
to recover objects that have vmappings and not all.
v2: Start using is_vmalloc_addr()
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460113874-17366-5-git-send-email-chris@chris-wilson.co.uk
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
We now have two implementations for vmapping a whole object, one for
dma-buf and one for the ringbuffer. If we couple the mapping into the
obj->pages lifetime, then we can reuse an obj->mapping for both and at
the same time couple it into the shrinker. There is a third vmapping
routine in the cmdparser that maps only a range within the object, for
the time being that is left alone, but will eventually use these routines
in order to cache the mapping between invocations.
v2: Mark the failable kmalloc() as __GFP_NOWARN (vsyrjala)
v3: Call unpin_vmap from the right dmabuf unmapper
v4: Rename vmap to map as we don't wish to imply the type of mapping
involved, just that it contiguously maps the object into kernel space.
Add kerneldoc and lockdep annotations
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: Dave Gordon <david.s.gordon@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460113874-17366-4-git-send-email-chris@chris-wilson.co.uk
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
After we pin the ringbuffer into the GGTT, all error paths need to unpin
it again. Move this common step into one block, and make the unable to
iomap error code consistent (i.e. treat it as out of memory to avoid
confusing it with a invalid argument).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460113874-17366-3-git-send-email-chris@chris-wilson.co.uk
We only need the struct_mutex to manipulate the pages_pin_count on the
object, we do not need to hold our BKL when freeing the exported
scatterlist.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460113874-17366-2-git-send-email-chris@chris-wilson.co.uk
This is to fix a GPU hang seen with mid thread pre-emption
and pooled EUs.
v2. Use IS_BXT_REVID instead of IS_BROXTON and INTEL_REVID
v3. And use correct type for register addresses
Signed-off-by: Tim Gore <tim.gore@intel.com>
Reviewed-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458571049-854-1-git-send-email-tim.gore@intel.com
For BXT, description of polarities of PORT_PLL_REF_SEL
has been reversed for newer Gen9LP steppings according to the
recent update in Bspec. This bit now should be set for
"Non-SSC" mode for all Gen9LP starting from B0 stepping.
v2: Only B0 and newer stepping should be affected by this
change.
Signed-off-by: Dongwon Kim <dongwon.kim@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=94866
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458176773-26925-1-git-send-email-dongwon.kim@intel.com
Check functions are used by atomic to see if the new state will
be allowed. There's also a hw state checker which checks afterwards
that the committed state is correct. Rename it to hw state verifier
to reduce some confusion.
Suggested-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/56FB8785.8020506@linux.intel.com
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
The modeset state verifier no longer has full access to the hardware,
instead it should only verify affected crtc's.
Looking for disabled stuff can be verified immediately after all crtc
disables have completed, while each enabled crtc can be verified right
after being enabled.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458741487-23801-3-git-send-email-maarten.lankhorst@linux.intel.com
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
[mlankhorst: check -> verify]
This will make it easier to keep the crtc checker when atomic
commit is reworked for asynchronous commits. This prevents checking
crtc's that were not part of the state. It's safe to verify disabled
encoders, connectors and dpll's that are not part of the state,
because during modeset connection_mutex is held.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458741487-23801-2-git-send-email-maarten.lankhorst@linux.intel.com
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
[mlankhorst: Extend commit message and rename check to verify.]
When reading from the HWS page, we use barrier() to prevent the compiler
optimising away the read from the volatile (may be updated by the GPU)
memory address. This is more suited to READ_ONCE(); make it so.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460195877-20520-5-git-send-email-chris@chris-wilson.co.uk
Rather than call a function to compute the matching cachelines and
clflush them, just call the clflush *instruction* directly. We also know
that we can use the unpatched plain clflush rather than the clflushopt
alternative.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460195877-20520-4-git-send-email-chris@chris-wilson.co.uk
Only declare a missed interrupt if we find that the GPU is idle with
waiters and a hangcheck interval has passed in which no new user
interrupts have been raised.
v2: Clear the stuck interrupt marker between successful batches
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460195877-20520-3-git-send-email-chris@chris-wilson.co.uk
In order to simplify future patches, extract the
lazy_coherency optimisation our of the engine->get_seqno() vfunc into
its own callback.
v2: Rename the barrier to engine->irq_seqno_barrier to try and better
reflect that the barrier is only required after the user interrupt before
reading the seqno (to ensure that the seqno update lands in time as we
do not have strict seqno-irq ordering on all platforms).
