DBGU means Debug Unit, was refered as "DGBU" in some files. Fixed to "DBGU".
Signed-off-by: Samuel R. C. Vale <srcvale@holoscopio.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Board code was wrongly setting up the reset pin for AC97 on at91sam9263ek.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch modifies the support of AC97 on the at91sam9263 ek board, so it would
share the code with AVR32.
Plus it removes a typo in at91sam9263_devices.c.
Signed-off-by: Sedji Gaouaou <sedji.gaouaou@atmel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds board-specific data for IDE support on afeb9260.
Depends on #5631/1
Tested-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Acked-by: Sergey Lapin <slapin@ossfans.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds platform data for CF/IDE support
and SMC init code for AT91SAM9260 SoC.
Tested-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx:
dmaengine: at_hdmac: add DMA slave transfers
dmaengine: at_hdmac: new driver for the Atmel AHB DMA Controller
dmaengine: dmatest: correct thread_count while using multiple thread per channel
dmaengine: dmatest: add a maximum number of test iterations
drivers/dma: Remove unnecessary semicolons
drivers/dma/fsldma.c: Remove unnecessary semicolons
dmaengine: move HIGHMEM64G restriction to ASYNC_TX_DMA
fsldma: do not clear bandwidth control bits on the 83xx controller
fsldma: enable external start for the 83xx controller
fsldma: use PCI Read Multiple command
CPUAT91 is based on Atmel's AT91RM9200 with up to 16MB Strataflash,
up to 128MB SDRAM and an ethernet PHY in RMII mode.
Signed-off-by: Eric Benard <ebenard@eukrea.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
CPU9260 and CPU9G20 share the same PCB populated with either
Atmel's AT91SAM9260B or AT91SAM9G20B with up to 64MB Strataflash,
up to 128MB SDRAM, up to 2GB NAND and an ethernet PHY in RMII mode.
Signed-off-by: Eric Benard <eric@eukrea.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
It adds DMA peripheral identifiers for hardware handshaking interface. It will
be used in platform code.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch for at_hdmac adds the slave transfers capability to the Atmel DMA
controller available on some AT91 SOCs. This allow peripheral to memory and
memory to peripheral transfers with hardware handshaking.
Slave structure for controller specific information is passed through channel
private data. This at_dma_slave structure is defined in at_hdmac.h header file
and relative hardware definition are moved to this file from at_hdmac_regs.h.
Doing this we allow the channel configuration from platform definition code.
This work is intensively based on dw_dmac and several slave implementations.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This AHB DMA Controller (aka HDMA or DMAC on AT91 systems) is availlable on
at91sam9rl chip. It will be used on other products in the future.
This first release covers only the memory-to-memory tranfer type. This is the
only tranfer type supported by this chip. On other products, it will be used
also for peripheral DMA transfer (slave API support to come).
I used dmatest client without problem in different configurations to test it.
Full documentation for this controller can be found in the SAM9RL datasheet:
http://www.atmel.com/dyn/products/product_card.asp?part_id=4243
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The WM8731 driver has been updated to allow registration via normal
device model methods rather than from within the ASoC driver probe
so update the AT91SAM9G20-EK to make use of this.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
From: Hong Xu <hong.xu@atmel.com>
Here are the modification to at91sam9261 files dedicated to the support of
at91sam9g10. This direction has been adopted to minimize code duplication.
All at91sam9261 drivers are enabled in _devices and board- files. Modificaton
to peripherals that support at91sam9g10 will be added in future patches.
Signed-off-by: Hong Xu <hong.xu@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
From: Hong Xu <hong.xu@atmel.com>
AT91sam9g10 is an ARM 926ej-s SOC. It is an evolution of the at91sam9261 with a
faster clock speed: 266/133MHz.
Here is the basic header file support for this product.
Signed-off-by: Hong Xu <hong.xu@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
From: Hong Xu <hong.xu@atmel.com>
Add the at91sam9g10 support to the AT91 generic clock file. It takes
advantage of the management by functionalities of those PLLs and clocks.
Signed-off-by: Hong Xu <hong.xu@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This adds input keyboard gpio support on at91sam9g20ek board.
It adds button 3 and 4.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Here are the at91 specific files dedicated to the at91sam9g45 series. They
mimic the traditional at91 way of managing chips & boards.
The first board that embeds at91sam9g45 chip is the AT91SAM9G45-EKES. In
the future, the main board for this 9g45 series will be the
AT91SAM9M10G45-EK (I choose this last name for the board file).
