* 'usb-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (144 commits)
USB: add support for Dream Cheeky DL100B Webmail Notifier (1d34:0004)
USB: serial: ftdi_sio: add support for TIOCSERGETLSR
USB: ehci-mxc: Setup portsc register prior to accessing OTG viewport
USB: atmel_usba_udc: fix freeing irq in usba_udc_remove()
usb: ehci-omap: fix tll channel enable mask
usb: ohci-omap3: fix trivial typo
USB: gadget: ci13xxx: don't assume that PAGE_SIZE is 4096
USB: gadget: ci13xxx: fix complete() callback for no_interrupt rq's
USB: gadget: update ci13xxx to work with g_ether
USB: gadgets: ci13xxx: fix probing of compiled-in gadget drivers
Revert "USB: musb: pm: don't rely fully on clock support"
Revert "USB: musb: blackfin: pm: make it work"
USB: uas: Use GFP_NOIO instead of GFP_KERNEL in I/O submission path
USB: uas: Ensure we only bind to a UAS interface
USB: uas: Rename sense pipe and sense urb to status pipe and status urb
USB: uas: Use kzalloc instead of kmalloc
USB: uas: Fix up the Sense IU
usb: musb: core: kill unneeded #include's
DA8xx: assign name to MUSB IRQ resource
usb: gadget: g_ncm added
...
Manually fix up trivial conflicts in USB Kconfig changes in:
arch/arm/mach-omap2/Kconfig
arch/sh/Kconfig
drivers/usb/Kconfig
drivers/usb/host/ehci-hcd.c
and annoying chip clock data conflicts in:
arch/arm/mach-omap2/clock3xxx_data.c
arch/arm/mach-omap2/clock44xx_data.c
i2400m implements dynamic work allocation and queueing mechanism in
i2400_schedule_work(); however, this is only used for reset and
recovery which can be served equally well with preallocated per device
works.
Replace i2400m_schedule_work() with two work structs in struct i2400m.
These works are explicitly canceled when the device is released making
calls to flush_scheduled_work(), which is being deprecated,
unnecessary.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Cc: linux-wimax@intel.com
Cc: netdev@vger.kernel.org
This patch (as1436) takes care of leftover references to
udev->autosuspend_delay that didn't get removed during the earlier
conversion to the runtime-PM autosuspend API.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1699 commits)
bnx2/bnx2x: Unsupported Ethtool operations should return -EINVAL.
vlan: Calling vlan_hwaccel_do_receive() is always valid.
tproxy: use the interface primary IP address as a default value for --on-ip
tproxy: added IPv6 support to the socket match
cxgb3: function namespace cleanup
tproxy: added IPv6 support to the TPROXY target
tproxy: added IPv6 socket lookup function to nf_tproxy_core
be2net: Changes to use only priority codes allowed by f/w
tproxy: allow non-local binds of IPv6 sockets if IP_TRANSPARENT is enabled
tproxy: added tproxy sockopt interface in the IPV6 layer
tproxy: added udp6_lib_lookup function
tproxy: added const specifiers to udp lookup functions
tproxy: split off ipv6 defragmentation to a separate module
l2tp: small cleanup
nf_nat: restrict ICMP translation for embedded header
can: mcp251x: fix generation of error frames
can: mcp251x: fix endless loop in interrupt handler if CANINTF_MERRF is set
can-raw: add msg_flags to distinguish local traffic
9p: client code cleanup
rds: make local functions/variables static
...
Fix up conflicts in net/core/dev.c, drivers/net/pcmcia/smc91c92_cs.c and
drivers/net/wireless/ath/ath9k/debug.c as per David
* 'llseek' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/bkl:
vfs: make no_llseek the default
vfs: don't use BKL in default_llseek
llseek: automatically add .llseek fop
libfs: use generic_file_llseek for simple_attr
mac80211: disallow seeks in minstrel debug code
lirc: make chardev nonseekable
viotape: use noop_llseek
raw: use explicit llseek file operations
ibmasmfs: use generic_file_llseek
spufs: use llseek in all file operations
arm/omap: use generic_file_llseek in iommu_debug
lkdtm: use generic_file_llseek in debugfs
net/wireless: use generic_file_llseek in debugfs
drm: use noop_llseek
All file_operations should get a .llseek operation so we can make
nonseekable_open the default for future file operations without a
.llseek pointer.
