This patchs sets the params for the DWC2 Controller found in the
Amlogic G12A SoC family.
It mainly sets the settings reported incorrect by the driver,
leaving the remaining detected automatically by the driver and
provided by the DT node.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Adds the bindings for the Amlogic G12A USB Glue HW.
The Amlogic G12A SoC Family embeds 2 USB Controllers :
- a DWC3 IP configured as Host for USB2 and USB3
- a DWC2 IP configured as Peripheral USB2 Only
A glue connects these both controllers to 2 USB2 PHYs,
and optionnally to an USB3+PCIE Combo PHY shared with the PCIE controller.
The Glue configures the UTMI 8bit interfaces for the USB2 PHYs, including
routing of the OTG PHY between the DWC3 and DWC2 controllers, and
setups the on-chip OTG mode selection for this PHY.
The PHYs phandles are passed to the Glue node since the Glue controls the
interface with the PHY, not the DWC3 controller.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Adds the specific compatible string for the DWC2 IP found in the
Amlogic G12A SoC Family.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The syzkaller USB fuzzer identified a failure mode in which dummy-hcd
would never give back an unlinked URB. This causes usb_kill_urb() to
hang, leading to WARNINGs and unkillable threads.
In dummy-hcd, all URBs are given back by the dummy_timer() routine as
it scans through the list of pending URBS. Failure to give back URBs
can be caused by failure to start or early exit from the scanning
loop. The code currently has two such pathways: One is triggered when
an unsupported bus transfer speed is encountered, and the other by
exhausting the simulated bandwidth for USB transfers during a frame.
This patch removes those two paths, thereby allowing all unlinked URBs
to be given back in a timely manner. It adds a check for the bus
speed when the gadget first starts running, so that dummy_timer() will
never thereafter encounter an unsupported speed. And it prevents the
loop from exiting as soon as the total bandwidth has been used up (the
scanning loop continues, giving back unlinked URBs as they are found,
but not transferring any more data).
Thanks to Andrey Konovalov for manually running the syzkaller fuzzer
to help track down the source of the bug.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: syzbot+d919b0f29d7b5a4994b9@syzkaller.appspotmail.com
CC: <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Keep EXTCON support optional, as some platforms do not need it.
Do the same for USB_DWC3_OMAP while we're at it.
Fixes: 3def4031b3 ("usb: dwc3: add EXTCON dependency for qcom")
Signed-off-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Highlights include:
Bugfixes:
- Fix a regression in which an RPC call can be tagged with an error despite
the transmission being successful
-----BEGIN PGP SIGNATURE-----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=3T3x
-----END PGP SIGNATURE-----
Merge tag 'nfs-for-5.1-5' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client bugfix from Trond Myklebust:
"Fix a regression in which an RPC call can be tagged with an error
despite the transmission being successful"
* tag 'nfs-for-5.1-5' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
SUNRPC: Ignore queue transmission errors on successful transmission
Three minor fixes: two obvious ones in drivers and a fix to the SG_IO
path to correctly return status on error.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXLtrDSYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishYh/AQDe6Jf7
jU/VKsir8r74Uy1gHw9wXkmcgzKeTzHErEyvGgD9HqEfAKUWr0YlMqfKqnQZUhUc
TPokv5u1u2xc/ba+nuo=
=VutB
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Three minor fixes: two obvious ones in drivers and a fix to the SG_IO
path to correctly return status on error"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: aic7xxx: fix EISA support
Revert "scsi: fcoe: clear FC_RP_STARTED flags when receiving a LOGO"
scsi: core: set result when the command cannot be dispatched
-----BEGIN PGP SIGNATURE-----
iQJEBAABCAAuFiEEwPw5LcreJtl1+l5K99NY+ylx4KYFAly7HukQHGF4Ym9lQGtl
cm5lbC5kawAKCRD301j7KXHgpla6D/9y7YyAyKDgv/pVQgAlDYaGSXufvrK5iK/f
uFdSWPvGuWMbx+xy/4hfSX1pV9ZRv1aRJeFOkL/qVyr+4izKrgevwj+6Kl3/mCUO
dhiqF76bnaGXNQC6YDn1IgZp2Za+WGpeNlEhwcg20Ve11U7DVBhcL/n/6NYphtUG
V7ZFoVw+yjOO9GvkUeHx24HIQdC0JrABMoXYldl/tX3H9WjB3d1ncZDS45TuemXJ
lwm/S4nyaNaDzLnO7Hv51u3tCFpuaJbcgBdKuZB/oSWhU68D26/6peW+8qAvN+ec
htibFrK6KPRQCLNMEaV2njZEyprkL/BZJz4YukwmWB8GAtsuquy3Q3wJPounGmm5
7fCG/T1asqkurwhVcHOC07R6+d8AT5ARyJn3QYFmoYCIoSwObu6xhZHHAv7Ct1Xn
lrU4it0WkYbTXVI1l4CaRUtshCIQTZwr2EsgppjAsBc1+V2KgtbxR1wkQq2q9tQZ
Fa/2KTv9Y1+7FUOf09LEvTbuUgZn4I6u4E07QwY4miFsQSEUufirfHZ5t62lIgA9
3YzUrlVQSP1PbG8IP4aCSX2o+dxhL1Js6ukdZAxM6w9RtjLqWI3zTImSSMJobjna
SF53kkpv1xuJYT+Z1YmNGbMauzLs/HhCB9ww56TUuQYW/rTDASqFc48l7+vsfPrZ
sTEkShVGOw==
=d9Ws
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20190420' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
"A set of small fixes that should go into this series. This contains:
- Removal of unused queue member (Hou)
- Overflow bvec fix (Ming)
- Various little io_uring tweaks (me)
- kthread parking
- Only call cpu_possible() for verified CPU
- Drop unused 'file' argument to io_file_put()
- io_uring_enter vs io_uring_register deadlock fix
- CQ overflow fix
- BFQ internal depth update fix (me)"
* tag 'for-linus-20190420' of git://git.kernel.dk/linux-block:
block: make sure that bvec length can't be overflow
block: kill all_q_node in request_queue
io_uring: fix CQ overflow condition
io_uring: fix possible deadlock between io_uring_{enter,register}
io_uring: drop io_file_put() 'file' argument
bfq: update internal depth state when queue depth changes
io_uring: only test SQPOLL cpu after we've verified it
io_uring: park SQPOLL thread if it's percpu
- Fix the disable controller logic in the designware driver
- Fix I3C entry in MAINTAINERS
-----BEGIN PGP SIGNATURE-----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=RUzG
-----END PGP SIGNATURE-----
Merge tag 'i3c/fixes-for-5.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux
Pill i3c fixes from Boris Brezillon:
- fix the random PID check
- fix the disable controller logic in the designware driver
- fix I3C entry in MAINTAINERS
* tag 'i3c/fixes-for-5.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux:
MAINTAINERS: Fix the I3C entry
i3c: dw: Fix dw_i3c_master_disable controller by using correct mask
i3c: Fix the verification of random PID
Two core fixes for long-standing bugs for the races at concurrent
device creation and deletion that were (unsurprisingly) spotted by
syzkaller with usb-fuzzer. The rest are usual small HD-audio fixes.
