This patch adds the quirks and compatible string in sdhci-of-arasan.c
to support sdhci-arasan4.9a version of controller.
Signed-off-by: Suman Tripathi <stripathi@apm.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The platform_device_id is not modified by the driver and core uses it as
const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The platform_device_id is not modified by the driver and core uses it as
const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The platform_device_id is not modified by the driver and core uses it as
const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The platform_device_id is not modified by the driver and core uses it as
const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The platform_device_id is not modified by the driver and core uses it as
const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The platform_device_id is not modified by the driver and core uses it as
const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
chips have some issues for version and capbility registers, here we fake
them.
Signed-off-by: Weijun Yang <Weijun.Yang@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
hardware has 16bit to record the tuning count, so fix it to 16384.
at the same time, tuned_phases[SIRF_TUNING_COUNT] is useless as the
array is never used, so move it to a variant.
Signed-off-by: Weijun Yang <Weijun.Yang@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Clean up resource allocation and freeing.
Signed-off-by: Ian Molton <ian.molton@codethink.co.uk>
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
sdhci_alloc_host() takes priv_size rather than
sizeof(struct sdhci_host) + priv_size.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For PowerPC esdhc pre divider starts at 1, fixing the increases
the actual clock from 40KHz to 50 KHz.
Signed-off-by: Joakim Tjernlund <joakim.tjernlund@transmode.se>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
My Pengutronix address is not valid anymore, redirect people to the Pengutronix
kernel team.
Reported-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Robert Schwebel <r.schwebel@pengutronix.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Current sh_mmcif_clk_update() is called from probe() and set_ios(),
but, the purpose of later one is just clk_prepare_enable().
No need to setup mmc->f_max/f_min in many times.
This patch separe sh_mmcif_clk_update() into clk_prepare_enable()
and mmc->f_max/f_min setup.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Keita Kobayashi <keita.kobayashi.ym@renesas.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
struct sh_mmcif_host has 1) int clk, 2) struct clock *hclk,
and host->clk = clk_get_rate(host->hclk).
This int clk is not necessary. Let's remove it.
And, current hclk is confusable naming. Let's rename it to clk.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Keita Kobayashi <keita.kobayashi.ym@renesas.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We can now use generic wakeirq handling and remove the custom handling
for the wake-up interrupts.
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
clkdiv is declared as an u32 but it can be set to a negative value
causing a huge divisor value. Change its type to int to avoid this case.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Cc: <stable@vger.kernel.org> # 3.4 and later
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When non-removable is used for emmc, MMC_CAP_NONREMOVABLE should
also be checked, otherwise detection fail since present=0
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Set 0 to des1 in 32bit case.
Otherwise the random value of des1 will be used in
dw_mci_translate_sglist: IDMAC_SET_BUFFER1_SIZE(desc, length)
Signed-off-by: Fei Wang <w.f@huawei.com>
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
f9fd54f22e ("mmc: sh_mmcif: Use msecs_to_jiffies() for host->timeout")
changed the timeout value from 1000 jiffies to 1s. In the case where
HZ is 1000 the values are the same. However, for smaller HZ values the
timeout is now smaller, 1s instead of 10s in the case of HZ=100.
Since the timeout occurs in spite of a normal data transfer a timeout of
10s seems more appropriate. This restores the previous timeout in the
case where HZ=100 and results in an increase over the previous timeout
for larger values of HZ.
Fixes: f9fd54f22e ("mmc: sh_mmcif: Use msecs_to_jiffies() for host->timeout")
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[horms: rewrote changelog to refer to HZ]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We don't have any arch specific scatterlist now that parisc switched over
to the generic one.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
We've got a fairly large cleanup branch this time. The bulk of this is removal
of non-DT platforms of several flavors:
- Atmel at91 platforms go full-DT, with removal of remaining board-file based
support
- OMAP removes legacy board files for three more platforms
- Removal of non-DT mach-msm, newer Qualcomm platforms now live in mach-qcom
- Freescale i.MX25 also removes non-DT platform support
Most of the rest of the changes here are fallout from the above, i.e. for
example removal of drivers that now lack platforms, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=BV8A
-----END PGP SIGNATURE-----
Merge tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"We've got a fairly large cleanup branch this time. The bulk of this
is removal of non-DT platforms of several flavors:
- Atmel at91 platforms go full-DT, with removal of remaining
board-file based support
- OMAP removes legacy board files for three more platforms
- removal of non-DT mach-msm, newer Qualcomm platforms now live in
mach-qcom
- Freescale i.MX25 also removes non-DT platform support"
Most of the rest of the changes here are fallout from the above, i.e. for
example removal of drivers that now lack platforms, etc.
* tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (58 commits)
mmc: Remove msm_sdcc driver
gpio: Remove gpio-msm-v1 driver
ARM: Remove mach-msm and associated ARM architecture code
ARM: shmobile: cpuidle: Remove the pointless default driver
ARM: davinci: dm646x: Add interrupt resource for McASPs
ARM: davinci: irqs: Correct McASP1 TX interrupt definition for DM646x
ARM: davinci: dm646x: Clean up the McASP DMA resources
ARM: davinci: devices-da8xx: Add support for McASP2 on da830
ARM: davinci: devices-da8xx: Clean up and correct the McASP device creation
ARM: davinci: devices-da8xx: Add interrupt resource to McASP structs
ARM: davinci: devices-da8xx: Add resource name for the McASP DMA request
ARM: OMAP2+: Remove legacy support for omap3 TouchBook
ARM: OMAP3: Remove legacy support for devkit8000
ARM: OMAP3: Remove legacy support for EMA-Tech Stalker board
ARM: shmobile: Consolidate the pm code for R-Car Gen2
ARM: shmobile: r8a7791: Correct SYSCIER value
ARM: shmobile: r8a7790: Correct SYSCIER value
ARM: at91: remove old setup
ARM: at91: sama5d4: remove useless map_io
ARM: at91: sama5 use SoC detection infrastructure
...
- Numerous minor fixes, cleanups etc.
- More EEH work from Gavin to remove its dependency on device_nodes.
- Memory hotplug implemented entirely in the kernel from Nathan Fontenot.
- Removal of redundant CONFIG_PPC_OF by Kevin Hao.
- Rewrite of VPHN parsing logic & tests from Greg Kurz.
- A fix from Nish Aravamudan to reduce memory usage by clamping
nodes_possible_map.
- Support for pstore on powernv from Hari Bathini.
- Removal of old powerpc specific byte swap routines by David Gibson.
- Fix from Vasant Hegde to prevent the flash driver telling you it was flashing
your firmware when it wasn't.
- Patch from Ben Herrenschmidt to add an OPAL heartbeat driver.
- Fix for an oops causing get/put_cpu_var() imbalance in perf by Jan Stancek.
- Some fixes for migration from Tyrel Datwyler.
- A new syscall to switch the cpu endian by Michael Ellerman.
- Large series from Wei Yang to implement SRIOV, reviewed and acked by Bjorn.
- A fix for the OPAL sensor driver from Cédric Le Goater.
- Fixes to get STRICT_MM_TYPECHECKS building again by Michael Ellerman.
- Large series from Daniel Axtens to make our PCI hooks per PHB rather than per
machine.
- Small patch from Sam Bobroff to explicitly abort non-suspended transactions
on syscalls, plus a test to exercise it.
- Numerous reworks and fixes for the 24x7 PMU from Sukadev Bhattiprolu.
- Small patch to enable the hard lockup detector from Anton Blanchard.
- Fix from Dave Olson for missing L2 cache information on some CPUs.
- Some fixes from Michael Ellerman to get Cell machines booting again.
- Freescale updates from Scott: Highlights include BMan device tree nodes, an
MSI erratum workaround, a couple minor performance improvements, config
updates, and misc fixes/cleanup.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=03Yh
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux
Pull powerpc updates from Michael Ellerman:
- Numerous minor fixes, cleanups etc.
- More EEH work from Gavin to remove its dependency on device_nodes.
- Memory hotplug implemented entirely in the kernel from Nathan
Fontenot.
- Removal of redundant CONFIG_PPC_OF by Kevin Hao.
- Rewrite of VPHN parsing logic & tests from Greg Kurz.
- A fix from Nish Aravamudan to reduce memory usage by clamping
nodes_possible_map.
- Support for pstore on powernv from Hari Bathini.
- Removal of old powerpc specific byte swap routines by David Gibson.
- Fix from Vasant Hegde to prevent the flash driver telling you it was
flashing your firmware when it wasn't.
- Patch from Ben Herrenschmidt to add an OPAL heartbeat driver.
- Fix for an oops causing get/put_cpu_var() imbalance in perf by Jan
Stancek.
- Some fixes for migration from Tyrel Datwyler.
- A new syscall to switch the cpu endian by Michael Ellerman.
- Large series from Wei Yang to implement SRIOV, reviewed and acked by
Bjorn.
- A fix for the OPAL sensor driver from Cédric Le Goater.
- Fixes to get STRICT_MM_TYPECHECKS building again by Michael Ellerman.
- Large series from Daniel Axtens to make our PCI hooks per PHB rather
than per machine.
- Small patch from Sam Bobroff to explicitly abort non-suspended
transactions on syscalls, plus a test to exercise it.
- Numerous reworks and fixes for the 24x7 PMU from Sukadev Bhattiprolu.
- Small patch to enable the hard lockup detector from Anton Blanchard.
- Fix from Dave Olson for missing L2 cache information on some CPUs.
- Some fixes from Michael Ellerman to get Cell machines booting again.
- Freescale updates from Scott: Highlights include BMan device tree
nodes, an MSI erratum workaround, a couple minor performance
improvements, config updates, and misc fixes/cleanup.
* tag 'powerpc-4.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux: (196 commits)
powerpc/powermac: Fix build error seen with powermac smp builds
powerpc/pseries: Fix compile of memory hotplug without CONFIG_MEMORY_HOTREMOVE
powerpc: Remove PPC32 code from pseries specific find_and_init_phbs()
powerpc/cell: Fix iommu breakage caused by controller_ops change
powerpc/eeh: Fix crash in eeh_add_device_early() on Cell
powerpc/perf: Cap 64bit userspace backtraces to PERF_MAX_STACK_DEPTH
powerpc/perf/hv-24x7: Fail 24x7 initcall if create_events_from_catalog() fails
powerpc/pseries: Correct memory hotplug locking
powerpc: Fix missing L2 cache size in /sys/devices/system/cpu
powerpc: Add ppc64 hard lockup detector support
oprofile: Disable oprofile NMI timer on ppc64
powerpc/perf/hv-24x7: Add missing put_cpu_var()
powerpc/perf/hv-24x7: Break up single_24x7_request
powerpc/perf/hv-24x7: Define update_event_count()
powerpc/perf/hv-24x7: Whitespace cleanup
powerpc/perf/hv-24x7: Define add_event_to_24x7_request()
powerpc/perf/hv-24x7: Rename hv_24x7_event_update
powerpc/perf/hv-24x7: Move debug prints to separate function
powerpc/perf/hv-24x7: Drop event_24x7_request()
powerpc/perf/hv-24x7: Use pr_devel() to log message
...
Conflicts:
tools/testing/selftests/powerpc/Makefile
tools/testing/selftests/powerpc/tm/Makefile
Some additional quirks need to be enabled now we support UHS
modes. This avoids some spurious warnings like
"Got data interrupt 0x00000002 even though no data operation was in progress"
Testing on stih410-b2120 board achieves the following speeds
with HS200 eMMC card.
max-frequency = 200Mhz
/dev/mmcblk0p1:
Timing buffered disk reads: 270 MB in 3.02 seconds = 89.54 MB/sec
max-frequency = 100Mhz
root@debian-armhf:~# hdparm -t /dev/mmcblk0p1
/dev/mmcblk0p1:
Timing buffered disk reads: 210 MB in 3.00 seconds = 70.00 MB/sec
max-frequency = 50Mhz
root@debian-armhf:~# hdparm -t /dev/mmcblk0p1
/dev/mmcblk0p1:
Timing buffered disk reads: 118 MB in 3.00 seconds = 39.28 MB/sec
This is better than the 3.10 kernel which achieves 77.59 MB/sec
at 200Mhz clock (same board/soc/eMMC).
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To allow UHS modes to work properly we need to provide the st specific
set_uhs_signaling callback function. This function differs from the
generic sdhci_set_uhs_signaling callback in that we need to configure
the correct delay depending on the UHS mode, and also set the V18_EN
bit.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
STiH407 family SoC's have glue registers in the flashSS subsystem which
are used to configure the Arasan HC. This patch configures these glue
registers according to what has been specified in the DT.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Due to the tight timing constraints in some UHS modes, it is required to have
some delay management in the design. Two types of delay management are supported
in the HW: -
1) Static delay management
2) Dynamic delay management
NB: The delay management is only there when eMMC interface is selected.
1: Static delay management: is used to provide PVT dependent static delay on the
clock/data lines to manage setup/hold requirements of the interface. The maximum
delay possible is 3.25ns. These delays are PVT dependent, and thus delay values
applied are not accurate and vary across provcess voltage and temperature range.
Due to this these delays must not be used on the very time critical paths.
2. Dynamic delay locked loop (DLL): is used to provide dynamic delay management.
The advantage of DLL is that it provides accurate & PVT indepedent delay.
