clk_get() on a disabled clock node will return -EPROBE_DEFER, which can
cause drivers to be deferred forever if such clocks are referenced in
their devices' clocks properties.
Update the various disabled external clock nodes to default to a
frequency of 0, but don't disable them, to prevent this.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
clk_get() on a disabled clock node will return -EPROBE_DEFER, which can
cause drivers to be deferred forever if such clocks are referenced in
their devices' clocks properties.
Update the various disabled external clock nodes to default to a
frequency of 0, but don't disable them, to prevent this.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
clk_get() on a disabled clock node will return -EPROBE_DEFER, which can
cause drivers to be deferred forever if such clocks are referenced in
their devices' clocks properties.
Update the various disabled external clock nodes to default to a
frequency of 0, but don't disable them, to prevent this.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Introduce am335x-baltos.dtsi, that provides common configuration
for the whole device family based on the same SODIMM module.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
According to Data Manual(SPRS915P) of AM57x, TI QSPI controller on
DRA74(rev 1.1+)/DRA72 EVM can support up to 64MHz in MODE-0, whereas
MODE-3 is limited to 48MHz. Hence, switch to MODE-0 for better
throughput.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
DRA7 family of processors from Texas Instruments, have a hardware module
called IODELAYCONFIG Module which is expected to be configured. This
block allows very specific custom fine tuning for electrical
characteristics of IO pins that are necessary for functionality and
device lifetime requirements. IODelay module has it's own register space
with registers to configure various pins.
According to AM572x TRM SPRUHZ6E October 2014–Revised January 2016[1]
section 18.4.6.1 Pad Configuration, in addition to pinmuxing(MUXMODE),
when operating a pad in certain mode, Virtual/Manual IO Timing Mode must
also be configured to ensure that IO timings are met (DELAYMODE and
MODESELECT fields of pad's IODELAYCONFIG module register). According to
section 18.4.6.1.7 Isolation Requirements of above TRM, when
reprogramming MUXMODE, DELAYMODE, and MODESELECT fields, there is a
potential for a significant glitch on the corresponding IO. It is hence
recommended to do this with I/O isolation (which can only be done in
initial stages of bootloader). QSPI is one such module that requires
IODELAY configuration. So, this patch removes the pinmux for
QSPI for DRA74/DRA72 EVM as it needs to be done in bootloader (U-Boot)
and cannot be done in kernel.
Users should migrate to U-Boot v2016.05-rc1 or higher.
[1] http://www.ti.com/lit/ug/spruhz6e/spruhz6e.pdf
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Without that, regulators are left in the mode last set by the bootloader or
by the kernel the device was rebooted from. This leads to various problems,
like non-working peripherals.
Signed-off-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Reviewed-By: Sebastian Reichel <sre@kernel.org>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
According to the TRM, SCM CONTROL_CSIRXFE register is on offset 0x6c
Signed-off-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Reviewed-By: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The boards use a TI variant of the PCF8575 so specify that
in the compatible string.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
As per the data sheet starting from SPRUHQ0H (Nov 2015 - Latest[1]),
VDD_CORE can vary from 0.85v to 1.15v for AVS class0. VDD GPU/DSP
et.al. can range from 0.85v to 1.25V with AVS class0
Since dynamic voltage scaling is disabled for DRA7/AM57xx SoCs for
all SoC rails other than MPU, the bootloader is responsible for
setting up the AVS class0 voltage, however, with wrong voltage machine
constraints in dtb, regulator framework will lower the voltage below
the required voltage levels for certain samples in production flow.
This can cause catastrophic failures which can be pretty hard to
identify.
Update board files which don't match required specification.
[1] http://www.ti.com/product/AM5728/datasheet/specifications#SPRT637-7340
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
ldo4_reg is connected to DSS, and should always be 1.8V. However the The
dts defines a range of 1.5V-1.8V, which requires somethings to set the
actual voltage at runtime. Currently we set the voltage in omapdss
driver.
As the voltage must always be 1.8V, let's just define the range to 1.8V
so that the driver doesn't need to deal with the voltage. In fact, the
driver should not touch the voltage, except in the cases where the
voltage needs to be changed at runtime.
I presume the situation is the same for ldo1_reg, used for CSI, although
I think it is not currently used in the mainline.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
ldo4_reg is connected to DSS, and should always be 1.8V. However the
The dts defines a range of 1.5V-1.8V, which requires somethings to set
the actual voltage at runtime. Currently we set the voltage in omapdss
driver.
As the voltage must always be 1.8V, let's just define the range to 1.8V
so that the driver doesn't need to deal with the voltage. In fact, the
driver should not touch the voltage, except in the cases where the
voltage needs to be changed at runtime.
I presume the situation is the same for ldo1_reg, used for CSI, although
I think it is not currently used in the mainline.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Doing so saves quite a bit of code in the driver.
For more information on the 'reserved-memory' bindings see:
Documentation/devicetree/bindings/reserved-memory/reserved-memory.txt
Suggested-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
This patch supplies the Mailbox Controller nodes. In order to
request channels, these nodes will be referenced by Mailbox
Client nodes.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
You'll notice that the voltage cell is populated with 0's. Voltage
information is very platform specific, even depends on 'cut' and
'substrate' versions. Thus it is left blank for a generic (safe)
implementation. If other nodes/properties are provided by the
bootloader, the ST CPUFreq driver will over-ride these generic
values.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
When compiled with "W=1", dtc complains: e.g.
"Warning (unit_address_vs_reg):
Node /soc/ipu@02800000/port@2/endpoint@0
has a unit name, but no reg property"
Endpoint nodes don't have a reg property, and the addresses
in their node names are ordinals without any special meaning
so remove them and swap them for semantic node names.
Signed-off-by: Joshua Clayton <stillcompiling@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Table 8 from MX6DL datasheet (IMX6SDLCEC Rev. 5, 06/2015):
http://cache.nxp.com/files/32bit/doc/data_sheet/IMX6SDLCEC.pdf
states the following:
"LDO Output Set Point (VDD_ARM_CAP) = 1.125 V minimum for operation
up to 396 MHz."
So fix the entry by adding the 25mV margin value as done in the other
entries of the table, which results in 1.15V for 396MHz operation.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
198MHz is a valid operating point for mx6sx.
Add entries for VDD_ARM_CAP and VDD_SOC_CAP voltages for 198MHz according
to the imx6sx datahseet:
http://cache.nxp.com/files/32bit/doc/data_sheet/IMX6SXIEC.pdf
(a 25mV offset is added to the minimum allowed values for safety).
These values also match the ones from the NXP kernel.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Adjust the VDD_ARM_CAP and VDD_SOC_CAP voltages according to
Table-11 from MX6UL datasheet:
http://cache.nxp.com/files/32bit/doc/data_sheet/IMX6ULCEC.pdf
(a 25mV offset is added to the minimum allowed values for safety).
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Application Notes 399 and 400 shares the same memory map and
features. Both are shipped with Cortex-M7 and have the same peripheral
as AN385/AN386, but with different location of PSRAM and Ethernet
controller.
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Application Notes 385 and 386 shares the same memory map and features
except the CPU is used. AN385 is supplied with Cortex-M3 CPU and AN386
is supplied with Cortex-M4.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
* Correct preset_lpj calculation which may lead to too short delays
* Correct handling of optional clocks on r8a7791 to restore
access to the serial port the porter board
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJXGEtmAAoJENfPZGlqN0++aYIP/RCANWvI9Z7VH/Y/NQ1f5t4Y
l4Uv1/dSuIHJq44z0sLMD5gmDVKqP1NnCncfkZabDXceGm9Fk3DlFxeLd+ahMN+B
dBtDpf1AA9Mr1AEoBrXjNimWSupvJalatqk3nWfLnjpGHQJOKTZCekikQb9WBA5t
l5r5Pvu/leRfyg/wi10F3hq0a2drKbIbFDOzh37L7al9cvZTnyVZNcchb/vlqZmt
kAi90crLUXvQ9eOw357kFBmigQF5r/fD0X3f5sFYyDlNldZg3chkyghiluiOcXDL
eEc6TdHNT/a9hixqpW/Z1BinpvFF+vIjfUZBW9wXTRz0t9EX5Pxr9wSXWEY4+hmp
DrI9eiEAbX8ltfjOo3Q7LgHstjZ6AJyk3CZJBWk8i2DLK5SEt6eum/BvKRmakTa+
DLe+SES+uUfg1d35WEqhqPeO7JEybPAVyto++NrCRSkPeDeO32+h2O6yEsMBqEKC
HFoV/V86Ufqq8MCiZkQBZJGNYqcTeKMiXzvte23tcAXXYmxMct5Z4HLCiFEM4paw
yyThG9VZofe4pt03u9XqiZjEu23AopMpM9xDpUjK3CKYq6uaJxNoJcgJC6TBbkmT
D7kdmhhlWCLeyr3pqblbqiWdK7Bx9B65aFhm/nilX0y4p3vvT46vMLvG4SgfFojv
Ybr9ICHZMaTxJ1V32fty
=k7qU
-----END PGP SIGNATURE-----
Merge tag 'renesas-fixes-for-v4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Renesas ARM Based SoC Fixes for v4.6
* Correct preset_lpj calculation which may lead to too short delays
* Correct handling of optional clocks on r8a7791 to restore
access to the serial port the porter board
This is a backmerge of v4.6 fixes, to avoid a merge conflict between 4.6
and our next/dt branch.