-----BEGIN PGP SIGNATURE-----
iQJCBAABCAAsFiEEIXTw5fNLNI7mMiVaLtJE4w1nLE8FAly6ywQOHHRpd2FpQHN1
c2UuZGUACgkQLtJE4w1nLE9uUg//VwKpvt8496LIp74P4C++gfSj2IGdDWR5h2sV
X0YucwUV3ILIQ2lhhAKh8JgxIhsqbNnS0JALLb07/U70GqxUJsVj8gzVGCpoTS0J
cuk9U5+2qh2vUKBYTzu1SQyYAnoCEDsw8vf8aewmfcrjEQJc7Mm2gkD86wAhn01G
pC0yuf5YLqBv1HtsNp9NE6yF9mbPuvgUwC/ZD3YscwXi32vZSEmx/CIjBzYEJ/0p
y56xUxr9MSAmNk7+OVCMftP7v0c7pxpbVyMqF6p9zLrgu9IDBmtK4XBCVv47O/bm
WQApeYdjrGeYzfa1aFuO2d6WbLdHZWvPOrEAkSAaoBevit0rkvUNqfHvRDzBkqgI
KGIhv6NtaM2JVfF/PcEK4dIX2UFe0PWmQXSdBOb4oxXohei+avxE4r3T+O2IX5wF
EY4pPcqY0XQSuRZ4u3MFT7jOZHUQweVQzWEEoE8sWy0tJyKhXvmBVRZ+B0So4SvR
l4z40gvoaVbJc8osKh5UcH8QvCGFTlFwgRVdCZvYBD8YRMf2nsIUFGgj4I2ZZ1M1
4OceaOTqC1KcGPXEJcEAuzOHBVDXyClOXWO+Bvbx2oLGx19J9QNFu+ypcZbrU4xk
zfGtPfTruu5HAjFKchndTFp6LmkPw6tUsQOauBMvwSNIYL+Vl87jRPK5gvoc1bg5
2gpTzwY=
=kpz9
-----END PGP SIGNATURE-----
Merge tag 'sound-5.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Two core fixes for long-standing bugs for the races at concurrent
device creation and deletion that were (unsurprisingly) spotted by
syzkaller with usb-fuzzer.
The rest are usual small HD-audio fixes"
* tag 'sound-5.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda/realtek - add two more pin configuration sets to quirk table
ALSA: core: Fix card races between register and disconnect
ALSA: info: Fix racy addition/deletion of nodes
ALSA: hda: Initialize power_state field properly
Pull perf fixes from Ingo Molnar:
"Misc fixes:
- various tooling fixes
- kretprobe fixes
- kprobes annotation fixes
- kprobes error checking fix
- fix the default events for AMD Family 17h CPUs
- PEBS fix
- AUX record fix
- address filtering fix"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/kprobes: Avoid kretprobe recursion bug
kprobes: Mark ftrace mcount handler functions nokprobe
x86/kprobes: Verify stack frame on kretprobe
perf/x86/amd: Add event map for AMD Family 17h
perf bpf: Return NULL when RB tree lookup fails in perf_env__find_btf()
perf tools: Fix map reference counting
perf evlist: Fix side band thread draining
perf tools: Check maps for bpf programs
perf bpf: Return NULL when RB tree lookup fails in perf_env__find_bpf_prog_info()
tools include uapi: Sync sound/asound.h copy
perf top: Always sample time to satisfy needs of use of ordered queuing
perf evsel: Use hweight64() instead of hweight_long(attr.sample_regs_user)
tools lib traceevent: Fix missing equality check for strcmp
perf stat: Disable DIR_FORMAT feature for 'perf stat record'
perf scripts python: export-to-sqlite.py: Fix use of parent_id in calls_view
perf header: Fix lock/unlock imbalances when processing BPF/BTF info
perf/x86: Fix incorrect PEBS_REGS
perf/ring_buffer: Fix AUX record suppression
perf/core: Fix the address filtering fix
kprobes: Fix error check when reusing optimized probes
Pull x86 fixes from Ingo Molnar:
"Misc fixes all over the place: a console spam fix, section attributes
fixes, a KASLR fix, a TLB stack-variable alignment fix, a reboot
quirk, boot options related warnings fix, an LTO fix, a deadlock fix
and an RDT fix"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/cpu/intel: Lower the "ENERGY_PERF_BIAS: Set to normal" message's log priority
x86/cpu/bugs: Use __initconst for 'const' init data
x86/mm/KASLR: Fix the size of the direct mapping section
x86/Kconfig: Fix spelling mistake "effectivness" -> "effectiveness"
x86/mm/tlb: Revert "x86/mm: Align TLB invalidation info"
x86/reboot, efi: Use EFI reboot for Acer TravelMate X514-51T
x86/mm: Prevent bogus warnings with "noexec=off"
x86/build/lto: Fix truncated .bss with -fdata-sections
x86/speculation: Prevent deadlock on ssb_state::lock
x86/resctrl: Do not repeat rdtgroup mode initialization
Pull scheduler fixes from Ingo Molnar:
"A deadline scheduler warning/race fix, and a cfs_period_us quota
calculation workaround where the real fix looks too involved to merge
immediately"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/deadline: Correctly handle active 0-lag timers
sched/fair: Limit sched_cfs_period_timer() loop to avoid hard lockup
Pull locking fixes from Ingo Molnar:
"A lockdep warning fix and a script execution fix when atomics are
generated"
* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
locking/atomics: Don't assume that scripts are executable
locking/lockdep: Make lockdep_unregister_key() honor 'debug_locks' again
Pull cgroup fix from Tejun Heo:
"A patch to fix a RCU imbalance error in the devices cgroup
configuration error path"
* 'for-5.1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
device_cgroup: fix RCU imbalance in error case
Pull percpu fixlet from Dennis Zhou:
"This stops printing the base address of percpu memory on
initialization"
* 'for-5.1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/dennis/percpu:
percpu: stop printing kernel addresses
Here are 5 small fixes for some tty/serial/vt issues that have been
reported.
