The new HDP flush method doesn't seem to work reliably on
sDMA either, so use the old method here too.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
To plug the VRAM memory leak (see previous patch for
details) we must unpin the frame buffer when disabling the
CRTC. This warrants the addition of disable function for legacy
CRTC, which puts the CRTC in DPMS-OFF state and unpins the
frame buffer if there is one associated with the CRTC.
Signed-off-by: Ilija Hadzic <ihadzic@research.bell-labs.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When drm_helper_disable_unused_functions calls disable
function of the CRTC, it also sets the crtc->fb pointer
to NULL. This can later (when the mode on that CRTC is setup
again from user space) cause ***_do_set_base functions to
"think" that there is no old buffer and skip the unpinning
code. Consequently, the buffer that has been NULL-ified in
drm_helper_disable_unused_functions will never be unpinned
causing a leak in VRAM.
This patch plugs the leak by unpinning the frame buffer
in crtc_disable function.
Signed-off-by: Ilija Hadzic <ihadzic@research.bell-labs.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The current code writing SADs to the audio registers seems to assume
that there is at most a single SAD per audio format.
However, that is not the case. Especially for PCM it is somewhat common
for sinks to have two SADs, one for 8-channel and one for 2-channel
audio, which may have different supported sample rates (i.e. the sink
supports stereo audio at higher sample rates than multichannel audio).
Because of this, only the 2-channel SAD may be used if it appears before
the 8-channel SAD. Unless other SADs require otherwise, this may cause
the ALSA HDA driver to allow stereo playback only.
Fix the code to pick the PCM SAD with the highest number of channels,
while merging the rate masks of PCM SADs with lower amount of channels
into the additional stereo rate mask byte.
Technically there are even more cases to handle (multiple non-PCM SADs
of the same type, more than two PCM SADs with varying channel counts,
etc), but those have not actually been encountered in the field and
handling them would be non-trivial.
Example affected EDID from Onkyo TX-SR674 specifying 192kHz stereo
support and 96kHz 8-channel support (and other 8-channel compressed
formats):
00ffffffffffff003dcb010000000001
ffff0103800000780a0dc9a057479827
12484c00000001010101010101010101
010101010101011d8018711c1620582c
2500c48e2100009e011d007251d01e20
6e285500c48e2100001e000000fc0054
582d53523637342020202020000000fd
00313d0f2e08000a202020202020019b
02032f724f8504030f0e07069413121e
1d1615012f097f070f1f071707503707
503f07c0834f000066030c00ffff808c
0ad08a20e02d10103e9600c48e210000
18011d80d0721c1620102c2580c48e21
00009e011d00bc52d01e20b8285540c4
8e2100001e8c0ad090204031200c4055
00c48e210000180000000000000000a8
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Tested-by: Andre Heider <a.heider@gmail.com>
Cc: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Bit a bit -fixes pull request in the merge window than usual dua to two
feauture-y things:
- Display CRCs are now enabled on all platforms, including the odd DP case
on gm45/vlv. Since this is a testing-only feature it should ever hurt,
but I figured it'll help with regression-testing -fixes. So I left it
in and didn't postpone it to 3.14.
- Display power well refactoring from Imre. Would have caused major pain
conflict with the bdw stage 1 patches if I'd postpone this to -next.
It's only an relatively small interface rework, so shouldn't cause pain.
It's also been in my tree since almost 3 weeks already.
That accounts for about two thirds of the pull, otherwise just bugfixes:
- vlv backlight fix from Jesse/Jani
- vlv vblank timestamp fix from Jesse
- improved edp detection through vbt from Ville (fixes a vlv issue)
- eDP vdd fix from Paulo
- fixes for dvo lvds on i830M
- a few smaller things all over
Note: This contains a backmerge of v3.12. Since the -internal branch
always applied on top of -nightly I need that unified base to merge bdw
patches. So you'll get a conflict with radeon connector props when pulling
this (and nouveau/master will also conflict a bit when Ben doesn't
rebase). The backmerge itself only had conflicts in drm/i915.
There's also a tiny conflict between Jani's backlight fix and your sysfs
lifetime fix in drm-next.
* tag 'drm-intel-fixes-2013-11-07' of git://people.freedesktop.org/~danvet/drm-intel: (940 commits)
drm/i915/vlv: use per-pipe backlight controls v2
drm/i915: make backlight functions take a connector
drm/i915: move opregion asle request handling to a work queue
drm/i915/vlv: use PIPE_START_VBLANK interrupts on VLV
drm/i915: Make intel_dp_is_edp() less specific
drm/i915: Give names to the VBT child device type bits
drm/i915/vlv: enable HDA display audio for Valleyview2
drm/i915/dvo: call ->mode_set callback only when the port is running
drm/i915: avoid unclaimed registers when capturing the error state
drm/i915: Enable DP port CRC for the "auto" source on g4x/vlv
drm/i915: scramble reset support for DP port CRC on vlv
drm/i915: scramble reset support for DP port CRC on g4x
drm/i916: add "auto" pipe CRC source
...
Conflicts:
MAINTAINERS
drivers/gpu/drm/i915/intel_panel.c
drivers/gpu/drm/nouveau/core/subdev/mc/base.c
drivers/gpu/drm/radeon/atombios_encoders.c
drivers/gpu/drm/radeon/radeon_connectors.c
Don't block forever if there is nothing to wait for.
Signed-off-by: Christian König <christian.koenig@amd.com>
Tested-by: Rafa? Mi?ecki <zajec5@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Let's be a bit more consistent with our error values.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Move the ktime_get() clock readouts and potential preempt_disable()
calls from drm core into kms driver to make it compatible with the
api changes in the drm core.
This should not introduce any change in functionality or behaviour
in radeon-kms, just a reshuffling of code.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
I want to merge in the new Broadwell support as a late hw enabling
pull request. But since the internal branch was based upon our
drm-intel-nightly integration branch I need to resolve all the
oustanding conflicts in drm/i915 with a backmerge to make the 60+
patches apply properly.
We'll propably have some fun because Linus will come up with a
slightly different merge solution.
Conflicts:
drivers/gpu/drm/i915/i915_dma.c
drivers/gpu/drm/i915/i915_drv.c
drivers/gpu/drm/i915/intel_crt.c
drivers/gpu/drm/i915/intel_ddi.c
drivers/gpu/drm/i915/intel_display.c
drivers/gpu/drm/i915/intel_dp.c
drivers/gpu/drm/i915/intel_drv.h
All rather simple adjacent lines changed or partial backports from
-next to -fixes, with the exception of the thaw code in i915_dma.c.
