Ryzen 2700X has a temperature offset of 10 degrees C. If bit 19 of the
Temperature Control register is set, there is an additional offset of
49 degrees C. Take this into account as well.
Cc: stable@vger.kernel.org # v4.16+
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
On Asrock Z370M Pro4, it was observed that EC access was disabled after
initially booting the system. As a result, the driver failed to load
with
nct6683: EC is disabled
After a suspend/resume cycle, the driver loaded correctly.
nct6683: Found NCT6683D or compatible chip at 0x2e:0xa20
nct6683 nct6683.2592: NCT6683D EC firmware version 1.0 build 07/18/16
Enable EC access after identifying the chip if disabled to fix the problem.
Warn the user that the data it reports may be unusable, similar to other
drivers for chips from Nuvoton.
Fixes: 41082d66bf ("hwmon: Driver for NCT6683D")
Reported-by: Jonathan Sims <jonathan.625266@earthlink.net>
Tested-by: Jonathan Sims <jonathan.625266@earthlink.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Currently the loop checks for non-zero count of sensors for each type
of sensors which is completely wrong. It also results in aborting the
registration of sensors if one or more types of sensors are completely
not supported by the platform SCMI firmware.
This patch fixes the issue by continue to loop and skiping sensor types
that are not present.
Fixes: b23688aefb ("hwmon: add support for sensors exported via ARM SCMI")
Reported-by: Jim Quinlan <james.quinlan@broadcom.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: linux-hwmon@vger.kernel.org
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The uid and die temperature can be read out on the ADIN7 using
input mux. Map uid and die temperature sensor to channels 16
and 17.
Signed-off-by: Andrey Gusakov <andrey.gusakov@cogentembedded.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
New centaur CPUs (Familiy == 7) also support this cpu temperature sensor.
Signed-off-by: David Wang <davidwang@zhaoxin.com>
[groeck: Dropped changelog, updated subject]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
pwmX_mode is defined in the ABI as 0=DC mode, 1=pwm mode. The chip
register bit is set to 1 for DC mode. This got mixed up, and writing
1 into pwmX_mode resulted in DC mode enabled. Fix it up by using
the ABI definition throughout the driver for consistency.
Fixes: 77eb5b3703 ("hwmon: (nct6775) Add support for pwm, pwm_mode, ... ")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Couple of fixes for build warning due to uninitialised variable
and static checker warning for passing NULL pointer to PTR_ERR.
It also contains cleanup suggested by Stephen Boyd in SCMI clock
driver using the new devm_of_clk_add_hw_provider() API.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Gvhw
-----END PGP SIGNATURE-----
Merge tag 'scmi-fixes-4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into next/drivers
Pull "ARM SCMI fixes/cleanups for v4.17" from Sudeep Holla:
Couple of fixes for build warning due to uninitialised variable
and static checker warning for passing NULL pointer to PTR_ERR.
It also contains cleanup suggested by Stephen Boyd in SCMI clock
driver using the new devm_of_clk_add_hw_provider() API.
* tag 'scmi-fixes-4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
clk: scmi: use devm_of_clk_add_hw_provider() API and drop scmi_clocks_remove
firmware: arm_scmi: prevent accessing rate_discrete uninitialized
hwmon: (scmi) return -EINVAL when sensor information is unavailable
Since autodetection of this chip was removed, it makes sense to add prefix
max6635 so that the device can be instantiated by its actual name.
Signed-off-by: Alvaro Gamez Machado <alvaro.gamez@hazent.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Maxim MAX663x family are mostly compatible with LM92, but they lack any
identification register. Weakening the detect function would make it prone
to false positives, and current one doesn't detect all chips. Therefore,
the detect function for max6635 devices is removed in favor of explicit
device instatiation.
Signed-off-by: Alvaro Gamez Machado <alvaro.gamez@hazent.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Passing NULL pointer to PTR_ERR will result in return value of 0
indicating success which is clearly not what it is intended here.
This patch returns -EINVAL instead when the sensor information is not
available.
Fixes: b23688aefb ("hwmon: add support for sensors exported via ARM SCMI")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Cc: linux-hwmon@vger.kernel.org
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Expose the gpiN_fault fields of mfr_status as individual debugfs
attributes. This provides a way for users to be easily notified of gpi
faults. Also provide the whole mfr_status register in debugfs.
Signed-off-by: Christopher Bostic <cbostic@linux.vnet.ibm.com>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Eddie James <eajames@linux.vnet.ibm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add a struct gpio_chip and define some methods so that this device's
I/O can be accessed via /sys/class/gpio.
Signed-off-by: Christopher Bostic <cbostic@linux.vnet.ibm.com>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Eddie James <eajames@linux.vnet.ibm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
NCT6796D is mostly compatible to NCT6795D. It supports an additional
pwm control and fan speed channel.
While we are at it, update documentation for NCT6795D.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Initialize boolean flags in nct6775_check_fan_inputs() while
declaring them instead of several times throughout the code.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Improve fan6/pwm6 detection on NCT6795D. Add support for fan pulses
for fans 4..6 and fan min limits for fan6.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The size of some of the arrays using the number of fans is hardcoded.
Use NUM_FAN consistently throughout the driver.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Simplify code and use devm_add_action() to handle cleanup.
Signed-off-by: Peng Hao <peng.hao2@zte.com.cn>
[groeck: Dropped unnecessary dummy function and NULL check]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The previously used URLs are dead.
Sensirion provides permalinks for their product datasheets at
https://www.sensirion.com/en/about-us/links/.
Signed-off-by: Danilo Bargen <mail@dbrgn.ch>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
A negative page register value means that no page needs to be
selected. This is used by status register read operations and needs
to be accepted. The failure to do so so results in missed status
and limit registers.
Fixes: da8e48ab48 ("hwmon: (pmbus) Always call _pmbus_read_byte in core driver")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
A negative page register value means that no page needs to be
selected. This is used by status register evaluations and needs
to be accepted.
