The GPIO settings for quadHD boards are wrong. Fix them.
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
A possible hardware bug was discovered when using CA addon hardware
attached to the ngene hardware, in that the TS input buffer much likely
will shift and thus become unaligned to 188 byte blocks (a full TS frame)
when things like CA module initialisation (which happens via differing
communication paths) take place. This causes the TS NULL removal in
tsin_exchange() to fail to detect this previously inserted data and thus
causes userspace applications to receive data they didn't sent beforehand
and ultimately cause troubles.
On driver load with an inserted CAM, buffers are fine at first (note that
the driver has to keep the communication running from/to the card by
inserting TS NULL frames, this is done in tsout_exchange() via
FillTSBuffer() - that data is simply sent back by the hardware):
offset | 0 1 2 3 4 5 .... 188 189 190 191 192 193 .... 376
data | 47 1f ff 10 6f 6f .... 47 1f ff 10 6f 6f .... 47
After a few seconds, the CA module is recognised and initialised, which is
signalled by
dvb_ca_en50221: dvb_ca adapter X: DVB CAM detected and initialised successfully
This is where the first shift happens (this is always four bytes), buffer
becomes like this:
offset | 0 1 2 3 4 5 .... 188 189 190 191 192 193 .... 376
data | 6f 6f 6f 6f 47 1f .... 6f 6f 6f 6f 47 1f .... 6f
Next, VDR, TVHeadend or any other CI aware application is started, buffers
will shift by even more bytes. It is believed this is due to the hardware
not handling control and data bytes properly distinct, and control data
having an influence on the actual data stream, which we cannot properly
detect at the driver level.
Workaround this hardware quirk by adding a detection for the TS sync byte
0x47 before each TS frame copy, scan for a new SYNC byte and a TS NULL
packet if buffers become unaligned, take note of that offset and apply
that when copying data to the DVB ring buffers. The last <188 bytes from
the hardware buffers are stored in a temp buffer (tsin_buffer), for which
the remainder will be in the beginning of the next hardware buffer (next
iteration of tsin_exchange()). That remainder will be appended to the
temp buffer and finally sent to the DVB ring buffer. The resulting TS
stream is perfectly fine, and the TS NULL packets inserted by the driver
which are sent back are properly removed. The resulting offset is being
clamped to 188 byte segments (one TS packet). Though this can result in
a repeated TS packet if the overall offset grows beyond this (and it
will grow only on CA initialisation), this is still way better than
unaligned TS frames and data sent to userspace that just isn't supposed
to be there.
This compensation can be toggled by the ci_tsfix modparam, which defaults
to 1 (enabled). In the case of problems, this can be turned off by setting
the parameter to 0 to restore the old behaviour.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Move the copy logic that will skip previously inserted TS NULL frames when
moving data to the DVB ring buffers into an own function. This is done to
not duplicate code all over the place with the following TS offset shift
fixup patch.
While we're touching this part of the code, get rid of the DEBUG_CI_XFER
debug-ifdeffery. This could be toggleable either by a Kconfig or a module
param, but in the end this will accidentally be enabled and cause lots
of kernel log messages, and such devel debug shouldn't be there anyway.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Report I2C_FUNC_I2C in .functionality() as well. The I2C interface can
handle this fine and even is required for all I2C client drivers that
utilise the regmap API which are used from within the ngene driver.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Jasmin Jessich <jasmin@anw.at>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Change the way the cxd2099 hardware is being attached to the new I2C
client interface way.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Jasmin Jessich <jasmin@anw.at>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Implement the poll callback for the dvbdev_ci file ops. The ts_poll()
function queries the DVB ring buffers for available data and space, and
reports this as appropriate. Also, set the dvb_device readers, writers
and users to proper values (one reader, one writer, two users).
This fixes the raw CI TS transport in conjunction with TVheadend's
DDCI functionality.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When probing the I2C busses in cineS2_probe(), it's no error when there's
no hardware connected to the probed expansion connector, so print this
informal message with info severity.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Currently, if there's no CXD2099AR attached to any expansion connector of
the ngene hardware, it will complain with this on every module load:
cxd2099 1-0040: No CXD2099AR detected at 0x40
cxd2099: probe of 1-0040 failed with error -5
ngene 0000:02:00.0: CXD2099AR attach failed
This happens due to the logic assuming such hardware is always there and
blindly tries to attach the cxd2099 I2C driver. Rather add a probe
function (in ngene-cards.c with a prototype in ngene.h) to check for
the existence of such hardware before probing, and don't try further if
no CXD2099 was found.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The I2C adapter evaluation (based on chan->number) is duplicated at
several places (tuner_attach_() functions, demod_attach_stv0900() and
cineS2_probe()). Clean this up by wrapping that construct in a separate
function which all users of that can pass the ngene_channel pointer and
get the correct I2C adapter from.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add support for the STV0910/STV6111/LNBH25 based DuoFlex S2 V4 DVB-S2
addon modules by recognizing them from their XO2 type value and using
the auxiliary stv0910, stv6111 and lnbh25 driver to form a complete
DVB frontend.
This also adds autoselection (if MEDIA_SUBDRV_AUTOSELECT) of the STV0910,
STV6111 and LNBH25 demod/tuner/LNB-IC drivers to Kconfig.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Recognize (probe) and support (attach) all Sony CXD28xx based DuoFlex
addon modules/cards, namely the DuoFlex CT2 (CXD2837), ISDB-T (CXD2838),
C2T2 (CXD2843) and C2T2I (CXD2854). Since all these modules are equipped
with a MachXO2 interface, that support is required for the hardware to
work. This functionality utilises the auxiliary cxd2841er and tda18212
drivers.
This also adds autoselection (if MEDIA_SUBDRV_AUTOSELECT) of the CXD2841ER
demod driver to Kconfig. The __maybe_unused annotation can now be removed
from the xo2names array.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Detect and initialise modules equipped with XO2 interfaces (Lattice
MachXO2). This requires a few more I2C transfer functions which this adds
as well. Defines for the different possible (available) module types are
added to ngene.h. The support for the actual tuners contained on these
addon modules is kept separate from this commit and is being added with
the next commits.
The xo2names array is temporarily marked __maybe_unused to silence a
corresponding compiler warning at this stage.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add support for STV0367+TDA18212 based DuoFlex CT addon modules. For this,
add a demod probe function and all necessary demod/tuner attach functions
which use existing auxiliary drivers (stv0367 and tda18212) to support
this hardware. As tda18212 is an I2C client driver, proper cleanup code
is added to the deregistration sequence in ngene-core. To not cause use-
after-free situations when there's a CXD2099 I2C client connected, which
is rather freed in ngene-core.c:cxd_detach(), add i2c_client_fe to struct
ngene_channel to keep track if the i2c_client was allocated by a frontend
driver, rather than the CI code paths. Also move the I2C access functions
to the top of the file and add the required read_regs() function for the
tda18212 ping to work.
This adds autoselection (if MEDIA_SUBDRV_AUTOSELECT) of the STV0367 demod
driver and TDA18212 tuner driver to Kconfig aswell.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Make it more clear which demod_type is used for which hardware by having
defines for the possible demod_type values. With that, change the
demod_type evaluation in tuner_attach_probe() to a switch-case instead
of an if() for each possible value.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Convert all printk() and pr_*() kernel log printing to rather use the
dev_*() macros. Not only is it discouraged to use printk() (checkpatch
even complains about that), but also this helps identifying the exact PCI
device for any printed event, and it makes almost all printing shorter
in terms of code style since there's no need to use KERN_* DEVICE_NAME
any more (dev_*() will take care of this).
Since the dprintk macro define isn't used anymore, remove it.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add two more device IDs for cards supported by the ngene driver.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
According to the TODO file, this driver only landed in staging because of
the way device nodes and data transfers are handled. Besides that this way
(use of secX devices) has become sort of standard to date (ie. VDR
supports this literally since ages via the ddci plugin, TVHeadend received
this functionality lately, and minisatip being currently worked on
regarding this), most importantly this I2C client only driver isn't even
responsible for setting up device nodes, not for handling data
transfer and so on, but only serves as interface for the dvb_ca_en50221
subsystem, just like every other DVB card out in the wild, with hard-wired
or such flexible CA interfaces. And, it would even work with cards having
the cxd2099 controller hard-wired.
Also, this driver received quite some love and even is a proper I2C client
driver by now. So, as this driver acts as a EN50221 frontend device, move
it to dvb-frontends. There is no need to keep it buried in staging.
This commit also updates all affected Kconfig and Makefile's, and adds
MEDIA_AUTOSELECT depends to ddbridge and ngene.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Jasmin Jessich <jasmin@anw.at>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Change the way the cxd2099 hardware is being attached to the new I2C
client interface way.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Jasmin Jessich <jasmin@anw.at>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Deduplicate the checks for a valid ptr in port->en, and also handle the
default case to also catch eventually yet unsupported CI hardware.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Thoses files are unused since commit b3b961448f ("V4L/DVB (13795): [Mantis/Hopper] Code overhaul, add Hopper devices into the PCI ID list")
8 year after, we could remove it.
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add new QuadHD digital only PCIe boards to driver list.
Differentiate them from 888 digital/analog QuadHD models.
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add new PCIe DVB-S/S2.
A single port Hauppauge HVR-5525
cx23885 + a8293 + m88rs6000t
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add ID of new card revision to driver list
Analog PAL/NTSC capture.
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There is a typo at the several s5h14*.h headers: continuous were
spelled incorrectly.
Fix it with this script:
for i in $(git grep -l S5H1409_MPEGTIMING_CONTINOUS_NONINVERTING_CLOCK); do
sed s,S5H1409_MPEGTIMING_CONTINOUS_NONINVERTING_CLOCK,S5H1409_MPEGTIMING_CONTINUOUS_NONINVERTING_CLOCK,g -i $i
done
for i in $(git grep -l -i continous drivers/media); do sed s,CONTINOUS,CONTINUOUS,g -i $i; done
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
* commit 'v4.16-rc4~0': (900 commits)
Linux 4.16-rc4
memremap: fix softlockup reports at teardown
libnvdimm: re-enable deep flush for pmem devices via fsync()
MAINTAINERS: take over Kconfig maintainership
vfio: disable filesystem-dax page pinning
kconfig: fix line number in recursive inclusion error message
Coccinelle: memdup: Fix typo in warning messages
i2c: octeon: Prevent error message on bus error
parisc: Reduce irq overhead when run in qemu
parisc: Use cr16 interval timers unconditionally on qemu
parisc: Check if secondary CPUs want own PDC calls
parisc: Hide virtual kernel memory layout
parisc: Fix ordering of cache and TLB flushes
kconfig: Update ncurses package names for menuconfig
kbuild/kallsyms: trivial typo fix
kbuild: test --build-id linker flag by ld-option instead of cc-ldoption
kbuild: drop superfluous GCC_PLUGINS_CFLAGS assignment
kconfig: Don't leak choice names during parsing
sh: fix build error for empty CONFIG_BUILTIN_DTB_SOURCE
kconfig: set SYMBOL_AUTO to the symbol marked with defconfig_list
...
ivtv-alsa-mixer functions was introduced in commit 269c11fbac
("[media] ivtv, ivtv-alsa: Add initial ivtv-alsa interface driver for ivtv")
But according to commit message, ivtv-alsa-mixer.c was already dead code.
5 years after, we should remove it.
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
[hans.verkuil@cisco.com: removed forgotten ivtv-alsa-mixer.h include]
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
cx18-alsa-mixer functions are not used since commit 4cb565cc27
("V4L/DVB: cx18: make it so cx18-alsa-main.c compiles") 9 year later,
let's just remove them.
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add suffix LL to constant 1000000 in order to give the compiler
complete information about the proper arithmetic to use. Notice
that this constant is used in a context that expects an expression
of type ktime_t (64 bits, signed).
The expression ir->polling * 1000000 is currently being evaluated
using 32-bit arithmetic.