The vt one has been around for a while, it is good to finally get that
resolved. The others fix a build warning that showed up in 5.1-rc1, and
resolve a problem in the sh-sci driver.
Note, the second patch for build warning fix for the sc16is7xx driver
was just applied to the tree, as it resolves a problem with the previous
patch to try to solve the issue. It has not shown up in linux-next yet,
unlike all of the other patches, but it has passed 0-day testing and
everyone seems to agree that it is correct.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXLoeMg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yll3gCfdfclnKAQt7UnXUZccT7f6oebB6gAoLEy0NEi
lDl7inafWImRKCRq1+zw
=Qk9s
-----END PGP SIGNATURE-----
Merge tag 'tty-5.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are five small fixes for some tty/serial/vt issues that have been
reported.
The vt one has been around for a while, it is good to finally get that
resolved. The others fix a build warning that showed up in 5.1-rc1,
and resolve a problem in the sh-sci driver.
Note, the second patch for build warning fix for the sc16is7xx driver
was just applied to the tree, as it resolves a problem with the
previous patch to try to solve the issue. It has not shown up in
linux-next yet, unlike all of the other patches, but it has passed
0-day testing and everyone seems to agree that it is correct"
* tag 'tty-5.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
sc16is7xx: put err_spi and err_i2c into correct #ifdef
vt: fix cursor when clearing the screen
sc16is7xx: move label 'err_spi' to correct section
serial: sh-sci: Fix HSCIF RX sampling point adjustment
serial: sh-sci: Fix HSCIF RX sampling point calculation
Merge misc fixes from Andrew Morton:
"16 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
coredump: fix race condition between mmget_not_zero()/get_task_mm() and core dumping
mm/kmemleak.c: fix unused-function warning
init: initialize jump labels before command line option parsing
kernel/watchdog_hld.c: hard lockup message should end with a newline
kcov: improve CONFIG_ARCH_HAS_KCOV help text
mm: fix inactive list balancing between NUMA nodes and cgroups
mm/hotplug: treat CMA pages as unmovable
proc: fixup proc-pid-vm test
proc: fix map_files test on F29
mm/vmstat.c: fix /proc/vmstat format for CONFIG_DEBUG_TLBFLUSH=y CONFIG_SMP=n
mm/memory_hotplug: do not unlock after failing to take the device_hotplug_lock
mm: swapoff: shmem_unuse() stop eviction without igrab()
mm: swapoff: take notice of completion sooner
mm: swapoff: remove too limiting SWAP_UNUSE_MAX_TRIES
mm: swapoff: shmem_find_swap_entries() filter out other types
slab: store tagged freelist for off-slab slabmgmt
Here is a bunch of IIO driver fixes, and some smaller staging driver
fixes, for 5.1-rc6. The IIO fixes were delayed due to my vacation, but
all resolve a number of reported issues and have been in linux-next for
a few weeks with no reported issues.
The other staging driver fixes are all tiny, resolving some reported
issues in the comedi and most drivers, as well as some erofs fixes.
All of these patches have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXLm7QA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylqDgCgwt+6SUTrkHCrwfiSEIyY0gXBnZsAoKrNjd1Y
VvbBiG9lk0ST1V/vWrkJ
=Njex
-----END PGP SIGNATURE-----
Merge tag 'staging-5.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging and IIO fixes from Greg KH:
"Here is a bunch of IIO driver fixes, and some smaller staging driver
fixes, for 5.1-rc6. The IIO fixes were delayed due to my vacation, but
all resolve a number of reported issues and have been in linux-next
for a few weeks with no reported issues.
The other staging driver fixes are all tiny, resolving some reported
issues in the comedi and most drivers, as well as some erofs fixes.
