The patch extends the family of SATA-to-USB JMicron adapters that need
FUA to be disabled and applies the same policy for uas driver.
See details in http://unix.stackexchange.com/questions/237204/
Signed-off-by: Dmitry Katsubo <dmitry.katsubo@gmail.com>
Tested-by: Dmitry Katsubo <dmitry.katsubo@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sorry for the delay in this patch which was mostly caused by getting the
merger of the mpt2/mpt3sas driver, which was seen as an essential item of
maintenance work to do before the drivers diverge too much. Unfortunately,
this caused a compile failure (detected by linux-next), which then had to be
fixed up and incubated. In addition to the mpt2/3sas rework, there are
updates from pm80xx, lpfc, bnx2fc, hpsa, ipr, aacraid, megaraid_sas, storvsc
and ufs plus an assortment of changes including some year 2038 issues, a fix
for a remove before detach issue in some drivers and a couple of other minor
issues.
Signed-off-by: James Bottomley <JBottomley@Odin.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABAgAGBQJWRnpiAAoJEDeqqVYsXL0MJd0IAIkNP1q/6ksMw/lam2UlbdxN
zFsFOIhGM3xLnBFehbCx7JW3cmybA7WC5jhMjaa1OeJmYHLpwbTzvVwrLs2l/0y1
/S+G0wwxROZfIKj/1EO3oKbSPCu9N3lStxOnmNXt5PSUEzAXrTqSNTtnMf2ZGh7j
bQxTWEJe+66GckgGw4ozTXJHWXqM/Zs/FsYjn2h/WzFhFv8utr7zRSzHMVjcqpLG
TK/Lt03hiTGqiignKrV9W6JzdGTWf2LGIsj/njgR0dxv59cNH8PrHIjZyknSBxgn
lblinsCjxDHWnP4BSfTi9MQG1lEiZiWO3Y6TKkKJTgxZ9M0Eitspc+cLOiJ1mpg=
=HvQf
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull final round of SCSI updates from James Bottomley:
"Sorry for the delay in this patch which was mostly caused by getting
the merger of the mpt2/mpt3sas driver, which was seen as an essential
item of maintenance work to do before the drivers diverge too much.
Unfortunately, this caused a compile failure (detected by linux-next),
which then had to be fixed up and incubated.
In addition to the mpt2/3sas rework, there are updates from pm80xx,
lpfc, bnx2fc, hpsa, ipr, aacraid, megaraid_sas, storvsc and ufs plus
an assortment of changes including some year 2038 issues, a fix for a
remove before detach issue in some drivers and a couple of other minor
issues"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (141 commits)
mpt3sas: fix inline markers on non inline function declarations
sd: Clear PS bit before Mode Select.
ibmvscsi: set max_lun to 32
ibmvscsi: display default value for max_id, max_lun and max_channel.
mptfusion: don't allow negative bytes in kbuf_alloc_2_sgl()
scsi: pmcraid: replace struct timeval with ktime_get_real_seconds()
mvumi: 64bit value for seconds_since1970
be2iscsi: Fix bogus WARN_ON length check
scsi_scan: don't dump trace when scsi_prep_async_scan() is called twice
mpt3sas: Bump mpt3sas driver version to 09.102.00.00
mpt3sas: Single driver module which supports both SAS 2.0 & SAS 3.0 HBAs
mpt2sas, mpt3sas: Update the driver versions
mpt3sas: setpci reset kernel oops fix
mpt3sas: Added OEM Gen2 PnP ID branding names
mpt3sas: Refcount fw_events and fix unsafe list usage
mpt3sas: Refcount sas_device objects and fix unsafe list usage
mpt3sas: sysfs attribute to report Backup Rail Monitor Status
mpt3sas: Ported WarpDrive product SSS6200 support
mpt3sas: fix for driver fails EEH, recovery from injected pci bus error
mpt3sas: Manage MSI-X vectors according to HBA device type
...
This patch changes the !blk-mq path to the same defaults as the blk-mq
I/O path by always enabling block tagging, and always using host wide
tags. We've had blk-mq available for a few releases so bugs with
this mode should have been ironed out, and this ensures we get better
coverage of over tagging setup over different configs.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Jens Axboe <axboe@kernel.dk>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Previously, Coccinelle would issue the following false positive:
isd200.c:1478:14-18: ERROR: reference preceded by free on line 1472
This change rewrites the isd200_init_info function to have more explicit
execution pathways to make it easier for scripts and humans to parse.
Signed-off-by: Kris Borer <kborer@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-ESHUTDOWN means that the HC has been unplugged.
Reporting an error in that case makes no sense.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to Documentation/timers/timers-howto.txt"
udelay() is only called once from a place where sleeping is allowed.
We can replace it with a call to usleep_range()
with a reasonable upper limit.
Signed-off-by: Sunny Kumar <sunny.kumar.roy@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Grain-media GM12U320 based devices are mini video projectors using USB for
both power and video data transport.
Their usb-storage interface is a virtual windows driver CD.
The gm12u320 kms driver needs these interfaces to talk to the device and
export it as framebuffer & kms dri device nodes, so make sure that the
usb-storage driver does not bind to it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This device automatically switches itself to another mode (0x1405)
unless the specific access pattern of Windows is followed in its
initial mode. That makes a dirty unmount of the internal storage
devices inevitable if they are mounted. So the card reader of
such a device should be ignored, lest an unclean removal become
inevitable.
This replaces an earlier patch that ignored all LUNs of this device.
That patch was overly broad.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
CC: stable@vger.kernel.org
Reviewed-by: Lars Melin <larsm17@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here's the big USB patchset for 4.2-rc1. As is normal these days, the
majority of changes are in the gadget drivers, with a bunch of other
small driver changes.
All of these have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlWNobIACgkQMUfUDdst+ylXtQCgwTnzFBzly+3h1Npa2CWkr/Lw
TWAAn31qEP28MLjm8iVJLNPwdVd2kt1w
=hrdz
-----END PGP SIGNATURE-----
Merge tag 'usb-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB updates from Greg KH:
"Here's the big USB patchset for 4.2-rc1. As is normal these days, the
majority of changes are in the gadget drivers, with a bunch of other
small driver changes.
All of these have been in linux-next with no reported issues"
* tag 'usb-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (175 commits)
usb: dwc3: Use ASCII space in Kconfig
usb: chipidea: add work-around for Marvell HSIC PHY startup
usb: chipidea: allow multiple instances to use default ci_default_pdata
dt-bindings: Consolidate ChipIdea USB ci13xxx bindings
phy: add Marvell HSIC 28nm PHY
phy: Add Marvell USB 2.0 OTG 28nm PHY
dt-bindings: Add Marvell PXA1928 USB and HSIC PHY bindings
USB: ssb: use devm_kzalloc
USB: ssb: fix error handling in ssb_hcd_create_pdev()
usb: isp1760: check for null return from kzalloc
cdc-acm: Add support of ATOL FPrint fiscal printers
usb: chipidea: usbmisc_imx: Remove unneeded semicolon
USB: usbtmc: add device quirk for Rigol DS6104
USB: serial: mos7840: Use setup_timer
phy: twl4030-usb: add ABI documentation
phy: twl4030-usb: remove incorrect pm_runtime_get_sync() in probe function.
phy: twl4030-usb: remove pointless 'suspended' test in 'suspend' callback.
phy: twl4030-usb: make runtime pm more reliable.
drivers:usb:fsl: Fix compilation error for fsl ehci drv
usb: renesas_usbhs: Don't disable the pipe if Control write status stage
...
This is the usual grab bag of driver updates (lpfc, hpsa,
megaraid_sas, cxgbi, be2iscsi) plus an assortment of minor updates.
There are also one new driver: the Cisco snic; the advansys driver has
been rewritten to get rid of the warning about converting it to the
DMA API, the tape statistics patch got in and finally, there's a
resuffle of SCSI header files to separate more cleanly initiator from
target mode (and better share the common definitions).
Signed-off-by: James Bottomley <JBottomley@Odin.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABAgAGBQJViKWdAAoJEDeqqVYsXL0MAr8IAMmlA6HBVjMJJFCEOY9corHj
e70MNQa7LUgf+JCdOtzGcvHXTiFFd4IHZAwXUJAnsC4IU2QWEfi1bjUTErlqBIGk
LoZlXXpEHnFpmWot3OluOzzcGcxede8rVgPiKWVVdojIngBC2+LL/i2vPCJ84ri9
WCVlk6KBvWZXuU6JuOKAb2FO9HOX7Q61wuKAMast2Qc6RNc2ksgc7VbstsITqzZ9
FVEsjmQ5lqUj+xdxBpiUOdUpc22IJ4VcpBgQ2HrThvg6vf4aq937RJ/g4vi/g0SU
Utk0a3bUw1H/WnYAfJVFx83nVEsS/954Z7/ERDg1sjlfLYwQtQnpov0XIbPIbZU=
=k9IT
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is the usual grab bag of driver updates (lpfc, hpsa,
megaraid_sas, cxgbi, be2iscsi) plus an assortment of minor updates.
