Channel information which is read from EEPROM should
be read into an array containing per-channel information.
This removes the requirement of multiple arrays and makes
the channel handling a bit cleaner and easier to expand.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt73usb supports hardware encryption.
rt73usb supports up to 4 shared keys and up to 64 pairwise keys.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt61pci supports hardware encryption.
rt61pci supports up to 4 shared keys and up to 64 pairwise keys.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Various rt2x00 devices support hardware encryption.
Most of them require the IV/EIV to be generated by mac80211,
but require it to be provided seperately instead of within
the frame itself. This means that rt2x00lib should extract
the data from the frame and place it in the frame descriptor.
During RX the IV/EIV is provided in the descriptor by the
hardware which means that it should be inserted into the
frame by rt2x00lib.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The libertas thin firmware only supports usb devices, but the usb functions have
been kept separate to ease future support for other devices.
Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch contains most of the libertastf driver, just lacking command helper
functions and usb specific functions. Currently, monitor, managed, ap and mesh
interfaces are supported. Even though this driver supports the same hardware as
the "libertas" driver, it uses a different (thin) firmware, that makes it
suitable for a mac80211 driver.
Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ieee80211_get_hdrlen_from_skb internally checks that the skb is long
enough to hold the full header, or it returns 0 if not. The check in
ath5k does not check this case and assumes it always got the actual
header length which it then checks against the skb->len plus some headroom.
Change to ieee80211_hdrlen which always returns the hdrlen and keep the
existing headroom check.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Acked-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds another level for debugging host command. This adds an
option to suppress the debug prints for sensitivity and link quality
commands.
Signed-off-by: Esti Kummer <ester.kummer@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes struct iwl4965_lq_mngr it is not used.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
num_tbs is unsigned so the test doesn't work.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
remove drivers own implementation of radiotap in favor of the generic one
provided by mac80211.
also remove priv->add_radiotap because it is not used any more.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
cleanup the rates structures used by ath5k. instead of separate driver and
mac80211 rate structures we now setup a static ieee80211_rate array and use it
directly. no conversion between two different rate structures has to be done
any more. a lot of unused and confusing junk was deleted.
renamed ath5k_getchannels into ath5k_setup_bands because this is what it does.
rewrote it to copy the bitrates correctly for each band. this is necessary for
running different hardware with the same driver (e.g. 5211 and 5212 based
cards).
add special handling of rates for AR5211 chipsets: it uses different rate codes
for CCK rates (which are actually like the other chips but with a 0xF mask).
setup a hardware code to rate index reverse mapping table for getting the rate
index of received frames.
the rates for control frames which have to be set in
ath5k_hw_write_rate_duration are now in one single array.
drivers/net/wireless/ath5k/ath5k.h: Changes-licensed-under: ISC
drivers/net/wireless/ath5k/base.c: Changes-licensed-under: 3-Clause-BSD
drivers/net/wireless/ath5k/base.h: Changes-licensed-under: 3-Clause-BSD
drivers/net/wireless/ath5k/hw.c: Changes-licensed-under: ISC
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There were 3 code copy and pastes of reset. Unify the resets and place
in separate function.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Nick Kossifidis <mickflemm@gmail.com>
Cc: Luis R. Rodriguez <mcgrof@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is not allowed to use NETDEV_TX_BUSY in tx path anymore.
Signed-off-by: Daniel Wagner <wagi@monom.org>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This enables draft-802.11s Mesh Point operation. For that we need mesh
beaconing. Tested with AR5212/AR5213 PCI card against Zydas and b43 mesh
nodes.
Signed-off-by: Andrey Yurovsky <andrey@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To use these features, copy the boot2 and firmware images to /lib/firmware and:
echo <boot2_image_name> > /sys/class/net/ethX/lbs_flash_boot2
echo <firmware_image_name> > /sys/class/net/ethX/lbs_flash_fw
Signed-off-by: Brian Cavagnolo <brian@cozybit.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add locking and non-locking versions of if_usb_prog_firmware to support
programming firmware after and before driver bring-up respectively. Add more
suitable error codes for firmware programming process. Add capability checks
for persistent features before attempting to use them.
Based on patches from Brajesh Dave and Priyank Singh.
Signed-off-by: Brian Cavagnolo <brian@cozybit.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tx/Rx descriptor flags are common between rtl818x devices, only with
additions for newer chips, thus use same flags in the code.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The drivers below do not use LINUX_VERSION_CODE nor KERNEL_VERSION.
drivers/net/wireless/ath5k/base.c
drivers/net/wireless/b43/main.c
drivers/net/wireless/ipw2100.c
drivers/net/wireless/ipw2200.c
drivers/net/wireless/iwlwifi/iwl-3945.c
drivers/net/wireless/iwlwifi/iwl-4965.c
drivers/net/wireless/iwlwifi/iwl-5000.c
drivers/net/wireless/iwlwifi/iwl-agn.c
drivers/net/wireless/iwlwifi/iwl-core.c
drivers/net/wireless/iwlwifi/iwl-eeprom.c
drivers/net/wireless/iwlwifi/iwl-hcmd.c
drivers/net/wireless/iwlwifi/iwl-power.c
drivers/net/wireless/iwlwifi/iwl3945-base.c
This patch removes the said #include <version.h>.
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
txdone_entry_desc_flags is used with __set_bit and test_bit which
bit-shift the values, so don't bit-shift the flags in the enum.
Also make sure flags are initialized before being used.
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In trying to help users on the Ubuntu Bugzilla, I discovered another
BCM4306 with the Bluetooth Coexistence programming error in the SPROM.
This patch is contingent on the one that added the Linksys device with
subdevice code of 0x0014.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
(Only important for USB V1 Adaptors)
If an incoming frame wasn't accepted by p54_rx function
the skb will be reused for new frames...
But, we must not forget to set the skb's data pointers into
the same state in which it was initialized by p54u_init_urbs.
Otherwise we either end up with 16 bytes less on every requeue,
or if a new frame is worthy enough to be accepted, the data is
in the wrong place (urb->transfer_buffer wasn't updated!) and mac80211
has a hard time to recognize it...
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
priv->tx_hdr_len is set by the driver _after_ it called p54_init_common.
While this isn't much a problem for any PCI or ISL3887 cards/sticks,
because they don't need any extra header and therefore tx_hdr_len is
zero for them...
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add newlines at printk outputs to not break dmesg.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Zhu Yi <yi.zhu@intel.com>
Cc: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add the USB ID for a Netgear WG111v3.