That one needed a bit of shuffling to restore the intent.
Oh and the massive header file reordering in intel_drv.h is a bit
trouble. But not much.
v2: Also don't forget the fixup for the silent conflict that results
in compile fail ...
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
PPSMC_EXTRAFLAGS_AC2DC_GPIO5_POLARITY_HIGH should be
set in extraFlags, not systemFlags.
Noticed-by: Sylvain BERTRAND <sylware@legeek.net>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
op 08-10-13 18:58, Thomas Hellstrom schreef:
> On 10/08/2013 06:47 PM, Jerome Glisse wrote:
>> On Tue, Oct 08, 2013 at 06:29:35PM +0200, Thomas Hellstrom wrote:
>>> On 10/08/2013 04:55 PM, Jerome Glisse wrote:
>>>> On Tue, Oct 08, 2013 at 04:45:18PM +0200, Christian König wrote:
>>>>> Am 08.10.2013 16:33, schrieb Jerome Glisse:
>>>>>> On Tue, Oct 08, 2013 at 04:14:40PM +0200, Maarten Lankhorst wrote:
>>>>>>> Allocate and copy all kernel memory before doing reservations. This prevents a locking
>>>>>>> inversion between mmap_sem and reservation_class, and allows us to drop the trylocking
>>>>>>> in ttm_bo_vm_fault without upsetting lockdep.
>>>>>>>
>>>>>>> Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
>>>>>> I would say NAK. Current code only allocate temporary page in AGP case.
>>>>>> So AGP case is userspace -> temp page -> cs checker -> radeon ib.
>>>>>>
>>>>>> Non AGP is directly memcpy to radeon IB.
>>>>>>
>>>>>> Your patch allocate memory memcpy userspace to it and it will then be
>>>>>> memcpy to IB. Which means you introduce an extra memcpy in the process
>>>>>> not something we want.
>>>>> Totally agree. Additional to that there is no good reason to provide
>>>>> anything else than anonymous system memory to the CS ioctl, so the
>>>>> dependency between the mmap_sem and reservations are not really
>>>>> clear to me.
>>>>>
>>>>> Christian.
>>>> I think is that in other code path you take mmap_sem first then reserve
>>>> bo. But here we reserve bo and then we take mmap_sem because of copy
>>> >from user.
>>>> Cheers,
>>>> Jerome
>>>>
>>> Actually the log message is a little confusing. I think the mmap_sem
>>> locking inversion problem is orthogonal to what's being fixed here.
>>>
>>> This patch fixes the possible recursive bo::reserve caused by
>>> malicious user-space handing a pointer to ttm memory so that the ttm
>>> fault handler is called when bos are already reserved. That may
>>> cause a (possibly interruptible) livelock.
>>>
>>> Once that is fixed, we are free to choose the mmap_sem ->
>>> bo::reserve locking order. Currently it's bo::reserve->mmap_sem(),
>>> but the hack required in the ttm fault handler is admittedly a bit
>>> ugly. The plan is to change the locking order to
>>> mmap_sem->bo::reserve
>>>
>>> I'm not sure if it applies to this particular case, but it should be
>>> possible to make sure that copy_from_user_inatomic() will always
>>> succeed, by making sure the pages are present using
>>> get_user_pages(), and release the pages after
>>> copy_from_user_inatomic() is done. That way there's no need for a
>>> double memcpy slowpath, but if the copied data is very fragmented I
>>> guess the resulting code may look ugly. The get_user_pages()
>>> function will return an error if it hits TTM pages.
>>>
>>> /Thomas
>> get_user_pages + copy_from_user_inatomic is overkill. We should just
>> do get_user_pages which fails with ttm memory and then use copy_highpage
>> helper.
>>
>> Cheers,
>> Jerome
> Yeah, it may well be that that's the preferred solution.
>
> /Thomas
>
I still disagree, and shuffled radeon_ib_get around to be called sooner.
How does the patch below look?
8<-------
Allocate and copy all kernel memory before doing reservations. This prevents a locking
inversion between mmap_sem and reservation_class, and allows us to drop the trylocking
in ttm_bo_vm_fault without upsetting lockdep.
Changes since v1:
- Kill extra memcpy for !AGP case.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Clear page tables after allocating them in case
we don't completely fill them later.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The DMA ring seems to be stable now.
v2: remove pt_ring_index as well
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Stop fiddling with jiffies, always wait for RADEON_FENCE_JIFFIES_TIMEOUT.
Consolidate the two wait sequence implementations into just one function.
Activate all waiters and remember if the reset was already done instead of
trying to reset from only one thread.
v2: clear reset flag earlier to avoid timeout in IB test
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It is said to cause hangs.
Signed-off-by: Marek Olšák <marek.olsak@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The parameter is in bytes not dwords.
Signed-off-by: Christian König <christian.koenig@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Make sure the UVD clocks are still active before sending
the destroy message, otherwise the hw might hang.
Signed-off-by: Christian König <christian.koenig@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Typo in the register offset.
Noticed-by: Sylvain BERTRAND <sylware@legeek.net>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
The buffers needs to be in little endian format.
Noticed-by: Sylvain BERTRAND <sylware@legeek.net>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
If the user has forced the state high or low, retain that preference
even when we switch power states.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=70654
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
If the thermal state is active, we are in the lowest performance level
to cool down the chip. Don't let the user force it higher.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Seems to be stable on them. There are still some issues
with the performance states staying in the highest levels
on certain cards when multiple monitors are attached, but
being that the the cards are always in their highest power
state at boot up anyway, this doesn't really change anything
and improves things in all other cases.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DPM seems to be stable on these asics and it drastically
improves performance depending on the boot clocks.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Avoids spamming the system log for chips where dpm is enabled by
default, but prints then messages when users force it on for other
asics.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Currently radeon devices are not properly shutdown during kexec. This
causes a varity of issues, e.g. dpm initialization failures.
Fix this by implementing a radeon_pci_shutdown function, that unloads
the driver cleanly.