There is also one new driver: the Cisco snic. The advansys driver has
been rewritten to get rid of the warning about converting it to the
DMA API, the tape statistics patch got in and finally, there's a
resuffle of SCSI header files to separate more cleanly initiator from
target mode (and better share the common definitions)"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (156 commits)
snic: driver for Cisco SCSI HBA
qla2xxx: Fix indentation
qla2xxx: Comment out unreachable code
fusion: remove dead MTRR code
advansys: fix compilation errors and warnings when CONFIG_PCI is not set
mptsas: fix depth param in scsi_track_queue_full
megaraid: fix irq setup process regression
lpfc: Update version to 10.7.0.0 for upstream patch set.
lpfc: Fix to drop PLOGIs from fabric node till LOGO processing completes
lpfc: Fix scsi task management error message.
lpfc: Fix cq_id masking problem.
lpfc: Fix scsi prep dma buf error.
lpfc: Add support for using block multi-queue
lpfc: Devices are not discovered during takeaway/giveback testing
lpfc: Fix vport deletion failure.
lpfc: Check for active portpeerbeacon.
lpfc: Update driver version for upstream patch set 10.6.0.1.
lpfc: Change buffer pool empty message to miscellaneous category
lpfc: Fix incorrect log message reported for empty FCF record.
lpfc: Fix rport leak.
...
'0' is now used as the default cmd_per_lun value,
so there's no need to explicitly set it to '1' in the
host template.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
While accessing a unusual usb storage (ums-alauda, ums-cypress, ...),
the module reference count is not incremented. Because these drivers
allocate scsi hosts with usb_stor_host_template defined in usb-storage
module. So these drivers always can be unloaded.
This fixes it by preparing scsi host template which is initialized
at module_init() for each ums-* driver. In order to minimize the
difference in ums-* drivers, introduce module_usb_stor_driver() helper
macro which is same as module_usb_driver() except that it also
initializes scsi host template.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Vinayak Holikatti <vinholikatti@gmail.com>
Cc: Dolev Raviv <draviv@codeaurora.org>
Cc: Sujit Reddy Thumma <sthumma@codeaurora.org>
Cc: Subhash Jadavani <subhashj@codeaurora.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: "James E.J. Bottomley" <JBottomley@parallels.com>
Cc: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Hannes Reinecke <hare@suse.de>
Cc: linux-usb@vger.kernel.org
Cc: usb-storage@lists.one-eyed-alien.net
Cc: linux-scsi@vger.kernel.org
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Without this flag some versions of these enclosures do not work.
Cc: stable@vger.kernel.org
Reported-and-tested-by: Christian Schaller <cschalle@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Single transform macros with hidden arguments are not
particularly useful. Just use seq_printf directly instead.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Testing has shown that ASM1053 devices do not work properly with transfers
larger than 240 sectors, so set max_sectors to 240 on these.
Cc: stable@vger.kernel.org # 3.16
Reported-by: Steve Bangert <sbangert@frontier.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Steve Bangert <sbangert@frontier.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The usb-storage driver sets max_sectors = 240 in its scsi-host template,
for uas we do not want to do that for all devices, but testing has shown
that some devices need it.
This commit adds a US_FL_MAX_SECTORS_240 flag for such devices, and
implements support for it in uas.c, while at it it also adds support
for US_FL_MAX_SECTORS_64 to uas.c.
Cc: stable@vger.kernel.org # 3.16
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
uas_use_uas_driver may set some US_FL_foo flags during detection, currently
these are stored in a local variable and then throw away, but these may be
of interest to the caller, so add an extra parameter to (optionally) return
the detected flags, and use this in the uas driver.
Cc: stable@vger.kernel.org # 3.16
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes errors thrown by checkpatch over a space issue and the
incorrect indentation of a switch statement.
Signed-off-by: Bas Peters <baspeters93@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch places braces on a new line following function declarations.
Signed-off-by: Bas Peters <baspeters93@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A new uas compatible controller has shown up in some people's devices from
the manufacturer Initio Corporation, this controller needs the US_FL_NO_ATA_1X
quirk to work properly with uas, so add it to the uas quirks table.
Reported-and-tested-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Cc: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Cc: stable@vger.kernel.org # 3.16
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is necessary to make some storage arrays work.
Some storage devices have more than 8 LUNs. In addition
you can hook up a WideSCSI bus to USB. In these cases even
level 2 devices can have more than 8 LUNs. For them
it is necessary to simply believe the class specific
command and report its result back to the SCSI layer.
Off by one Alan noticed is fixed.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Like the JMicron JMS567 enclosures with the JMS539 choke on report-opcodes,
so avoid it.
Tested-and-reported-by: Tom Arild Naess <tanaess@gmail.com>
Cc: stable@vger.kernel.org # 3.16
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Like some other uas devices these devices hang when a report-opcodes scsi
command is send to them.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1124119
Cc: stable@vger.kernel.org # 3.16
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I recently posted a patch ("storage: Add quirk for another SCM-based
USB-SCSI converter") to add a quirk for the converter with ID 04E6:000F,
which is listed along with 04E6:000B in the Windows INF file for the
Startech ICUSBSCSI2 as "eUSB SCSI Adapter (Bus Powered)".
The already-present quirk for 04E6:000B has USB_SC_SCSI/USB_PR_BULK, not
USB_SC_DEVICE/USB_PR_DEVICE. Change the 04E6:000F quirk to match that,
since it will probably be required.
Signed-off-by: Mark Knibbs <markk@clara.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Just like all previous UAS capable Seagate disk enclosures, these need the
US_FL_NO_ATA_1X to not crash when udev probes them.
Cc: stable@vger.kernel.org # 3.16
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Our detection logic to avoid doing UAS on ASM1051 bridge chips causes problems
with newer ASM1153 disk enclosures in 2 ways:
1) Some ASM1153 disk enclosures re-use the ASM1051 device-id of 5106, which
we assume is always an ASM1051, so remove the quirk for 5106, and instead
use the same detection logic as we already use for device-id 55aa, which is
used for all of ASM1051, ASM1053 and ASM1153 devices <sigh>.
2) Our detection logic to differentiate between ASM1051 and ASM1053 sees
ASM1153 devices as ASM1051 because they have 32 streams like ASM1051 devs.
Luckily the ASM1153 descriptors are not 100% identical, unlike the previous
models the ASM1153 has bMaxPower == 0, so use that to differentiate it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Apricorn SATA dongle will occasionally return "USBSUSBSUSB" in
response to SCSI commands when running in UAS mode. Therefore,
disable UAS mode on this dongle.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Like the JMicron JMS567 enclosures with the JMS566 choke on report-opcodes,
so avoid it.
Tested-and-reported-by: Takeo Nakayama <javhera@gmx.com>
Cc: stable@vger.kernel.org # 3.16
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is yet another Seagate device which needs the US_FL_NO_ATA_1X quirk
Reported-by: Marcin Zajączkowski <mszpak@wp.pl>
Cc: stable@vger.kernel.org # 3.16
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Fix a regression in leds-gpio introduced by a recent commit that
inadvertently changed the name of one of the properties used by
the driver (Fabio Estevam).
- Fix a regression in the ACPI backlight driver introduced by a
recent fix that missed one special case that had to be taken
into account (Aaron Lu).
- Drop the level of some new kernel messages from the ACPI core
introduced by a recent commit to KERN_DEBUG which they should
have used from the start and drop some other unuseful KERN_ERR
messages printed by ACPI (Rafael J Wysocki).
- Revert an incorrect commit modifying the cpupower tool
(Prarit Bhargava).
- Fix two regressions introduced by recent commits in the OPP
library and clean up some existing minor issues in that code
(Viresh Kumar).
- Continue to replace CONFIG_PM_RUNTIME with CONFIG_PM throughout
the tree (or drop it where that can be done) in order to make
it possible to eliminate CONFIG_PM_RUNTIME (Rafael J Wysocki,
Ulf Hansson, Ludovic Desroches). There will be one more
"CONFIG_PM_RUNTIME removal" batch after this one, because some
new uses of it have been introduced during the current merge
window, but that should be sufficient to finally get rid of it.
