This fixes incorrect detection of the second SDVO/HDMI output on G4X, and
extra boot time on pre-G4X.
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
This improves the PLL timings according to the suggestion of the hardware
engineers. This results in some outputs being able to sync that weren't
able to before.
This is part of fixing fd.o bug #17508.
Signed-off-by: Ma Ling <ling.ma@intel.com>
[anholt: cleaned up a couple of redundant comments]
Signed-off-by: Eric Anholt <eric@anholt.net>
The values come from the internal reference spreadsheet on PLL
timing limits for the G4X chipsets.
Part of fixing fd.o bug #17508
Signed-off-by: Ma Ling <ling.ma@intel.com>
[anholt: Cleaned up some whitespace]
Signed-off-by: Eric Anholt <eric@anholt.net>
Later spec investigation has revealed that every 9xx mobile part has
had this register in this format. Also, no non-mobile parts have been shown
to have this register. So make all mobile use the same code, and all
non-mobile use the hack 965 detection.
Signed-off-by: Eric Anholt <eric@anholt.net>
* 'bkl-removal' of git://git.lwn.net/linux-2.6:
Rationalize fasync return values
Move FASYNC bit handling to f_op->fasync()
Use f_lock to protect f_flags
Rename struct file->f_ep_lock
Most fasync implementations do something like:
return fasync_helper(...);
But fasync_helper() will return a positive value at times - a feature used
in at least one place. Thus, a number of other drivers do:
err = fasync_helper(...);
if (err < 0)
return err;
return 0;
In the interests of consistency and more concise code, it makes sense to
map positive return values onto zero where ->fasync() is called.
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
This fixes 2 bugs:
1. the AGP calculation wasn't consistent with the PCI(E) calc for the
RPTR_ADDR registers. This consolidates the writes and fixes it up.
2. The scratch address was being incorrectly calculated, this breaks
it out into a lot more linear steps.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Fix this sparse warning:
drivers/gpu/drm/radeon/r600_cp.c:1811:52: warning: Using plain integer as NULL pointer
drivers/gpu/drm/radeon/radeon_cp.c:1363:52: warning: Using plain integer as NULL pointer
drivers/gpu/drm/radeon/radeon_state.c:1983:61: warning: Using plain integer as NULL pointer
Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This realigns the r600 pci mapping calls with the ati pcigart ones,
fixing the direction and using the correct interface.
Suggested by Jerome Glisse.
Signed-off-by: Dave Airlie <airlied@redhat.com>
the checks weren't updated when RS600 support
was added.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
RS600s are an AMD IGP for Intel CPUs, that look like RS690s from
a lot of perspectives but look like r600s from a memory controller
point of view.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This adds support for 2D/Xv acceleration in the X.org 2D driver,
to the drm. It doesn't yet provide any 3D support hooks.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This uses the same microcode system as the current radeon code.
It should be converted to the new microcode loader I suppose,
though really I need a lot more proof of the worth of me maintaining
firmware blobs externally.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
agp_chipset_flush() is for flushing the intel GMCH write cache via the
IFP, these two uses are for when we're getting the object into the cpu
READ domain, and thus should not be needed. This confused me when I was
getting my head around the code.
With thanks to airlied for helping me check my mental picture of how the
flushes and clflushes are supposed to be used.
Signed-off-by: Owain G. Ainsworth <oga@openbsd.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This was inspired by a patch by Chris Wilson, though none of it applied in any
way due to the debugfs work and I decided to change the formatting of the
new information anyway.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Here we eliminate a few functions in favor of using a single function
to dump from all of the object lists.
Signed-Off-By: Ben Gamari <bgamari@gmail.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The old mechanism to formatting proc files is extremely ugly. The
seq_file API was designed specifically for cases like this and greatly
simplifies the process.
Also, most of the files in /proc really don't belong there. This patch
introduces the infrastructure for putting these into debugfs and exposes
all of the proc files in debugfs as well.
This contains the i915 hooks rewrite as well, to make bisectability better.
Signed-off-by: Ben Gamari <bgamari@gmail.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
On some radeon GPUs this appears to introduce another level of
stability around interacting with the ring.
Its pretty much what fglrx appears to do.
Signed-off-by: Dave Airlie <airlied@redhat.com>
This is usedul when you have multiple cards to figure out which
one is which minor.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Only X86 32-bit uses a different alignment for "unsigned long long"
than it's 64-bit counterpart.
Therefore this compat translation is only correct, and only needed,
when either CONFIG_X86 or CONFIG_IA64.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
In compat mode, the cmdbuf->buf 64-bit address cookie can
potentially be only 32-bit aligned. Dereferencing this as
64-bit causes expensive unaligned traps on platforms like
sparc64.
Use get_unaligned() to fix.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Platforms such as sparc64 have D-cache aliasing issues. We
cannot allow virtual mappings in different contexts to be such
that two cache lines can be loaded for the same backing data.
Updates to one cache line won't be seen by accesses to the other
cache line.
Code in sparc64 and other architectures solve this problem by
making sure that all userland mappings of MAP_SHARED objects have
the same virtual address base. They implement this by keying
off of the page offset, and using that to choose a suitably
consistent virtual address for mmap() requests.
Making things even worse, getting this wrong on sparc64 can result
in hangs during DRM lock acquisition. This is because, at least on
UltraSPARC-III, normal loads consult the D-cache but atomics such
as 'cas' (which is what cmpxchg() is implement using) only consult
the L2 cache. So if a D-cache alias is inserted, the load can
see different data than the atomic, and we'll loop forever because
the atomic compare-and-exchange will never complete successfully.
So to make this all work properly, we need to make sure that the
hash address computed by drm_map_handle() preserves the SHMLBA
relevant bits, and that's what this patch does for _DRM_SHM mappings.
As a historical note, many years ago this bug didn't exist because we
used to just use the low 32-bits of the address as the hash and just
hope for the best. This preserved the SHMLBA bits properly. But when
the hashtab code was added to DRM, this was no longer the case.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The variable 'max_pages' is ambiguous. There are two concepts
of "pages" being used in this function.
First, we have ATI GART pages which are always 4096 bytes.
Then, we have system pages which are of size PAGE_SIZE.
Eliminate the confusion by creating max_ati_pages and
max_real_pages. Calculate and use them as appropriate.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
This allocates a physical surface for the PCI GART table, this way no
matter what other surface configurations exist the GART table will
always be seen by the hardware properly.
We encode the file pointer of the virtual surface allocate using a
special cookie value, called PCIGART_FILE_PRIV. On the last close, we
release that surface.
Just to be doubly safe, we run the pcigart table setup with the main
surface control register clear.
Based upon ideas from David Airlie and Ben Benjamin Herrenschmidt.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
The address needs to be a GART relative address, rather than a PCI
DMA address.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
These are not supposed to be booleans, they are
supposed to be bit masks.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
The memory behind ring_rptr can either be in ioremapped memory
or a vmalloc() normal kernel memory buffer.
However, the code unconditionally uses DRM_{READ,WRITE}32() (and thus
readl() and writel()) to access it.
Basically, if RADEON_IS_AGP then it's ioremap()'d memory else it's
vmalloc'd memory.
Adjust all of the ring_rptr access code as needed.
While we're here, kill the 'scratch' pointer in drm_radeon_private.
It's only used in the one place where it is initialized.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
The buffers mapped by the PCI GART can be written to by the device,
not just read.
For example, this happens via the RB_RPTR writeback on Radeon.
