The PCI reset GPIO is active low, so represent it with the
GPIO_ACTIVE_LOW flag.
Even though the imx6 PCI driver will not take the polarity into account
in this case, it is better to provide a correct description in device-tree.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
GPLv2-only devicetrees make reuse difficult for software components
licensed under a different license. In particular, the Utilite Pro
devicetree file (which includes imx6q-cm-fx6.dts) is already dual
licensed under GPLv2/X11.
Hence, relicense imx6q-cm-fx6.dts under GPLv2/X11 dual license.
Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The CompuLab Utilite Pro is a miniature fanless desktop pc based on
the i.MX6 Quad powered cm-fx6 module. It features two serial ports,
USB OTG, 4x USB, analog audio and S/PDIF, 2x Gb Ethernet, HDMI and
DVI ports, an on-board 32GB SSD, a mmc slot, and on-board wifi/bt.
Add initial support for it including USB, Ethernet (both ports), sata
and HDMI support.
Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The cm-fx6 module has an on-board spi-flash chip for its firmware, an
eeprom (containing e.g. the mac address of the on-board Ethernet),
a sata port, a pcie controller, an USB hub, and an USB otg port.
Enable support for them. In addition, enable syscon poweroff support.
Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The imx6q-cm-fx6 iomuxc container node is not required. Remove it.
Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This fixes the following dtc warning by removing the unnecessary unit:
Warning (unit_address_vs_reg): Node /matrix-keypad@0 has a unit name,
but no reg property
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-By: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This fixes the following dtc warning by removing the unnecessary unit:
Warning (unit_address_vs_reg): Node /onewire@0 has a unit name,
but no reg property
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch adds the missing reg properties for the regulator nodes
in order to fix the dtc warnings.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch adds the missing reg properties for the MXS GPIO banks
in order to fix the dtc warnings.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The Auvidea H100 is a baseboard for the SolidRun MicroSOM.
Its primary feature is a Toshiba TC358743 HDMI to CSI decoder,
allowing the board to work as HDMI passthrough and framegrabber.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the DT property to all boards that have the hardware workaround
for erratum ERR006687 present. This allows the CPUidle driver to use
the deep idle states, even if the FEC is active.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This node describes the DI1 port of IPU, fix the node name to reflect this.
There's currently no user of this node in mainline, so this change should
not break any supported platforms.
Signed-off-by: Juergen Borleis <jbe@pengutronix.de>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add support for the LCD8000-43T display and for the backlight
controlled via PWM1.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
As of commit 1006ed7e1b ("serial: imx: Use generic uart-has-rtscts
DT property"), the Freescale IMX UART driver recognizes the generic
"uart-has-rtscts" DT property, deprecating the vendor-specific
"fsl,uart-has-rtscts" DT property. Hence replace the latter by the
former in all DTS files.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
As of commit 182cdcb8bb ("serial: mxs-auart: Use generic
uart-has-rtscts DT property"), the Freescale MXS AUART driver recognizes
the generic "uart-has-rtscts" DT property, deprecating the
vendor-specific "fsl,uart-has-rtscts" DT property. Hence replace the
latter by the former in all DTS files.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add support for this small MP3 player based on STMP3780 (rev.3).
Currently supported are both external microSD and internal SD-NAND
bridge, PWM and USB gadget.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add support for this small MP3 player based on STMP3780 (rev.4).
Currently supported is both external microSD and internal SD-NAND
bridge, PWM and USB gadget.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add pinmux configuration for SSP2 port in SD mode, both for
the 4-bit and 8-bit case.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This enables support for the CAN controller located in the FPGA.
Signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Enable FPGA's IRQ controller. It is in charge of dispatching interrupts
generated by IPs in the FPGA. The SoC is notified that an interrupt
occurred through a GPIO.
Signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add input mux for UART2 RX in DTE mode. This allows to use the pad
UART2_TX_DATA_ALT0 as UART2 RX. This particular input select seems
to be missing in current reference manuals (Rev. B), but when looking
at the tables and other UART input select registers (e.g. UART3) it
seems naturally that this input mux register also has a fourth pad
option for UART2_TX_DATA_ALT0. It has also been proven to be required
to use UART2 in DTE mode and the particular pads on the Colibri iMX7
platform.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Pass "fsl,sai-mclk-direction-output" to the sai2 node, so that the
SAI2_MCLK can be an output.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add SAI alias entries, which makes it possibe for the SAI driver
to retrieve the port instance.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Building with W=1 option leads to several warnings like:
Warning (unit_address_vs_reg): Node /soc/aips-bus@02000000/anatop@020c8000/regulator-1p1@110 has a unit name, but no reg property
Fix them by removing the unneeded unit-addresses.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Pull kbuild updates from Michal Marek:
- new option CONFIG_TRIM_UNUSED_KSYMS which does a two-pass build and
unexports symbols which are not used in the current config [Nicolas
Pitre]
- several kbuild rule cleanups [Masahiro Yamada]
- warning option adjustments for gcov etc [Arnd Bergmann]
- a few more small fixes
* 'kbuild' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild: (31 commits)
kbuild: move -Wunused-const-variable to W=1 warning level
kbuild: fix if_change and friends to consider argument order
kbuild: fix adjust_autoksyms.sh for modules that need only one symbol
kbuild: fix ksym_dep_filter when multiple EXPORT_SYMBOL() on the same line
gcov: disable -Wmaybe-uninitialized warning
gcov: disable tree-loop-im to reduce stack usage
gcov: disable for COMPILE_TEST
Kbuild: disable 'maybe-uninitialized' warning for CONFIG_PROFILE_ALL_BRANCHES
Kbuild: change CC_OPTIMIZE_FOR_SIZE definition
kbuild: forbid kernel directory to contain spaces and colons
kbuild: adjust ksym_dep_filter for some cmd_* renames
kbuild: Fix dependencies for final vmlinux link
kbuild: better abstract vmlinux sequential prerequisites
kbuild: fix call to adjust_autoksyms.sh when output directory specified
kbuild: Get rid of KBUILD_STR
kbuild: rename cmd_as_s_S to cmd_cpp_s_S
kbuild: rename cmd_cc_i_c to cmd_cpp_i_c
kbuild: drop redundant "PHONY += FORCE"
kbuild: delete unnecessary "@:"
kbuild: mark help target as PHONY
...
This is a collection of a few late fixes and other misc. stuff that
had dependencies on things being merged from other trees.
The Renesas R-Car power domain handling, and the Nvidia Tegra USB
support both hand notable changes that required changing the DT binding
in a way that only provides compatibility with old DT blobs on new
kernels but not vice versa. As a consequence, the DT changes
are based on top of the driver changes and are now in this branch.