- Make the ACPI EC driver more robust against race conditions
related to GPE handler installation failures (Lv Zheng).
- Prevent the ACPI device PM core code from attempting to
disable GPEs that it has not enabled which confuses ACPICA
and makes it report errors unnecessarily (Rafael J Wysocki).
- Add a "force" command line switch to the intel_pstate driver
to make it possible to override the blacklisting of some
systems in that driver if needed (Ethan Zhao).
- Improve intel_pstate code documentation and add a MAINTAINERS
entry for it (Kristen Carlson Accardi).
- Make the ACPI fan driver create cooling device interfaces
witn names that reflect the IDs of the ACPI device objects
they are associated with, except for "generic" ACPI fans
(PNP ID "PNP0C0B"). That's necessary for user space thermal
management tools to be able to connect the fans with the
parts of the system they are supposed to be cooling properly.
From Srinivas Pandruvada.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=5fo2
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.19-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI and power management updates from Rafael Wysocki:
"These are regression fixes (leds-gpio, ACPI backlight driver,
operating performance points library, ACPI device enumeration
messages, cpupower tool), other bug fixes (ACPI EC driver, ACPI device
PM), some cleanups in the operating performance points (OPP)
framework, continuation of CONFIG_PM_RUNTIME elimination, a couple of
minor intel_pstate driver changes, a new MAINTAINERS entry for it and
an ACPI fan driver change needed for better support of thermal
management in user space.
Specifics:
- Fix a regression in leds-gpio introduced by a recent commit that
inadvertently changed the name of one of the properties used by the
driver (Fabio Estevam).
- Fix a regression in the ACPI backlight driver introduced by a
recent fix that missed one special case that had to be taken into
account (Aaron Lu).
- Drop the level of some new kernel messages from the ACPI core
introduced by a recent commit to KERN_DEBUG which they should have
used from the start and drop some other unuseful KERN_ERR messages
printed by ACPI (Rafael J Wysocki).
- Revert an incorrect commit modifying the cpupower tool (Prarit
Bhargava).
- Fix two regressions introduced by recent commits in the OPP library
and clean up some existing minor issues in that code (Viresh
Kumar).
- Continue to replace CONFIG_PM_RUNTIME with CONFIG_PM throughout the
tree (or drop it where that can be done) in order to make it
possible to eliminate CONFIG_PM_RUNTIME (Rafael J Wysocki, Ulf
Hansson, Ludovic Desroches).
There will be one more "CONFIG_PM_RUNTIME removal" batch after this
one, because some new uses of it have been introduced during the
current merge window, but that should be sufficient to finally get
rid of it.
- Make the ACPI EC driver more robust against race conditions related
to GPE handler installation failures (Lv Zheng).
- Prevent the ACPI device PM core code from attempting to disable
GPEs that it has not enabled which confuses ACPICA and makes it
report errors unnecessarily (Rafael J Wysocki).
- Add a "force" command line switch to the intel_pstate driver to
make it possible to override the blacklisting of some systems in
that driver if needed (Ethan Zhao).
- Improve intel_pstate code documentation and add a MAINTAINERS entry
for it (Kristen Carlson Accardi).
- Make the ACPI fan driver create cooling device interfaces witn
names that reflect the IDs of the ACPI device objects they are
associated with, except for "generic" ACPI fans (PNP ID "PNP0C0B").
That's necessary for user space thermal management tools to be able
to connect the fans with the parts of the system they are supposed
to be cooling properly. From Srinivas Pandruvada"
* tag 'pm+acpi-3.19-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (32 commits)
MAINTAINERS: add entry for intel_pstate
ACPI / video: update the skip case for acpi_video_device_in_dod()
power / PM: Eliminate CONFIG_PM_RUNTIME
NFC / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
SCSI / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
ACPI / EC: Fix unexpected ec_remove_handlers() invocations
Revert "tools: cpupower: fix return checks for sysfs_get_idlestate_count()"
tracing / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
x86 / PM: Replace CONFIG_PM_RUNTIME in io_apic.c
PM: Remove the SET_PM_RUNTIME_PM_OPS() macro
mmc: atmel-mci: use SET_RUNTIME_PM_OPS() macro
PM / Kconfig: Replace PM_RUNTIME with PM in dependencies
ARM / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
sound / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
phy / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
video / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
tty / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
spi: Replace CONFIG_PM_RUNTIME with CONFIG_PM
ACPI / PM: Do not disable wakeup GPEs that have not been enabled
ACPI / utils: Drop error messages from acpi_evaluate_reference()
...
Here's the big set of USB and PHY patches for 3.19-rc1.
The normal churn in the USB gadget area is in here, as well as xhci and
other individual USB driver updates. The PHY tree is also in here, as
there were dependancies on the USB tree.
All of these have been in linux-next.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOEHcACgkQMUfUDdst+ykziQCgsm1D/af2nac6CTF2pov8VMIY
ywgAnRi8LtZ2WassrwTNxY86Avaqryis
=UVp8
-----END PGP SIGNATURE-----
Merge tag 'usb-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB updates from Greg KH:
"Here's the big set of USB and PHY patches for 3.19-rc1.
The normal churn in the USB gadget area is in here, as well as xhci
and other individual USB driver updates. The PHY tree is also in
here, as there were dependancies on the USB tree.
All of these have been in linux-next"
* tag 'usb-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (351 commits)
arm: omap3: twl: remove usb phy init data
usbip: fix error handling in stub_probe()
usb: gadget: udc: missing curly braces
USB: mos7720: delete some unneeded code
wusb: replace memset by memzero_explicit
usbip: remove unneeded structure
usb: xhci: fix comment for PORT_DEV_REMOVE
xhci: don't use the same variable for stopped and halted rings current TD
xhci: clear extra bits from slot context when setting max exit latency
xhci: cleanup finish_td function
USB: adutux: NULL dereferences on disconnect
usb: chipidea: fix platform_no_drv_owner.cocci warnings
usb: chipidea: Fixed a few typos in comments
Documentation: bindings: add doc for the USB2 ChipIdea USB driver
usb: chipidea: add a usb2 driver for ci13xxx
usb: chipidea: fix phy handling
usb: chipidea: remove duplicate dev_set_drvdata for host_start
usb: chipidea: parameter 'mode' isn't needed for hw_device_reset
usb: chipidea: add controller reset API
usb: chipidea: remove flag CI_HDRC_REQUIRE_TRANSCEIVER
...
After commit b2b49ccbdd (PM: Kconfig: Set PM_RUNTIME if PM_SLEEP is
selected) PM_RUNTIME is always set if PM is set, so Kconfig options
depending on CONFIG_PM_RUNTIME may now be changed to depend on
CONFIG_PM.
Replace PM_RUNTIME with PM in Kconfig dependencies throughout the
tree.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Tejun Heo <tj@kernel.org>
Conflicts:
drivers/scsi/scsi_debug.c
Agreed and tested resolution to a merge problem between a fix in scsi_debug
and a driver update
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch does two things for SCM eUSCSI USB-SCSI converters:
1. SCM eUSCSI bridge devices are hard-wired to use SCSI ID 7. On connecting
the converter, access to that ID is attempted during the bus scan. Asking
the converter to issue INQUIRY commands to itself isn't very polite and
wastes time. Set this_id to 7 so __scsi_scan_target() skips it in the scan.
2. Enable multi-LUN support. eUSCSI devices don't support Get Max LUN
requests, returning an error (-32). [Different targets could have different
numbers of LUNs, so it wouldn't make sense to return a particular value in
response to Get Max LUN.]
usb_stor_scan_dwork() does this:
/* For bulk-only devices, determine the max LUN value */
if (us->protocol == USB_PR_BULK && !(us->fflags & US_FL_SINGLE_LUN)) {
mutex_lock(&us->dev_mutex);
us->max_lun = usb_stor_Bulk_max_lun(us);
mutex_unlock(&us->dev_mutex);
It avoids calling usb_stor_Bulk_max_lun() if US_FL_SINGLE_LUN, but not for
US_FL_SCM_MULT_TARG. Since usb_stor_Bulk_max_lun() returns 0 in the error
case, us->max_lun was always set to 0.
[If the user doesn't want multi-LUN support (perhaps there are SCSI devices
which respond to commands on all LUNs?), the US_FL_SINGLE_LUN quirk can be
specified on the kernel command line.]