The DLL is used to provide delay on the loopback clock on "Read Path" to capture
read data reliably. On TX path the clock on which output data is transmitted is
delayed, resulting in delay of TX data.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
STiH407 family SoC's can have a reset signal for the controller which needs to
be managed. Also the eMMC controller has some additional 'top' memory mapped
registers which are used to manage the dynamic and static delay required for
UHS modes. This patch adds support for creating the mapping, which will be used
by subsequent patches.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The stih407 family SoC's have additional glue registers in the flashSS which
are used to configure the Arasan controller.
This patch adds macros for the register offsets and bitfields which will be
used by subsequent patches to support stih407 family SoC's.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently it is not possible to use 'mmc-pwrseq-simple' property with this
driver because mmc_of_parse() is never called.
mmc_of_parse() calls mmc_pwrseq_alloc() that manages MMC power sequence and
allows passing GPIOs in the devicetree to properly power/reset the Wifi
chipset.
When using mmc_of_parse() we no longer need to have custom code to request
card-detect and write-protect pins, as this can now be handled by the mmc
core.
Tested on a imx6sl-warp board where BT/Wifi is functional and also on a
imx6q-sabresd.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It is possible for the cmd11 interrupt to fire and delete the
cmd11_timer before the cmd11_timer was actually setup. Let's fix this
race by adding a few spinlocks. Note that the race wasn't seen in
practice without adding some printk statements, but it still seems
wise to fix.
Fixes: 5c935165da ("mmc: dw_mmc: Add a timeout for sending CMD11")
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If we get an unexpected cmd11 timeout we shouldn't actually treat it
as a timeout (not that we really expect to get an unexpected cmd11
timeout, but still).
Fixes: 5c935165da ("mmc: dw_mmc: Add a timeout for sending CMD11")
Reported-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Although the cmd11 interrupt should come within 2ms, that's a very
short time. Let's increase the timeout to be really sure that we
don't get an accidnetal timeout. One case in particular this is
useful is if you've got a serial console and printk in just the right
places. Under that scenario I've seen delays of up to 130ms before
the interrupt fired.
CMD11 is only sent during card insertion, so this extra timeout
shouldn't be terrible.
Fixes: 5c935165da ("mmc: dw_mmc: Add a timeout for sending CMD11")
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The dw_mmc driver changes to make the IO accesors endian agnostic did not
take into account the fifo accesses do not need to be swapped. To fix this
add a mmci_fifo_read/write wrapper to allow these to be passed through the
IO without being swapped.
Since these are now specific functions, it would be easier just to store
the pointer to the fifo registers in the host block instead of the offset
to them. So change the host->data_offset to host->fifo_reg (which also
means we catch all the places this is read or written).
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The dw_mmc driver does not take into account the processor may be in
big endian when writing the descriptors. Change the descriptors for
the 32bit IDMA to use __le32 and ensure they are suitably swapped
before writing.
Note, this has not been tested as the socfpga driver does not try to
use idma.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The dw_mmc driver does not use endian agnostic IO accessors, so fix
the use of __raw reads and writes to be the relaxed versions.
This fixes the dw_mmc driver initialisation on Altera socfpga in big endian.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Also check MMC OF properties. The controller supports MMC too.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
strip the card dectet logic from cover detect isr and vice versa
the generic mmc_gpio_cd_irqt isr, uses 200ms on removal/insertion,
hence that should be fine here as well
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If dw_mci_init_slot() returns that we got a probe deferral then it may
leave slot->mmc as NULL. That will cause dw_mci_enable_cd() to crash
when it calls mmc_gpio_get_cd().
Fix this by moving the call of dw_mci_enable_cd() until we're sure
that we're good. Note that if we have more than one slot and one
defers (but the others don't) things won't work so well. ...but
that's not a new thing and everyone has already agreed that multislot
support ought to be removed from dw_mmc eventually anyway since it is
unused, untested, and you can see several bugs like this by inspecting
the code.
Fixes: bcafaf5470f0 ("mmc: dw_mmc: Only enable CD after setup and only if needed")
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In the Designware databook's description of the "Voltage Switch Normal
Scenario" it instructs us to set a timer and fail the voltage change
if we don't see the voltage change interrupt within 2ms. Let's
implement that. Without implementing this I have often been able to
reproduce a hang while trying to send CMD11 on an rk3288-based board
while constantly ejecting and inserting UHS cards.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This driver is orphaned now that mach-msm has been removed.
Delete it.
Cc: Chris Ball <chris@printf.net>
Cc: David Brown <davidb@codeaurora.org>
Cc: Bryan Huntsman <bryanh@codeaurora.org>
Cc: Daniel Walker <dwalker@fifo99.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
board-rx51 has no card detect pin in the mmc slot, but can detect that
the (cell-phone) cover has been removed and the card is accessible.
The semantics between cover/card detect differ, the gpio on the slot
informs you after the card has been removed, cover removal does not
necessarily mean that the card has been removed.
This means different code paths are necessary. To complete this we
also want different fields in the platform data for cover and card
detect. This separation is not pushed all the way down into struct
omap2_hsmmc_info which is used to initialize the platform data.
If we did that we had to go over all board files and set the new
gpio_cod pin to -EINVAL. If we forget one board or some out-of-tree
archicture forgets that the default '0' is used which is a valid pin
number.
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The ->enable|disable() callbacks are only used to get and put runtime
PM references. Currently omap_hsmmc's ->set_ios() already does this
itself.
Other host drivers deals with runtime PM without using the
->enable|disable() callbacks and thus do the runtime PM reference
counting themselves. Apply that approach for omap_hsmmc as well and
then discard the ->enable|disable() callbacks.
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some versions of this controller do not advertise their 3.0v and
8bit bus-width support capabilities. It is required to explicitly
set these capabilities for the specific controller versions.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Change the __raw IO functions to endian agnostic relaxed ones to allow
the driver to function on big endian ARM systems.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When the MXC MMUC driver is used on a Freescale MPC512x machine, it
contains some additional byteswapping code (I'm assuming this is a
workaround for a hardware defect). This uses the ppc specific st_le32()
function, but there's no reason not to use the generic swab32() function
instead. gcc is capable of generating the efficient ppc byte-reversing
load/store instructions without the arch-specific helper.
This patch, therefore, switches to the generic byteswap routine.
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When the sunxi mmc-controller code was initially merged MMC_CAP_SDIO_IRQ was
not added to the host caps because of issues with some sdio wifi modules.
It turns out that these issues have nothing to do with using sdio-irq support,
they also happen with oob interrupts. Since the hardware supports sdio-irq
everywhere, and since the one reason to not claim the capability is gone,
add MMC_CAP_SDIO_IRQ to the default host caps.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The driver co-allocates sdhci_iproc_host with sdhci_pltfm_host and so to
access it we need to use sdhci_pltfm_priv() and not pltfm_host->priv.
Signed-off-by: Dmitry Torokhov <dtor@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The sdhci_request function should consider a non-removable device
always present.
Call the correct logic already available in sdhci_do_get_cd function.
This fixes some logic paths where MMC requests are being made to
non-removable devices that do not have the card detect pin connected
on the hardware as it is non-removable.
Signed-off-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Move the member for card_int_gpio into the struct spear_sdhci.
In this way we eliminate the last user of the struct sdhci_plat_data,
which enables us to remove the exported header for sdhci-spear.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This driver is used on SoCs which are using CONFIG_OF. By adding a
compile dependency in the Kconfig, it enables us to simplify some code.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Since there no users of the struct sdhci_host, but the shdci host
drivers themselves, let's move the definition of it to the local sdhci
header.
The exported sdhci header then becomes empty, so let's remove it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Since commit cd1e65044d ("of/device: Don't register disabled
devices"), the disabled device will not be registered at all. So
we don't need to do the check again in the platform device driver.
And the check in the current code is useless even if we really
run into a disabled device. In this case, it just doesn't parse
the dtb for the infos such as quirks or clock, but it will continue
to try to init the disabled device after that check. So just remove it.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Setup a different set of sdhci_ops for tegra114 and later so that
the write_w callback is only used on tegra114. This allows us to
remove the NVQUIRK_SHADOW_XFER_MODE_REG and simply the logic
in tegra_sdhci_writew.
Suggested-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
A command end interrupt should not be processed between command issue
and setting of wait_for flag. It expects already the flag to be set.
Therefore the exclusive control was added.
Signed-off-by: Kouichi Tomita <kouichi.tomita.yn@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If interruption of command already occurred, mrq pointer in dev_err()
would refer to NULL, because the host-state is changed to STATE_IDLE
and mrq pointer is changed to NULL by interrupt handler.
Therefore dev_err is moved after checking STATE_IDLE.
Signed-off-by: Kouichi Tomita <kouichi.tomita.yn@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It was brought to my attention that the sdhci-pxav3 driver is needed
on a few more ARM machines than I initially thought. Add the missing
architectures to the dependency list.
Credits to Peter Robinson for noticing my mistake and reporting.
Reported-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Chris Ball <chris@printf.net>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The sunxi mmc driver tries to calculate a dma address by using pointer
arithmetic, which causes a warning when dma_addr_t is wider than a pointer:
drivers/mmc/host/sunxi-mmc.c: In function 'sunxi_mmc_init_idma_des':
drivers/mmc/host/sunxi-mmc.c:296:35: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
struct sunxi_idma_des *pdes_pa = (struct sunxi_idma_des *)host->sg_dma;
^
To avoid this warning and to simplify the logic, this changes
the code to avoid the cast and calculate the correct address
manually. The behavior should be unchanged.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: David Lanzendörfer <david.lanzendoerfer@o2s.ch>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The PPC_OF is a ppc specific option which is used to mean that the
firmware device tree access functions are available. Since all the
ppc platforms have a device tree, it is aways set to 'y' for ppc.
So it makes no sense to keep a such option in the current kernel.
Replace it with PPC.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For CMD53 in block mode, the host does not need to stop the transfer,
as it stops when the block count (present in CMD53) is reached.
Signed-off-by: Corneliu Doban <cdoban@broadcom.com>
Signed-off-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add quirk to handle broken auto-CMD23.
Some controllers do not respond after the first auto-CMD23 is issued.
This allows CMD23 to still work (mandatory for the faster UHS-I mode)
rather than disabling CMD23 entirely via SDHCI_QUIRK2_HOST_NO_CMD23.
Signed-off by: Corneliu Doban <cdoban@broadcom.com>
Signed-off-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Static checkers suggest that probably we intended to put curly braces
around the writel() to make it part of the else path. But, I think
actually the indenting is off and the code works fine as is.
The stray tab was introduced in 0322191e62 ('mmc: sdhci-esdhc-imx: add
sd3.0 SDR clock tuning support')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Dong Aisheng <b29396@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Setting a dev_pm_ops suspend/resume pair but not a set of
hibernation functions means those pm functions will not be
called upon hibernation.
Fix this by using SET_SYSTEM_SLEEP_PM_OPS, which appropriately
assigns the suspend and hibernation handlers and move
omap_hsmmc_x callbacks under CONFIG_PM_SLEEP to avoid build warnings.
Signed-off-by: Russ Dill <Russ.Dill@ti.com>
[Grygorii.Strashko@linaro.org: rebased on top of K4.0]
Signed-off-by: Grygorii Strashko <grygorii.strashko@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Mobile phones (some) have no card detect pin, but can detect if the
cover is removed. The purpose is the same; detect if card is being
added/removed, but the details differ.
When the cover is removed, it does not mean the card is gone. But it
might, since it is accessible now. It's like a warning. All the driver
does is to limit write access to the card, see protect_card flag.
In contrast, card detect notifies us after the fact, e.g.
card is gone, card is inserted. We can't take precautions, but we can
rely on those events, -- the card is really gone, or do scan the card.
To summarize there is not much code sharing between cover and card
detect, it only increases confusion. By splitting, both will be
simplified in a followup patch.
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The indirection via omap_hsmmc_get_ro and omap_hsmmc_get_wp is
redundant. Also dropped setting gpio_wp to EINVAL since platform date
is read-only
Untested: no device with ro pin was available, but change is fairly
simple
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
addon to: 09108968b7b72b6083a3bfc8f8259a74ed57255e
mmc: omap_hsmmc: remove prepare/complete system suspend support
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The reset control for the sunxi mmc controller is optional. Some
newer platforms (sun6i, sun8i, sun9i) have it, while older ones
(sun4i, sun5i, sun7i) don't.
Use the properly stubbed _optional version so the driver does not
fail to compile when RESET_CONTROLLER=n.
This patch also adds a check for deferred probing on the reset
control.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Cc: <stable@vger.kernel.org> # 3.16+
Acked-by: David Lanzendörfer <david.lanzendoerfer@o2s.ch>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In these drivers, the driver specific .remove function just a simple
wrapper of function sdhci_pltfm_unregister(). So remove these wrappers
and just set .remove to sdhci_pltfm_unregister().
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
So we can avoid to sprinkle the clk_disable_unprepare() in many
drivers.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Actually we can use the "clk" in the struct sdhci_pltfm_host. Also
change the "external clock" to "core clock" and kill two redundant
private functions in this driver as suggested by Ray Jui.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Actually we can use the "clk" in the struct sdhci_pltfm_host.
With this change we can also kill the private function for get
max clock in this driver.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There is only one "clk" member in this driver specific private struct.