Signed-off-by: matthieu Barthélemy <bonsouere@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The Linksys WMP54G (BCM4306/3) card in a PCI format has an SPROM coding
error and needs the fix found for several other cards.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@kernel.org> [2.6.25.x, 2.6.26.x]
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit 256b152b00 (ath5k: don't enable
MSI, we cannot handle it yet) has removed msi support, but overlooked
the suspend/resume code. This patch completes msi removal.
I don't consider this patch copyrightable, and thus put it into the
public domain. The result is of course a base.c file dual-licensed under
3-clause-BSD and GPL.
Signed-off-by: Michael Karcher <kernel@mkarcher.dialup.fu-berlin.de>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit b19fa1f, entitled "net: Delete NETDEVICES_MULTIQUEUE kconfig
option" breaks p54pci and p54usb.
Additionally, the old logic always tx'ed cts frames (if enabled)
with a short preamble when [rate > 3]. (i.e. with any 802.11g rate).
Of course this isn't that bad, but it's still wrong!
(This patch also clarifies the meanings of some of the fields in the tx
header for the hardware. -- JWL)
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: <stable@kernel.org> [2.6.25.x, 2.6.26.x]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
(I missed the fact that the original post said to apply this patch
twice... -- JWL)
Original commit log message:
This patch works around an internal compiler error (gcc bug #37014) in
all gcc 4.2 compilers and the gcc 4.3 series up to at least 4.3.1
on at least powerpc and mips.
Many thanks to Andrew Pinski for analyzing the gcc bug.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use a single enum for managing modes, store supported modes by
the HW in a bitmask.
Register legacy rates with mac80211 only at init.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use ath9k_tx_queue_info which contains the same elements,
and merge get/set functions of tx queue properties.
Also, fix whitespace damage in struct ath_softc.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch works around an internal compiler error (gcc bug #37014) in
all gcc 4.2 compilers and the gcc 4.3 series up to at least 4.3.1
on at least powerpc and mips.
Many thanks to Andrew Pinski for analyzing the gcc bug.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds the new mac80211 11n ath9k Atheros driver. Only STA support
is currently enabled and tested.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Jack Howarth <howarth@bromo.msbb.uc.edu>
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove Atheros 11n devices from being claimed by ath5k as its
now handled by ath9k.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
these "magic" values must to be the other way round...
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It was possible for unsupported operating modes
to be accepted by the add_interface callback function.
This patch will block those modes until proper support
has been implemented for them.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Following "mac80211: fix TX sequence numbers", if a packet
has the IEEE80211_TX_CTL_ASSIGN_SEQ assigned, a sequence number must be
supplied, either by hardware or software. AFAIK, no such hardware exists
for the p54, thus it must be done in software. With this patch, a connection
qith p54usb is stable, whereas the interface went off-line in 2-3 hours
without this change. Note that this code will have to be reworked for proper
sequence numbers on beacons. In addition, the sequence number has been placed
in the hardware state, not the vif state.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch cleans up iwl_tx_skb function.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some hardware set promisc when they are requested to set IFF_ALLMULTI flag.
It's ok, but if drivers set IFF_PROMISC flag when they set promisc,
it will broken upper layer handle for promisc and allmulti.
In addition, drivers can use their own hardware programming to make it.
So do not allow drivers to set IFF_* flags.
This is a general driver fix, so I didn't split it to pieces and send
to specific driver maintainers.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
We should allow packets transmission in monitor mode for 3945. The
patch fixes a merge error with 2.6.26 kernel.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We need to grap nic access before accessing periphery registers.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch decrements rx skb counter in scan abort handler.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes unhandled interrupt when HW rfkill is on during
devices start up. The behavior changes, now open is successful even
when rfkill is on. This is to align with the situation when rfkill
is set on after opening.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch implements rssi calculation for 5000 HW.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch optimizes memory allocation. The cmd member of
iwl_tx_queue was allocated previously as a continuous block
of memory. This patch allocates separate memory chunks for each command
and maps/unmaps these chunks in the run time.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds few HW bug fixes.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Experience with the rtl8187 driver has shown that mac80211 can make
calls to the config callback routine in rapid succession. This patch
creates a mutex that protects the private data in several of the routines
called by mac80211.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the legacy rt2570 driver the link tuner was never
really called. And now the reason has finally become
apparent: It breaks TX capabilities
As soon as the device has been associated all following
TX frames will be queued in the hardware and never transmitted
to the air. Disabling sections of the link tuner did not
have the expected result, but completely disabling the
link tuner did have the right result (Both of my rt2570 devices
came back to life).
This should fix Fedora bug: 411481
v2: Fix typos
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Having the buffer on the stack and even re-using it for all led devices is bad.
Not being able to resolve the name member of the led device structure to a
meaningful value leads to confusion during ad-hoc debugging and potential
breakage in the future, if we ever decide to access the name member outside of
the registration function. Move the buffer to our private per led device
structures so that it is accessible after registration.
A quick grep didn't yield any occurence of using the led device name parameter
outside of the led device registration function, so currently we should already
be safe for normal operation.
Signed-off-by: Sven Wegener <sven.wegener@stealer.net>
Cc: Richard Purdie <rpurdie@rpsys.net>
Acked-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch renames driver name from 4965 to AGN
The driver supports both 4965AGN and 5000AGN family
The driver's original module name iwl4965.ko remains as an alias
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes errors reported by checkpatch in iwlwifi drivers
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch renames iwl4965-base.c to iwl-agn.c
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch uses dtim_period from association, and sets the listen_interval.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwl-agn-rs.c: In function 'rs_clear':
iwl-agn-rs.c:2405: warning: unused variable 'priv
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a bug in AGG flow:
u64 bitmap = 0;
bitmap |= 1 << 32 results to be 0xffffffff80000000.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch sets the led register in disassociation flow according to
rf-kill state : off - in case of rf_kill, on - otherwise.
Signed-off-by: Esti Kummer <ester.kummer@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwl4965_fill_rs_info was used in sysfs. This info is already present
in iwl-agn-rs debugfs.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch renames iwl-4965-rs to iwl-agn-rs as it provides
rate scale capability for all AGN capable iwlwifi drivers.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch moves iwl4965_set_pwr_src to iwl4965-base.c.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch concentrates becaon handling in iwl4965-base.c.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch moves iwl4965_mac_ampdu_action to iwl4965-base.c.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch corrects power_level in sysfs.
Signed-off-by: Esti Kummer <ester.kummer@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support for power save for 5000 HW.