Signed-off-by: Mark Knibbs <markk@clara.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb_stor_euscsi_init() enables multi-target mode for SCM eUSB SCSI bridge
devices. The control message it sends has wLength = 1 and the byte sent is
0x01. While that works, the SCM Windows driver does it with wLength = 0. We
may as well match what the SCM driver does.
Signed-off-by: Mark Knibbs <markk@clara.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drop the now unused reason argument from the ->change_queue_depth method.
Also add a return value to scsi_adjust_queue_depth, and rename it to
scsi_change_queue_depth now that it can be used as the default
->change_queue_depth implementation.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Hannes Reinecke <hare@suse.de>
These disks have a broken uas implementation, the tag field of the status
iu-s is not set properly, so we need to fall-back to usb-storage for these.
Cc: stable@vger.kernel.org # 3.16
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the tagged argument from scsi_adjust_queue_depth, and just let it
handle the queue depth. For most drivers those two are fairly separate,
given that most modern drivers don't care about the SCSI "tagged" status
of a command at all, and many old drivers allow queuing of multiple
untagged commands in the driver.
Instead we start out with the ->simple_tags flag set before calling
->slave_configure, which is how all drivers actually looking at
->simple_tags except for one worke anyway. The one other case looks
broken, but I've kept the behavior as-is for now.
Except for that we only change ->simple_tags from the ->change_queue_type,
and when rejecting a tag message in a single driver, so keeping this
churn out of scsi_adjust_queue_depth is a clear win.
Now that the usage of scsi_adjust_queue_depth is more obvious we can
also remove all the trivial instances in ->slave_alloc or ->slave_configure
that just set it to the cmd_per_lun default.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Allow a driver to ask for block layer tags by setting .use_blk_tags in the
host template, in which case it will always see a valid value in
request->tag, similar to the behavior when using blk-mq. This means even
SCSI "untagged" commands will now have a tag, which is especially useful
when using a host-wide tag map.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Currently scsi piggy backs on the block layer to define the concept
of a tagged command. But we want to be able to have block-level host-wide
tags assigned even for untagged commands like the initial INQUIRY, so add
a new SCSI-level flag for commands that are tagged at the scsi level, so
that even commands without that set can have tags assigned to them. Note
that this alredy is the case for the blk-mq code path, and this just lets
the old path catch up with it.
We also set this flag based upon sdev->simple_tags instead of the block
queue flag, so that it is entirely independent of the block layer tagging,
and thus always correct even if a driver doesn't use block level tagging
yet.
Also remove the old blk_rq_tagged; it was only used by SCSI drivers, and
removing it forces them to look for the proper replacement.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
We should be using the standard dev_printk() variants for
sense code printing.
[hch: remove __scsi_print_sense call in xen-scsiback, Acked by Juergen]
[hch: folded bracing fix from Dan Carpenter]
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Robert Elliott <elliott@hp.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Some mass storage devices return a bogus value in response to a Get Max LUN
request. The Iomega Jaz USB Adapter responds with 0x10, hence my recent
patch to use the US_FL_SINGLE_LUN quirk for it.
The USB MSC Bulk Only Transport document says "The device shall return one
byte of data that contains the maximum LUN supported by the device."
Since the LUN field in the command block wrapper is only 4 bits wide, it
might be helpful to report too-large LUN values in the kernel log, and
assume max LUN is actually 0. That could get some devices which currently
need the US_FL_SINGLE_LUN quirk to work.
Signed-off-by: Mark Knibbs <markk@clara.co.uk>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The timeout argument to usb_stor_control_msg() is specified in jiffies, not
milliseconds.
Signed-off-by: Mark Knibbs <markk@clara.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit bda9893c50 as it was
incorrect.
Reported-by: Mark Knibbs <markk@clara.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These drives hang when receiving ATA12 commands, so set the US_FL_NO_ATA_1X
quirk to filter these out.
Cc: stable@vger.kernel.org # 3.16
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No caller or macro uses the return value so make it void.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With uas over usb-3 the tags inside the uas iu-s must match the usb-3 stream
ids, and those go from 1 - qdepth.
Before blk-mq calling scsi_activate_tcq(sdev, qdepth) guaranteed that we would
only get cmnd->request->tag from 0 - (qdepth - 1), and we used those as
uas-tags / stream-ids.
With blk-mq however we are guaranteed to never get more then qdepth commands
queued at the same time, but the cmnd->request->tag values may be much larger,
which breaks uas.
This commit fixes this by generating uas tags in the 1 - qdepth range ourselves
instead of using cmnd->request->tag.
While touching all involved code anyways also rename the uas_cmd_info stream
field to uas_tag, because when using uas over usb-2 streams are not used.
Cc: Christoph Hellwig <hch@infradead.org>
Reported-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
--
Changes in v2:
-Remove ".disable_blk_mq = true" from uas_host_template
Changes in v3:
-Rebased on top of Linus' current master branch
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Functions fw5895_init() and config_autodelink_before_power_down() are used
only when CONFIG_PM is defined.
drivers/usb/storage/realtek_cr.c:699:13: warning: 'fw5895_init' defined but not used [-Wunused-function]
drivers/usb/storage/realtek_cr.c:629:12: warning: 'config_autodelink_before_power_down' defined but not used [-Wunused-function]
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Just like some Seagate enclosures, these devices do not seem to grok ata
pass through commands.
Cc: stable@vger.kernel.org # 3.16
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These drives hang when receiving ATA12 commands, so set the US_FL_NO_ATA_1X
quirk to filter these out.
Cc: stable@vger.kernel.org # 3.16
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sometimes mass-storage devices using the Bulk-only transport will
mistakenly skip the data phase of a command. Rather than sending the
data expected by the host or sending a zero-length packet, they go
directly to the status phase and send the CSW.
This causes problems for usb-storage, for obvious reasons. The driver
will interpret the CSW as a short data transfer and will wait to
receive a CSW. The device won't have anything left to send, so the
command eventually times out.
The SCSI layer doesn't retry commands after they time out (this is a
relatively recent change). Therefore we should do our best to detect
a skipped data phase and handle it promptly.
This patch adds code to do that. If usb-storage receives a short
13-byte data transfer from the device, and if the first four bytes of
the data match the CSW signature, the driver will set the residue to
the full transfer length and interpret the data as a CSW.
This fixes Bugzilla #86611.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Tested-by: Paul Osmialowski <newchief@king.net.pl>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here's the big USB patchset for 3.18-rc1. Also in here is the PHY tree,
as it seems to fit well with the USB tree for various reasons...
Anyway, lots of little changes in here, all over the place, full details
in the changelog below.
All have been in the linux-next tree for a while with no issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlQ0aLYACgkQMUfUDdst+ylBvwCgs9fGRj0RQkLyGhQdEpzdZtTU
ZcwAoMPBImnaA1ZeSl7ZnoO8vC/WE4bR
=tfpj
-----END PGP SIGNATURE-----
Merge tag 'usb-3.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB updates from Greg KH:
"Here's the big USB patchset for 3.18-rc1. Also in here is the PHY
tree, as it seems to fit well with the USB tree for various reasons...
Anyway, lots of little changes in here, all over the place, full
details in the changelog
All have been in the linux-next tree for a while with no issues"
* tag 'usb-3.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (244 commits)
USB: host: st: fix typo 'CONFIG_USB_EHCI_HCD_ST'
uas: Reduce number of function arguments for uas_alloc_foo functions
xhci: Allow xHCI drivers to be built as separate modules
xhci: Export symbols used by host-controller drivers
xhci: Check for XHCI_COMP_MODE_QUIRK when disabling D3cold
xhci: Introduce xhci_init_driver()
usb: hcd: add generic PHY support
usb: rename phy to usb_phy in HCD
usb: gadget: uvc: fix up uvcg_v4l2_get_unmapped_area typo
USB: host: st: fix ehci/ohci driver selection
usb: host: ehci-exynos: Remove unnecessary usb-phy support
usb: core: return -ENOTSUPP for all targeted hosts
USB: Remove .owner field for driver
usb: core: log higher level message on malformed LANGID descriptor
usb: Add LED triggers for USB activity
usb: Rename usb-common.c
usb: gadget: Refactor request completion
usb: gadget: Introduce usb_gadget_giveback_request()
usb: dwc2/gadget: move phy bus legth initialization
phy: remove .owner field for drivers using module_platform_driver
...