Actually we can use the "clk" member in the struct sdhci_pltfm_host,
and then kill this struct completely.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The function clk_disable_unprepare() already take care of either error
or null cases.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For the original tuning code, delay value is set to SD Bus Clock Delay
Register (SD_CLK_DELAY_SETTING) as (val | (Val << 7) | (val << 16)),
which means CLK_DELAY_IN1, CLK_DELAY_IN2 and CLK_DELAY_OUT are the
same and with 128 steps. This is doubtful. In CSR design specification
documents CS-304575-DR-3H, this issue is clarified, the delay[13:0] in
SD_CLK_DELAY_SETTING is simplied to the concatenation of {CLK_DELAY_IN2,
CLK_DELAY_IN1}.
Besides, for CMD19 tuning, no need to set CLK_DELAY_OUT([22,16]
of SD_CLK_DELAY_SETTING).
Signed-off-by: weijun yang <york.yang@csr.com>
Signed-off-by: Barry Song <baohua.song@csr.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It's unlikely that this is really needed on any single-slot systems
where we disable card detects until the end of probe, but it still
seems safer to check to make sure that a slot has been initted before
we try to dereference it to find the SDIO interrupt mask.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We really don't want to get a card detect interrupt during probe time
since it can confuse things. Let's disable the card detect interrupt
until we're in a really good place: the end of probe. Let's also
simply avoid enabling the card detect interrupt if it's not used.
It appears that (at least on rk3288) when vqmmc is turned on it can
cause a bogus "card detect" interrupt. That meant that we were
getting a predictable card detect interrupt while we were in
mmc_add_host(). On the version of the kernel I'm working with at
least (3.14), this is not a great time to get a card detect interrupt
since I think that we don't grab all the needed locks in
mmc_add_host() and children. I put stack dumps in dw_mci_setup_bus()
and found that I could see two distinct stack crawls that looked like:
Caller one:
* dw_mci_setup_bus
* dw_mci_set_ios
* mmc_power_up
* mmc_start_host
* mmc_add_host
Caller two:
* dw_mci_setup_bus
* dw_mci_set_ios
* mmc_set_chip_select
* mmc_go_idle
* mmc_rescan
* process_one_work
* worker_thread
* kthread
Signed-off-by: Doug Anderson <dianders@chromium.org>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We've seen problems on some WiFi modules where we seem to send a CMD53
(which requires the data lines) while the module is asserting busy.
We shouldn't do that.
The Designware Databook says that before issuing a new data transfer
command we should check for busy, so that's what we'll do.
We'll leverage the existing dw_mmc knowledge about whether it should
wait for the previous command to finish to know whether we should
check for busy before sending the command. This means we won't end up
incorrectly waiting for things like CMD52 (SDIO) or CMD13 (SD) which
don't use the data line.
Note that this also has the advantage of making sure that we don't
change the clock while the card is busy, too.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We should give dw_mmc a good reset after we apply power. On some
boards vqmmc may actually be connected to the IP block in the SoC so
it's good to reset after power comes in.
Without this we sometimes see failures enumerating cards on rk3288.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It appears that we can confuse things if we try to turn on the MMC
clock when the power is off. Adjust is so that we turn the clock on
(using dw_mci_setup_bus) after power is all the way on and we turn the
clock off before the power goes off.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The STOP command can terminate a data transfer between a memory card and
mmc controller.
As show in Synopsys DesignWare Cores Mobile Storage Host Databook:
Data timeout and Data end-bit error will terminate further data transfer
by mmc controller. So we should not send abort command to terminate a
data transfer again if we got DRTO and EBE interrupt.
After this patch, all mmc_test cases can pass on RK3288-Pink2 board.
Signed-off-by: Addy Ke <addy.ke@rock-chips.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Tested-by: Doug Anderson <dianders@chromium.org>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To support HS200 and UHS mode, mmc core will call init_card() to
execute tuning:
- sdio: init_card can be executed at runtime resume.
- sd and mmc: init_card can be executed at resume or runtime resume,
which depends on MMC_CAP_RUNTIME_RESUME capability.
On rk3288 SoC, host will get DRTO interrupt when host send command
to read tuning data. This will spend more than 111ms:
drto_ms = drto_clks * 1000 / bus_hz = 111ms.
And the total tuning time will be more than 400ms.
So we should add MMC_CAP_RUNTIME_RESUME capability to execute tuning
at runtime resume. Only if we do so, can we pass resume test.
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Addy Ke <addy.ke@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Implements HS400 mode support for exynos host driver.
This also include some updates as new mode is added.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
[Alim: addressed review comments]
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Current sh_mobile_sdhi's platform data is set via sh_mobile_sdhi_info
and it is just copied to tmio_mmc_data.
Now, tmio mmc platform data is specified via tmio_mmc_data.
This patch replace sh_mobile_sdhi_info to tmio_mmc_data
struct sh_mobile_sdhi_info { -> struct tmio_mmc_data {
int dma_slave_tx; -> void *chan_priv_tx;
int dma_slave_rx; -> void *chan_priv_rx;
unsigned long tmio_flags; -> unsigned long flags;
unsigned long tmio_caps; -> unsigned long capabilities;
unsigned long tmio_caps2; -> unsigned long capabilities2;
u32 tmio_ocr_mask; -> u32 ocr_mask;
unsigned int cd_gpio; -> unsigned int cd_gpio;
}; unsigned int hclk;
void (*set_pwr)(...);
void (*set_clk_div)(...);
};
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
dma_request_slave_channel_compat() in tmio_mmc_dma
needs .chan_priv_tx/.chan_priv_rx. But these are copied from
sh_mobile_sdhi only, and sh_mobile_sdhi_info is now almost
same as tmio_mmc_data except .chan_priv_?x.
sh_mobile_sdhi_info can be replaced to tmio_mmc_data, but it is
used from ${LINUX}/arch/arm/mach-shmobile, ${LINUX}/arch/sh.
So, this patch adds .chan_priv_?x into tmio_mmc_data as 1st step,
and sh_mobile_sdhi driver has dummy operation for now.
It will be replaced/removed together with platform data replace.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Current tmio_mmc sets dma_slave_config :: slave_id field for DMAEngine,
but it is no longer needed. Let's remove it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Current sh_mmcif sets dma_slave_config :: slave_id field for DMAEngine,
but it is no longer needed. Let's remove it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
enhancements and fixes mostly for ARM32, ARM64, MIPS and Power-based
devices. Additionaly the framework core underwent a bit of surgery with
two major changes. The boundary between the clock core and clock
providers (e.g clock drivers) is now more well defined with dedicated
provider helper functions. struct clk no longer maps 1:1 with the
hardware clock but is a true per-user cookie which helps us tracker
users of hardware clocks and debug bad behavior. The second major change
is the addition of rate constraints for clocks. Rate ranges are now
supported which are analogous to the voltage ranges in the regulator
framework. Unfortunately these changes to the core created some
breakeage. We think we fixed it all up but for this reason there are
lots of last minute commits trying to undo the damage.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=zCVK
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus-3.20' of git://git.linaro.org/people/mike.turquette/linux
Pull clock framework updates from Mike Turquette:
"The clock framework changes contain the usual driver additions,
enhancements and fixes mostly for ARM32, ARM64, MIPS and Power-based
devices.
Additionally the framework core underwent a bit of surgery with two
major changes:
- The boundary between the clock core and clock providers (e.g clock
drivers) is now more well defined with dedicated provider helper
functions. struct clk no longer maps 1:1 with the hardware clock
but is a true per-user cookie which helps us tracker users of
hardware clocks and debug bad behavior.
- The addition of rate constraints for clocks. Rate ranges are now
supported which are analogous to the voltage ranges in the
regulator framework.
Unfortunately these changes to the core created some breakeage. We
think we fixed it all up but for this reason there are lots of last
minute commits trying to undo the damage"
* tag 'clk-for-linus-3.20' of git://git.linaro.org/people/mike.turquette/linux: (113 commits)
clk: Only recalculate the rate if needed
Revert "clk: mxs: Fix invalid 32-bit access to frac registers"
clk: qoriq: Add support for the platform PLL
powerpc/corenet: Enable CLK_QORIQ
clk: Replace explicit clk assignment with __clk_hw_set_clk
clk: Add __clk_hw_set_clk helper function
clk: Don't dereference parent clock if is NULL
MIPS: Alchemy: Remove bogus args from alchemy_clk_fgcs_detr
clkdev: Always allocate a struct clk and call __clk_get() w/ CCF
clk: shmobile: div6: Avoid division by zero in .round_rate()
clk: mxs: Fix invalid 32-bit access to frac registers
clk: omap: compile legacy omap3 clocks conditionally
clkdev: Export clk_register_clkdev
clk: Add rate constraints to clocks
clk: remove clk-private.h
pci: xgene: do not use clk-private.h
arm: omap2+ remove dead clock code
clk: Make clk API return per-user struct clk instances
clk: tegra: Define PLLD_DSI and remove dsia(b)_mux
clk: tegra: Add support for the Tegra132 CAR IP block
...
This change addresses following problem:
[ 2.560726] ------------[ cut here ]------------
[ 2.565341] WARNING: CPU: 0 PID: 1 at kernel/locking/lockdep.c:2744 lockdep_trace_alloc+0xec/0x118()
[ 2.574439] DEBUG_LOCKS_WARN_ON(irqs_disabled_flags(flags))
[ 2.579821] Modules linked in:
[ 2.583038] CPU: 0 PID: 1 Comm: swapper/0 Tainted: G W 3.18.0-next-20141216-00002-g4ff197fc1902-dirty #1318
[ 2.593796] Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
[ 2.599892] [<c0014c44>] (unwind_backtrace) from [<c0011bbc>] (show_stack+0x10/0x14)
[ 2.607612] [<c0011bbc>] (show_stack) from [<c04953b8>] (dump_stack+0x70/0xbc)
[ 2.614822] [<c04953b8>] (dump_stack) from [<c0023444>] (warn_slowpath_common+0x74/0xb0)
[ 2.622885] [<c0023444>] (warn_slowpath_common) from [<c0023514>] (warn_slowpath_fmt+0x30/0x40)
[ 2.631569] [<c0023514>] (warn_slowpath_fmt) from [<c0063644>] (lockdep_trace_alloc+0xec/0x118)
[ 2.640246] [<c0063644>] (lockdep_trace_alloc) from [<c00df52c>] (__kmalloc+0x3c/0x1cc)
[ 2.648240] [<c00df52c>] (__kmalloc) from [<c0394970>] (clk_fetch_parent_index+0xb8/0xd4)
[ 2.656390] [<c0394970>] (clk_fetch_parent_index) from [<c0394a6c>] (clk_calc_new_rates+0xe0/0x1fc)
[ 2.665415] [<c0394a6c>] (clk_calc_new_rates) from [<c0394b40>] (clk_calc_new_rates+0x1b4/0x1fc)
[ 2.674181] [<c0394b40>] (clk_calc_new_rates) from [<c0395408>] (clk_set_rate+0x50/0xc8)
[ 2.682265] [<c0395408>] (clk_set_rate) from [<c0377708>] (sdhci_cmu_set_clock+0x68/0x16c)
[ 2.690503] [<c0377708>] (sdhci_cmu_set_clock) from [<c03735cc>] (sdhci_do_set_ios+0xf0/0x64c)
[ 2.699095] [<c03735cc>] (sdhci_do_set_ios) from [<c0373b48>] (sdhci_set_ios+0x20/0x2c)
[ 2.707080] [<c0373b48>] (sdhci_set_ios) from [<c035ddf0>] (mmc_power_up+0x118/0x1fc)
[ 2.714889] [<c035ddf0>] (mmc_power_up) from [<c035ecd0>] (mmc_start_host+0x44/0x6c)
[ 2.722615] [<c035ecd0>] (mmc_start_host) from [<c035fd60>] (mmc_add_host+0x58/0x7c)
[ 2.730341] [<c035fd60>] (mmc_add_host) from [<c037454c>] (sdhci_add_host+0x968/0xd94)
[ 2.738240] [<c037454c>] (sdhci_add_host) from [<c0377b60>] (sdhci_s3c_probe+0x354/0x52c)
[ 2.746406] [<c0377b60>] (sdhci_s3c_probe) from [<c0283b58>] (platform_drv_probe+0x48/0xa4)
[ 2.754733] [<c0283b58>] (platform_drv_probe) from [<c02824e8>] (driver_probe_device+0x13c/0x37c)
[ 2.763585] [<c02824e8>] (driver_probe_device) from [<c02827bc>] (__driver_attach+0x94/0x98)
[ 2.772003] [<c02827bc>] (__driver_attach) from [<c0280a60>] (bus_for_each_dev+0x54/0x88)
[ 2.780163] [<c0280a60>] (bus_for_each_dev) from [<c0281b48>] (bus_add_driver+0xe4/0x200)
[ 2.788322] [<c0281b48>] (bus_add_driver) from [<c0282dfc>] (driver_register+0x78/0xf4)
[ 2.796308] [<c0282dfc>] (driver_register) from [<c00089b0>] (do_one_initcall+0xac/0x1f0)
[ 2.804473] [<c00089b0>] (do_one_initcall) from [<c0673d94>] (kernel_init_freeable+0x10c/0x1d8)
[ 2.813153] [<c0673d94>] (kernel_init_freeable) from [<c0490058>] (kernel_init+0x28/0x108)
[ 2.821398] [<c0490058>] (kernel_init) from [<c000f268>] (ret_from_fork+0x14/0x2c)
[ 2.828939] ---[ end trace 03cc00e539849d1f ]---
clk_set_rate() tries to take clk's prepare_lock mutex while being in atomic
context entered in sdhci_do_set_ios().