Reviewed-by: Dave Gordon <david.s.gordon@intel.com> [#v2]
v3: Comments for hangcheck paranoia. Mika wanted to keep the extra
barrier inside the hangcheck, just in case. I can argue that it doesn't
provide a barrier against anything, but the side-effects of applying the
barrier may prevent a false declaration of a hung GPU.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460195877-20520-2-git-send-email-chris@chris-wilson.co.uk
In order to ensure seqno/irq coherency, we currently read a ring register.
The mmio transaction following the interrupt delays the inspection of
the seqno long enough for the MI_STORE_DWORD_IMM to update the CPU
cache. However, it is only the memory timing that is important for the
purposes of the delay, we do not need nor desire the extra forcewake.
v3: Update commentary
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com> [v2]
Link: http://patchwork.freedesktop.org/patch/msgid/1460195877-20520-1-git-send-email-chris@chris-wilson.co.uk
Currently for the case where there is enough space at the end of Ring
buffer for accommodating only the base request, the wrapround is done
immediately and as a result the base request gets added at the start
of Ring buffer. But there may not be enough free space at the beginning
to accommodate the base request, as before the wraparound, the wait was
effectively done for the reserved_size free space from the start of
Ring buffer. In such a case there is a potential of Ring buffer overflow,
the instructions at the head of Ring (ACTHD) can get overwritten.
Since the base request can fit in the remaining space, there is no need
to wraparound immediately. The wraparound will anyway happen later when
the reserved part starts getting used.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Akash Goel <akash.goel@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1457688402-10411-1-git-send-email-akash.goel@intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@vger.kernel.org
Having fixed the tracking of the engine's last_submitted_seqno, we can
now rely on it for detecting when the engine is idle (and not have to
touch the requests pointer).
Testcase: igt/gem_exec_whisper
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460010558-10705-9-git-send-email-chris@chris-wilson.co.uk
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Seal the request and mark it as pending execution before we submit it to
hardware. We assume that the actual submission cannot fail (that
guarantee is provided by preallocating space in the request for the
submission). As we may inspect this state without holding any locks
during hangcheck we should apply a barrier to ensure that we do
not see a more recent value in the HWS than we are tracking.
Based on a patch by Mika Kuoppala.
Suggested-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460010558-10705-8-git-send-email-chris@chris-wilson.co.uk
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
When we change the current seqno, we also need to remember to reset the
last_submitted_seqno for the engine.
Testcase: igt/gem_exec_whisper
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460010558-10705-7-git-send-email-chris@chris-wilson.co.uk
An oversight is that when we wrap the seqno, we need to reset the hw
semaphore counters to 0. We did this for gen6 and gen7 and forgot to do
so for the new implementation required for gen8 (legacy).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460010558-10705-6-git-send-email-chris@chris-wilson.co.uk
Since we are setting engine local values that are tied to the hardware,
move it out of i915_gem_init_seqno() into the intel_ring_init_seqno()
backend, next to where the other hw semaphore registers are written.
v2: Make the explanatory comment about always resetting the semaphores to
0 irrespective of the value of the reset seqno.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460010558-10705-4-git-send-email-chris@chris-wilson.co.uk
We only use drm_i915_private within the function, so delete the unneeded
drm_device local.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460010558-10705-3-git-send-email-chris@chris-wilson.co.uk
After the GPU reset and we discard all of the incomplete requests, mark
the GPU as having advanced to the last_submitted_seqno (as having
completed the requests and ready for fresh work). The impact of this is
negligible, as all the requests will be considered completed by this
point, it just brings the HWS into line with expectations for external
viewers.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460010558-10705-2-git-send-email-chris@chris-wilson.co.uk
It's useful to look at the last seqno submitted on a particular engine
and compare it against the HWS value to check for irregularities.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460010558-10705-1-git-send-email-chris@chris-wilson.co.uk
At BXT DSI, PIPE registers are inactive. So we can't get the
PIPE's mode parameters from them. The possible option is
retriving them from the PORT registers.
The required changes are added for BXT in intel_dsi_get_config
(encoder->get_config).
v2: Addressed the Jani's comments
-removed the redundant call to encoder->get_config
-read bpp from port register
-removed retrival of src_size from encoder->get_config
v3: pipe_config->pipe_bpp is fixed
Jani's review comments addressed:
Few horizontal timing parameters dropped from the patch to make
progress, as there seems to be some disagreement on
best/feasible/possible options.
