Add an SPMI regulator driver for Qualcomm's PM8841, PM8941, and
PM8916 PMICs. This driver is based largely on code from
codeaurora.org[1].
[1] https://www.codeaurora.org/cgit/quic/la/kernel/msm-3.10/tree/drivers/regulator/qpnp-regulator.c?h=msm-3.10
Cc: David Collins <collinsd@codeaurora.org>
Cc: <devicetree@vger.kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add BUCK and LDO regulator driver support for DA9062
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The GPIO subsystem provides dummy GPIO consumer functions if GPIOLIB is
not enabled. Hence drivers that depend on GPIOLIB, but use GPIO consumer
functionality only, can still be compiled if GPIOLIB is not enabled.
Relax the dependency on GPIOLIB if COMPILE_TEST is enabled, where
appropriate.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds new regulator driver to support max77843
MFD(Multi Function Device) chip`s regulators.
The Max77843 has two voltage regulators for USB safeout.
Signed-off-by: Jaewon Kim <jaewon02.kim@samsung.com>
Signed-off-by: Beomho Seo <beomho.seo@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The main thing this time around is support for suspend mode
configuration from DT which will enable some very useful power savings
on systems where we can't rely on the bootloader configuration. We
still don't really support dynamic configuration of this at runtime,
that may come later if there is any demand.
- Support for specifying the target regulation mode and voltage during
system suspend via DT, enabling power savings in that mode.
- Reduce the default verbosity of the logging on boot, improving boot
times especially for systems with very large numbers of regulators.
- Lots of cleanups and fixes for Maxim PMIC drivers.
- New driver for Richtek RT5033.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUhaLEAAoJECTWi3JdVIfQMIEH/0n/0TJngSaoifV72PCkICdx
GbNs2bUkjuNAbYw6S6xmbA6MYPEllGiFnmJPRjV41qf0a1TTG/vam3fjeaBao7En
DxEBsz22iuBM4wmOSEKTsDtTRuiX170cqKKWZ4ugFo/uaDinueW2tz0Uzvz05or5
bSxT8hbeYerNksb13mn7OjW8r0rCE24w1K669MZgwp0uuIY+NKUTnwT4TqMzDo5c
OT4RQ2XZAQOhOfqS4VTR07Ab8PzGQd4zzmTYljqd2MKL7ubKz41vNSnGHwPdrTH1
FeQ9Q/JZl0W6zwUjltGfZLjDewD1Kcb+3gdgCiD+V8wQQ1xg8H15nql4WpK6P8s=
=bMvT
-----END PGP SIGNATURE-----
Merge tag 'regulator-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator updates from Mark Brown:
"The main thing this time around is support for suspend mode
configuration from DT which will enable some very useful power savings
on systems where we can't rely on the bootloader configuration. We
still don't really support dynamic configuration of this at runtime,
that may come later if there is any demand.
Summary:
- Support for specifying the target regulation mode and voltage
during system suspend via DT, enabling power savings in that mode.
- Reduce the default verbosity of the logging on boot, improving boot
times especially for systems with very large numbers of regulators.
- Lots of cleanups and fixes for Maxim PMIC drivers.
- New driver for Richtek RT5033"
* tag 'regulator-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (62 commits)
regulator: core: Fix regualtor_ena_gpio_free not to access pin after freeing
regulator: sky81452: Modify Device Tree structure
regulator: sky81452: Modify Device Tree structure
dt-bindings: Update documentation for "system-power-controller" and fix misspellings
of: Rename "poweroff-source" property to "system-power-controller"
regulator: max77686: Remove support for board files
regulator: max77802: Remove support for board files
regulator: max77802: Fill regulator modes translation callback
regulator: max77802: Document binding for regulator operating modes
regulator: of: Add support for parsing initial and suspend modes
regulator: of: Pass the regulator description in the match table
regulator: of: Add regulator desc param to of_get_regulator_init_data()
regulator: Add mode mapping function to struct regulator_desc
regulator: Document binding for initial and suspend modes
regulator: core: Add PRE_DISABLE notification
regulator: gpio: fix parsing of gpio list
regulator: rpm: add support for RPM-controller SMB208
regulator: da9063: Do not transform local IRQ to virtual
regulator: sky81452: Modify dependent Kconfig symbol
regulator: rt5033: Add RT5033 Regulator device driver
...
This patch adds S2MPS13 regulator device to existing S2MPS11 device driver.
The S2MPS13 has just different number of regulators from S2MPS14.
The S2MPS13 regulator device includes LDO[1-40] and BUCK[1-10].
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Sangbeom Kim <sbkim73@samsung.com>
Acked-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch add device driver of Richtek RT5033 PMIC.
The driver support multiple regulator like LDO and synchronous Buck.
The integrated synchronous buck converter is designed to provide 0.6 A
application with high efficiency. Two LDOs are integrated. One safe LDO is
for 60mA and the other one LDO is for 150 mA.
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Beomho Seo <beomho.seo@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rename st-pwm to pwm-regulator. And support getting voltage & duty table from
device tree, other platforms can also use this driver without any modify.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Tested-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Driver for regulators exposed by the Resource Power Manager (RPM) found
in Qualcomm 8660, 8960 and 8064 based devices.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix ERROR: "devm_regmap_init_i2c" [drivers/regulator/isl9305.ko] undefined!
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The ISL9305 and ISL9305H are mini-PMICs offering two DCDC regulators and
two LDO regulators. While there are some register differences between them
these do not affect the current Linux driver as the relevant features are
not yet supported.
Signed-off-by: Mark Brown <broonie@kernel.org>
This driver supports the 3 DCDC and 7 LDO regulators available on
Ricoh RN5T618 PMIC.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The regulator module consists of 4 DCDCs, 8 LDOs and 2 switches.
The output voltages are configurable and are meant to supply power
to the main processor and other components
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The MAX77802 PMIC has 10 high-efficiency Buck and 32 Low-dropout
(LDO) regulators. This patch adds support for all these regulators
found on the MAX77802 PMIC and is based on a driver added by Simon
Glass to the Chrome OS kernel 3.8 tree.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add driver support for HiSilicon Hi6421 voltage regulators.
Two rules for regulator enabling are defined in hi6421 spec:
1) Between disable and enable of each regulator (LDOs or BUCKs), there must
be a protection gap. Use @off_on_delay of regulator core to implement this.