The solution is inspired by similar situation in sdhci_set_power() also called
from sdhci_do_set_ios():
spin_unlock_irq(&host->lock);
mmc_regulator_set_ocr(mmc, mmc->supply.vmmc, vdd);
spin_lock_irq(&host->lock);
Note that since sdhci_s3c_set_clock() sets SDHCI_CLOCK_CARD_EN, proposed change
first resets this bit. It is reset anyway (by setting SDHCI_CLOCK_INT_EN bit
only) after call to clk_set_rate() in order to wait for the clock to stabilize
and is set again as soon as the clock becomes stable.
Signed-off-by: Paul Osmialowski <p.osmialowsk@samsung.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Jonas Jensen wanted to submit a patch for these, but apparently
forgot about it. I stumbled over this symptom first:
drivers/built-in.o: In function `moxart_probe':
:(.text+0x2af128): undefined reference to `of_dma_request_slave_channel'
This is because of_dma_request_slave_channel is an internal helper
and not exported to loadable module. I'm changing the driver to
use dma_request_slave_channel_reason() instead.
Further problems from inspection:
* The remove function must not call kfree on the host pointer,
because it is allocated together with the mmc_host.
* The clock is never released
* The dma_cap_mask_t is completely unused and can be removed
* deferred probing does not work if the dma driver is loaded
after the mmc driver.
This patch should fix all of the above.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
I seem to understand that the sdhci-pxav3 and sdhci-pxav2 drivers are
only needed on the MMP architecture. So add a hardware dependency on
ARCH_MMP, so that other users don't get to build useless drivers.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Chris Ball <chris@printf.net>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Eric Miao <eric.y.miao@gmail.com>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
According to erratum 'FE-2946959' both SDR50 and DDR50 modes require
specific clock adjustments in SDIO3 Configuration register.
This commit add the support of this register and for SDR50 or DDR50
mode use it as suggested by the erratum:
- Set the SDIO3 Clock Inv field in SDIO3 Configuration register to not
inverted.
- Set the Sample FeedBack Clock field to 0x1
[gregory.clement@free-electrons.com: port from 3.10]
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
According to erratum 'ERR-7878951' Armada 38x SDHCI controller has
different capabilities than the ones shown in its registers:
- it doesn't support the voltage switching: it can work either with
3.3V or 1.8V supply
- it doesn't support the SDR104 mode
- SDR50 mode doesn't need tuning
The SDHCI_QUIRK_MISSING_CAPS quirk is used for updating the
capabilities accordingly.
[gregory.clement@free-electrons.com: port from 3.10]
Fixes: 5491ce3f79 ("mmc: sdhci-pxav3: add support for the Armada 38x SDHCI controller")
Cc: <stable@vger.kernel.org> # v3.15+
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
According to erratum 'FE-2946959' both SDR50 and DDR50 modes require
specific clock adjustments in SDIO3 Configuration register. However,
this register was not part of the device tree binding. Even if the
binding can (and will) be extended we still need handling the case
where this register was not available. In this case we use the
SDHCI_QUIRK_MISSING_CAPS quirk remove them from the capabilities.
This commit is based on the work done by Marcin Wojtas<mw@semihalf.com>
Fixes: 5491ce3f79 ("mmc: sdhci-pxav3: add support for the Armada 38x SDHCI controller")
Cc: <stable@vger.kernel.org> # v3.15+
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
I observed the Host Control2 register isn't correctly restored
after runtime resuming on BG2Q. For example, the register reads
as 0x800c before runtime suspend, but it's set as 0x8004 after runtime
resuming. This could results in a non working host.
The reason is the Host Control2 is incorrectly reset when switching
voltage. We fix this by following the same sequence during initialization.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If there is a gap between xfer mode and command register writes,
tegra SDMMC controller can sometimes issue a spurious command before
the CMD register is written. To avoid this, these two registers need
to be written together in a single write operation.
This is implemented as an NVQUIRK as it applies to T114, T124 and
T132.
Signed-off-by: Pavan Kunapuli <pkunapuli@nvidia.com>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Current code checks "clk_delay_cycles > 0" to know whether the optional
"mrvl,clk_delay_cycles" is set or not. But of_property_read_u32() doesn't
touch clk_delay_cycles if the property is not set. And type of
clk_delay_cycles is u32, so we may always set pdata->clk_delay_cycles as a
random value.
This patch fix this problem by check the return value of of_property_read_u32()
to know whether the optional clk-delay-cycles is set or not.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Cc: <stable@vger.kernel.org> # v3.6+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
dw_mci_pltfm_remove() is not (nor should it be) marked as __exit,
so we should not be using __exit_p() wrapper with it.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Tested-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
dw_mci_pltfm_remove() is not (nor should it be) marked as __exit,
so we should not be using __exit_p() wrapper with it.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Tested-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Let MMC_SDHCI_BIG_ENDIAN_32BIT_BYTE_SWAPPER depend on MMC_SDHCI. Not
only this is more correct, but this also avoids breaking the alignment
of all other MMC_SDHCI_* options in menuconfig.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Chris Ball <chris@printf.net>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Albert Herranz <albert_herranz@yahoo.es>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Config option MMC_RICOH_MMC's help text reads:
If unsure, say Y.
However the option defaults to N. Set the default to Y to match the
recommendation in the help text.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Chris Ball <chris@printf.net>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Philipl Langdale <philipl@overt.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
DMA configuration has been removed from function mmci_dma_setup but the
local mask variable was not removed. This remains unused hence remove
it from the function and operations on it
Signed-off-by: Pramod Gurav <pramod.gurav@smartplayin.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch is to fix a race condition that may cause an unhandled irq,
which results in big sdhci interrupt numbers and endless "mmc1: got irq
while runtime suspended" msgs before v3.15.
Consider following scenario:
CPU0 CPU1
sdhci_pxav3_runtime_suspend()
spin_lock_irqsave(&host->lock, flags);
sdhci_irq()
spining on the &host->lock
host->runtime_suspended = true;
spin_unlock_irqrestore(&host->lock, flags);
get the &host->lock
runtime_suspended is true now
return IRQ_NONE;
Fix this race by using the core sdhci.c supplied sdhci_runtime_suspend_host()
in runtime suspend hook which will disable card interrupts. We also use the
sdhci_runtime_resume_host() in the runtime resume hook accordingly.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Cc: <stable@vger.kernel.org> # v3.9+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit 63589e92c2 ("clk: Ignore error and NULL pointers passed to
clk_{unprepare, disable}()") allows NULL or error pointer to be passed
unconditionally.
This patch is to simplify probe error and remove code paths.
However, we reserve the core clock checks in runtime suspend/resume code
because we want a little smaller latency.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Check sg_count before sending long data xfer.
Because dma_map_sg() return int, and sg_count may be negative,
so using int instead of unsigned.
Signed-off-by: Micky Ching <micky_ching@realsil.com.cn>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Return error-code directly if no card exist, this can
make card remove faster.
Signed-off-by: Micky Ching <micky_ching@realsil.com.cn>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
drivers/mmc/host/sdhci_f_sdh30.c:143:5-11: inconsistent IS_ERR and PTR_ERR, PTR_ERR on line 144
PTR_ERR should access the value just tested by IS_ERR
Semantic patch information:
There can be false positives in the patch case, where it is the call
IS_ERR that is wrong.
Generated by: scripts/coccinelle/tests/odd_ptr_err.cocci
CC: Vincent Yang <vincent.yang.fujitsu@gmail.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
tmio_mmc_host has .enable_dma callback now.
We don't need TMIO_MMC_HAVE_CTL_DMA_REG anymore.
Let's remove it
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Now, sh_mobile_sdhi can use 32bit DMA access in R-Cer Gen2.
Let's use it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
getting struct sh_mobile_sdhi from struct mmc_host needs to use
complex container_of(). This patch adds new host_to_priv macro to
get it easily.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Latest SDHI on Renesas has expand register mapping.
update mmc_data->bus_shift for it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
No one is using .init/.cleanup callback function.
Let's remove these.
sdhi_ops and .cd_wakeup are also removed
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Renesas SDHI which is based on TMIO driver has 2 type SoC. 1st one is
used as SH-Mobile series, and 2nd is R-Car series. R-Car series SoC has
DMA buswidth setting register which enables 32bit access.
This patch adds .dma_buswidth and enables it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some controllers need DMA special register/setting.
This patch adds new .enable_dma callback for it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Current .dma_rx_offset is implemented under tmio_mmc_dma.
It goes to tmio_mmc_data by this patch.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Current .alignment_shift is implemented under tmio_mmc_dma.
It goes to tmio_mmc_data by this patch.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Current .bus_shift is implemented under tmio_mmc_data.
It goes to tmio_mmc_host by this patch.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Current .multi_io_quirk is implemented under tmio_mmc_data.
It goes to tmio_mmc_host by this patch.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Current .clk_disable is implemented under tmio_mmc_data.
It goes to tmio_mmc_host by this patch.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Current .clk_enable is implemented under tmio_mmc_data.
It goes to tmio_mmc_host by this patch.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Current .write16_hook is implemented under tmio_mmc_data.
It goes to tmio_mmc_host by this patch.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Current .dma is implemented under tmio_mmc_data.
It goes to tmio_mmc_host by this patch.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Current tmio_mmc driver is using tmio_mmc_data for driver/platform
specific data/callback, and it is needed for tmio_mmc_host_probe()
function. Because of this style, include/linux/mfd/tmio.h header has
tmio driver/framework specific data which is not needed from platform.
This patch adds new tmio_mmc_host_alloc/free() as cleanup preparation.
tmio driver specific data/callback will be implemented in tmio_mmc_host,
and platform specific data/callback will be implemented in tmio_mmc_data
in this cleanup.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds new host controller driver for
Fujitsu SDHCI controller f_sdh30.
Signed-off-by: Vincent Yang <Vincent.Yang@tw.fujitsu.com>
Signed-off-by: Andy Green <andy.green@linaro.org>
Signed-off-by: Tetsuya Takinishi <t.takinishi@jp.fujitsu.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch defines a quirk to disable the block count
for single block transactions.
It is a preparation and will be used by Fujitsu
SDHCI controller f_sdh30 driver.
Signed-off-by: Vincent Yang <Vincent.Yang@tw.fujitsu.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch defines a quirk for tuning work
around for some sdhci host controller. It sets
both SDHCI_CTRL_EXEC_TUNING and SDHCI_CTRL_TUNED_CLK
for tuning.
It is a preparation and will be used by Fujitsu
SDHCI controller f_sdh30 driver.
Signed-off-by: Vincent Yang <Vincent.Yang@tw.fujitsu.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds a callback function to do
controller-specific actions when switching voltages.
It is a preparation and will be used by Fujitsu
SDHCI controller f_sdh30 driver.
Signed-off-by: Vincent Yang <Vincent.Yang@tw.fujitsu.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If we power up vqmmc in MMC_POWER_ON then we end up turning it on
before mmc_power_up() sets the signal voltage. That's not so great
since we might be powering it up at the wrong voltage.
Note that this is how Yuvaraj originally coded things up in
<https://patchwork.kernel.org/patch/4401231/> but he changed it on my
suggestion. Apparently I was wrong.
Reported-by: Alexandru M Stan <amstan@chromium.org>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch solves the coding style issue by adding a space
before (
Signed-off-by: Mohammad Jamal <md.jamalmohiuddin@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch calls pm_runtime_put_noidle() to restore the device's usage
counter in the ->remove() implementation.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit 0dcaa2499b ("sdhci-pxav3: Fix runtime PM initialization") tries
to fix one hang issue caused by calling sdhci_add_host() on a suspended
device. The fix enables the clock twice, once by clk_prepare_enable() and
another by pm_runtime_get_sync(), meaning that the clock will never be
gated at runtime PM suspend. I observed the power consumption regression on
Marvell BG2Q SoCs.
In fact, the fix is not correct. There still be a very small window
during which a runtime suspend might somehow occur after pm_runtime_enable()
but before pm_runtime_get_sync().
This patch fixes all of the two problems by just incrementing the usage
counter before pm_runtime_enable(). It also adjust the order of disabling
runtime pm and storing the usage count in the error path to handle clock
gating properly.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Cc: <stable@vger.kernel.org> # v3.11+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There is no point making the initialization
of buf_ready_int conditional on host version.
Simplify by just doing it always. Note that
the other conditional initializations will be
removed when the new way of doing re-tuning
is taken into use.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This ensures that all standard options are available to hsmmc,
In particular, I need cap-power-off-card.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Using the common code removes some code duplication, and
makes it easier to switch to using mmc_of_parse() which
will remove more duplication.
This uses the new mmc_gpio_request_cd_isr to provide a non-standard
interrupt service routine for card-detect interrupts.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Just fix the comments, no functional changes.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch is based on the patches by Per Forlin, Tony Lin and Ryan QIAN.
This patch complete the API 'post_req' and 'pre_req' in sdhci host side,
Test Env:
1. i.MX6Q-SABREAUTO board, CPU @ 996MHz, use ADMA in uSDHC controller.