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Previously Reviewed at: https://lists.freedesktop.org/archives/intel-gfx/2016-April/091737.html
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460019967-26501-2-git-send-email-ramalingam.c@intel.com
Define and store the pad base offset in the array, and reference the
pconf0 and padval registers through macros. Add VLV prefixes to
macros. Use spec nomenclature for pconf0 and padval.
v2: Address Ville's review comments, squash another patch here.
v3: Use the names Ville dug up in the specs.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/34932140b78a3de7f825c78380a08c930694651b.1459884518.git.jani.nikula@intel.com
dev_priv is what the macro works hard to extract, pass it directly.
> sed 's/\([A-Z].*(dev_priv\)->dev)/\1)/g'
v2:
- Include all wrapper macros too (Chris)
v3:
- Include sed cmdline (Chris)
v4:
- Break long line
- Rebase
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460016485-8089-1-git-send-email-joonas.lahtinen@linux.intel.com
According to Chris, use of i915_vm_to_ppgtt is visible in benchmark
unless WARN_ON is removed, so lets get rid of it.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reported-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> (v1)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Looks much better without container_of everywhere.
v2:
- In i915_gem_restore_gtt_mappings too (Chris)
v3:
- Do not cause WARN by calling on non PPGTT object (Chris)
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
intel_update_max_cdclk() doesn't have a switch case for Broxton, so
dev_priv->max_cdclk_freq gets set to whatever clock frequency we're
currently running at (e.g., 144 MHz) rather than the true maximum. This
causes our max dotclock to also be set too low and in turn leads mode
verification to reject perfectly valid modes while loading EDID firmware
blobs.
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459892239-14041-1-git-send-email-matthew.d.roper@intel.com
This patch sets the invert bit for hpd detection for each port
based on VBT configuration. Since each AOB can be designed to
depend on invert bit or not, it is expected if an AOB requires
invert bit, the user will set respective bit in VBT.
v2: Separated VBT parsing from the rest of the logic. (Jani)
v3: Moved setting invert bit logic to bxt_hpd_irq_setup()
and changed its logic to avoid looping twice. (Ville)
v4: Changed the logic to mask out the bits first and then
set them to remove need of temporary variable. (Ville)
v5: Moved defines to existing set of defines for the register
and added required breaks. (Ville)
Signed-off-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Shubhangi Shrivastava <shubhangi.shrivastava@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[Jani: fixed some checkpatch noise, added kernel-doc.]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459420907-11383-2-git-send-email-shubhangi.shrivastava@intel.com
This patch adds new fields that are not yet added in drm code
in child devices struct
Signed-off-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Shubhangi Shrivastava <shubhangi.shrivastava@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459420907-11383-1-git-send-email-shubhangi.shrivastava@intel.com
Currently we set the initial GPU frequency to min_freq_softlimit
on gen9, and to efficient_freq on VLV/CHV. On all the other platforms
we set it to idle_freq. Let's use idle_freq across the board to make
sure we don't waste power. This is especially relevant for VLV since
Vnn won't drop to minimum unless the GPU is at the minimum frequency.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1457120584-26080-3-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Extract the GPLL reference frequency from CCK and use it in the
GPU freq<->opcode conversions on VLV/CHV. This eliminates all the
assumptions we have about which divider is used for which czclk
frequency.
Note that unlike most clocks from CCK, the GPLL ref clock is a divided
down version of the CZ clock rather than the HPLL clock. CZ clock itself
is a divided down version of the HPLL clock though, so in effect it just
gets divided down twice.
While at it, throw in a few comments explaining the remaining constants
for anyone who later wants to compare this to the spreadsheets.
v2: Add slow/fast notes for CHV clocks (Imre)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1457120584-26080-2-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com> (v1)
After a suspend-resume cycle, the resumed kernel has no idea what the
booted kernel may have done to the GuC before replacing itself with the
resumed image. In particular, it may have already loaded the GuC with
firmware, which will then cause this kernel's attempt to (re)load the
firmware to fail (GuC program memory is write-once!). The symptoms
(GuC firmware reload fails after hibernation) are further described
in the Bugzilla reference below.
So let's *always* reset the GuC just before (re)loading the firmware;
the hardware should then be in a well-known state, and we may even
avoid some of the issues arising from unpredictable timing.
Also added some more fields & values to the definition of the GUC_STATUS
register, which is the key diagnostic indicator if the GuC load fails.
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Cc: Alex Dai <yu.dai@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=94390
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Due to timing issues in the HW, some of the status bits required for GuC
authentication occasionally don't get set; when that happens, the GuC
cannot be initialized and we will be left with a wedged GPU. The W/A
suggested is to perform a soft reset of the GuC and attempt to reload
the F/W again for few times before giving up.