All of these patches have been in linux-next with no reported issues"
* tag 'staging-5.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (24 commits)
staging: comedi: ni_usb6501: Fix possible double-free of ->usb_rx_buf
staging: comedi: ni_usb6501: Fix use of uninitialized mutex
staging: erofs: fix unexpected out-of-bound data access
staging: comedi: vmk80xx: Fix possible double-free of ->usb_rx_buf
staging: comedi: vmk80xx: Fix use of uninitialized semaphore
staging: most: core: use device description as name
iio: core: fix a possible circular locking dependency
iio: ad_sigma_delta: select channel when reading register
iio: pms7003: select IIO_TRIGGERED_BUFFER
iio: cros_ec: Fix the maths for gyro scale calculation
iio: adc: xilinx: prevent touching unclocked h/w on remove
iio: adc: xilinx: fix potential use-after-free on probe
iio: adc: xilinx: fix potential use-after-free on remove
iio: dac: mcp4725: add missing powerdown bits in store eeprom
io: accel: kxcjk1013: restore the range after resume.
iio:chemical:bme680: Fix SPI read interface
iio:chemical:bme680: Fix, report temperature in millidegrees
iio: chemical: fix missing Kconfig block for sgp30
iio: adc: at91: disable adc channel interrupt in timeout case
iio: gyro: mpu3050: fix chip ID reading
...
Here are 4 small misc driver fixes for 5.1-rc6.
Nothing major at all, they fix up a Kconfig issues, a SPDX invalid
license tag, and 2 tiny bugfixes.
All have been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXLm6yw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykBXQCgok0WblimRO9jTDQul7JXTxwZyxMAoMU841gi
WPjtj2t1aqbxn8IdJPP/
=bIbF
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc fixes from Greg KH:
"Here are four small misc driver fixes for 5.1-rc6.
Nothing major at all, they fix up a Kconfig issues, a SPDX invalid
license tag, and two tiny bugfixes.
All have been in linux-next for a while with no reported issues"
* tag 'char-misc-5.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
drivers: power: supply: goldfish_battery: Fix bogus SPDX identifier
extcon: ptn5150: fix COMPILE_TEST dependencies
misc: fastrpc: add checked value for dma_set_mask
habanalabs: remove low credit limit of DMA #0
bvec->bv_offset may be bigger than PAGE_SIZE sometimes, such as,
when one bio is splitted in the middle of one bvec via bio_split(),
and bi_iter.bi_bvec_done is used to build offset of the 1st bvec of
remained bio. And the remained bio's bvec may be re-submitted to fs
layer via ITER_IBVEC, such as loop and nvme-loop.
So we have to make sure that every bvec's offset is less than
PAGE_SIZE from bio_for_each_segment_all() because some drivers(loop,
nvme-loop) passes the splitted bvec to fs layer via ITER_BVEC.
This patch fixes this issue reported by Zhang Yi When running nvme/011.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Yi Zhang <yi.zhang@redhat.com>
Reported-by: Yi Zhang <yi.zhang@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Fixes: 6dc4f100c1 ("block: allow bio_for_each_segment_all() to iterate over multi-page bvec")
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
all_q_node has not been used since commit 4b855ad371 ("blk-mq: Create
hctx for each present CPU"), so remove it.
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Hou Tao <houtao1@huawei.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pull input updates from Dmitry Torokhov:
- several new key mappings for HID
- a host of new ACPI IDs used to identify Elan touchpads in Lenovo
laptops
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: snvs_pwrkey - initialize necessary driver data before enabling IRQ
HID: input: add mapping for "Toggle Display" key
HID: input: add mapping for "Full Screen" key
HID: input: add mapping for keyboard Brightness Up/Down/Toggle keys
HID: input: add mapping for Expose/Overview key
HID: input: fix mapping of aspect ratio key
[media] doc-rst: switch to new names for Full Screen/Aspect keys
Input: document meanings of KEY_SCREEN and KEY_ZOOM
Input: elan_i2c - add hardware ID for multiple Lenovo laptops
The "ENERGY_PERF_BIAS: Set to 'normal', was 'performance'" message triggers
on pretty much every Intel machine. The purpose of log messages with
a warning level is to notify the user of something which potentially is
a problem, or at least somewhat unexpected.
This message clearly does not match those criteria, so lower its log
priority from warning to info.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20181230172715.17469-1-hdegoede@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
perf top:
Jiri Olsa:
- Fix 'perf top --pid', it needs PERF_SAMPLE_TIME since we switched to using
a different thread to sort the events and then even for just a single
thread we now need timestamps.
BPF:
Jiri Olsa:
- Fix bpf_prog and btf lookup functions failure path to to properly return
NULL.
- Fix side band thread draining, used to process PERF_RECORD_BPF_EVENT
metadata records.
core:
Jiri Olsa:
- Fix map lookup by name to get a refcount when the name is already in
the tree. Found
Song Liu:
- Fix __map__is_kmodule() by taking into account recently added BPF
maps.
UAPI:
Arnaldo Carvalho de Melo:
- Sync sound/asound.h copy
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQR2GiIUctdOfX2qHhGyPKLppCJ+JwUCXLm+cgAKCRCyPKLppCJ+
J7QCAQCtI0NIeLUKY/o0vITBvCeKi5R1NNkE/A8ZhTzWD9UApwEA0eqoNHsOmIUG
tFRCYi3hPByvtgjIRXvrCm0gpUfFdAo=
=/siq
-----END PGP SIGNATURE-----
Merge tag 'perf-urgent-for-mingo-5.1-20190419' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/urgent
Pull perf/urgent fixes from Arnaldo Carvalho de Melo:
perf top:
Jiri Olsa:
- Fix 'perf top --pid', it needs PERF_SAMPLE_TIME since we switched to using
a different thread to sort the events and then even for just a single
thread we now need timestamps.
BPF:
Jiri Olsa:
- Fix bpf_prog and btf lookup functions failure path to to properly return
NULL.
- Fix side band thread draining, used to process PERF_RECORD_BPF_EVENT
metadata records.
core:
Jiri Olsa:
- Fix map lookup by name to get a refcount when the name is already in
the tree. Found
Song Liu:
- Fix __map__is_kmodule() by taking into account recently added BPF
maps.
UAPI:
Arnaldo Carvalho de Melo:
- Sync sound/asound.h copy
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The core dumping code has always run without holding the mmap_sem for
writing, despite that is the only way to ensure that the entire vma
layout will not change from under it. Only using some signal
serialization on the processes belonging to the mm is not nearly enough.