2. Test command:
$ echo 1 > /proc/sys/vm/drop_caches
write to sd card:
$ dd if=/dev/zero of=/dev/mmcblk0 bs=1M count=2000 conv=fsync
read the sd card:
$ dd if=/dev/mmcblk0 of=/dev/null bs=1M count=2000
3. TOSHIBA 16GB SD3.0 card, running at 4 bit, SDR104 @ 198MHZ
Performance with and without this patch:
-------------------------------------------------
| | read speed | write speed |
|------------------------------------------------
| with this patch | ~76.7 MB/s | ~23.3 MB/s |
|------------------------------------------------
|without this patch | ~60.5 MB/s | ~22.5 MB/s |
-------------------------------------------------
4. SanDisk 8GB SD3.0 card, running at 4 bit, DDR50 @ 50MHZ
Performance with and without this patch:
-------------------------------------------------
| | read speed | write speed |
|------------------------------------------------
| with this patch | ~40.5 MB/s | ~15.6 MB/s |
|------------------------------------------------
|without this patch | ~36.1 MB/s | ~14.1 MB/s |
-------------------------------------------------
5. Kingston 8GB SD2.0 card, running at 4 bit, High-speed @ 50MHZ
Performance with and without this patch:
-------------------------------------------------
| | read speed | write speed |
|------------------------------------------------
| with this patch | ~22.7 MB/s | ~8.2 MB/s |
|------------------------------------------------
|without this patch | ~21.3 MB/s | ~8.0 MB/s |
-------------------------------------------------
6. About eMMC, Sandisk 8GB eMMC on i.MX6DL-sabresd board, CPU @ 792MHZ,
eMMC running at 8 bit, DDR52 @ 52MHZ.
Performance with and without this patch:
-------------------------------------------------
| | read speed | write speed |
|------------------------------------------------
| with this patch | ~37.3 MB/s | ~10.5 MB/s |
|------------------------------------------------
|without this patch | ~33.4 MB/s | ~10.5 MB/s |
-------------------------------------------------
Signed-off-by: Haibo Chen <haibo.chen@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The bounce buffer, used for misaligned bytes for ADMA access,
resides wholly within the (align_sz)-aligned word, just by construction.
The page addresses are aligned to (align_sz), either for 4 or 8 bytes
alignment, so that the aligned word resides wholly within a single page
and can't cross the page boundary. So, the bounce buffer can't cross
the page boundary too. That's why the warnings are never hit, and can
be safely removed.
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Instead of having a local hack taking care of sending the tuning
command and as well to verify the response pattern, let's convert to
the common mmc_send_tuning() API.
This change affects the Exynos variant, since it's the only one which
support the dw_mmc's ->execute_tuning() callback.
It's seems like dw_mmc internal logic expects failed data transfers to
be ended using a stop command. Let the tuning requests also fall into
this category, since there are data transfer involved.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Previously the pm_runtime_put() caused the device to be runtime PM
suspended, but then immediately being resumed when we add the host.
Prevent this unnecessary runtime PM suspend/resume cycle during
->probe() by moving the call to pm_runtime_put() after mmc_add_host().
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
By configure runtime PM prior we enable the use of it, we close the gap
for strange and unhandled conditions. Moreover it makes us rely on the
driver core, after finalized ->probe(), to request an inactive device
to become runtime PM idle/suspended, which earlier potentially could
happen already at pm_runtime_set_autosuspend_delay().
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Since sdhci_remove_host() access the device, we need to make sure it's
runtime PM resumed.
To handle clock gating properly in remove, we first have to make sure
the clocks are ungated.
To fix both these issues, by invoking pm_runtime_get_sync() early in
->remove() callback. Later once we disabled runtime PM, we can restore
the usage count.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Since commit ab78029ecc (drivers/pinctrl: grab default handles from device
core), we can rely on device core for setting the default pins.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Modify transfer mode for support sdio card,
send cmd and data at the same time for read data transfer,
but send data after cmd for write data transfer.
Signed-off-by: Micky Ching <micky_ching@realsil.com.cn>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To support sdio card, transfer mode need make a change,
this need to split code and use it in different place,
Add new function to simplify repeat operation.
Signed-off-by: Micky Ching <micky_ching@realsil.com.cn>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
host->cookie is used for handle async request,
we should init it to negative value when new card inserted,
make cookie value invalid.
Signed-off-by: Micky Ching <micky_ching@realsil.com.cn>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add a new function to dump register within a range.
We print 1 register a line before this patch,
this may make debug info too long when we add more register to dump.
The new dump_reg_range() dump to 8 register a line,
and it is easy to use.
Signed-off-by: Micky Ching <micky_ching@realsil.com.cn>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The MMC core makes use of the devm_* functions while requesting the
CD/WP GPIOs, let's rely on that.
Cc: Barry Song <baohua@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The MMC core makes use of the devm_* functions while requesting the
CD/WP GPIOs, let's rely on that.
Cc: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
At errors, balance sdhci_pltfm_init() with sdhci_pltfm_free(), to make
sure all data is freed properly.
Cc: Srinivas Kandagatla <srinivas.kandagatla@gmail.com>
Cc: Maxime Coquelin <maxime.coquelin@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Since mmc_of_parse() may fail, let's deal with it and thus do proper
error handling.
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Since mmc_of_parse() may fail, let's deal with it and thus do proper
error handling.
Cc: Christian Daudt <bcm@fixthebug.org>
Cc: Matt Porter <mporter@linaro.org>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Since mmc_of_parse() may fail, let's deal with it and thus do proper
error handling.
Cc: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Move exynos related definition to header file. And this
also changes some of the registers name to match the standard
naming convention.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
[Alim: updated the commit message]
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Even though 1MB is reserved for descriptor table in IDMAC,
the dw_mmc host driver is allowed to receive only maximum
128KB block length in one request. This is caused by setting
improper max_blk_count. It needs to be e adjusted so that
descriptor table is used fully. It is found that the performance
is improved with the increased the max_blk_count.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Static checkers complain about the inconsistent NULL checking here:
drivers/mmc/host/mxs-mmc.c:680 mxs_mmc_probe()
warn: variable dereferenced before check 'ssp->dmach' (see line 660)
The variable can't actually be NULL so we can remove the check.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Removing a relict from reverse engineering of the Android driver code
in sunxi_mmc_clk_set_rate.
Signed-off-by: David Lanzendörfer <david.lanzendoerfer@o2s.ch>
Reported-by: <lixiang@allwinnertech.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fixing the register name in sunxi_mmc_reset_host since the
SDXC_HARDWARE_RESET bit is actually located within REG_GCTRL and not
REG_CMDR as it was pointed out by Allwinner.
Signed-off-by: David Lanzendörfer <david.lanzendoerfer@o2s.ch>
Reported-by: <lixiang@allwinnertech.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
1) Adding a comment in order to clarify the choice of the locks within
sunxi_mmc_handle_manual_stop
2) As <lixiang@allwinnertech.com> has pointed out the wait_dma variable
was not accessed within the spin lock block in sunxi_mmc_request and so
(even if it should never happend) it would have theoretically been
possible that some other function would access the variable at the same
time as the function. This has been changed now and the function is
using local variables outside the lock and copys the value over during
the lock phase.
Signed-off-by: David Lanzendörfer <david.lanzendoerfer@o2s.ch>
Reported-by: <lixiang@allwinnertech.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The last descriptor might be the first descriptor as well, so use masking to
add the LD (last descriptor) bit and drop the DIC (disable interrupt on
completion) bit rather then hard assignment as hard assignment will override
the FD (first descriptor) bit if there is only 1 descriptor.
Also set the ER (end of ring) bit and clear buf_addr_ptr2 on the last
descriptor, like the android kernel code does.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: David Lanzendörfer <david.lanzendoerfer@o2s.ch>
Reported-by: <lixiang@allwinnertech.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The only function of these 'prepare' and 'complete' is to
disable the 'card detect' irq during suspend.
The commit which added this,
commit a48ce884d5
mmc: omap_hsmmc: Introduce omap_hsmmc_prepare/complete
justified it by the need to avoid the registration of new devices
during suspend.
However mmc_pm_notify will set ->rescan_disable in the 'prepare'
stage and clear it in the 'complete' stage, so no card detection
will actually happen.
Also the interrupt will be disabled before final suspend as part
of common suspend processing.
So this disabling of the interrupt is unnecessary, and interferes
with a transition to using common code for card-detect management.
Cc: Felipe Balbi <balbi@ti.com>
Cc: Venkatraman S <svenkatr@ti.com>
Cc: Chris Ball <cjb@laptop.org>
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use the module_pci_driver() macro to make the code simpler
by eliminating module_init and module_exit calls.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The commit 0718e59ae2 ("mmc: sdhci: move FSL ESDHC reset handling quirk into
esdhc code") states that Freescale esdhc is the only controller which needs
the interrupt registers restored after a reset. So it moves
SDHCI_QUIRK_RESTORE_IRQS_AFTER_RESET quirk handling code into the
esdhc-imx driver only. Unfortunately the same controller is used in
other boards which use the of-esdhc driver instead (like powerpc P2020).
Restore interrupts after reset in the sdhci-of-esdhc driver also.
Signed-off-by: Alessio Igor Bogani <alessio.bogani@elettra.eu>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add manual tuning function in CSR atlas7 SoC. It is mainly used
for the UHS-I SD card working SDR50 SDR104 mode.
The tuning principle can be seen in SD spec part1 v3.01 4.2.4.5
(tuning command).
SD host send the cmd19 and set the delay value(0-127).
and the sdcard return 64 bytes data. If the data is same with
the tuning data. The delay value is valid. Execute this commmand
128 times. And calculate the longest window of the valid values.
The value in the middle of this window is the best value.
Signed-off-by: Minda Chen <Minda.Chen@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We're running into cases where our enabling of the SDIO interrupt in
dw_mmc doesn't actually take effect. Specifically, adding patch like
this:
+++ b/drivers/mmc/host/dw_mmc.c
@@ -1076,6 +1076,9 @@ static void dw_mci_enable_sdio_irq(struct mmc_host *mmc, int enb)
mci_writel(host, INTMASK,
(int_mask | SDMMC_INT_SDIO(slot->id)));
+ int_mask = mci_readl(host, INTMASK);
+ if (!(int_mask & SDMMC_INT_SDIO(slot->id)))
+ dev_err(&mmc->class_dev, "failed to enable sdio irq\n");
} else {
...actually triggers the error message. That's because the
dw_mci_enable_sdio_irq() unsafely does a read-modify-write of the
INTMASK register.
We can't just use the standard host->lock since that lock is not irq
safe and mmc_signal_sdio_irq() (called from interrupt context) calls
dw_mci_enable_sdio_irq(). Add a new irq-safe lock to protect INTMASK.
An alternate solution to this is to punt mmc_signal_sdio_irq() to the
tasklet and then protect INTMASK modifications by the standard host
lock. This seemed like a bit more of a high-latency change.
Reported-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In the patch (9623b5b mmc: dw_mmc: Disable low power mode if SDIO
interrupts are used) I added code that disabled the low power mode of
dw_mmc when SDIO interrupts are used. That code worked but always
felt a little hacky because we ended up disabling low power as a side
effect of the first enable_sdio_irq() call. That wouldn't be so bad
except that disabling low power involves a complicated process of
writing to the CMD/CMDARG registers and that extra process makes it
difficult to cleanly the read-modify-write race in
dw_mci_enable_sdio_irq() (see future patch in the series).
Change the code to take advantage of the init_card() callback of the
mmc core to do this right at bootup.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Now that we have proper support to use the generic phase API in our clock
driver, switch the MMC driver to use it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: David Lanzendörfer <david.lanzendoerfer@o2s.ch>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Chen-Yu Tsai <wens@csie.org>
Host controllers lacking the required internal vmmc regulator may still
follow the spec with regard to the LSB of SDHCI_POWER_CONTROL. Set the
SDHCI_POWER_ON bit when vmmc is enabled to encourage the controller to
to drive CMD, DAT, SDCLK.
This fixes a regression observed on some Qualcomm and Nvidia boards
caused by 5222161 mmc: sdhci: Improve external VDD regulator support.
Fixes: 52221610dd (mmc: sdhci: Improve external VDD regulator support)
Signed-off-by: Tim Kryger <tim.kryger@gmail.com>
Tested-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Sleep in atomic context happened on Trats2 board after inserting or
removing SD card because mmc_gpio_get_cd() was called under spin lock.
Fix this by moving card detection earlier, before acquiring spin lock.
The mmc_gpio_get_cd() call does not have to be protected by spin lock
because it does not access any sdhci internal data.
The sdhci_do_get_cd() call access host flags (SDHCI_DEVICE_DEAD). After
moving it out side of spin lock it could theoretically race with driver
removal but still there is no actual protection against manual card
eject.
Dmesg after inserting SD card:
[ 41.663414] BUG: sleeping function called from invalid context at drivers/gpio/gpiolib.c:1511
[ 41.670469] in_atomic(): 1, irqs_disabled(): 128, pid: 30, name: kworker/u8:1
[ 41.677580] INFO: lockdep is turned off.