Fixes: da8e48ab48 ("hwmon: (pmbus) Always call _pmbus_read_byte in core driver")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
ARM System Control and Management Interface(SCMI)[1] is more flexible and
easily extensible than any of the existing interfaces.
Few existing as well as future ARM platforms provide micro-controllers
to abstract various power and other system management tasks which have
similar interfaces, both in terms of the functions that are provided by
them, and in terms of how requests are communicated to them.
There are quite a few protocols like ARM SCPI, TI SCI, QCOM RPM, Nvidia Tegra
BPMP, and so on already. This specification is to standardize and avoid any
further fragmentation in the design of such interface by various vendors.
The current SCMI driver implementation is very basic and initial support.
It lacks support for notifications, asynchronous/delayed response, perf/power
statistics region and sensor register region.
Mailbox is the only form of transport supported currently in the driver.
SCMI supports interrupt based mailbox communication, where, on completion
of the processing of a message, the caller receives an interrupt as well as
polling for completion.
SCMI is designed to minimize the dependency on the mailbox/transport
hardware. So in terms of SCMI, each channel in the mailbox includes
memory area, doorbell and completion interrupt.
However the doorbell and completion interrupt is highly mailbox dependent
which was bit of controversial as part of SCMI/mailbox discussions.
Arnd and me discussed about the few aspects of SCMI and the mailbox framework:
1. Use of mailbox framework for doorbell type mailbox controller:
- Such hardware may not require any data to be sent to signal the remote
about the presence of a message. The channel will have in-built
information on how to trigger the signal to the remote.
There are few mailbox controller drivers which are purely doorbell based.
e.g.QCOM IPC, STM, Tegra, ACPI PCC,..etc
2. Supporting other mailbox controller:
- SCMI just needs a mechanism to signal the remote firmware. Such
controller may need fixed message to be sent to trigger a doorbell.
In such case we may need to get that data from DT and pass the same
to the controller. It's not covered in the current DT binding, but
can be extended as optional property in future.
However handling notifications may be interesting on such mailbox, but
again there is no way to interpret what the data field(remote message)
means, it could be a bit mask or a number or don't-care.
Arnd mentioned that he doesn't like the way the mailbox binding deals
with doorbell-type hardware, but we do have quite a few precedent drivers
already and changing the binding to add a data field would not make it any
better, but could cause other problems. So he is happy with the status quo
of SCMI implementation.
[1] http://infocenter.arm.com/help/index.jsp?topic=/com.arm.doc.den0056a/index.html
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=qOck
-----END PGP SIGNATURE-----
Merge tag 'scmi-updates-4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into next/drivers
Pull "ARM SCMI support for v4.17" from Sudeep Holla:
ARM System Control and Management Interface(SCMI)[1] is more flexible and
easily extensible than any of the existing interfaces.
Few existing as well as future ARM platforms provide micro-controllers
to abstract various power and other system management tasks which have
similar interfaces, both in terms of the functions that are provided by
them, and in terms of how requests are communicated to them.
There are quite a few protocols like ARM SCPI, TI SCI, QCOM RPM, Nvidia Tegra
BPMP, and so on already. This specification is to standardize and avoid any
further fragmentation in the design of such interface by various vendors.
The current SCMI driver implementation is very basic and initial support.
It lacks support for notifications, asynchronous/delayed response, perf/power
statistics region and sensor register region.
Mailbox is the only form of transport supported currently in the driver.
SCMI supports interrupt based mailbox communication, where, on completion
of the processing of a message, the caller receives an interrupt as well as
polling for completion.
SCMI is designed to minimize the dependency on the mailbox/transport
hardware. So in terms of SCMI, each channel in the mailbox includes
memory area, doorbell and completion interrupt.
However the doorbell and completion interrupt is highly mailbox dependent
which was bit of controversial as part of SCMI/mailbox discussions.
Arnd and me discussed about the few aspects of SCMI and the mailbox framework:
1. Use of mailbox framework for doorbell type mailbox controller:
- Such hardware may not require any data to be sent to signal the remote
about the presence of a message. The channel will have in-built
information on how to trigger the signal to the remote.
There are few mailbox controller drivers which are purely doorbell based.
e.g.QCOM IPC, STM, Tegra, ACPI PCC,..etc
2. Supporting other mailbox controller:
- SCMI just needs a mechanism to signal the remote firmware. Such
controller may need fixed message to be sent to trigger a doorbell.
In such case we may need to get that data from DT and pass the same
to the controller. It's not covered in the current DT binding, but
can be extended as optional property in future.
However handling notifications may be interesting on such mailbox, but
again there is no way to interpret what the data field(remote message)
means, it could be a bit mask or a number or don't-care.
Arnd mentioned that he doesn't like the way the mailbox binding deals
with doorbell-type hardware, but we do have quite a few precedent drivers
already and changing the binding to add a data field would not make it any
better, but could cause other problems. So he is happy with the status quo
of SCMI implementation.
[1] http://infocenter.arm.com/help/index.jsp?topic=/com.arm.doc.den0056a/index.html
* tag 'scmi-updates-4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
cpufreq: scmi: add support for fast frequency switching
cpufreq: add support for CPU DVFS based on SCMI message protocol
hwmon: add support for sensors exported via ARM SCMI
hwmon: (core) Add hwmon_max to hwmon_sensor_types enumeration
clk: add support for clocks provided by SCMI
firmware: arm_scmi: add device power domain support using genpd
firmware: arm_scmi: add per-protocol channels support using idr objects
firmware: arm_scmi: refactor in preparation to support per-protocol channels
firmware: arm_scmi: add option for polling based performance domain operations
firmware: arm_scmi: add support for polling based SCMI transfers
firmware: arm_scmi: probe and initialise all the supported protocols
firmware: arm_scmi: add initial support for sensor protocol
firmware: arm_scmi: add initial support for power protocol
firmware: arm_scmi: add initial support for clock protocol
firmware: arm_scmi: add initial support for performance protocol
firmware: arm_scmi: add scmi protocol bus to enumerate protocol devices
firmware: arm_scmi: add common infrastructure and support for base protocol
firmware: arm_scmi: add basic driver infrastructure for SCMI
dt-bindings: arm: add support for ARM System Control and Management Interface(SCMI) protocol
dt-bindings: mailbox: add support for mailbox client shared memory
Create a driver to add support for SoC sensors exported by the System
Control Processor (SCP) via the System Control and Management Interface
(SCMI). The supported sensor types is one of voltage, temperature,
current, and power.