* tag 'renesas-fixes-for-v4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: timer: Fix preset_lpj leading to too short delays
Revert "ARM: dts: porter: Enable SCIF_CLK frequency and pins"
ARM: dts: r8a7791: Don't disable referenced optional clocks
Fix a typo on PIN_PD24 for UTXD2 and FLEXCOM4_IO3 which were
wrongly linked to PIN_PD23).
Signed-off-by: Florian Vallee <fvallee@eukrea.fr>
Fixes: 7f16cb676c ("ARM: at91/dt: add sama5d2 pinmux")
Cc: stable@vger.kernel.org # v4.4+
[nicolas.ferre@atmel.com: add commit message, changed subject]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Add Western Digital My Book World Edition device tree based on
Oxford Semiconductor OX810SE SoC.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The BA16 module has a PMIC that uses the WDOG_B output from iMX6 to
reset the system on a watchdog timeout. Configure the watchdog to assert
the external reset signal (WDOG_B) using fsl,ext-reset-output property.
Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Previously the LDB_DIx clocks could be specified in the ldb node. With
the ERR009219 errata fix applied, the ldb_di clocks now needs to be
specified in the clks node to ensure the clocks are setup early in the
boot process.
Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The default monitor that ships with B850v3 requires a 65MHz pixel clock.
65MHz can not be achieved using PLL3 (480MHz/7=68.5MHz). Hence set the
LDB_DIx clock source to PLL5. Since PLL5 is already in use by IPU1_DIx,
set the clock source for IPU1_DIx to PLL2_PFD2 to allow simultaneous
display on both LVDS and HDMI interface.
Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Remove ldb panel entry for the following reasons:
- The b850v3 has an onboard LVDS to DisplayPort converter (STDP4028). So
we should not limit the monitors that can be connected by hardcoding the
auo,b133htn01 1080p panel.
- The default resolution on the LVDS interface needs to be WXGA or less.
Otherwise when a 1080p monitor is connected to the HDMI port there is no
output on both the LVDS and HDMI ports since a single IPU on i.MX6 can
not handle two 1080p displays. With the panel entry removed from the
devicetree, drm driver defaults the resolution on LVDS interface to XGA.
Once in userspace, applications can set the desired resolution on LVDS
interface over IPU2 CRTC.
Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
to the clk-ti branch from the Linux clk tree for the ADPLL clock driver.
Otherwise things won't keep booting properly when we flip over to use
the clock driver instead of fixed clocks set up by the bootloader.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=2Lew
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.6/dt-ti81xx-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Enable dm814x and dra62x clock driver. This branch has a dependency
to the clk-ti branch from the Linux clk tree for the ADPLL clock driver.
Otherwise things won't keep booting properly when we flip over to use
the clock driver instead of fixed clocks set up by the bootloader.
* tag 'omap-for-v4.6/dt-ti81xx-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Add clocks for dm814x ADPLL
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
1. Support for external expansion bus useful for additional hardware
e.g. LogicTile Express daughterboards (Brian Starkey)
2. Fix for device node name unit-address presence/absence warnings
enabled in recently update DTC (Sudeep Holla)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=CN/A
-----END PGP SIGNATURE-----
Merge tag 'vexpress-for-v4.7/updates' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into next/dt
Merge "ARMv7 Vexpress updates/fixes for v4.7" from Sudeep Holla:
1. Support for external expansion bus useful for additional hardware
e.g. LogicTile Express daughterboards (Brian Starkey)
2. Fix for device node name unit-address presence/absence warnings
enabled in recently update DTC (Sudeep Holla)
* tag 'vexpress-for-v4.7/updates' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
ARM: dts: vexpress: Add external expansion bus to DT
ARM: dts: vexpress: fix node name unit-address presence warnings
* Configure NMI key as wakeup source in DT of kzm9g board
* Add SDHI support to DT of gose board
* Add support of UHS-I SDR-50 for SDHI to DT of r8a7790 SoC
* Correct interrupt type for ARM TWD in DT of r8a7779 and sh73a0 SoCs
* Add IIC support to DT of r8a7794 SoC
* Add CAN support to DT of r8a7793 and r8a7794 SoCs
* Add SCIF2 support to r8a7790 device tree
* Use CAN, JPU and USB3.0 fallback compatibility string
in DT of r8a7791 and r8a7790 SoCs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=vStA
-----END PGP SIGNATURE-----
Merge tag 'renesas-dt-for-v4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Merge "Renesas ARM Based SoC DT Updates for v4.7" from Simon Horman:
* Configure NMI key as wakeup source in DT of kzm9g board
* Add SDHI support to DT of gose board
* Add support of UHS-I SDR-50 for SDHI to DT of r8a7790 SoC
* Correct interrupt type for ARM TWD in DT of r8a7779 and sh73a0 SoCs
* Add IIC support to DT of r8a7794 SoC
* Add CAN support to DT of r8a7793 and r8a7794 SoCs
* Add SCIF2 support to r8a7790 device tree
* Use CAN, JPU and USB3.0 fallback compatibility string
in DT of r8a7791 and r8a7790 SoCs
* tag 'renesas-dt-for-v4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (22 commits)
ARM: dts: gose: Enable SDHI controllers
ARM: dts: r8a7793: Add SDHI controllers
ARM: dts: r8a7790: fix max-frequency for SDHI
ARM: dts: kzm9g: Configure NMI key as wake-up source
ARM: dts: r8a7790: lager: Enable UHS-I SDR-50
ARM: dts: r8a7790: Set maximum frequencies for SDHI clocks
ARM: dts: r8a7791: Use USB3.0 fallback compatibility string
ARM: dts: r8a7790: Use USB3.0 fallback compatibility string
ARM: dts: r8a7779: Correct interrupt type for ARM TWD
ARM: dts: sh73a0: Correct interrupt type for ARM TWD
ARM: dts: r8a7794: Add IIC nodes
ARM: dts: r8a7794: add IIC clocks
ARM: dts: r8a7793: add CAN nodes to device tree
ARM: dts: r8a7793: add CAN clocks to device tree
ARM: dts: r8a7794: add CAN nodes to device tree
ARM: dts: r8a7794: add CAN clocks to device tree
ARM: dts: r8a7790: use fallback can compatibility string
ARM: dts: r8a7791: use fallback can compatibility string
ARM: dts: r8a7790: Add SCIF2 device node
ARM: dts: r8a7790: Add SCIF2 clock
...
to the clk-ti branch from the Linux clk tree for the ADPLL clock driver.
Otherwise things won't keep booting properly when we flip over to use
the clock driver instead of fixed clocks set up by the bootloader.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=2Lew
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.6/dt-ti81xx-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Enable dm814x and dra62x clock driver. This branch has a dependency
to the clk-ti branch from the Linux clk tree for the ADPLL clock driver.
Otherwise things won't keep booting properly when we flip over to use
the clock driver instead of fixed clocks set up by the bootloader.
* tag 'omap-for-v4.6/dt-ti81xx-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Add clocks for dm814x ADPLL
Fix off by one error in da850 device tree in
the number of INTC interrupts.
Signed-off-by: David Lechner <david@lechnology.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
[nsekhar@ti.com: commit message update]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Disable mdio and eth0 in da850.dtsi file. All other
devices are disabled by default and not all boards
will use these devices, so these should be disabled too.
da850-evm.dtb already had status = "okay" for these devices.
da850-enbw-cmc.dts did not, so they were added.
Signed-off-by: David Lechner <david@lechnology.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
[nsekhar@ti.com: commit description updates]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
The VExpress development platform has an external expansion bus which
can be used for additional hardware (e.g. LogicTile Express daughter
boards).
Add this bus to the VExpress CoreTile device-trees.The bus is described
for a CoreTile occupying site 1.
Acked-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Brian Starkey <brian.starkey@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Commit b993734718 ("scripts/dtc: Update to upstream version 53bf130b1cdd")
added warnings on node name unit-address presence/absence mismatch in
the device trees.
This patch fixes those warning on all the vexpress platforms where
unit-address is present in node name while the reg/ranges property is
not present.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Enable the S/PDIF transmitter present on the Cubietruck.
Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
In order to be standard to manage for rockchip SoCs, move the thermal
data into rk3288 dtsi, we needn't to add a new file for thermal.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Includes regulator and pin assignments.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The wrong values come from an old datasheet (H2 v0.6). Anything later
has the fixed value of 195MHz (H2 v0.7 up to Gen2-common V2.0).
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a GPIO key with wake-up capability for the NMI button.
This allows to wake up the system from s2ram without relying on the
buttons on the optional switch board.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the "1v8" pinctrl state and sd-uhs-sdr50 property to SDHI{0,2}.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The clock binding for the main clock controller was changed to an
indexed controller style binding on request of the clk
maintainers. This updates the dtsi to use the new bindings.