Signed-off-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Needed by the hda driver to properly set up synchronization
on the audio side.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Needed by the hda driver to properly set up synchronization
on the audio side.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
The plain [EN|DIS]ABLE functions do the same thing and more
and aren't broken on some systems like [EN|DIS]ABLE_OUTPUT.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The plain [EN|DIS]ABLE functions do the same thing and more
and aren't broken on some systems like [EN|DIS]ABLE_OUTPUT.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
On SI asics, the SMC will automatically force the performance
level to the lowest level if there are no displays active. This
prevents automatic performance scaling on PowerXpress systems or
for offscreen rendering or compute when displays are disabled.
Going forward, it would be best to dynamically change this, but
for now leave scaling enabled.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=69395
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The rv6xx_clocks_per_unit() function pretends it can set flags in a u64
bitfield but really because "1" is an int it doesn't work for more than
32 bits. The only caller truncates the high bits away anyway. I've
just changed it to be a u32.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Uses CP DMA packet just like previous asics.
Useful for debugging and benchmarking. Uses
same packet format as prior asics.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Seems to be stable enough for the majority of users.
It can be disabled on the fly via connector attributes.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This hooks radeon up to the runtime PM system to enable
dynamic power management for secondary GPUs in switchable
and powerxpress laptops.
v2: agd5f: clean up, add module parameter
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Allows you to enable dither in the display hardware
when the monitor supports lower a lower bpc than the
current framebuffer format.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The FMT blocks control how data is sent from the backend
of the display pipe to to monitor. Proper set up of the
FMT blocks are required for 30bpp formats. Additionally,
dithering can be enabled on for better display with 18 and
24bpp displays. The exception is LVDS/eDP which atom
takes care of in the SelectCRTC_Source table. For now
just enable truncation until we test dithering more.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We use u16 for voltage values throughout the driver so switch
the table values to a u16 as well. Fixes an incompatible
cast error in ci_patch_clock_voltage_limits_with_vddc_leakage()
picked up by coverity.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Use the driver calculated CTS and N values rather than
having hardware generate them. This allows us to use
the modeline pixel clock rather than the actual pll clock
when setting up the dto for audio. Fixes problems with
audio playback rate on certain asics if the pll clock
does not match the pixel clock exactly.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
So drm was abusing device lifetimes, by having embedded device structures
in the minor and connector it meant that the lifetime of the internal drm
objects (drm_minor and drm_connector) were tied to the lifetime of the device
files in sysfs, so if something kept those files opened the current code
would kfree the objects and things would go downhill from there.
Now in reality there is no need for these lifetimes to be so intertwined,
especailly with hotplugging of devices where we wish to remove the sysfs
and userspace facing pieces before we can unwind the internal objects due
to open userspace files or mmaps, so split the objects out so the struct
device is no longer embedded and do what fbdev does and just allocate
and remove the sysfs inodes separately.
Signed-off-by: Dave Airlie <airlied@redhat.com>
In 3.12 I changed audio to be enabled by default,
but you still had to turn it on via xrandr. This
was confusing to users so change it to minic the
previous behavior:
- audio option is set to -1 (auto) by default which is
the current 3.12 behavior (audio is enabled but requires
xrandr to turn it on).
- if audio = 1, the audio is enabled without needing
to mess with xrandr (previous behavior)
- audio = 0 disables audio
It retains the new feature of allowing the user to enable
audio on the fly with xrandr, but turns audio on
automatically if radeon.audio=1 is set which is what
most users expect.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
This only seem to work for H.264 but not for VC-1 streams.
Need to investigate further why exactly.
This reverts commit 4b40e59212.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Stop leaking IB memory and scratch register space when the test fails.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
HW ACR support may have issues on some older chips, so
use SW ACR for now until we've tested further.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
CC: Rafał Miłecki <zajec5@gmail.com>
These checks should be ">=" instead of ">". j is used as an offset into
the table->mc_reg_address[] array and that has
SMC_SISLANDS_MC_REGISTER_ARRAY_SIZE (16) elements.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
It should be ">=" instead of ">" here. The table->mc_reg_address[]
array has SMC_EVERGREEN_MC_REGISTER_ARRAY_SIZE (16) elements.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
The error path does this:
for (--i; i >= 0; --i) {
which is a forever loop because "i" is unsigned.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Always use the regular UVD state for now. This fixes
a performance regression with UVD playback on certain APUs.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Use the hw generated values rather than calculating
them in the driver. There may be some older r6xx
asics where this doesn't work correctly. This remains
to be seen.
See bug:
https://bugs.freedesktop.org/show_bug.cgi?id=69675
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The drm code that calculates the 1001 clocks rounds up
rather than truncating. This allows the table to match
properly on those modes.
See bug:
https://bugs.freedesktop.org/show_bug.cgi?id=69675
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We can get the PCI vendor and device IDs via dev->pdev. So we can drop
the duplicated information.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
All drivers embed gem-objects into their own buffer objects. There is no
reason to keep drm_gem_object_alloc(), gem->driver_private and
->gem_init_object() anymore.
New drivers are highly encouraged to do the same. There is no benefit in
allocating gem-objects separately.
Cc: Dave Airlie <airlied@gmail.com>
Cc: Alex Deucher <alexdeucher@gmail.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Inki Dae <inki.dae@samsung.com>
Cc: Ben Skeggs <skeggsb@gmail.com>
Cc: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Use pcie_get_readrq() and pcie_set_readrq() functions to simplify code.
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
More radeon fixes for 3.12. Kind of all over the place: UVD, DPM,
tiling, etc.
* 'drm-fixes-3.12' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: fix hdmi audio on DCE3.0/3.1 asics
drm/radeon/cik: fix overflow in vram fetch
drm/radeon: add missing hdmi callbacks for rv6xx
drm/radeon/uvd: lower msg&fb buffer requirements on UVD3
drm/radeon: disable tests/benchmarks if accel is disabled
drm/radeon: don't set default clocks for SI when DPM is disabled
drm/radeon/dpm/ci: filter clocks based on voltage/clk dep tables
drm/radeon/dpm/si: filter clocks based on voltage/clk dep tables
drm/radeon/dpm/ni: filter clocks based on voltage/clk dep tables
drm/radeon/dpm/btc: filter clocks based on voltage/clk dep tables
drm/radeon/dpm: fetch the max clk from voltage dep tables helper
drm/radeon: fix missed variable sized access
drm/radeon: Make r100_cp_ring_info() and radeon_ring_gfx() safe (v2)
drm/radeon/cik: Add tiling mode index for 1D tiled depth/stencil surfaces
drm/radeon/cik: Fix encoding of number of banks in tiling configuration info
drm/radeon/cik: Fix printing of client name on VM protection fault
drm/radeon: additional gcc fixes for radeon_atombios.c
drm/radeon: avoid UVD corruption on AGP cards using GPU gart
Missing ULL when calculating the amount of vram
leads to an overflow when the amount of vram is >= 4G.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
When dpm was merged, I added a new asic struct for
rv6xx, but it never got properly updated when the
hdmi callbacks were added due to the two patch sets
being developed in parallel.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=69729
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Cc: stable@vger.kernel.org
Starting with UVD3 message and feedback buffers have their
own 256MB segment, so no need to force them into VRAM any more.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The tests are only usable if the acceleration engines have
been successfully initialized.