[ 41.681486] irq event stamp: 61972
[ 41.684872] hardirqs last enabled at (61971): [<c0490ee0>] _raw_spin_unlock_irq+0x24/0x5c
[ 41.693118] hardirqs last disabled at (61972): [<c04907ac>] _raw_spin_lock_irq+0x18/0x54
[ 41.701190] softirqs last enabled at (61648): [<c0026fd4>] __do_softirq+0x234/0x2c8
[ 41.708914] softirqs last disabled at (61631): [<c00273a0>] irq_exit+0xd0/0x114
[ 41.716206] Preemption disabled at:[< (null)>] (null)
[ 41.721500]
[ 41.722985] CPU: 3 PID: 30 Comm: kworker/u8:1 Tainted: G W 3.18.0-rc5-next-20141121 #883
[ 41.732111] Workqueue: kmmcd mmc_rescan
[ 41.735945] [<c0014d2c>] (unwind_backtrace) from [<c0011c80>] (show_stack+0x10/0x14)
[ 41.743661] [<c0011c80>] (show_stack) from [<c0489d14>] (dump_stack+0x70/0xbc)
[ 41.750867] [<c0489d14>] (dump_stack) from [<c0228b74>] (gpiod_get_raw_value_cansleep+0x18/0x30)
[ 41.759628] [<c0228b74>] (gpiod_get_raw_value_cansleep) from [<c03646e8>] (mmc_gpio_get_cd+0x38/0x58)
[ 41.768821] [<c03646e8>] (mmc_gpio_get_cd) from [<c036d378>] (sdhci_request+0x50/0x1a4)
[ 41.776808] [<c036d378>] (sdhci_request) from [<c0357934>] (mmc_start_request+0x138/0x268)
[ 41.785051] [<c0357934>] (mmc_start_request) from [<c0357cc8>] (mmc_wait_for_req+0x58/0x1a0)
[ 41.793469] [<c0357cc8>] (mmc_wait_for_req) from [<c0357e68>] (mmc_wait_for_cmd+0x58/0x78)
[ 41.801714] [<c0357e68>] (mmc_wait_for_cmd) from [<c0361c00>] (mmc_io_rw_direct_host+0x98/0x124)
[ 41.810480] [<c0361c00>] (mmc_io_rw_direct_host) from [<c03620f8>] (sdio_reset+0x2c/0x64)
[ 41.818641] [<c03620f8>] (sdio_reset) from [<c035a3d8>] (mmc_rescan+0x254/0x2e4)
[ 41.826028] [<c035a3d8>] (mmc_rescan) from [<c003a0e0>] (process_one_work+0x180/0x3f4)
[ 41.833920] [<c003a0e0>] (process_one_work) from [<c003a3bc>] (worker_thread+0x34/0x4b0)
[ 41.841991] [<c003a3bc>] (worker_thread) from [<c003fed8>] (kthread+0xe4/0x104)
[ 41.849285] [<c003fed8>] (kthread) from [<c000f268>] (ret_from_fork+0x14/0x2c)
[ 42.038276] mmc0: new high speed SDHC card at address 1234
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Fixes: 94144a465d ("mmc: sdhci: add get_cd() implementation")
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In commit 5491ce3f79 ("mmc: sdhci-pxav3: add support for the Armada
38x SDHCI controller"), the sdhci-pxav3 driver was extended to include
support for the SDHCI controller found in the Armada 38x
processor. This mainly involved adding some MBus window related
configuration.
However, this configuration is currently done too early in ->probe():
it is done before clocks are enabled, while this configuration
involves touching the registers of the controller, which will hang the
SoC if the clock is disabled. It wasn't noticed until now because the
bootloader typically leaves gatable clocks enabled, but in situations
where we have a deferred probe (due to a CD GPIO that cannot be taken,
for example), then the probe will be re-tried later, after a clock
disable has been done in the exit path of the failed probe attempt of
the device. This second probe() will hang the system due to the clock
being disabled.
This can for example be produced on Armada 385 GP, which has a CD GPIO
connected to an I2C PCA9555. If the driver for the PCA9555 is not
compiled into the kernel, then we will have the following sequence of
events:
1. The SDHCI probes
2. It does the MBus configuration (which works, because the clock is
left enabled by the bootloader)
3. It enables the clock
4. It tries to get the CD GPIO, which fails due to the driver being
missing, so -EPROBE_DEFER is returned.
5. Before returning -EPROBE_DEFER, the driver cleans up what was
done, which includes disabling the clock.
6. Later on, the SDHCI probe is tried again.
7. It does the MBus configuration, which hangs because the clock is
no longer enabled.
This commit does the obvious fix of doing the MBus configuration after
the clock has been enabled by the driver.
Fixes: 5491ce3f79 ("mmc: sdhci-pxav3: add support for the Armada 38x SDHCI controller")
Cc: <stable@vger.kernel.org> # v3.15+
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Re-tuning for HS400 mode must be done in HS200
mode. Currently there is no support for that.
That needs to be reflected in the code.
Specifically, if tuning is executed in HS400 mode
then return an error, and do not start the
tuning timer if HS200 tuning is being done prior
to switching to HS400.
Note that periodic re-tuning is not expected
to be needed for HS400 but re-tuning is still
needed after the host controller has lost power.
In the case of suspend/resume that is not necessary
because the card is fully re-initialised. That
just leaves runtime suspend/resume with no support
for HS400 re-tuning.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The tuning timer is always used if the tuning mode
is 1 and there is a tuning count, irrespective of
whether this is the first call, or any subsequent
call. Consequently the logic to start the timer
can be simplified.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
A 'goto' can be used to save duplicating unlocking
and returning.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Re-tuning requires that the maximum data length
is limited to 4MiB. The code currently changes
max_blk_count in an attempt to achieve that.
This is wrong because max_blk_count is a different
limit, but it is also un-necessary because
max_req_size is 512KiB anyway. Consequently, the
changes to max_blk_count are removed and the
comment for max_req_size adjusted accordingly.
The comment is also tweaked to show that the 512KiB
limit is a SDMA limit not an ADMA limit.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
- Fix a regression in leds-gpio introduced by a recent commit that
inadvertently changed the name of one of the properties used by
the driver (Fabio Estevam).
- Fix a regression in the ACPI backlight driver introduced by a
recent fix that missed one special case that had to be taken
into account (Aaron Lu).
- Drop the level of some new kernel messages from the ACPI core
introduced by a recent commit to KERN_DEBUG which they should
have used from the start and drop some other unuseful KERN_ERR
messages printed by ACPI (Rafael J Wysocki).
- Revert an incorrect commit modifying the cpupower tool
(Prarit Bhargava).
- Fix two regressions introduced by recent commits in the OPP
library and clean up some existing minor issues in that code
(Viresh Kumar).
- Continue to replace CONFIG_PM_RUNTIME with CONFIG_PM throughout
the tree (or drop it where that can be done) in order to make
it possible to eliminate CONFIG_PM_RUNTIME (Rafael J Wysocki,
Ulf Hansson, Ludovic Desroches). There will be one more
"CONFIG_PM_RUNTIME removal" batch after this one, because some
new uses of it have been introduced during the current merge
window, but that should be sufficient to finally get rid of it.
- Make the ACPI EC driver more robust against race conditions
related to GPE handler installation failures (Lv Zheng).
- Prevent the ACPI device PM core code from attempting to
disable GPEs that it has not enabled which confuses ACPICA
and makes it report errors unnecessarily (Rafael J Wysocki).
- Add a "force" command line switch to the intel_pstate driver
to make it possible to override the blacklisting of some
systems in that driver if needed (Ethan Zhao).
- Improve intel_pstate code documentation and add a MAINTAINERS
entry for it (Kristen Carlson Accardi).
- Make the ACPI fan driver create cooling device interfaces
witn names that reflect the IDs of the ACPI device objects
they are associated with, except for "generic" ACPI fans
(PNP ID "PNP0C0B"). That's necessary for user space thermal
management tools to be able to connect the fans with the
parts of the system they are supposed to be cooling properly.
From Srinivas Pandruvada.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=5fo2
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.19-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI and power management updates from Rafael Wysocki:
"These are regression fixes (leds-gpio, ACPI backlight driver,
operating performance points library, ACPI device enumeration
messages, cpupower tool), other bug fixes (ACPI EC driver, ACPI device
PM), some cleanups in the operating performance points (OPP)
framework, continuation of CONFIG_PM_RUNTIME elimination, a couple of
minor intel_pstate driver changes, a new MAINTAINERS entry for it and
an ACPI fan driver change needed for better support of thermal
management in user space.
Specifics:
- Fix a regression in leds-gpio introduced by a recent commit that
inadvertently changed the name of one of the properties used by the
driver (Fabio Estevam).
- Fix a regression in the ACPI backlight driver introduced by a
recent fix that missed one special case that had to be taken into
account (Aaron Lu).
- Drop the level of some new kernel messages from the ACPI core
introduced by a recent commit to KERN_DEBUG which they should have
used from the start and drop some other unuseful KERN_ERR messages
printed by ACPI (Rafael J Wysocki).
- Revert an incorrect commit modifying the cpupower tool (Prarit
Bhargava).
- Fix two regressions introduced by recent commits in the OPP library
and clean up some existing minor issues in that code (Viresh
Kumar).
- Continue to replace CONFIG_PM_RUNTIME with CONFIG_PM throughout the
tree (or drop it where that can be done) in order to make it
possible to eliminate CONFIG_PM_RUNTIME (Rafael J Wysocki, Ulf
Hansson, Ludovic Desroches).
There will be one more "CONFIG_PM_RUNTIME removal" batch after this
one, because some new uses of it have been introduced during the
current merge window, but that should be sufficient to finally get
rid of it.
- Make the ACPI EC driver more robust against race conditions related
to GPE handler installation failures (Lv Zheng).
- Prevent the ACPI device PM core code from attempting to disable
GPEs that it has not enabled which confuses ACPICA and makes it
report errors unnecessarily (Rafael J Wysocki).
- Add a "force" command line switch to the intel_pstate driver to
make it possible to override the blacklisting of some systems in
that driver if needed (Ethan Zhao).
- Improve intel_pstate code documentation and add a MAINTAINERS entry
for it (Kristen Carlson Accardi).
- Make the ACPI fan driver create cooling device interfaces witn
names that reflect the IDs of the ACPI device objects they are
associated with, except for "generic" ACPI fans (PNP ID "PNP0C0B").
That's necessary for user space thermal management tools to be able
to connect the fans with the parts of the system they are supposed
to be cooling properly. From Srinivas Pandruvada"
* tag 'pm+acpi-3.19-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (32 commits)
MAINTAINERS: add entry for intel_pstate
ACPI / video: update the skip case for acpi_video_device_in_dod()
power / PM: Eliminate CONFIG_PM_RUNTIME
NFC / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
SCSI / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
ACPI / EC: Fix unexpected ec_remove_handlers() invocations
Revert "tools: cpupower: fix return checks for sysfs_get_idlestate_count()"
tracing / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
x86 / PM: Replace CONFIG_PM_RUNTIME in io_apic.c
PM: Remove the SET_PM_RUNTIME_PM_OPS() macro
mmc: atmel-mci: use SET_RUNTIME_PM_OPS() macro
PM / Kconfig: Replace PM_RUNTIME with PM in dependencies
ARM / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
sound / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
phy / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
video / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
tty / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
spi: Replace CONFIG_PM_RUNTIME with CONFIG_PM
ACPI / PM: Do not disable wakeup GPEs that have not been enabled
ACPI / utils: Drop error messages from acpi_evaluate_reference()
...
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
The currently used SET_PM_RUNTIME_PM_OPS() macro is defined to the
SET_RUNTIME_PM_OPS() macro. Convert to the later, since that's the
proper one to use.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This time we have some more new material than we used to have during
the last couple of development cycles.
The most important part of it to me is the introduction of a unified
interface for accessing device properties provided by platform
firmware. It works with Device Trees and ACPI in a uniform way and
drivers using it need not worry about where the properties come
from as long as the platform firmware (either DT or ACPI) makes
them available. It covers both devices and "bare" device node
objects without struct device representation as that turns out to
be necessary in some cases. This has been in the works for quite
a few months (and development cycles) and has been approved by
all of the relevant maintainers.
On top of that, some drivers are switched over to the new interface
(at25, leds-gpio, gpio_keys_polled) and some additional changes are
made to the core GPIO subsystem to allow device drivers to manipulate
GPIOs in the "canonical" way on platforms that provide GPIO information
in their ACPI tables, but don't assign names to GPIO lines (in which
case the driver needs to do that on the basis of what it knows about
the device in question). That also has been approved by the GPIO
core maintainers and the rfkill driver is now going to use it.
Second is support for hardware P-states in the intel_pstate driver.
It uses CPUID to detect whether or not the feature is supported by
the processor in which case it will be enabled by default. However,
it can be disabled entirely from the kernel command line if necessary.
Next is support for a platform firmware interface based on ACPI
operation regions used by the PMIC (Power Management Integrated
Circuit) chips on the Intel Baytrail-T and Baytrail-T-CR platforms.
That interface is used for manipulating power resources and for
thermal management: sensor temperature reporting, trip point setting
and so on.
Also the ACPI core is now going to support the _DEP configuration
information in a limited way. Basically, _DEP it supposed to reflect
off-the-hierarchy dependencies between devices which may be very
indirect, like when AML for one device accesses locations in an
operation region handled by another device's driver (usually, the
device depended on this way is a serial bus or GPIO controller).
The support added this time is sufficient to make the ACPI battery
driver work on Asus T100A, but it is general enough to be able to
cover some other use cases in the future.
Finally, we have a new cpufreq driver for the Loongson1B processor.
In addition to the above, there are fixes and cleanups all over the
place as usual and a traditional ACPICA update to a recent upstream
release.
As far as the fixes go, the ACPI LPSS (Low-power Subsystem) driver
for Intel platforms should be able to handle power management of
the DMA engine correctly, the cpufreq-dt driver should interact
with the thermal subsystem in a better way and the ACPI backlight
driver should handle some more corner cases, among other things.
On top of the ACPICA update there are fixes for race conditions
in the ACPICA's interrupt handling code which might lead to some
random and strange looking failures on some systems.