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2x00usb_vendor_request_large_buff is write-only, so it is
safe to make the argument a const.
Fixes compile warning:
drivers/net/wireless/rt2x00/rt73usb.c: In function 'rt73usb_load_firmware':
drivers/net/wireless/rt2x00/rt73usb.c:916: warning: passing argument 5 of 'rt2x00usb_vendor_request_large_buff' discards qualifiers from pointer target typ
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some module parameters with only one line have the '\n' at the end of the
description. This is not needed nor wanted as after the description the
type (i.e. int) is followed by a newline.
Some modules contain a multi-line description, these are not affected
by this patch.
Signed-off-by: Niels de Vos <niels.devos@wincor-nixdorf.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: Ed L. Cashin <ecashin@coraid.com>
Cc: Dave Airlie <airlied@linux.ie>
Cc: Roland Dreier <rolandd@cisco.com>
Acked-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
iwl3945_rx_reply_rx was sending packets too early to
mac80211, before updating signal strength/quality.
This resulted in garbage power levels.
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the standard offsetof() macro to fix a compile warning below:
CC [M] drivers/net/wireless/prism54/isl_ioctl.o
drivers/net/wireless/prism54/isl_ioctl.c: In function 'prism2_ioctl_set_generic_element':
drivers/net/wireless/prism54/isl_ioctl.c:2658: warning: cast from pointer to integer of different size
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ipw_write8() can't be used alone with a loop because of a wrong definition.
CC [M] drivers/net/wireless/ipw2200.o
drivers/net/wireless/ipw2200.c: In function 'ipw_ethtool_set_eeprom':
drivers/net/wireless/ipw2200.c:10579: warning: array subscript is above array bounds
drivers/net/wireless/ipw2200.c: In function 'ipw_load':
drivers/net/wireless/ipw2200.c:2663: warning: array subscript is above array bounds
Add missing do {} while (0) to fix them.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some users of the RTL8187B have experienced difficulties since commit
49292d5635 that introduced the power
management wext hooks. This difficulty has not made much sense until
it was realized that it was possible for mac80211 to make a call to the
config routine while that routine was already being executed. On this
device, it is necessary to loopback the TX when changing channels. Unless
this is properly restored, the device will lockup. A mutex now protects
the device state, and the private data in several places.
The problem was found by Herton Ronaldo Krzesinski <herton@mandriva.com.br>,
who also suggested this type of fix.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Acked-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In kernel version 2.6.26-rc9 my wireless LAN card worked; but in the
released 2.6.26, my RaLink rt2500 card wouldn't associate.
Git-bisect led me to this patch:
61486e0f68
rt2x00: Remove ieee80211_tx_control argument from write_tx_desc()
I believe that there is a problem with that patch --- it
(inadvertantly) removes an extra line of code, that used to set the
DATABYTE_COUNT field.
This patch reinstates that line, and with it my card works again.
Signed-off-by: Peter Chubb <peterc@gelato.unsw.edu.au>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since only mesh-enabled firmware has the CMD_802_11_MONITOR_MODE on
which the rtap functionality depends, only expose the rtap functionality
when mesh is also available.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The sequence counter can be accessed in IRQ context,
which means the lock protecting the counter should
be irqsave. To prevent making the entire intf->lock irqsave
without reason, create a new lock which only protects
the sequence counter.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the EEPROM_BBPTUNE_VGC word is valid, we should
override EEPROM_BBPTUNE_VGCLOWER field with the BBP
value.
And we should _not_ do that when EEPROM_BBPTUNE_R17 is valid.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After the hardware has indicated the firmware upload has completed
and the device is ready, we should wait another millisecond to
make sure the device is really ready to continue.
Without this timout, bringing the interface down and up again will
fail due to incorrect register initialization.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The if-statement to determine the new TX/RX antenna
configuration was incomplete. It lacks the general
else-clause when the antenna wasn't changed.
This is a correct event, since it can occur when only
one of the antenna's has been changed or when the new
configuration is being forced (like when the interface
has just been added).
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Although most rt2x00 debugfs files don't contain
information which could compromise network security,
it is better to set the access permissions to root only.
This will be required when HW crypto is implemented,
because it could be possible to read the HW key from
the registers.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch avoids stopping queue in the middle of the fragmented packet.
It is required that there will be ~10 (max packet/min fragment) or 16
(4 bits of frag number) free tfds all the time.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mask out previously demanded interrupt flags because we set
new ones. Don't allow mixing them after switch from sta to
ibss and vice versa.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Nick Kossifidis <mickflemm@gmail.com>
Cc: Luis R. Rodriguez <mcgrof@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Enable I/Q calibration each time we have correction results (we
were only enabling calibration during reset). If we don't we commit
the same results each time calibration routine is called.
* Add some documentation and a TODO on nf calibration
* Return -EAGAIN on noise floor timeout/failure
Changes-licensed-under: ISC
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Add channel function for RF2425 (got this from decompiling binary
HAL, i have no idea why there is a 5GHz section but i'm looking
into it)
* Update RF5112 channel function (also got this from decompiling binary HAL)
* Set JAPAN setting for channel 14 on all PHY chips
Changes-licensed-under: ISC
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Add initial RF gain settings for RF2425
Changes-licensed-under: ISC
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Update ath5k_hw_reset and add some more documentation about PHY calibration
* Fix ath5k_hw_set_power to use AR5K_SLEEP_CTL_SLE_ALLOW for Network sleep
* Preserve sleep duration field while setting AR5K_SLEEP_CTL
and reduce delays & checks for register's status (got this from
decompiling & dumps, it works for me but it needs testing)
Changes-licensed-under: ISC
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Do an ADC test during reset to match recent regdumps
Changes-licensed-under: ISC
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Update hw_reset to calculate some of the values we were using as static
* Increase activation to rx delay
Changes-licensed-under: ISC
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Correctly attach RF2425
* Update SREV values for Radio chips
* Update hw_attach to use new SPENDING values
* Write a bit after POST for some chips
Changes-licensed-under: ISC
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Restore saved initial value after POST
Changes-licensed-under: ISC
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Update list of registers
* Use updated register macros inside hw.c, initvals.c and debug.c
Changes-licensed-under: ISC
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes mac80211 to not use the skb->cb over the queue step
from virtual interfaces to the master. The patch also, for now,
disables aggregation because that would still require requeuing,
will fix that in a separate patch. There are two other places (software
requeue and powersaving stations) where requeue can happen, but that is
not currently used by any drivers/not possible to use respectively.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wireless statistics produced by the RTL8187B driver are not particularly
informative about the strength of the received signal. From the data sheet
provided by Realtek, I discovered that certain parts of the RX header
should have the information necessary to calculate signal quality and
strength. With testing, it became clear that most of these quantities were
very jittery - only the AGC correlated with the signals expected from nearby
AP's. As a result, the quality and strength are derived from the agc value.