The three cases that we can automatically detect are no_llseek, seq_lseek
and default_llseek. For cases where we can we can automatically prove that
the file offset is always ignored, we use noop_llseek, which maintains
the current behavior of not returning an error from a seek.
New drivers should normally not use noop_llseek but instead use no_llseek
and call nonseekable_open at open time. Existing drivers can be converted
to do the same when the maintainer knows for certain that no user code
relies on calling seek on the device file.
The generated code is often incorrectly indented and right now contains
comments that clarify for each added line why a specific variant was
chosen. In the version that gets submitted upstream, the comments will
be gone and I will manually fix the indentation, because there does not
seem to be a way to do that using coccinelle.
Some amount of new code is currently sitting in linux-next that should get
the same modifications, which I will do at the end of the merge window.
Many thanks to Julia Lawall for helping me learn to write a semantic
patch that does all this.
===== begin semantic patch =====
// This adds an llseek= method to all file operations,
// as a preparation for making no_llseek the default.
//
// The rules are
// - use no_llseek explicitly if we do nonseekable_open
// - use seq_lseek for sequential files
// - use default_llseek if we know we access f_pos
// - use noop_llseek if we know we don't access f_pos,
// but we still want to allow users to call lseek
//
@ open1 exists @
identifier nested_open;
@@
nested_open(...)
{
<+...
nonseekable_open(...)
...+>
}
@ open exists@
identifier open_f;
identifier i, f;
identifier open1.nested_open;
@@
int open_f(struct inode *i, struct file *f)
{
<+...
(
nonseekable_open(...)
|
nested_open(...)
)
...+>
}
@ read disable optional_qualifier exists @
identifier read_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
expression E;
identifier func;
@@
ssize_t read_f(struct file *f, char *p, size_t s, loff_t *off)
{
<+...
(
*off = E
|
*off += E
|
func(..., off, ...)
|
E = *off
)
...+>
}
@ read_no_fpos disable optional_qualifier exists @
identifier read_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
@@
ssize_t read_f(struct file *f, char *p, size_t s, loff_t *off)
{
... when != off
}
@ write @
identifier write_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
expression E;
identifier func;
@@
ssize_t write_f(struct file *f, const char *p, size_t s, loff_t *off)
{
<+...
(
*off = E
|
*off += E
|
func(..., off, ...)
|
E = *off
)
...+>
}
@ write_no_fpos @
identifier write_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
@@
ssize_t write_f(struct file *f, const char *p, size_t s, loff_t *off)
{
... when != off
}
@ fops0 @
identifier fops;
@@
struct file_operations fops = {
...
};
@ has_llseek depends on fops0 @
identifier fops0.fops;
identifier llseek_f;
@@
struct file_operations fops = {
...
.llseek = llseek_f,
...
};
@ has_read depends on fops0 @
identifier fops0.fops;
identifier read_f;
@@
struct file_operations fops = {
...
.read = read_f,
...
};
@ has_write depends on fops0 @
identifier fops0.fops;
identifier write_f;
@@
struct file_operations fops = {
...
.write = write_f,
...
};
@ has_open depends on fops0 @
identifier fops0.fops;
identifier open_f;
@@
struct file_operations fops = {
...
.open = open_f,
...
};
// use no_llseek if we call nonseekable_open
////////////////////////////////////////////
@ nonseekable1 depends on !has_llseek && has_open @
identifier fops0.fops;
identifier nso ~= "nonseekable_open";
@@
struct file_operations fops = {
... .open = nso, ...
+.llseek = no_llseek, /* nonseekable */
};
@ nonseekable2 depends on !has_llseek @
identifier fops0.fops;
identifier open.open_f;
@@
struct file_operations fops = {
... .open = open_f, ...
+.llseek = no_llseek, /* open uses nonseekable */
};
// use seq_lseek for sequential files
/////////////////////////////////////
@ seq depends on !has_llseek @
identifier fops0.fops;
identifier sr ~= "seq_read";
@@
struct file_operations fops = {
... .read = sr, ...
+.llseek = seq_lseek, /* we have seq_read */
};
// use default_llseek if there is a readdir
///////////////////////////////////////////
@ fops1 depends on !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier readdir_e;
@@
// any other fop is used that changes pos
struct file_operations fops = {
... .readdir = readdir_e, ...