2) No two regulators can be enabled at the same time. Use mutex in
hi6421_regulator_pdata to ensure this. A protection gap of 100us is added
into each LDO/BUCK's .enable_time.
Signed-off-by: Guodong Xu <guodong.xu@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
This driver also supports S2MPU02 now, thus update module description and
Kconfig accordingly.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This is the driver for the Dialog DA9211 Multi-phase 12A DC-DC Buck
Converter regulator. It communicates via an I2C bus to the device.
Signed-off-by: James Ban <james.ban.opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The bulk of the changes for this release are a few new drivers however
there are a couple of noticable core changes and the usual stream of
cleanups and fixes:
- Move disable of unused regulators later in init so it comes after
deferred probe has iterated making startup smoother.
- Fixes reference counting of the DT nodes for constraints from Charles
Keepax. This has little practical impact since all real users of
the regulator bindings use FDT which doesn't need the reference
counting.
- Lots of cleanups, especially to the Samsung drivers.
- Support for Linear Technologies LTC3589, Texas Instruments TPS658640
and X-Powers AXP20x.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=JrfM
-----END PGP SIGNATURE-----
Merge tag 'regulator-v3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator into next
Pull regulator updates from Mark Brown:
"The bulk of the changes for this release are a few new drivers however
there are a couple of noticable core changes and the usual stream of
cleanups and fixes:
- move disable of unused regulators later in init so it comes after
deferred probe has iterated making startup smoother.
- fixes to reference counting of the DT nodes for constraints from
Charles Keepax. This has little practical impact since all real
users of the regulator bindings use FDT which doesn't need the
reference counting.
- lots of cleanups, especially to the Samsung drivers.
- support for Linear Technologies LTC3589, Texas Instruments
TPS658640 and X-Powers AXP20x"
* tag 'regulator-v3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (64 commits)
regulator: pbias: remove unnecessary OOM messages
regulator: max8649: remove unnecessary OOM messages
regulator: core: Fix the init of DT defined fixed regulators
regulator: core: Disable unused regulators after deferred probing is done
regulator: Don't disable unused regulators we don't have permission for
regulator: axp20x: Use regulator_map_voltage_ascend for LDO4
regulator: use of_property_read_{bool|u32}()
regulator: Fix regulator_get_{optional,exclusive}() documentation
regulators: Add definition of regulator_set_voltage_time() for !CONFIG_REGULATOR
regulator: arizona-ldo1: add missing #include
regulator: pfuze100: Support enable/disable for fixed regulator
regulator: ltc3589: Remove ltc3589_list_voltage_fixed function
regulator: ltc3589: Fix module dependency
regulator: tps6586x: Remove unused to_tps6586x_dev() function
regulator: tps65218: Convert to use regulator_set_voltage_time_sel
regulator: tps6586x: Add support for the TPS658640
regulator: tps6586x: Prepare supporting fixed regulators
regulator: pfuze100: Don't allocate an invalid gpio
regulator: pfuze100: Support SWB enable/disable
regulator: fixed: use of_property_read_{bool|u32}()
...
Make this driver depend on I2C and select REGMAP_I2C to fix build failure.
Also allows this driver to be built as module.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds support for the Linear Technology LTC3589, LTC3589-1,
and LTC3589-2 8-output I2C voltage regulator ICs.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add support for MAX77836 chipset and its additional two LDO regulators.
These LDO regulators are controlled by the PMIC block with additional
regmap (different I2C slave address).
The MAX77836 charger and safeout regulators are almost identical to
MAX14577. The registers layout is the same, except values for charger's
current. The patch adds simple mapping between device type and supported
current by the charger regulator.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
AXP202 and AXP209 come with two synchronous step-down DC-DCs and five
LDOs. This patch introduces basic support for those regulators.
Signed-off-by: Carlo Caione <carlo@caione.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Core:
- CONFIG_MMC_UNSAFE_RESUME=y is now default behavior.
- DT bindings for SDHCI UHS, eMMC HS200, high-speed DDR, at 1.8/1.2V.
- Add GPIO descriptor based slot-gpio card detect API.
Drivers:
- dw_mmc: Refactor SOCFPGA support as a variant inside dw_mmc-pltfm.c.
- mmci: Support HW busy detection on ux500.
- omap: Support MMC_ERASE.
- omap_hsmmc: Support MMC_PM_KEEP_POWER, MMC_PM_WAKE_SDIO_IRQ, (a)cmd23.
- rtsx: Support pre-req/post-req async.
- sdhci: Add support for Realtek RTS5250 controllers.
- sdhci-acpi: Add support for 80860F16, fix 80860F14/SDIO card detect.
- sdhci-msm: Add new driver for Qualcomm SDHCI chipset support.
- sdhci-pxav3: Add support for Marvell Armada 380 and 385 SoCs.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=6S8w
-----END PGP SIGNATURE-----
Merge tag 'mmc-updates-for-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC updates from Chris Ball:
"MMC highlights for 3.15:
Core:
- CONFIG_MMC_UNSAFE_RESUME=y is now default behavior
- DT bindings for SDHCI UHS, eMMC HS200, high-speed DDR, at 1.8/1.2V
- Add GPIO descriptor based slot-gpio card detect API
Drivers:
- dw_mmc: Refactor SOCFPGA support as a variant inside dw_mmc-pltfm.c
- mmci: Support HW busy detection on ux500
- omap: Support MMC_ERASE
- omap_hsmmc: Support MMC_PM_KEEP_POWER, MMC_PM_WAKE_SDIO_IRQ, (a)cmd23
- rtsx: Support pre-req/post-req async
- sdhci: Add support for Realtek RTS5250 controllers
- sdhci-acpi: Add support for 80860F16, fix 80860F14/SDIO card detect
- sdhci-msm: Add new driver for Qualcomm SDHCI chipset support
- sdhci-pxav3: Add support for Marvell Armada 380 and 385 SoCs"
* tag 'mmc-updates-for-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (102 commits)
mmc: sdhci-acpi: Intel SDIO has broken card detect
mmc: sdhci-pxav3: add support for the Armada 38x SDHCI controller
mmc: sdhci-msm: Add platform_execute_tuning implementation
mmc: sdhci-msm: Initial support for Qualcomm chipsets
mmc: sdhci-msm: Qualcomm SDHCI binding documentation
sdhci: only reprogram retuning timer when flag is set
mmc: rename ARCH_BCM to ARCH_BCM_MOBILE
mmc: sdhci: Allow for irq being shared
mmc: sdhci-acpi: Add device id 80860F16
mmc: sdhci-acpi: Fix broken card detect for ACPI HID 80860F14
mmc: slot-gpio: Add GPIO descriptor based CD GPIO API
mmc: slot-gpio: Split out CD IRQ request into a separate function
mmc: slot-gpio: Record GPIO descriptors instead of GPIO numbers
Revert "dts: socfpga: Add support for SD/MMC on the SOCFPGA platform"
mmc: sdhci-spear: use generic card detection gpio support
mmc: sdhci-spear: remove support for power gpio
mmc: sdhci-spear: simplify resource handling
mmc: sdhci-spear: fix platform_data usage
mmc: sdhci-spear: fix error handling paths for DT
mmc: sdhci-bcm-kona: fix build errors when built-in
...