Addresses-Coverity-ID: 1392628 ("Unintentional integer overflow")
Addresses-Coverity-ID: 1392630 ("Unintentional integer overflow")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Currently an out of range dev->nr is detected by just reporting the
issue and later on an out-of-bounds read on array card occurs because
of this. Fix this by checking the upper range of dev->nr with the size
of array card (removes the hard coded size), move this check earlier
and also exit with the error -ENOSYS to avoid the later out-of-bounds
array read.
Detected by CoverityScan, CID#711191 ("Out-of-bounds-read")
Fixes: commit 02b20b0b4c ("V4L/DVB (12730): Add conexant cx25821 driver")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
[hans.verkuil@cisco.com: %ld -> %zd]
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Now that we have support for a buffer counter and for
error flags, update them at DMX_DQBUF.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This is to avoid pending interrupts to be handled during
stream off, in which case, the ready buffer will be removed
from buffer list, thus not all buffers can be returned to VB2
as expected. Disable CIO2 irq at cio2_hw_exit() so no new
interrupts are generated.
Signed-off-by: Yong Zhi <yong.zhi@intel.com>
Signed-off-by: Tianshu Qiu <tian.shu.qiu@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Replace the old license information with the corresponding SPDX
license.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This is the mindless scripted replacement of kernel use of POLL*
variables as described by Al, done by this script:
for V in IN OUT PRI ERR RDNORM RDBAND WRNORM WRBAND HUP RDHUP NVAL MSG; do
L=`git grep -l -w POLL$V | grep -v '^t' | grep -v /um/ | grep -v '^sa' | grep -v '/poll.h$'|grep -v '^D'`
for f in $L; do sed -i "-es/^\([^\"]*\)\(\<POLL$V\>\)/\\1E\\2/" $f; done
done
with de-mangling cleanups yet to come.
NOTE! On almost all architectures, the EPOLL* constants have the same
values as the POLL* constants do. But they keyword here is "almost".
For various bad reasons they aren't the same, and epoll() doesn't
actually work quite correctly in some cases due to this on Sparc et al.
The next patch from Al will sort out the final differences, and we
should be all done.
Scripted-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-----BEGIN PGP SIGNATURE-----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=H9AS
-----END PGP SIGNATURE-----
Merge tag 'media/v4.16-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- videobuf2 was moved to a media/common dir, as it is now used by the
DVB subsystem too
- Digital TV core memory mapped support interface
- new sensor driver: ov7740
- several improvements at ddbridge driver
- new V4L2 driver: IPU3 CIO2 CSI-2 receiver unit, found on some Intel
SoCs
- new tuner driver: tda18250
- finally got rid of all LIRC staging drivers
- as we don't have old lirc drivers anymore, restruct the lirc device
code
- add support for UVC metadata
- add a new staging driver for NVIDIA Tegra Video Decoder Engine
- DVB kAPI headers moved to include/media
- synchronize the kAPI and uAPI for the DVB subsystem, removing the gap
for non-legacy APIs
- reduce the kAPI gap for V4L2
- lots of other driver enhancements, cleanups, etc.
* tag 'media/v4.16-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (407 commits)
media: v4l2-compat-ioctl32.c: make ctrl_is_pointer work for subdevs
media: v4l2-compat-ioctl32.c: refactor compat ioctl32 logic
media: v4l2-compat-ioctl32.c: don't copy back the result for certain errors
media: v4l2-compat-ioctl32.c: drop pr_info for unknown buffer type
media: v4l2-compat-ioctl32.c: copy clip list in put_v4l2_window32
media: v4l2-compat-ioctl32.c: fix ctrl_is_pointer
media: v4l2-compat-ioctl32.c: copy m.userptr in put_v4l2_plane32
media: v4l2-compat-ioctl32.c: avoid sizeof(type)
media: v4l2-compat-ioctl32.c: move 'helper' functions to __get/put_v4l2_format32
media: v4l2-compat-ioctl32.c: fix the indentation
media: v4l2-compat-ioctl32.c: add missing VIDIOC_PREPARE_BUF
media: v4l2-ioctl.c: don't copy back the result for -ENOTTY
media: v4l2-ioctl.c: use check_fmt for enum/g/s/try_fmt
media: vivid: fix module load error when enabling fb and no_error_inj=1
media: dvb_demux: improve debug messages
media: dvb_demux: Better handle discontinuity errors
media: cxusb, dib0700: ignore XC2028_I2C_FLUSH
media: ts2020: avoid integer overflows on 32 bit machines
media: i2c: ov7740: use gpio/consumer.h instead of gpio.h
media: entity: Add a nop variant of media_entity_cleanup
...
Pull poll annotations from Al Viro:
"This introduces a __bitwise type for POLL### bitmap, and propagates
the annotations through the tree. Most of that stuff is as simple as
'make ->poll() instances return __poll_t and do the same to local
variables used to hold the future return value'.
Some of the obvious brainos found in process are fixed (e.g. POLLIN
misspelled as POLL_IN). At that point the amount of sparse warnings is
low and most of them are for genuine bugs - e.g. ->poll() instance
deciding to return -EINVAL instead of a bitmap. I hadn't touched those
in this series - it's large enough as it is.
Another problem it has caught was eventpoll() ABI mess; select.c and
eventpoll.c assumed that corresponding POLL### and EPOLL### were
equal. That's true for some, but not all of them - EPOLL### are
arch-independent, but POLL### are not.
The last commit in this series separates userland POLL### values from
the (now arch-independent) kernel-side ones, converting between them
in the few places where they are copied to/from userland. AFAICS, this
is the least disruptive fix preserving poll(2) ABI and making epoll()
work on all architectures.
As it is, it's simply broken on sparc - try to give it EPOLLWRNORM and
it will trigger only on what would've triggered EPOLLWRBAND on other
architectures. EPOLLWRBAND and EPOLLRDHUP, OTOH, are never triggered
at all on sparc. With this patch they should work consistently on all
architectures"
* 'misc.poll' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (37 commits)
make kernel-side POLL... arch-independent
eventpoll: no need to mask the result of epi_item_poll() again
eventpoll: constify struct epoll_event pointers
debugging printk in sg_poll() uses %x to print POLL... bitmap
annotate poll(2) guts
9p: untangle ->poll() mess
->si_band gets POLL... bitmap stored into a user-visible long field
ring_buffer_poll_wait() return value used as return value of ->poll()
the rest of drivers/*: annotate ->poll() instances
media: annotate ->poll() instances
fs: annotate ->poll() instances
ipc, kernel, mm: annotate ->poll() instances
net: annotate ->poll() instances
apparmor: annotate ->poll() instances
tomoyo: annotate ->poll() instances
sound: annotate ->poll() instances
acpi: annotate ->poll() instances
crypto: annotate ->poll() instances
block: annotate ->poll() instances
x86: annotate ->poll() instances
...
With "pages" initialized to vb length + 1 pages, the condition
check if(!pages--) will break at one more page than intended,
this can result in out-of-bound access to b->lop[i][j] when setting
the last dummy page.
Fixes: c7cbef1fdb ("media: intel-ipu3: cio2: fix a crash with out-of-bounds access")
Signed-off-by: Yong Zhi <yong.zhi@intel.com>
Signed-off-by: Cao Bing Bu <bingbu.cao@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
My earlier patch missed two functions, these must be __maybe_unused
as well:
drivers/media/pci/intel/ipu3/ipu3-cio2.c:1867:12: error: 'cio2_runtime_resume' defined but not used [-Werror=unused-function]
drivers/media/pci/intel/ipu3/ipu3-cio2.c:1849:12: error: 'cio2_runtime_suspend' defined but not used [-Werror=unused-function]
Fixes: 2086dd3570 ("media: intel-ipu3: cio2: mark PM functions as __maybe_unused")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The cobalt sound driver has a dependency on ALSA, but not
on the PCM helper code, so this can lead to an extremely
rare link error in randconfig builds:
ERROR: "snd_pcm_period_elapsed" [drivers/media/pci/cobalt/cobalt.ko] undefined!
ERROR: "_snd_pcm_stream_lock_irqsave" [drivers/media/pci/cobalt/cobalt.ko] undefined!
ERROR: "snd_pcm_hw_constraint_integer" [drivers/media/pci/cobalt/cobalt.ko] undefined!
ERROR: "snd_pcm_set_ops" [drivers/media/pci/cobalt/cobalt.ko] undefined!
ERROR: "snd_pcm_stream_unlock_irqrestore" [drivers/media/pci/cobalt/cobalt.ko] undefined!
ERROR: "snd_pcm_lib_ioctl" [drivers/media/pci/cobalt/cobalt.ko] undefined!
ERROR: "snd_pcm_new" [drivers/media/pci/cobalt/cobalt.ko] undefined!
The other audio drivers select 'SND_PCM' for this, so let's
do the same.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
cio2 driver should release buffer with QUEUED state
when start_stream op failed, wrong buffer state will
cause vb2 core throw a warning.
Signed-off-by: Yong Zhi <yong.zhi@intel.com>
Signed-off-by: Cao Bing Bu <bingbu.cao@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When dmabuf is used for BLOB type frame, the frame
buffers allocated by gralloc will hold more pages
than the valid frame data due to height alignment.
In this case, the page numbers in sg list could exceed the
FBPT upper limit value - max_lops(8)*1024 to cause crash.
Limit the LOP access to the valid data length
to avoid FBPT sub-entries overflow.
Signed-off-by: Yong Zhi <yong.zhi@intel.com>
Signed-off-by: Cao Bing Bu <bingbu.cao@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The driver apparently assumes that the device uses the same page size
as the CPU, but also assumes that this is 4096 bytes. On architectures
with a larger page size like 65536 bytes, we get a warning about an
integer overflow:
drivers/media/pci/intel/ipu3/ipu3-cio2.c: In function 'cio2_fbpt_entry_init_dummy':
arch/arm64/include/asm/page-def.h:28:20: error: large integer implicitly truncated to unsigned type [-Werror=overflow]
#define PAGE_SIZE (_AC(1, UL) << PAGE_SHIFT)
^
drivers/media/pci/intel/ipu3/ipu3-cio2.h:404:26: note: in expansion of macro 'PAGE_SIZE'
#define CIO2_PAGE_SIZE PAGE_SIZE
^~~~~~~~~
drivers/media/pci/intel/ipu3/ipu3-cio2.c:172:3: note: in expansion of macro 'CIO2_PAGE_SIZE'
CIO2_PAGE_SIZE / sizeof(u32) * CIO2_MAX_LOPS;
Obviously this won't work, but the driver is also unlikely to ever be
used on such an architecture, so the easiest workaround is to define
the CIO2_PAGE_SIZE macro to the size that the hardware actually uses.
Fixes: c2a6a07afe ("media: intel-ipu3: cio2: add new MIPI-CSI2 driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When CONFIG_PM is disabled, we get harmless warnings about the
suspend/resume callbacks being unused:
drivers/media/pci/intel/ipu3/ipu3-cio2.c:1993:12: error: 'cio2_resume' defined but not used [-Werror=unused-function]
drivers/media/pci/intel/ipu3/ipu3-cio2.c:1967:12: error: 'cio2_suspend' defined but not used [-Werror=unused-function]
This marks them as __maybe_unused to shut up the warnings.
Fixes: c2a6a07afe ("media: intel-ipu3: cio2: add new MIPI-CSI2 driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The arr_size() macro which is used to calculate the size of the chunk in the
array to be arranged resembles ARRAY_SIZE naming-wise. Avoid confusion by
renaming it to CHUNK_SIZE instead.
Also use min() macro to calculate the minimum of two numbers.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There are a lot of places where sequences of space/tabs are
found. Get rid of all spaces before tabs.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
On several places, whitespaces are being used for indentation,
or even at the end of the line.
Fix them.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Most of the I2C headers got moved a long time ago to
include/media/i2c. Stop including them at the patch.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Move the CI teardown code to ddbridge-ci.c where everything else related
to CI hardware lives.