Based on an initial patch from: Alex Ivanov <gnidorah@p0n4ik.tk>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
This is a partial revert of c6cf7777a3.
We need to take into account the clk voltage dependencies of the
board. Not doing so can lead to stability issues on certain
boards if the clks exceed the levels in the dep tables.
DPM already takes that into account, so for optimal performance,
use DPM.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Filter out mclk and sclk levels higher than listed in the clk
voltage dependency tables. Supporting these clocks will require
additional driver tweaking that isn't supported yet.
See bug:
https://bugs.freedesktop.org/show_bug.cgi?id=68235
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Filter out mclk and sclk levels higher than listed in the clk
voltage dependency tables. Supporting these clocks will require
additional driver tweaking that isn't supported yet.
See bug:
https://bugs.freedesktop.org/show_bug.cgi?id=68235
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
filter out mclk and sclk levels higher than listed in the clk
voltage dependency tables. Supporting these clocks will require
additional driver tweaking that isn't supported yet.
See bug:
https://bugs.freedesktop.org/show_bug.cgi?id=68235
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Filter out mclk and sclk levels higher than listed in the clk
voltage dependency tables. Supporting these clocks will require
additional driver tweaking that isn't supported yet.
See bug:
https://bugs.freedesktop.org/show_bug.cgi?id=68235
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch adds a helper function to fetch the max clock
from the voltage clock dependecy tables. Clocks above that
level tend to be unstable and will require additional driver
tweaks in order to work properly.
This patch implemented the helper function to fetch the max clocks
from the dependency tables. The following patches implement the
per-asic clock filtering.
See bug:
https://bugs.freedesktop.org/show_bug.cgi?id=68235
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
I missed this when I fixed up this file.
Noticed-by: Mathias Fröhlich <Mathias.Froehlich@gmx.net>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Prevent NULL pointer dereference in case when radeon_ring_fini() did it's job.
Reading of r100_cp_ring_info and radeon_ring_gfx debugfs entries will lead to a KP if ring buffer was deallocated, e.g. on failed ring test.
Seen on PA-RISC machine having "radeon: ring test failed (scratch(0x8504)=0xCAFEDEAD)" issue.
v2: agd5f: add some parens around ring->ready check
Signed-off-by: Alex Ivanov <gnidorah@p0n4ik.tk>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
There are multiple valid values, not just 0 or 1. Required
to properly support 2D tiling in the userspace drivers.
Cc: stable@vger.kernel.org
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The string is encoded from the MSB to the LSB of the register.
Cc: stable@vger.kernel.org
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
If the user has forced the driver to use the internal GPU gart
rather than AGP on an AGP card, force the buffers to vram
as well.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Tested-by: Dieter Nützel <Dieter@nuetzel-hh.de>
Cc: stable@vger.kernel.org
Pull drm radeon/nouveau/core fixes from Dave Airlie:
"Mostly radeon fixes, with some nouveau bios parser, ttm fix and a fix
for AST driver"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (42 commits)
drm/fb-helper: don't sleep for screen unblank when an oops is in progress
drm, ttm Fix uninitialized warning
drm/ttm: fix the tt_populated check in ttm_tt_destroy()
drm/nouveau/ttm: prevent double-free in nouveau_sgdma_create_ttm() failure path
drm/nouveau/bios/init: fix thinko in INIT_CONFIGURE_MEM
drm/nouveau/kms: enable for non-vga pci classes
drm/nouveau/bios/init: stub opcode 0xaa
drm/radeon: avoid UVD corruptions on AGP cards
drm/radeon: fix panel scaling with eDP and LVDS bridges
drm/radeon/dpm: rework auto performance level enable
drm/radeon: Fix hmdi typo
drm/radeon/dpm/rs780: fix force_performance state for same sclks
drm/radeon/dpm/rs780: don't enable sclk scaling if not required
drm/radeon/dpm/rs780: add some sanity checking to sclk scaling
drm/radeon/dpm/rs780: use drm_mode_vrefresh()
drm/udl: rip out set_need_resched
drm/ast: fix the ast open key function
drm/radeon/dpm: add bapm callback for kb/kv
drm/radeon/dpm: add bapm callback for trinity
drm/radeon/dpm: add infrastructure to properly handle bapm
...
Putting everything into VRAM seems to help.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
We were using the wrong set_properly callback so we always
ended up with Full scaling even if something else (Center or
Full aspect) was selected.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Calling force_performance_level() from set_power_state()
doesn't work on some asics because the current power
state pointer has not been properly updated at that point.
Move the calls to force_performance_level() out of the
asic specific set_power_state() functions and into
the main power state sequence.
Fixes dpm resume on SI.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
I keep making that one, so checked if I was the only one. Apparently
not.
Cc: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
If the low and high sclks within a power state are the same,
there no need to enable sclk scaling. Enabling sclk scaling
can cause display stability issues on some boards.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
If the low and high sclks are the same, there is no need to
enable sclk scaling. This causes display stability issues on
certain boards.
Fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=60857
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Reviewed-by: Christian König <christian.koenig@amd.com>
Since the clock scaling is based on fb divider adjustments,
make sure the other pll parameters are the same.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
bapm is a pm feature for sharing the power budget between
the GPU and the CPU on APUs. It needs to be enabled or
disabled in certain circumstances. For now, disable it
when on battery and enable it when on AC power.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
bapm is a power management feature for handling the
power budget between the CPU and GPU on APUs. This
patch adds support for enabling or disabling it.
For now disable it by default. Enabling it properly
requires quite a bit more work and will be addressed
in a separate patch.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
bapm is a power management feature for handling the
power budget between the CPU and GPU on APUs. This
patch adds support for enabling or disabling it.