On some STMicroelectronics hardware reside regulators consisting
partly of a PWM input connected to the feedback loop. As the PWM
duty-cycle is varied the output voltage adapts. This driver
allows us to vary the output voltage by adapting the PWM input
duty-cycle.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add support for S2MPS14 PMIC regulators to s2mps11 driver. The S2MPS14
has fewer BUCK-s and LDO-s than S2MPS11. It also does not support
controlling the BUCK ramp delay.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Reviewed-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add support for S2MPA01 voltage and current regulator.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add a regulator driver for the BCM590xx PMU voltage regulators.
The driver supports LDOs and DCDCs in normal mode only. There is
no support for low-power mode or power sequencing.
Signed-off-by: Matt Porter <mporter@linaro.org>
Reviewed-by: Tim Kryger <tim.kryger@linaro.org>
Reviewed-by: Markus Mayer <markus.mayer@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
pbias register controls internal power supply to sd card i/o pads
in most OMAPs (OMAP2-5, DRA7).
Control bits for selecting voltage level and
enabling/disabling are in the same PBIAS register.
Signed-off-by: Balaji T K <balajitk@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Mark Brown <broonie@linaro.org>
Tested-by: Florian Vaussard <florian.vaussard@epfl.ch>
Tested-by: Stefan Roese <sr@denx.de>
Signed-off-by: Chris Ball <chris@printf.net>
This is a DT-only driver, so make it depend on OF and remove of_match_ptr in
the code.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds support for TPS65218 PMIC regulators.
The regulators set consists of 6 DCDCs and 1 LDO. The output
voltages are configurable and are meant to supply power to the
main processor and other components.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
A respin of the merges in the previous pull request with one extra fix.
A quiet release for the regulator API, quite a large number of small
improvements all over but other than the addition of new drivers for the
AS3722 and MAX14577 there is nothing of substantial non-local impact.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=1NsR
-----END PGP SIGNATURE-----
Merge tag 'regulator-v3.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator updates from Mark Brown:
"A respin of the merges in the previous pull request with one extra
fix.
A quiet release for the regulator API, quite a large number of small
improvements all over but other than the addition of new drivers for
the AS3722 and MAX14577 there is nothing of substantial non-local
impact"
* tag 'regulator-v3.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (47 commits)
regulator: pfuze100-regulator: Improve dev_info() message
regulator: pfuze100-regulator: Fix some checkpatch complaints
regulator: twl: Fix checkpatch issue
regulator: core: Fix checkpatch issue
regulator: anatop-regulator: Remove unneeded memset()
regulator: s5m8767: Update LDO index in s5m8767-regulator.txt
regulator: as3722: set enable time for SD0/1/6
regulator: as3722: detect SD0 low-voltage mode
regulator: tps62360: Fix up a pointer-integer size mismatch warning
regulator: anatop-regulator: Remove unneeded kstrdup()
regulator: act8865: Fix build error when !OF
regulator: act8865: register all regulators regardless of how many are used
regulator: wm831x-dcdc: Remove unneeded 'err' label
regulator: anatop-regulator: Add MODULE_ALIAS()
regulator: act8865: fix incorrect devm_kzalloc for act8865
regulator: act8865: Remove set_suspend_[en|dis]able implementation
regulator: act8865: Remove unneeded regulator_unregister() calls
regulator: s2mps11: Clean up redundant code
regulator: tps65910: Simplify setting enable_mask for regulators
regulator: act8865: add device tree binding doc
...
Symbol MFD_MC13783 always selected by MFD_MC13XXX, so no need
to keep additional symbol.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Make PFUZE100 entry consistent with other Freescale PMIC entries, so that now
we can have:
<*> Freescale MC13783 regulator driver
<*> Freescale MC13892 regulator driver
<*> Freescale PFUZE100 regulator driver
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Robin Gong <yibin.gong@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
MAX14577 chip is a multi-function device which includes MUIC,
charger and voltage regulator. The driver is located in drivers/mfd.
This patch adds regulator driver for MAX14577 chip. There are two
regulators in this chip:
1. Safeout LDO with constant voltage output of 4.9V. It can be only
enabled or disabled.
2. Current regulator for the charger. It provides current from 90mA up
to 950mA.
Driver supports Device Tree.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The AMS AS3722 is a compact system PMU suitable for mobile phones,
tablets etc. It has 4 DCDC step down regulators, 3 DCDC step down
controller, 11 LDOs.
Add a driver to support accessing the DCDC/LDOs found on the AMS
AS3722 PMIC using regulators.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Florian Lobmaier <florian.lobmaier@ams.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The ST Microelectronics STw481x PMIC used for the Nomadik
has one single software-controlled regulator for VMMC.
This driver registers directly to the compatible string
as there is just one regulator.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
When a system has said that it has fully specified constraints for its
regulators it is still possible that some supplies may be missing,
especially if regulator support has been added to a driver after the
board was integrated. We can handle such situations more gracefully by
providing a dummy regulator.
Unless the caller has specifically indicated that the system design may
not include a given regulator by using regulator_get_optional() or that
it needs its interactions to have an effect using regulator_get_exclusive()
provide a dummy regulator if we can't locate a real one.