The sensor labels and values provided by the SCP are exported via the
hwmon sysfs interface.
Cc: linux-hwmon@vger.kernel.org
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJahgQ1AAoJEMsfJm/On5mBNfgQAJgCjg4gatr0U2pqd40IPtwS
V/KrAfLtt9+zv6HSdW1zc1vUKb3mAvi9roVIX6i4nuSjS9eitPRyvcSN+UW9X01t
r8jqwtStssaXEKLzRkEGBoACy7/A0fNCcjHMOj1EPftKIOZdfGnZ6r4cI+/wGyLR
ybBjcvfMNkLGgJbRKy/2Acib/Jp9OoJpjLMVyIFnhRGgRmvYKSDu7rK6ecmW2KSG
mgKyzxL29PLfWu8jVwnkXfZcdG97akEv90BfUUa16KXA3+hgvscM5+7jQmap4N3p
nh3yLc7MyTXvfOhKauer4czTwbr3JoDZ+BZ38a1qoD+cPX6e5GkGJnFR1E0NBG/p
7m2w1u7LVhab5t7NFA8JgKB8J8PfyGVCiHfF0szil6lA0LiRVN/rgMcAEIavIO7K
7C5OBjVYWk0PeJULU66r81kILvZMtc6xh6XC2gc8Z+t6uu4Ld4FSUsIWL6Muu0l6
i2h8WX5HSMjSqCylPBTRD0a/hvPuQjWE0fkLoAtgPCt112Je6xitJzZM+RPDKonV
8+zG1NM9eePnSNt3TsdMeF6HOR9fR9n7E3D0xsM2cbHXa1BOwlVCkPYYqNA6QkaM
ZKTRKysZn3fYfMT0fVfdZ7E0ODZPpY/gwdqE4bduH9pMksqO0E2/g9PX/JQV13bN
IwpMFO9aHMqVc+U8Xwhu
=kHhI
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-linus-v4.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fix from Guenter Roeck:
"Fix bad temperature display on Ryzen/Threadripper"
* tag 'hwmon-for-linus-v4.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (k10temp) Only apply temperature offset if result is positive
Pull x86 PTI and Spectre related fixes and updates from Ingo Molnar:
"Here's the latest set of Spectre and PTI related fixes and updates:
Spectre:
- Add entry code register clearing to reduce the Spectre attack
surface
- Update the Spectre microcode blacklist
- Inline the KVM Spectre helpers to get close to v4.14 performance
again.
- Fix indirect_branch_prediction_barrier()
- Fix/improve Spectre related kernel messages
- Fix array_index_nospec_mask() asm constraint
- KVM: fix two MSR handling bugs
PTI:
- Fix a paranoid entry PTI CR3 handling bug
- Fix comments
objtool:
- Fix paranoid_entry() frame pointer warning
- Annotate WARN()-related UD2 as reachable
- Various fixes
- Add Add Peter Zijlstra as objtool co-maintainer
Misc:
- Various x86 entry code self-test fixes
- Improve/simplify entry code stack frame generation and handling
after recent heavy-handed PTI and Spectre changes. (There's two
more WIP improvements expected here.)
- Type fix for cache entries
There's also some low risk non-fix changes I've included in this
branch to reduce backporting conflicts:
- rename a confusing x86_cpu field name
- de-obfuscate the naming of single-TLB flushing primitives"
* 'x86-pti-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (41 commits)
x86/entry/64: Fix CR3 restore in paranoid_exit()
x86/cpu: Change type of x86_cache_size variable to unsigned int
x86/spectre: Fix an error message
x86/cpu: Rename cpu_data.x86_mask to cpu_data.x86_stepping
selftests/x86/mpx: Fix incorrect bounds with old _sigfault
x86/mm: Rename flush_tlb_single() and flush_tlb_one() to __flush_tlb_one_[user|kernel]()
x86/speculation: Add <asm/msr-index.h> dependency
nospec: Move array_index_nospec() parameter checking into separate macro
x86/speculation: Fix up array_index_nospec_mask() asm constraint
x86/debug: Use UD2 for WARN()
x86/debug, objtool: Annotate WARN()-related UD2 as reachable
objtool: Fix segfault in ignore_unreachable_insn()
selftests/x86: Disable tests requiring 32-bit support on pure 64-bit systems
selftests/x86: Do not rely on "int $0x80" in single_step_syscall.c
selftests/x86: Do not rely on "int $0x80" in test_mremap_vdso.c
selftests/x86: Fix build bug caused by the 5lvl test which has been moved to the VM directory
selftests/x86/pkeys: Remove unused functions
selftests/x86: Clean up and document sscanf() usage
selftests/x86: Fix vDSO selftest segfault for vsyscall=none
x86/entry/64: Remove the unused 'icebp' macro
...
x86_mask is a confusing name which is hard to associate with the
processor's stepping.
Additionally, correct an indent issue in lib/cpu.c.
Signed-off-by: Jia Zhang <qianyue.zj@alibaba-inc.com>
[ Updated it to more recent kernels. ]
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: bp@alien8.de
Cc: tony.luck@intel.com
Link: http://lkml.kernel.org/r/1514771530-70829-1-git-send-email-qianyue.zj@alibaba-inc.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
A user reports a really bad temperature on Ryzen 1950X.
k10temp-pci-00cb
Adapter: PCI adapter
temp1: +4294948.3°C (high = +70.0°C)
This will happen if the temperature reported by the chip is lower than
the offset temperature. This has been seen in the field if "Sense MI Skew"
and/or "Sense MI Offset" BIOS parameters were set to unexpected values.