Cc: Ralph Metzler <rjkm@metzlerbros.de>
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
As all error handling improved quite a bit, don't stop attaching frontends
if one of them failed, since - if other tuner modules are connected to
the PCIe bridge - other hardware may just work, so don't break on a single
port failure, but rather initialise as much as possible. Ie. if there are
issues with a C2T2-equipped PCIe bridge card which has additional DuoFlex
modules connected and the bridge generally works, the DuoFlex tuners can
still work fine.
If all ports failed to initialise where connected hardware was detected on
at first, return -ENODEV though to cause this PCI device to fail and free
all allocated resources. In any case, leave a kernel log warning (or
error, even) if things went wrong.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
In ddb_ports_attach(), if the second input of a dual tuner failed to
initialise, the first one can be detached (and resources be freed) as
this will be counted as the whole port having failed to initialise,
thus the first one won't be used anyway.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
In ddb_init(), the deinitialization sequence isn't correct when handling
errors, and could even lead to a memleak depending on where things failed.
Fix the deinit order.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
All CI types do dvb_ca_en50221_init() with the same arguments. Move this
call after the switch-case to remove the repetition in every case block.
Cc: Ralph Metzler <rjkm@metzlerbros.de>
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
In dvb_input_attach(), whenever a demod driver fails to initialise, or if
frontend registration fails, perform a full input/frontend teardown using
dvb_input_detach() (which can safely be done since the current init state
is tracked in the 'attached' struct member). Claimed resources thus are
freed which aren't needed when an input or a port is not functional.
While at it, in ddb_ports_detach(), detach the secondary input first. Also
increase the kernlog severity of TDA18212 errors and tuner failures in
general.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Do kfree() on port->en->data instead of port->en. port->en only holds a
ptr to a struct dvb_ca_en50221, which is a member either of a memalloc'ed
struct ddb_ci (DuoFlex CI, Octopus CI Duo) or a struct cxd (CXD2099AR
based Single Flex, allocated by the cxd2099 driver). port->en.data
though holds the ptr to the allocated memory, which must rather be
kfree()'d. Change this accordingly.
Cc: Ralph Metzler <rjkm@metzlerbros.de>
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use the existing PCI_EXP_DEVCTL2_COMP_TIMEOUT macro instead of hard-coding
the PCIe Completion Timeout Value mask. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
In the past, the same I2C address were used on multiple places.
After I2C rebinding changes, this is no longer needed. So, we
can just get rid of this header, placing the I2C address where
they belong, e. g. either at bttv driver or at tvtuner.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Using enums makes easier to document, as it can use kernel-doc
markups. It also allows cross-referencing, with increases the
kAPI readability.
Please notice that now cx88_querycap() has to have a default for
the VFL type, as there are more types than supported by the driver.
Acked-By: Mike Isely <isely@pobox.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
While the failure handling in dvb_input_attach() has been improved lately
so any tuner failure won't result in demod driver modules with a
usecount > 0 anymore (thus requiring rmmod -f), there's still an issue
with stv090x and stv0910 based tuner modules, in that LNB driver attach
failures leave an attached demod frontend driver behind which have a
usecount of > 0 in this failure case, due to them not being detached/
released. Fix this by detaching the demod frontends if the LNB driver
fails.
Richard tested and verified the changes with STV0910 hardware, thus adding
his Tested-by.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Tested-by: Richard Scobie <rascobie@slingshot.co.nz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
These two devices ids are really just one device with multiple
addresses. Probing becomes much simpler if we simply fold this into
one i2c device with two address.
Note that this breaks the lirc_zilog driver, however we will teach
ir-kbd-i2c to do what lirc_zilog does in a later commit.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
With the parent set for the rc device, the messages clearly state
that it is attached via i2c. The additional printk is unnecessary.
These are the old messages:
rc rc1: i2c IR (Hauppauge WinTV PVR-150 as /devices/virtual/rc/rc1
ir-kbd-i2c: i2c IR (Hauppauge WinTV PVR-150 detected at i2c-10/10-0071/ir0 [ivtv i2c driver #0]
Now we simply get:
rc rc1: Hauppauge WinTV PVR-150 as /devices/pci0000:00/0000:00:1e.0/0000:02:00.0/i2c-10/10-0071/rc/rc1
Note that we no longer copy the name. I've checked all call sites
to verfiy this is not a problem.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This is odd to call 'pci_disable_device()' in an error path before a
coresponding successful 'pci_enable_device()'.
Return directly instead.
Fixes: 77e0be1210 ("V4L/DVB (4176): Bug-fix: Fix memory overflow")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This change makes sure that demod frontends are always detached whenever
a tuner frontend attach failed. Achieve this by moving the detach-on-
failure logic at the end of dvb_input_attach(), and adding a goto to this
block on every tuner attach failure case, so if an error occurs, there are
no stray attached frontends left. As a side effect, this removes some
duplicated code.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fix almost all of checkpatch --strict warnings.
The remaining warnings are about:
* macro REG16 (should be enclosed in parentheses)
* macro REG16 (Macro argument reuse)
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
As warned by smatch:
drivers/media/pci/cx25821/cx25821-alsa.c:155 cx25821_alsa_dma_init() warn: argument 3 to %08lx specifier is cast from pointer
Use the standard %p to print a pointer.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
pt1_nr_tables is a modprobe parameter. The way the logic
handles it, it can't be negative. However, user can
set it to zero.
If set to zero, however, it will cause troubles at
pt1_init_tables(), as reported by smatch:
drivers/media/pci/pt1/pt1.c:468 pt1_init_tables() error: uninitialized symbol 'first_pfn'.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Update the driver version number/string to 0.9.32-integrated.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add a ddb_ prefix to the two functions to better avoid conflicts in the
global namespace, ie. when building everything into the kernel image.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Rename the MaxS4/8 support files following upstream. References to these
files and descriptions have been updated aswell.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
slot_ts_enable_xo2() logged debug output to info instead of debug, so
fix this up.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Move all CI device support related code from ddbridge-core to ddbridge-ci,
following the previously split off MaxS4/8 support.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fixes several alignment, braces, space-before-cast, camelcase et al issues
reported by checkpatch --strict, plus a few more checkpatch didn't report.
Three checks are left after this though:
- one CamelCase in ddbridge-core, related to defines/vars/enums referenced
from the stv090x demod driver
- one macro argument reuse in ddbridge-core aswell
- one unbalanced braces around else in ddbridge-main, which is due to
#ifdefs related to CONFIG_PCI_MSI, which preferrably should be kept
as-is for readability.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
These are only used in C/T demod attach functions, don't add any real
benefit (ie. line length savings) and in case of cxd28xx_attach aren't
even used consequently. Remove them.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
solo6x10 correctly deals with time stamps and will never
suffer from overflows, but it uses the deprecated 'struct timespec'
type and 'ktime_get_ts()' interface to read the monotonic clock.
This changes it to use ktime_get_ts64() instead, so we can
eventually remove ktime_get_ts().
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ismael Luceno <ismael@iodev.co.uk>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
kasprintf() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The pointer h is already initialized to codeclist_top so the second
identical assignment is redundant and can be removed. Cleans up clang
warning:
drivers/media/pci/zoran/videocodec.c:322:21: warning: Value stored to 'h'
during its initialization is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Variable mask is being set to 0x80 and then set to this value again
in the following for-loop. Remove the extraneous first setting of mask.
Cleans up clang warning:
drivers/media/pci/pt3/pt3_i2c.c:88:2: warning: Value stored to 'mask'
is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Using the ARRAY_SIZE macro improves the readability of the code. Also,
it is not always useful to use a variable to store this constant
calculated at compile time.
Found with Coccinelle with the following semantic patch:
@r depends on (org || report)@
type T;
T[] E;
position p;
@@
(
(sizeof(E)@p /sizeof(*E))
|
(sizeof(E)@p /sizeof(E[...]))
|
(sizeof(E)@p /sizeof(T))
)
Signed-off-by: Jérémy Lefaure <jeremy.lefaure@lse.epita.fr>
Reviewed-by: Michael Ira Krufky <mkrufky@linuxtv.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When building without CONFIG_GPIOLIB, we get a harmless
warning about an unused variable:
drivers/media/pci/solo6x10/solo6x10-gpio.c: In function 'solo_gpio_init':
drivers/media/pci/solo6x10/solo6x10-gpio.c:165:6: error: unused variable 'ret' [-Werror=unused-variable]
This adds another #ifdef around the declaration.
Fixes: d3202d1981 ("media: solo6x10: export hardware GPIO pins 8:31 to gpiolib interface")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ismael Luceno <ismael@iodev.co.uk>
Acked-by: Anton Sviridenko <anton@corp.bluecherry.net>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Several comments are wrongly tagged as kernel-doc, causing
those warnings:
drivers/media/rc/st_rc.c:98: warning: No description found for parameter 'irq'
drivers/media/rc/st_rc.c:98: warning: No description found for parameter 'data'
drivers/media/pci/solo6x10/solo6x10-enc.c:183: warning: No description found for parameter 'solo_dev'
drivers/media/pci/solo6x10/solo6x10-enc.c:183: warning: No description found for parameter 'ch'
drivers/media/pci/solo6x10/solo6x10-enc.c:183: warning: No description found for parameter 'qp'
drivers/media/usb/pwc/pwc-dec23.c:652: warning: Cannot understand *
on line 652 - I thought it was a doc line
drivers/media/usb/dvb-usb/cinergyT2-fe.c:40: warning: No description found for parameter 'op'
drivers/media/usb/dvb-usb/friio-fe.c:301: warning: Cannot understand * (reg, val) commad list to initialize this module.