Simple drivers are enabled in _devices and board- files. Newer peripheral
support will be added in future patches.
Incuded peripherals support (for now):
- USART
- SPI
- Ethernet
- NAND flash
- LCD
- gpio/joystick/buttons
- leds and pwm
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
AT91sam9g45 series is an ARM 926ej-s SOC family clocked at 400/133MHz.
It embedds USB high speed host and device, LCD, DDR2 RAM, and a full set of
peripherals.
Here is the basic header file support for this product series.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add the at91sam9g45 series support to the AT91 generic clock file.
This takes care of the particularities of the PMC for this series.
It also takes advantage of the management by functionalities of
those PLLs and clocks.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove at91_gpiolib_request. It returns -EPERM if a request pin is not
in GPIO mode, however we want to be able to gpio_request alternative
function pins to reserve them, and in some cases we need to be able to
use the gpiolib functions on alternative function pins.
Signed-off-by: Ryan Mallon <ryan@bluewatersys.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This adds input keyboard gpio support on at91sam9rlek board. It adds button 1
and 2 (left and right click).
It also adds gpio leds ds1, ds2 and ds3.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Here is a little update to the at91sam9rlek lcd interface.
This will correct the power pin of the LCD.
It will also add precision to the struct atmel_lcdfb_info
scructure: backlight enabling and wiring mode correction:
RGB wiring on the -EK board.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Proper pin configuration for MMC.
Signed-off-by: Sergey Lapin <slapin@ossfans.org>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add board information about on-board I2C eeprom AT24C512N at 0x50.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
ASoC driver for AT91SAM9260-based AFEB9260 board
Signed-off-by: Sergey Lapin <slapin@ossfans.org>
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In clock.c file the clock management is grouped by cpu with cpu_is_xxx()
function. This lead to some kind of difficulties to read this file and
maintainability issues as the number of AT91 cpus & PLLs/clocks is growing.
In this patch, I try to group clock functionality together and match cpus with
this functionality set.
An update to at91_pmc.h is needed to cover some new PMC possibilities (and
some update in comments).
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <avictor.za@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Pass clocksource pointer to the read() callback for clocksources. This
allows us to share the callback between multiple instances.
[hugh@veritas.com: fix powerpc build of clocksource pass clocksource mods]
[akpm@linux-foundation.org: cleanup]
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Acked-by: John Stultz <johnstul@us.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The flexible array in the USBH platform data is not safe to copy. The
compiler will not allocate any extra memory for the non-init platform
data structure (in the *_devices.c files) since it isn't given any
defaults at compile time. When the probe function attempts to address
that array, it will actually attempt to access data in an adjacent
structure.
Since there are currently no (known) implementations of the at91 USBH
IP with more than 2 vbus pins, I am capping the value at 2. If somebody
tries to assign more, then the compiler will produce a warning.
Signed-off-by: Justin Waters <justin.waters@timesys.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Change pr_debug to pr_err on error paths in the AT91 power management
code. All of the errors will result in the cpu not going into the
suspend state. This patch makes it possible to identify problems with
suspend when power management debugging is not enabled.
Signed-off-by: Ryan Mallon <ryan@bluewatersys.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
OMAP wishes to pass state to the boot loader upon reboot in order to
instruct it whether to wait for USB-based reflashing or not. There is
already a facility to do this via the reboot() syscall, except we ignore
the string passed to machine_restart().
This patch fixes things to pass this string to arch_reset(). This means
that we keep the reboot mode limited to telling the kernel _how_ to
perform the reboot which should be independent of what we request the
boot loader to do.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Cc: Andrew Victor <avictor.za@gmail.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This is IDE host driver for AT91 (SAM9, CAP9, AT572D940HF) Static Memory
Controller with Compact Flash True IDE Mode logic.
Driver have to switch 8/16 bit bus width when accessing Task Tile or Data
Register. Moreover some extra things need to be done when setting PIO mode.
Only PIO mode is used, hardware have no DMA support. If interrupt line is
connected through GPIO extra quirk is needed to cope with fake interrupts.
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Cc: Andrew Victor <avictor.za@gmail.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
We've discovered that our AT91SAM9260 board consumed too much power when
returning from a slowclock low-power mode. RAM self-refresh is enabled in
a bootloader in our case, this is how we saw a difference. Estimated ca.
30mA more on 4V battery than the same state before powersaving.