Let's report a temperature of 0 degrees C in that case.
Fixes: 1b50b77635 ("hwmon: (k10temp) Add support for temperature offsets")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Calling fan related SMM functions implemented by Dell BIOS firmware on Dell
Vostro 3360 freeze kernel for about 500ms.
Unfortunately, it is unlikely for Dell to fix this since the machine
is pretty old, so this commit just disables fan support to make the
system usable again.
Via "force" module param fan support can be enabled.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=195751
Link: http://lkml.iu.edu/hypermail/linux/kernel/1711.2/06083.html
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Calling fan related SMM functions implemented by Dell BIOS firmware on Dell
Inspiron 7720 freeze kernel for about 500ms. Until Dell fixes it we need to
disable fan support for Dell Inspiron 7720 as it makes system unusable.
Via "force" module param fan support can be enabled.
Reported-by: vova7890@mail.ru
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=195751
Cc: stable@vger.kernel.org # v4.0+, will need backport
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Some Dell machines are broken and some functionality is disabled. Show
warning into dmesg about this fact and allow user via "force" module param
to override brokenness and enable broken functionality.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The trailing semicolon is an empty statement that does no operation.
Removing it since it doesn't do anything.
Signed-off-by: Luis de Bethencourt <luisbg@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Initialize data->config_lock mutex before it is used by the driver code.
This fixes following warning on Odroid XU3 boards:
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
CPU: 5 PID: 1 Comm: swapper/0 Not tainted 4.15.0-rc7-next-20180115-00001-gb75575dee3f2 #107
Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
[<c0111504>] (unwind_backtrace) from [<c010dbec>] (show_stack+0x10/0x14)
[<c010dbec>] (show_stack) from [<c09b3f74>] (dump_stack+0x90/0xc8)
[<c09b3f74>] (dump_stack) from [<c0179528>] (register_lock_class+0x1c0/0x59c)
[<c0179528>] (register_lock_class) from [<c017bd1c>] (__lock_acquire+0x78/0x1850)
[<c017bd1c>] (__lock_acquire) from [<c017de30>] (lock_acquire+0xc8/0x2b8)
[<c017de30>] (lock_acquire) from [<c09ca59c>] (__mutex_lock+0x60/0xa0c)
[<c09ca59c>] (__mutex_lock) from [<c09cafd0>] (mutex_lock_nested+0x1c/0x24)
[<c09cafd0>] (mutex_lock_nested) from [<c068b0d0>] (ina2xx_set_shunt+0x70/0xb0)
[<c068b0d0>] (ina2xx_set_shunt) from [<c068b218>] (ina2xx_probe+0x88/0x1b0)
[<c068b218>] (ina2xx_probe) from [<c0673d90>] (i2c_device_probe+0x1e0/0x2d0)
[<c0673d90>] (i2c_device_probe) from [<c053a268>] (driver_probe_device+0x2b8/0x4a0)
[<c053a268>] (driver_probe_device) from [<c053a54c>] (__driver_attach+0xfc/0x120)
[<c053a54c>] (__driver_attach) from [<c05384cc>] (bus_for_each_dev+0x58/0x7c)
[<c05384cc>] (bus_for_each_dev) from [<c0539590>] (bus_add_driver+0x174/0x250)
[<c0539590>] (bus_add_driver) from [<c053b5e0>] (driver_register+0x78/0xf4)
[<c053b5e0>] (driver_register) from [<c0675ef0>] (i2c_register_driver+0x38/0xa8)
[<c0675ef0>] (i2c_register_driver) from [<c0102b40>] (do_one_initcall+0x48/0x18c)
[<c0102b40>] (do_one_initcall) from [<c0e00df0>] (kernel_init_freeable+0x110/0x1d4)
[<c0e00df0>] (kernel_init_freeable) from [<c09c8120>] (kernel_init+0x8/0x114)
[<c09c8120>] (kernel_init) from [<c01010b4>] (ret_from_fork+0x14/0x20)
Fixes: 5d389b1251 ("hwmon: (ina2xx) Make calibration register value fixed")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The ir35221 datasheet describes specific scaling factors for a number of
commands which the current driver applies when reading.
However now that the ir35221 has been tested on machines with more
easily verifiable readings these descriptions have turned out to be
superfluous and reading each command according to the linear format is
sufficient.
Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
An sht3x sensor include limits register which contains temperature
and humidity limit values. After a reset, pre-defined values are loaded
into that register. During the probe function, the driver reads the
limits register. However, if the reads are made too early, and the bus
is clocked at high frequencies (e.g. 100 kHz or more), the loading could be
not completed and the sensor returns a NACK which causes the probe to fail.
A delay of at least 500 us before the first read solves this issue.
Signed-off-by: Emiliano Ingrassia <ingrassia@epigenesys.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Building without CONFIG_LEDS_CLASS causes a link failure:
drivers/hwmon/pmbus/ibm-cffps.o: In function `ibm_cffps_probe':
ibm-cffps.c:(.text+0x4f4): undefined reference to `devm_of_led_classdev_register'
This adds the required dependency.
Fixes: ef9e1cdf41 ("hwmon: (pmbus/cffps) Add led class device ...")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This power supply device doesn't correctly manage it's own fault led.
Add an led class device and register it so that userspace can manage
power supply fault led as necessary.
Signed-off-by: Eddie James <eajames@linux.vnet.ibm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This power supply device regularly fails to read VOUT_MODE due to the
CML bit going high. This results in an incorrect exponent used for the
voltage data, and therefore the power supply reports incorrect voltage.
Work around this by setting the pmbus flag to skip the CML check.