Signed-off-by: Lars Persson <larper@axis.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* Add DB600C support
* Add IPQ4019 support
* Add additional nodes for APQ8064
* Fix APQ8064 pinctrls for i2c/spi
* Add MSM8974 nodes for smp2p and smd
* Modify MSM8974 memory reserve for rfsa and rmtfs
* Add support for BQ27541 on Nexus7
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJXF+EAAAoJEFKiBbHx2RXV6/8P/jUWHwhQmd8NYvz/JVRjf+dP
hpwOkx66OwXwgtIrPkvu6edUjd6p6ll7tdwo14PsIjH5wCpSweXlqM/j93ucV0y5
MhulwfbeGFsMCMjV+4/IeQd7C7dHwu1WFvxoJux+GHhd12cKM67s6/EPJmyc+sUG
DET11PhwSi12KX1qoPkILNXs2Gtj4PCsqEYZ0gc1Q2vAlfqmNTOKgA7wBGWYby6Z
6fWrF0sBPEc/G2C4aAia+8Uq/Fh9s8CeGSX2oO6F/iRAag7SKR1j9bUl+/FNK5fR
6H0kVvmzrrKTnoCoftygy5brSm3OwU1SM3MpTc/QWC8AeHMk4fTItpDSrz4xyeTb
4+GzU1GWlnE0N3rnJFhPPDbybgJCJ9PrACoFDqIN4mLIyOFeWoT59vXmcJBOYZpJ
7XMLpooH3WX79vblvZne54BRLTo0LXrxr+FqtUeEljguK5nKKclNI6fijjnV3dU7
9dTd/xtW0YMta3uU/En+TSLzXXC3Sbx5MXKVhvcvClyhTNG2I3vY2mz7FuXUZpuY
CAuvjYJdZxEmv8z649TTBG4pQ1oPzp6H/kVlywSIH+Bn0vw1Pn+eImp4cE4TVAuv
YRaxjceYXTPSsVOdYVrztm4xM0NbZ91i0LiJrgxS0mvOJEmt/JkBF8/mUKWdI8SC
D/lrNzp0b6QIJ7KU9Vln
=C5LP
-----END PGP SIGNATURE-----
Merge tag 'qcom-dt-for-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux into next/dt
Merge "Qualcomm Device Tree Changes for v4.7" from Andy Gross:
* Add DB600C support
* Add IPQ4019 support
* Add additional nodes for APQ8064
* Fix APQ8064 pinctrls for i2c/spi
* Add MSM8974 nodes for smp2p and smd
* Modify MSM8974 memory reserve for rfsa and rmtfs
* Add support for BQ27541 on Nexus7
* tag 'qcom-dt-for-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux: (30 commits)
device-tree: nexus7: Add bq27541 battery interface to dts
ARM: dts: db600c: add support to magnetometer
ARM: dts: db600c: add spi support
ARM: dts: db600c: add i2c support
ARM: dts: db600c: Add on board leds support
ARM: dts: db600c: add on board sata support.
ARM: dts: db600c: add pcie support
ARM: dts: db600c: add usb support
ARM: dts: db600c: Add eMMC and SD card support
ARM: dts: db600c: add pmic regulator supplies
ARM: dts: db600c: add board support with serial
ARM: dts: apq8064: add gsbi7 i2c support
ARM: dts: apq8064: add support to gsbi1 uart
ARM: dts: apq8064: fix the pinctrls for i2c and spi
ARM: dts: qcom: apq8064: Add smd node and all edges
ARM: dts: qcom: apq8064: Add complete smsm node
ARM: dts: qcom: apq8064: Add syscon for sic-non-secure
ARM: dts: msm8974: Add modem smp2p and smd nodes
ARM: dts: msm8974: Add node for second i2c from blsp1
ARM: dts: msm8974: Split efs in rfsa and rmtfs
...
- Rafal adds proper VCC GPIO to be fed to the USB host controllers for known
BCM5301x devices needing that, he also enables earlycon, and enables the
SPI-NOR flashes on relevant devices
- Eric adds the VideoCore 4 Device Tree nodes to the BCM283x Device Tree and
provides a DRM patch to kick out the simplefb framebuffer to avoid conflicts
- Stephan adds proper CPU nodes for the ARM processor on the BCM2835 SoC Device
Tree
- Martin provides a binding fix for the DMA channel interrupt numbers and
description
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=UhGj
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-4.7/devicetree' of http://github.com/Broadcom/stblinux into next/dt
Merge "Broadcom ARM-based SoC Device Tree changes" from Florian Fainelli:
- Rafal adds proper VCC GPIO to be fed to the USB host controllers for known
BCM5301x devices needing that, he also enables earlycon, and enables the
SPI-NOR flashes on relevant devices
- Eric adds the VideoCore 4 Device Tree nodes to the BCM283x Device Tree and
provides a DRM patch to kick out the simplefb framebuffer to avoid conflicts
- Stephan adds proper CPU nodes for the ARM processor on the BCM2835 SoC Device
Tree
- Martin provides a binding fix for the DMA channel interrupt numbers and
description
* tag 'arm-soc/for-4.7/devicetree' of http://github.com/Broadcom/stblinux:
ARM: BCM5301X: Add DT entry for SPI controller and NOR flash
dt/bindings: bcm2835: correct description for DMA-int
ARM: bcm2835: add CPU node for ARM core
ARM: bcm2835: Add VC4 to the device tree.
drm/vc4: Kick out the simplefb framebuffer before we set up KMS.
ARM: BCM5301X: Enable earlycon on tested devices
ARM: BCM5301X: Set vcc-gpio for USB controllers of few devices
- Two sets of name and unit address check fixes for dts files.
- DMA, McASP, and timer and regulator related dts changes for dra7
- Add more devices for Nokia N9/N950
- Initial support for am335x ICEv2
- Initial support for am572x-IDK
- Pinctrl changes for am335x-baltos-ir5221
- Initial support for Amazon Kindle Fire (first generation)
- A series of changes to add GPIO controller support for the
GPMC driver. The driver changes will be merged separately.
- Support for am43xx clkout1
- Pinctrl and RTC changes for am335x-chili
- Add support for dra72-evm rev C (SR2.0)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=zZDR
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.7/dt-part1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Merge "First set of device tree changes for omaps for v4.7 merge window" from Tony Lindgren:
- Two sets of name and unit address check fixes for dts files.
- DMA, McASP, and timer and regulator related dts changes for dra7
- Add more devices for Nokia N9/N950
- Initial support for am335x ICEv2
- Initial support for am572x-IDK
- Pinctrl changes for am335x-baltos-ir5221
- Initial support for Amazon Kindle Fire (first generation)
- A series of changes to add GPIO controller support for the
GPMC driver. The driver changes will be merged separately.
- Support for am43xx clkout1
- Pinctrl and RTC changes for am335x-chili
- Add support for dra72-evm rev C (SR2.0)
* tag 'omap-for-v4.7/dt-part1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (61 commits)
ARM: dts: Add support for dra72-evm rev C (SR2.0)
ARM: dts: am335x-chilisom: Enable poweroff PMIC sequence using RTC signal
ARM: dts: am335x-chili*: Move Ethernet MAC description from SOM to board
ARM: dts: am335x-chili*: Move uart0 description from SOM to board
ARM: dts: am43xx: add support for clkout1 clock
ARM: dts: omap3-beagle: Provide NAND ready pin
ARM: dts: am335x: Provide NAND ready pin
ARM: dts: am437x: Provide NAND ready pin
ARM: dts: dra7x-evm: Provide NAND ready pin
ARM: dts: dm816x: Enable gpio controller for GPMC
ARM: dts: dm814x: Enable gpio controller for GPMC
ARM: dts: omap3: Enable gpio controller for GPMC
ARM: dts: am4372: Enable gpio controller for GPMC
ARM: dts: am335x: Enable gpio controller for GPMC
ARM: dts: dra7: Enable gpio controller for GPMC
ARM: dts: omap5: Enable gpio and interrupt controller for GPMC
ARM: dts: omap4: Enable gpio and interrupt controller for GPMC
ARM: dts: omap24xx: Enable gpio and interrupt controller for GPMC
ARM: dts: omap4-kc1: Power off support
ARM: dts: omap4-kc1: LEDs support
...
This commit adds pin-mux nodes for the NAND controller.
Some SoCs support 2 chip selects and the others only support
1 chip select.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- More i.MX6 System-on-Module board support from Ka-Ro electronics:
tx6s-8xxx, tx6u-8xxx, tx6q-1xxx, tx6ul-00xx.
- Nitrogen6_MAX QP and Nitrogen6_SoloX board support from Boundary
Devices.
- VF610 based ZII development board support.
- Add SAI interface audio support for i.MX6SX SDB board.
- A number of random updates on LS1021A and VF610 dts files.
- A couple of pinumx updates on i.MX25 and i.MX28.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXFHWaAAoJEFBXWFqHsHzOIVYH/j6uTUwEa5Ez5j933SDtPd16
fzL43h7WmMUUgKD4UlOyCSvsfILY5QfkVjEgneeYkBtxZA7T6YYpWE7SeNgjbqtW
GURIkWOf9vi4k0afJIaR44TZjfij2TDwEYO8ySPfjgrmtX7bJUtB0WxyiqrycSYh
ibJXnqGfhRxF3Htu+NBrp+NSgreBSqR+SXKQoP/xqzyKFDaFa3msL1YPIRIVrInI
t/bAvhmMfS5Or+0zZNXa0oem3DmnA+jbVmn/nFgzejsIA94c3Zr4yzKD7SvYDEDI
Ej4rwB40IWc7vNizbvg3xRhinwxbwD1emqPQm8rqxTpXiLrDn6QjCZocKfP+Wg0=
=c+YT
-----END PGP SIGNATURE-----
Merge tag 'imx-dt-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt
Merge "The i.MX device tree updates for 4.7" from Shawn Guo:
- More i.MX6 System-on-Module board support from Ka-Ro electronics:
tx6s-8xxx, tx6u-8xxx, tx6q-1xxx, tx6ul-00xx.