As the failure is dependent on timing, tests performed by triggering
manual full gpu reset (i915_wedged) showed that we could sometimes hit
this after several thousand iterations, but sometimes tests ran even
longer without any issues. Reset and reload mechanism proved helpful
when we indeed hit f/w load failure, so it is better to include this
to improve driver stability.
This change implements the following WAs,
WaEnableuKernelHeaderValidFix:skl,bxt
WaEnableGuCBootHashCheckNotSet:skl,bxt
Signed-off-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Alex Dai <yu.dai@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Both the oom and vmap notifier callbacks have a loop to acquire the
struct_mutex and set the device as uninterruptible, within a certain
time. Refactor the common code into a pair of functions.
Suggested-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459848145-24042-1-git-send-email-chris@chris-wilson.co.uk
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
If the core runs out of vmap address space, it will call a notifier in
case any driver can reap some of its vmaps. As i915.ko is possibily
holding onto vmap address space that could be recovered, hook into the
notifier chain and try and reap objects holding onto vmaps.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Roman Pen <r.peniaev@gmail.com>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: linux-mm@kvack.org
Cc: linux-kernel@vger.kernel.org
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kahola <mika.kahola@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459777603-23618-4-git-send-email-chris@chris-wilson.co.uk
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
vmaps are temporary kernel mappings that may be of long duration.
Reusing a vmap on an object is preferrable for a driver as the cost of
setting up the vmap can otherwise dominate the operation on the object.
However, the vmap address space is rather limited on 32bit systems and
so we add a notification for vmap pressure in order for the driver to
release any cached vmappings.
The interface is styled after the oom-notifier where the callees are
passed a pointer to an unsigned long counter for them to indicate if they
have freed any space.
v2: Guard the blocking notifier call with gfpflags_allow_blocking()
v3: Correct typo in forward declaration and move to head of file
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Roman Peniaev <r.peniaev@gmail.com>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: linux-mm@kvack.org
Cc: linux-kernel@vger.kernel.org
Acked-by: Andrew Morton <akpm@linux-foundation.org> # for inclusion via DRM
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459777603-23618-3-git-send-email-chris@chris-wilson.co.uk
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Since we only attempt to purge an object if can_release_pages() report
true, we should also only add it to the count of potential recoverable
pages when can_release_pages() is true.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Akash Goel <akash.goel@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459777603-23618-2-git-send-email-chris@chris-wilson.co.uk
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Doing a lot of work in the interrupt handler introduces huge
latencies to the system as a whole.
Most dramatic effect can be seen by running an all engine
stress test like igt/gem_exec_nop/all where, when the kernel
config is lean enough, the whole system can be brought into
multi-second periods of complete non-interactivty. That can
look for example like this:
NMI watchdog: BUG: soft lockup - CPU#0 stuck for 23s! [kworker/u8:3:143]
Modules linked in: [redacted for brevity]
CPU: 0 PID: 143 Comm: kworker/u8:3 Tainted: G U L 4.5.0-160321+ #183
Hardware name: Intel Corporation Broadwell Client platform/WhiteTip Mountain 1
Workqueue: i915 gen6_pm_rps_work [i915]
task: ffff8800aae88000 ti: ffff8800aae90000 task.ti: ffff8800aae90000
RIP: 0010:[<ffffffff8104a3c2>] [<ffffffff8104a3c2>] __do_softirq+0x72/0x1d0
RSP: 0000:ffff88014f403f38 EFLAGS: 00000206
RAX: ffff8800aae94000 RBX: 0000000000000000 RCX: 00000000000006e0
RDX: 0000000000000020 RSI: 0000000004208060 RDI: 0000000000215d80
RBP: ffff88014f403f80 R08: 0000000b1b42c180 R09: 0000000000000022
R10: 0000000000000004 R11: 00000000ffffffff R12: 000000000000a030
R13: 0000000000000082 R14: ffff8800aa4d0080 R15: 0000000000000082
FS: 0000000000000000(0000) GS:ffff88014f400000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007fa53b90c000 CR3: 0000000001a0a000 CR4: 00000000001406f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Stack:
042080601b33869f ffff8800aae94000 00000000fffc2678 ffff88010000000a
0000000000000000 000000000000a030 0000000000005302 ffff8800aa4d0080
0000000000000206 ffff88014f403f90 ffffffff8104a716 ffff88014f403fa8
Call Trace:
<IRQ>
[<ffffffff8104a716>] irq_exit+0x86/0x90
[<ffffffff81031e7d>] smp_apic_timer_interrupt+0x3d/0x50
[<ffffffff814f3eac>] apic_timer_interrupt+0x7c/0x90
<EOI>
[<ffffffffa01c5b40>] ? gen8_write64+0x1a0/0x1a0 [i915]
[<ffffffff814f2b39>] ? _raw_spin_unlock_irqrestore+0x9/0x20
[<ffffffffa01c5c44>] gen8_write32+0x104/0x1a0 [i915]
[<ffffffff8132c6a2>] ? n_tty_receive_buf_common+0x372/0xae0
[<ffffffffa017cc9e>] gen6_set_rps_thresholds+0x1be/0x330 [i915]
[<ffffffffa017eaf0>] gen6_set_rps+0x70/0x200 [i915]
[<ffffffffa0185375>] intel_set_rps+0x25/0x30 [i915]
[<ffffffffa01768fd>] gen6_pm_rps_work+0x10d/0x2e0 [i915]
[<ffffffff81063852>] ? finish_task_switch+0x72/0x1c0
[<ffffffff8105ab29>] process_one_work+0x139/0x350
[<ffffffff8105b186>] worker_thread+0x126/0x490
[<ffffffff8105b060>] ? rescuer_thread+0x320/0x320
[<ffffffff8105fa64>] kthread+0xc4/0xe0
[<ffffffff8105f9a0>] ? kthread_create_on_node+0x170/0x170
[<ffffffff814f351f>] ret_from_fork+0x3f/0x70
[<ffffffff8105f9a0>] ? kthread_create_on_node+0x170/0x170
I could not explain, or find a code path, which would explain
a +20 second lockup, but from some instrumentation it was
apparent the interrupts off proportion of time was between
10-25% under heavy load which is quite bad.
When a interrupt "cliff" is reached, which was >~320k irq/s on
my machine, the whole system goes into a terrible state of the
above described multi-second lockups.
By moving the GT interrupt handling to a tasklet in a most
simple way, the problem above disappears completely.
Testing the effect on sytem-wide latencies using
igt/gem_syslatency shows the following before this patch:
gem_syslatency: cycles=1532739, latency mean=416531.829us max=2499237us
gem_syslatency: cycles=1839434, latency mean=1458099.157us max=4998944us
gem_syslatency: cycles=1432570, latency mean=2688.451us max=1201185us
gem_syslatency: cycles=1533543, latency mean=416520.499us max=2498886us
This shows that the unrelated process is experiencing huge
delays in its wake-up latency. After the patch the results
look like this:
gem_syslatency: cycles=808907, latency mean=53.133us max=1640us
gem_syslatency: cycles=862154, latency mean=62.778us max=2117us
gem_syslatency: cycles=856039, latency mean=58.079us max=2123us
gem_syslatency: cycles=841683, latency mean=56.914us max=1667us
Showing a huge improvement in the unrelated process wake-up
latency. It also shows an approximate halving in the number
of total empty batches submitted during the test. This may
not be worrying since the test puts the driver under
a very unrealistic load with ncpu threads doing empty batch
submission to all GPU engines each.
Another benefit compared to the hard-irq handling is that now
work on all engines can be dispatched in parallel since we can
have up to number of CPUs active tasklets. (While previously
a single hard-irq would serially dispatch on one engine after
another.)
More interesting scenario with regards to throughput is
"gem_latency -n 100" which shows 25% better throughput and
CPU usage, and 14% better dispatch latencies.
I did not find any gains or regressions with Synmark2 or
GLbench under light testing. More benchmarking is certainly
required.
v2:
* execlists_lock should be taken as spin_lock_bh when
queuing work from userspace now. (Chris Wilson)
* uncore.lock must be taken with spin_lock_irq when
submitting requests since that now runs from either
softirq or process context.
v3:
* Expanded commit message with more testing data;
* converted missed locking sites to _bh;
* added execlist_lock comment. (Chris Wilson)
v4:
* Mention dispatch parallelism in commit. (Chris Wilson)
* Do not hold uncore.lock over MMIO reads since the block
is already serialised per-engine via the tasklet itself.
(Chris Wilson)
* intel_lrc_irq_handler should be static. (Chris Wilson)
* Cancel/sync the tasklet on GPU reset. (Chris Wilson)
* Document and WARN that tasklet cannot be active/pending
on engine cleanup. (Chris Wilson/Imre Deak)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Imre Deak <imre.deak@intel.com>
Testcase: igt/gem_exec_nop/all
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=94350
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1459768316-6670-1-git-send-email-tvrtko.ursulin@linux.intel.com
Chris Wilson