Signed-off-by: Eddie James <eajames@linux.vnet.ibm.com>
Fixes: f69316d62c ("hwmon: (pmbus) Add IBM Common Form Factor (CFF) ...")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The ASPEED SoC must deassert a reset in order to use the PWM/tach
peripheral.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add debugfs entries for additional power supply data, including part
number, serial number, FRU number, firmware revision, ccin, and the
input history of the power supply. The input history is 10 minutes of
input power data in the form of twenty 30-second packets. Each packet
contains average and maximum power for that 30 second period.
Signed-off-by: Edward A. James <eajames@us.ibm.com>
[groeck: Fixed endianness problem]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Pmbus client drivers, if they want to use debugfs, should use the same
root directory as the pmbus debugfs entries are using. Therefore, export
the device dentry for the pmbus client.
Signed-off-by: Edward A. James <eajames@us.ibm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Smatch reports:
drivers/hwmon/w83773g.c:105
get_fault() warn: shift has higher precedence than mask
Code analysis shows that the code is indeed wrong.
Fix it, and while we are at it, drop unnecessary typecast.
Fixes: 86a10c802362 ("hwmon: Add W83773G driver")
Cc: Lei YU <mine260309@gmail.com>
Reviewed-by: Lei YU <mine260309@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Sparse reports:
drivers/hwmon/hih6130.c:56: warning:
No description found for parameter 'client'
drivers/hwmon/hih6130.c:56: warning:
Excess struct member 'hwmon_dev' description in 'hih6130'
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Sparse reports:
drivers/hwmon/sht21.c:60: warning:
No description found for parameter 'client'
drivers/hwmon/sht21.c:60:
warning: Excess struct member 'hwmon_dev' description in 'sht21'
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
sparse reports:
drivers/hwmon/hwmon.c:681: warning:
No description found for parameter 'chip'
drivers/hwmon/hwmon.c:681: warning:
Excess function parameter 'info' description in
'hwmon_device_register_with_info'
drivers/hwmon/hwmon.c:789: warning:
No description found for parameter 'chip'
drivers/hwmon/hwmon.c:789: warning:
No description found for parameter 'groups'
drivers/hwmon/hwmon.c:789: warning:
Excess function parameter 'info' description in
'devm_hwmon_device_register_with_info'
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Before this patch:
$ modinfo drivers/hwmon/pmbus/max31785.ko | grep alias
alias: i2c:max31785a
alias: i2c:max31785
After this patch:
$ modinfo drivers/hwmon/pmbus/max31785.ko | grep alias
alias: i2c:max31785a
alias: i2c:max31785
alias: of:N*T*Cmaxim,max31785aC*
alias: of:N*T*Cmaxim,max31785a
alias: of:N*T*Cmaxim,max31785C*
alias: of:N*T*Cmaxim,max31785
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Calibration register is used for calculating current register in
hardware according to datasheet:
current = shunt_volt * calib_register / 2048 (ina 226)
current = shunt_volt * calib_register / 4096 (ina 219)
Fix calib_register value to 2048 for ina226 and 4096 for ina 219 in
order to avoid truncation error and provide best precision allowed
by shunt_voltage measurement. Make current scale value follow changes
of shunt_resistor from sysfs as calib_register value is now fixed.
Power_lsb value should also follow shunt_resistor changes as stated in
datasheet:
power_lsb = 25 * current_lsb (ina 226)
power_lsb = 20 * current_lsb (ina 219)
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The dual tachometer feature is implemented in hardware with a TACHSEL
input to indicate the rotor under measurement, and exposed on the device
by extending the READ_FAN_SPEED_1 word with two extra bytes*. The need
to read the non-standard four-byte response leads to a cut-down
implementation of i2c_smbus_xfer_emulated() included in the driver.
Further, to expose the second rotor tachometer value to userspace the
values are exposed through virtual pages. We re-route accesses to
FAN_CONFIG_1_2 and READ_FAN_SPEED_1 on pages 23-28 (not defined by the
hardware) to the same registers on pages 0-5, and with the latter command
we extract the value from the second word of the four-byte response.
* The documentation recommends the slower rotor be associated with
TACHSEL=0, which corresponds to the first word of the response. The
TACHSEL=0 measurement is used by the controller's closed-loop fan
management to judge target fan rate.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Some circumstances call for virtual pages, to expose multiple values
packed into an extended PMBus register in a manner non-compliant with
the PMBus standard. An example of this is the Maxim MAX31785 controller,
which extends the READ_FAN_SPEED_1 PMBus register from two to four bytes
to support tach readings for both rotors of a dual rotor fan. This extended
register contains two word-sized values, one reporting the rate of the
fastest rotor, the other the rate of the slowest. The concept of virtual
pages aids this situation by mapping the page number onto the value to be
selected from the vectored result.
We should not try to set virtual pages on the device as such a page
explicitly doesn't exist; add a flag so we can avoid doing so.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The implementation makes use of the new fan control virtual registers
exposed by the pmbus core. It mixes use of the default implementations
with some overrides via the read/write handlers to handle FAN_COMMAND_1
on the MAX31785, whose definition breaks the value range into various
control bands dependent on RPM or PWM mode.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Expose fanX_target, pwmX and pwmX_enable hwmon sysfs attributes.
Fans in a PMBus device are driven by the configuration of two registers,
FAN_CONFIG_x_y and FAN_COMMAND_x: FAN_CONFIG_x_y dictates how the fan
and the tacho operate (if installed), while FAN_COMMAND_x sets the
desired fan rate. The unit of FAN_COMMAND_x is dependent on the
operational fan mode, RPM or PWM percent duty, as determined by the
corresponding configuration in FAN_CONFIG_x_y.