on line 301 - I thought it was a doc line
drivers/media/rc/streamzap.c:201: warning: No description found for parameter 'urb'
drivers/media/rc/streamzap.c:333: warning: No description found for parameter 'intf'
drivers/media/rc/streamzap.c:333: warning: No description found for parameter 'id'
drivers/media/rc/streamzap.c:464: warning: No description found for parameter 'interface'
drivers/media/i2c/ov5647.c:432: warning: Cannot understand * @short Subdev core operations registration
on line 432 - I thought it was a doc line
drivers/media/usb/dvb-usb/friio.c:35: warning: No description found for parameter 'd'
drivers/media/usb/dvb-usb/friio.c:35: warning: No description found for parameter 'addr'
drivers/media/usb/dvb-usb/friio.c:35: warning: No description found for parameter 'wbuf'
drivers/media/usb/dvb-usb/friio.c:35: warning: No description found for parameter 'wlen'
drivers/media/usb/dvb-usb/friio.c:35: warning: No description found for parameter 'rbuf'
drivers/media/usb/dvb-usb/friio.c:35: warning: No description found for parameter 'rlen'
drivers/media/platform/vim2m.c:350: warning: No description found for parameter 'priv'
drivers/media/dvb-frontends/tua6100.c:34: warning: cannot understand function prototype: 'struct tua6100_priv '
drivers/media/platform/sti/hva/hva-h264.c:140: warning: cannot understand function prototype: 'struct hva_h264_stereo_video_sei '
drivers/media/platform/sti/hva/hva-h264.c:150: warning: Cannot understand * @frame_width: width in pixels of the buffer containing the input frame
on line 150 - I thought it was a doc line
drivers/media/platform/sti/hva/hva-h264.c:356: warning: Cannot understand * @ slice_size: slice size
on line 356 - I thought it was a doc line
drivers/media/platform/sti/hva/hva-h264.c:369: warning: Cannot understand * @ bitstream_size: bitstream size
on line 369 - I thought it was a doc line
drivers/media/platform/sti/hva/hva-h264.c:395: warning: Cannot understand * @seq_info: sequence information buffer
on line 395 - I thought it was a doc line
drivers/media/dvb-frontends/sp887x.c:137: warning: No description found for parameter 'fe'
drivers/media/dvb-frontends/sp887x.c:137: warning: No description found for parameter 'fw'
drivers/media/dvb-frontends/sp887x.c:287: warning: No description found for parameter 'n'
drivers/media/dvb-frontends/sp887x.c:287: warning: No description found for parameter 'd'
drivers/media/dvb-frontends/sp887x.c:287: warning: No description found for parameter 'quotient_i'
drivers/media/dvb-frontends/sp887x.c:287: warning: No description found for parameter 'quotient_f'
drivers/media/usb/ttusb-budget/dvb-ttusb-budget.c:83: warning: cannot understand function prototype: 'struct ttusb '
drivers/media/platform/sh_veu.c:277: warning: No description found for parameter 'priv'
drivers/media/dvb-frontends/zl10036.c:33: warning: cannot understand function prototype: 'int zl10036_debug; '
drivers/media/dvb-frontends/zl10036.c:179: warning: No description found for parameter 'state'
drivers/media/dvb-frontends/zl10036.c:179: warning: No description found for parameter 'frequency'
drivers/media/platform/rcar_fdp1.c:1139: warning: No description found for parameter 'priv'
drivers/media/platform/ti-vpe/vpe.c:933: warning: No description found for parameter 'priv'
drivers/media/usb/gspca/ov519.c:36: warning: No description found for parameter 'fmt'
drivers/media/usb/dvb-usb/dib0700_devices.c:3367: warning: No description found for parameter 'adap'
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There is a bad kernel-doc markup, producing the following warnings:
drivers/media/pci/netup_unidvb/netup_unidvb_core.c:85: warning: bad line: Bits [0-7]: DMA packet size, 188 bytes
drivers/media/pci/netup_unidvb/netup_unidvb_core.c:86: warning: bad line: Bits [16-23]: packets count in block, 128 packets
drivers/media/pci/netup_unidvb/netup_unidvb_core.c:87: warning: bad line: Bits [24-31]: blocks count, 8 blocks
drivers/media/pci/netup_unidvb/netup_unidvb_core.c:89: warning: bad line: For example, value of 375000000 equals to 3 sec
Fix that, and use a list for the bits option, in order for it
to be better format, if we add it to a driver's documentation
file.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There are a few mistakes on the existing markups:
drivers/media/pci/tw68/tw68-risc.c:32: warning: Cannot understand * @rp pointer to current risc program position
on line 32 - I thought it was a doc line
drivers/media/pci/tw68/tw68-risc.c:144: warning: No description found for parameter 'pci'
drivers/media/pci/tw68/tw68-risc.c:144: warning: No description found for parameter 'buf'
drivers/media/pci/tw68/tw68-risc.c:144: warning: No description found for parameter 'sglist'
drivers/media/pci/tw68/tw68-risc.c:144: warning: No description found for parameter 'top_offset'
drivers/media/pci/tw68/tw68-risc.c:144: warning: No description found for parameter 'bottom_offset'
drivers/media/pci/tw68/tw68-risc.c:144: warning: No description found for parameter 'bpl'
drivers/media/pci/tw68/tw68-risc.c:144: warning: No description found for parameter 'padding'
drivers/media/pci/tw68/tw68-risc.c:144: warning: No description found for parameter 'lines'
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
As warned:
drivers/media/pci/sta2x11/sta2x11_vip.c:414: warning: No description found for parameter 'priv'
drivers/media/pci/sta2x11/sta2x11_vip.c:442: warning: No description found for parameter 'priv'
drivers/media/pci/sta2x11/sta2x11_vip.c:476: warning: No description found for parameter 'priv'
drivers/media/pci/sta2x11/sta2x11_vip.c:493: warning: No description found for parameter 'priv'
drivers/media/pci/sta2x11/sta2x11_vip.c:524: warning: No description found for parameter 'priv'
drivers/media/pci/sta2x11/sta2x11_vip.c:548: warning: No description found for parameter 'priv'
drivers/media/pci/sta2x11/sta2x11_vip.c:566: warning: No description found for parameter 'file'
drivers/media/pci/sta2x11/sta2x11_vip.c:566: warning: No description found for parameter 'priv'
drivers/media/pci/sta2x11/sta2x11_vip.c:594: warning: No description found for parameter 'priv'
drivers/media/pci/sta2x11/sta2x11_vip.c:651: warning: No description found for parameter 'priv'
drivers/media/pci/sta2x11/sta2x11_vip.c:717: warning: No description found for parameter 'priv'
Most of the above are for the unused priv argument.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
-----BEGIN PGP SIGNATURE-----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=d9nT
-----END PGP SIGNATURE-----
Merge tag 'media/v4.15-1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- Documentation for digital TV (both kAPI and uAPI) are now in sync
with the implementation (except for legacy/deprecated ioctls). This
is a major step, as there were always a gap there
- New sensor driver: imx274
- New cec driver: cec-gpio
- New platform driver for rockship rga and tegra CEC
- New RC driver: tango-ir
- Several cleanups at atomisp driver
- Core improvements for RC, CEC, V4L2 async probing support and DVB
- Lots of drivers cleanup, fixes and improvements.
* tag 'media/v4.15-1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (332 commits)
dvb_frontend: don't use-after-free the frontend struct
media: dib0700: fix invalid dvb_detach argument
media: v4l2-ctrls: Don't validate BITMASK twice
media: s5p-mfc: fix lockdep warning
media: dvb-core: always call invoke_release() in fe_free()
media: usb: dvb-usb-v2: dvb_usb_core: remove redundant code in dvb_usb_fe_sleep
media: au0828: make const array addr_list static
media: cx88: make const arrays default_addr_list and pvr2000_addr_list static
media: drxd: make const array fastIncrDecLUT static
media: usb: fix spelling mistake: "synchronuously" -> "synchronously"
media: ddbridge: fix build warnings
media: av7110: avoid 2038 overflow in debug print
media: Don't do DMA on stack for firmware upload in the AS102 driver
media: v4l: async: fix unregister for implicitly registered sub-device notifiers
media: v4l: async: fix return of unitialized variable ret
media: imx274: fix missing return assignment from call to imx274_mode_regs
media: camss-vfe: always initialize reg at vfe_set_xbar_cfg()
media: atomisp: make function calls cleaner
media: atomisp: get rid of storage_class.h
media: atomisp: get rid of wrong stddef.h include
...
Summary of modules changes for the 4.15 merge window:
- Treewide module_param_call() cleanup, fix up set/get function
prototype mismatches, from Kees Cook
- Minor code cleanups
Signed-off-by: Jessica Yu <jeyu@kernel.org>
-----BEGIN PGP SIGNATURE-----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=c8vb
-----END PGP SIGNATURE-----
Merge tag 'modules-for-v4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/jeyu/linux
Pull module updates from Jessica Yu:
"Summary of modules changes for the 4.15 merge window:
- treewide module_param_call() cleanup, fix up set/get function
prototype mismatches, from Kees Cook
- minor code cleanups"
* tag 'modules-for-v4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/jeyu/linux:
module: Do not paper over type mismatches in module_param_call()
treewide: Fix function prototypes for module_param_call()
module: Prepare to convert all module_param_call() prototypes
kernel/module: Delete an error message for a failed memory allocation in add_module_usage()
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJZ/30WAAoJEHm+PkMAQRiG1YkIAIVgcZS9SPzjcH+/NpcNJ4wv
Bp8xyfj/X6Eswn63ebrV/qij65Esmha7wnSREcFqrfNecRwOAdvYCjj20jqKGws2
p03sOS4aVSpJSQcqJ9sdF3Xx/P7CcK4IAjr0ihQbqozXiZAgVzTlYJwB+ErBMWFU
6NFYXg/Xp7FJXJ0o14yHpZ4RqgbLV95CgFIG9hzwvCibsW6ZBvGtYBD99IjeojPg
rw+B+Osck7XjC6IHqF/u760nTOaP8vVlTrCRqvFityGS9ZFQZDzEKYqxYgk8cVFC
jzR3fuHiWiomhyP9dLUZn6UuYQTaThhY58LvsEwV0JVJH9mUwcA4u5nO0wDUCO4=
=hhQa
-----END PGP SIGNATURE-----
Merge tag 'v4.14-rc8' into next
Merge with mainline to bring in SPDX markings to avoid annoying merge
problems when some header files get deleted.
Don't populate arrays default_addr_list and pvr2000_addr_list on the
stack but instead make them static. Makes the object code smaller by
over 340 bytes:
Before:
text data bss dec hex filename
12520 2800 64 15384 3c18 drivers/media/pci/cx88/cx88-input.o
After:
text data bss dec hex filename
12142 2832 64 15038 3abe drivers/media/pci/cx88/cx88-input.o
(gcc version 7.2.0 x86_64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fix 2 build warnings.
These functions are void, so drop the "return"s.
./drivers/media/pci/ddbridge/ddbridge-io.h: warning: 'return' with a value, in function returning void [enabled by default]: => 50:2, 55:2
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Daniel Scheller <d.scheller.oss@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Using the deprecated do_gettimeofday() in print_time() will overflow
in 2038 on 32-bit architectures. It'sbetter to use a structure that
is safe everywhere. While we're at it, fix the missing leading zeroes
on the sub-second portion.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Leave the autorepeat handling up to the input layer, and move
to the new timer API.
Compile tested only.
Signed-off-by: Sean Young <sean@mess.org>
Acked-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Several function prototypes for the set/get functions defined by
module_param_call() have a slightly wrong argument types. This fixes
those in an effort to clean up the calls when running under type-enforced
compiler instrumentation for CFI. This is the result of running the
following semantic patch:
@match_module_param_call_function@
declarer name module_param_call;
identifier _name, _set_func, _get_func;
expression _arg, _mode;
@@
module_param_call(_name, _set_func, _get_func, _arg, _mode);
@fix_set_prototype
depends on match_module_param_call_function@
identifier match_module_param_call_function._set_func;
identifier _val, _param;
type _val_type, _param_type;
@@
int _set_func(
-_val_type _val
+const char * _val
,
-_param_type _param
+const struct kernel_param * _param
) { ... }
@fix_get_prototype
depends on match_module_param_call_function@
identifier match_module_param_call_function._get_func;
identifier _val, _param;
type _val_type, _param_type;
@@
int _get_func(
-_val_type _val
+char * _val
,
-_param_type _param
+const struct kernel_param * _param
) { ... }
Two additional by-hand changes are included for places where the above
Coccinelle script didn't notice them:
drivers/platform/x86/thinkpad_acpi.c
fs/lockd/svc.c
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Jessica Yu <jeyu@kernel.org>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Andy Walls <awalls@md.metrocast.net>
Cc: Sergey Kozlov <serjk@netup.ru>
Cc: Abylay Ospan <aospan@netup.ru>
Cc: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Cc: Arvind Yadav <arvind.yadav.cs@gmail.com>
Cc: Geliang Tang <geliangtang@gmail.com>
Cc: Sean Young <sean@mess.org>
Cc: "Pali Rohár" <pali.rohar@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
[hans.verkuil@cisco.com: dropped pci/ttpci/av7110_ir.c patch chunk]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Make vb2_ops const as they are only stored in the const field of a
vb2_queue structure. Make the declarations const too.
Done using Coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Make this const as it is only used in a copy operation in the file
referencing it. Make the declaration const too.
Done using Coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Make this const as it is only passed to the const argument of the
function videobuf_queue_sg_init in the file referencing it.
Also, make the declaration in the header const.
Structure found using Coccinelle and changes done by hand.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Instead of using an integer to represent it, use boolean,
as this better describes what this field really means.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The help text should be indented by at least two spaces after the
'help' separator. This is both good practice and the media_build system
for building media drivers makes this assumption.
I went through all Kconfigs under drivers/media and fixed any bad help
sections. This makes it conform to the common practice and should fix
problems with 'make menuconfig' when using media_build. This is due to
a "WARNING" message that media_build can insert in the Kconfig and that
assumes the help text is indented by at least two spaces. If not, then the
Kconfig becomes invalid and 'make menuconfig' fails.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reported-by: Thomas Kaiser <linux-dvb@kaiser-linux.li>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
In the distant past the adv7604 driver used private controls. In order
to access them the v4l-subdevX nodes were needed. Later the is_private
tag was removed in the adv7604 driver and the need for v4l-subdevX
device nodes disappeared.