For NXP i.MX and Samsung Exynos, the changes in here depend on
other changes that got merged through the clk maintainer tree.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=I0Be
-----END PGP SIGNATURE-----
Merge tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC late DT updates from Arnd Bergmann:
"This is a collection of a few late fixes and other misc stuff that had
dependencies on things being merged from other trees.
The Renesas R-Car power domain handling, and the Nvidia Tegra USB
support both hand notable changes that required changing the DT
binding in a way that only provides compatibility with old DT blobs on
new kernels but not vice versa. As a consequence, the DT changes are
based on top of the driver changes and are now in this branch.
For NXP i.MX and Samsung Exynos, the changes in here depend on other
changes that got merged through the clk maintainer tree"
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (35 commits)
ARM: dts: exynos: Add support of Bus frequency using VDD_INT for exynos5422-odroidxu3
ARM: dts: exynos: Add bus nodes using VDD_INT for Exynos542x SoC
ARM: dts: exynos: Add NoC Probe dt node for Exynos542x SoC
ARM: dts: exynos: Add support of bus frequency for exynos4412-trats/odroidu3
ARM: dts: exynos: Expand the voltage range of buck1/3 regulator for exynos4412-odroidu3
ARM: dts: exynos: Add support of bus frequency using VDD_INT for exynos3250-rinato
ARM: dts: exynos: Add exynos4412-ppmu-common dtsi to delete duplicate PPMU nodes
ARM: dts: exynos: Add bus nodes using VDD_MIF for Exynos4210
ARM: dts: exynos: Add bus nodes using VDD_INT for Exynos4x12
ARM: dts: exynos: Add bus nodes using VDD_MIF for Exynos4x12
ARM: dts: exynos: Add bus nodes using VDD_INT for Exynos3250
ARM: dts: exynos: Add DMC bus frequency for exynos3250-rinato/monk
ARM: dts: exynos: Add DMC bus node for Exynos3250
ARM: tegra: Enable XUSB on Nyan
ARM: tegra: Enable XUSB on Jetson TK1
ARM: tegra: Enable XUSB on Venice2
ARM: tegra: Add Tegra124 XUSB controller
ARM: tegra: Move Tegra124 to the new XUSB pad controller binding
ARM: dts: r8a7794: Use SYSC "always-on" PM Domain
ARM: dts: r8a7793: Use SYSC "always-on" PM Domain
...
Pull drm updates from Dave Airlie:
"Here's the main drm pull request for 4.7, it's been a busy one, and
I've been a bit more distracted in real life this merge window. Lots
more ARM drivers, not sure if it'll ever end. I think I've at least
one more coming the next merge window.
But changes are all over the place, support for AMD Polaris GPUs is in
here, some missing GM108 support for nouveau (found in some Lenovos),
a bunch of MST and skylake fixes.
I've also noticed a few fixes from Arnd in my inbox, that I'll try and
get in asap, but I didn't think they should hold this up.
New drivers:
- Hisilicon kirin display driver
- Mediatek MT8173 display driver
- ARC PGU - bitstreamer on Synopsys ARC SDP boards
- Allwinner A13 initial RGB output driver
- Analogix driver for DisplayPort IP found in exynos and rockchip
DRM Core:
- UAPI headers fixes and C++ safety
- DRM connector reference counting
- DisplayID mode parsing for Dell 5K monitors
- Removal of struct_mutex from drivers
- Connector registration cleanups
- MST robustness fixes
- MAINTAINERS updates
- Lockless GEM object freeing
- Generic fbdev deferred IO support
panel:
- Support for a bunch of new panels
i915:
- VBT refactoring
- PLL computation cleanups
- DSI support for BXT
- Color manager support
- More atomic patches
- GEM improvements
- GuC fw loading fixes
- DP detection fixes
- SKL GPU hang fixes
- Lots of BXT fixes
radeon/amdgpu:
- Initial Polaris support
- GPUVM/Scheduler/Clock/Power improvements
- ASYNC pageflip support
- New mesa feature support
nouveau:
- GM108 support
- Power sensor support improvements
- GR init + ucode fixes.
- Use GPU provided topology information
vmwgfx:
- Add host messaging support
gma500:
- Some cleanups and fixes
atmel:
- Bridge support
- Async atomic commit support
fsl-dcu:
- Timing controller for LCD support
- Pixel clock polarity support
rcar-du:
- Misc fixes
exynos:
- Pipeline clock support
- Exynoss4533 SoC support
- HW trigger mode support
- export HDMI_PHY clock
- DECON5433 fixes
- Use generic prime functions
- use DMA mapping APIs
rockchip:
- Lots of little fixes
vc4:
- Render node support
- Gamma ramp support
- DPI output support
msm:
- Mostly cleanups and fixes
- Conversion to generic struct fence
etnaviv:
- Fix for prime buffer handling
- Allow hangcheck to be coalesced with other wakeups
tegra:
- Gamme table size fix"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (1050 commits)
drm/edid: add displayid detailed 1 timings to the modelist. (v1.1)
drm/edid: move displayid validation to it's own function.
drm/displayid: Iterate over all DisplayID blocks
drm/edid: move displayid tiled block parsing into separate function.
drm: Nuke ->vblank_disable_allowed
drm/vmwgfx: Report vmwgfx version to vmware.log
drm/vmwgfx: Add VMWare host messaging capability
drm/vmwgfx: Kill some lockdep warnings
drm/nouveau/gr/gf100-: fix race condition in fecs/gpccs ucode
drm/nouveau/core: recognise GM108 chipsets
drm/nouveau/gr/gm107-: fix touching non-existent ppcs in attrib cb setup
drm/nouveau/gr/gk104-: share implementation of ppc exception init
drm/nouveau/gr/gk104-: move rop_active_fbps init to nonctx
drm/nouveau/bios/pll: check BIT table version before trying to parse it
drm/nouveau/bios/pll: prevent oops when limits table can't be parsed
drm/nouveau/volt/gk104: round up in gk104_volt_set
drm/nouveau/fb/gm200: setup mmu debug buffer registers at init()
drm/nouveau/fb/gk20a,gm20b: setup mmu debug buffer registers at init()
drm/nouveau/fb/gf100-: allocate mmu debug buffers
drm/nouveau/fb: allow chipset-specific actions for oneinit()
...