For now disable it by default. Enabling it properly
requires quite a bit more work and will be addressed
in a separate patch.
This patch fixes hangs on boot on certain trinity
laptops when the system is on battery power.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
The hwmon sysfs interface allows exposing temperature limits. The "max"
and "min" thresholds will be exposed as a critical high limit and its
hysteresis value, respectively. This gives the user a better idea of how
well cooling is doing and whether it is sufficient.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: David Airlie <airlied@linux.ie>
Cc: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
You can get the driver data from struct device directly, there's no
need to get the PCI device first.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: David Airlie <airlied@linux.ie>
Cc: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The OUTPUT_ENABLE action jumps past the point in the coder where
the data_offset is set on certain rs780 cards. This worked
previously because the OUTPUT_ENABLE action is always called
immediately after the ENABLE action so the data_offset remained
set. In 6f8bbaf568c7f2c497558bfd04654c0b9841ad57
(drm/radeon/atom: initialize more atom interpretor elements to 0),
we explictly reset data_offset to 0 between atom calls which then
caused this to fail. The fix is to just skip calling the
OUTPUT_ENABLE action on the problematic chipsets. The ENABLE
action does the same thing and more. Ultimately, we could
probably drop the OUTPUT_ENABLE action all together on DCE3
asics.
fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=60791
v2: only rs880 seems to be affected
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Some older 6xx-7xx boards didn't always fill in the
UVD clocks properly in the UVD power states. This
leads to the driver trying to set a 0 clock which
results in slow or broken UVD playback.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=69120
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Neither complete nor perfect, but solves my problem at hand
and might be useful in the future.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Certain r6xx boards use the same power state for both UVD
and other things. Since we don't support UVD on r6xx boards
at the moment, there was no callback installed for setting
the UVD clocks, however, on systems that use the same power
state, this leads to a NULL pointer dereference. Fill
in a stubbed out implementation for now to avoid the crash.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=66963
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: "3.11" <stable@vger.kernel.org>
This adds spinlocks to protect access to other
indirect register apertures. These indirect spaces are
used pretty infrequently and we haven't had an reported
problems, but better safe than sorry.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
smc registers are access indirectly via the main mmio aperture, so
there may be problems with concurrent access. This adds a spinlock
to protect access to this register space.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This updates dpm support for KV asics. Notably there
are some changes in acp handling and forcing performance
levels.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The problem here is that "unsigned i" is always greater than or equal to
zero. These loops mostly have a second check for "(i == 0)" so only the
last two are actually buggy. The rest is just cleanup.
Bug 1: kv_force_dpm_highest() doesn't have an "(i == 0)" check so it's
a potential forever loop.
Bug 2: In kv_get_sleep_divider_id_from_clock() there is a typo and the
test is reversed "<=" vs ">" so we never enter the loop. That means
normally we return KV_MAX_DEEPSLEEP_DIVIDER_ID (5). The return value
from here is saved in ->DeepSleepDivId and I wasn't able to determine
how that is used. This is a static checker fix and I have not tested
it.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
kfree() can accept NULL pointers so I have removed the checks. Also
I've used a pointer to shorten the lines.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This provides a connector property to enable/disable hdmi
audio on the fly. The default is disabled, but you can select
auto (let the driver detect an audio capable monitor and enable it)
or enabled (force audio enabled). This also enables audio by
default so you no longer need a module parameter to enable audio.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Make sure the audio pin is valid before accessing its members.
Noticed by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Allows you to limit the selected power levels via sysfs.
Force the feedback divider to select a power level.
v2: fix checking in rs780_force_fbdiv,
drop a duplicate divider structure in rs780_dpm_force_performance_level,
Force the voltage level too.
Signed-off-by: Anthoine Bourgeois <anthoine.bourgeois@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The internal cp interrupts need to be enabled and
disabled at specific times in order clockgating to
work properly. This patch changes the handling
of the CP_INT_CNTL register to respect the current
state of the internal CP interrupts when making
changes to the other interrupts in CP_INT_CNTL.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The internal cp interrupts need to be enabled and
disabled at specific times in order clockgating to
work properly. This patch changes the handling
of the CP_INT_CNTL register to respect the current
state of the internal CP interrupts when making
changes to the other interrupts in CP_INT_CNTL.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Pull trivial tree from Jiri Kosina:
"The usual trivial updates all over the tree -- mostly typo fixes and
documentation updates"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (52 commits)
doc: Documentation/cputopology.txt fix typo
treewide: Convert retrun typos to return
Fix comment typo for init_cma_reserved_pageblock
Documentation/trace: Correcting and extending tracepoint documentation
mm/hotplug: fix a typo in Documentation/memory-hotplug.txt
power: Documentation: Update s2ram link
doc: fix a typo in Documentation/00-INDEX
Documentation/printk-formats.txt: No casts needed for u64/s64
doc: Fix typo "is is" in Documentations
treewide: Fix printks with 0x%#
zram: doc fixes
Documentation/kmemcheck: update kmemcheck documentation
doc: documentation/hwspinlock.txt fix typo
PM / Hibernate: add section for resume options
doc: filesystems : Fix typo in Documentations/filesystems
scsi/megaraid fixed several typos in comments
ppc: init_32: Fix error typo "CONFIG_START_KERNEL"
treewide: Add __GFP_NOWARN to k.alloc calls with v.alloc fallbacks
page_isolation: Fix a comment typo in test_pages_isolated()
doc: fix a typo about irq affinity
...
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Alex Deucher <Alexander.Deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@gmail.com>
Enable support for drm render nodes for radeon by flagging the ioctls that
are safe and just needed for rendering.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Alex writes:
This is the radeon drm-next request. Big changes include:
- support for dpm on CIK parts
- support for ASPM on CIK parts
- support for berlin GPUs
- major ring handling cleanup
- remove the old 3D blit code for bo moves in favor of CP DMA or sDMA
- lots of bug fixes
[airlied: fix up a bunch of conflicts from drm_order removal]
* 'drm-next-3.12' of git://people.freedesktop.org/~agd5f/linux: (898 commits)
drm/radeon/dpm: make sure dc performance level limits are valid (CI)
drm/radeon/dpm: make sure dc performance level limits are valid (BTC-SI) (v2)
drm/radeon: gcc fixes for extended dpm tables
drm/radeon: gcc fixes for kb/kv dpm
drm/radeon: gcc fixes for ci dpm
drm/radeon: gcc fixes for si dpm
drm/radeon: gcc fixes for ni dpm
drm/radeon: gcc fixes for trinity dpm
drm/radeon: gcc fixes for sumo dpm
drm/radeonn: gcc fixes for rv7xx/eg/btc dpm
drm/radeon: gcc fixes for rv6xx dpm
drm/radeon: gcc fixes for radeon_atombios.c
drm/radeon: enable UVD interrupts on CIK
drm/radeon: fix init ordering for r600+
drm/radeon/dpm: only need to reprogram uvd if uvd pg is enabled
drm/radeon: check the return value of uvd_v1_0_start in uvd_v1_0_init
drm/radeon: split out radeon_uvd_resume from uvd_v4_2_resume
radeon kms: fix uninitialised hotplug work usage in r100_irq_process()
drm/radeon/audio: set up the sads on DCE3.2 asics
drm/radeon: fix handling of variable sized arrays for router objects
...