- Nitrogen6_MAX QP and Nitrogen6_SoloX board support from Boundary
Devices.
- VF610 based ZII development board support.
- Add SAI interface audio support for i.MX6SX SDB board.
- A number of random updates on LS1021A and VF610 dts files.
- A couple of pinumx updates on i.MX25 and i.MX28.
* tag 'imx-dt-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (36 commits)
ARM: dts: imx6qdl-udoo: add 7 inch LCD touchscreen panel support
ARM: dts: i.MX3x: add keypad port devicetree nodes
ARM: dts: ls1021a: add pix clock to DCU dts node
ARM: dts: ls1021a: DSPI has 6 chip-selects
ARM: dts: ls1021a: Add gpio support for ls1021a platform
ARM: dts: imx6q-ba16: Remove unused vqmmc-supply
ARM: dts: ls1021a: add SCFG MSI dts node
ARM: dts: imx28: add alternative pinmuxing for mac0
ARM: dts: imx6q-tbs2910: fix fec reset polarity
ARM: dts: vf610-zii-dev: Add ZII development board.
ARM: dts: vfxxx: add missing reg properties
ARM: dts: vf-colibri: increase NAND clock speed
ARM: dts: vf-colibri: alias the primary FEC as ethernet0
ARM: dts: imx6sx-sdb: Add SAI support
bindings: fsl-imx-sdma: Document 'fsl,sdma-event-remap' property
ARM: dts: imx6sx: Remove unused property
ARM: dts: imx6sx: Fix SAI DMA index
ARM: dts: imx6q-ba16: Disable pwm2 by default
ARM: dts: imx: add Boundary Devices Nitrogen6_SoloX board
ARM: dts: imx6qdl-sabresd: Pass the hannstar panel compatible string
...
A couple of patches that cleanup some Kconfig, enable various features,
use stdout-path to define the debug serial port (so that it doesn't have
to be manually specified on the kernel command-line) and cleanup and fix
some minor device trees bugs.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=YURX
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-4.7-arm' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/dt
Merge "ARM: tegra: Changes for v4.7-rc1" from Thierry Reding:
A couple of patches that cleanup some Kconfig, enable various features,
use stdout-path to define the debug serial port (so that it doesn't have
to be manually specified on the kernel command-line) and cleanup and fix
some minor device trees bugs.
* tag 'tegra-for-4.7-arm' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: tegra: Correct interrupt type for ARM TWD
ARM: tegra: Add stdout-path for various boards
ARM: tegra: Replace legacy *,wakeup property with wakeup-source
ARM: tegra: Enable watchdog support for Tegra114 and Tegra124
ARM: tegra: Add high speed UARTs to Jetson TK1 device tree
ARM: tegra: Fix copy/paste typo in several DTS includes
ARM: tegra: Remove redundant ARM_L1_CACHE_SHIFT_6 select
contains some clean-up and fixes of
device-tree data and addition of i2c1
node for DA850.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=oMYh
-----END PGP SIGNATURE-----
Merge tag 'davinci-for-v4.7/dt' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into next/dt
Merge "Device-Tree updates for DaVinci" from Sekhar Nori:
This contains some clean-up and fixes of device-tree data and addition
of i2c1 node for DA850.
* tag 'davinci-for-v4.7/dt' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: davinci: da8xx-dt: add OF_DEV_AUXDATA entry for i2c1
ARM: DTS: da850: add node for i2c1
ARM: dts: davinci: use proper address after @
ARM: DTS: da850: fix missing #gpio-cells in gpio node
- add hardware monitor support in the NSA320 device tree
- update makefile with kirkwood-ds112.dtb and kirkwood-nsa320.dtb
- fix GPIO config on the Linksys boards
- various Kirkwood DT warning fixup from the newer DT compiler
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlcPztkACgkQCwYYjhRyO9WdhgCfQQ1H5LT+C5WvS1OpXTKIScTo
of0AoJaa8PvkpVLB4e8mZVXfzBW9Ne6w
=nKfy
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt-4.7-1' of git://git.infradead.org/linux-mvebu into next/dt
Merge "mvebu dt for 4.7 (part 1)" from Gregory CLEMENT:
- add hardware monitor support in the NSA320 device tree
- update makefile with kirkwood-ds112.dtb and kirkwood-nsa320.dtb
- fix GPIO config on the Linksys boards
- various Kirkwood DT warning fixup from the newer DT compiler
* tag 'mvebu-dt-4.7-1' of git://git.infradead.org/linux-mvebu:
ARM: dts: kirkwood: Add DTS for Linksys EA4200v2/EA4500
ARM: dts: orion5x: add device tree for kurobox-pro
ARM: dts: kirkwood: Add address go regulator unit name
ARM: dts: kirkwood: Add address to mbus unit name
ARM: dts: kirkwood: Remove address from gpio-i2c unit name
ARM: dts: kirkwood: Fixup pcie DT warnings
ARM: dts: kirkwood: Add address to ethernet-phy unit name
ARM: dts: kirkwood: Remove address from dsa unit name
ARM: dts: kirkwood: Remove node address from leds
ARM: dts: kirkwood: Remove button address and fixup names
ARM: dts: kirkwood: add kirkwood-nsa320.dtb to Makefile
ARM: dts: kirkwood: add kirkwood-ds112.dtb to Makefile
ARM: mvebu: fix GPIO config on the Linksys boards
ARM: dts: kirkwood: Add the hardware monitor to the NSA320 device tree
1. Enable accelerated AES (Security SubSystem) on Exynos4412-based boards.
2. Enable HDMI CEC on Exynos4412-based Odroid.
3. Add regulator supplies for eMMC/SD on Odroid XU3/XU4.
4. Fix DTC unit name warnings.
5. Merge topic branch of new Artik5 board.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ha9R
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt
Merge "Samsung Device Tree updates and improvements for v4.7" from Krzysztof Kozlowski:
1. Enable accelerated AES (Security SubSystem) on Exynos4412-based boards.
2. Enable HDMI CEC on Exynos4412-based Odroid.
3. Add regulator supplies for eMMC/SD on Odroid XU3/XU4.
4. Fix DTC unit name warnings.
5. Merge topic branch of new Artik5 board.
* tag 'samsung-dt-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: s5p: Fix DTC unit name warnings in SMDKv210 board
ARM: dts: exynos: Fix DTC unit name warnings in Exynos5440
ARM: dts: exynos: Fix DTC unit name warnings in SMDK5420
ARM: dts: exynos: Fix DTC unit name warnings in Peach Pit
ARM: dts: exynos: Fix DTC unit name warnings in Exynos542x
ARM: dts: exynos: Fix DTC unit name warnings in Exynos5250
ARM: dts: exynos: Fix DTC unit name warnings in Exynos4x12
ARM: dts: exynos: Fix DTC unit name warnings in Trats2 board
ARM: dts: exynos: Fix DTC unit name warnings in Exynos4
ARM: dts: exynos: Fix DTC unit name warnings in Exynos3250
ARM: dts: exynos: Fix DTC unit name warnings in cros-adc-thermistors
ARM: dts: exynos: Add eMMC and SD regulator supplies to Odroid XU3/XU4
ARM: dts: exynos: Enable the HDMI CEC device on Exynos4412 Odroid boards
ARM: dts: exynos: Add node for the HDMI CEC device to exynos4
ARM: dts: exynos: Add HDMI CEC pin definition to exynos4 pinctrl
ARM: dts: exynos: Enable SSS on Odroid X/X2/U3 family
ARM: dts: exynos: Enable SSS on Trats2
ARM: dts: exynos: Add Security SubSystem node to Exynos4
Merge necessary new clocks from Sylwester (used by new board) and add support
for Exynos3250-based Artik5 board.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=mQfO
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-exynos3250-artik5-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt
Merge "Topic branch for Device Tree changes for Exynos 3250 for v4.7" from Krzysztof Kozlowski:
Merge necessary new clocks from Sylwester (used by new board) and add support
for Exynos3250-based Artik5 board.
* tag 'samsung-dt-exynos3250-artik5-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: Add MSHC2 DT node for SD card for exynos3250-artik5-eval board
ARM: dts: exynos: Add exynos3250-artik5 dtsi file for ARTIK5 module
ARM: dts: exynos: Add MSHC2 DT node for Exynos3250 SoC
ARM: dts: exynos: Add UART2 DT node for Exynos3250 SoC
ARM: dts: exynos: Add initial gpio setting of MMC2 device for exynos3250-monk
ARM: dts: exynos: Add initial pin configuration for exynos3250-rinato
clk: samsung: exynos3250: Add MMC2 clock
clk: samsung: exynos3250: Add UART2 clock
dt-bindings: Add the clock id of UART2 and MMC2 for Exynos3250
The MiQi is a rk3288-based devboard from Shenzen based mqmaker, with a
footprint the size of a credit card.