Pull ARM updates from Russell King:
"Changes included in this pull request:
- revert pxa2xx-flash back to using ioremap_cached() and switch
memremap() to use arch_memremap_wb()
- remove pci=firmware command line argument handling
- remove unnecessary arm_dma_set_mask() implementation, the generic
implementation will do for ARM
- removal of the ARM kallsyms "hack" to work around mode switching
veneers and vectors located below PAGE_OFFSET
- tidy up build system output a little
- add L2 cache power management DT bindings
- remove duplicated local_irq_disable() in reboot paths
- handle AMBA primecell devices better at registration time with PM
domains (needed for Samsung SoCs)
- ARM specific preparation to support Keystone II kexec"
* 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 8567/1: cache-uniphier: activate ways for secondary CPUs
ARM: 8570/2: Documentation: devicetree: Add PL310 PM bindings
ARM: 8569/1: pl2x0: Add OF control of cache power management
ARM: 8568/1: reboot: remove duplicated local_irq_disable()
ARM: 8566/1: drivers: amba: properly handle devices with power domains
ARM: provide arm_has_idmap_alias() helper
ARM: kexec: remove 512MB restriction on kexec crashdump
ARM: provide improved virt_to_idmap() functionality
ARM: kexec: fix crashkernel= handling
ARM: 8557/1: specify install, zinstall, and uinstall as PHONY targets
ARM: 8562/1: suppress "include/generated/mach-types.h is up to date."
ARM: 8553/1: kallsyms: remove --page-offset command line option
ARM: 8552/1: kallsyms: remove special lower address limit for CONFIG_ARM
ARM: 8555/1: kallsyms: ignore ARM mode switching veneers
ARM: 8548/1: dma-mapping: remove arm_dma_set_mask()
ARM: 8554/1: kernel: pci: remove pci=firmware command line parameter handling
ARM: memremap: implement arch_memremap_wb()
memremap: add arch specific hook for MEMREMAP_WB mappings
mtd: pxa2xx-flash: switch back from memremap to ioremap_cached
ARM: reintroduce ioremap_cached() for creating cached I/O mappings
Enumeration
Refine PCI support check in pcibios_init() (Adrian-Ken Rueegsegger)
Provide common functions for ECAM mapping (Jayachandran C)
Allow all PCIe services on non-ACPI host bridges (Jon Derrick)
Remove return values from pcie_port_platform_notify() and relatives (Jon Derrick)
Widen portdrv service type from 4 bits to 8 bits (Keith Busch)
Add Downstream Port Containment portdrv service type (Keith Busch)
Add Downstream Port Containment driver (Keith Busch)
Resource management
Identify Enhanced Allocation (EA) BAR Equivalent resources in sysfs (Alex Williamson)
Supply CPU physical address (not bus address) to iomem_is_exclusive() (Bjorn Helgaas)
alpha: Call iomem_is_exclusive() for IORESOURCE_MEM, but not IORESOURCE_IO (Bjorn Helgaas)
Mark Broadwell-EP Home Agent 1 as having non-compliant BARs (Prarit Bhargava)
Disable all BAR sizing for devices with non-compliant BARs (Prarit Bhargava)
Move PCI I/O space management from OF to PCI core code (Tomasz Nowicki)
PCI device hotplug
acpiphp_ibm: Avoid uninitialized variable reference (Dan Carpenter)
Use cached copy of PCI_EXP_SLTCAP_HPC bit (Lukas Wunner)
Virtualization
Mark Intel i40e NIC INTx masking as broken (Alex Williamson)
Reverse standard ACS vs device-specific ACS enabling (Alex Williamson)
Work around Intel Sunrise Point PCH incorrect ACS capability (Alex Williamson)
IOMMU
Add pci_add_dma_alias() to abstract implementation (Bjorn Helgaas)
Move informational printk to pci_add_dma_alias() (Bjorn Helgaas)
Add support for multiple DMA aliases (Jacek Lawrynowicz)
Add DMA alias quirk for mic_x200_dma (Jacek Lawrynowicz)
Thunderbolt
Fix double free of drom buffer (Andreas Noever)
Add Intel Thunderbolt device IDs (Lukas Wunner)
Fix typos and magic number (Lukas Wunner)
Support 1st gen Light Ridge controller (Lukas Wunner)
Generic host bridge driver
Use generic ECAM API (Jayachandran C)
Cavium ThunderX host bridge driver
Don't clobber read-only bits in bridge config registers (David Daney)
Use generic ECAM API (Jayachandran C)
Freescale i.MX6 host bridge driver
Use enum instead of bool for variant indicator (Andrey Smirnov)
Implement reset sequence for i.MX6+ (Andrey Smirnov)
Factor out ref clock enable (Bjorn Helgaas)
Add initial imx6sx support (Christoph Fritz)
Add reset-gpio-active-high boolean property to DT (Petr Štetiar)
Add DT property for link gen, default to Gen1 (Tim Harvey)
dts: Specify imx6qp version of PCIe core (Andrey Smirnov)
dts: Fix PCIe reset GPIO polarity on Toradex Apalis Ixora (Petr Štetiar)
Marvell Armada host bridge driver
add DT binding for Marvell Armada 7K/8K PCIe controller (Thomas Petazzoni)
Add driver for Marvell Armada 7K/8K PCIe controller (Thomas Petazzoni)
Marvell MVEBU host bridge driver
Constify mvebu_pcie_pm_ops structure (Jisheng Zhang)
Use SET_NOIRQ_SYSTEM_SLEEP_PM_OPS for mvebu_pcie_pm_ops (Jisheng Zhang)
Microsoft Hyper-V host bridge driver
Report resources release after stopping the bus (Vitaly Kuznetsov)
Add explicit barriers to config space access (Vitaly Kuznetsov)
Renesas R-Car host bridge driver
Select PCI_MSI_IRQ_DOMAIN (Arnd Bergmann)
Synopsys DesignWare host bridge driver
Remove incorrect RC memory base/limit configuration (Gabriele Paoloni)
Move Root Complex setup code to dw_pcie_setup_rc() (Jisheng Zhang)
TI Keystone host bridge driver
Add error IRQ handler (Murali Karicheri)
Remove unnecessary goto statement (Murali Karicheri)
Miscellaneous
Fix spelling errors (Colin Ian King)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=68Iz
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.7-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"Enumeration:
- Refine PCI support check in pcibios_init() (Adrian-Ken Rueegsegger)
- Provide common functions for ECAM mapping (Jayachandran C)
- Allow all PCIe services on non-ACPI host bridges (Jon Derrick)
- Remove return values from pcie_port_platform_notify() and relatives (Jon Derrick)
- Widen portdrv service type from 4 bits to 8 bits (Keith Busch)
- Add Downstream Port Containment portdrv service type (Keith Busch)
- Add Downstream Port Containment driver (Keith Busch)
Resource management:
- Identify Enhanced Allocation (EA) BAR Equivalent resources in sysfs (Alex Williamson)
- Supply CPU physical address (not bus address) to iomem_is_exclusive() (Bjorn Helgaas)