This patch set consists of the usual driver updates (megaraid_sas, arcmsr,
be2iscsi, lpfc, mpt2sas, mpt3sas, qla2xxx, ufs) plus several assorted fixes
and miscellaneous updates (including the pci_msix_enable_range() changes that
have been pending for a while).
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJUNHvtAAoJEDeqqVYsXL0MzaoIAJ/R2JW/Xm50rD6iUj6RfjEc
6OOi3sOJe6yivPFLLTmIZyLcgHuZKPVXsjcjBXENsrjJeyu2aTq+vs2bOJN9BRYU
gHGyAEhVPKsvecYhEj/78ClRIMzwkr7KQMQConbClDa0sVr62M/dPQVHNvjaTDeS
rtmPGZbNpv9rCl0itNBLMrnOBT/MduuWtS2VNCAkV5yFU8kvEax5pizB+W4ztjoe
BnVnF8OJC70wAM4vpiUcgwCR5AGmYv5SQKn3AHNBayrJic0MLUSIhrnCptc9TSir
zWJAyoW2iQY1LKmihjwjDlXP40jbfOaBacEycqTUKNkfMRKbBl3qQa4IUrR1XsQ=
=I1Yg
-----END PGP SIGNATURE-----
Merge tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This patch set consists of the usual driver updates (megaraid_sas,
arcmsr, be2iscsi, lpfc, mpt2sas, mpt3sas, qla2xxx, ufs) plus several
assorted fixes and miscellaneous updates (including the
pci_msix_enable_range() changes that have been pending for a while)"
* tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (202 commits)
scsi: add a CONFIG_SCSI_MQ_DEFAULT option
ufs: definitions for phy interface
ufs: tune bkops while power managment events
ufs: Add support for clock scaling using devfreq framework
ufs: Add freq-table-hz property for UFS device
ufs: Add support for clock gating
ufs: refactor configuring power mode
ufs: add UFS power management support
ufs: introduce well known logical unit in ufs
ufs: manually add well known logical units
ufs: Active Power Mode - configuring bActiveICCLevel
ufs: improve init sequence
ufs: refactor query descriptor API support
ufs: add voting support for host controller power
ufs: Add clock initialization support
ufs: Add regulator enable support
ufs: Allow vendor specific initialization
scsi: don't add scsi_device if its already visible
scsi: fix the type for well known LUs
scsi: fix comment in struct Scsi_Host definition
...
This is a set of two small fixes, both to code which went in during the merge
window: cxgb4i has a scheduling in atomic bug in its new ipv6 code and uas
fails to work properly with the new scsi-mq code.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJUMMu/AAoJEDeqqVYsXL0MRlQH/1qE/e5xRfpftgTtjpqC0BFa
7M4X48YRCxuKi/QJ3oOMpdj30ExXZ8sKfHsQiXBDlgyJzjE2sfsz70Z/mnm7kfxv
y0c9+C4y4AJ9b3Qn67Zk7l/elpZdzYfk2WFZsJ+AvC/bBXUTff7G1I2wnC36gdS4
S3+ZlCmbNlR1CNNm6xrqEKgGRIuQxonI5foJj6ovz/OvHiFQfpYTm0IvZNNCXYD3
rLg1661WA9BJP/r+B5uTwCmlNxJereiLJJwPR39OxWYXwgsvHVNYP/ae7NNFPl3R
zT1oeoaLoZn0r6lZKFmH3W4Sa2C7tZ0aWROCtU6O/EhUUQCXJPJfOYgwNPGVUaE=
=RzIY
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is a set of two small fixes, both to code which went in during
the merge window: cxgb4i has a scheduling in atomic bug in its new
ipv6 code and uas fails to work properly with the new scsi-mq code"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
[SCSI] uas: disable use of blk-mq I/O path
[SCSI] cxgb4i: avoid holding mutex in interrupt context
The stream_id and pipe are already present in uas_cmd_info resp uas_dev_info,
so there is no need to pass a copy along.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The uas driver uses the block layer tag for USB3 stream IDs. With
blk-mq we can get larger tag numbers that the queue depth, which breaks
this assumption. A fix is under way for 3.18, but sits on top of
large changes so can't easily be backported. Set the disable_blk_mq
path so that a uas device can't easily crash the system when using
blk-mq for SCSI.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
There is apparently another SCM USB-SCSI converter with ID 04E6:000F. It
is listed along with 04E6:000B in the Windows INF file for the Startech
ICUSBSCSI2 as "eUSB SCSI Adapter (Bus Powered)". The quirk allows
devices with SCSI ID other than 0 to be accessed.
Also make a couple of existing SCM product IDs lower case to be
consistent with other entries.
Signed-off-by: Mark Knibbs <markk@clara.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Castlewood Systems supplied various models of USB-SCSI converter with their
ORB external removable-media drive. The ORB Windows and Macintosh drivers
support six USB IDs:
084B:A001 [VID 084B is Castlewood Systems]
04E6:0002 (*) ORB USB Smart Cable P/N 88205-001 (generic SCM ID)
2027:A001 Double-H Technology DH-2000SC
1822:0001 (*) Ariston iConnect/iSCSI
07AF:0004 (*) Microtech XpressSCSI (25-pin)
07AF:0005 (*) Microtech XpressSCSI (50-pin)
*: quirk already in unusual-devs.h
[Apparently the official VID for Double-H Technology is 0x07EB = 2027
decimal. That's another hex/decimal mix-up with these SCM-based products
(in addition to the Ariston and Entrega ones). Perhaps the USB-IF informed
companies of their allocated VID in decimal, but they assumed it was hex?
It seems all Entrega products used VID 0x1645, not just the USB-SCSI
converter.]
Double-H Technology Co., Ltd. produced a USB-SCSI converter, model
DH-2000SC, which is probably the one supported by the ORB drivers. Perhaps
the Castlewood-bundled product had a different label or PID though?
Castlewood mentioned Conmate as being one type of USB-SCSI converter.
Conmate and Double-H seem related somehow; both company addresses in the
same road, and at one point the Conmate web site mentioned DH-2000H4,
DH-200D4/DH-2000C4 as models of USB hub (DH short for Double-H presumably).
Conmate did show a USB-SCSI converter model CM-660 on their web site at one
point. My guess is that was identical to the DH-2000SC.
Mention of the Double-H product:
http://web.archive.org/web/20010221010141/http://www.doubleh.com.tw/dh-2000sc.htm
The only picture I could find is at
http://jp.acesuppliers.com/catalog/j64/component/page03.html
The casing design looks the same as my ORB USB Smart Cable which has ID
04E6:0002.
Anyway, that's enough rambling. Here's the patch.
storage: Add quirks for Castlewood and Double-H USB-SCSI converters
Add quirks for two SCM-based USB-SCSI converters which were bundled with
some Castlewood ORB removable drives. Without the quirk only the (single)
drive with SCSI ID 0 can be accessed.
Signed-off-by: Mark Knibbs <markk@clara.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb_stor_euscsi_init() calls usb_stor_control_msg() with timeout
argument 5000. USB_CTRL_SET_TIMEOUT is defined to be 5000 in usb.h, so
would it make sense to use that instead? Patch below if it would.
Signed-off-by: Mark Knibbs <markk@clara.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixed typos in comments of various drivers/usb files
Signed-off-by: Mickael Maison <mickael.maison@gmail.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of dereference each byte let's use %*ph specifier in the printk()
calls.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If something goes wrong in our communication with an uas device we may get
a response iu in reaction to a cmnd, rather then a status iu. In this case
propagate an error upwards, rather then logging a bogus iu message.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of doing:
uas_log_cmd_state(cmnd, __func__)
scmd_printk(KERN_ERR, cmnd, "error doing foo %d\n", err)
On error, resulting in 2 log calls for a single error, make uas_log_cmd_state
take a status code, and change calls like the above to:
uas_log_cmd_state(cmnd, "error doing foo", err)
Also change various sanity checks (which should never trigger) from:
"scmd_printk(KERN_ERR, cmnd, "sanity foo failed\n")" to calling the new
uas_log_cmd_state(), so that when they do trigger we get more info.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We've removed all hack from the driver for pre-production hardware.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I've access to a number of different uas devices now, and none of them use
old style sense urbs. The only case where these code-paths trigger is with
the asm1051 and there they do the wrong thing, as the asm1051 sends 8 bytes
status iu-s when it does not have any sense data, but uses new style
sense iu-s regardless, as can be seen for scsi cmnds where there is sense
data.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It was only used to sanity check against completing the same cmnd twice,
but that is the case we're likely operating on free-ed memory, and doing
sanity checks on free-ed memory is not really helpful.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use scsi_print_command to print commands during errors, rather then printing
the rather meaningless pointer to the command.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Check for both type of cancellation codes for sense and data urbs.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Limit the no-streams case to speeds less then USB_SPEED_SUPER.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The purpose of uas_pre_reset is to:
1) Stop any new commands from being submitted while an externally triggered
usb-device-reset is running
2) Wait for any pending commands to finish before allowing the usb-device-reset
to continue
The purpose of uas_suspend is to:
2) Wait for any pending commands to finish before suspending
This commit fixes races in both paths:
1) For 1) we use scsi_block_requests, but the scsi midlayer calls queuecommand
without holding any locks, so a queuecommand may already past the midlayer
scsi_block_requests checks when we call it, add a check to uas_queuecommand
to fix this
2) For 2) we were waiting for all sense-urbs to complete, there are 2 problems
with this approach:
a) data-urbs may complete after the sense urb, so we need to check for those
too
b) if a sense-urb completes with a iu id of READ/WRITE_READY a command is not
yet done. We submit a new sense-urb immediately in this case, but that
submit may fail (in which case it will get retried by uas_do_work), if this
happens the sense_urbs anchor may become empty while the cmnd is not yet
done
Also unblock requests on timeout, to avoid things getting stuck in that case.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Not all urbs we've allocated are necessarily also submitted, non-submitted
urbs will not be free-ed by their completion handler. So we need to free
them manually.