So we can't use PCI_DMA_TODEVICE else we'll get protection faults
on IOMMU platforms.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
The PCI GART table initialization code treats the GART table mapping
unconditionally as a kernel virtual address.
But it could be in the framebuffer, for example, and thus we're
dealing with a PCI MEM space ioremap() cookie. Treating that as a
virtual address is illegal and will crash some system types (such as
sparc64 where the ioremap() return value is actually a physical I/O
address).
So access the area correctly, using gart_info->gart_table_location as
our guide.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
The kernel shouldn't be in the business of telling user space which
driver to load. The kernel defers mapping PCI IDs to module names
to user space and we should do the same for DRI drivers.
And in fact, that's how it does work today. Nothing uses the
dri_library_name attribute, and the attribute is in fact broken.
For intel devices, it falls back to the default behaviour of returning
the kernel module name as the DRI driver name, which doesn't work for
i965 devices. Nobody has ever hit this problem or filed a bug about this.
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Under kernel modesetting, we manage the device at all times, regardless
of VT switching and X servers, so the only decent thing to do is to
claim the PCI device. In that case, we call the suspend/resume hooks
directly from the pci driver hooks instead of the current class device detour.
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
This changes drm_local_map to use a resource_size for its "offset"
member instead of an unsigned long, thus allowing 32-bit machines
with a >32-bit physical address space to be able to store there
their register or framebuffer addresses when those are above 4G,
such as when using a PCI video card on a recent AMCC 440 SoC.
This patch isn't as "trivial" as it sounds: A few functions needed
to have some unsigned long/int changed to resource_size_t and a few
printk's had to be adjusted.
But also, because userspace isn't capable of passing such offsets,
I had to modify drm_find_matching_map() to ignore the offset passed
in for maps of type _DRM_FRAMEBUFFER or _DRM_REGISTERS.
If we ever support multiple _DRM_FRAMEBUFFER or _DRM_REGISTERS maps
for a given device, we might have to change that trick, but I don't
think that happens on any current driver.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Once upon a time, the DRM made the distinction between the drm_map
data structure exchanged with user space and the drm_local_map used
in the kernel.
For some reasons, while the BSD port still has that "feature", the
linux part abused drm_map for kernel internal usage as the local
map only existed as a typedef of the struct drm_map.
This patch fixes it by declaring struct drm_local_map separately
(though its content is currently identical to the userspace variant),
and changing the kernel code to only use that, except when it's a
user<->kernel interface (ie. ioctl).
This allows subsequent changes to the in-kernel format
I've also replaced the use of drm_local_map_t with struct drm_local_map
in a couple of places. Mostly by accident but they are the same (the
former is a typedef of the later) and I have some remote plans and
half finished patch to completely kill the drm_local_map_t typedef
so I left those bits in.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
The DRM uses its own wrappers to obtain resources from PCI devices,
which currently convert the resource_size_t into an unsigned long.
This is broken on 32-bit platforms with >32-bit physical address
space.
This fixes them, along with a few occurences of unsigned long used
to store such a resource in drivers.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Dave Airlie <airlied@linux.ie>
The last 8 fence registers sit at a different offset, so when we went to set
fence number 8 in the lower offset, we instead set PGETBL_CTL, and the GPU
got all sorts of angry at us.
fd.o bug #20567. Easily reproducible by running glxgears and killing it about
6 times.
Signed-off-by: Eric Anholt <eric@anholt.net>
The i915 also uses the fence registers for GPU access to tiled buffers so
we cannot reallocate one whilst it is on the active list. By performing a
LRU scan of the fenced buffers we also avoid waiting the possibility of
waiting on a pinned, or otherwise unusable, buffer.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
We need to check and report if there are no available fences - or else we
spin endlessly waiting for a buffer to magically unpin itself.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
As we may steal the fence register of an unpinned buffer for another,
every time we repin the buffer we need to recheck whether it needs to be
allocated a fence.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
If we wait upon a request and successfully unbind a buffer occupying a
fence register, then that slot will be freed and cause a NULL derefrence
upon rescanning.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
The VGA registers just hit the pipe registers that we already set through
MMIO. This fixes strange colors on resume.
Signed-off-by: Pierre Willenbrock <pierre@pirsoft.de>
Signed-off-by: Eric Anholt <eric@anholt.net>
If userspace passes an object list with the same object appearing more
than once, we end up hitting the BUG_ON() in
i915_gem_object_set_to_gpu_domain() as it gets called a second time
for the same object.
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
This could be triggered by a client asking to emit an irq when the device
wasn't initialized.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
This is done by
1) Wake up lock waiters when we close the master file descriptor.
Not when the master structure is removed, since the latter
requires the waiters themselves to release the refcount on the
master structure -> Deadlock.
2) Send a SIGTERM to all clients waiting for the lock.
Normally these clients will get a SIGPIPE when the X server dies,
but clients may also spin trying to grab the DRM lock, without
getting any sort of notification.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Currently only one waiter is woken up, leaving other waiters
hanging waiting for the DRM lock.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
That return code is for in-kernel use only.
Use EINTR instead.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Impact: standardize IO on cached ops
On modern CPUs it is almost always a bad idea to use non-temporal stores,
as the regression in this commit has shown it:
30d697f: x86: fix performance regression in write() syscall
The kernel simply has no good information about whether using non-temporal
stores is a good idea or not - and trying to add heuristics only increases
complexity and inserts fragility.
The regression on cached write()s took very long to be found - over two
years. So dont take any chances and let the hardware decide how it makes
use of its caches.
The only exception is drivers/gpu/drm/i915/i915_gem.c: there were we are
absolutely sure that another entity (the GPU) will pick up the dirty
data immediately and that the CPU will not touch that data before the
GPU will.
Also, keep the _nocache() primitives to make it easier for people to
experiment with these details. There may be more clear-cut cases where
non-cached copies can be used, outside of filemap.c.
Cc: Salman Qazi <sqazi@google.com>
Cc: Nick Piggin <npiggin@suse.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: enable DMAR by default
xen: disable interrupts early, as start_kernel expects
gpu/drm, x86, PAT: io_mapping_create_wc and resource_size_t
gpu/drm, x86, PAT: Handle io_mapping_create_wc() errors in a clean way
x86, Voyager: fix compile by lifting the degeneracy of phys_cpu_present_map
x86, doc: fix references to Documentation/x86/i386/boot.txt
io_mapping_create_wc can return NULL on error and io_mapping_free() should be
called on one of the error-cleanup path.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Eric Anholt <eric@anholt.net>
Cc: Keith Packard <keithp@keithp.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: cleanup, enable future change
Add a 'total bytes copied' parameter to __copy_from_user_*nocache(),
and update all the callsites.
The parameter is not used yet - architecture code can use it to
more intelligently decide whether the copy should be cached or
non-temporal.
Cc: Salman Qazi <sqazi@google.com>
Cc: Nick Piggin <npiggin@suse.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
However we still have another issue with ioremap_wc not falling back
properly or somehow doing something else stupid, this probably needs
to be tracked down.
Signed-off-by: Dave Airlie <airlied@redhat.com>
edid->revision == 0 should be valid (at least, so the error message
indicates. :) and wikipedia seems to indicate that EDID 1.0 existed.
We can dump the entire check, since edid->revision is a u8, so
it can't ever be less than 0.
Marko reports in RH bz#476735 that his monitor claims to be
EDID 1.0, and therefore hits the check and is stuck at 800x600 because
of it.