The kconfig option REGULATOR_DUMMY that provided similar behaviour for all
regulators has been removed, systems that need it should flag that they
have full constraints instead.
Signed-off-by: Mark Brown <broonie@linaro.org>
lp872x regulator driver can be built a module after commit 631a1fc
"regulator: build: Allow most regulators to be built as modules".
Make REGULATOR_LP872X depend on I2C to allow building lp872x module when I2C=m.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The driver adds support for the following DA9063 PMIC regulators:
- 11x LDOs (named LDO1 - LDO11),
- 6x buck converters (BCORE1, BCORE2, BPRO, BMEM, BIO, BPERI),
Regulators provide following operations:
- REGULATOR_CHANGE_STATUS and REGULATOR_CHANGE_VOLTAGE for all regulators,
- REGULATOR_CHANGE_MODE for LDOs and buck converters, where:
- LDOs allow REGULATOR_MODE_NORMAL and REGULATOR_MODE_STANDBY,
- buck converters allow REGULATOR_MODE_FAST, REGULATOR_MODE_NORMAL
and REGULATOR_MODE_STANDBY,
- REGULATOR_CHANGE_CURRENT for buck converters (current limits).
The driver generates REGULATOR_EVENT_OVER_CURRENT for LDO3, LDO4, LDO7, LDO8
and LDO11.
Internally, PMIC provides two voltage configurations for normal and suspend
system state for each regulator. The driver switches between those on
suspend/wake-up to provide quick and fluent output voltage change.
This driver requires MFD core driver for operation.
Signed-off-by: Krystian Garbaciak <krystian.garbaciak@diasemi.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
I2C driver for the Dialog DA9210 Multi-phase 12A DC-DC Buck.
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: David Dajun Chen <david.chen@diasemi.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This fixes below build errors:
CC [M] drivers/regulator/pfuze100-regulator.o
drivers/regulator/pfuze100-regulator.c:342:21: error: variable 'pfuze_regmap_config' has initializer but incomplete type
drivers/regulator/pfuze100-regulator.c:343:2: error: unknown field 'reg_bits' specified in initializer
drivers/regulator/pfuze100-regulator.c:343:2: warning: excess elements in struct initializer [enabled by default]
drivers/regulator/pfuze100-regulator.c:343:2: warning: (near initialization for 'pfuze_regmap_config') [enabled by default]
drivers/regulator/pfuze100-regulator.c:344:2: error: unknown field 'val_bits' specified in initializer
drivers/regulator/pfuze100-regulator.c:344:2: warning: excess elements in struct initializer [enabled by default]
drivers/regulator/pfuze100-regulator.c:344:2: warning: (near initialization for 'pfuze_regmap_config') [enabled by default]
drivers/regulator/pfuze100-regulator.c:345:2: error: unknown field 'max_register' specified in initializer
drivers/regulator/pfuze100-regulator.c:345:2: warning: excess elements in struct initializer [enabled by default]
drivers/regulator/pfuze100-regulator.c:345:2: warning: (near initialization for 'pfuze_regmap_config') [enabled by default]
drivers/regulator/pfuze100-regulator.c:346:2: error: unknown field 'cache_type' specified in initializer
drivers/regulator/pfuze100-regulator.c:346:2: warning: excess elements in struct initializer [enabled by default]
drivers/regulator/pfuze100-regulator.c:346:2: warning: (near initialization for 'pfuze_regmap_config') [enabled by default]
drivers/regulator/pfuze100-regulator.c: In function 'pfuze100_regulator_probe':
drivers/regulator/pfuze100-regulator.c:370:2: error: implicit declaration of function 'devm_regmap_init_i2c' [-Werror=implicit-function-declaration]
drivers/regulator/pfuze100-regulator.c:370:21: warning: assignment makes pointer from integer without a cast [enabled by default]
cc1: some warnings being treated as errors
make[2]: *** [drivers/regulator/pfuze100-regulator.o] Error 1
make[1]: *** [drivers/regulator] Error 2
make: *** [drivers] Error 2
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add pfuze100 regulator driver.
Signed-off-by: Robin Gong <b38343@freescale.com>
Tested-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
This driver can be built as a module, make it depend on MFD_88PM800.
Otherwise, we are not able to select this driver when MFD_88PM800=m.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add the regulator driver for PMIC 88pm800 including device tree
support.
88pm800 is an I2C-based power-management IC containing voltage
regulators, a real-time clock, and some general purpose ADC devices,
Signed-off-by: Yi Zhang <yizhang@marvell.com>
Signed-off-by: Chao Xie <chao.xie@marvell.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds new regulator driver to support max77693 chip's regulators.
max77693 has two linear voltage regulators and one current regulator which
can be controlled through I2C bus. This driver also supports device tree.
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Adaptive Body Biasing (ABB) modulates transistor bias voltages
dynamically in order to optimize switching speed versus leakage.
Texas Instruments' SmartReflex 2 technology provides support for this
power management technique with Forward Body Biasing (FBB) and Reverse
Body Biasing (RBB). These modulate the body voltage of transistor
cells or blocks dynamically to gain performance and reduce leakage.
TI's SmartReflex white paper[1] has further information for usage in
conjunction with other power management techniques.
The application of FBB/RBB technique is determined for each unique
device in some process nodes, whereas, they are mandated on other
process nodes.
In a nutshell, ABB technique is implemented on TI SoC as an on-chip
LDO which has ABB module controlling the bias voltage. However, the
voltage is unique per device. These vary per SoC family and the manner
in which these techniques are used may vary depending on the Operating
Performance Point (OPP) voltage targeted. For example:
OMAP3630/OMAP4430: certain OPPs mandate usage of FBB independent of
devices.
OMAP4460/OMAP4470: certain OPPs mandate usage of FBB, while others may
optionally use FBB or optimization with RBB.
OMAP5: ALL OPPs may optionally use ABB, and ABB biasing voltage is
influenced by vset fused in s/w and requiring s/w override of
default values.
Further, two generations of ABB module are used in various TI SoCs.
They have remained mostly register field compatible, however the
register offset had switched between versions.
We introduce ABB LDO support in the form of a regulator which is
controlled by voltages denoting the desired Operating Performance
Point which is targeted. However, since ABB transition is part of OPP
change sequence, the sequencing required to ensure sane operation
w.r.t OPP change is left to the controlling driver (example: cpufreq
SoC driver) using standard regulator operations.