There are 2 scenarios where this can happen:
1) We have failed to submit some urbs at abort / disconnect
2) When running over usb-2 we may have never tried to submit the data urbs
when completing the scsi cmnd, because we never got a READ/WRITE_READY iu
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Do not keep references around to a cmnd which is under error handling.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is not strictly necessary for the cmd urb to have a reference to the
cmnd, and without this reference it becomes easier to drop all references to
a cmnd on an abort.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We've the same info doubled in both the inflight list and the cmnd array,
drop the list.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The data urbs are all killed before calling zap_pending, and their completion
handler should have cleared their inflight flag.
Do not 0 the data inflight flags, and add a check for try_complete succeeding,
as it should always succeed when called from zap_pending.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drop the whole dance with first moving cmnds to a dead-list. The resetting
flag ensures that no new cmds / urbs will be submitted, and that any urb
completions are short-circuited without trying to complete the scsi cmnd.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that we no longer drop our lock to unlink the data urbs, we can simply
free them on completion, making their handling consistent with the other urbs.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need for all the trickery with dropping the lock, we can
simply reference the urbs while we hold the lock to ensure the urbs don't
disappear beneath us, and do the actual unlink (+ unreference) after we've
dropped the lock.
This also fixes a race where we may loose of cmnd ownership to the scsi
midlayer without holding the lock due to the midlayer re-claiming ownership
through an abort (which will be handled by a future patch in this series).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The status urb should not complete before the command has been submitted, nor
should we get a second status urb for the same tag after a IU_ID_STATUS.
Data urbs should not complete before the command has been submitted, but may
complete after the IU_ID_STATUS.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Using scsi_host_find_tag with tags returned by the device is unsafe for
multiple reasons:
1) It returns tags->rqs[tag], which may be non NULL even when the cmnd is
not owned by us
2) It returns tags->rqs[tag], without holding any locks protecting it
3) It returns tags->rqs[tag], without doing any boundary checking
Instead keep our own list which maps tags -> inflight cmnds.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Factor out the mapping of scsi-tags -> uas-tags/stream-ids to a helper function
so that there is a single place where this "magic" happens.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Make sure we always hold the lock when setting / checking resetting
- Check resetting before checking urb->status
- Add missing check for resetting to uas_data_cmplt
- Add missing check for resetting to uas_do_work
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are various bug reports about oopses / hangs with the uas driver,
which all point to the abort-command and logical-unit-reset (task-management)
error handling paths.
Getting these right is very hard, there are quite a few corner cases, and
testing is almost impossible since under normal operation these code paths
are not used at all.
Another problem is that there are also some cases where it simply is not clear
what to do at all. E.g. over usb-2 multiple outstanding commands share the same
endpoint. What if a command gets aborted while its sense urb is half way
through completing (so some data has been transfered but not all). Since the
urb is not yet complete we don't know if the sense urb is actually for this
command, or for one of the other oustanding commands. If it is for one of the
other commands and we cancel it, then we end up in an undefined state. But if
it is actually for the command we're aborting, and the abort succeeds, then it
may never complete...
This exact same problem applies to logical unit resets too, if there are
multiple luns, then commands outstanding on both luns share the sense
endpoint. If there is only a single lun, then doing a logical unit reset is
little better then doing a full usb device reset.
So summarizing because:
1) abort / lun-reset is very tricky to get right
2) Not being able to test the tricky code, which means it will have bugs
3) This being a code path which under normal operation will never happen,
so being slow / sub-optimal here is not really an issue
4) Under error conditions we will still be able to recover through usb
device resets.
5) This may be a bit slower in some cases, but this is actually faster in
cases where the bridge ship has locked up, which seems to be the most
common error case sofar.
This commit removes the abort / lun-reset error handling paths, and also the
taks-mgmt code since those are the only 2 task-mgmt users. Leaving only the
(tested and testable) usb-device-reset error handling path in place.
Note I realize that this is somewhat of a big hammer, but currently people
are seeing very hard to debug oopses with uas. First let focus on making uas
work reliable, then we can later look into adding more fine grained error
handling.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As most ASM1051 based devices, this one has unfixable issues with uas too.
Cc: stable@vger.kernel.org # 3.16
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Besides the ASM1051 (*) needing sdev->no_report_opcodes = 1, it turns out that
the JMicron JMS567 also needs it to work properly with uas (usb-storage always
sets it). Since some of the scsi devs were not to keen on the idea to
outrightly set sdev->no_report_opcodes = 1 for all uas devices, so add a quirk
for this, and set it for the JMS567.
*) Which has become a non-issue since we've completely blacklisted uas on
the ASM1051 for other reasons
Cc: stable@vger.kernel.org
Reported-and-tested-by: Claudio Bizzarri <claudio.bizzarri@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
And set this quirk for the Seagate Expansion Desk (0bc2:2312), as that one
seems to hang upon receiving an ATA_12 or ATA_16 command.
https://bugzilla.kernel.org/show_bug.cgi?id=79511https://bbs.archlinux.org/viewtopic.php?id=183190
While at it also add missing documentation for the u value for usb-storage
quirks.
Cc: stable@vger.kernel.org # 3.16, 3.17
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
--
Changes in v2: Add documentation for new t and u usb-storage.quirks flags
Changes in v3: Fix typo in documentation
Changes in v4: Also apply the quirk to (0bc2:3312)
Changes in v5: Rebased on 3.17-rc5, drop u documentation, already upstream
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
on some architecture spin_is_locked() always return false in
uniprocessor configuration and therefore it would be advise
to replace with lockdep_assert_held().
Signed-off-by: Sanjeev Sharma <Sanjeev_Sharma@mentor.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds quirks for Entrega Technologies (later Xircom PortGear) USB-
SCSI converters. They use Shuttle Technology EUSB-01/EUSB-S1 chips. The
US_FL_SCM_MULT_TARG quirk is needed to allow multiple devices on the SCSI
chain to be accessed. Without it only the (single) device with SCSI ID 0
can be used.
The standalone converter sold by Entrega had model number U1-SC25. Xircom
acquired Entrega and re-branded the product line PortGear. The PortGear USB
to SCSI Converter (model PGSCSI) is internally identical to the Entrega
product, but later models may use a different USB ID. The Entrega-branded
units have USB ID 1645:0007, as does my Xircom PGSCSI, but the Windows and
Macintosh drivers also support 085A:0028.
Entrega also sold the "Mac USB Dock", which provides two USB ports, a Mac
(8-pin mini-DIN) serial port and a SCSI port. It appears to the computer as
a four-port hub, USB-serial, and USB-SCSI converters. The USB-SCSI part may
have initially used the same ID as the standalone U1-SC25 (1645:0007), but
later production used 085A:0026.
My Xircom PortGear PGSCSI has bcdDevice=0x0100. Units with bcdDevice=0x0133
probably also exist.
This patch adds quirks for 1645:0007, 085A:0026 and 085A:0028. The Windows
driver INF file also mentions 085A:0032 "PortStation SCSI Module", but I
couldn't find any mention of that actually existing in the wild; perhaps it
was cancelled before release?