Main available outside connections are 4 usb ports, hdmi, gigabit
ethernet and two expansion headers.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
- Clockdomain fix for dra7 timer interrupts
- Two fixes for GPMC EDMA binding, I missed the need for a merge with
GPMC changes and EDMA changes
- Fix beagle-x15 eSATA by dropping misconfigured extcon_usb1
- Fix occasional external aborts on 36xx with PM that we've been
chasing for past few months. It turned out to be duplicate restore
of INTC registers that can in some cases cause us to hit erratum 1.106.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJXD8cCAAoJEBvUPslcq6VzKlEQAJsIi+p0Bk8ior9eqEphnWI5
NdMcu0POJb/SVLPfLzH5WxM/8Rd81Se56uiy1Hpa9cqxFxfStQm9/ltU/8EJEvAC
XnxwX78jfB7I6BcynKia+M/Sc4CgVxi41iq3lc1AUY5srN7kYyxFTljlMQMKwgTg
QFM4sFFCARUifO+z3SejgaO3vde0cMlZPh4gGYEx01xxYoqYk5kdWxHN1nRBH9T2
a/F7GrnMgTgALITP6oij9cb/uLyog7YraDc1fWQzAhm9JdneAbI21MHwkLsEB+Il
EDGcyq9VKMO8nXD2sGlt1EIjnaPZAd45To/OECGd11N7qog79/LEo5gMN/Is76kO
cx6nrvqGrOfynt2q3GyfMWiMRn36mk1gZ+FtOGCxRc0ROyqXfLyhKWKZkEK7aotf
R6Ga/ufNRiw0Ded0XABlt2PD6PPWD+Ly5wiU8AwOraM7XW6415FK07fD+hhZczOG
66wFC+J8nQGO7VecBrJOnqms2YnPlc4dgfVCo8jnAjRFtfPG9UjnPZBloxlDKMJB
OSkVPtRLCHiVk1xG51TCKgIgwJ5s957ohb9ImTIikXHsdLu39F3P7Tx4LQfYS8pd
B2AbktI0VYkJqiuaLjHdbxWBY8AL5UrZynn+pxjbVQcmuqgHGrDD7DWB8nmspvu0
4HvovFXCm8NvRZBMJhh9
=6rQp
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.6/fixes-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Merge "omap fixes for v4.6-rc cycle" from Tony Lindgren:
Fixes for omaps for v4.6-rc cycle:
- Clockdomain fix for dra7 timer interrupts
- Two fixes for GPMC EDMA binding, I missed the need for a merge with
GPMC changes and EDMA changes
- Fix beagle-x15 eSATA by dropping misconfigured extcon_usb1
- Fix occasional external aborts on 36xx with PM that we've been
chasing for past few months. It turned out to be duplicate restore
of INTC registers that can in some cases cause us to hit erratum 1.106.
* tag 'omap-for-v4.6/fixes-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP3: Fix external abort on 36xx waking from off mode idle
ARM: dts: am57xx-beagle-x15: remove extcon_usb1
ARM: dts: am437x: Fix GPMC dma properties
ARM: dts: am33xx: Fix GPMC dma properties
ARM: DRA7: clockdomain: Implement timer workaround for errata i874
DT changes for 4.7.
Also included is a DRM patch necessary to prevent regressions when
simplefb and vc4 drivers are both present. The patch was suggested by
the simplefb maintainer as the solution agreed upon at ELCE 2014, and
was acked by the DRM maintainer for merging through this tree.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=FqoL
-----END PGP SIGNATURE-----
Merge tag 'bcm2835-dt-next-2016-04-20' into devicetree/next
This pull request brings in VC4 devicetree support and the other minor
DT changes for 4.7.
Also included is a DRM patch necessary to prevent regressions when
simplefb and vc4 drivers are both present. The patch was suggested by
the simplefb maintainer as the solution agreed upon at ELCE 2014, and
was acked by the DRM maintainer for merging through this tree.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Controller is present on every BCM4708* board but only few devices have
serial flash attached so mark it as disabled by default.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
* Correct preset_lpj calculation which may lead to too short delays
* Correct handling of optional clocks on r8a7791 to restore
access to the serial port the porter board
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=k7qU
-----END PGP SIGNATURE-----
Merge tag 'renesas-fixes-for-v4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes
Merge "Renesas ARM Based SoC Fixes for v4.6" from Simon Horman:
Renesas ARM Based SoC Fixes for v4.6
* Correct preset_lpj calculation which may lead to too short delays
* Correct handling of optional clocks on r8a7791 to restore
access to the serial port the porter board
* tag 'renesas-fixes-for-v4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: timer: Fix preset_lpj leading to too short delays
Revert "ARM: dts: porter: Enable SCIF_CLK frequency and pins"
ARM: dts: r8a7791: Don't disable referenced optional clocks
that broke when we added runtime based SoC revision detection earlier.
It seems suspend worked earlier as things were only partially initialized,
while now we initialize things properly for dra7.
Note that the "ARM: OMAP: Catch callers of revision information prior
to it being populated" had to be reverted as it caused bogus warnings
for other SoCs because omap initcalls bail out based on revision being
set to 0 for other SoCs. These initcalls will mostly just disappear
when we drop support for omap3 legacy booting.
Also included is a fix for dra7 sys_32k_ck clock source that is not
enabled on boot making system fall back to using emulated clock.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=0X4E
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.6/fixes-rc2-v2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Merge "omap fixes against v4.6-rc2" from Tony Lindgren
Fixes for omaps against v4.6-rc2, mostly to fix suspend for beagle-x15
that broke when we added runtime based SoC revision detection earlier.
It seems suspend worked earlier as things were only partially initialized,
while now we initialize things properly for dra7.
Note that the "ARM: OMAP: Catch callers of revision information prior
to it being populated" had to be reverted as it caused bogus warnings
for other SoCs because omap initcalls bail out based on revision being
set to 0 for other SoCs. These initcalls will mostly just disappear
when we drop support for omap3 legacy booting.
Also included is a fix for dra7 sys_32k_ck clock source that is not
enabled on boot making system fall back to using emulated clock.
* tag 'omap-for-v4.6/fixes-rc2-v2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (198 commits)
Revert "ARM: OMAP: Catch callers of revision information prior to it being populated"
ARM: OMAP: Catch callers of revision information prior to it being populated
ARM: dts: dra7: Correct clock tree for sys_32k_ck
ARM: OMAP: DRA7: Provide proper class to omap2_set_globals_tap
ARM: OMAP: DRA7: wakeupgen: Skip SAR save for wakeupgen
Linux 4.6-rc2
v4l2-mc: avoid warning about unused variable
Convert straggling drivers to new six-argument get_user_pages()
.mailmap: add Christophe Ricard
Make CONFIG_FHANDLE default y
mm/page_isolation.c: fix the function comments
oom, oom_reaper: do not enqueue task if it is on the oom_reaper_list head
mm/page_isolation: fix tracepoint to mirror check function behavior
mm/rmap: batched invalidations should use existing api
x86/mm: TLB_REMOTE_SEND_IPI should count pages
mm: fix invalid node in alloc_migrate_target()
include/linux/huge_mm.h: return NULL instead of false for pmd_trans_huge_lock()
mm, kasan: fix compilation for CONFIG_SLAB
MAINTAINERS: orangefs mailing list is subscribers-only
net: mvneta: fix changing MTU when using per-cpu processing
...
Add support for board based on the popular Altera Cyclone V SoC.
This board has the following properties:
- 1 GiB of DRAM
- 1 Gigabit ethernet
- 1 USB gadget port
- 1 USB host port with an on-board hub
- 2 QSPI NORs connected to the Cadence QSPI core
- Multiple I2C EEPROMs and one I2C temperature sensor
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
The SSP0/SPI1 and SSP1/SPI2 shared pinout and should be disable by
default.
Board specific dts should enable them, as needed.
Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Preparatory change prior to disabling SSPx controllers
by default in the shared LPC32xx DTSI file.
Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
The change adds clock properties to spi peripheral devices,
clock ids are taken from dt-bindings/clock/lpc32xx-clock.h
Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Taken from the datasheet.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add support for battery level reading on the Nexus7 by
enabling the bq27541 driver in the nexus7 dts
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Arnd Bergmann <arnd.bergmann@linaro.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Andy Gross <agross@codeaurora.org>
Cc: Vinay Simha BN <simhavcs@gmail.com>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Stephen Boyd <stephen.boyd@linaro.org>
Cc: linux-arm-msm@vger.kernel.org
Cc: devicetree@vger.kernel.org
Signed-off-by: John Stultz <john.stultz@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds support to on board LIS3MDLTR magnetometer.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds spi nodes required to provide spi bus support on LS
expansion.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds nodes required to enable 4 i2c buses on the board which
are connected to various sensors and eeprom.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds support to 4 user leds, wlan and bt led on board.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch enables sata and regulators required to get on board sata
working.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds pcie and regulators required to get on board ATL1C
ethernet working.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds usb host and otg support on board with required
regulators.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds eMMC and SD card support with card detect and adding
required regulators.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds pmic regulator supplies connected on the board.
Rest of the invidual regulators would be added as and when required by
the devices.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds support to DB600c with basic serial ports.
DB600c is based on APQ8064.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds support to gsbi7 i2c which is used in some of the new
boards.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds support to gsbi1 uart and its pinctrls nodes.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch fixes pinctrls for spi and i2c nodes whose default and sleep
states are together, which is incorrect.
Without this patch i2c/spi would not be functional.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
"PHONY += FORCE" is already cared by scripts/Makefile.build,
which these files are included from.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Michal Marek <mmarek@suse.com>
Since commit 2aedcd098a ('kbuild: suppress annoying "... is up to
date." message'), $(call if_changed,...) is evaluated to "@:"
when there is nothing to do.