This was pointed out earlier. For example in Hugh's post from Jul 2017:
https://lkml.kernel.org/r/alpine.LSU.2.11.1707191716030.2055@eggly.anvils
"Not strictly relevant here, but a related note: I was very surprised
to discover, only quite recently, how handle_mm_fault() may be called
without down_read(mmap_sem) - when core dumping. That seems a
misguided optimization to me, which would also be nice to correct"
In particular because the growsdown and growsup can move the
vm_start/vm_end the various loops the core dump does around the vma will
not be consistent if page faults can happen concurrently.
Pretty much all users calling mmget_not_zero()/get_task_mm() and then
taking the mmap_sem had the potential to introduce unexpected side
effects in the core dumping code.
Adding mmap_sem for writing around the ->core_dump invocation is a
viable long term fix, but it requires removing all copy user and page
faults and to replace them with get_dump_page() for all binary formats
which is not suitable as a short term fix.
For the time being this solution manually covers the places that can
confuse the core dump either by altering the vma layout or the vma flags
while it runs. Once ->core_dump runs under mmap_sem for writing the
function mmget_still_valid() can be dropped.
Allowing mmap_sem protected sections to run in parallel with the
coredump provides some minor parallelism advantage to the swapoff code
(which seems to be safe enough by never mangling any vma field and can
keep doing swapins in parallel to the core dumping) and to some other
corner case.
In order to facilitate the backporting I added "Fixes: 86039bd3b4e6"
however the side effect of this same race condition in /proc/pid/mem
should be reproducible since before 2.6.12-rc2 so I couldn't add any
other "Fixes:" because there's no hash beyond the git genesis commit.
Because find_extend_vma() is the only location outside of the process
context that could modify the "mm" structures under mmap_sem for
reading, by adding the mmget_still_valid() check to it, all other cases
that take the mmap_sem for reading don't need the new check after
mmget_not_zero()/get_task_mm(). The expand_stack() in page fault
context also doesn't need the new check, because all tasks under core
dumping are frozen.
Link: http://lkml.kernel.org/r/20190325224949.11068-1-aarcange@redhat.com
Fixes: 86039bd3b4 ("userfaultfd: add new syscall to provide memory externalization")
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Reported-by: Jann Horn <jannh@google.com>
Suggested-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Mike Rapoport <rppt@linux.ibm.com>
Reviewed-by: Oleg Nesterov <oleg@redhat.com>
Reviewed-by: Jann Horn <jannh@google.com>
Acked-by: Jason Gunthorpe <jgg@mellanox.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The only references outside of the #ifdef have been removed, so now we
get a warning in non-SMP configurations:
mm/kmemleak.c:1404:13: error: unused function 'scan_large_block' [-Werror,-Wunused-function]
Add a new #ifdef around it.
Link: http://lkml.kernel.org/r/20190416123148.3502045-1-arnd@arndb.de
Fixes: 298a32b132 ("kmemleak: powerpc: skip scanning holes in the .bss section")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Vincent Whitchurch <vincent.whitchurch@axis.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When a module option, or core kernel argument, toggles a static-key it
requires jump labels to be initialized early. While x86, PowerPC, and
ARM64 arrange for jump_label_init() to be called before parse_args(),
ARM does not.
Kernel command line: rdinit=/sbin/init page_alloc.shuffle=1 panic=-1 console=ttyAMA0,115200 page_alloc.shuffle=1
------------[ cut here ]------------
WARNING: CPU: 0 PID: 0 at ./include/linux/jump_label.h:303
page_alloc_shuffle+0x12c/0x1ac
static_key_enable(): static key 'page_alloc_shuffle_key+0x0/0x4' used
before call to jump_label_init()
Modules linked in:
CPU: 0 PID: 0 Comm: swapper Not tainted
5.1.0-rc4-next-20190410-00003-g3367c36ce744 #1
Hardware name: ARM Integrator/CP (Device Tree)
[<c0011c68>] (unwind_backtrace) from [<c000ec48>] (show_stack+0x10/0x18)
[<c000ec48>] (show_stack) from [<c07e9710>] (dump_stack+0x18/0x24)
[<c07e9710>] (dump_stack) from [<c001bb1c>] (__warn+0xe0/0x108)
[<c001bb1c>] (__warn) from [<c001bb88>] (warn_slowpath_fmt+0x44/0x6c)
[<c001bb88>] (warn_slowpath_fmt) from [<c0b0c4a8>]
(page_alloc_shuffle+0x12c/0x1ac)
[<c0b0c4a8>] (page_alloc_shuffle) from [<c0b0c550>] (shuffle_store+0x28/0x48)
[<c0b0c550>] (shuffle_store) from [<c003e6a0>] (parse_args+0x1f4/0x350)
[<c003e6a0>] (parse_args) from [<c0ac3c00>] (start_kernel+0x1c0/0x488)
Move the fallback call to jump_label_init() to occur before
parse_args().
The redundant calls to jump_label_init() in other archs are left intact
in case they have static key toggling use cases that are even earlier
than option parsing.
Link: http://lkml.kernel.org/r/155544804466.1032396.13418949511615676665.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Reported-by: Guenter Roeck <groeck@google.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Mike Rapoport <rppt@linux.ibm.com>
Cc: Russell King <rmk@armlinux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Separate print_modules() and hard lockup error message.
Before the patch:
NMI watchdog: Watchdog detected hard LOCKUP on cpu 1Modules linked in: nls_cp437
Link: http://lkml.kernel.org/r/20190412062557.2700-1-sergey.senozhatsky@gmail.com
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The help text for CONFIG_ARCH_HAS_KCOV is stale, and describes the
feature as being enabled only for x86_64, when it is now enabled for
several architectures, including arm, arm64, powerpc, and s390.