The driver supports all ABB modes and ability to override ABB LDO vset
control efuse based ABB mode detection etc.
Current implementation is heavily influenced by the original patch
series [2][3] from Mike Turquette. However, the current implementation
supports only device tree based information.
[1] http://www.ti.com/pdfs/wtbu/smartreflex_whitepaper.pdf
[2] http://marc.info/?l=linux-omap&m=134931341818379&w=2
[3] http://marc.info/?l=linux-arm-kernel&m=134931402406853&w=2
[nm@ti.com: co-developer]
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Andrii.Tseglytskyi <andrii.tseglytskyi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
GENERIC_GPIO is now equivalent to GPIOLIB and features that depended on
GENERIC_GPIO can now depend on GPIOLIB to allow removal of this option.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
If we are in non-bypass mode then the SYSCLK is required for full charge
pump operation, otherwise we will fall back to bypass mode. Use the DAPM
context exposed by the ASoC driver to manage this.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch is for new lp8755 regulator dirver and
several unsed variables were deleted and then test was done.
LP8755 :
The LP8755 is a high performance power management unit.It contains
six step-down DC-DC converters which can can be filexibly bundled
together in multiphase converters as required by application.
www.ti.com
Signed-off-by: Daniel Jeong <gshark.jeong@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This driver supports the 4 DCDC and 8 LDO regulators on the AS3711 PMIC.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The MAXIM MAX8973 high-efficiency, three phase, DC-DC step-down
switching regulator delievers up to 9A of output current. Each
phase operates at a 2MHz fixed frequency with a 120 deg shift
from the adjacent phase, allowing the use of small magnetic
component.
Add regulator driver for this device.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is the Regulator patch for the DA9055 PMIC and has got dependency on
the DA9055 MFD core.
This patch support all of the DA9055 regulators. The output voltages are
fully programmable through I2C interface only. The platform data with regulation
constraints is passed down from the board to the regulator.
This patch is functionaly tested on SMDK6410 board. DA9055 Evaluation board
was connected to the SMDK6410 board.
Signed-off-by: David Dajun Chen <dchen@diasemi.com>
Signed-off-by: Ashish Jangam <ashish.jangam@kpitcummins.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add regulator driver for Texas Instrument TPS80031/TPS80032 device.
TPS80031/ TPS80032 Fully Integrated Power Management with Power
Path and Battery Charger. It has 5 configurable step-down
converters, 11 general purpose LDOs, VBUS generator and digital
output to control regulators.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Implementation of the regulator framework driver for the
Versatile Express voltage control. Devices without
voltage constraints (ie. "regulator-[min|max]-microvolt"
properties in the DT node) are treated as fixed (or rather
read-only) regulators.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The TPS51632 is a driverless step down controller with
serial control. Advanced features such as D-Cap+
architecture with overlapping pulse support and OSR
overshoot reduction provide fast transient response,
lowest output capacitance and high efficiency.
The TPS51632 supports both I2C and DVFS interfaces
(through PWM) for dynamic control of the output voltage
and current monitor telemetry.
Add regulator driver for TPS51632.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
As usual we have a few new drivers:
- TI LP8788
- TI OMAP USB TLL
- Maxim MAX8907
- SMSC ECE1099
- Dialog Semiconductor DA9055
- A simpler syscon driver that allow us to get rid of the anatop one.
Drivers are also gradually getting Device Tree and IRQ domain support.
The following drivers got DT support:
- palmas, 88pm860x, tc3589x and twl4030-audio
And those ones now use the IRQ domain APIs:
- 88pm860x, tc3589x, db8500_prcmu
Also some other interesting changes:
- Intel's ICH LPC now supports Lynx Point
- TI's twl4030-audio added a GPO child
- tps6527 enabled its backlight subdevice
- The twl6030 pwm driver moved to the new PWM subsystem
And finally a bunch of cleanup and casual fixes for mc13xxx, 88pm860x, palmas,
ab8500, wm8994, wm5110, max8907 and the tps65xxx family.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=n6lp
-----END PGP SIGNATURE-----
Merge tag 'mfd-3.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
Pull MFD changes from Samuel Ortiz:
"MFD bits for the 3.7 merge window.
As usual we have a few new drivers:
- TI LP8788
- TI OMAP USB TLL
- Maxim MAX8907
- SMSC ECE1099
- Dialog Semiconductor DA9055
- A simpler syscon driver that allow us to get rid of the anatop one.
Drivers are also gradually getting Device Tree and IRQ domain support.
The following drivers got DT support:
- palmas, 88pm860x, tc3589x and twl4030-audio
And those ones now use the IRQ domain APIs:
- 88pm860x, tc3589x, db8500_prcmu
Also some other interesting changes:
- Intel's ICH LPC now supports Lynx Point
- TI's twl4030-audio added a GPO child
- tps6527 enabled its backlight subdevice
- The twl6030 pwm driver moved to the new PWM subsystem
And finally a bunch of cleanup and casual fixes for mc13xxx, 88pm860x,
palmas, ab8500, wm8994, wm5110, max8907 and the tps65xxx family."
Fix up various annoying conflicts: the DT and IRQ domain support came in
twice and was already in 3.6. And then it was apparently rebased.
Guys, DON'T REBASE!
* tag 'mfd-3.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (89 commits)
ARM: dts: Enable 88pm860x pmic
mfd: 88pm860x: Move gpadc init into touch
mfd: 88pm860x: Device tree support
mfd: 88pm860x: Use irqdomain
mfd: smsc: Add support for smsc gpio io/keypad driver
backlight: tps65217_bl: Add missing platform_set_drvdata in tps65217_bl_probe
mfd: DA9055 core driver
mfd: tps65910: Add alarm interrupt of TPS65910 RTC to mfd device list
mfd: wm5110: Add register patches for revision B
mfd: wm5110: Disable control interface error report for WM5110 rev B
mfd: max8907: Remove regulator-compatible from DT docs
backlight: Add TPS65217 WLED driver
mfd: Add backlight as subdevice to the tps65217
mfd: Provide the PRCMU with its own IRQ domain
mfd: Fix max8907 sparse warning
mfd: Add lp8788 mfd driver
mfd: dbx500: Provide a more accurate smp_twd clock
mfd: rc5t583: Fix warning messages
regulator: palmas: Add DT support
mfd: palmas: Change regulator defns to better suite DT
...