We no longer need to add "@:" after $(call if_changed,...) to
suppress "... is up to date." message.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Michal Marek <mmarek@suse.com>
One part of the efs memory region is used specifically for sharing file system
buffers between the apps and modem cpus (aka rmtfs), so better reflect this
split.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This adds the blsp_dma node to the device tree and the required
properties for using DMA with serial
Signed-off-by: Matthew McClintock <mmcclint@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This adds the crypto nodes to the ipq4019 device tree, it also adds the
BAM node used by crypto as well which the driver currently requires to
operate properly
The crypto driver itself depends on some other patches to qcom_bam_dma
to function properly:
https://lkml.org/lkml/2015/12/1/113
CC: Stanimir Varbanov <svarbanov@mm-sol.com>
Signed-off-by: Matthew McClintock <mmcclint@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This adds some operating points for cpu frequeny scaling
Signed-off-by: Matthew McClintock <mmcclint@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This will allow boards to enable the I2C bus
CC: Sricharan R <srichara@qti.qualcomm.com>
Signed-off-by: Matthew McClintock <mmcclint@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This will allow boards to enable the SPI bus
Signed-off-by: Matthew McClintock <mmcclint@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This will allow these types of boards to be rebooted.
Signed-off-by: Matthew McClintock <mmcclint@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This will allow boards to enable watchdog support
Signed-off-by: Matthew McClintock <mmcclint@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This adds the required device tree nodes to bring up the
secondary cores on the ipq4019 SoC.
Signed-off-by: Matthew McClintock <mmcclint@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Initial board support dts files for DK01 board.
Signed-off-by: Senthilkumar N L <snlakshm@codeaurora.org>
Signed-off-by: Varadarajan Narayanan <varada@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add initial dts files and SoC support for IPQ4019
Signed-off-by: Varadarajan Narayanan <varada@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Adding reset-gpio-active-high boolean DT binding property, which we need to
make PCIe working on Apalis SoMs and not break old DTBs. While at it, I've
fixed comment and GPIO polarity.
On Apalis SoMs the GPIO1_IO28 used to PCIe reset is not connected directly
to PERST# PCIe signal, but it's ORed with RESETBMCU coming off the PMIC,
and thus is inverted, active-high.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This patch adds the CPU node of the BCM2835 into the DT.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
The ARM TWD interrupt is a private peripheral interrupt (PPI), and per
the ARM GIC documentation, whether the type for PPIs can be set is
IMPLEMENTATION DEFINED.
For R-Car H1 devices the PPI type cannot be set, and so when we attempt
to set the type for the ARM TWD interrupt it fails. This has gone
unnoticed because it fails silently, and because we cannot re-configure
the type it has had no impact. Nevertheless fix the type for the TWD
interrupt so that it matches the hardware configuration.
Based on patches by Jon Hunter for Tegra20/30 and OMAP4.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The ARM TWD interrupt is a private peripheral interrupt (PPI), and per
the ARM GIC documentation, whether the type for PPIs can be set is
IMPLEMENTATION DEFINED.
For SH-Mobile AG5 devices the PPI type cannot be set, and so when we
attempt to set the type for the ARM TWD interrupt it fails. This has
gone unnoticed because it fails silently, and because we cannot
re-configure the type it has had no impact. Nevertheless fix the type
for the TWD interrupt so that it matches the hardware configuration.
Based on patches by Jon Hunter for Tegra20/30 and OMAP4.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add IIC nodes to r8a7794 device tree.
Based on similar work for the r8a7793 by Laurent Pinchart.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add IIC clocks to r8a7794 device tree.
Based on similar work for the r8a7790 by Wolfram Sang.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
The R-Car CAN controllers can derive the CAN bus clock not only from their
peripheral clock input (clkp1) but also from the other internal clock
(clkp2) and external clock fed on CAN_CLK pin. Describe those clocks in
the device tree along with the USB_EXTAL clock from which clkp2 is
derived.
Based on work by Sergei Shtylyov for the r8a7791 SoC.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add CAN nodes to r8a7794 device tree.
Based on work by Sergei Shtylyov for the r8a7791 SoC.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Add CAN nodes to r8a7794 device tree.
Based on work by Sergei Shtylyov for the r8a7791 SoC.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Based on Rev. 2.00 of the R-Car Gen2 datasheet.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This reverts commit 19417bd9c5 ("ARM: dts: porter: Enable SCIF_CLK
frequency and pins") as according to
http://elinux.org/File:R-CarM2-KOELSCH_PORTER-B_PORTER_C_Comparison.pdf
the external oscillator for SCIF_CLK is not mounted on the porter boards.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
clk_get on a disabled clock node will return EPROBE_DEFER, which can
cause drivers to be deferred forever if such clocks are referenced in
their clocks property.
Update the various disabled external clock nodes to default to a
frequency of 0, but don't disable them to prevent this.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Obviously, these are PHONY targets.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add interrupt-names properties to dt and apply the correct
mapping between irq and dma channels.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The DRAM gates control whether the image / display devices on the SoC have
access to the DRAM clock or not.
Enable it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
It turns out that the A13 / R8 also have a tve encoder block, and a gate
for it.
Add it to the DT.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Enable the pll3 and pll7 clocks in the DT that are used to drive the
display-related clocks.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This patch changes SROM nodes compatible from generic to model specific
to match with binding documentation. Also updating property
"samsung,srom-page-mode" as it is not defined as bool instead of int
Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
The official UDOO board kit has 7 and 15.6 inch touchscreen LCD panels
as options.
This patch adds support for 7 inch panel only, but the 15.6 inch one
should be easy to add using the same regulator, backlight device and
LVDS channel.
Since this panel is an option for UDOO board it is disabled by default
and can be enabled (for example) by the following U-Boot commands:
fdt set backlight status okay
fdt set panelchan status okay
fdt set panel7 status okay
fdt set touchscreenp7 status okay
The LVDS channels is also disabled by default to avoid warning from its
driver.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the Keypad Port (KPP) devicetree nodes for IMX31 and IMX35 SOC.
Signed-off-by: Alexander Kurz <akurz@blala.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Probably most of NXP LPC32xx boards have 13MHz main oscillator and
therefore for HCLK PLL and ARM core clock rate default hardware
setting is 16 * 13MHz = 208MHz, however a user may vary HCLK PLL/ARM
core rate from 156MHz to about 266MHz for 13MHz clock source.
The change explicitly defines HCLK PLL output rate to default 208MHz
to overwrite any settings done by a bootloader, if needed it can be
redefined in a board DTS file.
Acked-by: Sylvain Lemieux <slemieux.tyco@gmail.com>
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
The edp-phy control is a part of the General Register Files and
with a recent patch in 4.6 the phy driver can now also handle this
correctly, so move the dts node under the GRF as well.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Similar to the pmu, the general register files contain a lot of different
setting bits grouped into general registers, but also some somewhat special
entities like the controls for some phy-blocks or the io-voltage control.
To be able to move these blocks under the grf node where they actually
belong, make it a simple-mfd.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add the Security Controller (SCC) module to the dtsi.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
DRA72-EVM now has an upgrade to Rev C with SR2.0 silicon. As part of
this change, a few updates were factored in that were software
incompatible with previous board in few areas:
- We now use DP83867 ethernet phy instead of older DP838865 which fails
in certain use cases.
- Two Ethernet ports now instead of the single one in rev B.
- polarities changed for certain pcf gpios
- Due to SoC phy current requirements, VDDA supplies are split between
ldo3 and ldo2 (ldo2 was previously unused). NOTE: DSS (VDDA_VIDEO) is
still supplied by ldo5, HDMI is now supplied by LDO2 instead of using
LDO3.
NOTE: It does not make much sense to spin off a new board compatible
flag since there is no real benefit for the same.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
ChiliSOM has TPS65217's PWR_EN pin connected to AM335x PMIC_POWER_EN
pin. Processor's PMIC_POWER_EN is controlled by it's internal RTC, hence
RTC subsystem is responsible for proper board poweroff sequence.
This change enables complete poweroff sequence for ChiliBoard, switching
PMIC's state from ACTIVE to SLEEP.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
ChiliSOM has 2 Ethernet subsystems with different types of possibly used
PHY interfaces (i.e. MII, RMII, GMII, RGMII). Current code configured
pinmux for RMII on 1st Ethernet subsystem and enabled Ethernet MAC with
1 slave for all boards which use ChiliSOM.
This change moves pinmux configuration of 1st Ethernet subsystem to
ChiliBoard description, as this is board-specific.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
uart0 configuration code has been in SOM. However, it is possible to
use all (or none) of 6 uart's of AM335x processor present on ChiliSOM.
This fix moves declaration of uart0 from ChiliSOM to ChiliBoard, because
use of uart is strictly board-specific.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This adds the DMA engine to the Nomadik and assigns the UART
DMA channels. Both slave DMA for UARTs and the memcpy engine
works fine, tested on the Nomadik NHK15.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The LIS3LV02DL accelerometer on the Nomadik NHK15 can generate
IRQs by the DRDY line. Map this in the DTS file and set up the
pin as input to the SoC.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This platform is based on a Marvell 88E6282 SoC and 88E6171 switch.
[gregory.clement@free-electrons.com: fix block comment style]
Signed-off-by: Bert Vermeulen <bert@biot.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Imre Kaloz <kaloz@openwrt.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Add dts file to support Buffalo/Revogear Kurobox-Pro, which is marvell
orion5x based 3.5" HDD NAS.