Reported-by: Marko Ristola <marko.ristola@kolumbus.fi>
Signed-off-by: Kyle McMartin <kyle@redhat.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Dave Airlie <airlied@linux.ie>
The first time we install a mode, the vblank will be disabled for a pipe
and so drm_vblank_get() in drm_vblank_pre_modeset() will fail. As we
unconditionally call drm_vblank_put() afterwards, the vblank reference
counter becomes unbalanced.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Dave Airlie <airlied@linux.ie>
In some cases we may receive a mode config that has a different
CRTC<->encoder map that the current configuration. In that case, we
need to disable any re-routed encoders before setting the mode,
otherwise they may not pick up the new CRTC (if the output types are
incompatible for example).
Tested-by: Kristian Høgsberg <krh@bitplanet.net>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Dave Airlie <airlied@linux.ie>
We've seen cases in the wild where the VBT sync data is wrong, so add
some code to fix it up in that case, taking care to make sure that the
total is greater than the sync end.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Dave Airlie <airlied@linux.ie>
These are normal; we walk through different values looking for the right
one, so why flood the screen with messages?
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
In the KMS case, enter/leavevt won't fix up the interrupt handler for
us, so we need to do it at suspend/resume time. Make sure we don't fail
the resume if the chip is hung either.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
dev_priv->hw_status_page can be NULL, if i915_gem_retire_requests()
is called from i915_gem_busy_ioctl().
Signed-off-by Karsten Wiese <fzu@wemgehoertderstaat.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
there might be a nicer way to fix this but this is the simplest for now.
Signed-off-by: Pierre Willenbrock <pierre@pirsoft.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The object is dereferenced before the NULL check. Oops.
Fixes http://bugs.freedesktop.org/show_bug.cgi?id=20235
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This ensures that the user gets the latest information from the hardware
on whether the buffer is busy, potentially reducing the working set of objects
that the user chooses.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
In the KMS case, we need to suspend/resume GEM as well. So on suspend, make
sure we idle GEM and stop any new rendering from coming in, and on resume,
re-init the framebuffer and clear the suspended flag.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The problem was that object_set_to_gpu_domain would set the new write_domains
that are getting set by this batchbuffer, then the accumulated flushes required
for all the objects in preparation for this batchbuffer were posted, and the
brand new write domain would get cleared by the flush being posted. Instead,
hang on to the new (or old if we're not changing it) value and set it after
the flush is queued.
Results from this noticably included conformance test failures from reads
shortly after writes (where the new write domain had been lost and thus not
flushed and waited on), but is a suspected cause of hangs in some apps when
a write domain is lost on a buffer that gets reused for instruction or
commmand state.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
While not strictly required, it helped while thinking about the following
change. This change should be invariant.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This fixes a regression reported in bug #12613.
[airlied: not I tweaked the patch slightly and fixed it by etienne did
all the hardwork so gets authorship]
Signed-off-by: etienne <etienne.basset@numericable.fr>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This fixes potential fault at fault time if the object was unreferenced
while the mapping still existed. Now, while the mmap_offset only lives
for the lifetime of the object, the object also stays alive while a vma
exists that needs it.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Need to do this in case the unref ends up doing a free.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Lifted from the DDX modesetting.
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
They used to be different. Now they're identical.
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We need to hold the struct_mutex around pinning and the phys object
operations.
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Check the error paths within intel_pipe_set_base() to first cleanup and
then report back the error.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
We need to skip the connectors with a NULL encoder to match the success
path and avoid an OOPS.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
If we fail to create the ringbuffer, then we need to cleanup the allocated
hws.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
In the case where no EDID data is read from the device, adding the
panel_fixed_mode pointer to the probed modes list causes data corruption.
If the panel_fixed_mode pointer is added to the probed modes list at
init time, a copy of the mode is added again at drm_get_modes() request
time. Then, the panel_fixed_mode pointer is freed because it is seen as
a duplicate mode. Unfortunately, this pointer is still stored and used
in mode_fixup().
Because the panel_fixed_mode data is copied and returned at
drm_get_modes() time, it is unnecessary to add this information at init
time.
Signed-off-by: Steve Aarnio <steve.j.aarnio@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Avoids leaking fbs and associated buffers on release.
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
Tested-by: Tested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
If we fail whilst constructing the fb, then we need to unpin it as well.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
A missing unpin on the error path.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
A missing unpin on the error path.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
A missing unreference and unpin after rejecting the relocation for an
invalid memory domain.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
We failed to unlock the mutex after failing to create the mmap offset.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Set the request alignment to 0, and leave it up to i915_gem_object_pin()
to set the appropriate alignment to match the fence covering the object.
Eric Anholt mentioned that the pinning code is meant to choose the
maximum of the request alignment and that of the fence covering the
object... However currently, the pinning code will only apply the fence
constraints if the supplied alignment is 0.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
The name table should only hold a single reference, so avoid leaking
additional references for secondary calls to flink().
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Lockdep warns that i915_gem_execbuffer() can trigger a page fault (which
takes mmap_sem) while holding dev->struct_mutex, while drm_vm_open()
(which is called with mmap_sem already held) takes dev->struct_mutex.
So this is a potential AB-BA deadlock.
The way that i915_gem_execbuffer() triggers a page fault is by doing
copy_to_user() when returning new buffer offsets back to userspace;
however there is no reason to hold the struct_mutex when doing this
copy, since what is being copied is the contents of an array private to
i915_gem_execbuffer() anyway. So we can fix the potential deadlock (and
get rid of the lockdep warning) by simply moving the copy_to_user()
outside of where struct_mutex is held.
This fixes <http://bugzilla.kernel.org/show_bug.cgi?id=12491>.
Reported-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
A missing unreference if the user calls pin() a second time on a pinned
buffer.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Also spotted by Owain Ainsworth.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Ensure that the object is unreferenced if we fail to allocate during
drm_gem_flink_ioctl().
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Remove the member from the hash table before we free the structure!
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
The C99 specification states in section 6.11.5:
The placement of a storage-class specifier other than at the beginning
of the declaration specifiers in a declaration is an obsolescent
feature.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Submenus of the graphics support "Support for frame buffer devices" and
"Direct Rendering Manager (XFree86 4.1.0 and higher DRI support)" are
broken in half after latest changes for Intel 915 mode setting support.
The DRM subsection is broken because one option is put outside the choice
section it depends on.
The frame buffers part is broken then due to circular dependency. Fix
this by make Intel frame buffers depend on CONFIG_INTEL_AGP.
Kconfigs are broken by d2f5935770
("drm/i915: select framebuffer support automatically").
This is probably not only way to fix this.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Dave Airlie <airlied@linux.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
drivers/gpu/drm/drm_proc.c: In function ‘drm__vma_info’:
drivers/gpu/drm/drm_proc.c:681: warning: format ‘%08lx’ expects type ‘long unsigned int’, but argument 5 has type ‘phys_addr_t’
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The DRI people seem to have a hard time getting these right (see also
commit aeb565dfc3).
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Migration helper.
The i915 driver recently added a 'depends on FB' rule to its
Kconfig entry - which silently turns off DRM_I915 if someone
has a working config but no CONFIG_FB selected, and upgrades
to the latest upstream kernel.
Norbert Preining reported this problem:
Bug-Entry : http://bugzilla.kernel.org/show_bug.cgi?id=12599
Subject : dri /dev node disappeared with 2.6.29-rc1
So change it to "select FB", which auto-selects framebuffer
support. This way the driver keeps working, regardless of
whether FB was enabled before or not.