Using syscon to access anatop register.
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This driver supports Fairchild FAN53555 Digitally Programmable
TinyBuck Regulator. The FAN53555 is a step-down switching voltage
regulator that delivers a digitally programmable output from an
input voltage supply of 2.5V to 5.5V. The output voltage is
programmed through an I2C interface.
Signed-off-by: Yunfan Zhang <yfzhang@marvell.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The MAX8907 is an I2C-based power-management IC containing voltage
regulators, a reset controller, a real-time clock, and a touch-screen
controller.
The original driver was written by:
* Gyungoh Yoo <jack.yoo@maxim-ic.com>
Various fixes and enhancements by:
* Jin Park <jinyoungp@nvidia.com>
* Tom Cherry <tcherry@nvidia.com>
* Prashant Gaikwad <pgaikwad@nvidia.com>
* Dan Willemsen <dwillemsen@nvidia.com>
* Laxman Dewangan <ldewangan@nvidia.com>
During upstreaming, I (swarren):
* Converted to regmap.
* Allowed probing from device tree.
* Reworked the regulator driver to be represented as a single device that
provides multiple regulators, rather than as a device per regulator.
* Replaced many regulator ops with standard functions.
* Added ability to specify supplies for each regulator.
* Removed the WLED regulator. If/when we expose this in the driver, it
should be a backlight object not a regulator object.
* Renamed from max8907c->max8907, since the driver covers at least the
C and B revisions.
* General cleanup.
Signed-off-by: Gyungoh Yoo <jack.yoo@maxim-ic.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Too many thens in the if...then clause.
Reported-by: Michael Jones <michael.jones@matrix-vision.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We have support for a few new drivers:
- Samsung s2mps11
- Wolfson Microelectronics wm5102 and wm5110
- Marvell 88PM800 and 88PM805
- TI twl6041
We also have our regular driver improvements:
- Device tree and IRQ domain support for STE AB8500
- Regmap and devm_* API conversion for TI tps6586x
- Device tree support for Samsung max77686
- devm_* API conversion for STE AB3100
Besides that, quite a lot of fixing and cleanup for mc13xxx, tps65910,
tps65090, da9052 and twl-core.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIcBAABAgAGBQJQFpGVAAoJEIqAPN1PVmxKFNoP/1dkYngrxxV6cxdyLJ74APhG
lVKPgaDxQhdgfwCZJmMeZK1UphZo80cWnEXG6sTHZUEQdTaslSJu5SuPfUM+fo7e
52/dU0nx0ZE04pwPQLHbidS4TmHlbLg9oM2kmIf9RO5rg34GodwVgRL/4+k1qvhz
aWYJt9erFhQOpqaSX66mXHSuhvzHypbcE7d2B2Ykmh3NoYiH2w9H9KmIbbb+ZLq8
+Bp/i5Ys/vfooo+8IE2w6KZfIzMwsmmtWjjr/38yuQJaKZCh/zn23DM9HsdrVf++
RzfniRF4YBxmeKi7zi8MFIYys8filTCXA9dXbGSAKCuUCT37yZRnUxTeN1bn7Bux
A7KRpG7pUKQKVKqCTndvK5LcQKlT33XyW2ZzV1wVWX2JkCJ+gilPeykb8IabNvGX
nIp0STEGR/WdCLEAKo8pJF7Usn0RuUzAug02SG/mQ6dpnLoZqp0Od5W7gRhT7M7h
hXr/xKJ6cG5YwicpAdy5kJJ0dRgQrtaHwxrF0B68AXZ7CmAtkPuEGCYhUCFnGQUH
XJ0CodAqqVBRyYiQS4zIpIh2nqhIdsgv4OC1+kVLbubQk+PR88zG9Jvg6i1HQi/A
OHi7N5Wite3YUrs3sBzDKnEc/Il2YRhVaz2SLVNfZR0PS7hywHN3rK/tVFINTgei
jNEz1H6hu7ToNLfs0UzP
=c28c
-----END PGP SIGNATURE-----
Merge tag 'mfd-3.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
Pull MFD bits from Samuel Ortiz:
"We have support for a few new drivers:
- Samsung s2mps11
- Wolfson Microelectronics wm5102 and wm5110
- Marvell 88PM800 and 88PM805
- TI twl6041
We also have our regular driver improvements:
- Device tree and IRQ domain support for STE AB8500
- Regmap and devm_* API conversion for TI tps6586x
- Device tree support for Samsung max77686
- devm_* API conversion for STE AB3100
Besides that, quite a lot of fixing and cleanup for mc13xxx, tps65910,
tps65090, da9052 and twl-core."
Fix up mostly trivial conflicts, with the exception of
drivers/usb/host/ehci-omap.c in particular, which had some
re-organization of the reset sequence (commit 1a49e2ac9651: "EHCI:
centralize controller initialization") that clashed with commit
2761a63945 ("mfd: USB: Fix the omap-usb EHCI ULPI PHY reset fix
issues").
In particular, commit 2761a63945 moved the usb_add_hcd() to the
*middle* of the reset sequence, which clashes fairly badly with the
reset sequence re-organization (although it could have been done inside
the new omap_ehci_init() function).
I left that part of commit 2761a63945 just undone.
* tag 'mfd-3.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (110 commits)
mfd: Ensure AB8500 platform data is passed through db8500-prcmu to MFD Core
mfd: Arizone core should select MFD_CORE
mfd: Fix arizona-irq.c build by selecting REGMAP_IRQ
mfd: Add debug trace on entering and leaving arizone runtime suspend
mfd: Correct tps65090 cell names
mfd: Remove gpio support from tps6586x core driver
ARM: tegra: defconfig: Enable tps6586x gpio
gpio: tps6586x: Add gpio support through platform driver
mfd: Cache tps6586x register through regmap
mfd: Use regmap for tps6586x register access.
mfd: Use devm managed resources for tps6586x
input: Add onkey support for 88PM80X PMIC
mfd: Add support for twl6041
mfd: Fix twl6040 revision information
mfd: Matches should be NULL when populate anatop child devices
input: ab8500-ponkey: Create AB8500 domain IRQ mapping
mfd: Add missing out of memory check for pcf50633
Documentation: Describe the AB8500 Device Tree bindings
mfd: Add tps65910 32-kHz-crystal-input init
mfd: Drop modifying mc13xxx driver's id_table in probe
...