It's a quite old product and already discontinued. So there's no
official website for it. But it was an early product which used marvell
orion5x 88F5182 chipset, it's popular in the community.
Some unofficial site:
- http://buffalo.nas-central.org/wiki/Category:KuroboxPro
- http://nice.kaze.com/KUROPRO_ProductSpecifications.pdf
This device tree is based on the board file:
arch/arm/mach-orion5x/kurobox_pro-setup.c
However, the probing order of NAND and JEDEC-Flash are different from
the original board file, this results in incompatible minor number
for a few /dev/mtdX and /dev/mtdblockX devices.
So I still want to keep the board file for the time being.
Signed-off-by: Roger Shimizu <rogershimizu@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The regulator has a reg property so include it in the unit name.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
gpio-i2c does not have a reg property, just a list of gpios.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
PCIe has a range property, so the unit name should contain an address.
Make use of the label to enable individual PCIe busses. Also, fixup
the synology dtsi file which added a label pcie2 rather than using the
existing pcie1 label.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
PHYs have an address on the mdio bus. So the unit name should contain
an address. This is complicated in that some .dtsi files contain the
node, but the reg is set in the .dts file. In this case, use the
abstract address X.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The dsa node does not have a reg property, so remove the address from
the unit name.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
leds don't have a reg property, so remove the address from the unit name.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The DT compiler is now warning about unit names with addresses but not
reg property. Fix all the gpio-key buttons which causes warnings.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
da850 has two I2C controllers, but the node for i2c1 was missing.
Add node for i2c1 controller and i2c1 pinmux pins.
Signed-off-by: Petr Kulhavy <petr@barix.com>
[nsekhar@ti.com: fix indentation]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
TI has been using the physical address in DT after the @ in device nodes.
The device tree convention is to use the same address that is used for
the reg property. This updates all davinci DT files to use the proper
convention.
Signed-off-by: David Lechner <david@lechnology.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
The gpio node is missing the mandatory property #gpio-cells, which is
causing runtime errors when using GPIOs e.g. with gpio-leds or gpio-keys:
"could not get #gpio-cells for /soc/gpio@1e26000"
This fixes the problem and adds the missing parameter.
The value is 2 according to the gpio-davinci.txt binding.
Signed-off-by: Petr Kulhavy <petr@barix.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
as well as general display+hdmi support on rk3036. With the Analogix
DP support, Veyron Chromeboks can now finally use their internal
display.
Other than this big improvement we have thermal support on the rk3228,
a long time missing binding document for the General Register Files
block, better operating points for Veyron devices and a bunch of fixes
with parts stemming from warnings that new dtc version can generate.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCAAGBQJXDI8tAAoJEPOmecmc0R2BwksIAK/l/K03RwWzT20pc9UZIBPL
YevlAXKFa7io9Wju0gfGJOQNo+UAUQh6Rhcuf/J3odiDl2URoHqu1xIR+KOKWZrO
aD72VorCOcrPYck3BTyTLCtfG+zr8Q3t/i5f3ghitK5XdnW2MtE6SIjZ5x8Md+M8
6D4svbgLIh16/kq1XzjcQkf5c7sf7xSABhZEE8Xb7CuPmeBe/j6ORMMuUqIA0rJi
ZbW0+MyAiuAYD7vyQm/IiPk9nw12nnD+zjVg3Nz3YwmXYb4cNQfHdCJbjxezbw80
R96VS4OdAlOZocETi5GljC97fdAtTSBJXOogeK1/pXQfbQFlkWeDYzsF9l/oJYI=
=+WKk
-----END PGP SIGNATURE-----
Merge tag 'v4.7-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
A lot display-controller nodes for DSI and the Analogix DP on rk3288
as well as general display+hdmi support on rk3036. With the Analogix
DP support, Veyron Chromeboks can now finally use their internal
display.
Other than this big improvement we have thermal support on the rk3228,
a long time missing binding document for the General Register Files
block, better operating points for Veyron devices and a bunch of fixes
with parts stemming from warnings that new dtc version can generate.
* tag 'v4.7-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip: (27 commits)
ARM: dts: rockchip: move rk3036 memory definition to board files
ARM: dts: rockchip: enable the eDP on rk3288 veyron devices
ARM: dts: rockchip: simple panel and backlight supplies on veyron boards
ARM: dts: rockchip: override edp hpd handling on veyron-pinky and speedy
ARM: dts: rockchip: add rk3288-veyron-minnie backlight and panel settings
ARM: dts: rockchip: add rk3288-veyron-jaq backlight and panel overrides
ARM: dts: rockchip: add core rk3288-veyron backlight and panel nodes
ARM: dts: rockchip: add startup delay to rk3288-veyron panel-regulators
ARM: dts: rockchip: move edp-hpd pin definition into common location
ARM: dts: rockchip: add rk3288 displayport controller node
ARM: dts: rockchip: add rk3288 edp-phy node
ARM: dts: rockchip: add missing unitname to cpu_leakage efuse
ARM: dts: rockchip: drop unneeded properties from mipi node
ARM: dts: rockchip: clean up gpio-keys nodes
ARM: dts: rockchip: fix missing usbphy unit-names
ARM: dts: rockchip: fix rk3288 power-domain unit names
ARM: dts: rockchip: update rk3288-veyron cpu operating points
ARM: dts: rockchip: remove broken-cd from emmc and sdio
ARM: dts: rockchip: enable the tsadc for rk3228 evb
ARM: dts: rockchip: add the thermal main info found on rk3228
...
Signed-off-by: Olof Johansson <olof@lixom.net>
- Update SD/MMC node for Arria10
- Update Arria10 with clock and interrupt fields for DMA
- Remove 'phy-addr' from stmmac node
- Remove ethernet node from Cyclone5 DTSI
- Add LEDs/KEYs/SWs support on Sockit
- Add L2 and OCRAM EDAC dts entries
- Add reset control for USB
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJXC/fUAAoJEBmUBAuBoyj0VsYP/3X4YaZ7zf/meoPi2xwJmzyf
a9PUslTJ1GAs5p+0b20UdwSX0BQHrDKIZvhQ53ThAGbS3mQPEtlDP8bjhAFspjYL
85FEvtLvS4HvMwopiUwHx+INnoL79KUnHMn1Y+A5QLAFq2vJe1frP2KnAiJX9HZr
a3f4Eix7fI8qpa2ixXK9GnUppAhFVDqZ0RuxgXewGvWGyPykLHnl63FvfNgCZx6L
s+8iGDMhsVwah9Kdv/OJielLeQqaQGeSE5+5t+YNszISyGatiwr2e/yx7//tjQwS
f8Y6ck1P2N8ncWwJX0PiJxo0ssrLkfhqJS3YlB0OLCE/IwC8hUFAxEnUonb70owR
jjpBzsPynARCdr3WuAu61FH2xGs4OfBryXUVhTIcB+XeNAcO5p+pBJu8pFA6PlM3
MQsu7AwfpPlUWwaRLagRd/o86rhwf31YkcHt2F9UYwjyYUeqNlZSoPgf8NvIYILo
f+qkV5mywWiZAtilT500byyWbivsEzjbjmpV4l+QMYvIYYbIwmPi2y78A/6l/ZKw
xon/OzcH4Jtu/u4Bc4GL3S1yFPDlf8KrL1So47BZy6/Y7XLxf0lfE/PtDA+k7Eq1
nUL4E6zf5KOAWizye0aDcMt4Sos9+7lxeHzu/CVPpgu4QXfk06fkVD5ePlZ72HBq
Bt2Z9KtLFusBEJTvB5hk
=gT7+
-----END PGP SIGNATURE-----
Merge tag 'socfpga_dts_for_v4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux into next/dt
SoCFPGA DTS updates for v4.7
- Update SD/MMC node for Arria10
- Update Arria10 with clock and interrupt fields for DMA
- Remove 'phy-addr' from stmmac node
- Remove ethernet node from Cyclone5 DTSI
- Add LEDs/KEYs/SWs support on Sockit
- Add L2 and OCRAM EDAC dts entries
- Add reset control for USB
* tag 'socfpga_dts_for_v4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
ARM: dts: socfpga: add reset control for USB
ARM: dts: socfpga: Add Altera Arria10 OCRAM EDAC devicetree entry
ARM: dts: socfpga: Add Altera Arria10 L2 Cache EDAC devicetree entry
ARM: dts: socfpga: Add support for HPS KEYs/SWs on SoCKit
ARM: dts: socfpga: Add support for HPS LEDs on SoCKit
ARM: dts: socfpga: Drop gmac0 from CV dtsi
ARM: dts: socfpga: Drop phy-addr OF property from CV dtsi
ARM: dts: socfpga: Add missing clock and interrupt fields for Arria10 DMA
ARM: dts: socfpga: add the clk-phase property for sd/mmc clock
ARM: dts: socfpga: add cap-sd-highspeed for SD/MMC node
Signed-off-by: Olof Johansson <olof@lixom.net>
- CREG clock controller
- Real Time Clock (RTC)
- Analog peripherals (ADC/DAC)
- Warning fixes for the new dtc compiler
With the CREG clock controller in place it is now possible
to enable the internal RTC on LPC18xx/43xx platforms. The
analog peripherals (ADC/DAC) has also been added here and
enabled on both the EA4357 dev kit and Hitex eval board.