Conflicts:
drivers/gpu/drm/i915/i915_dma.c
drivers/gpu/drm/i915/i915_gem_dmabuf.c
drivers/gpu/drm/i915/intel_pm.c
drivers/gpu/drm/radeon/cik.c
drivers/gpu/drm/radeon/ni.c
drivers/gpu/drm/radeon/r600.c
Check to make sure the dc limits are valid before using them.
Some systems may not have a dc limits table. In that case just
use the ac limits. This fixes hangs on systems when the power
state is changed when on battery (dc) due to invalid performance
state parameters.
Should fix:
https://bugs.freedesktop.org/show_bug.cgi?id=68708
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Check to make sure the dc limits are valid before using them.
Some systems may not have a dc limits table. In that case just
use the ac limits. This fixes hangs on systems when the power
state is changed when on battery (dc) due to invalid performance
state parameters.
Should fix:
https://bugs.freedesktop.org/show_bug.cgi?id=68708
v2: fix up limits in dpm_init()
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
The same as on evergreen.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reported-by: FrankR Huang <FrankR.Huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
The vram scratch buffer needs to be initialized
before the mc is programmed otherwise we program
0 as the GPU address of the default GPU fault
page. In most cases we put vram at zero anyway and
reserve a page for the legacy vga buffer so in practice
this shouldn't cause any problems, but better to make
it correct.
Was changed in:
6fab3febf6
Reported-by: FrankR Huang <FrankR.Huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Avoid needless uvd reprogramming if uvd powergating is disabled.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
No need to try the ring tests if starting the UVD block failed.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
For powergating, we just need to re-init the registers, there
is no need to restore the uvd BOs. This just adds needless
work when powergating uvd for playback while the system is
on. We only need to restore the uvd BOs on an actual resume
from suspend or when the driver loads.
This fixes multi-stream UVD playback on KB systems.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
The table has the following format:
typedef struct _ATOM_SRC_DST_TABLE_FOR_ONE_OBJECT //usSrcDstTableOffset pointing to this structure
{
UCHAR ucNumberOfSrc;
USHORT usSrcObjectID[1];
UCHAR ucNumberOfDst;
USHORT usDstObjectID[1];
}ATOM_SRC_DST_TABLE_FOR_ONE_OBJECT;
usSrcObjectID[] and usDstObjectID[] are variably sized, so we
can't access them directly. Use pointers and update the offset
appropriately when accessing the Dst members.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Setting MC_MISC_CNTL.GART_INDEX_REG_EN causes hangs on
some boards on resume. The systems seem to work fine
without touching this bit so leave it as is.
v2: read-modify-write the GART_INDEX_REG_EN bit.
I suspect the problem is that we are losing the other
settings in the register.
fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=52952
Reported-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Daniel Tobias <dan.g.tob@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
This fills in the GPU specific details for berlin
GPU cores so that the driver will work with them.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
These blocks need to be ungated for the other parts of
the driver properly initialize them (e.g., after a gpu
reset, etc.).
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Since we aren't using it when the crtc is disabled, turn it off
to save power. The GRPH block is the part of the display
controller that controls the primary graphics plane (size,
address, etc.).
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
These fixes make writes work properly. Previously
only reads worked. Note that this feature is off
by default.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
If the LCD table contains an EDID record, properly account
for the edid size when walking through the records.
This should fix error messages about unknown LCD records.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Check the overrides in the firmware info table before
enabling spread spectrum on the engine or memory clocks.
Some boards may have valid spread spectrum tables, but
shouldn't necessarily have it enabled.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We need to allocate line buffer to each display when
setting up the watermarks. Failure to do so can lead
to a blank screen. This fixes blank screen problems
on dce8 asics.
Based on an initial fix from:
Jay Cornwall <jay.cornwall@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
We need to allocate line buffer to each display when
setting up the watermarks. Failure to do so can lead
to a blank screen. This fixes blank screen problems
on dce6 asics.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=64850
Based on an initial fix from:
Jay Cornwall <jay.cornwall@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
We need to allocate line buffer to each display when
setting up the watermarks. Failure to do so can lead
to a blank screen. This fixes blank screen problems
on dce4.1/5 asics.
Based on an initial fix from:
Jay Cornwall <jay.cornwall@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Also add a new RADEON_INFO query to check that CP DMA packets are
supported on the compute ring.
CP DMA has been supported since the 3.8 kernel, but due to an oversight
we forgot to teach the CS checker that the CP DMA packet was legal for
the compute ring on Southern Islands GPUs.
This patch fixes a bug where the radeon driver will incorrectly reject a legal
CP DMA packet from user space. I would like to have the patch
backported to stable so that we don't have to require Mesa users to use a
bleeding edge kernel in order to take advantage of this feature which
is already present in the stable kernels (3.8 and newer).
v2:
- Don't bump kms version, so this patch can be backported to stable
kernels.
Cc: stable@vger.kernel.org
Signed-off-by: Tom Stellard <thomas.stellard@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Now that the CP is no longer reset and cg is properly
disabled in when appropriate in the dpm code we can
now enable mgcg (medium grained clockgating).