- alpha: Call iomem_is_exclusive() for IORESOURCE_MEM, but not IORESOURCE_IO (Bjorn Helgaas)
- Mark Broadwell-EP Home Agent 1 as having non-compliant BARs (Prarit Bhargava)
- Disable all BAR sizing for devices with non-compliant BARs (Prarit Bhargava)
- Move PCI I/O space management from OF to PCI core code (Tomasz Nowicki)
PCI device hotplug:
- acpiphp_ibm: Avoid uninitialized variable reference (Dan Carpenter)
- Use cached copy of PCI_EXP_SLTCAP_HPC bit (Lukas Wunner)
Virtualization:
- Mark Intel i40e NIC INTx masking as broken (Alex Williamson)
- Reverse standard ACS vs device-specific ACS enabling (Alex Williamson)
- Work around Intel Sunrise Point PCH incorrect ACS capability (Alex Williamson)
IOMMU:
- Add pci_add_dma_alias() to abstract implementation (Bjorn Helgaas)
- Move informational printk to pci_add_dma_alias() (Bjorn Helgaas)
- Add support for multiple DMA aliases (Jacek Lawrynowicz)
- Add DMA alias quirk for mic_x200_dma (Jacek Lawrynowicz)
Thunderbolt:
- Fix double free of drom buffer (Andreas Noever)
- Add Intel Thunderbolt device IDs (Lukas Wunner)
- Fix typos and magic number (Lukas Wunner)
- Support 1st gen Light Ridge controller (Lukas Wunner)
Generic host bridge driver:
- Use generic ECAM API (Jayachandran C)
Cavium ThunderX host bridge driver:
- Don't clobber read-only bits in bridge config registers (David Daney)
- Use generic ECAM API (Jayachandran C)
Freescale i.MX6 host bridge driver:
- Use enum instead of bool for variant indicator (Andrey Smirnov)
- Implement reset sequence for i.MX6+ (Andrey Smirnov)
- Factor out ref clock enable (Bjorn Helgaas)
- Add initial imx6sx support (Christoph Fritz)
- Add reset-gpio-active-high boolean property to DT (Petr Štetiar)
- Add DT property for link gen, default to Gen1 (Tim Harvey)
- dts: Specify imx6qp version of PCIe core (Andrey Smirnov)
- dts: Fix PCIe reset GPIO polarity on Toradex Apalis Ixora (Petr Štetiar)
Marvell Armada host bridge driver:
- add DT binding for Marvell Armada 7K/8K PCIe controller (Thomas Petazzoni)
- Add driver for Marvell Armada 7K/8K PCIe controller (Thomas Petazzoni)
Marvell MVEBU host bridge driver:
- Constify mvebu_pcie_pm_ops structure (Jisheng Zhang)
- Use SET_NOIRQ_SYSTEM_SLEEP_PM_OPS for mvebu_pcie_pm_ops (Jisheng Zhang)
Microsoft Hyper-V host bridge driver:
- Report resources release after stopping the bus (Vitaly Kuznetsov)
- Add explicit barriers to config space access (Vitaly Kuznetsov)
Renesas R-Car host bridge driver:
- Select PCI_MSI_IRQ_DOMAIN (Arnd Bergmann)
Synopsys DesignWare host bridge driver:
- Remove incorrect RC memory base/limit configuration (Gabriele Paoloni)
- Move Root Complex setup code to dw_pcie_setup_rc() (Jisheng Zhang)
TI Keystone host bridge driver:
- Add error IRQ handler (Murali Karicheri)
- Remove unnecessary goto statement (Murali Karicheri)
Miscellaneous:
- Fix spelling errors (Colin Ian King)"
* tag 'pci-v4.7-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (48 commits)
PCI: Disable all BAR sizing for devices with non-compliant BARs
x86/PCI: Mark Broadwell-EP Home Agent 1 as having non-compliant BARs
PCI: Identify Enhanced Allocation (EA) BAR Equivalent resources in sysfs
PCI, of: Move PCI I/O space management to PCI core code
PCI: generic, thunder: Use generic ECAM API
PCI: Provide common functions for ECAM mapping
PCI: hv: Add explicit barriers to config space access
PCI: Use cached copy of PCI_EXP_SLTCAP_HPC bit
PCI: Add Downstream Port Containment driver
PCI: Add Downstream Port Containment portdrv service type
PCI: Widen portdrv service type from 4 bits to 8 bits
PCI: designware: Remove incorrect RC memory base/limit configuration
PCI: hv: Report resources release after stopping the bus
ARM: dts: imx6qp: Specify imx6qp version of PCIe core
PCI: imx6: Implement reset sequence for i.MX6+
PCI: imx6: Use enum instead of bool for variant indicator
PCI: thunder: Don't clobber read-only bits in bridge config registers
thunderbolt: Fix double free of drom buffer
PCI: rcar: Select PCI_MSI_IRQ_DOMAIN
PCI: armada: Add driver for Marvell Armada 7K/8K PCIe controller
...
This time round the update brings in following changes:
- New tegra driver for ADMA device
- Support for Xilinx AXI Direct Memory Access Engine and Xilinx AXI Central
Direct Memory Access Engine and few updates to this driver.
- New cyclic capability to sun6i and few updates.
- Slave-sg support in bcm2835.
- Updates to many drivers like designware, hsu, mv_xor, pxa, edma,
qcom_hidma & bam.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=0Sy7
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-4.7-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
"This time round the update brings in following changes:
- new tegra driver for ADMA device
- support for Xilinx AXI Direct Memory Access Engine and Xilinx AXI
Central Direct Memory Access Engine and few updates to this driver
- new cyclic capability to sun6i and few updates
- slave-sg support in bcm2835
- updates to many drivers like designware, hsu, mv_xor, pxa, edma,
qcom_hidma & bam"
* tag 'dmaengine-4.7-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (84 commits)
dmaengine: ioatdma: disable relaxed ordering for ioatdma
dmaengine: of_dma: approximate an average distribution
dmaengine: core: Use IS_ENABLED() instead of checking for built-in or module
dmaengine: edma: Re-evaluate errors when ccerr is triggered w/o error event
dmaengine: qcom_hidma: add support for object hierarchy
dmaengine: qcom_hidma: add debugfs hooks
dmaengine: qcom_hidma: implement lower level hardware interface
dmaengine: vdma: Add clock support
Documentation: DT: vdma: Add clock support for dmas
dmaengine: vdma: Add config structure to differentiate dmas
MAINTAINERS: Update Tegra DMA maintainers
dmaengine: tegra-adma: Add support for Tegra210 ADMA
Documentation: DT: Add binding documentation for NVIDIA ADMA
dmaengine: vdma: Add Support for Xilinx AXI Central Direct Memory Access Engine
Documentation: DT: vdma: update binding doc for AXI CDMA
dmaengine: vdma: Add Support for Xilinx AXI Direct Memory Access Engine
Documentation: DT: vdma: update binding doc for AXI DMA
dmaengine: vdma: Rename xilinx_vdma_ prefix to xilinx_dma
dmaengine: slave means at least one of DMA_SLAVE, DMA_CYCLIC
dmaengine: mv_xor: Allow selecting mv_xor for mvebu only compatible SoC
...