In addition to the new entries there are a fixes for the
DT warnings generated by the new dtc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABCAAGBQJXAs9CAAoJEF5zSH4+/j/a6ZoIAKxH1719KAQ7QBAvegmeQxvJ
qV9cp+zcg2mqbB8QtL1Bl0BH1E/BhjtI9lRia5tNe68z/reGePb7CSxC4aK5FfWs
BEIk8Io3VWCjq+ZMc88VHSa2uJo/v4mxV5Lc3LquiJYtBZnnvf0u8f1pAE9lR021
KgdkO0qWPeJUOEOghSZ4jwWTZBBtkxa+5WqOLwvM8lokFIHey0GBTcAIb77gOIqD
27oU0YCo83xCOLUBlUZMHpLiYjQZtSfROJdysEYu1rn5hrL16G3Bj0TkdWMyw5Wf
r5HC+qBBc2qqVK/CRZnYQFAOZlGUjrbMHdrjpzkILWYbsbV29XCymn4p/QDO6bo=
=Y9wO
-----END PGP SIGNATURE-----
Merge tag 'lpc18xx_dts_for_4.7' of https://github.com/manabian/linux-lpc into next/dt
Device Tree additions for LPC18xx platform
- CREG clock controller
- Real Time Clock (RTC)
- Analog peripherals (ADC/DAC)
- Warning fixes for the new dtc compiler
With the CREG clock controller in place it is now possible
to enable the internal RTC on LPC18xx/43xx platforms. The
analog peripherals (ADC/DAC) has also been added here and
enabled on both the EA4357 dev kit and Hitex eval board.
In addition to the new entries there are a fixes for the
DT warnings generated by the new dtc.
* tag 'lpc18xx_dts_for_4.7' of https://github.com/manabian/linux-lpc:
dt-bindings: phy-lpc18xx-usb-otg: remove unit address from binding
ARM: dts: lpc4350-hitex-eval: fix unit name warnings from dtc
ARM: dts: lpc4357-ea4357: fix unit name warnings from dtc
ARM: dts: lpc18xx: remove unit addresses from creg childs
ARM: dts: armv7-m: add unit name to interrupt-controller
ARM: dts: lpc4350-hitex-eval: add adc1
ARM: dts: lpc4357-ea4357: add dac
ARM: dts: lpc4357-ea4357: add adc0
ARM: dts: lpc18xx: add dac node
ARM: dts: lpc18xx: add adc nodes
ARM: dts: lpc18xx: add rtc node
ARM: dts: lpc18xx: add creg-clk node
Signed-off-by: Olof Johansson <olof@lixom.net>
- Add CLCD panel nodes to PB1176 and PB11MPCore
- Add a DT binding blurb for the Versatile IB2 syscon
- Add DTS files for the (QEMU supported) RealView EB
boards in all variants.
- Add DTS files for the (QEMU supported) RealView PBA8
and PBX-A9 board variants.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=3eW6
-----END PGP SIGNATURE-----
Merge tag 'versatile-dts-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator into next/dt
Versatile DTS changes, baseline for the v4.7 series:
- Add CLCD panel nodes to PB1176 and PB11MPCore
- Add a DT binding blurb for the Versatile IB2 syscon
- Add DTS files for the (QEMU supported) RealView EB
boards in all variants.
- Add DTS files for the (QEMU supported) RealView PBA8
and PBX-A9 board variants.
* tag 'versatile-dts-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator:
ARM: dts: realview: DT support for the PBA8 and PBX-A9
ARM: dts: realview: support all the RealView EB board variants
ARM: dts: realview: PB1176: define a standard VGA panel
ARM: dts: realview: PB11MPCore: define a standard VGA panel
Documentation/DT: add blurb for IB2 syscon to Versatile
Signed-off-by: Olof Johansson <olof@lixom.net>
USB1 controller is hardwired to be used as Host only port so
we don't need to check ID pin state and can get rid of extcon_usb1.
This also reduces USB1 controller's and so eSATA power's dependency
with EXTCON. This fixes eSATA port with multi_v7_defconfig.
Cc: Franklin S Cooper Jr. <fcooper@ti.com>
Cc: Vagrant Cascadian <vagrant@debian.org>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Tested-by: Franklin S Cooper Jr. <fcooper@ti.com>
[tony@atomide.com: updated to describe what it fixes]
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch updates the GPMC's DT DMA property to reflect the updated eDMA
bindings.
Fixes: cce1ee0001 ("ARM: DTS: am437x: Use the new DT bindings for the eDMA3")
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch updates the GPMC's DT DMA property to reflect the updated eDMA
bindings.
Fixes: b5e5090660 ("ARM: DTS: am33xx: Use the new DT bindings for the eDMA3")
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
clkout1 clock node and its generation tree was missing. Add this based
on the data on TRM and PRCM functional spec.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
There are few devices that have USB power controlled using GPIO. Linux
USB host driver (bcma-hcd) already supports this by reading vcc-gpio
from DT. Set it properly for all known devices.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This commit adds definition for cpu_on, cpu_off and cpu_suspend commands.
These definitions must match the corresponding PSCI definitions in
boot monitor.
Having those command and corresponding PSCI support in boot monitor allows
run time CPU hot plugin.
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
Add aliases for SPI nodes, this is required to probe the SPI devices in
U-Boot.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
As reported in [1], rename the k2* dts files to keystone-* files
this will force consistency throughout.
Script for the same (and hand modified for Makefile and MAINTAINERS
files):
for i in arch/arm/boot/dts/k2*
do
b=`basename $i`;
git mv $i arch/arm/boot/dts/keystone-$b;
sed -i -e "s/$b/keystone-$b/g" arch/arm/boot/dts/*[si]
done
NOTE: bootloaders that depend on older dtb names will need to be
updated as well.
[1] http://marc.info/?l=linux-arm-kernel&m=145637407804754&w=2
Reported-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
The DCU IP has distinct clock inputs for register access and the
pixel clocks, at least in some implementations. LS1021a seems to
use the same clock, therefore specify the same clock for "dcu"
and "pix".
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Both DSPI have signals SPIn_PCS[0:5] so in summary 6 chip-selects, not 5.
Fix that.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add gpio nodes for ls1021a platform dts file. The gpio
IP block of the ls1021a can be supported by the code
drivers/gpio/gpio-mpc8xxx.c.
The compatible "fsl,qoriq-gpio" is used by gpio driver:
drivers/gpio/gpio-mpc8xxx.c to implement general gpio
functionalities.
The chip-specific compatible "fsl,ls1021a-gpio" may be
used to fix potential gpio IP block errata or other
chip-specific gpio issues.
Signed-off-by: Liu Gang <Gang.Liu@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The vqmmc supply is not connected to bio supply on the BA16 module.
Hence remove vqmmc-supply property in usdhc3 node.
Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add SCFG MSI dts node and add msi-parent property to PCIe dts node
that points to the corresponding MSI node.
Signed-off-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Tested-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to Documentation/devicetree/bindings/net/fsl-fec.txt the polarity
of "phy-reset-gpios" is assumed to be active-low unless a separate property
"phy-reset-active-high" is available. So replace the inconsistent polarity
description to make the correct active-low reset behavior more obvious.
Signed-off-by: Soeren Moch <smoch@web.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This commit adds support for Rev. B of a Zodiac Inflight Innovations
development board, mainly intended for DSA and ARINC 429 development
work.
Signed-off-by: Cory Tusar <cory.tusar@pid1solutions.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add missing reg properties to AIPS bus and Cortex-A5's PMU unit.
This change avoids the following warnings:
Warning (unit_address_vs_reg): Node /soc/aips-bus@40000000 has a unit
name, but no reg property
Warning (unit_address_vs_reg): Node /soc/aips-bus@40080000 has a unit
name, but no reg property
Warning (unit_address_vs_reg): Node /soc/aips-bus@40080000/pmu@40089000
has a unit name, but no reg property
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The NAND flash memory populated on Colibri VF61 allows faster NAND
timings than the flash memory on VF50. Additionally, due to divider
limitations, VF61 did clock the flash even slower than VF50. Assign
the NFC clock in the module specific device trees vf500-colibri.dtsi
and vf610-colibri.dtsi respectively.
This increases raw read speed on Colibri VF61 by about 20%.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The Vybrid based Colibri modules provide a on-module PHY which is
connected to the second FEC instance FEC1. Since the on-module
Ethernet port is considered as primary ethernet interface, alias
fec1 as ethernet0. This also makes sure that the first MAC address
provided by the boot loader gets assigned to the FEC instance used
for the on-module PHY.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Introduce imx6sx-sdb-sai.dts so that it is possible to use the
SAI interface.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Property 'dma-source' is not used anywhere, nor it is documented, so
let's just get rid of it.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to sdma_peripheral_type in include/linux/platform_data/dma-imx.h
IMX_DMATYPE_SAI corresponds to index 24, so fix it accordingly.
Suggested-by: Zidan Wang <zidan.wang@nxp.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
pwm2 is provided on the BA16 Q7 module, but is not used on any
of the current configurations. However, future platforms may
utilize this device, so we are simply disabling the node rather
than removing it completely.
Signed-off-by: Justin Waters <justin.waters@timeys.com>
Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
It is preferred to use the panel compatible string rather than passing the
LCD timings in the device tree.
So pass the "hannstar,hsd100pxn1" compatible string to describe
the LVDS panel on this board.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Geert Uytterhoeven