Kconfig select's of interactive options can be problematic to
dependencies and can cause build breakages - but in this case
it's safe because it's a leaf entry with no dependencies of its
own.
( There is some minor circular dependency fallout as FB_I810
and FB_INTEL also used 'depends on FB' constructs - update
those to "select FB" too. )
Reported-by: Norbert Preining <preining@logic.at>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Dave Airlie <airlied@linux.ie>
As discussed in the long thread about vblank related timeouts, it turns out
GM45 has different frame count registers than previous chips. This patch
adds support for them, which prevents us from waiting on really stale
sequence values in drm_wait_vblank (which rather than returning immediately
ends up timing out or getting interrupted).
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Dave Airlie <airlied@linux.ie>
In dc1336ff4f (set vblank enable flag correctly
across IRQ uninstall), we made sure drivers that uninstall their interrupt
handler set the vblank enabled flag correctly, so that when interrupts are
re-enabled, vblank interrupts & counts work as expected. However I missed the
last_vblank field: it needs to be updated as well, otherwise, at the next
drm_update_vblank_count we'll end up comparing a current count to a stale
one (the last one captured by the disable function), which may trigger the
wraparound handling, leading to a jumpy counter and hangs in drm_wait_vblank.
The jumpy counter can prevent the DRM_WAIT_ON from returning success if the
difference between the current count and the requested count is greater than
2^23, leading to timeouts or hangs, if the ioctl is restarted in a loop (as
is the case in libdrm < 2.4.4).
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Acked-by: Michel Dänzer <michel@daenzer.net>
Tested-by: Timo Aaltonen <tjaalton@cc.hut.fi>
Signed-off-by: Dave Airlie <airlied@redhat.com>
If we failed to allocate a new fence register we would return
VM_FAULT_SIGBUS without relinquishing the lock.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Getting an unknown get/setparam used to be more significant back when they
didn't change much. However, now that we're in the git world we're using
them instead of a monotonic version number to signal feature availability,
so clients ask about unknown params on older kernels more often.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
The Apple Mac Mini falsely reports LVDS. Use DMI to check whether we
are running on a Mac Mini, and skip LVDS initialization if that proves
to be the case.
Signed-off-by: Paul Collins <paul@ondioline.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Pull in an update from the 2D driver (hopefully the last one, future work
should be done here and pulled back into xf86-video-intel as needed).
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Cleanup the object reference on the error paths.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Adds code to set up fence registers at execbuf time on pre-965 chips as
necessary. Also fixes up a few bugs in the pre-965 tile register support
(get_order != ffs). The number of fences available to the kernel defaults
to the hw limit minus 3 (for legacy X front/back/depth), but a new parameter
allows userspace to override that as needed.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Previously, the caller would continue along without knowing that the
function failed, resulting in potential mis-rendering. Right now vm_fault
just returns SIGBUS in that case, and we may need to disable signal handling
to avoid that happening.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
We'd love to just be using PAT, but even on chips with PAT it gets disabled
sometimes due to an errata. It would probably be better to have pat_enabled
exported and only bother with this when !pat_enabled.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
This saves startup time from probing SDVO, and saves setting up HDMI outputs
on G4X devices that don't have them.
Signed-off-by: Dave Airlie <airlied@linux.ie>
The mmap_region() code would temporarily set the VM_ACCOUNT flag for
anonymous shared mappings just to inform shmem_zero_setup() that it
should enable accounting for the resulting shm object. It would then
clear the flag after calling ->mmap (for the /dev/zero case) or doing
shmem_zero_setup() (for the MAP_ANON case).
This just resulted in vma merge issues, but also made for just
unnecessary confusion. Use the already-existing VM_NORESERVE flag for
this instead, and let shmem_{zero|file}_setup() just figure it out from
that.
This also happens to make it obvious that the new DRI2 GEM layer uses a
non-reserving backing store for its object allocation - which is quite
possibly not intentional. But since I didn't want to change semantics
in this patch, I left it alone, and just updated the caller to use the
new flag semantics.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Schedule a vblank signal, kill the process, and we'll go walking over freed
memory. Given that no open-source userland exists using this, nor have I
ever heard of a consumer, just let this code die.
Signed-off-by: Eric Anholt <eric@anholt.net>
Requested-by: Linus Torvalds <torvalds@linux-foundation.org>
Acked-by: Dave Airlie <airlied@linux.ie>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
i2c: Warn on deprecated binding model use
eeprom: More consistent symbol names
eeprom: Move 93cx6 eeprom driver to /drivers/misc/eeprom
spi: Move at25 (for SPI eeproms) to /drivers/misc/eeprom
i2c: Move old eeprom driver to /drivers/misc/eeprom
i2c: Move at24 to drivers/misc/eeprom
i2c: Quilt tree has moved
i2c: Delete many unused adapter IDs
i2c: Delete 10 unused driver IDs
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/i915: Fix cursor physical address choice to match the 2D driver.
drm: stash AGP include under the do-we-have-AGP ifdef
drm: don't whine about not reading EDID data
drm/i915: hook up LVDS DPMS property
drm/i915: remove unnecessary debug output in KMS init
i915: fix freeing path for gem phys objects.
drm: create mode_config idr lock
drm: fix leak of device mappings since multi-master changes.
Use '%zu' to print out a size_t variable, not '%d'. Another case of the
"let's keep at least Linus' defconfig compile warningless" rule.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This fixes the MIPS with DRM build.
Signed-off-by: Eric Anholt <eric@anholt.net>
Tested-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Make this message a little quieter, since it's common and not necessarily
indicative of a problem.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The LVDS output supports DPMS calls, but we never hooked up the property code,
so set property calls didn't actually do anything. Implement a set_property
callback for the LVDS output so that the right thing happens.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Create a separate mode_config IDR lock for simplicity. The core DRM
config structures (connector, mode, etc. lists) are still protected by
the mode_config mutex, but the CRTC IDR (used for the various identifier
IDs) is now protected by the mode_config idr_mutex. Simplifies the
locking a bit and removes a warning.
All objects are protected by the config mutex, we may in the future,
split the object further to have reference counts.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Device maps now contain a link to the master that created them, so
when cleaning up the master, remove any maps that are connected to it.
Also delete any remaining maps at driver unload time.
Signed-off-by: Dave Airlie <airlied@redhat.com>
This is an initial patch to do support for objects which needs physical
contiguous main ram, cursors and overlay registers on older chipsets.
These objects are bound on cursor bin, like pinning, and we copy
the data to/from the backing store object into the real one on attach/detach.
notes:
possible over the top in attach/detach operations.
no overlay support yet.
Signed-off-by: Dave Airlie <airlied@redhat.com>
The detected fixed panel mode really is preferred, so mark it as such and
add it to the LVDS connector mode list.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
When mode setting is first initialized, the driver will call into
drm_helper_initial_config() to set up an initial output and framebuffer
configuration. This routine is responsible for probing the available
connectors, encoders, and crtcs, looking for modes and putting together
something reasonable (where reasonable is defined as "allows kernel
messages to be visible on as many displays as possible").