The scaling has been determined so that the numbers are close to those
obtained by b43 under the same conditions. The results are qualitatively
correct.
Statistics derived for the RTL8187 have not been changed.
The RX header variables have been renamed to match the quantites described
in the Realtek data sheet.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"mac80211: fix TX sequence numbers" broke rtl8187. This
patch makes the same kind of fix that was done for rt2x00. Note that
this code will have to be reworked for proper sequence numbers on beacons.
In addition, the sequence number has been placed in the hardware state,
not the vif state.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
drivers/net/wireless/mac80211_hwsim.c:503:20: warning: Using plain integer as NULL pointer
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ia64:
drivers/net/wireless/iwlwifi/iwl-led.c: In function `iwl_get_blink_rate':
drivers/net/wireless/iwlwifi/iwl-led.c:271: warning: long long int format, s64 arg (arg 6)
drivers/net/wireless/iwlwifi/iwl-led.c:271: warning: long long int format, u64 arg (arg 7)
We do not know what type the architecture uses to impement u64 and s64,
hence we must cast the variables for printing.
Cc: Tomas Winkler <tomas.winkler@intel.com>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the queues are being initialized the entry flags fields must be
reset to 0. When this does not happen some entries might still be
marked as "occupied" after an ifdown & ifup cycle which would trigger
errors when the entry is being accessed:
phy0 -> rt2x00queue_write_tx_frame: Error - Arrived at non-free entry in the non-full queue 0.
Please file bug report to http://rt2x00.serialmonkey.com.
This also fixes the mac80211 warning:
------------[ cut here ]------------
WARNING: at net/mac80211/tx.c:1238 ieee80211_master_start_xmit+0x30a/0x350 [mac80211]()
which was triggered by the queue error.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2x00 will only perform configuration changes from
mac80211 when the configuration option has changed.
This means it keeps track of the current active configuration
and will check these values when the config() callback function
is used.
However this causes breakage when the interface has been
brought down and up again, since all stored active values
aren't reset while the registers might have.
This is for example the case with rt61pci antenna registers which
will jump to invalid values when the interface has been started.
To make sure a full configuration takes place after the start()
callback function, a new flag is added which will be checked
during config() and skips the "what's changed" phase.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The mutex is released on a successful return, so it would seem that it
should be released on an error return as well.
The semantic patch finds this problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
expression l;
@@
mutex_lock(l);
... when != mutex_unlock(l)
when any
when strict
(
if (...) { ... when != mutex_unlock(l)
+ mutex_unlock(l);
return ...;
}
|
mutex_unlock(l);
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Cc: stable <stable@kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The mutex is released on a successful return, so it would seem that it
should be released on an error return as well.
The semantic patch finds this problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
expression l;
@@
mutex_lock(l);
... when != mutex_unlock(l)
when any
when strict
(
if (...) { ... when != mutex_unlock(l)
+ mutex_unlock(l);
return ...;
}
|
mutex_unlock(l);
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When sending the RTS/CTS frame fails, we should
free the skb buffer which was created.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When IEEE80211_TX_CTL_ASSIGN_SEQ is not set,
the driver should disable hardware sequence counting
to make sure the mac80211 provided counter is used.
This fixes QOS sequence counting, since that is one
of the cases where mac80211 provides a seperate
sequence counter.
By moving the sequence counting code to rt2x00queue
we make sure that _all_ frames get the sequence counter,
including RTS/CTS and Beacon frames.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When setting up a beacon template, the length of the beacon is
calculated with the assumption that the SKB already contains
the Tx descriptor. In the case of beacons it doesn't.
This patch undoes the damage by adding the Tx descriptor length
to the beacon length. This is safe, because the shortest possible
beacon is longer than the Tx header.
Signed-off-by: Iwo Mergler <Iwo@call-direct.com.au>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Switches rt73usb to use large vendor requests for firmware
and beacons. This also fixes the garbled beacon bug.
Signed-off-by: Iwo Mergler <Iwo@call-direct.com.au>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Adds an extra rt2x00 vendor request function to support register
transfers beyond the CSR_CACHE_SIZE / USB packet size limit. This
is useful for firmware uploads, beacon templates and keys, all
of which are to large to do with a single USB request.
Signed-off-by: Iwo Mergler <Iwo@call-direct.com.au>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Olivier reported a difference between the EIFS
values used in the legacy driver and the one in
the rt2x00 drivers.
In rt2x00 the value was
( SIFS + (8 * (IEEE80211_HEADER + ACK_SIZE)) )
which comes down to 314us while the legacy driver uses the value 364us
This was caused because EIFS is: SIFS + DIFS + AckTime
This patch will fix this by adding the DIFS by the above value,
and creating a SHORT_EIFS define which uses the SHORT_DIFS.
Reported-by: Olivier Cornu <o.cornu@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
MSI is a nice thing, but we cannot enable it without changing the
interrupt handler. If we do it, we break MSI capable hardware,
specifically AR5006 chipset.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath5k_beacon_update takes sc->lock upon entry. However, it is only
called from within ath5k_config_interface, which already holds the lock.
Remove the unnecessary locking from ath5k_beacon_update.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CC [M] drivers/net/wireless/iwlwifi/iwl-scan.o
drivers/net/wireless/iwlwifi/iwl-scan.c: In function 'iwl_rx_scan_complete_notif':
drivers/net/wireless/iwlwifi/iwl-scan.c:274: warning: unused variable 'scan_notif'
Signed-off-by: Denis V. Lunev <den@openvz.org>
Acked-by: Tomas Winkler <tomasw@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CC [M] drivers/net/wireless/iwlwifi/iwl-rfkill.o
drivers/net/wireless/iwlwifi/iwl-led.c: In function 'iwl_led_brightness_set':
drivers/net/wireless/iwlwifi/iwl-led.c:198: error: 'led_type_str' undeclared (first use in this function)
drivers/net/wireless/iwlwifi/iwl-led.c:198: error: (Each undeclared identifier is reported only once
drivers/net/wireless/iwlwifi/iwl-led.c:198: error: for each function it appears in.)