In the cleanups department the most visible part is the series
of commits targeted at getting rid of the CONFIG_PM_RUNTIME
configuration option. That was triggered by a discussion
regarding the generic power domains code during which we realized
that trying to support certain combinations of PM config options
was painful and not really worth it, because nobody would use them
in production anyway. For this reason, we decided to make
CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and that lead to the
conclusion that the latter became redundant and CONFIG_PM could
be used instead of it. The material here makes that replacement
in a major part of the tree, but there will be at least one more
batch of that in the second part of the merge window.
Specifics:
- Support for retrieving device properties information from ACPI
_DSD device configuration objects and a unified device properties
interface for device drivers (and subsystems) on top of that.
As stated above, this works with Device Trees and ACPI and allows
device drivers to be written in a platform firmware (DT or ACPI)
agnostic way. The at25, leds-gpio and gpio_keys_polled drivers
are now going to use this new interface and the GPIO subsystem
is additionally modified to allow device drivers to assign names
to GPIO resources returned by ACPI _CRS objects (in case _DSD is
not present or does not provide the expected data). The changes
in this set are mostly from Mika Westerberg, Rafael J Wysocki,
Aaron Lu, and Darren Hart with some fixes from others (Fabio Estevam,
Geert Uytterhoeven).
- Support for Hardware Managed Performance States (HWP) as described
in Volume 3, section 14.4, of the Intel SDM in the intel_pstate
driver. CPUID is used to detect whether or not the feature is
supported by the processor. If supported, it will be enabled
automatically unless the intel_pstate=no_hwp switch is present in
the kernel command line. From Dirk Brandewie.
- New Intel Broadwell-H ID for intel_pstate (Dirk Brandewie).
- Support for firmware interface based on ACPI operation regions
used by the PMIC chips on the Intel Baytrail-T and Baytrail-T-CR
platforms for power resource control and thermal management
(Aaron Lu).
- Limited support for retrieving off-the-hierarchy dependencies
between devices from ACPI _DEP device configuration objects
and deferred probing support for the ACPI battery driver based
on the _DEP information to make that driver work on Asus T100A
(Lan Tianyu).
- New cpufreq driver for the Loongson1B processor (Kelvin Cheung).
- ACPICA update to upstream revision 20141107 which only affects
tools (Bob Moore).
- Fixes for race conditions in the ACPICA's interrupt handling
code and in the ACPI code related to system suspend and resume
(Lv Zheng and Rafael J Wysocki).
- ACPI core fix for an RCU-related issue in the ioremap() regions
management code that slowed down significantly after CPUs had
been allowed to enter idle states even if they'd had RCU callbakcs
queued and triggered some problems in certain proprietary graphics
driver (and elsewhere). The fix replaces synchronize_rcu() in
that code with synchronize_rcu_expedited() which makes the issue
go away. From Konstantin Khlebnikov.
- ACPI LPSS (Low-Power Subsystem) driver fix to handle power
management of the DMA engine included into the LPSS correctly.
The problem is that the DMA engine doesn't have ACPI PM support
of its own and it simply is turned off when the last LPSS device
having ACPI PM support goes into D3cold. To work around that,
the PM domain used by the ACPI LPSS driver is redesigned so at
least one device with ACPI PM support will be on as long as the
DMA engine is in use. From Andy Shevchenko.
- ACPI backlight driver fix to avoid using it on "Win8-compatible"
systems where it doesn't work and where it was used by default by
mistake (Aaron Lu).
- Assorted minor ACPI core fixes and cleanups from Tomasz Nowicki,
Sudeep Holla, Huang Rui, Hanjun Guo, Fabian Frederick, and
Ashwin Chaugule (mostly related to the upcoming ARM64 support).
- Intel RAPL (Running Average Power Limit) power capping driver
fixes and improvements including new processor IDs (Jacob Pan).
- Generic power domains modification to power up domains after
attaching devices to them to meet the expectations of device
drivers and bus types assuming devices to be accessible at
probe time (Ulf Hansson).
- Preliminary support for controlling device clocks from the
generic power domains core code and modifications of the
ARM/shmobile platform to use that feature (Ulf Hansson).
- Assorted minor fixes and cleanups of the generic power
domains core code (Ulf Hansson, Geert Uytterhoeven).
- Assorted minor fixes and cleanups of the device clocks control
code in the PM core (Geert Uytterhoeven, Grygorii Strashko).
- Consolidation of device power management Kconfig options by making
CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and removing the latter
which is now redundant (Rafael J Wysocki and Kevin Hilman). That
is the first batch of the changes needed for this purpose.
- Core device runtime power management support code cleanup related
to the execution of callbacks (Andrzej Hajda).
- cpuidle ARM support improvements (Lorenzo Pieralisi).
- cpuidle cleanup related to the CPUIDLE_FLAG_TIME_VALID flag and
a new MAINTAINERS entry for ARM Exynos cpuidle (Daniel Lezcano and
Bartlomiej Zolnierkiewicz).
- New cpufreq driver callback (->ready) to be executed when the
cpufreq core is ready to use a given policy object and cpufreq-dt
driver modification to use that callback for cooling device
registration (Viresh Kumar).
- cpufreq core fixes and cleanups (Viresh Kumar, Vince Hsu,
James Geboski, Tomeu Vizoso).
- Assorted fixes and cleanups in the cpufreq-pcc, intel_pstate,
cpufreq-dt, pxa2xx cpufreq drivers (Lenny Szubowicz, Ethan Zhao,
Stefan Wahren, Petr Cvek).
- OPP (Operating Performance Points) framework modification to
allow OPPs to be removed too and update of a few cpufreq drivers
(cpufreq-dt, exynos5440, imx6q, cpufreq) to remove OPPs (added
during initialization) on driver removal (Viresh Kumar).
- Hibernation core fixes and cleanups (Tina Ruchandani and
Markus Elfring).
- PM Kconfig fix related to CPU power management (Pankaj Dubey).
- cpupower tool fix (Prarit Bhargava).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=5dox
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
"This time we have some more new material than we used to have during
the last couple of development cycles.
The most important part of it to me is the introduction of a unified
interface for accessing device properties provided by platform
firmware. It works with Device Trees and ACPI in a uniform way and
drivers using it need not worry about where the properties come from
as long as the platform firmware (either DT or ACPI) makes them
available. It covers both devices and "bare" device node objects
without struct device representation as that turns out to be necessary
in some cases. This has been in the works for quite a few months (and
development cycles) and has been approved by all of the relevant
maintainers.
On top of that, some drivers are switched over to the new interface
(at25, leds-gpio, gpio_keys_polled) and some additional changes are
made to the core GPIO subsystem to allow device drivers to manipulate
GPIOs in the "canonical" way on platforms that provide GPIO
information in their ACPI tables, but don't assign names to GPIO lines
(in which case the driver needs to do that on the basis of what it
knows about the device in question). That also has been approved by
the GPIO core maintainers and the rfkill driver is now going to use
it.
Second is support for hardware P-states in the intel_pstate driver.
It uses CPUID to detect whether or not the feature is supported by the
processor in which case it will be enabled by default. However, it
can be disabled entirely from the kernel command line if necessary.
Next is support for a platform firmware interface based on ACPI
operation regions used by the PMIC (Power Management Integrated
Circuit) chips on the Intel Baytrail-T and Baytrail-T-CR platforms.
That interface is used for manipulating power resources and for
thermal management: sensor temperature reporting, trip point setting
and so on.
Also the ACPI core is now going to support the _DEP configuration
information in a limited way. Basically, _DEP it supposed to reflect
off-the-hierarchy dependencies between devices which may be very
indirect, like when AML for one device accesses locations in an
operation region handled by another device's driver (usually, the
device depended on this way is a serial bus or GPIO controller). The
support added this time is sufficient to make the ACPI battery driver
work on Asus T100A, but it is general enough to be able to cover some
other use cases in the future.
Finally, we have a new cpufreq driver for the Loongson1B processor.
In addition to the above, there are fixes and cleanups all over the
place as usual and a traditional ACPICA update to a recent upstream
release.
As far as the fixes go, the ACPI LPSS (Low-power Subsystem) driver for
Intel platforms should be able to handle power management of the DMA
engine correctly, the cpufreq-dt driver should interact with the
thermal subsystem in a better way and the ACPI backlight driver should
handle some more corner cases, among other things.
On top of the ACPICA update there are fixes for race conditions in the
ACPICA's interrupt handling code which might lead to some random and
strange looking failures on some systems.
In the cleanups department the most visible part is the series of
commits targeted at getting rid of the CONFIG_PM_RUNTIME configuration
option. That was triggered by a discussion regarding the generic
power domains code during which we realized that trying to support
certain combinations of PM config options was painful and not really
worth it, because nobody would use them in production anyway. For
this reason, we decided to make CONFIG_PM_SLEEP select
CONFIG_PM_RUNTIME and that lead to the conclusion that the latter
became redundant and CONFIG_PM could be used instead of it. The
material here makes that replacement in a major part of the tree, but
there will be at least one more batch of that in the second part of
the merge window.
Specifics:
- Support for retrieving device properties information from ACPI _DSD
device configuration objects and a unified device properties
interface for device drivers (and subsystems) on top of that. As
stated above, this works with Device Trees and ACPI and allows
device drivers to be written in a platform firmware (DT or ACPI)
agnostic way. The at25, leds-gpio and gpio_keys_polled drivers are
now going to use this new interface and the GPIO subsystem is
additionally modified to allow device drivers to assign names to
GPIO resources returned by ACPI _CRS objects (in case _DSD is not
present or does not provide the expected data). The changes in
this set are mostly from Mika Westerberg, Rafael J Wysocki, Aaron
Lu, and Darren Hart with some fixes from others (Fabio Estevam,
Geert Uytterhoeven).
- Support for Hardware Managed Performance States (HWP) as described
in Volume 3, section 14.4, of the Intel SDM in the intel_pstate
driver. CPUID is used to detect whether or not the feature is
supported by the processor. If supported, it will be enabled
automatically unless the intel_pstate=no_hwp switch is present in
the kernel command line. From Dirk Brandewie.
- New Intel Broadwell-H ID for intel_pstate (Dirk Brandewie).
- Support for firmware interface based on ACPI operation regions used
by the PMIC chips on the Intel Baytrail-T and Baytrail-T-CR
platforms for power resource control and thermal management (Aaron
Lu).
- Limited support for retrieving off-the-hierarchy dependencies
between devices from ACPI _DEP device configuration objects and
deferred probing support for the ACPI battery driver based on the
_DEP information to make that driver work on Asus T100A (Lan
Tianyu).
- New cpufreq driver for the Loongson1B processor (Kelvin Cheung).
- ACPICA update to upstream revision 20141107 which only affects
tools (Bob Moore).
- Fixes for race conditions in the ACPICA's interrupt handling code
and in the ACPI code related to system suspend and resume (Lv Zheng
and Rafael J Wysocki).
- ACPI core fix for an RCU-related issue in the ioremap() regions
management code that slowed down significantly after CPUs had been
allowed to enter idle states even if they'd had RCU callbakcs
queued and triggered some problems in certain proprietary graphics
driver (and elsewhere). The fix replaces synchronize_rcu() in that
code with synchronize_rcu_expedited() which makes the issue go
away. From Konstantin Khlebnikov.
- ACPI LPSS (Low-Power Subsystem) driver fix to handle power
management of the DMA engine included into the LPSS correctly. The
problem is that the DMA engine doesn't have ACPI PM support of its
own and it simply is turned off when the last LPSS device having
ACPI PM support goes into D3cold. To work around that, the PM
domain used by the ACPI LPSS driver is redesigned so at least one
device with ACPI PM support will be on as long as the DMA engine is
in use. From Andy Shevchenko.
- ACPI backlight driver fix to avoid using it on "Win8-compatible"
systems where it doesn't work and where it was used by default by
mistake (Aaron Lu).
- Assorted minor ACPI core fixes and cleanups from Tomasz Nowicki,
Sudeep Holla, Huang Rui, Hanjun Guo, Fabian Frederick, and Ashwin
Chaugule (mostly related to the upcoming ARM64 support).
- Intel RAPL (Running Average Power Limit) power capping driver fixes
and improvements including new processor IDs (Jacob Pan).
- Generic power domains modification to power up domains after
attaching devices to them to meet the expectations of device
drivers and bus types assuming devices to be accessible at probe
time (Ulf Hansson).
- Preliminary support for controlling device clocks from the generic
power domains core code and modifications of the ARM/shmobile
platform to use that feature (Ulf Hansson).
- Assorted minor fixes and cleanups of the generic power domains core
code (Ulf Hansson, Geert Uytterhoeven).
- Assorted minor fixes and cleanups of the device clocks control code
in the PM core (Geert Uytterhoeven, Grygorii Strashko).
- Consolidation of device power management Kconfig options by making
CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and removing the latter
which is now redundant (Rafael J Wysocki and Kevin Hilman). That
is the first batch of the changes needed for this purpose.
- Core device runtime power management support code cleanup related
to the execution of callbacks (Andrzej Hajda).
- cpuidle ARM support improvements (Lorenzo Pieralisi).
- cpuidle cleanup related to the CPUIDLE_FLAG_TIME_VALID flag and a
new MAINTAINERS entry for ARM Exynos cpuidle (Daniel Lezcano and
Bartlomiej Zolnierkiewicz).