Remove the creation of those device nodes from this driver.
Note: the cobalt card is only used inside Cisco and we never actually
used the v4l-subdevX nodes for anything. So this API change can be done
safely without breaking anything.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The script "checkpatch.pl" pointed information out like the following.
ERROR: do not use assignment in if condition
Thus fix the affected source code place.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The script "checkpatch.pl" pointed information out like the following.
ERROR: do not use assignment in if condition
Thus fix the affected source code places.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Don't populate the array buf on the stack, instead make it static.
Makes the object code smaller by over 240 bytes:
Before:
text data bss dec hex filename
21689 22992 416 45097 b029 cx23885-cards.o
After:
text data bss dec hex filename
21348 23088 416 44852 af34 cx23885-cards.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The error handling paths all end up with retval being non-zero,
so the check for retval being zero is always false and hence
is redundant. Remove it.
Detected by CoverityScan CID#1309479 ("Logically dead code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Make these const as they are only used in a copy operation.
Done using Coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The script “checkpatch.pl” pointed information out like the following.
Comparison to NULL could be written !…
Thus fix the affected source code places.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Replace the specification of a data structure by a pointer dereference
as the parameter for the operator "sizeof" to make the corresponding size
determination a bit safer according to the Linux coding style convention.
This issue was detected by using the Coccinelle software.
[mchehab@s-opensoure.com: merge similar patches into one]
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
The variables will be set to an appropriate value before usage.
Thus omit the explicit initialisation at the beginning.
[mchehab@s-opensource.com: fold similar patches into one]
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Omit an extra message for a memory allocation failure in this function.
This issue was detected by using the Coccinelle software.
[mchehab@s-opensource.com: fold several similar patches into one]
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Pull more set_fs removal from Al Viro:
"Christoph's 'use kernel_read and friends rather than open-coding
set_fs()' series"
* 'work.set_fs' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
fs: unexport vfs_readv and vfs_writev
fs: unexport vfs_read and vfs_write
fs: unexport __vfs_read/__vfs_write
lustre: switch to kernel_write
gadget/f_mass_storage: stop messing with the address limit
mconsole: switch to kernel_read
btrfs: switch write_buf to kernel_write
net/9p: switch p9_fd_read to kernel_write
mm/nommu: switch do_mmap_private to kernel_read
serial2002: switch serial2002_tty_write to kernel_{read/write}
fs: make the buf argument to __kernel_write a void pointer
fs: fix kernel_write prototype
fs: fix kernel_read prototype
fs: move kernel_read to fs/read_write.c
fs: move kernel_write to fs/read_write.c
autofs4: switch autofs4_write to __kernel_write
ashmem: switch to ->read_iter
This ioctl is not implemented at dst_ca driver. There's just
a boilerplate code there. Remove it, as it is unlikely that
anyone would implement it those days.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Right now, on several places, the driver is returning a
"-1" error to userspace, instead of a proper error code.
Fix it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This ioctl seems to be some attempt to support a feature
at the bt8xx dst_ca driver. Yet, as said there, it
"needs more work". Right now, the code there is just
a boilerplate.
At the end of the day, no driver uses this ioctl, nor it is
documented anywhere (except for "needs more work").
So, get rid of it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Using typedefs inside the Kernel is against CodingStyle, and
there's no good usage here.
Just like we did at frontend.h, at commit 0df289a209 ("[media] dvb:
Get rid of typedev usage for enums"), let's keep those typedefs only
to provide userspace backward compatibility.
No functional changes.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use proper ssize_t and size_t types for the return value and count
argument, move the offset last and make it an in/out argument like
all other read/write helpers, and make the buf argument a void pointer
to get rid of lots of casts in the callers.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Add two new model numbers to suppress this message in kernel log:
cx23885: cx23885[0]: warning: unknown hauppauge model #121029
Add these model numbers:
* Model 121019 - WinTV-HVR4400
* Model 121029 - WinTV-HVR5500
For WinTV-HVR4400 the documentation and my hardware differ:
Documentation says it supports DVB-S/S2 and DVB-T,
but my hardware also supports DVB-C.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Make this const as it is only stored in a const field of a
video_device structure.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Make these const as they are either used during a copy operation or
passed to a const argument of the function cx88_vdev_init.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fix several
drivers/media/pci/ddbridge/ddbridge-core.c: warning: symbol ... was not declared. Should it be static?
drivers/media/pci/ddbridge/ddbridge-core.c: warning: Using plain integer as NULL pointer
drivers/media/pci/ddbridge/ddbridge-io.h: warning: cast removes address space of expression
drivers/media/pci/ddbridge/ddbridge-io.h: warning: incorrect type in argument 1 (different address spaces)
at multiple places.
Cc: Ralph Metzler <rjkm@metzlerbros.de>
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Brought to attention by Matthias Schwarzott <zzam@gentoo.org> by fixing
possible use-after-free faults in some demod drivers:
In ddb_input_detach(), the i2c_client is unregistered and removed before
dvb frontends are unregistered and detached. While no use-after-free issue
was observed so far, there is another issue with this:
dvb->attached keeps track of the state of the input/output registration,
and the i2c_client unregistration takes place only if everything was
successful (dvb->attached == 0x31). If for some reason an error occurred
during the frontend setup, that value stays at 0x20. In the following
error handling and cleanup, ddb_input_detach() will skip down to that
state, leaving the i2c_client registered, causing refcount issues.
Fix this by moving the i2c_client deregistration down to case 0x20.
Cc: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
videobuf_queue_ops are not supposed to change at runtime. All functions
working with videobuf_queue_ops provided by <media/videobuf-core.h> work
with const videobuf_queue_ops. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Make this const as it is only used in a copy operation.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Make this const as it is only used in a copy operation.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Make these const as they are only used in a copy operation.
Done using Coccinelle
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
RC_TYPE is confusing and it's just the protocol. So rename it.
Suggested-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Sean Young <sean@mess.org>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Any protocol for which we have a software decoder, can be enabled. Without
this only the loaded protocol decoders can be selected.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Since commit 12749b198fa4 ("[media] rc: saa7134: add trailing space for
timely decoding"), the workaround of inserting reset events is no
longer needed.
Note that the initial reset is not needed either; other rc-core drivers
that don't use ir_raw_event_store_edge() never call this at all.
Verified on a HVR-1150 and Raspberry Pi.
Fixes: 3f5c4c7332 ("[media] rc: fix ghost keypresses with certain hw")
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The gpio-ir-recv driver adds timeouts which the saa7134 lacks; this
causes keypress not to arrive, and to only arrive once more IR is
received. This is what the commit below calls "ghost keypresses",
and that commit does not solve the issue completely.
This makes the IR on the HVR-1150 much more reliable and responsive.
Fixes: 3f5c4c7332 ("[media] rc: fix ghost keypresses with certain hw")
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The gpio-ir-recv driver does many wakeups (once per edge); the saa7134
driver has special handling to only wakeup 15ms after the first edge.
Make this part of rc-core so gpio-ir-recv also benefits from
this (so a rc-5 keypress now causes 3 wakeups rather than 24).
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When an ir-spi is registered, you get this message.
rc rc0: Unspecified device as /devices/platform/soc/3f215080.spi/spi_master/spi32766/spi32766.128/rc/rc0
"Unspecified device" refers to input_name, which makes no sense for IR
TX only devices. So, rename to device_name.
Also make driver_name const char* so that no casts are needed anywhere.
Now ir-spi reports:
rc rc0: IR SPI as /devices/platform/soc/3f215080.spi/spi_master/spi32766/spi32766.128/rc/rc0
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The first argument of function snd_ctl_new1 is of type const struct
snd_kcontrol_new * but in this file the variable is passed by value
to this function. This generated ""incompatible type for argument"
error. So, pass the variable by reference.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The first argument of function snd_ctl_new1 is of type const struct
snd_kcontrol_new * but in this file the variable is passed by value to
this function.
This generated ""incompatible type for argument" error. So, pass the
variable by reference.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Make this const as it is only used during a copy operation.
Done using Coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Make this const as it only passed as the 1st argument to the function
snd_ctl_new1, which is of type const.
Done using Coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
These videobuf_queue_ops structures are only passed as the second
argument to videobuf_queue_vmalloc_init, which is declared as const.
Thus the videobuf_queue_ops structures themselves can be const.
Done with the help of Coccinelle.
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct videobuf_queue_ops i@p = { ... };
@ok1@
identifier r.i;
expression e1;
position p;
@@
videobuf_queue_vmalloc_init(e1,&i@p,...)
@bad@
position p != {r.p,ok1.p};
identifier r.i;
struct videobuf_queue_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct videobuf_queue_ops i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This v4l2_audio structure is only copied into other structures,
so it can be const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Make these const as they are only used during a copy operation.
Done using Coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
drivers/media/pci/ddbridge/ddbridge-core.c: In function 'ddb_port_attach':
drivers/media/pci/ddbridge/ddbridge-core.c:2261:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (ret < 0)
^
drivers/media/pci/ddbridge/ddbridge-core.c:2263:2: note: here
case DDB_PORT_LOOP:
^~~~
drivers/media/pci/ddbridge/ddbridge-core.c: In function 'dvb_input_attach':
drivers/media/pci/ddbridge/ddbridge-core.c:1492:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (input->port->dev->link[input->port->lnr].info->ts_quirks &
^
drivers/media/pci/ddbridge/ddbridge-core.c:1497:2: note: here
case DDB_TUNER_DVBCT2_SONY_P:
^~~~
drivers/media/pci/ddbridge/ddbridge-core.c:1516:9: warning: this statement may fall through [-Wimplicit-fallthrough=]
osc24 = 1;
~~~~~~^~~
drivers/media/pci/ddbridge/ddbridge-core.c:1517:2: note: here
case DDB_TUNER_DVBCT2_SONY:
^~~~
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
These structures are only copied into other structures, so
they can be const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
All data is accessed RO, so mark everything const. Some vars in several
functions aswell as function signatures also require the const keyword
now, they're also added by this commit.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Since the DD hardware info and maps aren't needed anymore outside of
ddbridge-hw.c (they're returned via get_ddb_info() now), mark them
static and remove all refs from ddbridge-hw.h.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
adapter_alloc is only used from within ddbridge-core, so move it there,
this removes the need for prototyping/referencing the variable. While at
it, msi isn't needed outside of ddbridge-main, so don't extref that one
aswell.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This further cleans up ddbridge-main from hardware-related data and moves
the exact card type determination into ddbridge-hw.c:get_ddb_info(), right
to the hardware maps/structs. Also, const'ify more structs and pointers.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Force gap setting if given by attribute and enable gap for older regmaps.
Also, setting a gap value of 128 via sysfs will now disable gap.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Picked up code parts introduced one smatch error:
drivers/media/pci/ddbridge/ddbridge-maxs8.c:163 max_set_input_unlocked() error: buffer overflow 'dev->link[port->lnr].lnb.voltage' 4 <= 255
Fix this by clamping the .lnb.voltage array access to 0-3 by "& 3"'ing
dvb->input.
Cc: Ralph Metzler <rjkm@metzlerbros.de>
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This enables MaxS4/S8 and Octopus Max card support in ddbridge by adding
glue code into ddbridge-core, having another PCI ID, and have the LNB IC
control code (and all other MaxS4/8 related code) in ddbridge-maxs8.c
(rather than another ~400 LoC in ddbridge-core.c like it's done in the
original vendor driver package).
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
It is known that MSI interrupts - while working quite well so far - can
still cause issues on some hardware platforms (causing I2C timeouts due
to unhandled interrupts). The msi variable/option is set to 1 by default.
So, add a Kconfig option prefixed with "EXPERIMENTAL" that will control
the default value of that modparam, defaulting to off for a better
user experience and (guaranteed) stable operation "per default".