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Clockgating needs to be disabled around certain parts
of dpm setup otherwise the smc gets into a bad state
and dpm doesn't work properly.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Clockgating needs to be disabled around certain parts
of dpm setup otherwise the smc gets into a bad state
and dpm doesn't work properly.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The format of the clearstate buffer used for pg (powergating)
changed between NI and SI. This formats it properly for what
the hardware expects on SI+.
v2: fix addresses
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Clockgating requires signalling between the CP and the
RLC to work properly. Resetting the CP block in the
CP resume code messed up the internal coordination
between the blocks. Removing the reset allows gfx
clockgating to work properly. However, when gfx clock
gating is enabled, there is a strange interaction with
dpm which causes the chip to stay in the high performance
level all the time, so leave gfx clockgating disabled
for now.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- use new cg/pg flags for finer grained clock and
powergating control
- restructure the cg/pg code so it can be called from
other components such as dpm
v2: fix build breakage from rebase
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The format of the clearstate buffer used for pg (powergating)
changed between NI and SI. This formats it properly for what
the hardware expects on SI.
v2: fix addresses
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Now that the CP is no longer reset and cg is properly
disabled in when appropriate in the dpm code we can
now enable mgcg (medium grained clockgating).
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Clockgating needs to be disabled around certain parts
of dpm setup otherwise the smc gets into a bad state
and dpm doesn't work properly.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Clockgating requires signalling between the CP and the
RLC to work properly. Resetting the CP block in the
CP resume code messed up the internal coordination
between the blocks. Removing the reset allows gfx
clockgating to work properly. However, when gfx clock
gating is enabled, there is a strange interaction with
dpm which causes the chip to stay in the high performance
level all the time, so leave gfx clockgating disabled
for now.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Resturcture clockgating code so that it can be
enabled/disabled from other components such as
dpm.
v2: make function static
v3: add fine grained cg controls
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This commits adds flags for supported clockgating and
powergating features. This allows us to more easily
track which features are supported on a particular
asic and to enable/disable features for debugging.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This updates the audio driver to the speaker allocation
block from the EDID. A similar change was just implemented
for DCE4-8.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This updates the audio driver to the speaker allocation
block from the EDID. A similar change was just implemented
for DCE6/8.
v2: remove unused variables
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Rafał Miłecki <zajec5@gmail.com>
Do it before enabling audio channels (in AFMT_AUDIO_PACKET_CONTROL2
register).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Similar to DCE4/5, but supports multiple audio pins
which can be assigned per afmt block.
v2: rework the driver to handle more than one audio
pin.
v3: try different dto reg
v4: properly program dto
v5 (ck): change dto programming order
v6: program speaker allocation block
v7: rebase
v8: rebase on Rafał's changes
v9: integrated Rafał's comments, update to latest
drm_edid_to_speaker_allocation API
v10: add missing line break in error message
v11: add back audio enabled messages
v12: fix copy paste typo in r600_audio_enable
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Acked-by: Rafał Miłecki <zajec5@gmail.com>
Similar to separating the UVD code, just put the DMA
functions into separate files.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Our different hardware blocks are actually completely
separated, so it doesn't make much sense any more to
structure the code by pure chipset generations.
Start restructuring the code by separating our the UVD block.
v2: updated commit message
v3: rebased and restructurized start/stop functions for kv dpm.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Now that we have callbacks for [rw]ptr handling we can
remove the special handling for the DMA rings and use
the callbacks instead.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The hardware just doesn't support this correctly.
Disable it before we accidentally write anywhere we shouldn't.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Give the ring functions a separate structure and let the asic
structure point to the ring specific functions. This simplifies
the code and allows us to make changes at only one point.
No change in functionality.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Need to swap the data fetched over i2c properly. This
is the same fix as the endian fix for aux channel
transactions.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
According to the internal teams, we never hit the limit for
mclk switching on these asics, so we can disable the check.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The LCD has a relatively short vblank time (216us), but
the card is able to reclock memory fine in that time.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reported-by: normalrawr@gmail.com
Disable the UVD block when not in use to save power.
The block is not actually powergated on CI, but we
switch between UVD DPM (where the uvd clocks are
adjusted on demand) and clocks off.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When we PG (powergate) UVD, we need to re-initialize it
before we can use it again.
v2: rebase on UVD stop fixes
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Starting on CIK, multi-media blocks like UVD no longer
have special power state. Rather they have their own
DPM implementation which adjusts their clocks dynamically
when active. When they are not active, the blocks are
powergated to save power.
v2: add missing pm locks
v3: rebase on uvd state selection rework
v4: fix inverted logic typo noticed by Christian
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Check if we can switch the mclk during the vblank time otherwise
we may get artifacts on the screen when the mclk changes.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This adds dpm support for btc asics. This includes:
- dynamic engine clock scaling
- dynamic memory clock scaling
- dynamic voltage scaling
- dynamic pcie gen switching
Set radeon.dpm=1 to enable.
v2: remove unused radeon_atombios.c changes,
make missing smc ucode non-fatal
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This adds dpm support for KB/KV asics. This includes:
- dynamic engine clock scaling
- dynamic voltage scaling
- power containment
- shader power scaling
Set radeon.dpm=1 to enable.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Internally we switched to using a separate header for
atombios pplib definitions. Switch over the open source
driver.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Calculate the low and high watermarks based on the low and high
clocks for the current power state. The dynamic pm hw will select
the appropriate watermark based on the internal dpm state.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Newer asics have a lot of vram so it's less of an
issue to waste a little more space for the gart
page table. This gives us some additional gart space
before having to migrate to non-gart system ram
for games, etc. where we use up most of vram.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
1. Handle the the thermal state directly in the work handler.
Remove the state selection function since nothing else uses it now.
2. On some asics there is no thermal state, so we just use a regular
state and force the low performance state.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Use the UVD handle information to determine which
which power states to select when using UVD. For
example, decoding a single SD stream requires much
lower clocks than multiple HD streams.
v2: switch to a cleaner dpm/uvd interface
v3: change the uvd power state while streams
are active if need be
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add a helper function for counting the number of open stream handles.
v2: fix copy-pasta in comments and whitespace error
v3: make function static since it's only used in radeon_uvd.c
at the moment
v4: make non-static again for future changes
v5: make static again for new rework of dpm uvd changes
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This lets drivers see the flags requested by the application
[airlied: fixup for rcar/imx/msm]
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Dave Airlie <airlied@gmail.com>
For optimus and powerxpress muxless we really want the GPU
driver deciding when to power up/down the GPU, not userspace.
This adds the ability for a driver to dynamically power up/down
the GPU and remove the switcheroo from controlling it, the
switcheroo reports the dynamic state to userspace also.