The problem is that led_type_str is defined under CONFIG_IWLWIFI_DEBUG
while IWL_DEBUG is a static inline function in this case. Replace it
with macro.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some persistent settings were using hex and others decimal. In some cases,
values were set in hex but reported in decimal. Confusing.
Signed-off-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When building the wireless-next-2.6 tree with CONFIG_IWL3945 (for building
iwl-3945 driver) and where CONFIG_IWL3945_LEDS is not set,
we get this warning:
drivers/net/wireless/iwlwifi/iwl-3945.c: In function
'iwl3945_pass_packet_to_mac80211':
drivers/net/wireless/iwlwifi/iwl-3945.c:633: warning: unused variable 'hdr'
This patch adds #ifdef to iwl3945_pass_packet_to_mac80211() to avoid this
warning. (The variable 'hdr' is used only if CONFIG_IWL3945_LEDS is set)
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helge Deller reports that HP laptops (NC4010 and NC6000) use active-
high signals to turn on the LEDs. Previous code used active-low for
all devices.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
- free and re-request irq since it might have changed during suspend
- disable and enable msi
- don't set D0 state of the device, it's already done by the PCI layer
- do restore_state before enable_device, it's safer
- check ath5k_init return value
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Cc: Luis R. Rodriguez <mcgrof@gmail.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don't sync
- coherent mapping (descriptors)
- before unmap, it's useless
- (wrongly anyway -- for_cpu) beacon skb, it's just mapped,
so by the device yet
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Cc: Luis R. Rodriguez <mcgrof@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make sure that the irq is not in progress after stop. This means
two things:
- ensure the intr setting register is set by flushing posted values
- call synchronize_irq() after that
Also flush stop tx write, inform callers of the tx stop about still
pending transfers (unsuccessful stop) and finally don't wait another
3ms in ath5k_rx_stop, since ath5k_hw_stop_rx_dma ensures transfer to
be finished.
Make sure all writes will be ordered in respect to locks by mmiowb().
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Cc: Luis R. Rodriguez <mcgrof@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don't forget to kill tasklets on stop to not panic if they
fire after freeing some structures.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Cc: Luis R. Rodriguez <mcgrof@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When signal is noisy, hardware can use all RX buffers and since the last
entry in the list is self-linked, it overwrites the entry until we link
new buffers.
Ensure that we don't free this last one until we are 100% sure that it
is not used by the hardware anymore to not cause memory curruption as
can be seen below.
This is done by checking next buffer in the list. Even after that we
know that the hardware refetched the new link and proceeded further
(the next buffer is ready) we can finally free the overwritten buffer.
We discard it since the status in its descriptor is overwritten (OR-ed
by new status) too.
=============================================================================
BUG kmalloc-4096: Poison overwritten
-----------------------------------------------------------------------------
INFO: 0xffff810067419060-0xffff810067419667. First byte 0x8 instead of 0x6b
INFO: Allocated in dev_alloc_skb+0x18/0x30 age=1118 cpu=1 pid=0
INFO: Freed in skb_release_data+0x85/0xd0 age=1105 cpu=1 pid=3718
INFO: Slab 0xffffe200019d0600 objects=7 used=0 fp=0xffff810067419048 flags=0x40000000000020c3
INFO: Object 0xffff810067419048 @offset=4168 fp=0xffff81006741c120
Bytes b4 0xffff810067419038: 4f 0b 02 00 01 00 00 00 5a 5a 5a 5a 5a 5a 5a 5a O.......ZZZZZZZZ
Object 0xffff810067419048: 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b kkkkkkkkkkkkkkkk
Object 0xffff810067419058: 6b 6b 6b 6b 6b 6b 6b 6b 08 42 30 00 00 0b 6b 80 kkkkkkkk.B0...k.
Object 0xffff810067419068: f0 5d 00 4f 62 08 a3 64 00 0c 42 16 52 e4 f0 5a 360].Ob.243d..B.R344360Z
Object 0xffff810067419078: 68 81 00 00 7b a5 b4 be 7d 3b 8f 53 cd d5 de 12 h...{245264276};.S315325336.
Object 0xffff810067419088: 96 10 0b 89 48 54 23 41 0f 4e 2d b9 37 c3 cb 29 ....HT#A.N-2717303313)
Object 0xffff810067419098: d1 e0 de 14 8a 57 2a cc 3b 44 0d 78 7a 19 12 15 321340336..W*314;D.xz...
Object 0xffff8100674190a8: a9 ec d4 35 a8 10 ec 8c 40 a7 06 0a 51 a7 48 bb 2513543245250.354.@247..Q247H273
Object 0xffff8100674190b8: 3e cf a1 c7 38 60 63 3f 51 15 c7 20 eb ba 65 30 >ϡ3078`c?Q.307.353272e0
Redzone 0xffff81006741a048: bb bb bb bb bb bb bb bb 273273273273273273273273
Padding 0xffff81006741a088: 5a 5a 5a 5a 5a 5a 5a 5a ZZZZZZZZ
Pid: 3297, comm: ath5k_pci Not tainted 2.6.26-rc8-mm1_64 #427
Call Trace:
[<ffffffff802a7306>] print_trailer+0xf6/0x150
[<ffffffff802a7485>] check_bytes_and_report+0x125/0x180
[<ffffffff802a75dc>] check_object+0xac/0x260
[<ffffffff802a9308>] __slab_alloc+0x368/0x6d0
[<ffffffff80544f82>] ? wireless_send_event+0x142/0x310
[<ffffffff804b1bd4>] ? __alloc_skb+0x44/0x150
[<ffffffff80544f82>] ? wireless_send_event+0x142/0x310
[<ffffffff802aa853>] __kmalloc_track_caller+0xc3/0xf0
[<ffffffff804b1bfe>] __alloc_skb+0x6e/0x150
[... stack snipped]
FIX kmalloc-4096: Restoring 0xffff810067419060-0xffff810067419667=0x6b
FIX kmalloc-4096: Marking all objects used
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Cc: Luis R. Rodriguez <mcgrof@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I forgot this in the previous patch that made it unused.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add per-device dma_mapping_ops support for CONFIG_X86_64 as POWER
architecture does:
This enables us to cleanly fix the Calgary IOMMU issue that some devices
are not behind the IOMMU (http://lkml.org/lkml/2008/5/8/423).
I think that per-device dma_mapping_ops support would be also helpful for
KVM people to support PCI passthrough but Andi thinks that this makes it
difficult to support the PCI passthrough (see the above thread). So I
CC'ed this to KVM camp. Comments are appreciated.