However, the code was a bit too aggressive in setting default modes when
none were found on a given connector. Even if some connectors had modes,
any connectors found lacking modes would have the default 800x600 mode added
to their mode list, which in some cases could cause problems later down the
line. In my case, the LVDS was perfectly available, but the initial config
code added 800x600 modes to both of the detected but unavailable HDMI
connectors (which are on my non-existent docking station). This ended up
preventing later code from setting a mode on my LVDS, which is bad.
This patch fixes that behavior by making the initial config code walk
through the connectors first, counting the available modes, before it decides
to add any default modes to a possibly connected output. It also fixes the
logic in drm_target_preferred() that was causing zeroed out modes to be set
as the preferred mode for a given connector, even if no modes were available.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
If we are running DRI1 userspace, we really need to set the sarea up properly.
thanks to Richard for finding/testing this.
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
In the absence of kernel mode setting, many drivers disable IRQs across VT
switch. The core DRM vblank code is missing a check for this case however;
even after IRQ disable, the vblank code will still have the vblank_enabled
flag set, so unless we track the fact that they're disabled at IRQ uninstall
time, when we VT switch back in we won't actually re-enable them, which means
any apps waiting on vblank before the switch will hang.
This patch does that and also adds a sanity check to the wait condition to
look for the irq_enabled flag in general, as well as adding a wakeup to the
IRQ uninstall path.
Fixes fdo bug #18879 with compiz hangs at VT switch.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
In some cases userland may be confused and try to wait on vblank events from
pipes that aren't actually enabled. We shouldn't allow this, so return
-EINVAL if the pipe isn't on.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
This is ported directly from the userland 2D driver code. The HDMI audio bits
aren't hooked up yet.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
We also didn't track the cursor bo before and would leak a reference
when the cursor image was change.
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
This avoids a BUG_ON in the enter_vt path due to objects being in the GTT
when we shouldn't have ever let them be (as we're not supposed to touch the
device during that time).
This was triggered by a change in the 2D driver to use the GTT mapping of
objects after pinning them to improve software fallback performance.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Several subsystem open handlers dereference the fops_get() return value
without checking it for nullness. This opens a race condition between the
open handler and module unloading.
A module can be marked as being unloaded (MODULE_STATE_GOING) before its
exit function is called and gets the chance to unregister the driver.
During that window open handlers can still be called, and fops_get() will
fail in try_module_get() and return a NULL pointer.
This change checks the fops_get() return value and returns -ENODEV if NULL.
Reported-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Signed-off-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Acked-by: Takashi Iwai <tiwai@suse.de>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Dave Airlie <airlied@linux.ie>
Acked-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
devname needs to be allocated before the irq is installed, so the
irq routines get the correct name in /proc.
Also check the return value from the AGP init function, and
fixup the exit points.
Signed-off-by: Dave Airlie <airlied@redhat.com>
The error path for object list being null is in the second goto target.
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
This showed up in logs where people had a hung chip, so pinning was blocked
on the chip unpinning other buffers, and the X Server took its scheduler
signal during that time.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
This removes the requirement for user space to pin a buffer before
setting a mode that is backed by the pixels from that buffer.
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Fix this sparse warning:
drivers/gpu/drm/i915/intel_fb.c:417:5: warning: symbol 'intelfb_panic' was not declared. Should it be static?
Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Thanks to Hannes Eder for pointing out that this code was dead according to
sparse.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Move 'extern'-decls from "intel_dvo.c" to "dvo.h", as "dvo.h" is
included by and only by files where the symbols are either defined or
used.
Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Dave Airlie <airlied@linux.ie>
We haven't seen this in practice, but it was visible when looking at a bug
report from when i915_gem_evict_everything() was broken and would always
return error.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
This is required by the display plane, and fixes 1400x1050 laptop displays.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The replace fb ioctl replaces the backing buffer object for a modesetting
framebuffer object. This can be acheived by just creating a new
framebuffer backed by the new buffer object, setting that for the crtcs
in question and then removing the old framebuffer object.
Signed-off-by: Kristian Hogsberg <krh@redhat.com>
Acked-by: Jakob Bornecrantz <jakob@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The initially merged modesetting API has some uglies in it, this
cleans up the struct members and ioctl ordering for initial submission.
It also removes the unneeded hotplug infrastructure.
airlied:- I've pulled this patch in from git modesetting-gem tree.
Signed-off-by: Dave Airlie <airlied@redhat.com>
the calling function doesn't call this function unless one of the two
states that sets the value is true.
Signed-off-by: Dave Airlie <airlied@redhat.com>
This commit adds i915 driver support for the DRM mode setting APIs.
Currently, VGA, LVDS, SDVO DVI & VGA, TV and DVO LVDS outputs are
supported. HDMI, DisplayPort and additional SDVO output support will
follow.
Support for the mode setting code is controlled by the new 'modeset'
module option. A new config option, CONFIG_DRM_I915_KMS controls the
default behavior, and whether a PCI ID list is built into the module for
use by user level module utilities.
Note that if mode setting is enabled, user level drivers that access
display registers directly or that don't use the kernel graphics memory
manager will likely corrupt kernel graphics memory, disrupt output
configuration (possibly leading to hangs and/or blank displays), and
prevent panic/oops messages from appearing. So use caution when
enabling this code; be sure your user level code supports the new
interfaces.
A new SysRq key, 'g', provides emergency support for switching back to
the kernel's framebuffer console; which is useful for testing.
Co-authors: Dave Airlie <airlied@linux.ie>, Hong Liu <hong.liu@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Add mode setting support to the DRM layer.
This is a fairly big chunk of work that allows DRM drivers to provide
full output control and configuration capabilities to userspace. It was
motivated by several factors:
- the fb layer's APIs aren't suited for anything but simple
configurations
- coordination between the fb layer, DRM layer, and various userspace
drivers is poor to non-existent (radeonfb excepted)
- user level mode setting drivers makes displaying panic & oops
messages more difficult
- suspend/resume of graphics state is possible in many more
configurations with kernel level support
This commit just adds the core DRM part of the mode setting APIs.
Driver specific commits using these new structure and APIs will follow.
Co-authors: Jesse Barnes <jbarnes@virtuousgeek.org>, Jakob Bornecrantz <jakob@tungstengraphics.com>
Contributors: Alan Hourihane <alanh@tungstengraphics.com>, Maarten Maathuis <madman2003@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Use the new core GEM object mapping code to allow GTT mapping of GEM
objects on i915. The fault handler will make sure a fence register is
allocated too, if the object in question is tiled.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Add core support for mapping of GEM objects. Drivers should provide a
vm_operations_struct if they want to support page faulting of objects.
The code for handling GEM object offsets was taken from TTM, which was
written by Thomas Hellström.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
...so drm_getunique() is trying to copy some uninitialized data to
userspace. The ECX register contains the number of words that are
left to copy -- so there are 5 * 4 = 20 bytes left. The offset of the
first uninitialized byte (counting from the start of the string) is
also 20 (i.e. 0xf65d2294&((1 << 5)-1) == 20). So somebody tried to
copy 40 bytes when the string was only 19 long.
In drm_set_busid() we have this code:
dev->unique_len = 40;
dev->unique = drm_alloc(dev->unique_len + 1, DRM_MEM_DRIVER);
...
len = snprintf(dev->unique, dev->unique_len, pci:%04x:%02x:%02x.%d",
...so it seems that dev->unique is never updated to reflect the
actual length of the string. The remaining bytes (20 in this case)
are random uninitialized bytes that are copied into userspace.
This patch fixes the problem by setting dev->unique_len after the
snprintf().
airlied- I've had to fix this up to store the alloced size so
we have it for drm_free later.