Driver updates for ARM SoCs, these contain various things that touch
the drivers/ directory but got merged through arm-soc for practical
reasons. For the most part, this is now related to power management
controllers, which have not yet been abstracted into a separate
subsystem, and typically require some code in drivers/soc or arch/arm
to control the power domains.
Another large chunk here is a rework of the NVIDIA Tegra USB3.0
support, which was surprisingly tricky and took a long time to
get done.
Finally, reset controller handling as always gets merged through here
as well.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=x+iD
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Arnd Bergmann:
"Driver updates for ARM SoCs, these contain various things that touch
the drivers/ directory but got merged through arm-soc for practical
reasons.
For the most part, this is now related to power management
controllers, which have not yet been abstracted into a separate
subsystem, and typically require some code in drivers/soc or arch/arm
to control the power domains.
Another large chunk here is a rework of the NVIDIA Tegra USB3.0
support, which was surprisingly tricky and took a long time to get
done.
Finally, reset controller handling as always gets merged through here
as well"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (97 commits)
arm-ccn: Enable building as module
soc/tegra: pmc: Add generic PM domain support
usb: xhci: tegra: Add Tegra210 support
usb: xhci: Add NVIDIA Tegra XUSB controller driver
dt-bindings: usb: xhci-tegra: Add Tegra210 XUSB controller support
dt-bindings: usb: Add NVIDIA Tegra XUSB controller binding
PCI: tegra: Support per-lane PHYs
dt-bindings: pci: tegra: Update for per-lane PHYs
phy: tegra: Add Tegra210 support
phy: Add Tegra XUSB pad controller support
dt-bindings: phy: tegra-xusb-padctl: Add Tegra210 support
dt-bindings: phy: Add NVIDIA Tegra XUSB pad controller binding
phy: core: Allow children node to be overridden
clk: tegra: Add interface to enable hardware control of SATA/XUSB PLLs
drivers: firmware: psci: make two helper functions inline
soc: renesas: rcar-sysc: Add support for R-Car H3 power areas
soc: renesas: rcar-sysc: Add support for R-Car E2 power areas
soc: renesas: rcar-sysc: Add support for R-Car M2-N power areas
soc: renesas: rcar-sysc: Add support for R-Car M2-W power areas
soc: renesas: rcar-sysc: Add support for R-Car H2 power areas
...
These are all the updates to device tree files for 32-bit platforms,
which as usual makes up the bulk of the ARM SoC changes: 462 non-merge
changesets, 450 files changed, 23340 insertions, 5216 deletions.
The three platforms that are added with the "soc" branch are here as well,
and we add some related machine files:
- For Aspeed AST2400/AST2500, we get the evaluation platform and
the Tyan Palmetto POWER8 mainboard that uses the AST2400 BMC
- For Oxnas 810SE, the Western Digital "My Book World Edition"
is added as the only platform at the moment.
- For ARM MPS2, the AN385 (Cortex-M3) and AN399 (Cortex-M7)
are supported
On the ARM Realview development platform, we now support all machines
with device tree, previously only the board files were supported, which
in turn will likely be removed soon.
Qualcomm IPQ4019 is the second generation ARM based "Internet Processor",
following the IPQ806x that is used in many high-end WiFi routers. This one
integrates two ath10k wifi radios that were previously on separate chips.
Other boards that got added for existing chips are:
- On Ti OMAP family:
- Amazon Kindle Fire, first generation, tablet and ebook reader
- OnRISC Baltos iR 2110 and 3220 embedded industrial PCs
- TI AM5728 IDK, TI AM3359 ICE-V2, and TI DRA722 Rev C EVM
development systems
- On Samsung EXYNOS platform:
- Samsung ARTIK5 evaluation board, see
https://www.artik.io/modules/overview/artik-5/
- On NXP i.MX platforms:
- Ka-Ro electronics TX6S-8034, TX6S-8035, TX6U-8033, TX6U-81xx,
TX6Q-1036, TX6Q-1110/-1130, TXUL-0010 and TXUL-0011 industrial
SoM modules
- Embest MarS Board i.MX6Dual DIY platform
- Boundary Devices i.MX6 Quad Plus Nitrogen6_MAX and
SoloX Nitrogen6sx embedded boards
- Technexion Pico i.MX6UL compute module
- ZII VF610 Development Board
- On Marvell embedded (mvebu, orion, kirkwood) platforms:
- Linksys Viper (E4200v2 / EA4500) WiFi router
- Buffalo Kurobox Pro NAS
- On Qualcomm Snapdragon:
- Arrow DragonBoard 600c (96boards) with APQ8064 Snapdragon 600
- On Rockchips platform:
- mqmaker MiQi single-board computer
- On Altera SoCFPGA:
- samtec VIN|ING 1000 vehicle communication interface
- On Allwinner Sunxi platforms:
- Dserve DSRV9703C tablet
- Difrnce DIT4350 tablet
- Colorfly E708 Q1 tablet
- Polaroid MID2809PXE04 tablet
- Olimex A20 OLinuXino LIME2 single board computer
- Xunlong Orange Pi 2, Orange Pi One, and Orange Pi PC
single board computers
Across many platforms, bug fixes went in to address warnings that
dtc now emits with 'make dtbs W=1'. Further changes for device enablement
went into Ti OMAP, bcm283x (Raspberry Pi), bcm47xx (wifi router),
Ti Davinci, Samsung EXYNOS, Marvell mvebu/kirkwood/orion, NXP i.MX/Vybrid
NXP LPC18xx, NXP LPC32xx, Renesas shmobile/r-mobile/r-car, Rockchips
rk3xxx, ST Ux500, ST STi, Atmel AT91/SAMA5, Altera SoCFPGA, Allwinner
Sunxi, Sigma Designs Tango, NVIDIA Tegra, Socionext Uniphier and ARM
Versatile Express.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Nx46
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Arnd Bergmann:
"These are all the updates to device tree files for 32-bit platforms,
which as usual makes up the bulk of the ARM SoC changes: 462 non-merge
changesets, 450 files changed, 23340 insertions, 5216 deletions.
The three platforms that are added with the "soc" branch are here as
well, and we add some related machine files:
- For Aspeed AST2400/AST2500, we get the evaluation platform and the
Tyan Palmetto POWER8 mainboard that uses the AST2400 BMC
- For Oxnas 810SE, the Western Digital "My Book World Edition" is
added as the only platform at the moment.
- For ARM MPS2, the AN385 (Cortex-M3) and AN399 (Cortex-M7) are
supported
On the ARM Realview development platform, we now support all machines
with device tree, previously only the board files were supported,
which in turn will likely be removed soon.