A pointer to dma_mapping_ops to struct dev_archdata is added. If the
pointer is non NULL, DMA operations in asm/dma-mapping.h use it. If it's
NULL, the system-wide dma_ops pointer is used as before.
If it's useful for KVM people, I plan to implement a mechanism to register
a hook called when a new pci (or dma capable) device is created (it works
with hot plugging). It enables IOMMUs to set up an appropriate
dma_mapping_ops per device.
The major obstacle is that dma_mapping_error doesn't take a pointer to the
device unlike other DMA operations. So x86 can't have dma_mapping_ops per
device. Note all the POWER IOMMUs use the same dma_mapping_error function
so this is not a problem for POWER but x86 IOMMUs use different
dma_mapping_error functions.
The first patch adds the device argument to dma_mapping_error. The patch
is trivial but large since it touches lots of drivers and dma-mapping.h in
all the architecture.
This patch:
dma_mapping_error() doesn't take a pointer to the device unlike other DMA
operations. So we can't have dma_mapping_ops per device.
Note that POWER already has dma_mapping_ops per device but all the POWER
IOMMUs use the same dma_mapping_error function. x86 IOMMUs use device
argument.
[akpm@linux-foundation.org: fix sge]
[akpm@linux-foundation.org: fix svc_rdma]
[akpm@linux-foundation.org: build fix]
[akpm@linux-foundation.org: fix bnx2x]
[akpm@linux-foundation.org: fix s2io]
[akpm@linux-foundation.org: fix pasemi_mac]
[akpm@linux-foundation.org: fix sdhci]
[akpm@linux-foundation.org: build fix]
[akpm@linux-foundation.org: fix sparc]
[akpm@linux-foundation.org: fix ibmvscsi]
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Muli Ben-Yehuda <muli@il.ibm.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Avi Kivity <avi@qumranet.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
netif_carrier_{on,off}() handles starting and stopping packet
flow into the driver. So there is no reason to invoke netif_stop_queue()
and netif_wake_queue() in response to link status events.
Signed-off-by: David S. Miller <davem@davemloft.net>
The new address list lock needs to handle the same device layering
issues that the _xmit_lock one does.
This integrates work done by Patrick McHardy.
Signed-off-by: David S. Miller <davem@davemloft.net>
I was looking at this out of interest, but I'm in no way familiar with
the code.
Looks to me that the error handling code in mac80211_hwsim is awkward.
Which leads to it calling ieee80211_unregister_hw even when
ieee80211_register_hw failed.
The function has a for loop where it generates all simulated radios.
when something fails, the error handling will call mac80211_hwsim_free
which frees all simulated radios who's pointer isn't zero. However the
information stored is insufficient to determine whether or not the call
to ieee80211_register_hw succeeded or not for a specific radio. The
included patch makes init_mac80211_hwsim clean up the current simulated
radio, and then calls into mac80211_hwsim_free to clean up all the
radios that did succeed.
This however doesn't explain why the rate control registration failed..
build tested this, but had some problems reproducing the original
problem.
Signed-off-by: Ian Schram <ischram@telenet.be>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (1232 commits)
iucv: Fix bad merging.
net_sched: Add size table for qdiscs
net_sched: Add accessor function for packet length for qdiscs
net_sched: Add qdisc_enqueue wrapper
highmem: Export totalhigh_pages.
ipv6 mcast: Omit redundant address family checks in ip6_mc_source().
net: Use standard structures for generic socket address structures.
ipv6 netns: Make several "global" sysctl variables namespace aware.
netns: Use net_eq() to compare net-namespaces for optimization.
ipv6: remove unused macros from net/ipv6.h
ipv6: remove unused parameter from ip6_ra_control
tcp: fix kernel panic with listening_get_next
tcp: Remove redundant checks when setting eff_sacks
tcp: options clean up
tcp: Fix MD5 signatures for non-linear skbs
sctp: Update sctp global memory limit allocations.
sctp: remove unnecessary byteshifting, calculate directly in big-endian
sctp: Allow only 1 listening socket with SO_REUSEADDR
sctp: Do not leak memory on multiple listen() calls
sctp: Support ipv6only AF_INET6 sockets.
...
This reverts commit 94d9842403.
Alan says it's not appropriate to remove this driver,
Adrian Bunk also agrees with this revert.
Signed-off-by: David S. Miller <davem@davemloft.net>
alloc_netdev_mq() now allocates an array of netdev_queue
structures for TX, based upon the queue_count argument.
Furthermore, all accesses to the TX queues are now vectored
through the netdev_get_tx_queue() and netdev_for_each_tx_queue()
interfaces. This makes it easy to grep the tree for all
things that want to get to a TX queue of a net device.
Problem spots which are not really multiqueue aware yet, and
only work with one queue, can easily be spotted by grepping
for all netdev_get_tx_queue() calls that pass in a zero index.
Signed-off-by: David S. Miller <davem@davemloft.net>
There are a lot of crappy controllers out there that cannot handle
all the request sizes that the MMC/SD/SDIO specifications require.
In case the card driver can pad the data to overcome the problems,
this commit adds a helper that calculates how much that padding
should be.
A corresponding helper is also added for SDIO, but it can also deal
with all the complexities of splitting up a large transfer efficiently.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
When I removed the special "default" meaning from the QoS
parameters, I forgot to update drivers and this lead to
warnings because some drivers were checking for the special
values and putting in defaults. This fixes that by removing
the default special-casing completely.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have a specific lock to protect the network
device unicast and multicast lists, remove extraneous
grabs of the TX lock in cases where the code only needs
address list protection.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add netif_addr_{lock,unlock}{,_bh}() helpers.
Use them to protect operations that operate on or read
the network device unicast and multicast address lists.
Also use them in cases where the code simply wants to
block calls into the driver's ->set_rx_mode() and
->set_multicast_list() methods.
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the legacy drivers the LED association status
must be reset after the firmware has been uploaded to the
hardware.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is a small fix to change the idx type from int to unsigned.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch fixes LEDs problem for 3945.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch fixes the problem that TXPOWER command is not sent
after we issue a new RXON command which requires a tune. Otherwise
we won't be able to Tx any frames.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch enables active scan on active channels.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch unifies 4965 and 5000 scanning code.
We increases the version number to 1.3.27. Since new uCode
iwlwifi-4965-2.ucode is required for 4965 cards.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch makes correct usage of the LED blink table.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes LED stall. last_blink_time was updated only if LED command
was sent, causing wrong computation of the througput.