After a small research we found that there seems to be a bogus
sdram_selfrefresh_disable() call at the end of at91_pm_enter() call, which
overwrites the LPR register with uninitialized value. Please find the
suggested patch attached.
This patch fixes correct restoring of LPR register of the Atmel AT91 SDRAM
controller when returning from a power saving mode.
Signed-off-by: Andrei Birjukov <andrei.birjukov@artecdesign.ee>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The AT91SAM20-EK has a WM8731 attached to it with MCLK supplied from
PCLK0 and the digital audio interface supplied by SSC0.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for inverted rdy_busy pin for Atmel nand device controller
It will fix building error on NeoCore926 board.
Acked-by: Andrew Victor <linux@maxim.org.za>
Acked-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Gregory CLEMENT <gclement@adeneo.adetelgroup.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Enable the GPIO clocks earlier in the initialization sequence. This
allow the board-setup code to read and set GPIO pins.
Signed-off-by: Marc Pignat <marc.pignat@hevs.ch>
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The recently merged AT91SAM9 watchdog driver uses the
AT91SAM9X_WATCHDOG config variable, whereas the original version of
the driver (and the platform support code) used AT91SAM9_WATCHDOG.
This causes the watchdog platform_device to never be registered, and
therefore the driver not to be initialized.
This patch:
- updates the platform support code to use AT91SAM9X_WATCHDOG.
- includes <linux/io.h> to fix compile error (same fix as was applied
to at91rm9200_wdt.c)
- fixes comment regarding watchdog clock-rates in at91rm9200.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for gpiolib, including debugfs output, to the AT91 family.
The at91_get/set_gpio_value calls still exist since they are used by the
atmel serial driver.
Signed-off-by: Ryan Mallon <ryan@bluewatersys.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
arch/arm/mach-at91/at91cap9.c:337: error: 'NR_AIC_IRQS' undeclared here (not in a function)
arch/arm/mach-at91/at91rm9200.c:301: error: 'NR_AIC_IRQS' undeclared here (not in a function)
arch/arm/mach-at91/at91sam9260.c:351: error: 'NR_AIC_IRQS' undeclared here (not in a function)
arch/arm/mach-at91/at91sam9261.c:287: error: 'NR_AIC_IRQS' undeclared here (not in a function)
arch/arm/mach-at91/at91sam9263.c:312: error: 'NR_AIC_IRQS' undeclared here (not in a function)
arch/arm/mach-at91/at91sam9rl.c:304: error: 'NR_AIC_IRQS' undeclared here (not in a function)
arch/arm/mach-h720x/h7202-eval.c:38: error: implicit declaration of function 'IRQ_CHAINED_GPIOB'
arch/arm/mach-ks8695/devices.c:46: error: 'KS8695_IRQ_WAN_RX_STATUS' undeclared here (not in a function)
arch/arm/mach-msm/devices.c:28: error: 'INT_UART1' undeclared here (not in a function)
arch/arm/mach-mx2/devices.c:233: error: 'MXC_GPIO_IRQ_START' undeclared here (not in a function)
arch/arm/mach-mx3/devices.c:128: error: 'MXC_GPIO_IRQ_START' undeclared here (not in a function)
arch/arm/mach-omap1/mcbsp.c:140: error: 'INT_730_McBSP1RX' undeclared here (not in a function)
arch/arm/mach-omap1/mcbsp.c:165: error: 'INT_McBSP1RX' undeclared here (not in a function)
arch/arm/mach-omap1/mcbsp.c:200: error: 'INT_McBSP1RX' undeclared here (not in a function)
arch/arm/mach-omap2/board-apollon.c:286: error: implicit declaration of function 'omap_set_gpio_direction'
arch/arm/mach-omap2/mcbsp.c:154: error: 'INT_24XX_MCBSP1_IRQ_RX' undeclared here (not in a function)
arch/arm/mach-omap2/mcbsp.c:181: error: 'INT_24XX_MCBSP1_IRQ_RX' undeclared here (not in a function)
arch/arm/mach-pxa/e350.c:36: error: 'IRQ_BOARD_START' undeclared here (not in a function)
arch/arm/plat-s3c/dev-i2c0.c:32: error: 'IRQ_IIC' undeclared here (not in a function)
...