Qualcomm IPQ4019 is the second generation ARM based "Internet
Processor", following the IPQ806x that is used in many high-end WiFi
routers. This one integrates two ath10k wifi radios that were
previously on separate chips.
Other boards that got added for existing chips are:
Ti OMAP family:
- Amazon Kindle Fire, first generation, tablet and ebook reader
- OnRISC Baltos iR 2110 and 3220 embedded industrial PCs
- TI AM5728 IDK, TI AM3359 ICE-V2, and TI DRA722 Rev C EVM
development systems
Samsung EXYNOS platform:
- Samsung ARTIK5 evaluation board, see
https://www.artik.io/modules/overview/artik-5/
NXP i.MX platforms:
- Ka-Ro electronics TX6S-8034, TX6S-8035, TX6U-8033, TX6U-81xx,
TX6Q-1036, TX6Q-1110/-1130, TXUL-0010 and TXUL-0011 industrial
SoM modules
- Embest MarS Board i.MX6Dual DIY platform
- Boundary Devices i.MX6 Quad Plus Nitrogen6_MAX and SoloX
Nitrogen6sx embedded boards
- Technexion Pico i.MX6UL compute module
- ZII VF610 Development Board
Marvell embedded (mvebu, orion, kirkwood) platforms:
- Linksys Viper (E4200v2 / EA4500) WiFi router
- Buffalo Kurobox Pro NAS
Qualcomm Snapdragon:
- Arrow DragonBoard 600c (96boards) with APQ8064 Snapdragon 600
Rockchips platform:
- mqmaker MiQi single-board computer
Altera SoCFPGA:
- samtec VIN|ING 1000 vehicle communication interface
Allwinner Sunxi platforms:
- Dserve DSRV9703C tablet
- Difrnce DIT4350 tablet
- Colorfly E708 Q1 tablet
- Polaroid MID2809PXE04 tablet
- Olimex A20 OLinuXino LIME2 single board computer
- Xunlong Orange Pi 2, Orange Pi One, and Orange Pi PC single board
computers
Across many platforms, bug fixes went in to address warnings that dtc
now emits with 'make dtbs W=1'. Further changes for device enablement
went into Ti OMAP, bcm283x (Raspberry Pi), bcm47xx (wifi router), Ti
Davinci, Samsung EXYNOS, Marvell mvebu/kirkwood/orion, NXP i.MX/Vybrid
NXP LPC18xx, NXP LPC32xx, Renesas shmobile/r-mobile/r-car, Rockchips
rk3xxx, ST Ux500, ST STi, Atmel AT91/SAMA5, Altera SoCFPGA, Allwinner
Sunxi, Sigma Designs Tango, NVIDIA Tegra, Socionext Uniphier and ARM
Versatile Express"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (458 commits)
ARM: dts: tango4: Import watchdog node
ARM: dts: tango4: Update cpus node for cpufreq
ARM: dts: tango4: Update DT to match clk driver
ARM: dts: tango4: Initial thermal support
arm/dst: Add Aspeed ast2500 device tree
arm/dts: Add Aspeed ast2400 device tree
ARM: sun7i: dt: Add pll3 and pll7 clocks
ARM: dts: sunxi: Add a olinuxino-lime2-emmc
ARM: dts: at91: sama5d4: add trng node
ARM: dts: at91: sama5d3: add trng node
ARM: dts: at91: sama5d2: add trng node
ARM: dts: at91: at91sam9g45 family: reduce the trng register map size
ARM: sun4i: dt: Add pll3 and pll7 clocks
ARM: sun5i: chip: Enable the TV Encoder
ARM: sun5i: r8: Add display blocks to the DTSI
ARM: sun5i: a13: Add display and TCON clocks
ARM: dts: ux500: configure the accelerometers open drain
ARM: mx5: dts: Enable USB OTG on M53EVK
ARM: dts: imx6ul-14x14-evk: Add audio support
ARM: dts: imx6qdl: Remove unneeded unit-addresses
...
Traditionally we've had two separate branches for cleanups and non-critical
bug fixes, but both of these got smaller with each release and the differences
are rather unclear now, so it seems more appropriate to have a combined
branch.
The most notably change is for OMAP, which gets a small rework to simplify
handling of the AUXDATA mechanism used on machines that are not completely
DT based yet, along with other work that is used as preparation for dropping
the legacy board files.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=au7y
-----END PGP SIGNATURE-----
Merge tag 'armsoc-cleanups-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups and fixes from Arnd Bergmann:
"Traditionally we've had two separate branches for cleanups and
non-critical bug fixes, but both of these got smaller with each
release and the differences are rather unclear now, so it seems more
appropriate to have a combined branch.
The most notable change is for OMAP, which gets a small rework to
simplify handling of the AUXDATA mechanism used on machines that are
not completely DT based yet, along with other work that is used as
preparation for dropping the legacy board files"
* tag 'armsoc-cleanups-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: dts: exynos: Add interrupt line to MAX8997 PMIC on exynos4210-trats
ARM: dts: exynos: Fix regulator name to avoid forbidden character on exynos4210-trats
ARM: dts: exynos: Add MFC memory banks for Peach boards
ARM: OMAP2+: n900 needs MMC slot names for legacy user space
ARM: OMAP2+: Add more functions to pwm pdata for ir-rx51
ARM: debug: remove extraneous DEBUG_HI3716_UART option
ARM: OMAP2+: Simplify auxdata by using the generic match
of/platform: Allow secondary compatible match in of_dev_lookup
ARM: davinci: use IRQCHIP_DECLARE for cp_intc
ARM: davinci: remove unused DA8XX_NUM_UARTS
ARM: davinci: simplify call to of populate
ARM: DaVinci USB: removed deprecated properties from MUSB config
ARM: rockchip: Fix use of plain integer as NULL pointer
ARM: realview: hide unused 'pmu_device' object
soc: versatile: dynamically detect RealView HBI numbers
Pull crypto update from Herbert Xu:
"API:
- Crypto self tests can now be disabled at boot/run time.
- Add async support to algif_aead.
Algorithms:
- A large number of fixes to MPI from Nicolai Stange.
- Performance improvement for HMAC DRBG.
Drivers:
- Use generic crypto engine in omap-des.
- Merge ppc4xx-rng and crypto4xx drivers.
- Fix lockups in sun4i-ss driver by disabling IRQs.
- Add DMA engine support to ccp.
- Reenable talitos hash algorithms.
- Add support for Hisilicon SoC RNG.
- Add basic crypto driver for the MXC SCC.