- New cpufreq driver callback (->ready) to be executed when the
cpufreq core is ready to use a given policy object and cpufreq-dt
driver modification to use that callback for cooling device
registration (Viresh Kumar).
- cpufreq core fixes and cleanups (Viresh Kumar, Vince Hsu, James
Geboski, Tomeu Vizoso).
- Assorted fixes and cleanups in the cpufreq-pcc, intel_pstate,
cpufreq-dt, pxa2xx cpufreq drivers (Lenny Szubowicz, Ethan Zhao,
Stefan Wahren, Petr Cvek).
- OPP (Operating Performance Points) framework modification to allow
OPPs to be removed too and update of a few cpufreq drivers
(cpufreq-dt, exynos5440, imx6q, cpufreq) to remove OPPs (added
during initialization) on driver removal (Viresh Kumar).
- Hibernation core fixes and cleanups (Tina Ruchandani and Markus
Elfring).
- PM Kconfig fix related to CPU power management (Pankaj Dubey).
- cpupower tool fix (Prarit Bhargava)"
* tag 'pm+acpi-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (120 commits)
i2c-omap / PM: Drop CONFIG_PM_RUNTIME from i2c-omap.c
dmaengine / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
tools: cpupower: fix return checks for sysfs_get_idlestate_count()
drivers: sh / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
e1000e / igb / PM: Eliminate CONFIG_PM_RUNTIME
MMC / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
MFD / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
misc / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
media / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
input / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
leds: leds-gpio: Fix multiple instances registration without 'label' property
iio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
hsi / OMAP / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
i2c-hid / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
drm / exynos / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
gpio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
hwrandom / exynos / PM: Use CONFIG_PM in #ifdef
block / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
USB / PM: Drop CONFIG_PM_RUNTIME from the USB core
PM: Merge the SET*_RUNTIME_PM_OPS() macros
...
Instead of having a local hack taking care of sending the tuning
command and as well to verify the response pattern, let's convert to
the common mmc_send_tuning() API instead.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Georgi Djakov <gdjakov@mm-sol.com>
Acked-by: Georgi Djakov <gdjakov@mm-sol.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Instead of having a local function taking care of sending the tuning
command, let's use the common mmc_send_tuning() API provided by the mmc
core. In this way the request will be handled as any other request by
sdhci core.
As an effect of this change, the pm_runtime_get_sync() call at
esdhc_prepare_tuning() isn't needed any more.
This patch will also introduce another change in behavior, since before
the response pattern to the tuning command wasn't verified by
sdhci-esdhc-imx. The mmc_send_tuning() does that.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Dong Aisheng <b29396@freescale.com>
Acked-by: Dong Aisheng <b29396@freescale.com>
After commit b2b49ccbdd (PM: Kconfig: Set PM_RUNTIME if PM_SLEEP is
selected) PM_RUNTIME is always set if PM is set, so #ifdef blocks
depending on CONFIG_PM_RUNTIME may now be changed to depend on
CONFIG_PM.
Replace CONFIG_PM_RUNTIME with CONFIG_PM everywhere under
drivers/mmc/.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
The SET_PM_RUNTIME_PM_OPS() and SET_RUNTIME_PM_OPS() macros are
identical except that one of them is not empty for CONFIG_PM set,
while the other one is not empty for CONFIG_PM_RUNTIME set,
respectively.
However, after commit b2b49ccbdd (PM: Kconfig: Set PM_RUNTIME if
PM_SLEEP is selected) PM_RUNTIME is always set if PM is set, so one
of these macros is now redundant.
For this reason, replace SET_PM_RUNTIME_PM_OPS() with
SET_RUNTIME_PM_OPS() everywhere and redefine the SET_PM_RUNTIME_PM_OPS
symbol as SET_RUNTIME_PM_OPS in case new code is starting to use the
macro being removed here.
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Intel host controllers are capable of doing the bus
width test and of waiting while busy, so add the
capability flags.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
BYT host controllers are capable of doing the bus
width test and of waiting while busy, so add the
capability flags.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC actually causes
standard-compliant behaviour by causing the flagging
of the last DMA transfer descriptor as the end
instead of there being an additional nop descriptor
which is flagged as the end. Consequently, it is
better to have the quirk.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC actually causes
standard-compliant behaviour by causing the flagging
of the last DMA transfer descriptor as the end
instead of there being an additional nop descriptor
which is flagged as the end. Consequently, it is
better to have the quirk. Add it for BYT.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
No more use late initcall to manage probing order. Use probe deferring
if needed.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Using __init/__exit attributes can cause several breakages so remove
them.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
All devices with a DMA controller are DT compliant and legacy support
has been removed. For those reasons, some DMA stuff is useless.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The commit, mmc: omap: clarify DDR timing mode between SD-UHS and eMMC,
switched omap_hsmmc to support MMC DDR mode instead of UHS DDR50 mode.
Add UHS DDR50 mode again and this time let's also keep the MMC DDR mode.
Fixes: 5438ad95a5 (mmc: omap: clarify DDR timing mode between SD-UHS and eMMC)
Reported-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
clk_prepare_enable() may fail and in this case we should propagate the error.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If platform_get_irq() fails, it is better to propagate the real error value
instead of a 'fake' one.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
devm_ioremap_resource() already checks if 'iores' is NULL or not, so we can
skip this manual check.
While at it, move platform_get_resource() closer to devm_ioremap_resource() for
better readability.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add support for the DW MMC host found on the Imagination Pistachio SoC.
Like the DW MMC hosts found on SOCFPGA and Rockchip SoCs, the DW MMC
host on Pistachio requires the use of SDMMC_CMD_USE_HOLD_REG.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
By using SIMPLE_DEV_PM_OPS we can make the code smaller and cleaner.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Instead of registering the irq name with the driver's name, it's better to pass
the device name so that we have a more explicit indication as to what mmc
instance the irq is related:
$ cat /proc/interrupts
CPU0
...
26: 6 - 96 80010000.ssp
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit f1d2736c81 (mmc: dw_mmc: control card read threshold) added
dw_mci_ctrl_rd_thld() with an unconditional write to the CDTHRCTL
register at offset 0x100. However before version 240a, the FIFO region
started at 0x100, so the write messes with the FIFO and completely
breaks the driver.
If the version id < 240A, return early from dw_mci_ctl_rd_thld() so as
not to hit this problem.
Fixes: f1d2736c81 (mmc: dw_mmc: control card read threshold)
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: <stable@vger.kernel.org> # v3.13+
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We check for NULL pointers after dereferencing so it's too late. Oddly
enough, Smatch misses this code but complains about the caller passing
NULL pointers to this function:
drivers/mmc/host/toshsd.c:389 toshsd_irq()
error: we previously assumed 'host->cmd' could be null (see line 349)
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
All boards with a dma controller have DT support so using
dma_request_slave_channel_compat is no more needed.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The bit of sdio interrupt is 16 in designware implementation,
but it is 24 on Rockchip SoCs.This patch add sdio_id0 for the
number of slot0 in the SDIO interrupt registers.
Signed-off-by: Addy Ke <addy.ke@rock-chips.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In order to use the mvsdio driver for sdio, it has been necessary to
use a module parameter to disable DMA so to force PIO is used. It is
then possible to use wireless LAN devices like mwifiex found on
topkick and mirabox. However, accessing an MMC SD card does work with
DMA.
Investigation has shown that MMC block device accesses are always
aligned to 64 byte boundaries, where as transfers from mwifiex are
rarely more than word aligned. It has also been determined that card
to host transfers work with DMA for SDIO devices, but host to card
transfers with DMA have problems.
This patch extends the current checks for buffers which are not word
aligned or multiple of words. All host to card transfers which are not
64 byte aligned are now also performed via PIO. This should not affect
the performance of SD cards, but allow sdio devices to work out of the
box, and they are likely to be more efficient since DMA will be used
for card to host transfers.
Tested on mirabox for wifi via mwifiex
Tested on 370 RD for file systems on an SD card.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There are upcoming ARM64 SoCs with dw_mmc host controller.
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch resurrects an old never-finished driver for Toshiba PCI SD
controllers found in some older Toshiba laptops (such as Portege R100):
02:0d.0 System peripheral [0880]: Toshiba America Info Systems SD TypA Controller [1179:0805] (rev 05)
The code is fixed, cleaned up and successfully tested with SD, SDHC, SDXC and
MMC cards on Portege R100. (MMC cards don't even work in Windows!)
SDIO probably does not work (don't have any SDIO card).
The hardware is slow (around 2 MB/s - same in Windows) because it does not
support bus mastering (busmaster enable bit cannot be set in PCI control reg).
Also the card clock is limited to 16MHz (33MHz PCI clock divided by 2).
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The Exynos7 has a DWMMC controller (v2.70a) which is different from
prior versions. This patch adds new compatible strings for exynos7.
This patch also fixes the CLKSEL register offset on exynos7.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Yuvaraj Kumar C D <yuvaraj.cd@samsung.com>
Tested-by: Vivek Gautam <gautam.vivek@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
omap_hsmmc only supports one slot. So slot id is always zero, and
slot id was never used in the callbacks anyway
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
These callbacks are set during driver probe and not from the platform
init, -- evtl. they had been for oamp 1/2 -- for omap3 they are local
functions of the driver. These indirection could be dropped
altogether in favor of regular function calls TODO
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
this is needed when installing callbacks in the host struct and not
in the platform data, e.g. cover detect irq should be stored in
omap_hsmmc_host and not platform data
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
omap_hsmmc supports only one slot per controller, see OMAP_MMC_MAX_SLOTS.
This unnecessary indirection leads to confusion in the omap_hsmmc driver.
For example the card_detect callback is not installed by platform code
but from the driver probe function. So it should be a field of
omap_hsmmc_host. But since it is declared under the platform slot while
the drivers struct omap_hsmmc_host has no slot abstraction, this looks
like a bug, especially when not familiar that this driver only supports
1 slot anyway.
Either we should add a slot abstraction to omap_hsmmc_host or remove
it from the platform data struct. Removed since slot multiplexing is
an un-implemented feature
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
these callbacks are not set, probably legacy omap 1/2 features
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
- omap mmc driver supports multiplexing, omap_mmc_hs doesn't
this leads to one of the major confusions in the omap_hsmmc driver
- platform data should be read-only for the driver
most callbacks are not set by the omap3 platform init code while still
required. So they are set from the driver probe function, which is against
the paradigm that platform-data should not be modified by the driver
typical examples are card_detect, read_only callbacks
un-bundling by searching for driver name \"omap_hsmmc in the
arch/arm folder. omap_hsmmc_platform_data is not initialized directly,
but from omap2_hsmmc_info, which is defined in a separate header file
not touched by this patch
hwmod includes platform headers to declare features of the platform. All
the declared features are prefixed OMAP_HSMMC. There is no need to
include platform header from hwmod other except for feature defines
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Amend the atmel mci pin controller to optionally take a pin control
handle and set the state of the pins to:
- "default" on boot, resume and before performing an transfer.
- "sleep" on suspend().
This should make it possible to optimize energy usage for the pins
both for the suspend/resume cycle.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
MMC core already has support for HS400. Add HS400
support to SDHCI driver. The SDHC Standard specification
does not define HS400 so consequently HS400 support is
non-standard. However HS400 is not selected without
the host controller setting the corresponding capability
flags so host controllers not yet supporting HS400
will not be affected. To support that, a quirk
SDHCI_QUIRK2_CAPS_BIT63_FOR_HS400 is introduced to
enable the use of capabilities register reserved bit-63
to indicate HS400 support.
Because HS400 is non-standard for SDHCI, it is possible
that different vendors will do things in different ways.
However HS200 support faced the same issue but currently
there is only one solution. As such, no attempt has
been made to provide for alternate HS400 solutions except
for SDHCI_QUIRK2_CAPS_BIT63_FOR_HS400.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
1.2V HS200 mode capability is cleared if there is not a voltage
regulator that supports 1.2V. Do the same for 1.2V HS400 mode.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
supply.vqmmc is used with the IS_ERR macro which means
the value must be valid or an error code. NULL is
neither, so replace with ERR_PTR(-EINVAL).
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Synopsys DW_MMC IP core supports Internal DMA Controller with 64-bit address mode from IP version 2.70a onwards.
Updated the driver to support IDMAC 64-bit addressing mode.
Signed-off-by: Prabu Thangamuthu <prabu.t@synopsys.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
AMD SD controller supports the SDR104 mode, but caps2 can not
be promoted to support hs200 for eMMC.
Signed-off-by: Vincent Wan <vincent.wan@amd.com>
Signed-off-by: Wan Zongshun <mcuos.com@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch is to enable the quirk for AMD sdhci requiring transfer
mode register need to be cleared for commands without data
Signed-off-by: Vincent Wan <vincent.wan@amd.com>
Signed-off-by: Wan Zongshun <mcuos.com@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SDHC controller in AMD chipsets require SDHC transfer mode
register to be cleared for commands without data. The issue was
uncovered during testing eMMC cards on KB/ML based platforms
Signed-off-by: Vincent Wan <vincent.wan@amd.com>
Signed-off-by: Wan Zongshun <mcuos.com@gmail.com>
Signed-off-by: Arindam Nath <arindam.nath@amd.com>
Tested-by: Vikram B <vikram.b@amd.com>
Tested-by: Raghavendra Swamy <raghavendra.swamy@amd.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It is possible that we may fail to set the clock rate, if we do so then
log the failure and don't bother reprogramming the IP.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Suman Tripathi