Cc: Ralph Metzler <rjkm@metzlerbros.de>
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Tested-by: Richard Scobie <r.scobie@clear.net.nz>
Tested-by: Jasmin Jessich <jasmin@anw.at>
Tested-by: Dietmar Spingler <d_spingler@freenet.de>
Tested-by: Manfred Knick <Manfred.Knick@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Both ts_release() and ts_open() can use "output" before check (smatch):
drivers/media/pci/ddbridge/ddbridge-core.c:816 ts_release() warn: variable dereferenced before check 'output' (see line 809)
drivers/media/pci/ddbridge/ddbridge-core.c:836 ts_open() warn: variable dereferenced before check 'output' (see line 828)
Fix by performing checks on those pointers.
Cc: Ralph Metzler <rjkm@metzlerbros.de>
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Tested-by: Richard Scobie <r.scobie@clear.net.nz>
Tested-by: Jasmin Jessich <jasmin@anw.at>
Tested-by: Dietmar Spingler <d_spingler@freenet.de>
Tested-by: Manfred Knick <Manfred.Knick@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Smatch and gcc complained:
drivers/media/pci/ddbridge/ddbridge-core.c:3491 bpsnr_show() warn: impossible condition '(snr[0] == 255) => ((-128)-127 == 255)'
drivers/media/pci/ddbridge/ddbridge-core.c: In function ‘bpsnr_show’:
drivers/media/pci/ddbridge/ddbridge-core.c:3491:13: warning: comparison is always false due to limited range of data type [-Wtype-limits]
Fix this by changing the type of snr to unsigned char.
Cc: Ralph Metzler <rjkm@metzlerbros.de>
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Tested-by: Richard Scobie <r.scobie@clear.net.nz>
Tested-by: Jasmin Jessich <jasmin@anw.at>
Tested-by: Dietmar Spingler <d_spingler@freenet.de>
Tested-by: Manfred Knick <Manfred.Knick@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
>From smatch:
drivers/media/pci/ddbridge/ddbridge-core.c:3490 snr_store() info: ignoring unreachable code.
In fact, the function immediately returns zero, so remove it and update
ddb_attrs_snr[] to not reference it anymore.
Cc: Ralph Metzler <rjkm@metzlerbros.de>
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Tested-by: Richard Scobie <r.scobie@clear.net.nz>
Tested-by: Jasmin Jessich <jasmin@anw.at>
Tested-by: Dietmar Spingler <d_spingler@freenet.de>
Tested-by: Manfred Knick <Manfred.Knick@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Smatch reported:
drivers/media/pci/ddbridge/ddbridge-core.c:1602 dvb_input_attach() error: we previously assumed 'dvb->fe' could be null (see line 1595)
dvb->fe2 will ever only be populated when dvb->fe is set. So only handle
registration of dvb->fe2 when dvb->fe got set beforehand by moving the
registration into the "if (dvb->fe)" conditional.
Cc: Ralph Metzler <rjkm@metzlerbros.de>
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Tested-by: Richard Scobie <r.scobie@clear.net.nz>
Tested-by: Jasmin Jessich <jasmin@anw.at>
Tested-by: Dietmar Spingler <d_spingler@freenet.de>
Tested-by: Manfred Knick <Manfred.Knick@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fixes two warnings reported by smatch:
drivers/media/pci/ddbridge/ddbridge-core.c:240 ddb_redirect() warn: variable dereferenced before check 'idev' (see line 238)
drivers/media/pci/ddbridge/ddbridge-core.c:240 ddb_redirect() warn: variable dereferenced before check 'pdev' (see line 238)
Fixed by moving the existing checks up before accessing members.
Cc: Ralph Metzler <rjkm@metzlerbros.de>
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Tested-by: Richard Scobie <r.scobie@clear.net.nz>
Tested-by: Jasmin Jessich <jasmin@anw.at>
Tested-by: Dietmar Spingler <d_spingler@freenet.de>
Tested-by: Manfred Knick <Manfred.Knick@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Further cleanup of ddbridge-core and ddbridge-main, and moves all such
hw definitions into one single place, making things easier to maintain.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Tested-by: Richard Scobie <r.scobie@clear.net.nz>
Tested-by: Jasmin Jessich <jasmin@anw.at>
Tested-by: Dietmar Spingler <d_spingler@freenet.de>
Tested-by: Manfred Knick <Manfred.Knick@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
While it seems valid that headers can carry simple oneline static inline
annotated functions, move them into their own header file to have the
overall code more readable. Also, keep them as header (and don't put in
a separate object) and static inline to help the compiler avoid
generating function calls.
(Thanks to Jasmin J. <jasmin@anw.at> for valuable input on this!)
Cc: Jasmin J. <jasmin@anw.at>
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Tested-by: Richard Scobie <r.scobie@clear.net.nz>
Tested-by: Jasmin Jessich <jasmin@anw.at>
Tested-by: Dietmar Spingler <d_spingler@freenet.de>
Tested-by: Manfred Knick <Manfred.Knick@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This huge patch bumps the ddbridge driver to version 0.9.29. Compared to
the vendor driver package, DD OctoNET including GTL link support, and all
DVB-C Modulator card support has been removed since this requires large
changes to the underlying DVB core API, which should eventually be done
separately, and, after that, the functionality/device support can be added
back rather easy.
While the diff is rather large, the bump is mostly a big refactor of all
data structures. Yet, the MSI support (message signaled interrupts) is
greatly improved, also all currently available CI single/duo bridge cards
are fully supported.
More changes compared to the upstream driver:
- the DDB_USE_WORKER flag/define was removed, kernel worker functionality
will be used.
- coding style is properly fixed (zero complaints from checkpatch)
- all (not much though) CamelCase has been fixed to kernel_case
- (private) IOCTLs temporarily removed (which are mainly used to provide
rarely-used FPGA update functionality)
Great care has been taken to keep all previous changes and fixes (e.g.
kernel logging via dev_*(), pointer annotations and such) intact.
Permission to reuse and mainline the driver code was formally granted by
Ralph Metzler <rjkm@metzlerbros.de>.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Tested-by: Richard Scobie <r.scobie@clear.net.nz>
Tested-by: Jasmin Jessich <jasmin@anw.at>
Tested-by: Dietmar Spingler <d_spingler@freenet.de>
Tested-by: Manfred Knick <Manfred.Knick@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
As of 0.9.9b, the ddbridge code has been split from one single file
(ddbridge-core.c) into multiple files, with the purpose of taking care of
different topics, and to be able to reuse code in different kernel modules
(ddbridge.ko and octonet.ko). This applies the same code split, with a
notable difference:
In the vendor package, the split was done by moving all code parts into
separate files, and in the "main" code files (ddbridge.c and octonet.c),
a simple "#include ddbridge-core.c" was done.
In this patch, the same split (codewise) is done, but all resulting .c/.o
files will be handled by the makefile, with proper prototyping of all
shared functions done in ddbridge.h. To avoid conflicts wrt the global
space, the I2C functions and necessary prototypes for ddbridge-i2c.c are
moved into ddbridge-i2c.h, which is to be included wherever required.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Tested-by: Richard Scobie <r.scobie@clear.net.nz>
Tested-by: Jasmin Jessich <jasmin@anw.at>
Tested-by: Dietmar Spingler <d_spingler@freenet.de>
Tested-by: Manfred Knick <Manfred.Knick@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The functions in ddbridge-core.c have been moved to different positions in
newer versions of the dddvb vendor driver package (most notably in version
0.9.9b). Perform the same code move to keep the diff of the upcoming
code bump simpler.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Tested-by: Richard Scobie <r.scobie@clear.net.nz>
Tested-by: Jasmin Jessich <jasmin@anw.at>
Tested-by: Dietmar Spingler <d_spingler@freenet.de>
Tested-by: Manfred Knick <Manfred.Knick@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
24 GPIO pins from 32 available on solo6x10 chips are exported
to gpiolib. First 8 GPIOs are reserved for internal use on capture card
boards, GPIOs in range 8:15 are configured as outputs to control relays,
remaining 16:31 are configured as inputs to read sensor states.
Now with this patch userspace DVR software can switch relays and read
sensor states when GPIO extension cards are attached to Softlogic solo6x10
based video capture cards.
Signed-off-by: Anton Sviridenko <anton@corp.bluecherry.net>
Signed-off-by: Ismael Luceno <ismael@iodev.co.uk>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <media/drv-intf/saa7146.h>
and <linux/pci.h> work with const pci_device_id. So mark the non-const
structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <media/drv-intf/saa7146.h>
and <linux/pci.h> work with const pci_device_id. So mark the non-const
structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <media/drv-intf/saa7146.h>
and <linux/pci.h> work with const pci_device_id. So mark the non-const
structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <media/drv-intf/saa7146.h>
and <linux/pci.h> work with const pci_device_id. So mark the non-const
structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <media/drv-intf/saa7146.h>
and <linux/pci.h> work with const pci_device_id. So mark the non-const
structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <media/drv-intf/saa7146.h>
and <linux/pci.h> work with const pci_device_id. So mark the non-const
structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <media/drv-intf/saa7146.h>
and <linux/pci.h> work with const pci_device_id. So mark the non-const
structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <media/drv-intf/saa7146.h>
and <linux/pci.h> work with const pci_device_id. So mark the non-const
structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This is used just for printing a version number. As this is
never incremented, it makes no sense to keep it :-)
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When a user starts and stops filtering at a demux device too quickly
in a very short interval, the user process hangs in uninterruptible sleep,
due to an inconsistency of kthread status in the driver.
The kthread can be stopped before it starts running its thread function,
but the invocation status was partly managed in the kthread function,
which resulted in a double kthread_stop() of one kthread.
Signed-off-by: Akihiro Tsukada <tskd08@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Check for i2c_algorithm structures that are only stored in
the algo field of an i2c_adapter structure. This field is
declared const, so i2c_algorithm structures that have this
property can be declared as const also.
This issue was identified using Coccinelle and the following
semantic patch:
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct i2c_algorithm i@p = { ... };
@ok@
identifier r.i;
struct i2c_adapter e;
position p;
@@
e.algo = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct i2c_algorithm i = { ... };
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Check for i2c_algorithm structures that are only stored in
the algo field of an i2c_adapter structure. This field is
declared const, so i2c_algorithm structures that have this
property can be declared as const also.
This issue was identified using Coccinelle and the following
semantic patch:
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct i2c_algorithm i@p = { ... };
@ok@
identifier r.i;
struct i2c_adapter e;
position p;
@@
e.algo = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct i2c_algorithm i = { ... };
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Check for i2c_algorithm structures that are only stored in
the algo field of an i2c_adapter structure. This field is
declared const, so i2c_algorithm structures that have this
property can be declared as const also.
This issue was identified using Coccinelle and the following
semantic patch:
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct i2c_algorithm i@p = { ... };
@ok@
identifier r.i;
struct i2c_adapter e;
position p;
@@
e.algo = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct i2c_algorithm i = { ... };
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Check for i2c_algorithm structures that are only stored in
the algo field of an i2c_adapter structure. This field is
declared const, so i2c_algorithm structures that have this
property can be declared as const also.
This issue was identified using Coccinelle and the following
semantic patch:
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct i2c_algorithm i@p = { ... };
@ok@
identifier r.i;
struct i2c_adapter e;
position p;
@@
e.algo = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct i2c_algorithm i = { ... };
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Adds a stv0910_single modparm which, when set, configures the stv0910 to
run in single demodulator mode, currently intended for high bit rate
testing.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Tested-by: Richard Scobie <r.scobie@clear.net.nz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This adds all required glue code to support - in conjunction with the new
stv0910 and stv6111 demod/tuner drivers and additionally the lnbh25 LNB
controller driver - all current DVB-S/S2 hardware (bridges and flex
modules) from Digital Devices like the DD CineS2 V7 and V7A, current
S2 V4 DuoFlex modules, and probably all upcoming devices based on this
STV0910/STV6111/LNBH25 hardware stack.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Tested-by: Richard Scobie <r.scobie@clear.net.nz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The returned value is required for further evaluation of the exact
demodulator chip (stv090x or stv0910).
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Tested-by: Richard Scobie <r.scobie@clear.net.nz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This patch enables support for non-Bluecherry labeled solo6110
based PCI cards which have 3 x TW2864B chips and one TW2865.