Signed-off-by: Mark Knibbs <markk@clara.co.uk>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hi,
The Ariston Technologies iConnect 025 and iConnect 050 (also known as e.g.
iSCSI-50) are SCSI-USB converters which use Shuttle Technology/SCM
Microsystems chips. Only the connectors differ; both have the same USB ID.
The US_FL_SCM_MULT_TARG quirk is required to use SCSI devices with ID other
than 0.
I don't have one of these, but based on the other entries for Shuttle/
SCM-based converters this patch is very likely correct. I used 0x0000 and
0x9999 for bcdDeviceMin and bcdDeviceMax because I'm not sure which
bcdDevice value the products use.
Signed-off-by: Mark Knibbs <markk@clara.co.uk>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Adaptec USBConnect 2000 is another SCSI-USB converter which uses
Shuttle Technology/SCM Microsystems chips. The US_FL_SCM_MULT_TARG quirk is
required to use SCSI devices with ID other than 0.
I don't have a USBConnect 2000, but based on the other entries for Shuttle/
SCM-based converters this patch is very likely correct. I used 0x0000 and
0x9999 for bcdDeviceMin and bcdDeviceMax because I'm not sure which
bcdDevice value the product uses.
Signed-off-by: Mark Knibbs <markk@clara.co.uk>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SCSI specification requires that the second Command Data Byte
should contain the LUN value in its high-order bits if the recipient
device reports SCSI level 2 or below. Nevertheless, some USB
mass-storage devices use those bits for other purposes in
vendor-specific commands. Currently Linux has no way to send such
commands, because the SCSI stack always overwrites the LUN bits.
Testing shows that Windows 7 and XP do not store the LUN bits in the
CDB when sending commands to a USB device. This doesn't matter if the
device uses the Bulk-Only or UAS transports (which virtually all
modern USB mass-storage devices do), as these have a separate
mechanism for sending the LUN value.
Therefore this patch introduces a flag in the Scsi_Host structure to
inform the SCSI midlayer that a transport does not require the LUN
bits to be stored in the CDB, and it makes usb-storage set this flag
for all devices using the Bulk-Only transport. (UAS is handled by a
separate driver, but it doesn't really matter because no SCSI-2 or
lower device is at all likely to use UAS.)
The patch also cleans up the code responsible for storing the LUN
value by adding a bitflag to the scsi_device structure. The test for
whether to stick the LUN value in the CDB can be made when the device
is probed, and stored for future use rather than being made over and
over in the fast path.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Tiziano Bacocco <tiziano.bacocco@gmail.com>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The Iomega Jaz USB Adapter is a SCSI-USB converter cable. The hardware
seems to be identical to e.g. the Microtech XpressSCSI, using a Shuttle/
SCM chip set. However its firmware restricts it to only work with Jaz
drives.
On connecting the cable a message like this appears four times in the log:
reset full speed USB device number 4 using uhci_hcd
That's non-fatal but the US_FL_SINGLE_LUN quirk fixes it.
Signed-off-by: Mark Knibbs <markk@clara.co.uk>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are a large numbers of issues with ASM1051 devices in uas mode:
1) They do not support REPORT SUPPORTED OPERATION CODES
2) They use out of spec 8 byte status iu-s when they have no sense data,
switching to normal 16 byte status iu-s when they do have sense data.
3) They hang / crash when combined with some disks, e.g. a Crucial M500 ssd.
4) They hang / crash when stressed (through e.g. sg_reset --bus) with disks
with which then normally do work (once 1 & 2 are worked around).
Where as in BOT mode they appear to work fine, so the best way forward with
these devices is to just blacklist them for uas usage.
Unfortunately this is easier said then done. as older versions of the ASM1053
(which works fine) use the same usb-id as the ASM1051.
When connected over USB-3 the 2 can be told apart by the number of streams
they support. So this patch adds some less then pretty code to disable uas for
the ASM1051. When connected over USB-2, simply disable uas alltogether for
devices with the shared usb-id.
Cc: stable@vger.kernel.org # 3.16
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The uSCSI from Newer Technology is a SCSI-USB converter with USB ID 06ca:2003.
Like several other SCSI-USB products, it's a Shuttle Technology OEM device.
Without a suitable entry in unusual-devs.h, the converter can only access the
(single) device with SCSI ID 0. Copying the entry for device 04e6:0002 allows
it to work with devices with other SCSI IDs too.
There are currently six entries for Shuttle-developed SCSI-USB devices in
unusual-devs.h (grep for euscsi):
04e6:0002 Shuttle eUSCSI Bridge USB_SC_DEVICE, USB_PR_DEVICE
04e6:000b Shuttle eUSCSI Bridge USB_SC_SCSI, USB_PR_BULK
04e6:000c Shuttle eUSCSI Bridge USB_SC_SCSI, USB_PR_BULK
050d:0115 Belkin USB SCSI Adaptor USB_SC_SCSI, USB_PR_BULK
07af:0004 Microtech USB-SCSI-DB25 USB_SC_DEVICE, USB_PR_DEVICE
07af:0005 Microtech USB-SCSI-HD50 USB_SC_DEVICE, USB_PR_DEVICE
lsusb -v output for the uSCSI lists
bInterfaceSubClass 6 SCSI
bInterfaceProtocol 80 Bulk (Zip)
This patch adds an entry for the uSCSI to unusual_devs.h.
Signed-off-by: Mark Knibbs <markk@clara.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch set consists of the usual driver updates (ufs, storvsc, pm8001
hpsa). It also has removal of the user space target driver code (everyone is
using LIO now), a partial PCI MSI-X update, more multi-queue updates,
conversion to 64 bit LUNs (so we could theoretically cope with any LUN
returned by a device) and placeholder support for the ZBC device type (Shingle
drives), plus an assortment of minor updates and bug fixes.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJT4mS9AAoJEDeqqVYsXL0Mq34H/2AeXiM8GEVO3PIsBtF3TFZ9
poJvAyb8t//+VwAIVLHU9wrssIrIcyvNQmNHH/InGt5rOaXwGQRsnEc73bBtot4b
aC1t+hAnp2Ddvu6phmyUg7iY2GmQhAoZmeaj7krGIu2XgtLGiPg26eSsgk4Yv/U9
cuULEuOc/UnTj3w5VK8SvpyXMybVF6oQhSrS1slOglfFwPTlTI/NHU9xo7Wc3qHT
VifHXNphIvye5EH8zwtKX5p8qCrFW0pevJwyfPz7Hp2CTA9XYKx3SoeOh+n9F9ez
udBBggg7Vb1tb4mPKUoZ78UrtCVdFSCmesBU/RJe7cIh8daKaO5MVr3WPSx2JhM=
=yGai
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This patch set consists of the usual driver updates (ufs, storvsc,
pm8001 hpsa). It also has removal of the user space target driver
code (everyone is using LIO now), a partial PCI MSI-X update, more
multi-queue updates, conversion to 64 bit LUNs (so we could
theoretically cope with any LUN returned by a device) and placeholder
support for the ZBC device type (Shingle drives), plus an assortment
of minor updates and bug fixes"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (143 commits)
scsi: do not issue SCSI RSOC command to Promise Vtrak E610f
vmw_pvscsi: Use pci_enable_msix_exact() instead of pci_enable_msix()
pm8001: Fix invalid return when request_irq() failed
lpfc: Remove superfluous call to pci_disable_msix()
isci: Use pci_enable_msix_exact() instead of pci_enable_msix()
bfa: Use pci_enable_msix_exact() instead of pci_enable_msix()
bfa: Cleanup bfad_setup_intr() function
bfa: Do not call pci_enable_msix() after it failed once
fnic: Use pci_enable_msix_exact() instead of pci_enable_msix()
scsi: use short driver name for per-driver cmd slab caches
scsi_debug: support scsi-mq, queues and locks
Drivers: add blist flags
scsi: ufs: fix endianness sparse warnings
scsi: ufs: make undeclared functions static
bnx2i: Update driver version to 2.7.10.1
pm8001: fix a memory leak in nvmd_resp
pm8001: fix update_flash
pm8001: fix a memory leak in flash_update
pm8001: Cleaning up uninitialized variables
pm8001: Fix to remove null pointer checks that could never happen
...
Here is the big USB driver update for 3.17-rc1.
Loads of gadget driver changes in here, including some big file
movements to make things easier to manage over time. There's also the
usual xhci and uas driver updates, and a handful of other changes in
here. The changelog has the full details.