TI LP8788 PMU has 4 BUCKS and 22 LDOs.
The voltage of BUCK1 and BUCK2 can be controlled by external gpios.
And some LDOs also can be enabled by external gpios.
The regmap interface is used for regulator operations.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Previously, Samsung PMIC naming rule start with prefix of s5m.
But Naming rule is changed.
From now on, Prefix will be changed to s2m.
So, To support pmic series of s5m and s2m, change mfd file and directory name.
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch add Samsung S2MPS11 regulator driver.
The S2MPS11 can support 10 Bucks and 38 LDOs and RTC.
Especially, S2MPS11 is designed for high performance
Samsung application processor.
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Kconfig doesn't do the right thing for us here.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The Wolfson Arizona platform is used for a range of low power audio hub
CODECs. Many of these devices feature an integrated power supply for the
microphone which is supported by this driver.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fixes link failure due to devm_gpio_request_one()
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This driver supports TI/National LP8720, LP8725 PMIC.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Reviewed-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add driver for support max77686 regulator.
MAX77686 provides LDOs[1~26] and BUCKs[1~9]. It support to set or get the
volatege of regulator on max77686 chip with using regmap.
Signed-off-by: Chiwoong Byun <woong.byun@samsung.com>
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add the Kconfig/Makefile stuff for the palmas regulator driver
Signed-off-by: Graeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The RC5T583 PMIC from RICOH consists of 4 DCDC and 10
LDOs. This driver supports the control of different
regulator output through regulator interface.
This driver depends on MFD driver of RC5T583 and uses
mfd rc5t583 apis to communicate to device for accessing
different device's registers.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
According to the datasheet[1], tps62360 is register compatible with tps62362.
tps62361B is register compatible with tps62363.
Thus this patch adds support for tps62362 and tps62363.
[1] http://www.ti.com/litv/pdf/slvsau9b
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add TPS65090 regulator driver
TPS65090 PMIC from TI consists of 3 step down converters,
2 always on LDOs and 7 current limited load switches. The
output voltages are ON/OFF controllable and are meant to
supply power to the components on target board.
Signed-off-by: Venu Byravarasu <vbyravarasu@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The pxa regulator branch removes the bq24022 driver, while a lot of
other regulator drivers got added in the regulator tree. This
resolves the trivial conflicts by merging in the regulator patches
that are already merged into v3.4.
Conflicts:
drivers/regulator/Kconfig
drivers/regulator/Makefile
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Anatop is an integrated regulator inside i.MX6 SoC.
There are 3 digital regulators which controls PU, CORE (ARM), and SOC.
And 3 analog regulators which controls 1P1, 2P5, 3P0 (USB).
This patch adds the Anatop regulator driver.
Signed-off-by: Nancy Chen <Nancy.Chen@freescale.com>
Signed-off-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Sort Kconfig entries by company name/driver in alphabetical order.
Sort Makefile entries by alphabetical order.
In order to group all the Kconfig entries by company name,
this patch also adds company name to some Kconfig entries.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix the module desciption and also update Kconfig to include supporting
tps65911 chip.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The bq24022 driver is just a specialised form of a gpio-regulator.
As all former users of it now use the gpio-regulator directly, there
is no need to keep it around.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
This patch adds tps65217 PMIC as a regulator
The regulator module consists of 3 DCDCs and 4 LDOs. The output
voltages are configurable and are meant to supply power to the
main processor and other components
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch add Samsung S5M8767A pmic configuration.
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
As we progress with DB5500 and future voltage domain regulators
based on very similar hardware as found in the DB8500 PRCMU,
it makes sense to split off the generic parts and introduce
some generic debug code for the DBx500 regulators. This patch
accoplish a basic abstraction of the DBx500 voltage domain
regulators.
Signed-off-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The regulator module consists of 1 DCDC. The output voltage
is configurable and is meant for supply power to the core
voltage of Soc.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The Dialog PMIC has below featured regulators:-
DA9052-BC - 4 DVS Buck converters 0.5V - 3.6V upto 1Amp.
DA9053-AA/BX - 4 DVS Buck converters 0.5V - 2.5V upto 3Amp.
DA9052/53 - 10 Programmable LDO's High PSSR, 1% accuracy.
This patch support all the DA9052 and Da9053 regulators. The output voltages are
fully programmable via I2C or SPI interface. The platform data with regulation
constraints is passed down from the board to the regulator.
Signed-off-by: David Dajun Chen <dchen@diasemi.com>
Signed-off-by: Ashish Jangam <ashish.jangam@kpitcummins.com>
Tested-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Without GENERIC_GPIO "struct gpio" is undefined leading to errors.
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds support for regulators that can be controlled via gpios.
Examples for such regulators are the TI-tps65024x voltage regulators
with 4 fixed and 1 runtime-switchable voltage regulators
or the TI-bq240XX charger regulators.
The number of controlling gpios is not limited, the mapping between
voltage/current and target gpio state is done via the states map
and the driver can be used for either voltage or current regulators.
A mapping for a regulator with two GPIOs could look like:
gpios = {
{ .gpio = GPIO1, .flags = GPIOF_OUT_INIT_HIGH, .label = "gpio name 1" },
{ .gpio = GPIO2, .flags = GPIOF_OUT_INIT_LOW, .label = "gpio name 2" },
}
The flags element of the gpios array determines the initial state of
the gpio, set during probe. The initial state of the regulator is also
calculated from these values
states = {
{ .value = volt_or_cur1, .gpios = (0 << 1) | (0 << 0) },
{ .value = volt_or_cur2, .gpios = (0 << 1) | (1 << 0) },
{ .value = volt_or_cur3, .gpios = (1 << 1) | (0 << 0) },
{ .value = volt_or_cur4, .gpios = (1 << 1) | (1 << 0) },
}
The target-state for the n-th gpio is determined by the n-th bit
in the bitfield of the target-value.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add regulator driver for AnalogicTech AAT2870.