The mapping of fanX_target, pwmX and pwmX_enable onto FAN_CONFIG_x_y and
FAN_COMMAND_x is implemented with the addition of virtual registers to
facilitate the necessary side-effects of each access:
1. PMBUS_VIRT_FAN_TARGET_x
2. PMBUS_VIRT_PWM_x
3. PMBUS_VIRT_PWM_ENABLE_x
Some complexity arises with the fanX_target and pwmX attributes both mapping
onto FAN_COMMAND_x: There is no general mapping between PWM percent duty and
RPM, so we can't display values in either attribute in terms of the other
(which in my mind is the intuitive, if impossible, behaviour). This problem
also affects the pwmX_enable attribute which allows userspace to switch between
full speed, manual PWM and a number of automatic control modes, possibly
including a switch to RPM behaviour (e.g. automatically adjusting PWM duty to
reach a RPM target, the behaviour of fanX_target).
The next most intuitive behaviour is for fanX_target and pwmX to simply be
independent, to retain their most recently set value even if that value is not
active on the hardware (due to switching to the alternative control mode). This
property of retaining the value independent of the hardware state has useful
results for both userspace and the kernel: Userspace always sees a sensible
value in the attribute (the last thing it was set to, as opposed to 0 or
receiving an error on read), and the kernel can use the attributes as a value
cache. This latter point eases the implementation of pwmX_enable, which can
look up the associated pmbus_sensor object, take its cached value and apply it
to hardware on changing control mode. This ensures we will not arbitrarily set
a PWM value as an RPM value or vice versa, and we can assume that the RPM or
PWM value set was sensible at least at some point in the past.
Finally, the DIRECT mode coefficients of some controllers is different between
RPM and PWM percent duty control modes, so PSC_PWM is introduced to capture the
necessary coefficients. As pmbus core had no PWM support previously PSC_FAN
continues to be used to capture the RPM DIRECT coefficients, but in order to
avoid falsely applying RPM scaling to PWM values I have introduced the
PMBUS_HAVE_PWM12 and PMB_BUS_HAVE_PWM34 feature bits. These feature bits allow
drivers to explicitly declare PWM support in order to have the attributes
exposed.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
pci_get_bus_and_slot() is restrictive such that it assumes domain=0 as
where a PCI device is present. This restricts the device drivers to be
reused for other domain numbers.
Use pci_get_domain_bus_and_slot() with a domain number of 0 where we can't
extract the domain number. Other places, use the actual domain number from
the device.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
'default n' is default, so there is no need to specify it explicitly.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Nuvoton W83773G is a hardware monitor IC providing one local
temperature and two remote temperature sensors.
Signed-off-by: Lei YU <mine260309@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
If the thermal subsystem returne -EPROBE_DEFER or any other error
when hwmon calls devm_thermal_zone_of_sensor_register(), this is
silently ignored.
I ran into this with an incorrectly defined thermal zone, making
it non-existing and thus this call failed with -EPROBE_DEFER
assuming it would appear later. The sensor was still added
which is incorrect: sensors must strictly be added after the
thermal zones, so deferred probe must be respected.
Fixes: d560168b5d ("hwmon: (core) New hwmon registration API")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
With a nxp,se97 chip on an atmel sama5d31 board, the I2C adapter driver
is not always capable of avoiding the 25-35 ms timeout as specified by
the SMBUS protocol. This may cause silent corruption of the last bit of
any transfer, e.g. a one is read instead of a zero if the sensor chip
times out. This also affects the eeprom half of the nxp-se97 chip, where
this silent corruption was originally noticed. Other I2C adapters probably
suffer similar issues, e.g. bit-banging comes to mind as risky...
The SMBUS register in the nxp chip is not a standard Jedec register, but
it is not special to the nxp chips either, at least the atmel chips
have the same mechanism. Therefore, do not special case this on the
manufacturer, it is opt-in via the device property anyway.
Cc: stable@vger.kernel.org # 4.9+
Signed-off-by: Peter Rosin <peda@axentia.se>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Power values in the 100s of watt range can easily blow past
32bit math limits when processing everything in microwatts.
Use 64bit math instead to avoid these issues on common 32bit ARM
BMC platforms.
Fixes: 442aba7872 ("hwmon: PMBus device driver")
Signed-off-by: Robert Lippert <rlippert@google.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Since i2c_unregister_device() became NULL-aware we may remove duplicate
NULL check.
Cc: Rudolf Marek <r.marek@assembler.cz>
Cc: Jean Delvare <jdelvare@suse.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: linux-hwmon@vger.kernel.org
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Since i2c_unregister_device() became NULL-aware we may remove duplicate
NULL check.
Cc: Jean Delvare <jdelvare@suse.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: linux-hwmon@vger.kernel.org
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Since i2c_unregister_device() became NULL-aware we may remove duplicate
NULL check.
Cc: Marc Hulsman <m.hulsman@tudelft.nl>
Cc: Jean Delvare <jdelvare@suse.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: linux-hwmon@vger.kernel.org
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Since i2c_unregister_device() became NULL-aware we may remove duplicate
NULL check.
Cc: Jean Delvare <jdelvare@suse.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: linux-hwmon@vger.kernel.org
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
- Drivers for MAX31785 and MAX6621
- Support for AMD family 17h (Ryzen, Threadripper) temperature sensors
- Various driver cleanups and minor improvements
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=NpxT
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-linus-v4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
- drivers for MAX31785 and MAX6621
- support for AMD family 17h (Ryzen, Threadripper) temperature sensors
- various driver cleanups and minor improvements
* tag 'hwmon-for-linus-v4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (30 commits)
dt-bindings: pmbus: Add Maxim MAX31785 documentation
pmbus: Add driver for Maxim MAX31785 Intelligent Fan Controller
hwmon: (aspeed-pwm-tacho) Sort headers
hwmon: (xgene) Minor clean up of ifdef and acpi_match_table reference
hwmon: (max6621) Inverted if condition in max6621_read()
hwmon: (asc7621) remove redundant assignment to newval
hwmon: (xgene) Support hwmon v2
hwmon: (gpio-fan) Fix null pointer dereference at probe
hwmon: (gpio-fan) Convert to use GPIO descriptors
hwmon: (gpio-fan) Rename GPIO line state variables
hwmon: (gpio-fan) Get rid of the gpio alarm struct
hwmon: (gpio-fan) Get rid of platform data struct
hwmon: (gpio-fan) Mandate OF_GPIO and cut pdata path
hwmon: (gpio-fan) Send around device pointer
hwmon: (gpio-fan) Localize platform data
hwmon: (gpio-fan) Use local variable pointers
hwmon: (gpio-fan) Move DT bindings to the right place
Documentation: devicetree: add max6621 device
hwmon: (max6621) Add support for Maxim MAX6621 temperature sensor
hwmon: (w83793) make const array watchdog_minors static, reduces object code size
...