All of these have been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlPf2ZIACgkQMUfUDdst+ylvQwCfQKPKcwhtq4vJ2imUzJROEZwN
ygYAnRpFpH/19X59uGSdE7DAdhbitqKg
=uPh1
-----END PGP SIGNATURE-----
Merge tag 'usb-3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB updates from Greg KH:
"Here is the big USB driver update for 3.17-rc1.
Loads of gadget driver changes in here, including some big file
movements to make things easier to manage over time. There's also the
usual xhci and uas driver updates, and a handful of other changes in
here. The changelog has the full details.
All of these have been in linux-next for a while"
* tag 'usb-3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (211 commits)
USB: devio: fix issue with log flooding
uas: Log a warning when we cannot use uas because the hcd lacks streams
uas: Only complain about missing sg if all other checks succeed
xhci: Add missing checks for xhci_alloc_command failure
xhci: Rename Asrock P67 pci product-id to EJ168
xhci: Blacklist using streams on the Etron EJ168 controller
uas: Limit qdepth to 32 when connected over usb-2
uwb/whci: use correct structure type name in sizeof
usb-core bInterval quirk
USB: serial: ftdi_sio: Add support for new Xsens devices
USB: serial: ftdi_sio: Annotate the current Xsens PID assignments
usb: chipidea: debug: fix sparse non static symbol warnings
usb: ci_hdrc_imx doc: fsl,usbphy is required
usb: ci_hdrc_imx: Return -EINVAL for missing USB PHY
usb: core: allow zero packet flag for interrupt urbs
usb: lvstest: Fix sparse warnings generated by kbuild test bot
USB: core: hcd-pci: free IRQ before disabling PCI device when shutting down
phy: miphy365x: Represent each PHY channel as a DT subnode
phy: miphy365x: Provide support for the MiPHY356x Generic PHY
phy: miphy365x: Add Device Tree bindings for the MiPHY365x
...
So that an user who wants to use uas can see why he is not getting uas.
Also move the check down so that we don't warn if there are other reasons
why uas cannot work.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't complain about controllers without sg support if there are other
reasons why uas cannot be used anyways.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some jmicron uas chipsets act up (they disconnect from the bus) when sending
more then 32 commands to them at once.
Rather then building an ever growing list with usb-id based quirks for
devices using this chipset, simply reduce the qdepth to 32 when connected
over usb-2. 32 should be plenty to keep things close to maximum
possible throughput on usb-2.
Cc: stable@vger.kernel.org
Tested-and-reported-by: Laszlo T. <tlacix@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver hasn't been fully cleaned up and it doesn't look like anyone
is working on it anymore (including the original author). So remove the
driver and all references to it. If someone wants to finish cleaning
the driver up and moving it out of staging, this commit can be reverted.
Signed-off-by: Kristina Martšenko <kristina.martsenko@gmail.com>
Cc: Cho, Yu-Chen <acho@novell.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SCSI standard defines 64-bit values for LUNs, and large arrays
employing large or hierarchical LUN numbers become more and more
common.
So update the linux SCSI stack to use 64-bit LUN numbers.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Christoph Hellwig <hch@infradead.org>
Reviewed-by: Ewan Milne <emilne@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Obsolete; either use 'max_lun' if the host supports only a
limited number of LUNs or BLIST_NOLUN if the target has
problems addressing more than one LUN.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Ewan Milne <emilne@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Some buggy JMicron USB-ATA bridges don't know how to translate the FUA
bit in READs or WRITEs. This patch adds an entry in unusual_devs.h
and a blacklist flag to tell the sd driver not to use FUA.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Michael Büsch <m@bues.ch>
Tested-by: Michael Büsch <m@bues.ch>
Acked-by: James Bottomley <James.Bottomley@HansenPartnership.com>
CC: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This issue was reported by coccicheck using the semantic patch
at scripts/coccinelle/api/memdup.cocci
Signed-off-by: Benoit Taine <benoit.taine@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Even if the USB-to-ATAPI converter supported multiple LUNs, this
driver would always detect the same physical device or media because
it doesn't use srb->device->lun in any way.
Tested with an Hewlett-Packard CD-Writer Plus 8200e.
Signed-off-by: Daniele Forsi <dforsi@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are also two allocations with GFP_KERNEL in the pre-/post_reset
code paths. That is no good because that is a part of the SCSI error handler.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
intfdata is set only after scsi_scan(). uas_pre_reset() however
needs intfdata to be valid and will follow the NULL pointer
killing khubd. intfdata must be preemptively set before the
host is registered and undone in the error case.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Quote Dan:
The patch e36e64930cff: "uas: Use GFP_NOIO rather then GFP_ATOMIC
where possible" from Nov 7, 2013, leads to the following static
checker warning:
drivers/usb/storage/uas.c:806 uas_eh_task_mgmt()
error: scheduling with locks held: 'spin_lock:lock'
Some other allocations under spinlock are not caught.
The fix essentially reverts e36e64930c
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On some older XHCIs streams are not supported and the UAS driver
will fail at probe time. For those devices storage should try
to bind to UAS devices.
This patch adds a flag for stream support to HCDs and evaluates
it.
[Note: Sarah fixed a bug where the USB 2.0 root hub, not USB 3.0 root
hub would get marked as being able to support streams.]
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Although an interesting concept, I don't think that this is a good idea:
-This will result in lots of "virtual" scsi controllers confusing users
-If we get a scsi-bus-reset we will now need to do a usb-device-reset of all
uas devices on the same usb bus, which is something to avoid if possible
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
At the kernel-summit Sarah Sharp asked me if I was willing to become the
uas maintainer. I said yes, and here is a patch to make this official.
Also remove Matthew Wilcox and Sarah Sharp as maintainers at their request.
I've also added myself to the module's author tag, so that if people look there
rather then in maintainers they will know they should bug me about uas too.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
xhci streams support is fixed, unblock usb attached scsi.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Copy the sg alignment trick from the usb-storage driver, without this I'm
seeing intermittent errors when using uas devices with an ehci controller.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
The scsi error handling path re-uses previously queued up (and errored-out)
cmds. If such a re-used cmd had a data-phase then cmdinfo will have
data_in_urb / data_out_urb still set to the free-ed urbs from the errored-out
cmd, and they will get free-ed a second time when the error handling cmd
completes, corrupting the kernel heap.
Clearing cmdinfo on command queue-ing fixes this, and seems like a good idea
in general.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
The scsi-host structure is refcounted, scsi_remove_host tears down the
scsi-host but does not decrement the refcount, so we need to call
scsi_put_host on disconnect to get the underlying memory to be freed.
After calling scsi_remove_host, the scsi-core may still hold a reference to
the scsi-host, iow we may still get called after uas_disconnect, but we
do our own life cycle management of uas_devinfo, freeing it on disconnect,
and thus may end up using devinfo after it has been freed. Switch to letting
scsi_host_alloc allocate and manage the memory for us.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
cmds are either on the inflight list or on the dead list, never both, so
we only need one list head.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Before this commit the uas driver would keep track of scsi commands which still
need to have some urbs submitted to the device, and complete this with an
ABORT result code on bus-reset or disconnect, but in flight scsi commands
which have all their urbs submitted, and thus are not part of the work list,
would never get their done callback called.
The problem is killed sense urbs don't have any tag info, so it is impossible
to tell which scsi cmd they belong to, so merely making sure all the urbs
have completed one way or the other is not enough.
This commit fixes this by changing the work list to an inflight list, which
keeps tracks of all inflight scsi cmnds, using the IS_IN_WORK_LIST flag to
determine if actual work needs to be done in uas_do_work(), and by moving
marking all inflight scsi commands as aborted and moving them to the dead list
on bus-reset or disconnect.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
uas_alloc_data_urb always gets called with a stream_id value of 0 when not
using streams. Removing the check makes it consistent with uas_alloc_sense_urb.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
For USB-2 connections the stream-id must always be 0.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Some BIOS-es will hang on reboot when an uas device is attached and left in
uas mode on reboot.
This commit adds a shutdown handler which on reboot puts the device back into
usb-storage mode, fixing the hang on reboot on these systems.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
We can sleep in our own workqueue (which is the whole reason for having
it), and scsi error handlers are also always called from a context which
may sleep.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Since we use a fixed tag / stream for tasks we cannot allow more then one
to run at the same time. This could happen before this time if a task timed
out.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
The fixed endpoint config code was only necessary to deal with an early
uas prototype which has never been released, so lets drop it and enforce
proper uas endpoint descriptors.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
The loop uses up to 3 bytes of the endpoint extra data.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This is a preparation patch for adding better descriptor validation.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Dmitry Katsubo