Let's remove that stale help text, and update it along the lines of hat
for ARCH_HAS_FORTIFY_SOURCE, better describing when an architecture
should select CONFIG_ARCH_HAS_KCOV.
Link: http://lkml.kernel.org/r/20190412102733.5154-1-mark.rutland@arm.com
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Dmitry Vyukov <dvyukov@google.com>
Cc: Kees Cook <keescook@chromium.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
During !CONFIG_CGROUP reclaim, we expand the inactive list size if it's
thrashing on the node that is about to be reclaimed. But when cgroups
are enabled, we suddenly ignore the node scope and use the cgroup scope
only. The result is that pressure bleeds between NUMA nodes depending
on whether cgroups are merely compiled into Linux. This behavioral
difference is unexpected and undesirable.
When the refault adaptivity of the inactive list was first introduced,
there were no statistics at the lruvec level - the intersection of node
and memcg - so it was better than nothing.
But now that we have that infrastructure, use lruvec_page_state() to
make the list balancing decision always NUMA aware.
[hannes@cmpxchg.org: fix bisection hole]
Link: http://lkml.kernel.org/r/20190417155241.GB23013@cmpxchg.org
Link: http://lkml.kernel.org/r/20190412144438.2645-1-hannes@cmpxchg.org
Fixes: 2a2e48854d ("mm: vmscan: fix IO/refault regression in cache workingset transition")
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Reviewed-by: Shakeel Butt <shakeelb@google.com>
Cc: Roman Gushchin <guro@fb.com>
Cc: Michal Hocko <mhocko@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
has_unmovable_pages() is used by allocating CMA and gigantic pages as
well as the memory hotplug. The later doesn't know how to offline CMA
pool properly now, but if an unused (free) CMA page is encountered, then
has_unmovable_pages() happily considers it as a free memory and
propagates this up the call chain. Memory offlining code then frees the
page without a proper CMA tear down which leads to an accounting issues.
Moreover if the same memory range is onlined again then the memory never
gets back to the CMA pool.
State after memory offline:
# grep cma /proc/vmstat
nr_free_cma 205824
# cat /sys/kernel/debug/cma/cma-kvm_cma/count
209920
Also, kmemleak still think those memory address are reserved below but
have already been used by the buddy allocator after onlining. This
patch fixes the situation by treating CMA pageblocks as unmovable except
when has_unmovable_pages() is called as part of CMA allocation.
Offlined Pages 4096
kmemleak: Cannot insert 0xc000201f7d040008 into the object search tree (overlaps existing)
Call Trace:
dump_stack+0xb0/0xf4 (unreliable)
create_object+0x344/0x380
__kmalloc_node+0x3ec/0x860
kvmalloc_node+0x58/0x110
seq_read+0x41c/0x620
__vfs_read+0x3c/0x70
vfs_read+0xbc/0x1a0
ksys_read+0x7c/0x140
system_call+0x5c/0x70
kmemleak: Kernel memory leak detector disabled
kmemleak: Object 0xc000201cc8000000 (size 13757317120):
kmemleak: comm "swapper/0", pid 0, jiffies 4294937297
kmemleak: min_count = -1
kmemleak: count = 0
kmemleak: flags = 0x5
kmemleak: checksum = 0
kmemleak: backtrace:
cma_declare_contiguous+0x2a4/0x3b0
kvm_cma_reserve+0x11c/0x134
setup_arch+0x300/0x3f8
start_kernel+0x9c/0x6e8
start_here_common+0x1c/0x4b0
kmemleak: Automatic memory scanning thread ended
[cai@lca.pw: use is_migrate_cma_page() and update commit log]
Link: http://lkml.kernel.org/r/20190416170510.20048-1-cai@lca.pw
Link: http://lkml.kernel.org/r/20190413002623.8967-1-cai@lca.pw
Signed-off-by: Qian Cai <cai@lca.pw>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Reviewed-by: Oscar Salvador <osalvador@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 58bc4c34d2 ("mm/vmstat.c: skip NR_TLB_REMOTE_FLUSH* properly")
depends on skipping vmstat entries with empty name introduced in
7aaf772723 ("mm: don't show nr_indirectly_reclaimable in
/proc/vmstat") but reverted in b29940c1ab ("mm: rename and change
semantics of nr_indirectly_reclaimable_bytes").
So skipping no longer works and /proc/vmstat has misformatted lines " 0".
This patch simply shows debug counters "nr_tlb_remote_*" for UP.
Link: http://lkml.kernel.org/r/155481488468.467.4295519102880913454.stgit@buzz
Fixes: 58bc4c34d2 ("mm/vmstat.c: skip NR_TLB_REMOTE_FLUSH* properly")
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Roman Gushchin <guro@fb.com>
Cc: Jann Horn <jannh@google.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When adding memory by probing a memory block in the sysfs interface,
there is an obvious issue where we will unlock the device_hotplug_lock
when we failed to takes it.
That issue was introduced in 8df1d0e4a2 ("mm/memory_hotplug: make
add_memory() take the device_hotplug_lock").
We should drop out in time when failing to take the device_hotplug_lock.
Link: http://lkml.kernel.org/r/1554696437-9593-1-git-send-email-zhongjiang@huawei.com
Fixes: 8df1d0e4a2 ("mm/memory_hotplug: make add_memory() take the device_hotplug_lock")
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Reported-by: Yang yingliang <yangyingliang@huawei.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Oscar Salvador <osalvador@suse.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The igrab() in shmem_unuse() looks good, but we forgot that it gives no
protection against concurrent unmounting: a point made by Konstantin
Khlebnikov eight years ago, and then fixed in 2.6.39 by 778dd893ae
("tmpfs: fix race between umount and swapoff"). The current 5.1-rc
swapoff is liable to hit "VFS: Busy inodes after unmount of tmpfs.
Self-destruct in 5 seconds. Have a nice day..." followed by GPF.