+.llseek = default_llseek, /* readdir is present */
};
// use default_llseek if at least one of read/write touches f_pos
/////////////////////////////////////////////////////////////////
@ fops2 depends on !fops1 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read.read_f;
@@
// read fops use offset
struct file_operations fops = {
... .read = read_f, ...
+.llseek = default_llseek, /* read accesses f_pos */
};
@ fops3 depends on !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier write.write_f;
@@
// write fops use offset
struct file_operations fops = {
... .write = write_f, ...
+ .llseek = default_llseek, /* write accesses f_pos */
};
// Use noop_llseek if neither read nor write accesses f_pos
///////////////////////////////////////////////////////////
@ fops4 depends on !fops1 && !fops2 && !fops3 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read_no_fpos.read_f;
identifier write_no_fpos.write_f;
@@
// write fops use offset
struct file_operations fops = {
...
.write = write_f,
.read = read_f,
...
+.llseek = noop_llseek, /* read and write both use no f_pos */
};
@ depends on has_write && !has_read && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier write_no_fpos.write_f;
@@
struct file_operations fops = {
... .write = write_f, ...
+.llseek = noop_llseek, /* write uses no f_pos */
};
@ depends on has_read && !has_write && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read_no_fpos.read_f;
@@
struct file_operations fops = {
... .read = read_f, ...
+.llseek = noop_llseek, /* read uses no f_pos */
};
@ depends on !has_read && !has_write && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
@@
struct file_operations fops = {
...
+.llseek = noop_llseek, /* no read or write fn */
};
===== End semantic patch =====
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Julia Lawall <julia@diku.dk>
Cc: Christoph Hellwig <hch@infradead.org>
Stanse found that i2400m_rx frees skb, but still uses skb->len even
though it has skb_len defined. So use skb_len properly in the code.
And also define it unsinged int rather than size_t to solve
compilation warnings.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Cc: linux-wimax@intel.com
Acked-by: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make wimax variables and functions local if possible.
Compile tested only.
This also removes a couple of unused EXPORT_SYMBOL.
If this breaks some out of tree code, please fix that
by putting the code in the kernel tree.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
i2400m_fw_hdr_check() was accessing hardware field
bcf_hdr->module_type (little endian 32) without converting to host
byte sex.
Reported-by: Данилин Михаил <mdanilin@nsg.net.ru>
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
cleanup patch.
Use new __packed annotation in drivers/net/
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch (as1373) fixes a couple of drivers outside the USB
subtree. Devices are now disabled or enabled for autosuspend by
calling a core function instead of setting a flag.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The i2400m->rx_roq data structure is protected against race conditions
with a reference count (i2400m->rx_roq_refcount); the pointer can be
read-referenced under the i2400m->rx_lock spinlock.
The code in i2400m_rx_edata() wasn't properly following access
protocol, performing an invalid check on i2400m->rx_roq (which is
cleared to NULL when the refcount drops to zero). As such, it was
missing to detect when the data structure is no longer valid and
oopsing with a NULL pointer dereference.
This commit fixes said check by verifying, under the rx_lock spinlock,
that i2400m->rx_roq is non-NULL and then increasing the reference
count before dropping the spinlock.
Signed-off-by: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
switch and while statements don't need semicolons at end of statement
[ Fixup minor conflicts with recent wimax merge... -DaveM ]
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes from drivers/net/ all the unnecessary
return; statements that precede the last closing brace of
void functions.
It does not remove the returns that are immediately
preceded by a label as gcc doesn't like that.
It also does not remove null void functions with return.
Done via:
$ grep -rP --include=*.[ch] -l "return;\n}" net/ | \
xargs perl -i -e 'local $/ ; while (<>) { s/\n[ \t\n]+return;\n}/\n}/g; print; }'
with some cleanups by hand.
Compile tested x86 allmodconfig only.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Updates the i2400m driver to default to firmware versions v1.5 for the
Intel Wireless WiMAX Connection 5150 and 5350 devices.
Firmware available in linux-firmware.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
This patch moves the module parameters to the file where they
can be avoided to be global and allow them to be static.
The module param : idle_mode_disabled and power_save_disabled
are moved from driver.c to control.c. Also these module parameters
are declared to be static as they are not required to be global anymore.
The module param : rx_reorder_disabled is moved from driver.c file to
rx.c file. Also this parameter is declated as static as it is not
required to be global anymore.