Signed-off-by: Jin Park <jinyoungp@nvidia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The tps65912 consist of 4 DCDCs and 10 LDOs. The output voltages can be
configured by the SPI or I2C interface, they are meant to supply power
to the main processor and other components.
Signed-off-by: Margarita Olaya Cabrera <magi@slimlogic.co.uk>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
The regulator module consists of 3 DCDCs and 8 LDOs. The output
voltages are configurable and are meant to supply power to the
main processor and other components
Signed-off-by: Graeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: Jorge Eduardo Candelaria <jedu@slimlogic.co.uk>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The DB8500 has ePOD:s (electronic power domains) which are possible
to switch on/off to deactivate silicon blocks on the DB8500 SoC
by cutting their power without retention. We model these as simple
regulators with one bit on/off settings.
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Signed-off-by: Sundar Iyer <sundar.iyer@stericsson.com>
Signed-off-by: Jonas Aberg <jonas.aberg@stericsson.com>
Signed-off-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Signed-off-by: Martin Persson <martin.persson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix typo: s/TPS695x0/TPS659x0/
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This adds a subdriver for the regulator found inside the TPS61050
and TPS61052 chips.
Cc: Samuel Ortiz <samuel.ortiz@intel.com>
Cc: Ola Lilja <ola.o.lilja@stericsson.com>
Cc: Jonas Aberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch supports PMIC/Regulator part of MAX8997/MAX8966 MFD.
In this initial release, selecting voltages or current-limit
and switching on/off the regulators are supported.
Controlling voltages for DVS with GPIOs is not implemented fully
and requires more considerations: it controls multiple bucks (selection
of 1, 2, and 5) at the same time with SET1~3 gpios. Thus, when DVS-GPIO
is activated, we lose the ability to control the voltage of a single
buck regulator independently; i.e., contolling a buck affects other two
bucks. Therefore, using the conventional regulator framework directly
might be problematic. However, in this driver, we try to choose
a setting without such side effect of affecting other regulators and
then try to choose a setting with the minimum side effect (the sum of
voltage changes in other regulators).
On the other hand, controlling all the three bucks simultenously based
on the voltage set table may help build cpufreq and similar system
more robust; i.e., all the three voltages are consistent every time
without glitches during transition.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Since the MFD core for this device and the regulator drivers for these
devices can be built modular we should also support modular build of
the shared code for the regulator drivers, otherwise we try to link
built in code against modular code with unfortunate results.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
move some common functions and micros of mc13783 regulaor driver to
a seperate file, which makes it possible for mc13892 to share code.
Signed-off-by: Yong Shen <yong.shen@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
TPS6524X provides three step-down converters and two general-purpose LDO
voltage regulators. This device is interfaced using SPI.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This patch adds regulator drivers for National Semiconductors LP3972 PMIC.
This LP3972 PMIC controller has 3 DC/DC voltage converters and 5 low drop-out
(LDO) regulators. LP3972 PMIC controller uses I2C interface.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
MAX8952 PMIC is used to provide voltage output between 770mV - 1400mV
with DVS support. In this initial release, users can set voltages for
four DVS modes, RAMP delay values, and SYNC frequency.
Controlling FPWM/SYNC_MODE/Pull-Down/Ramp Modes and reading CHIP_ID
is not supported in this release.
If GPIO of EN is not valid in platform data, the driver assumes that it
is always-on. If GPIO of VID0 or VID1 is invalid, the driver pulls down
VID0 and VID1 to fix DVS mode as 0 and disables DVS support.
We assume that V_OUT is capable to provide every voltage from 770mV to
1.40V in 10mV steps although the data sheet has some ambiguity on it.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
--
v2:
- Style correction
- Can accept platform_data with invalid GPIOs
- Removed unnecessary features
- Improved error handling
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Hi Mark,
> I think that's everything.
Please find the updated patch set as below.
>From f4bf7eec4d210db5075c0bce4521d9be6bc76c8c Mon Sep 17 00:00:00 2001
From: Sundar R Iyer <sundar.iyer@stericsson.com>
Date: Sun, 6 Jun 2010 19:12:12 +0530
Subject: [PATCH v3 1/2] regulator: add support for regulators on the ab8500 MFD
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Bengt JONSSON <bengt.g.jonsson@stericsson.com>
Signed-off-by: Sundar R Iyer <sundar.iyer@stericsson.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The MAX8998-pmic driver requires a core driver for all io operations. Like
other regulator driver make it depend of the required MFD io driver.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds voltage regulator driver for Maxim 8998 chip. This chip
is used on Samsung Aquila and GONI boards and provides following
functionalities:
- 4 BUCK voltage converters, 17 LDO power regulators and 5 other power
controllers
- battery charger
This patch adds basic driver for voltage regulators and MAX 8998 MFD core.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This device is very simple, it supports one buck and two LDOs. The LDOs are
fixed-voltage. Only the buck is programable over the I2C bus to 16 possible
voltages.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The AD5398 and AD5821 are single 10-bit DAC with 120 mA output current
sink capability. They feature an internal reference and operates from
a single 2.7 V to 5.5 V supply.
This driver supports both the AD5398 and the AD5821. It adapts into the
voltage and current framework.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
MAX8925 contains 3 Buck and 20 LDO regulator.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Rename 88PM8607 to 88PM860X in both Makefile and Kconfig under mfd directory.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In order to ease transitions with drivers are boards start using regulators
provide an option to cause all regulator_get() calls to succeed, with a
dummy always on regulator being supplied where one has not been configured.
A warning is printed whenever the dummy regulator is used to aid system
development.
This regulator does not implement any regulator operations but will allow
simple consumers which only do enable() and disable() calls to run. It
is kept separate from the fixed voltage regulator to avoid Kconfig
confusion on the part of users when it is extended to allow boards to
explicitly use the dummy regulator to simplify cases where the majority
of supplies are from fixed regulators without software control.
This option is currently only effective for systems which do not specify
full constriants. If required an override could also be provided to allow
these systems to use the dummy regulator, though it is likely that
unconfigured supplies on such systems will lead to error due to
regulators being powered down more aggressively when not in use.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The WM8994 contains two LDOs with mixed hardware/software control to
minimise the number of external supplies required while delivering
optimal voltages to minimise power consumption.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Fix Kconfig text for some Wolfson Micro devices.
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Mark Brown