The Maxim MAX31785 is a PMBus device providing closed-loop, multi-channel
fan management with temperature and remote voltage sensing. It supports
various fan control features, including PWM frequency control, temperature
hysteresis, dual tachometer measurements, and fan health monitoring.
This patch presents a basic driver using only the existing features of the
PMBus subsystem.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
[groeck: Modified description to clarify that fan control is not yet provided]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWfswbQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykvEwCfXU1MuYFQGgMdDmAZXEc+xFXZvqgAoKEcHDNA
6dVh26uchcEQLN/XqUDt
=x306
-----END PGP SIGNATURE-----
Merge tag 'spdx_identifiers-4.14-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull initial SPDX identifiers from Greg KH:
"License cleanup: add SPDX license identifiers to some files
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the
'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally
binding shorthand, which can be used instead of the full boiler plate
text.
This patch is based on work done by Thomas Gleixner and Kate Stewart
and Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset
of the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to
license had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied
to a file was done in a spreadsheet of side by side results from of
the output of two independent scanners (ScanCode & Windriver)
producing SPDX tag:value files created by Philippe Ombredanne.
Philippe prepared the base worksheet, and did an initial spot review
of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537
files assessed. Kate Stewart did a file by file comparison of the
scanner results in the spreadsheet to determine which SPDX license
identifier(s) to be applied to the file. She confirmed any
determination that was not immediately clear with lawyers working with
the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained
>5 lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that
was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that
became the concluded license(s).
- when there was disagreement between the two scanners (one detected
a license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply
(and which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases,
confirmation by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights.
The Windriver scanner is based on an older version of FOSSology in
part, so they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot
checks in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect
the correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial
patch version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch
license was not GPL-2.0 WITH Linux-syscall-note to ensure that the
applied SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'spdx_identifiers-4.14-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
License cleanup: add SPDX license identifier to uapi header files with a license
License cleanup: add SPDX license identifier to uapi header files with no license
License cleanup: add SPDX GPL-2.0 license identifier to files with no license
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch removes the un-necessary ifdef CONFIG_ACPI and directly
uses the acpi_match_table from the driver pdev.
Signed-off-by: Hoan Tran <hotran@apm.com>
[groeck: Dropped unnecessary initialization]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
We intended to test for failure here but accidentally tested for
success. It means that we don't set "*val" to true and it means that
if i2c_smbus_write_byte() does fail then we return success.
Fixes: e7895864b0d7 ("hwmon: (max6621) Add support for Maxim MAX6621 temperature sensor")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The setting of newval to zero is redundant as the following if/else
stanzas will always update newval to a new value. Remove the
redundant setting, cleans up clang build warning:
drivers/hwmon/asc7621.c:582:2: warning: Value stored to 'newval' is
never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This patch supports xgene-hwmon v2 which uses the non-cachable memory
as the PCC shared memory.
Signed-off-by: Hoan Tran <hotran@apm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
A previous commit changed the argument list of gpio_fan_get_of_data(),
removing the "struct *dev" argument and retrieving it instead from the
gpio_fan_data structure. The "dev" entry of gpio_fan_data was then
dereferenced to access the of_node field, leading to a kernel panic
during the probe as the "dev" entry of the gpio_fan_data structure was
not filled yet.
Fix this by setting fan_data->dev before calling gpio_fan_get_of_data().
Fixes: 5859d8d30737 ("hwmon: (gpio-fan) Get rid of platform data struct")
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This converts the GPIO fan driver to use GPIO descriptors. This way
we avoid indirection since the gpiolib anyway just use descriptors
inside, and we also get rid of explicit polarity handling: the
descriptors internally knows if the line is active high or active
low.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[groeck: Line length]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The "ctrl" and "num_ctrl" entries in the state container struct is
ambiguously named "ctrl" and "num_ctrl" overlapping with some hwmon
lingo and making it hard to understand. Since this array actually
contains the GPIO line numbers, from the Linux global GPIO numberspace,
used to control the different fan speeds. Rename these fields to
"gpios" (pluralis) and "num_gpios" so as to make it unambiguous.
Convert some instances of "unsigned" to "unsigned int" to keep
checkpatch happy.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
There is no point in storing the GPIO alarm settings in their
own struct so merge this into the main state container.
Convert the variables from "unsigned" to "unsigned int" to
make checkpatch happy.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
We are not passing the platform data struct into the driver from the
outside, there is no point of having it around separately so instead
of first populating the platform data struct and assigning the result
into the same variables in the state container (struct gpio_fan_data)
just assign the configuration from the device tree directly into the
state container members.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
We have no users of platform data, we made platform data driver-local,
so cut all #ifdefs for the platform data case, and depend on the
Kconfig CONFIG_OF_GPIO symbol.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The driver is storing the struct platform_device *pdev pointer
but what it is really using and want to pass around is a
struct device *dev pointer.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
There is not a single user of the platform data header in
<linux/gpio-fan.h>. We can conclude that all current users are
probing from the device tree, so start simplifying the code by
pulling the header into the driver.