It also adds 2 power domains, one for machine where the power
switch is controlled outside the GPU D3 state, so the powerdown
ordering is done correctly, and the second for the hdmi audio
device to make sure it can resume for PCI config space accesses.
v1.1: fix build with switcheroo off
v2: add power domain support for radeon and v1 nvidia dsms
v2.1: fix typo in off case
v3: add audio power domain for hdmi audio + misc audio fixes
v4: use PCI_SLOT macro, drop power reference on hdmi audio resume
failure also.
Signed-off-by: Dave Airlie <airlied@redhat.com>
GEM does already a good job in tracking access to gem buffers via handles
and drm_vma access management. However, TTM drivers currently do not
verify this during mmap().
TTM provides the verify_access() callback to test this. So fix all drivers
to actually call into gem+vma to verify access instead of always returning
0.
All drivers assume that user-space can only get access to TTM buffers via
GEM handles. So whenever the verify_access() callback is called from
ttm_bo_mmap(), the buffer must have a valid embedded gem object. This is
true for all TTM+GEM drivers. But that's why this patch doesn't touch pure
TTM drivers (ie, vmwgfx).
v2: Switch to drm_vma_node_verify_access() to correctly return -EACCES if
access was denied.
Cc: Dave Airlie <airlied@redhat.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Cc: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The new arch_phys_wc_add/del functions do the right thing both with
and without MTRR support in the kernel. So we can drop these
additional checks.
David Herrmann suggest to also kill the DRIVER_USE_MTRR flag since
it's now unused, which spurred me to do a bit a better audit of the
affected drivers. David helped a lot in that. Quoting our mail
discussion:
On Wed, Jul 10, 2013 at 5:41 PM, David Herrmann <dh.herrmann@gmail.com> wrote:
> On Wed, Jul 10, 2013 at 5:22 PM, Daniel Vetter <daniel.vetter@ffwll.ch> wrote:
>> On Wed, Jul 10, 2013 at 3:51 PM, David Herrmann <dh.herrmann@gmail.com> wrote:
>>>> -#if __OS_HAS_MTRR
>>>> -static inline int drm_core_has_MTRR(struct drm_device *dev)
>>>> -{
>>>> - return drm_core_check_feature(dev, DRIVER_USE_MTRR);
>>>> -}
>>>> -#else
>>>> -#define drm_core_has_MTRR(dev) (0)
>>>> -#endif
>>>> -
>>>
>>> That was the last user of DRIVER_USE_MTRR (apart from drivers setting
>>> it in .driver_features). Any reason to keep it around?
>>
>> Yeah, I guess we could rip things out. Which will also force me to
>> properly audit drivers for the eventual behaviour change this could
>> entail (in case there's an x86 driver which did not ask for an mtrr,
>> but iirc there isn't).
>
> david@david-mb ~/dev/kernel/linux $ for i in drivers/gpu/drm/* ; do if
> test -d "$i" ; then if ! grep -q USE_MTRR -r $i ; then echo $i ; fi ;
> fi ; done
> drivers/gpu/drm/exynos
> drivers/gpu/drm/gma500
> drivers/gpu/drm/i2c
> drivers/gpu/drm/nouveau
> drivers/gpu/drm/omapdrm
> drivers/gpu/drm/qxl
> drivers/gpu/drm/rcar-du
> drivers/gpu/drm/shmobile
> drivers/gpu/drm/tilcdc
> drivers/gpu/drm/ttm
> drivers/gpu/drm/udl
> drivers/gpu/drm/vmwgfx
> david@david-mb ~/dev/kernel/linux $
>
> So for x86 gma500,nouveau,qxl,udl,vmwgfx don't set DRIVER_USE_MTRR.
> But I cannot tell whether they break if we call arch_phys_wc_add/del,
> anyway. At least nouveau seemed to work here, but it doesn't use AGP
> or drm_bufs, I guess.
Cool, thanks a lot for stitching together the list of drivers to look
at. So for real KMS drivers it's the drives responsibility to add an
mtrr if it needs one. nouvea, radeon, mgag200, i915 and vmwgfx do that
already. Somehow the savage driver also ends up doing that, I have no
idea why.
Note that gma500 as a pure KMS driver doesn't need MTRR setup since
the platforms that it supports all support PAT. So no MTRRs needed to
get wc iomappings.
The mtrr support in the drm core is all for legacy mappings of garts,
framebuffers and registers. All legacy drivers set the USE_MTRR flag,
so we're good there.
All in all I think we can really just ditch this
/endquote
v2: Also kill DRIVER_USE_MTRR as suggested by David Herrmann
v3: Rebase on top of David Herrmann's agp setup/cleanup changes.
Cc: David Herrmann <dh.herrmann@gmail.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Andy Lutomirski <luto@amacapital.net>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
So I've stumbled over drm_fasync and wondered what it does. Digging
that up is quite a story.
First I've had to read up on what this does and ended up being rather
bewildered why peopled loved signals so much back in the days that
they've created SIGIO just for that ...
Then I wondered how this ever works, and what that strange "No-op."
comment right above it should mean. After all calling the core fasync
helper is pretty obviously not a noop. After reading through the
kernels FASYNC implementation I've noticed that signals are only sent
out to the processes attached with FASYNC by calling kill_fasync.
No merged drm driver has ever done that.
After more digging I've found out that the only driver that ever used
this is the so called GAMMA driver. I've frankly never heard of such a
gpu brand ever before. Now FASYNC seems to not have been the only bad
thing with that driver, since Dave Airlie removed it from the drm
driver with prejudice:
commit 1430163b4bbf7b00367ea1066c1c5fe85dbeefed
Author: Dave Airlie <airlied@linux.ie>
Date: Sun Aug 29 12:04:35 2004 +0000
Drop GAMMA DRM from a great height ...
Long story short, the drm fasync support seems to be doing absolutely
nothing. And the only user of it was never merged into the upstream
kernel. And we don't need any fops->fasync callback since the fcntl
implementation in the kernel already implements the noop case
correctly.
So stop this particular cargo-cult and rip it all out.
v2: Kill drm_fasync assignments in rcar (newly added) and imx drivers
(somehow I've missed that one in staging). Also drop the reference in
the drm DocBook. ARM compile-fail reported by Rob Clark.
v3: Move the removal of dev->buf_asnyc assignment in drm_setup to this
patch here.
v4: Actually git add ... tsk.
Cc: Dave Airlie <airlied@linux.ie>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Rob Clark <robdclark@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Again, it does nothing.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Alex Deucher