Once again, give up on using igrab(); but don't go back to making such
heavy-handed use of shmem_swaplist_mutex as last time: that would spoil
the new design, and I expect could deadlock inside shmem_swapin_page().
Instead, shmem_unuse() just raise a "stop_eviction" count in the shmem-
specific inode, and shmem_evict_inode() wait for that to go down to 0.
Call it "stop_eviction" rather than "swapoff_busy" because it can be put
to use for others later (huge tmpfs patches expect to use it).
That simplifies shmem_unuse(), protecting it from both unlink and
unmount; and in practice lets it locate all the swap in its first try.
But do not rely on that: there's still a theoretical case, when
shmem_writepage() might have been preempted after its get_swap_page(),
before making the swap entry visible to swapoff.
[hughd@google.com: remove incorrect list_del()]
Link: http://lkml.kernel.org/r/alpine.LSU.2.11.1904091133570.1898@eggly.anvils
Link: http://lkml.kernel.org/r/alpine.LSU.2.11.1904081259400.1523@eggly.anvils
Fixes: b56a2d8af9 ("mm: rid swapoff of quadratic complexity")
Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: "Alex Xu (Hello71)" <alex_y_xu@yahoo.ca>
Cc: Huang Ying <ying.huang@intel.com>
Cc: Kelley Nielsen <kelleynnn@gmail.com>
Cc: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Cc: Rik van Riel <riel@surriel.com>
Cc: Vineeth Pillai <vpillai@digitalocean.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The old try_to_unuse() implementation was driven by find_next_to_unuse(),
which terminated as soon as all the swap had been freed.
Add inuse_pages checks now (alongside signal_pending()) to stop scanning
mms and swap_map once finished.
The same ought to be done in shmem_unuse() too, but never was before,
and needs a different interface: so leave it as is for now.
Link: http://lkml.kernel.org/r/alpine.LSU.2.11.1904081258200.1523@eggly.anvils
Fixes: b56a2d8af9 ("mm: rid swapoff of quadratic complexity")
Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: "Alex Xu (Hello71)" <alex_y_xu@yahoo.ca>
Cc: Huang Ying <ying.huang@intel.com>
Cc: Kelley Nielsen <kelleynnn@gmail.com>
Cc: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Cc: Rik van Riel <riel@surriel.com>
Cc: Vineeth Pillai <vpillai@digitalocean.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
SWAP_UNUSE_MAX_TRIES 3 appeared to work well in earlier testing, but
further testing has proved it to be a source of unnecessary swapoff
EBUSY failures (which can then be followed by unmount EBUSY failures).
When mmget_not_zero() or shmem's igrab() fails, there is an mm exiting
or inode being evicted, freeing up swap independent of try_to_unuse().
Those typically completed much sooner than the old quadratic swapoff,
but now it's more common that swapoff may need to wait for them.
It's possible to move those cases from init_mm.mmlist and shmem_swaplist
to separate "exiting" swaplists, and try_to_unuse() then wait for those
lists to be emptied; but we've not bothered with that in the past, and
don't want to risk missing some other forgotten case. So just revert to
cycling around until the swap is gone, without any retries limit.
Link: http://lkml.kernel.org/r/alpine.LSU.2.11.1904081256170.1523@eggly.anvils
Fixes: b56a2d8af9 ("mm: rid swapoff of quadratic complexity")
Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: "Alex Xu (Hello71)" <alex_y_xu@yahoo.ca>
Cc: Huang Ying <ying.huang@intel.com>
Cc: Kelley Nielsen <kelleynnn@gmail.com>
Cc: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Cc: Rik van Riel <riel@surriel.com>
Cc: Vineeth Pillai <vpillai@digitalocean.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Swapfile "type" was passed all the way down to shmem_unuse_inode(), but
then forgotten from shmem_find_swap_entries(): with the result that
removing one swapfile would try to free up all the swap from shmem - no
problem when only one swapfile anyway, but counter-productive when more,
causing swapoff to be unnecessarily OOM-killed when it should succeed.
Link: http://lkml.kernel.org/r/alpine.LSU.2.11.1904081254470.1523@eggly.anvils
Fixes: b56a2d8af9 ("mm: rid swapoff of quadratic complexity")
Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Cc: "Alex Xu (Hello71)" <alex_y_xu@yahoo.ca>
Cc: Vineeth Pillai <vpillai@digitalocean.com>
Cc: Kelley Nielsen <kelleynnn@gmail.com>
Cc: Rik van Riel <riel@surriel.com>
Cc: Huang Ying <ying.huang@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 51dedad06b ("kasan, slab: make freelist stored without tags")
calls kasan_reset_tag() for off-slab slab management object leading to
freelist being stored non-tagged.
However, cache_grow_begin() calls alloc_slabmgmt() which calls
kmem_cache_alloc_node() assigns a tag for the address and stores it in
the shadow address. As the result, it causes endless errors below
during boot due to drain_freelist() -> slab_destroy() ->
kasan_slab_free() which compares already untagged freelist against the
stored tag in the shadow address.
Since off-slab slab management object freelist is such a special case,
just store it tagged. Non-off-slab management object freelist is still
stored untagged which has not been assigned a tag and should not cause
any other troubles with this inconsistency.