Signed-off-by: Prasanna S Panchamukhi<prasannax.s.panchamukhi@intel.com>
wimax_msg_alloc() returns an ERR_PTR and not null. I changed it to test
for ERR_PTR instead of null. I also added a check in front of the
kfree() because kfree() can handle null but not ERR_PTR.
Signed-off-by: Dan Carpenter <error27@gmail.com>
This patch specifies the TX queue's buffer room required by the
USB bus driver while allocating header space for a new message.
Please refer the documentation in the code.
Signed-off-by: Prasanna S. Panchamukhi <prasannax.s.panchamukhi@intel.com>
This patch specifies the TX queue's minimum buffer room required to
accommodate one smallest SDIO payload.
Please refer the documentation in the code.
Signed-off-by: Prasanna S. Panchamukhi <prasannax.s.panchamukhi@intel.com>
Increase the possibilities of including at least one payload by reserving
some additional space in the TX queue while allocating TX queue's space
for new message header. Please refer the documentation in the code for details.
Signed-off-by: Prasanna S. Panchamukhi <prasannax.s.panchamukhi@intel.com>
According to Intel Wimax i3200, i5x50 and i6x60 device specification documents,
the host driver must not reset the device if the normalized sequence numbers
are greater than 1023 for type 2 and type 3 RX messages.
This patch removes the code that incorrectly used to reset the device.
Signed-off-by: Prasanna S. Panchamukhi <prasannax.s.panchamukhi@intel.com>
This patch fixes the race condition when one thread tries to destroy
the memory allocated for rx_roq, while another thread still happen
to access rx_roq.
Such a race condition occurs when i2400m-sdio kernel module gets
unloaded, destroying the memory allocated for rx_roq while rx_roq
is accessed by i2400m_rx_edata(), as explained below:
$thread1 $thread2
$ void i2400m_rx_edata() $
$Access rx_roq[] $
$roq = &i2400m->rx_roq[ro_cin] $
$ i2400m_roq_[reset/queue/update_ws] $
$ $ void i2400m_rx_release();
$ $kfree(rx->roq);
$ $rx->roq = NULL;
$Oops! rx_roq is NULL
This patch fixes the race condition using refcount approach.
Signed-off-by: Prasanna S. Panchamukhi <prasannax.s.panchamukhi@intel.com>
This patch increases the tx_queue_len to 20 so as to
minimize the jitter in the throughput.
Signed-off-by: Prasanna S. Panchamukhi <prasannax.s.panchamukhi@intel.com>
This patch fixes an infinite loop caused by i2400m_tx_fifo_push() due
to a corner case where there is no tail space in the TX FIFO.
Please refer the documentation in the code for details.
Signed-off-by: Prasanna S. Panchamukhi <prasannax.s.panchamukhi@intel.com>
This fixes i2400m_tx_fifo_push(); the check for having enough
space in the TX FIFO's tail was obscure and broken in certain
corner cases. The new check works in all cases and is way
clearer. Please refer the documentation in the code for details.
Signed-off-by: Prasanna S. Panchamukhi <prasannax.s.panchamukhi@intel.com>
The older method of computing the maximum PDU size relied
on a method that doesn't work when we prop the maximum
number of payloads up to the physical limit, and thus we kill
the whole computation and just verify that the constants are
congruent.
Signed-off-by: Prasanna S. Panchamukhi <prasannax.s.panchamukhi@intel.com>
According to Intel Wimax i3200, i5x50 and i6x50 specification
documents, the maximum size of each TX message can be upto 16KiB.
This patch modifies the i2400m_tx() routine to check that the
message size does not exceed the 16KiB limit.
Please refer the documentation in the code for details.
Signed-off-by: Prasanna S. Panchamukhi <prasannax.s.panchamukhi@intel.com>
According to Intel Wimax i3200, i5x50 and i6x50 device specification
documents, the maximum number of payloads per message can be up to 60.
Increasing the number of payloads to 60 per message helps to
accommodate smaller payloads in a single transaction. This patch
increases the maximum number of payloads from 12 to 60 per message.
Signed-off-by: Prasanna S. Panchamukhi <prasannax.s.panchamukhi@intel.com>
This patch makes sure whenever tx_setup() is invoked during driver
initialization or device reset where TX FIFO is released and re-allocated,
the indices tx_in, tx_out, tx_msg_size, tx_sequence, tx_msg are properly
initialized.