Reported-by: Sitsofe Wheeler <sitsofe@yahoo.com>
Signed-off-by: Vegard Nossum <vegardno@thuin.ifi.uio.no>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This is step one towards having multiple masters sharing a drm
device in order to get fast-user-switching to work.
It splits out the information associated with the drm master
into a separate kref counted structure, and allocates this when
a master opens the device node. It also allows the current master
to abdicate (say while VT switched), and a new master to take over
the hardware.
It moves the Intel and radeon drivers to using the sarea from
within the new master structures.
Signed-off-by: Dave Airlie <airlied@redhat.com>
The current sub-module unload exit path is a mess, it tries
to abuse the idr. Just keep a list of devices per driver struct
and free them in-order on rmmod.
Signed-off-by: Dave Airlie <airlied@redhat.com>
This check was introduced with the logic the wrong way around.
Fixes regression: http://bugzilla.kernel.org/show_bug.cgi?id=12216
Tested-by: François Valenduc <francois.valenduc@tvcablenet.be>
Signed-off-by: Dave Airlie <airlied@redhat.com>
On PAE systems, GEM allocates pages using shmem, and passes these
pages to be bound into AGP, however the AGP interfaces + the x86
set_memory interfaces all take unsigned long not dma_addr_t.
The initial fix for this was a mess, so we need to do this correctly
for 2.6.29.
Signed-off-by: Dave Airlie <airlied@redhat.com>
These buffers don't have active rendering still occurring to them, they just
need either a flush to be emitted or a retire_requests to occur so that we
notice they're done. Return unbusy so that one of the two occurs. The two
expected consumers of this interface (OpenGL and libdrm_intel BO cache) both
want this behavior.
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Since applying the fix suggested by the errata (disabling MSI), we've had
issues with interrupts being stuck on despite IIR being 0 on GM965 hardware.
Most reporters of the issue have confirmed that turning MSI back on fixes
things, and given the difficulties experienced in getting reliable MSI working
on Linux, it's believable that the errata was about software issues and not
actual hardware issues.
Signed-off-by: Dave Airlie <airlied@redhat.com>
It's only for flushing caches appropriately for GTT access, not for actually
getting it there. Prevents potential smashing of cpu read/write domains on
unbound objects.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
If we fail to pin all of the buffers in an execbuffer request, go through
and clear the GTT and try again to see if its just a matter of fragmentation
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This eliminates the dev_set_domain function and just in-lines it
where its used, with the goal of moving the manipulation and use of
invalidate_domains and flush_domains closer together. This also
avoids calling add_request unless some domain has been flushed.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Now that the CPU and GTT domain operations are isolated to their own
functions, the previously general-purpose set_domain function is now used
only to set GPU domains. It also has no failure cases, which is important as
this eliminates any possible interruption of the computation of new object
domains and subsequent emmission of the flushing instructions into the ring.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This fixes several domain management bugs, including potential lack of cache
invalidation for pread, potential failure to wait for set_domain(CPU, 0),
and more, along with producing more intelligible code.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This fixes failure to flush caches in the relocation update path, and
failure to wait in the set_domain ioctl, each of which could lead to incorrect
rendering.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Otherwise, we would leave the objects in an inconsistent state, such as
write_domain == 0 but on the flushing list.
Signed-off-by: Dave Airlie <airlied@redhat.com>
obj_priv->write_domain is "write domain if the GPU went idle now", not
"write domain at this moment." By postponing the clear, we confused the
concept, required more storage, and potentially emitted more flushes than
are required.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This fixes readpixels and buffer corruption when swapped out and in by
disabling tiling on them.
Now that we know that the bit 17 mode isn't just a mistake of older chipsets,
we'll need to work on a clever fix so that we can get the performance of
tiling on these chipsets, but that will require intrusive changes targeted
at the next kernel release, not this one.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
drivers/gpu/drm/i915/i915_irq.c: In function 'i915_disable_pipestat':
drivers/gpu/drm/i915/i915_irq.c:101: warning: control may reach end of non-void function 'i915_pipestat' being inlined
Cc: Dave Airlie <airlied@linux.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It fixes suspend/resume failure of xf86-video-intel dri2
branch. As dri2 branch doesn't call I830DRIResume() to restore
hardware status page anymore, we need to preserve
this register across suspend/resume.
Signed-off-by: Peng Li <peng.li@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
drm vblank initialization keeps track of the changes in driver-supplied
frame counts across vt switch and mode setting, but only if you let it by
not tearing down the drm vblank structure.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Before we had the notion of pinning objects, we had a kludge around to make
sure all of the objects were still resident in the GTT before we committed
to executing a batch buffer. We don't need this any longer, and it sticks an
error return in the middle of object domain computations that must be
associated with a subsequent flush/invalidate emmission into the ring.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Because we write pipestat before iir, it's possible that a pipestat
interrupt will occur between the pipestat write and the iir write. This
leaves pipestat with an interrupt status not visible in iir. This may cause
an interrupt flood as we never clear the pipestat event.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The old code was wandering through the active list looking for pinned
buffers; there may be other pinned buffers around. Fortunately, we keep a
count of the total amount of pinned memory and can use that instead.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Instead, just warn that bad things are happening and do our best to clean up
the mess without the GPU's help.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The IMR masking was a technique recommended for avoiding getting stuck with
no interrupts generated again in MSI mode. It kept new IIR bits from getting
set between the IIR read and the IIR write, which would have otherwise
prevented an MSI from ever getting generated again. However, this caused a
problem for vblank as the IMR mask would keep the pipe event interrupt from
getting reflected in IIR, even after the IMR mask was brought back down.
Instead, just check the state of IIR after we ack the interrupts we're going
to handle, and restart if we didn't get IIR all the way to zero.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The pipestat fields affect reporting of all vblank-related interrupts, so we
have to reset them during the irq_handler, and while enabling vblank
interrupts. Otherwise, if a pipe status field had been set to non-zero
before enabling reporting, we would never see an interrupt again.
This patch adds i915_enable_pipestat and i915_disable_pipestat to abstract
out the steps needed to change the reported interrupts.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Addresses in the hardware status page below index 0x20 are reserved for use
by the hardware. The legacy breadcrumb was sitting at index 5. Move it to
index 0x21, and make sure everyone uses the defined value instead of
hard-coded constants.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
This fixes hangs on 855-class hardware by avoiding double attachment of the
driver due to the stub second head device having the same pci id as the real
device.
Other DRM drivers probably want this treatment as well, but I'm applying it
just to this one for safety. But we should clean up the drm_pciids.h mess
now so that each driver has its own pci id list header in its own directory.
Lets do that in the next release.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Now that the radeon driver has suspend/resume functions, it needs to map its
registers at load time or it will likely crash if a suspend operation occurs
before the driver has been initialized.
This patch moves the register mapping code from firstopen to load and makes
the mapping into a _DRM_DRIVER one so that the core won't remove it at
lastclose time.
Fixes (at least partially) kernel bz #11891.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Dave Airlie <airlied@linux.ie>
It's not used in any other drivers, and doesn't look like it will be from
drm.git master.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
When userland detected that this ioctl was supported (by version number check),
it used it in a racy way -- dispatch delayed swap, wait for vblank, continue
rendering. As there was no mechanism for it to wait for the swap to finish,
sometimes it would render before the swap and garbage would be displayed on
the screen.