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'cpus4096-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (66 commits)
x86: export vector_used_by_percpu_irq
x86: use logical apicid in x2apic_cluster's x2apic_cpu_mask_to_apicid_and()
sched: nominate preferred wakeup cpu, fix
x86: fix lguest used_vectors breakage, -v2
x86: fix warning in arch/x86/kernel/io_apic.c
sched: fix warning in kernel/sched.c
sched: move test_sd_parent() to an SMP section of sched.h
sched: add SD_BALANCE_NEWIDLE at MC and CPU level for sched_mc>0
sched: activate active load balancing in new idle cpus
sched: bias task wakeups to preferred semi-idle packages
sched: nominate preferred wakeup cpu
sched: favour lower logical cpu number for sched_mc balance
sched: framework for sched_mc/smt_power_savings=N
sched: convert BALANCE_FOR_xx_POWER to inline functions
x86: use possible_cpus=NUM to extend the possible cpus allowed
x86: fix cpu_mask_to_apicid_and to include cpu_online_mask
x86: update io_apic.c to the new cpumask code
x86: Introduce topology_core_cpumask()/topology_thread_cpumask()
x86: xen: use smp_call_function_many()
x86: use work_on_cpu in x86/kernel/cpu/mcheck/mce_amd_64.c
...
Fixed up trivial conflict in kernel/time/tick-sched.c manually
Impact: change calling convention of existing clock_event APIs
struct clock_event_timer's cpumask field gets changed to take pointer,
as does the ->broadcast function.
Another single-patch change. For safety, we BUG_ON() in
clockevents_register_device() if it's not set.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Ingo Molnar <mingo@elte.hu>
Thomas claims that irqs are disabled when set_next_event is called. But
David and Remy claim they saw irqs being enabled here. As both sides
don't seem to have time to investigate here, start with a warning that
might trigger if the problem still exists.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-By: David Brownell <dbrownell@users.sourceforge.net>
Cc: Bill Gatliff <bgat@billgatliff.com>
Acked-By: Remy Bohmer <linux@bohmer.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
The AT91CAP9 revC CPU has a few differences over the previous,
revB CPU which was distributed in small quantities only (revA was
an internal Atmel product only).
This patch adds the detection routines to recognize the different
AT91CAP9 revisions (based on the PMC subsystem version number), and
uses them to:
- activate a workaround for the external interrupts levels
(on revB CPUs)
- set the UDPHS_BYPASS bit (on revB CPUs)
- set AT91_GPBR register address to the correct offset
(0xfffffd50 on revB, 0xfffffd60 on revC)
For debugging usage, the CPU revision can be found in /proc/cpuinfo
on the 'Revision' line.
This patch is extracted from Andrew Victor's -at91 patch (2.6.27-at91.patch)
where it has been tested for the last 6 months.
Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for the Adeneo NeoCore 926 board.
Signed-off-by: Guillaume GARDET <guillaume.gardet@free.fr>
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert the SAM9 and CAP9 board-specific files to make use of the
sam9_smc_configure() method to configure the memory-controller for
external peripherals.
The following boards have been modified:
cam60 : NAND
cap9adk : NAND, NOR
qil-a9260 : NAND
sam9-l9260 : NAND
sam9260ek : NAND
sam9261ek : DM9000 Ethernet, NAND
sam9263 : NAND
sam9g20ek : NAND
sam9rlek : NAND
usb-a9260 : NAND
usb-a9263 .: NAND
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In at91_add_device_nand(), do not configure the Static Memory
controller with specific timing values.
The *_devices.c files are board independent, and the SMC timing values
are specific to the NAND devices that are installed on the board.
The board-specific files are now responsible for configuring the
Static Memory controller (if the don't want to leave it up to a
bootloader).
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add a structure 'sam9_smc_config' and function sam9_smc_configure() to
allow the board-specific files to specify the configuration of the
Static Memory Controller per chip-select. This allows the board file
to specify timings for NAND flash, NOR flash or other external
peripherals.
This functionality can be used for all the SAM9 and CAP9 processors.
(the AT91RM9200 has a different memory-controller)
This patch is based on similar code in the AVR32 architecture.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As Al did for Versatile in 2ad4f86b60,
add a typesafe __io implementation for platforms to use. Convert
platforms to use this new simple typesafe implementation.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When ISA_DMA_API is unset, we're not implementing the ISA DMA API,
so there's no point in publishing the prototypes via asm/dma.h, nor
including the machine dependent parts of that API.
This allows us to remove a lot of mach/dma.h files which don't contain
any useful code. Unfortunately though, some platforms put their own
private non-ISA definitions into mach/dma.h, so we leave these behind
and fix the appropriate #include statments.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Let's provide an overridable default instead of having every machine
class define __virt_to_bus and __bus_to_virt to the same thing. What
most platforms are using is bus_addr == phys_addr so such is the default.