When a device reset happens and the TX FIFO is released/re-allocated,
a new block of memory may be allocated for the TX FIFO, therefore tx_msg
should be cleared so that no any TX threads (tx_worker, tx) would access
to the out-of-date addresses.
Also, the TX threads use tx_in and tx_out to decide where to put the new
host-to-device messages and from where to copy them to the device HW FIFO,
these indices have to be cleared so after the TX FIFO is re-allocated during
the reset, the indices both refer to the head of the FIFO, ie. a new start.
The same rational applies to tx_msg_size and tx_sequence.
To protect the indices from being accessed by multiple threads simultaneously,
the lock tx_lock has to be obtained before the initializations and released
afterwards.
Signed-off-by: Cindy H Kao <cindy.h.kao@intel.com>
When bus_setup fails in i2400m_post_reset(), it falls to the error path handler
"error_bus_setup:" which includes unlock the mutext. However, we didn't ever
try to the obtain the lock when running bus_setup.
The patch is to fix the misplaced error path handler "error_bus_setup:".
Signed-off-by: Cindy H Kao <cindy.h.kao@intel.com>
This patch adds an error recovery mechanism on TX path.
The intention is to bring back the device to some known state
whenever TX sees -110 (-ETIMEOUT) on copying the data to the HW FIFO.
The TX failure could mean a device bus stuck or function stuck, so
the current error recovery implementation is to trigger a bus reset
and expect this can bring back the device.
Since the TX work is done in a thread context, there may be a queue of TX works
already that all hit the -ETIMEOUT error condition because the device has
somewhat stuck already. We don't want any consecutive bus resets simply because
multiple TX works in the queue all hit the same device erratum, the flag
"error_recovery" is introduced to denote if we are ready for taking any
error recovery. See @error_recovery doc in i2400m.h.
Signed-off-by: Cindy H Kao <cindy.h.kao@intel.com>
The problem is only seen on SDIO interface since on USB, a bus reset would
really re-probe the driver, but on SDIO interface, a bus reset will not
re-enumerate the SDIO bus, so no driver re-probe is happening. Therefore,
on SDIO interface, the reset event should be still detected and handled by
dev_reset_handle().
Problem description:
Whenever a reboot barker is received during operational mode (i2400m->boot_mode == 0),
dev_reset_handle() is invoked to handle that function reset event.
dev_reset_handle() then sets the flag i2400m->boot_mode to 1 indicating the device is
back to bootmode before proceeding to dev_stop() and dev_start().
If dev_start() returns failure, a bus reset is triggered by dev_reset_handle().
The flag i2400m->boot_mode then remains 1 when the second reboot barker arrives.
However the interrupt service routine i2400ms_rx() instead of invoking dev_reset_handle()
to handle that reset event, it filters out that boot event to bootmode because it sees
the flag i2400m->boot_mode equal to 1.
The fix:
Maintain the flag i2400m->boot_mode within dev_reset_handle() and set the flag
i2400m->boot_mode to 1 when entering dev_reset_handle(). It remains 1
until the dev_reset_handle() issues a bus reset. ie: the bus reset is
taking place just like it happens for the first time during operational mode.
To denote the actual device state and the state we expect, a flag i2400m->alive
is introduced in addition to the existing flag i2400m->updown.
It's maintained with the same way for i2400m->updown but instead of reflecting
the actual state like i2400m->updown does, i2400m->alive maintains the state
we expect. i2400m->alive is set 1 just like whenever i2400m->updown is set 1.
Yet i2400m->alive remains 1 since we expect the device to be up all the time
until the driver is removed. See the doc for @alive in i2400m.h.
An enumeration I2400M_BUS_RESET_RETRIES is added to define the maximum number of
bus resets that a device reboot can retry.
A counter i2400m->bus_reset_retries is added to track how many bus resets
have been retried in one device reboot. If I2400M_BUS_RESET_RETRIES bus resets
were retried in this boot, we give up any further retrying so the device would enter
low power state. The counter i2400m->bus_reset_retries is incremented whenever
dev_reset_handle() is issuing a bus reset and is cleared to 0 when dev_start() is
successfully done, ie: a successful reboot.
Signed-off-by: Cindy H Kao <cindy.h.kao@intel.com>
Lucas De Marchi