Others:
- Do not allocate crypto hash tfm in NORECLAIM context in ecryptfs"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (77 commits)
crypto: qat - change the adf_ctl_stop_devices to void
crypto: caam - fix caam_jr_alloc() ret code
crypto: vmx - comply with ABIs that specify vrsave as reserved.
crypto: testmgr - Add a flag allowing the self-tests to be disabled at runtime.
crypto: ccp - constify ccp_actions structure
crypto: marvell/cesa - Use dma_pool_zalloc
crypto: qat - make adf_vf_isr.c dependant on IOV config
crypto: qat - Fix typo in comments
lib: asn1_decoder - add MODULE_LICENSE("GPL")
crypto: omap-sham - Use dma_request_chan() for requesting DMA channel
crypto: omap-des - Use dma_request_chan() for requesting DMA channel
crypto: omap-aes - Use dma_request_chan() for requesting DMA channel
crypto: omap-des - Integrate with the crypto engine framework
crypto: s5p-sss - fix incorrect usage of scatterlists api
crypto: s5p-sss - Fix missed interrupts when working with 8 kB blocks
crypto: s5p-sss - Use common BIT macro
crypto: mxc-scc - fix unwinding in mxc_scc_crypto_register()
crypto: mxc-scc - signedness bugs in mxc_scc_ablkcipher_req_init()
crypto: talitos - fix ahash algorithms registration
crypto: ccp - Ensure all dependencies are specified
...
- fix a regression on the clock subsystem while switching to syscon/regmap
due to a stricter check of the register map.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJXM0NyAAoJEAf03oE53VmQ0IwIAI05Acjbko78+Hm/kWHlbJrx
5BLpJqTGLavbjbPjFnElKTr1c8m7Bgd6HNcat/2z9ZNh8/82FXyGOjYSp4W0BE9V
ovyD/lz/2fZyom4YLJjdCnVkwIV1pKHS+uNxy5zXMY2gJfz4VRtUh54H3ArdaQOE
LOKvrVl9bGorLbzbTpH0rSeKqQ1XFGPDlp1A3GUtI6646RWd5Eqe6zDzgQUwWJis
AR+sAcsqVb+IWY5rZwMyL0oZ1kjnEw4tihDTy+G+eBXRdRMYqSgEt8dBz65T3VYi
5EFXLuLjknnf3qVaxEU+og6kiJkefTYdB4I7xVR+dKbcILBSSqdHxlG1HmNkBQ4=
=CF/9
-----END PGP SIGNATURE-----
Merge tag 'at91-fixes2' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91 into fixes
Merge "Second AT91 fix PR for 4.6" from Nicolas Ferre:
- fix a regression on the clock subsystem while switching to syscon/regmap
due to a stricter check of the register map.
* tag 'at91-fixes2' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91:
ARM: dts: at91: sam9x5: Fix the memory range assigned to the PMC
The memory range assigned to the PMC (Power Management Controller) was
not including the PMC_PCR register which are used to control peripheral
clocks.
This was working fine thanks to the page granularity of ioremap(), but
started to fail when we switched to syscon/regmap, because regmap is
making sure that all accesses are falling into the reserved range.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reported-by: Richard Genoud <richard.genoud@gmail.com>
Tested-by: Richard Genoud <richard.genoud@gmail.com>
Fixes: 863a81c3be ("clk: at91: make use of syscon to share PMC registers in several drivers")
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
v4.7:
1. Add bus nodes for Exynos3250, Exynos4x12, Exynos4210 and Exynos542x.
2. Split out common PPMU (Performance Monitoring Unit) nodes into separate
DTSI. The PPMU provides performance data for devfreq.
3. Add NoCP (Network on Chip Probe) node for Exynos542x. On this SoC, like PPMU
on older designs, provides performance data for devfreq.
4. Enable DFVS (Dynamic Voltage and Frequency Scaling) on boards:
- Exynos3250 Rinato,
- Exynos4412 Odroid-X/X2/U3 and Trats2,
- Exynos5422 Odroid XU3/XU3-Lite/XU4.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJXKfGRAAoJEME3ZuaGi4PXY/MQAJAjXSYPc2lj53BcFhZVVuel
J+zITvarTDdV/CF01SMyYA760OEVYE7eZ59kQpkyiEy018/Wle63ortKco0UQprW
JLRcYUPjvtByCmhgX8yvboYiS0Q5xLLVi9mMg802tR3ccxnJcZmZRPIwBRTmn7Nr
P/WpSoEM3E5yZzqTu1AuvmqW7fys1kCDTPcaFH3OZNnEz+r/6KAgzhip95ihIKq0
DT7dFPFI2F90p+ozcS8O8G/LLFwyOjPfVi0G2hOPmo8mvvizorLiHU2P78EgG+L5
UyXrXHWvgaUtc5kiE+naH6ihNQuz1hSW4IfIzvLTls1n0e0Sz4O130h96e0XgMSa
c0kmHk0rFC8LNqeO4Ly+ojPHiXCUU+8DMF0RNMXMJdnH+jGlbzkzNnUB7csaH4xz
wVD0gSBBl/ydm+iFJ6r89zLVYN8mX3MXBNUBfarnZe+h2i2Fb/RmO6l8VWVVh2dP
576LLCqTOx0BdhIIqeK3Wv4edBiyIPTQUjadksat6XwEfg7WtNTIv2Zg7As3uXYc
hjRhxQ6rj48NBjxz5NT/OV9uHuKWoMaJ/x222UbtUTXV0hRufae9sb1dne8kuYag
hYChIYHu3t3DR5EIrAEEp1vHUglf9luUyDg01o7Fq63JK2D/NruAeWSm/PmCvI03
1Xh2eAVmNePpmL+qpRcT
=pAOJ
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-devfreq-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/late
Merge "ARM: dts: exynos: Devfreq for v4.7: from Krzysztof Kozłowski:
Topic branch for Device Tree changes adding new generic devfreq driver, for
v4.7:
1. Add bus nodes for Exynos3250, Exynos4x12, Exynos4210 and Exynos542x.
2. Split out common PPMU (Performance Monitoring Unit) nodes into separate
DTSI. The PPMU provides performance data for devfreq.
3. Add NoCP (Network on Chip Probe) node for Exynos542x. On this SoC, like PPMU
on older designs, provides performance data for devfreq.
4. Enable DFVS (Dynamic Voltage and Frequency Scaling) on boards:
- Exynos3250 Rinato,
- Exynos4412 Odroid-X/X2/U3 and Trats2,
- Exynos5422 Odroid XU3/XU3-Lite/XU4.