Some code cleanup comes with this patch as well
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch asks to allocate the correct amount of sw queues according
to hw ampdu queues number.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes iwl4965_mac_conf_tx. A mutex was taken in atomic context
leading to Oops. This patch removes the mutex and extends the hold
priv->lock. None of the field of QOS is accessed without priv->lock held.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes printk NULL pointer exceptions in rs code.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Guy Cohen <guy.cohen@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes post associate work. It wasn't used.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes the RTS / CTS support in iwlwifi. 5000 will send CTS to
self when allowed by spec, 4965 will send RTS or CTS to self according to
mac80211 request.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch adds PCI device IDs to iwl_hw_card_ids.
Signed-off-by: Esti Kummer <stkumer@localhost.localdomain>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac802 can handle duplicate packages on its own, so let it do it.
The patch is based on patch from Johannes Berg for iwl4965.
Signed-off-by: Adel Gadllah <adel.gadllah@gmail.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use directly put_unaligned_leX instead of put_unaligned(cpu_to_leX
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Radiotap is entirely little endian. Found with sparse.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch makes mac80211 assign proper sequence numbers to
QoS-data frames. It also removes the old sequence number code
because we noticed that only the driver or hardware can assign
sequence numbers to non-QoS-data and especially management
frames in a race-free manner because beacons aren't passed
through mac80211's TX path.
This patch also adds temporary code to the rt2x00 drivers to
not break them completely, that code will have to be reworked
for proper sequence numbers on beacons.
It also moves sequence number assignment down in the TX path
so no sequence numbers are assigned to frames that are dropped.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For RTL8187B it seems we need special values too for ANAPARAM*_OFF
values (and not use RTL8187 ones). The ANAPARAM*_OFF values used are the
stock ones read from the hardware after a cold boot.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the new beacon handling from mac80211 we can
reorganize the beacon handling in rt2x00 as well.
This patch will move the function to the TX handlers,
and move all duplicate code into rt2x00queue.c.
After this change the descriptor helper functions
from rt2x00queue.c no longer need to be exported
outside of rt2x00lib and can be declared static.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Inform drivers about the changed CTS protection settings.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch changes mac80211's beacon configuration handling
to never pass skbs to the driver directly but rather always
require the driver to use ieee80211_beacon_get(). Additionally,
it introduces "change flags" on the config_interface() call
to enable drivers to figure out what is changing. Finally, it
removes the beacon_update() driver callback in favour of
having IBSS beacon delivered by ieee80211_beacon_get() as well.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When CONFIG_HOTPLUG=n the following error occures on vmlinux linkage:
`.exit.text' referenced in section `.data' of drivers/built-in.o:
defined in discarded section `.exit.text' of drivers/built-in.o
'rtl8187_disconnect' function marked as __devexit isn't compiled with no
hotplug support. Added __devexit_p macros to fix the problem.
Signed-off-by: Ihar Hrachyshka <ihar.hrachyshka@promwad.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As soon as an interface is enabled, and that interface is in adhoc or master mode,
the device will start raising beacondone interrupts. But before the first interrupt is
raised, mac80211 will probably not have send any beacons to the device yet, which
results in a NULL pointer error when the skb is being freed.
Note that the "raise beacondone interrupts without a beacon" is also a bug,
and will be addressed later. The more important bug however is preventing
the NULL pointer failt itself, since there might be other conditions that could trigger
it as well.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fixing unaligned memory access on the blackfin architecture.
Signed-off-by: Ihar Hrachyshka <ihar.hrachyshka@promwad.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If a mesh or ad-hoc interface is brought up and later it is replaced
by managed interface, the managed interface will keep transmitting
the beacons that were configured for the former interface. This patch
fixes that behaviour.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As soon as init_registers() was called, the rt2400/rt2500
would start raising beacondone interrupts. Since this is highly
premature since no beacons were provided yet, we should
initialize the synchronization register to 0.
This will make all drivers initialize it to 0 regardless
if they are raising beacondone interrupts or not, since it only
makes sense to have it completely disabled.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Accesses are mostly structured such that when there are multiple TX
queues the code transformations will be a little bit simpler.
Signed-off-by: David S. Miller <davem@davemloft.net>
Some early versions of RTL8187B devices have a USB ID of 0x8187
rather than the 0x8189 of later models. In addition, it appears
that these early units also must be programmed with lower power.
Previous patches used the Product ID string to detect this situation,
but did not address the low power question. This patch uses the
hardware version and sets the power accordingly.
Signed-off-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix some register documentation in the register header files.
This allows better parsing by userspace scripts which in turn
helps debugging.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The gcc 3.4 fork used to compile the MN10300 port emits unwanted
__ucmpdi2() calls for switch statements that use a 64bit value.
This patch removes such a switch from b43legacy, and makes the code
more like that used in b43. Thanks to Adrian Bunk <bunk@kernel.org>
for reporting the problem.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2400 is the only currently available rt2x00 driver which
supports reporting of the RX end time for frames.
Since mac80211 uses this information for IBSS syncing, it
is important that it is being reported.
v2: Complement 32 bits of RX timestamp with upper 32bits from TSF
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove the rt2x00 singlethreaded workqueue and move
the link tuner and packet filter scheduled work to
the ieee80211_hw->workqueue again.
The only exception is the interface scheduled work
handler which uses the mac80211 interface iterator
under the RTNL lock. This work needs to be handled
on the kernel workqueue to prevent lockdep issues.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We only need 4 bytes of headroom for alignment
purposes in the RX frame. It was previously higher
for optimization purposes which are no longer
possible due to DMA mappings.
v2: Fix patch error
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the new rfkill interface there is no longer a need
for the input_polldev. Create a delayed_work structure
which we can put on the mac80211 workqueue and poll the
hardware every 1000ms.
v2: Decrease poll frequency from 100ms to 1000ms
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add some error checking to the new beacon configuration code.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes the iwlwifi rfkill. It removes the input device from iwl3945,
adds support for RFKILL_STATE_HARD_BLOCKED and calls rfkill_force_state() to
update the state rather than accessing it directly.
The calls to iwl|iwl3945_rfkill_set_hw_state() had to be moved because
rfkill_force_state() cannot be called from an atomic context.
Tested on iwl3945 and seems to work fine.