These cards are displayed by lspci -nn as
"Softlogic Co., Ltd. SOLO6110 H.264 Video encoder/decoder [9413:6110]"
Bluecherry cards have 4 x TW2864A. According to datasheet register 0xFF
of TW2864B chips contains value 0x6A or 0x6B depending on revision
which being shifted 3 bits right gives value 0x0d.
Existing version of solo6x10 fails on these cards with
[276582.344942] solo6x10 0000:07:00.0: Probing Softlogic 6110
[276582.402151] solo6x10 0000:07:00.0: Could not initialize any techwell chips
[276582.402781] solo6x10: probe of 0000:07:00.0 failed with error -22
Signed-off-by: Anton Sviridenko <anton@corp.bluecherry.net>
Acked-by: Andrey Utkin <andrey_utkin@fastmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Don't populate const array saa7128_regs_ntsc on the stack but insteaed make
it static. Makes the object code smaller and saves nearly 840 bytes
Before:
text data bss dec hex filename
9218 360 0 9578 256a solo6x10-tw28.o
After:
text data bss dec hex filename
8237 504 0 8741 2225 solo6x10-tw28.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Andrey Utkin <andrey_utkin@fastmail.com>
Signed-off-by: Ismael Luceno <ismael@iodev.co.uk>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Declare v4l2_file_operations structure as const as it is only stored
in the fops field of video_device structure. This field is of type
const, so declare v4l2_file_operations structures with similar properties
as const.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJZapWhAAoJEHm+PkMAQRiGKb0IAJM6b7SbWaw69Og7+qiFB+zZ
xp29iXqbE9fPISC6a5BRQV1ONjeDM6opGixGHqGC8Hla6k2IYz25VDNoF8wd0MXN
cz/Ih20vd3C5afxXGe5cTT8lsPAlV0mWXxForlu6j8jPeL62FPfq6RhEkw7AcrYL
yfYy3k3qSdOrrvBdII0WAAUi46UfIs+we9BQgbsMbkHOiqV2K0MOrzKE84Xbgepq
RAy2xg6P4b4+hTx8xTrYc1MXwpnqjRc0oJ08gdmiwW3AOOU7LxYFn7zDkLPWi9Rr
g4x6r4YhBTGxT4wNvovLIiqd9QFs//dMCuPWYwEtTICG48umIqqq24beQ0mvCdg=
=08Ic
-----END PGP SIGNATURE-----
Merge tag 'v4.13-rc1' into patchwork
Linux v4.13-rc1
* tag 'v4.13-rc1': (11136 commits)
Linux v4.13-rc1
random: reorder READ_ONCE() in get_random_uXX
random: suppress spammy warnings about unseeded randomness
replace incorrect strscpy use in FORTIFY_SOURCE
kmod: throttle kmod thread limit
kmod: add test driver to stress test the module loader
MAINTAINERS: give kmod some maintainer love
xtensa: use generic fb.h
fault-inject: add /proc/<pid>/fail-nth
fault-inject: simplify access check for fail-nth
fault-inject: make fail-nth read/write interface symmetric
fault-inject: parse as natural 1-based value for fail-nth write interface
fault-inject: automatically detect the number base for fail-nth write interface
kernel/watchdog.c: use better pr_fmt prefix
MAINTAINERS: move the befs tree to kernel.org
lib/atomic64_test.c: add a test that atomic64_inc_not_zero() returns an int
mm: fix overflow check in expand_upwards()
ubifs: Set double hash cookie also for RENAME_EXCHANGE
ubifs: Massage assert in ubifs_xattr_set() wrt. init_xattrs
ubifs: Don't leak kernel memory to the MTD
...
-----BEGIN PGP SIGNATURE-----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=RtxO
-----END PGP SIGNATURE-----
Merge tag 'media/v4.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- addition of fwnode support at V4L2 core
- addition of a few more SDR formats
- new imx driver to support i.MX6 cameras
- new driver for Qualcon venus codecs
- new I2C sensor drivers: dw9714, max2175, ov13858, ov5640
- new CEC driver: stm32-cec
- some improvements to DVB frontend documentation and a few fixups
- several driver improvements and fixups
* tag 'media/v4.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (361 commits)
[media] media: entity: Catch unbalanced media_pipeline_stop calls
[media] media/uapi/v4l: clarify cropcap/crop/selection behavior
[media] v4l2-ioctl/exynos: fix G/S_SELECTION's type handling
[media] vimc: sen: Declare vimc_sen_video_ops as static
[media] vimc: sca: Add scaler
[media] vimc: deb: Add debayer filter
[media] vimc: Subdevices as modules
[media] vimc: cap: Support several image formats
[media] vimc: sen: Support several image formats
[media] vimc: common: Add vimc_colorimetry_clamp
[media] vimc: common: Add vimc_link_validate
[media] vimc: common: Add vimc_pipeline_s_stream helper
[media] vimc: common: Add vimc_ent_sd_* helper
[media] vimc: Move common code from the core
[media] vimc: sen: Integrate the tpg on the sensor
[media] media: i2c: ov772x: Force use of SCCB protocol
[media] dvb uapi docs: enums are passed by value, not reference
[media] dvb: don't use 'time_t' in event ioctl
[media] media: venus: enable building with COMPILE_TEST
[media] af9013: refactor power control
...
The buffer mode was already implemented in this driver, but it did not work
as expected. This has been fixed now, but it is still deactivated and can
be activated by removing a comment at the begin of the file.
Original code change by Ralph Metzler, modified by Jasmin Jessich and
Daniel Scheller to match Kernel code style.
Signed-off-by: Ralph Metzler <rjkm@metzlerbros.de>
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Jasmin Jessich <jasmin@anw.at>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The semaphore 'i2c_switch_mutex' is used as a simple mutex, so
it should be written as one. Semaphores are going away in the future.
Signed-off-by: Binoy Jayan <binoy.jayan@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The semaphore 'stream_mutex' is used as a simple mutex, so
it should be written as one. Also moving the mutex_[lock/unlock]
to the caller as it is anyway locked at the beginning of the
callee thus avoiding repetition.
Signed-off-by: Binoy Jayan <binoy.jayan@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The semaphore 'cmd_mutex' is used as a simple mutex, so
it should be written as one. Also, replace down with
mutex_destroy to ensure sane state when ngene_stop is
called.
Signed-off-by: Binoy Jayan <binoy.jayan@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
As such macro will check if the expression is true, it may fall through, as
warned:
In file included from ./include/uapi/linux/stddef.h:1:0,
from ./include/linux/stddef.h:4,
from ./include/uapi/linux/posix_types.h:4,
from ./include/uapi/linux/types.h:13,
from ./include/linux/types.h:5,
from ./drivers/media/dvb-core/dvb_frontend.h:35,
from drivers/media/tuners/fc0011.h:4,
from drivers/media/tuners/fc0011.c:20:
drivers/media/tuners/fc0011.c: In function 'fc0011_set_params':
./include/linux/compiler.h:179:22: warning: this statement may fall through [-Wimplicit-fallthrough=]
# define unlikely(x) __builtin_expect(!!(x), 0)
^~~~~~~~~~~~~~~~~~~~~~~~~~
./include/asm-generic/bug.h:109:2: note: in expansion of macro 'unlikely'
unlikely(__ret_warn_on); \
^~~~~~~~
drivers/media/tuners/fc0011.c:344:3: note: in expansion of macro 'WARN_ON'
WARN_ON(1);
^~~~~~~
drivers/media/tuners/fc0011.c:345:2: note: here
case 0:
^~~~
In file included from ./include/uapi/linux/stddef.h:1:0,
from ./include/linux/stddef.h:4,
from ./include/uapi/linux/posix_types.h:4,
from ./include/uapi/linux/types.h:13,
from ./include/linux/types.h:5,
from ./include/linux/list.h:4,
from ./include/linux/module.h:9,
from drivers/media/pci/tw5864/tw5864-video.c:17:
drivers/media/pci/tw5864/tw5864-video.c: In function 'tw5864_fmt_vid_cap':
./include/linux/compiler.h:179:22: warning: this statement may fall through [-Wimplicit-fallthrough=]
# define unlikely(x) __builtin_expect(!!(x), 0)
^~~~~~~~~~~~~~~~~~~~~~~~~~
./include/asm-generic/bug.h:68:2: note: in expansion of macro 'unlikely'
unlikely(__ret_warn_on); \
^~~~~~~~
drivers/media/pci/tw5864/tw5864-video.c:547:3: note: in expansion of macro 'WARN_ON_ONCE'
WARN_ON_ONCE(1);
^~~~~~~~~~~~
drivers/media/pci/tw5864/tw5864-video.c:548:2: note: here
case STD_NTSC:
^~~~
On both cases, it means an error, so, let's return an error
code, to make gcc happy.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Michael Büsch <m@bues.ch>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Side effect: KERN_DEBUG messages aren't written to the kernel log anymore.
This also improves the tda18212_ping reporting a bit so users know that if
pinging wasn't successful, bad things will happen.
Since in module_init_ddbridge() there's no dev yet, pr_info is used
instead.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Reported by smatch:
drivers/media/pci/ddbridge/ddbridge-core.c:1246 input_tasklet() warn: this loop depends on readl() succeeding
drivers/media/pci/ddbridge/ddbridge-core.c:1768 flashio() warn: this loop depends on readl() succeeding
drivers/media/pci/ddbridge/ddbridge-core.c:1788 flashio() warn: this loop depends on readl() succeeding
Fix this by introducing safe_ddbreadl() which will wrap ddbreadl and checks
for all bits set in the return which indicates failure, and return 0 in
that case. Usable as drop-in-replacement in all affected while loops w/o
having to change the logic.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Adds hardware IDs for all Sony CXD-based Cine-cards and MaxA8 devices, also
adds some other yet missing IDs like the Octopus V3, Octopus OEM and
Octopus Mini, as well as cards with unknown/deleted sub-ids.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Properly detect and attach Ports and Flex modules with the Sony CXD28xxER
series demods. This makes newer Cine cards and most DuoFlex C/C2/T/T2 (or
any combination of these systems) work, PCI IDs need to be added though.
Note: This utilises the CXD2841ER demod driver, which requires the changes
from this patch series to properly work. Without those changes, it won't
function properly (if at all).
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Some Flex modules (mostly with anyof C/C2/T/T2 demods based on the Sony
CXD28xxER series) are equipped with an interface named XO2 (which
appears to be the Lattice MachXO2). Add functionality to detect such
links and initialise them, so any tuner module with such an interface can
be used.
This also adds dummy detection for any possible connected module, telling
the user it isn't supported at this very moment.
Also adds i2c_io(), i2c_write() and i2c_write_reg(), all required for the
XO2 handling functionality.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This is a backport of the board control setup from the vendor provided
dddvb driver package, which does additional device initialisation based
on the board_control device info values. Also backports the TS quirk
flags which is used to control setup and usage of the tuner modules
soldered on the bridge cards (e.g. CineCTv7, CineS2 V7, MaxA8 and the
likes).
Functionality originates from ddbridge vendor driver. Permission for
reuse and kernel inclusion was formally granted by Ralph Metzler
<rjkm@metzlerbros.de>.
Cc: Ralph Metzler <rjkm@metzlerbros.de>
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The Sony CXD28xx demods may have other tuner types attached to them (e.g.
NXP TDA18212), so don't mandatorily configure and enable the ASCOT
functionality, but make this conditional by a config flag.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Acked-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Some cards/bridges wrap i2c_gate_ctrl handling with a mutex_lock(). This is
e.g. done in ddbridge to protect against concurrent tuner access with
regards to the dual tuner HW, where concurrent tuner reconfiguration can
result in tuning fails or bad reception quality. When the tuner driver
additionally tries to open the I2C gate (which e.g. the tda18212 driver
does) when the demod already did this, this will lead to a deadlock. This
makes the calls to i2c_gatectrl from the demod driver optional when the
flag is set, leaving this to the tuner driver. For readability reasons and
to not have the check duplicated multiple times, the setup is factored
into cxd2841er_tuner_set().