* tag 'samsung-dt-devfreq-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: Add support of Bus frequency using VDD_INT for exynos5422-odroidxu3
ARM: dts: exynos: Add bus nodes using VDD_INT for Exynos542x SoC
ARM: dts: exynos: Add NoC Probe dt node for Exynos542x SoC
ARM: dts: exynos: Add support of bus frequency for exynos4412-trats/odroidu3
ARM: dts: exynos: Expand the voltage range of buck1/3 regulator for exynos4412-odroidu3
ARM: dts: exynos: Add support of bus frequency using VDD_INT for exynos3250-rinato
ARM: dts: exynos: Add exynos4412-ppmu-common dtsi to delete duplicate PPMU nodes
ARM: dts: exynos: Add bus nodes using VDD_MIF for Exynos4210
ARM: dts: exynos: Add bus nodes using VDD_INT for Exynos4x12
ARM: dts: exynos: Add bus nodes using VDD_MIF for Exynos4x12
ARM: dts: exynos: Add bus nodes using VDD_INT for Exynos3250
ARM: dts: exynos: Add DMC bus frequency for exynos3250-rinato/monk
ARM: dts: exynos: Add DMC bus node for Exynos3250
clk: samsung: exynos542x: Add the clock id for ACLK
dt-bindings: clock: Add the clock id for ACLK clock of Exynos542x SoC
- Add LCDIF and FlexCAN device support for i.MX7D
- New support i.MX7D based Nitrogen7 board from Boundary Devices
- Add display support for vf610-colibri board
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXKLuLAAoJEFBXWFqHsHzOZ88IAKb4kS4KN0fOdNLMyE7wwi9Y
JAfKZEaOASwifm8LZBvC5F3DrLvmxykbbhNiIOFlr0var+wK15HDJNgbTbWDtcUU
vS4Jag5UrMXdd7wW/S7Lik2TeEKylt1P3asrrvxvVLkQM7xKeixS3n0LpqzX+RQ1
rOdPv8aSFewX2C7EaMoXPwoJGNXYvA+cge6pIdpO+EHpTiK3PDkEE9C3Vv34I8R7
XQxlKbqoXBxcYXBWseyq57QKQVsnRcvIPTU4HSMJAqJxiMPbgR6KIVAupzjDmtKM
aVyXoZTayFhBrdC8l7o3YwOjqHD9Rov7rgEmS2a9qIrkiqxBz/TjsfpBQT23+X0=
=t+hk
-----END PGP SIGNATURE-----
Merge tag 'imx-dt-clkdep-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/late
Merge "The i.MX device tree updates with new clocks for 4.7" from Shawn Guo:
- Add LCDIF and FlexCAN device support for i.MX7D
- New support i.MX7D based Nitrogen7 board from Boundary Devices
- Add display support for vf610-colibri board
* tag 'imx-dt-clkdep-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: vf610-colibri: enable display controller
ARM: dts: vf610: add display nodes
ARM: dts: imx: add Boundary Devices Nitrogen7 board
ARM: dts: imx7d: add flexcan support
ARM: dts: imx7d: add lcdif support
clk: imx: vf610: fix whitespace in vf610-clock.h
clk: imx: vf610: add TCON ipg clock
clk: imx: vf610: fix DCU clock tree
clk: imx: add ckil clock for i.MX7
clk: imx: vf610: add suspend/resume support
clk: imx: vf610: add WKPU unit
clk: imx: vf610: leave DDR clock on
clk: imx: clk-gate2: allow custom gate configuration
clk: imx6sx: Register SAI clocks as shared clocks
The device driver was added in v4.5 by commit dca536c433
("watchdog: add support for Sigma Designs SMP86xx/SMP87xx")
Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This platform will use the new generic platdev driver.
Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Commit fefe0535b7 ("clk: tango4: improve clkgen driver") added
support for USB and SDIO clocks.
Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Define the CPU temperature sensor, and critical trip point.
Commit 799d71da471c ("add temperature sensor support for tango SoC")
added the device driver.
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Mostly DT patches to enable the new DRM driver on the CHIP, preliminary
support for the A10 and A20, and a support for a new variant of the Olimex
A20-Olinuxino-Lime2 featuring an eMMC
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=zrar
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt-for-4.7-2' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into next/dt
Merge "Allwinner DT changes for 4.7, round 2" from Maxime Ripard:
Mostly DT patches to enable the new DRM driver on the CHIP, preliminary
support for the A10 and A20, and a support for a new variant of the Olimex
A20-Olinuxino-Lime2 featuring an eMMC
* tag 'sunxi-dt-for-4.7-2' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
ARM: sun7i: dt: Add pll3 and pll7 clocks
ARM: dts: sunxi: Add a olinuxino-lime2-emmc
ARM: sun4i: dt: Add pll3 and pll7 clocks
ARM: sun5i: chip: Enable the TV Encoder
ARM: sun5i: r8: Add display blocks to the DTSI
ARM: sun5i: a13: Add display and TCON clocks
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ED1J
-----END PGP SIGNATURE-----
Merge tag 'aspeed-for-4.7-dts' of https://github.com/shenki/linux into next/dt
Merge "aspeed devicetree for 4.7" from Joel Stanley:
This device trees for a pair of Aspeed BMC SoCs and the boards that
they sit in.
* tag 'aspeed-for-4.7-dts' of https://github.com/shenki/linux:
arm/dst: Add Aspeed ast2500 device tree
arm/dts: Add Aspeed ast2400 device tree
doc/devicetree: Add Aspeed and Tyan to vendor-prefixes
- a fix for the VInCo platform: reset gpio specification for Ethernet
- addition of True Random Number Generator (TRNG) for all sama5 platforms
- trivial adjustment of TRNG register map size for at91sam9g45 family
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJXLK+JAAoJEAf03oE53VmQlDEIAJXbOrw/dKJzFxdvzqhMszC+
2IKkolGCsYposwryyNjzYkGaSZaWPRo/1TWUiOV7NkyRRACo4VN+ksPphbIQU5qg
5N5G6VGHzuGC9jJXVAV1W9aNGx0vDYd6A4SuTOOyxxy9S8lpVYXUbthaf6MWrOUB
QqMpbDtCt/g5t7RYajWYZGDARAU92UT97FQxAHGX642Ytrcvp8ITVCrL6rh6vKPE
f91okoe9fipqnp87EvgxcQITxtQUJnQcGXRluzz8m3uvQMEvQk9uxcGaJfM+TECT
G0X6yNmFLIPsxxkZxxKVMg54b5pxi9SthohFoY4GKv3JRlSJDzuHmdIqnjwIL/s=
=iZ40
-----END PGP SIGNATURE-----
Merge tag 'at91-dt3' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91 into next/dt
Merge "Third batch of DT changes for 4.7" from Nicolas Ferre:
- a fix for the VInCo platform: reset gpio specification for Ethernet
- addition of True Random Number Generator (TRNG) for all sama5 platforms
- trivial adjustment of TRNG register map size for at91sam9g45 family
* tag 'at91-dt3' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91:
ARM: dts: at91: sama5d4: add trng node
ARM: dts: at91: sama5d3: add trng node
ARM: dts: at91: sama5d2: add trng node
ARM: dts: at91: at91sam9g45 family: reduce the trng register map size
ARM: dts: at91: VInCo: fix phy reset gpio flag
Fabio Estevam