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Ivo van Doorn <ivdoorn@gmail.com>
Cc: Fabien Crespel <fcrespel@gmail.com>
Cc: Zhu Yi <yi.zhu@intel.com>
Cc: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Adel Gadllah <adel.gadllah@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch sets the block ack request flag if needed
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch cleans rfkill error path. The problem was result of removing
the input device
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I would like to inform you of our zd1211 based usb wifi adapter (AirTies
WUS-201), which works with the zd1211rw driver with the following device
id definition.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Coverity CID: 2265 NEGATIVE_RETURNS
"rate" is of an unsigned type, and the code requires a signed type.
The following patch makes it so.
Signed-off-by: Darren Jenkins <darrenrjenkins@gmailcom>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The p54 driver family reports a quality of 0 in iwconfig and iwlist
output. This patch calculates a quality number as a percentage of the
rssi to the maximum signal of 127 reported as the maximum signal.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch fixes the compile warning of "enumeration value
‘RFKILL_STATE_HARD_BLOCKED’ not handled in switch".
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch fixes the temperature calibration issue introduced by the
patch "iwlwifi: move RX stats to core, and move temperature to handler".
It also remove the second parameter "stats" since it is already copied
to priv->statistics.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch enables packet injection on iwl3945 devices. Tested with
packetspammer and aireplay-ng.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes monitor mode operation for iwlwifi.
Problems addressed:
1. when monitor mode was enabled, multiple, overlapped calls were being
made to 'iwl3945_bg_set_monitor'
2. when monitor mode was disabled (via the configure_filter callback),
the driver was still enabling monitor mode
3. when monitor mode was enabled, the selected channel was not set
(eg. 'iwconfig wlanx mode monitor channel n' DID NOT SET channel 'n'
when packet capture was subsequently enabled)
Signed-off-by: Rick Farrington <rickdic@hotmail.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Handle .reset_resume() so that libertas can survive suspend/resume without
reloading the firmware.
Signed-off-by: Andrey Yurovsky <andrey@cozybit.com>
Acked-by: Deepak Saxena <dsaxena@laptop.org>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes the problem to keep mac80211 resubmitting SKBs
when Tx request cannot be met in monitor mode.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes the rates reported in monitor mode operation
(Wireshark) for iwlwifi.
Previously, packets with rates of 6M..24M would be reported
incorrectly and packets with rates of 36M..54M would not passed
up the stack.
Signed-off-by: Rick Farrington <rickdic@hotmail.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch cleans up HW RF-kill state machine.
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch makes iwl4965_mac_start block until the uCode has been
completely loaded.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes iwl4965_mac_get_tsf, as this function does not
currently reports any actual value.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds module param 11n_disable to allow configuration of 11n
capabilities. The default value of this param is 11n enabled (value 0).
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch unites common settings of 4965 and 5000 hw params.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch avoids the user from bringing up the interface if RF-kill
doesn't allow radio.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch removes the sysfs interface from iwl3945 and uses
the rfkill subsystem instead.
Original patch by Adel, I fixed the patch to work it properly.
Signed-off-by: Adel Gadllah <adel.gadllah@gmail.com>
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch makes the driver, in IBSS mode, comply with TSF requirements
in 2 ways:
1. It notifies mac80211 of its TSF timestamp.
2. It uses the given timestamp in the beacon template to update the ucode.
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch avoids unsetting STATUS_EXIT_PENDING in the middle of the
down flow.
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes regression caused by
'iwlwifi: send ADD_STA before RXON with assoc bit' patch.
RXON associated wasn't IBSS flow.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes the use of lq_ready, once used to sync between link
quality commands to avoid race conditions, but no longer needed as
bss_info_changed is in use.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch moves Rx aggregation functions into iwl-rx.c
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch sets the compressed BA handler for 5000. This allows the rate
scaling algorithm to take in count frames that were sent in AMPDUs.
The compressed BA handler has been moved to iwl-rx.c since it is common to
4965 and 5000.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The iwlwifi drivers go to great lengths to avoid passing packets to
mac80211 they think shouldn't go there, while mac80211 can (of course!)
handle them very well.
Especially in the case of duplicate packets this is interesting
because it's such a performance hog (especially for IBSS networks)
while mac80211 does that work on the side without much effort.
This patch removes all that and leaves only what is absolutely
necessary for the hardware.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch moves RX handlers to iwl-rx.c
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch avoids sending REPLY_REMOVE_ALL_STA in down flow, this avoids a
meaningless warning from being printed
On the way this patch also renames the the function to
iwl_clear_stations_table
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch moves RX stats flow to core modules, and moves temperature
calibration to handler since it is not needed in 5000.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a bug in association flow. As soon as RXON with assoc bit
is sent, uCode expects to have an entry in its station table that describe
the AP. Receiving a beacon from an HT AP before sending ADD_STA results a
uCode error. This patch sends first the ADD_STA (bcast and bssid) and only
then RXON with assoc bit set
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds REPLY_TX_POWER_DBM_CMD to get_cmd_string.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch add uses of iwl_is_associated in places it is suitable in.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch makes the station table maintenance safer. Two flags are
maintained:
1) if station is present in driver
2) if station is present in uCode
This will allow us in the future to deal with more stations than the
firmware allows.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds eeprom version display into device/version sysfs file
/sys/class/net/wlanX/devices/version
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch configures uCode to use open loop tx power algorithm
via TX_POWER_DBM (0x98) host command.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch sets the rfkill state to RFKILL_STATE_HARD_BLOCKED when the
radio is killed by the hardware switch.
Signed-off-by: Adel Gadllah <adel.gadllah@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes the usage RFKILL_STATE_ON and uses
RFKILL_STATE_UNBLOCKED instead.
Signed-off-by: Adel Gadllah <adel.gadllah@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Provide MAC time, rate, channel, signal and noise.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don't try to skip any headers in hostap_80211_header_parse(). We never
use that function for interfaces affected by local->monitor_type. Both
the master and the AP interface receive 802.11 frames without any
additional headers.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes the rfkill deps for iwl4965/5000
and removes the input device usage.
Signed-off-by: Adel Gadllah <adel.gadllah@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rewrite AID calculation in handle_pspoll() to avoid truncating bits.
Make hostap_80211_header_parse() static, don't export it. Avoid
shadowing variables.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
DEBUG_EXTRA is reported to the kernel log by default, but DEBUG_EXTRA2
is not. Unrelated WDS frames pollute the log unnecessarily.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pass buffer length to rndis_command so that rndis_command can read full
response buffer from device instead of max CONTROL_BUFFER_SIZE bytes.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Ivo van Doorn