By removing the ioctl and returning -EINVAL, userland returns to its previous,
correct rendering path of waiting for a vblank then dispatching a swap. The
only path that could have used this ioctl correctly was page flipping, which
relied on only one client running and emitting wait-for-vblank-before-rendering
in the command stream. That path also falls back correctly, at the performance
cost of not being able to queue up rendering before the flip occurs.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
This probably just means the chipset doesn't support MSI, which is fine.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
This could return early when reading after writing a buffer, if somebody
had already put it on the flushing list (write domains are 0, but still
active), leading to glReadPixels failure.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
This corresponds to the setup of the sarea pointers in DMA initialization,
though neither is exactly the point at which the sarea is set up or torn down.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
This register is set by the 2D driver to prevent lockups, and so it needs to
be preserved across suspend/resume too. This makes my X200s work.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
* 'io-mappings-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
io mapping: clean up #ifdefs
io mapping: improve documentation
i915: use io-mapping interfaces instead of a variety of mapping kludges
resources: add io-mapping functions to dynamically map large device apertures
x86: add iomap_atomic*()/iounmap_atomic() on 32-bit using fixmaps
* 'drm-next' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
i915: Add GEM ioctl to get available aperture size.
drm/radeon: fixup further bus mastering confusion.
build fix: CONFIG_DRM_I915=y && CONFIG_ACPI=n
This will let userland know when to submit its batchbuffers, before they get
too big to fit in the aperture.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
As it is, all instances of ->release() for files that have ->fasync()
need to remember to evict file from fasync lists; forgetting that
creates a hole and we actually have a bunch that *does* forget.
So let's keep our lives simple - let __fput() check FASYNC in
file->f_flags and call ->fasync() there if it's been set. And lose that
crap in ->release() instances - leaving it there is still valid, but we
don't have to bother anymore.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Impact: optimize/clean-up the IO mapping implementation of the i915 DRM driver
Switch the i915 device aperture mapping to the io-mapping interface, taking
advantage of the cleaner API to extend it across all of the mapping uses,
including both pwrite and relocation updates.
This dramatically improves performance on 64-bit kernels which were using
the same slow path as 32-bit non-HIGHMEM kernels prior to this patch.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
drivers/gpu/drm/i915/i915_opregion.c:340: error: implicit declaration of function ‘register_acpi_notifier’
drivers/gpu/drm/i915/i915_opregion.c:361: error: implicit declaration of function ‘unregister_acpi_notifier’
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'drm-next' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm: Avoid oops in DRM_IOCTL_RM_DRAW if a bad handle is supplied.
drm: Add 32-bit compatibility for DRM_IOCTL_UPDATE_DRAW.
drm/i915: use pipes, not planes to label vblank data
drm/i915: hold dev->struct_mutex and DRM lock during vblank ring operations
i915: Fix format string warnings on x86-64.
i915: Don't dereference HWS in /proc debug files when it isn't initialized.
i915: Enable IMR passthrough of vblank events before enabling it in pipestat.
drm: Remove two leaks of vblank reference count in error paths.
drm: fix leak of cliprects in drm_rmdraw()
i915: Disable MSI on GM965 (errata says it doesn't work)
drm: Set cliprects to NULL when changing drawable to having 0 cliprects.
i915: Protect vblank IRQ reg access with spinlock
This fixes vblank support for a 32-bit X Server on a 64-bit kernel.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
vblank in the kernel is far simpler if it deals with pipes instead of
planes, so we're changing both user and kernel side.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
To synchronize clip lists with the X server, the DRM lock must be held while
looking at drawable clip lists. To synchronize with other ring access, the
ring mutex must be held while inserting commands into the ring. Failure to
do the first resulted in easy visual corruption when moving windows, and the
second could have corrupted the ring with DRI2.
Grabbing the DRM lock involves using the DRM tasklet mechanism, grabbing the
ring mutex means potentially sleeping. Deal with both of these by always
running the tasklet from a work handler.
Also, protect from clip list changes since the vblank request was queued by
making sure the window has at least one rectangle while looking inside,
preventing oopses .
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Otherwise, if we lost the race, the pipestat bit would be set without being
reflected in IIR, and we would never clear the pipestat bit so the pipe
event would never be generated again, and all vblank waits would time out.
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
If the failing paths were hit, the vblank IRQ would never get turned off
again.
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Current Intel errata for the GM965 says that using MSI may cause interrupts
to be delayed or lost. The only workaround offered is to not use it.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This avoids setting the cliprects pointer to a zero-sized allocation.
Signed-off-by: Zhenyu Wang <zhenyu.z.wang@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This uses the same spinlock as the user_irq code as it shares the same
register, ensuring that interrupt registers are updated atomically.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We're trying to keep the !CONFIG_SHMEM tiny-shmem.c (using ramfs without
swap) in synch with CONFIG_SHMEM shmem.c (and mpm is preparing patches
to combine them). I was glad to see EXPORT_SYMBOL_GPL(shmem_file_setup)
go into shmem.c, but why not support DRM-GEM when !CONFIG_SHMEM too?
But caution says still depend on MMU, since !CONFIG_MMU is.. different.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Acked-by: Matt Mackall <mpm@selenic.com>
Acked-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
commit 9b7530cc32 ("i915: cleanup coding
horrors in i915_gem_gtt_pwrite()")
broke the i386 build for CONFIG_HIGHMEM=y.
Caught by automatic testing http://www.tglx.de/autoqa-logs/000137-0006-0001.log
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
[ My bad. It's the same patch I sent out earlier, nobody noticed then either.. ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Yes, this will probably be switched over to a cleaner model anyway, but
in the meantime I don't want to see the 'unused variable' warnings that
come from the disgusting #ifdef code. Make the special case be a nice
inlien function of its own, clean up the code, and make the warning go
away.
I wish people didn't write code that gets (valid) warnings from the
compiler, but I'll limit my fixes to code that I actually care about (in
this case just because I see the warning and it annoys me).
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use "%zd" for size_t, and make sure to have a space between the numbers
instead of depending on the field width.
I don't like warnings in my default targeted build.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Olaf Kirch noticed that the i915_set_status_page() function of the i915
kernel driver calls ioremap with an address offset that is supplied by
userspace via ioctl. The function zeroes the mapped memory via memset
and tells the hardware about the address. Turns out that access to that
ioctl is not restricted to root so users could probably exploit that to
do nasty things. We haven't tried to write actual exploit code though.
It only affects the Intel G33 series and newer.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Someone noticed these registers moved around for later chips,
so we redo the codepaths per-chip. PCIE chips don't appear to
require explicit enables.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Fixes tiling swizzling mode failures that manifest in glReadPixels().
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
At leavevt and lastclose time, cancel any pending retire work handler
invocation, and keep the retire work handler from requeuing itself if it is
currently running.
This patch restructures i915_gem_idle to perform all of these tasks instead
of having both leavevt and lastclose call a sequence of functions.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This should improve performance by avoiding uncached reads by the CPU (the
point of having a status page), and may improve stability. This patch only
affects G33, GM45 and G45 chips as those are the only ones using GTT-based
HWS mappings.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
G45 appears quite sensitive to ring initialization register writes,
sometimes leaving the HEAD register with the START register contents. Check
to make sure HEAD is reset correctly when START is written, and fix it up,
screaming loudly.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Dwords 0 through 0x1f are reserved for use by the hardware. Move the GEM
breadcrumb from 0x10 to 0x20 to keep out of this area.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Like the last patch but adds a macro to get at the irq value instead of
dereferencing pdev directly. Should make things easier for the BSD guys and
if we ever support non-PCI devices.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Fixes failure to map the ringbuffer when PAT tells us we don't get to do
uncached on something that's already mapped WC, or something along those lines.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Fixes bad software fallback rendering in Mesa in dual-channel configurations.
d9a2470012588dc5313a5ac8bb2f03575af00e99
Signed-off-by: Dave Airlie <airlied@redhat.com>
We fail ioctls that depend on the sarea_priv with EINVAL.