Convert "unsigned" to "unsigned int" in the process to make
checkpatch happy.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Create local struct device *dev and device_node *np pointers to
make the code easier to read.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
MAX6621 is a PECI-to-I2C translator provides an efficient, low-cost
solution for PECI-to-SMBus/I2C protocol conversion. It allows reading the
temperature from the PECI-compliant host directly from up to four
PECI-enabled CPUs.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Don't populate const array watchdog_minors on the stack, instead make it
static. Makes the object code smaller by over 350 bytes:
Before:
text data bss dec hex filename
48019 38144 256 86419 15193 drivers/hwmon/w83793.o
After:
text data bss dec hex filename
47574 38232 256 86062 1502e drivers/hwmon/w83793.o
(gcc 6.3.0, x86-64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The previous value reduced the time required to determine
the fan value, however, it's also used as the final timeout
mechanism. The prevous value would work for any fan speed
greater than around 3k RPM. This increased value, lets the fan
speeds return quickly but will wait longer to handle speeds below 3k
RPM.
Testing: this value was determined through experimentation on the ast2400
on the Quanta-q71l. This configurations runs 8 fans attached to the
controller.
Signed-off-by: Patrick Venture <venture@google.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add new device tree binding for max1619.
Signed-off-by: Alan Tull <atull@kernel.org>
Cc: Jean Delvare <jdelvare@suse.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
A previous commit removed bit or'ing into to the integer status
so now status is now always zero. This means that the non-zero check on
status and the sht15_send_status call will never occur; it is deadcode.
Clean this up by removing the dead code.
Detected by: CoverityScan CID#1456835 ("Logically dead code")
Fixes: aa7ab80c578c ("hwmon: (sht15) Root out platform data")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
After finding out there are active users of this sensor I noticed:
- It has a single PXA27x board file using the platform data
- The platform data is only used to carry two GPIO pins, all other
fields are unused
- The driver does not use GPIO descriptors but the legacy GPIO
API
I saw we can swiftly fix this by:
- Killing off the platform data entirely
- Define a GPIO descriptor lookup table in the board file
- Use the standard devm_gpiod_get() to grab the GPIO descriptors
from either the device tree or the board file table.
This compiles, but needs testing.
Cc: arm@kernel.org
Cc: Marco Franchi <marco.franchi@nxp.com>
Cc: Davide Hug <d@videhug.ch>
Cc: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Marco Franchi <marco.franchi@nxp.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for handling temperature offset values for various AMD CPUs,
similar to the code used in the coretemp driver for Intel CPUs. This is
primarily for Ryzen CPUs (which has documented temperature offsets),
but the code is kept generic to simplify adding additional CPUs.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Introduce a local data structure and determine the temperature read
function at probe time to reduce runtime complexity.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Function snprintf already cares for the terminating NUL at the end of
the string, the caller doesn't need to do it.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Andrea Merello <andrea.merello@gmail.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The pmbus core may call read/write word data functions with a page value
of -1, intending to perform the operation without setting the page.
However, the read/write word data functions accept only unsigned 8-bit
page numbers, and therefore cannot check for negative page number to
avoid setting the page. This results in setting the page number to 0xFF.
This may result in errors or undefined behavior of some devices
(specifically the ir35221, which allows the page to be set to 0xFF,
but some subsequent operations to read registers may fail).
Switch the pmbus_set_page page parameter to an integer and perform the
check for negative page there. Make read/write functions consistent in
accepting an integer page number parameter.
Signed-off-by: Edward A. James <eajames@us.ibm.com>
Fixes: cbcdec6202 ("hwmon: (pmbus): Access word data for STATUS_WORD")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Commit 3d8f7a89a1 ("hwmon: (tmp102) Improve handling of initial read
delay") reduced the initial temperature read delay and made it dependent
on the chip's shutdown mode. If the chip was not in shutdown mode at probe,
the read delay no longer applies.
This ignores the fact that the chip initialization changes the temperature
sensor resolution, and that the temperature register values change when
the resolution is changed. As a result, the reported temperature is twice
as high as the real temperature until the first temperature conversion
after the configuration change is complete. This can result in unexpected
behavior and, worst case, in a system shutdown. To fix the problem,
let's just always wait for a conversion to complete before reporting
a temperature.
Fixes: 3d8f7a89a1 ("hwmon: (tmp102) Improve handling of initial read delay")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=197167
Reported-by: Ralf Goebel <ralf.goebel@imago-technologies.com>
Cc: Ralf Goebel <ralf.goebel@imago-technologies.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The TSI channel, which is usually used for touchscreen support, but can
be used as 4 general purpose ADCs. When used as a touchscreen interface
the touchscreen driver switches the device into 1ms sampling mode (rather
than the default 10ms economy mode) as recommended by the manufacturer.
When using the TSI channels as a general purpose ADC we are currently not
doing this and testing suggests that this can result in ADC timeouts:
[ 5827.198289] da9052 spi2.0: timeout waiting for ADC conversion interrupt
[ 5827.728293] da9052 spi2.0: timeout waiting for ADC conversion interrupt
[ 5993.808335] da9052 spi2.0: timeout waiting for ADC conversion interrupt
[ 5994.328441] da9052 spi2.0: timeout waiting for ADC conversion interrupt
[ 5994.848291] da9052 spi2.0: timeout waiting for ADC conversion interrupt
Switching to the 1ms timing resolves this issue.
Fixes: 4f16cab19a ("hwmon: da9052: Add support for TSI channel")
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Acked-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Commit 2ca492e22c has moved the call to 'kfifo_alloc()' from after the
main 'if' statement to before it.
But it has not updated the error handling paths accordingly.
Fix all that:
- if 'kfifo_alloc()' fails we can return directly
- direct returns after 'kfifo_alloc()' must now go to 'out_mbox_free'
- 'goto out_mbox_free' must be replaced by 'goto out', otherwise the
'[pcc_]mbox_free_channel()' call will be missed.
Fixes: 2ca492e22c ("hwmon: (xgene) Fix crash when alarm occurs before driver probe")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
... and __initconst if applicable.
Based on similar work for an older kernel in the Grsecurity patch.
[JD: fix toshiba-wmi build]
[JD: add htcpen]
[JD: move __initconst where checkscript wants it]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Add the lantiq cpu temperature sensor support for xrx200.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Guenter Roeck