BUG: KASAN: double-free or invalid-free in slab_destroy+0x84/0x88
Pointer tag: [ff], memory tag: [99]
CPU: 0 PID: 1376 Comm: kworker/0:4 Tainted: G W 5.1.0-rc3+ #8
Hardware name: HPE Apollo 70 /C01_APACHE_MB , BIOS L50_5.13_1.0.6 07/10/2018
Workqueue: cgroup_destroy css_killed_work_fn
Call trace:
print_address_description+0x74/0x2a4
kasan_report_invalid_free+0x80/0xc0
__kasan_slab_free+0x204/0x208
kasan_slab_free+0xc/0x18
kmem_cache_free+0xe4/0x254
slab_destroy+0x84/0x88
drain_freelist+0xd0/0x104
__kmem_cache_shrink+0x1ac/0x224
__kmemcg_cache_deactivate+0x1c/0x28
memcg_deactivate_kmem_caches+0xa0/0xe8
memcg_offline_kmem+0x8c/0x3d4
mem_cgroup_css_offline+0x24c/0x290
css_killed_work_fn+0x154/0x618
process_one_work+0x9cc/0x183c
worker_thread+0x9b0/0xe38
kthread+0x374/0x390
ret_from_fork+0x10/0x18
Allocated by task 1625:
__kasan_kmalloc+0x168/0x240
kasan_slab_alloc+0x18/0x20
kmem_cache_alloc_node+0x1f8/0x3a0
cache_grow_begin+0x4fc/0xa24
cache_alloc_refill+0x2f8/0x3e8
kmem_cache_alloc+0x1bc/0x3bc
sock_alloc_inode+0x58/0x334
alloc_inode+0xb8/0x164
new_inode_pseudo+0x20/0xec
sock_alloc+0x74/0x284
__sock_create+0xb0/0x58c
sock_create+0x98/0xb8
__sys_socket+0x60/0x138
__arm64_sys_socket+0xa4/0x110
el0_svc_handler+0x2c0/0x47c
el0_svc+0x8/0xc
Freed by task 1625:
__kasan_slab_free+0x114/0x208
kasan_slab_free+0xc/0x18
kfree+0x1a8/0x1e0
single_release+0x7c/0x9c
close_pdeo+0x13c/0x43c
proc_reg_release+0xec/0x108
__fput+0x2f8/0x784
____fput+0x1c/0x28
task_work_run+0xc0/0x1b0
do_notify_resume+0xb44/0x1278
work_pending+0x8/0x10
The buggy address belongs to the object at ffff809681b89e00
which belongs to the cache kmalloc-128 of size 128
The buggy address is located 0 bytes inside of
128-byte region [ffff809681b89e00, ffff809681b89e80)
The buggy address belongs to the page:
page:ffff7fe025a06e00 count:1 mapcount:0 mapping:01ff80082000fb00
index:0xffff809681b8fe04
flags: 0x17ffffffc000200(slab)
raw: 017ffffffc000200 ffff7fe025a06d08 ffff7fe022ef7b88 01ff80082000fb00
raw: ffff809681b8fe04 ffff809681b80000 00000001000000e0 0000000000000000
page dumped because: kasan: bad access detected
page allocated via order 0, migratetype Unmovable, gfp_mask
0x2420c0(__GFP_IO|__GFP_FS|__GFP_NOWARN|__GFP_COMP|__GFP_THISNODE)
prep_new_page+0x4e0/0x5e0
get_page_from_freelist+0x4ce8/0x50d4
__alloc_pages_nodemask+0x738/0x38b8
cache_grow_begin+0xd8/0xa24
____cache_alloc_node+0x14c/0x268
__kmalloc+0x1c8/0x3fc
ftrace_free_mem+0x408/0x1284
ftrace_free_init_mem+0x20/0x28
kernel_init+0x24/0x548
ret_from_fork+0x10/0x18
Memory state around the buggy address:
ffff809681b89c00: fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe
ffff809681b89d00: fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe
>ffff809681b89e00: 99 99 99 99 99 99 99 99 fe fe fe fe fe fe fe fe
^
ffff809681b89f00: 43 43 43 43 43 fe fe fe fe fe fe fe fe fe fe fe
ffff809681b8a000: 6d fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe
Link: http://lkml.kernel.org/r/20190403022858.97584-1-cai@lca.pw
Fixes: 51dedad06b ("kasan, slab: make freelist stored without tags")
Signed-off-by: Qian Cai <cai@lca.pw>
Reviewed-by: Andrey Konovalov <andreyknvl@google.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Avoid kretprobe recursion loop bg by setting a dummy
kprobes to current_kprobe per-CPU variable.
This bug has been introduced with the asm-coded trampoline
code, since previously it used another kprobe for hooking
the function return placeholder (which only has a nop) and
trampoline handler was called from that kprobe.
This revives the old lost kprobe again.
With this fix, we don't see deadlock anymore.
And you can see that all inner-called kretprobe are skipped.
event_1 235 0
event_2 19375 19612
The 1st column is recorded count and the 2nd is missed count.
Above shows (event_1 rec) + (event_2 rec) ~= (event_2 missed)
(some difference are here because the counter is racy)
Reported-by: Andrea Righi <righi.andrea@gmail.com>
Tested-by: Andrea Righi <righi.andrea@gmail.com>
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Fixes: c9becf58d9 ("[PATCH] kretprobe: kretprobe-booster")
Link: http://lkml.kernel.org/r/155094064889.6137.972160690963039.stgit@devbox
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Verify the stack frame pointer on kretprobe trampoline handler,
If the stack frame pointer does not match, it skips the wrong
entry and tries to find correct one.
This can happen if user puts the kretprobe on the function
which can be used in the path of ftrace user-function call.
Such functions should not be probed, so this adds a warning
message that reports which function should be blacklisted.
Tested-by: Andrea Righi <righi.andrea@gmail.com>
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/155094059185.6137.15527904013362842072.stgit@devbox
Signed-off-by: Ingo Molnar <mingo@kernel.org>
patch(1) doesn't set the x bit on files. So if someone downloads and
applies patch-4.21.xz, their kernel won't build. Fix that by executing
/bin/sh.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Cc: Boqun Feng <boqun.feng@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
err_spi is only called within SERIAL_SC16IS7XX_SPI
while err_i2c is called inside SERIAL_SC16IS7XX_I2C.
So we need to put err_spi and err_i2c into each #ifdef
accordingly.
This change fixes ("sc16is7xx: move label 'err_spi'
to correct section").
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Neil Armstrong