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
In the conversion for GEM, we had stopped using the hardware lock to protect
ring usage, since it was all internal to the DRM now. However, some paths
weren't converted to using struct_mutex to prevent multiple threads from
concurrently working on the ring, in particular between the vblank swap handler
and ioctls.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
GEM allows the creation of persistent buffer objects accessible by the
graphics device through new ioctls for managing execution of commands on the
device. The userland API is almost entirely driver-specific to ensure that
any driver building on this model can easily map the interface to individual
driver requirements.
GEM is used by the 2d driver for managing its internal state allocations and
will be used for pixmap storage to reduce memory consumption and enable
zero-copy GLX_EXT_texture_from_pixmap, and in the 3d driver is used to enable
GL_EXT_framebuffer_object and GL_ARB_pixel_buffer_object.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Previously, drivers supporting vblank interrupt waits would run the interrupt
all the time, or all the time that any 3d client was running, preventing the
CPU from sleeping for long when the system was otherwise idle. Now, interrupts
are disabled any time that no client is waiting on a vblank event. The new
method uses vblank counters on the chipsets when the interrupts are turned
off, rather than counting interrupts, so that we can continue to present
accurate vblank numbers.
Co-author: Michel Dänzer <michel@tungstengraphics.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Wrap access to task credentials so that they can be separated more easily from
the task_struct during the introduction of COW creds.
Change most current->(|e|s|fs)[ug]id to current_(|e|s|fs)[ug]id().
Change some task->e?[ug]id to task_e?[ug]id(). In some places it makes more
sense to use RCU directly rather than a convenient wrapper; these will be
addressed by later patches.
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: James Morris <jmorris@namei.org>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Signed-off-by: David Airlie <airlied@redhat.com>
Author: Zhenyu Wang <zhenyu.z.wang@intel.com>
i915: official name for GM45 chipset
Signed-off-by: Zhenyu Wang <zhenyu.z.wang@intel.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
[Patch against drm-next. Consider this a trial balloon for our new Linux
development model.]
This is a big chunk of code. Separating it out makes it easier to change
without churn on the main i915_drv.c file (and there will be churn as we
fix bugs and add things like kernel mode setting). Also makes it easier
to share this file with BSD.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This adds the support necessary for allowing ACPI backlight control to
work on some newer Intel-based graphics systems. Tested on Thinkpad T61
and HP 2510p hardware.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Some chips were unstable with repeated setup/teardown of the hardware status
page.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Previous attempts at interrupt mitigation had been foiled by i915_wait_irq's
failure to update the sarea seqno value when the status page indicated that
the seqno had already been passed. MSI support has been seen to cut CPU
costs by up to 40% in some workloads by avoiding other expensive interrupt
handlers for frequent graphics interrupts.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
It is already correctly detected by the kernel for use in suspend/resume.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The driver can know what hardware requires MI_BATCH_BUFFER vs
MI_BATCH_BUFFER_START; there's no reason to let user mode configure this.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Fix a pointer cast warning in the SIS DRM code.
This was introduced in patch ce65a44de0.
Signed-off-by: David Howells <dhowells@redhat.com>
Cc: Dave Airlie <airlied@linux.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Fix the SIS DRM memory allocator if the SIS FB built as a module. The SIS DRM
code initialises the mm allocation hooks, but _only_ if the SIS FB is not
built as a module because it depends on CONFIG_FB_SIS, and that's unset if the
SIS FB is not built in. It must check CONFIG_FB_SIS_MODULE as well.
Signed-off-by: David Howells <dhowells@redhat.com>
Cc: Dave Airlie <airlied@linux.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If this triggers its bad, however some machines seem to have been
triggering it for ages and we didn't know until we added the debug.
So downgrade the debug now so people don't call this a regression.
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'drm-patches' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm: don't set the signal blocker on the master process.
drm: don't call the vblank tasklet with irqs disabled.
r300: Fix cliprect emit
drm/radeon: r300_cmdbuf: Always emit INDX_BUFFER immediately after DRAW_INDEX
radeon: fix some hard lockups on r3/4/500s
There is a problem with debugging the X server and gdb crashes in
the xkb startup code.
This avoids the problem by allowing the master process to get signals.
It should be safe as the signal blocker is mainly so that you can
Ctrl-Z a 3D application without locking up the whole box. Ctrl-Z the
X server isn't something many people do.
Signed-off-by: Dave Airlie <airlied@redhat.com>
If a specific tasklet shares data with irq context,
it needs to take a private irq-blocking spinlock within
the tasklet itself.
Signed-off-by: Dave Airlie <airlied@redhat.com>
This makes our handling of cliprects sane. drm_clip_rect always has exclusiv
bottom-right corners, but the hardware expects inclusive bottom-right corner
so we adjust this here.
This complements Michel Daenzer's commit 57aea290e1e0a26d1e74df6cff777eb9f03
to Mesa. See also http://bugs.freedesktop.org/show_bug.cgi?id=16123
Signed-off-by: Dave Airlie <airlied@redhat.com>
DRAW_INDEX writes a vertex count to VAP_VF_CNTL. Docs say that behaviour
is undefined (i.e. lockups happen) when this write is not followed by the
right number of vertex indices.
Thus we used to do the wrong thing when drawing across many cliprects was
necessary, because we emitted a sequence
DRAW_INDEX, DRAW_INDEX, INDX_BUFFER, INDX_BUFFER
instead of
DRAW_INDEX, INDX_BUFFER, DRAW_INDEX, INDX_BUFFER
The latter is what we're doing now and which ought to be correct.
Signed-off-by: Dave Airlie <airlied@redhat.com>
This patch should fix hard lockup and convert them in
softlockup (ie you can ssh the box but the gpu is busted
and we are waiting in loop for it to come back to reason).
Signed-off-by: Dave Airlie <airlied@redhat.com>
Some module parameters with only one line have the '\n' at the end of the
description. This is not needed nor wanted as after the description the
type (i.e. int) is followed by a newline.
Some modules contain a multi-line description, these are not affected
by this patch.
Signed-off-by: Niels de Vos <niels.devos@wincor-nixdorf.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: Ed L. Cashin <ecashin@coraid.com>
Cc: Dave Airlie <airlied@linux.ie>
Cc: Roland Dreier <rolandd@cisco.com>
Acked-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make the needlessly global drm_minors_cleanup() static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With new userspace libpciaccess we can get a conflicting mapping
on the PCIE GART table in the video RAM. Always try and map it _wc.
Signed-off-by: Dave Airlie <airlied@redhat.com>
With the coming of kernel based modesetting and the memory manager stuff,
the everything in one directory approach was getting very ugly and
starting to be unmanageable.
This restructures the drm along the lines of other kernel components.
It creates a drivers/gpu/drm directory and moves the hw drivers into
subdirectores. It moves the includes into an include/drm, and
sets up the unifdef for the userspace headers we should be exporting.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Kristian Høgsberg