This commit also updates the netup card driver (which seems to be the only
consumer of the cxd2841er as of now).
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Acked-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This adds detection and activation for STV0367-based tuner hardware (namely
CineCTv6 bridge cards and older DuoFlex CT addon modules). Utilises the
extended stv0367 demod driver.
TDA18212 i2c_client/regmap-api code was originally implemented by
Antti Palosaari <crope@iki.fi> in a variant to update the ddbridge code
from the vendor dddvb package (formal ack for these parts received).
Original patch at [1].
When boards with STV0367 are cold-started, there might be issues with the
I2C gate, causing the TDA18212 detection/probe to fail. For these demods,
a workaround (tuner_tda18212_ping) is implemented which probes the tuner
twice on this hardware constellation which will resolve the problem and
put all components into a working state. Other demod/port types won't be
retried.
[1] https://patchwork.linuxtv.org/patch/25146/
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Adds new i2c_read_regs() function and make i2c_read_reg() wrap into this
with len=1. Required for the tuner_tda18212_ping() and XO2 handling
functions (part of the Sony CXD28xx support patch series).
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The driver may sleep under a spin lock, and the function call path is:
snd_cx18_pcm_hw_free (acquire the lock by spin_lock_irqsave)
vfree --> may sleep
To fix it, the "substream->runtime->dma_area" is passed to a temporary
value, and mark it NULL when holding the lock. The memory is freed by
vfree through the temporary value outside the lock holding.
Signed-off-by: Jia-Ju Bai <baijiaju1990@163.com>
[hans.verkuil@cisco.com: removed unnecessary 'if (dma_area)']
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The driver may sleep under a spin lock, and the function call path is:
snd_ivtv_pcm_hw_free (acquire the lock by spin_lock_irqsave)
vfree --> may sleep
To fix it, the "substream->runtime->dma_area" is passed to a temporary
value, and mark it NULL when holding the lock. The memory is freed by
vfree through the temporary value outside the lock holding.
Signed-off-by: Jia-Ju Bai <baijiaju1990@163.com>
[hans.verkuil@cisco.com: removed unnecessary 'if (dma_area)']
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Avoid a double fetch by reusing the values from the prior transfer.
Originally reported via https://bugzilla.kernel.org/show_bug.cgi?id=195559
Thanks to Pengfei Wang <wpengfeinudt@gmail.com> for reporting.
Signed-off-by: Steven Toth <stoth@kernellabs.com>
Reported-by: Pengfei Wang <wpengfeinudt@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
trivial fix to spelling mistake and add in a white space in
a CX18_ERR error message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Function pci_find_ext_capability() may return 0, which is an invalid
address. In function cobalt_pcie_status_show(), its return value is used
without validation. This patch adds checks to validate the return
address.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Setting initial standard at the top of cx8800_initdev would cause the
first call to cx88_set_tvnorm() to return without programming any
registers (leaving the driver saying it's set to NTSC but the hardware
isn't programmed). Even worse, any subsequent attempt to explicitly
set it to NTSC-M will return success but actually fail to program the
underlying registers unless first changing the standard to something
other than NTSC-M.
Set the initial standard later in the process, and make sure the field
is zero at the beginning to ensure that the call always goes through.
This regression was introduced in the following commit:
commit ccd6f1d488 ("[media] cx88: move width, height and field to core
struct")
Author: Hans Verkuil <hans.verkuil@cisco.com>
[media] cx88: move width, height and field to core struct
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Cc: <stable@vger.kernel.org> # for v3.19 and up
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Replace the copy and the silence ops with the new PCM ops.
The device supports only 1 channel and 8bit sample, so it's always
bytes=frames, and we need no conversion of unit in the callback.
Also, it's a capture stream, thus no silence is needed.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There are two cases here that it does a switch fall through.
Annotate it, in order to shut up gcc warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
On two switches, this driver have unannotated switch
fall through.
in the first case, it falls through a return. On the second
one, it prints undesired log messages on fall through.
Solve that by copying the commands that it should be
running. Gcc will very likely optimize it anyway, so this
sholdn't be causing any harm, and shuts up gcc warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Avoid warnings like those:
drivers/media/pci/ddbridge/ddbridge-core.c: In function 'dvb_input_detach':
drivers/media/pci/ddbridge/ddbridge-core.c:787:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (input->fe) {
^
drivers/media/pci/ddbridge/ddbridge-core.c:792:2: note: here
case 4:
^~~~
...
On several cases, it is just that gcc 7.1 is not capable of
understanding the comment, but on other places, we need an
annotation.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The logic that handles CA_SET_PID is clearly missing a
break: it prints that the command succeeded, but, due to the
missing break, it would be returning -EOPNOTSUPP, as if the
driver weren't supporting such ioctl.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Right now, the driver is doing the right thing for
PVC_ERRORCODE_UNKNOWN and PVC_ERRORCODE_INVALID_CONTROL:
for both, it returns an error code (SAA_ERR_NOT_SUPPORTED).
However, it is printing two error messages instead of one
on those cases.
Fix the logic.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
-----BEGIN PGP SIGNATURE-----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=lbS7
-----END PGP SIGNATURE-----
Merge tag 'hwparam-20170420' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
Pull hw lockdown support from David Howells:
"Annotation of module parameters that configure hardware resources
including ioports, iomem addresses, irq lines and dma channels.
This allows a future patch to prohibit the use of such module
parameters to prevent that hardware from being abused to gain access
to the running kernel image as part of locking the kernel down under
UEFI secure boot conditions.
Annotations are made by changing:
module_param(n, t, p)
module_param_named(n, v, t, p)
module_param_array(n, t, m, p)
to:
module_param_hw(n, t, hwtype, p)
module_param_hw_named(n, v, t, hwtype, p)
module_param_hw_array(n, t, hwtype, m, p)
where the module parameter refers to a hardware setting
hwtype specifies the type of the resource being configured. This can
be one of:
ioport Module parameter configures an I/O port
iomem Module parameter configures an I/O mem address
ioport_or_iomem Module parameter could be either (runtime set)
irq Module parameter configures an I/O port
dma Module parameter configures a DMA channel
dma_addr Module parameter configures a DMA buffer address
other Module parameter configures some other value
Note that the hwtype is compile checked, but not currently stored (the
lockdown code probably won't require it). It is, however, there for
future use.
A bonus is that the hwtype can also be used for grepping.
The intention is for the kernel to ignore or reject attempts to set
annotated module parameters if lockdown is enabled. This applies to
options passed on the boot command line, passed to insmod/modprobe or
direct twiddling in /sys/module/ parameter files.
The module initialisation then needs to handle the parameter not being
set, by (1) giving an error, (2) probing for a value or (3) using a
reasonable default.
What I can't do is just reject a module out of hand because it may
take a hardware setting in the module parameters. Some important
modules, some ipmi stuff for instance, both probe for hardware and
allow hardware to be manually specified; if the driver is aborts with
any error, you don't get any ipmi hardware.
Further, trying to do this entirely in the module initialisation code
doesn't protect against sysfs twiddling.
[!] Note that in and of itself, this series of patches should have no
effect on the the size of the kernel or code execution - that is
left to a patch in the next series to effect. It does mark
annotated kernel parameters with a KERNEL_PARAM_FL_HWPARAM flag in
an already existing field"
* tag 'hwparam-20170420' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs: (38 commits)
Annotate hardware config module parameters in sound/pci/
Annotate hardware config module parameters in sound/oss/
Annotate hardware config module parameters in sound/isa/
Annotate hardware config module parameters in sound/drivers/
Annotate hardware config module parameters in fs/pstore/
Annotate hardware config module parameters in drivers/watchdog/
Annotate hardware config module parameters in drivers/video/
Annotate hardware config module parameters in drivers/tty/
Annotate hardware config module parameters in drivers/staging/vme/
Annotate hardware config module parameters in drivers/staging/speakup/
Annotate hardware config module parameters in drivers/staging/media/
Annotate hardware config module parameters in drivers/scsi/
Annotate hardware config module parameters in drivers/pcmcia/
Annotate hardware config module parameters in drivers/pci/hotplug/
Annotate hardware config module parameters in drivers/parport/
Annotate hardware config module parameters in drivers/net/wireless/
Annotate hardware config module parameters in drivers/net/wan/
Annotate hardware config module parameters in drivers/net/irda/
Annotate hardware config module parameters in drivers/net/hamradio/
Annotate hardware config module parameters in drivers/net/ethernet/
...
When the kernel is running in secure boot mode, we lock down the kernel to
prevent userspace from modifying the running kernel image. Whilst this
includes prohibiting access to things like /dev/mem, it must also prevent
access by means of configuring driver modules in such a way as to cause a
device to access or modify the kernel image.
To this end, annotate module_param* statements that refer to hardware
configuration and indicate for future reference what type of parameter they
specify. The parameter parser in the core sees this information and can
skip such parameters with an error message if the kernel is locked down.
The module initialisation then runs as normal, but just sees whatever the
default values for those parameters is.
Note that we do still need to do the module initialisation because some
drivers have viable defaults set in case parameters aren't specified and
some drivers support automatic configuration (e.g. PNP or PCI) in addition
to manually coded parameters.
This patch annotates drivers in drivers/media/.
Suggested-by: Alan Cox <gnomes@lxorguk.ukuu.org.uk>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
cc: mjpeg-users@lists.sourceforge.net
cc: linux-media@vger.kernel.org
Remove dead code. The following line of code is never reached:
return SAA_OK;
Addresses-Coverity-ID: 114283
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Reviewed-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Declare stv0299_config structures as const as they are only passed as
an argument to the function dvb_attach. dvb_attach
calls its first argument on the rest of its arguments. The first
argument of dvb_attach in the changed cases is stv0299_attach and
the parameter of this function to which the object references are passed
is of type const. So, stv0299_config structures having this property
can be made const.
First line shows the file size before patching and second one shows size
after patching.
text data bss dec hex filename
9572 926 40 10538 292a media/pci/dm1105/dm1105.o
9636 862 40 10538 292a media/pci/dm1105/dm1105.o
15133 5408 0 20541 503d media/pci/ttpci/budget-av.o
15389 5152 0 20541 503d media/pci/ttpci/budget-av.o
15703 2326 36 18065 4691 media/pci/ttpci/budget-ci.o
15767 2262 36 18065 4691 media/pci/ttpci/budget-ci.o
10555 1918 4 12477 30bd drivers/media/pci/ttpci/budget.o
10683 1822 4 12509 30dd drivers/media/pci/ttpci/budget.o
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Declare mb86a16_config structure as const as it is either passed as
an argument to the function dvb_attach or is dereferenced. dvb_attach
calls its first argument on the rest of its arguments. The first argument
of dvb_attach in the changed case is mb86a16_attach and the parameter of
this function to which the object reference is passed is of type
const. So, mb86a16_config structures having this property can be made
const.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Declare mb86a16_config structure as const as it is only passed as
an argument to the function dvb_attach. dvb_attach calls its first
argument on the rest of its arguments. The first argument of
dvb_attach in the changed case is mb86a16_attach and the parameter of
this function to which the object reference is passed is of type
const. So, mb86a16_config structures having this property can be made
const.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Declare nxt200x_config structures as const as they are only passed as
an argument to the function dvb_attach. dvb_attach calls its first
argument on the rest of its arguments. The first argument of
dvb_attach in the changed cases is nxt200x_attach and the parameter of
this function to which the object references are passed is of type
const. So, nxt200x_config structures having this property can be made
const.
File size before:
text data bss dec hex filename
21320 3776 16 25112 6218 saa7134/saa7134-dvb.o
File size after:
text data bss dec hex filename
21384 3744 16 25144 6238 saa7134/saa7134-dvb.o
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use setup_timer() instead of init_timer() to simplify the code.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use setup_timer() instead of init_timer() to simplify the code.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use setup_timer() instead of init_timer() to simplify the code.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Brad Love