One exception is ebsa110 which has no DMA what so ever, so the actual
definition is not important except only for proper compilation. Also
added a comment about the special footbridge bus translation.
Let's also remove comments alluding to set_dma_addr which is not
(and should not) be commonly used.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rather than:
config CPU_BLAH
bool
depends on ARCH_FOO || MACH_BAR
default y if ARCH_FOO || MACH_BAR
arrange for ARCH_FOO and MACH_BAR to select CPU_BLAH directly.
Acked-by: Nicolas Pitre <nico@marvell.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Acked-by: Brian Swetland <swetland@google.com>
Acked-by: Eric Miao <eric.miao@marvell.com>
Acked-by: Nicolas Bellido <ml@acolin.be>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
i2c_board_info array was filled incorrectly.
Due to circumstances, the way it is filled works.
This patch fills array properly.
Signed-off-by: Sergey Lapin <slapin@ossfans.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
According to the documentation gpio_free should only be called from task
context only. To make this more explicit add a might sleep to all
implementations.
This patch changes the gpio_free implementations for the arm architecture.
DaVinci is skipped on purpose to simplify the merge process for patches
switching it over to use gpiolib as per request by David Brownell.
Signed-off-by: Uwe Kleine-König <ukleinek@informatik.uni-freiburg.de>
Cc: David Brownell <david-b@pacbell.net>
Cc: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
From: David Brownell <dbrownell@users.sourceforge.net>
The "5298/1: Drop desc_handle_irq()" patch went overboard
and deleted an essential line of code, causing all AT91
GPIO interrupts to oops (in irq). Trimmed example:
Unable to handle kernel NULL pointer dereference at virtual address 000000c4
...
PC is at gpio_irq_handler+0x78/0xd0
LR is at gpio_irq_handler+0x38/0xd0
...
Backtrace:
[<c0029884>] (gpio_irq_handler+0x0/0xd0) from [<c0020054>] (__exception_text_start+0x54/0x7c)
[<c0020000>] (__exception_text_start+0x0/0x7c) from [<c00209ec>] (__irq_svc+0x2c/0x60)
Exception stack(0xc1c1de00 to 0xc1c1de48)
[<c01f4ca8>] (_spin_unlock_irq+0x0/0x3c) from [<c01389f8>] (at91ether_open+0x220/0x318)
[<c01387d8>] (at91ether_open+0x0/0x318) from [<c018caa4>] (dev_open+0xa8/0x10c)
[<c018c9fc>] (dev_open+0x0/0x10c) from [<c018b874>] (dev_change_flags+0x98/0x164)
[<c018b7dc>] (dev_change_flags+0x0/0x164) from [<c0019f8c>] (ip_auto_config+0x164/0xe28)
[<c0019e28>] (ip_auto_config+0x0/0xe28) from [<c0020318>] (__exception_text_end+0x60/0x180)
[<c00202b8>] (__exception_text_end+0x0/0x180) from [<c0008738>] (kernel_init+0x70/0xd8)
[<c00086c8>] (kernel_init+0x0/0xd8) from [<c00398e0>] (do_exit+0x0/0x6ac)
This patch restores the missing line'o'code.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
desc_handle_irq() was declared as obsolete since long ago.
Replace it with generic_handle_irq()
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The name of the platform device 'at91_pwm_leds' conflicts with the
function at91_pwm_leds().
So rename the device 'at91_pwm_leds_device' to be more specific.
Similarly rename 'at91_gpio_leds_device' for consistency.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for the LEDs on the Conitec ARM&EVA board.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add copyright information for some of the AT91 header files.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds support for a low(er)-power suspend-to-RAM.
In addition to the SDRAM being put into self-refresh mode, the Master
Clock is set to the Slow-clock rate (32Khz) and PLLA & PLLB are
disabled.
Certain peripherals are therefore also disabled, and thus cannot be
used as wakeup sources.
This patch has been included in the AT91 patches in various forms
since 2.6.19 and a number of people have worked or commented on it,
most notably:
Savin Zlobec (for the original AT91RM9200 support)
Anti Sullin (for the SAM9260 version)
David Brownell, etc.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Allow the various GPIO-connected buttons to be used as wakeup sources.
Also enable the internal GPIO pullup.
Signed-off-by: Sedji Gaouaou <sedji.gaouaou@atmel.com>
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support or the GPIO-connected buttons on the Atmel AT91SAM9260-EK board.
Signed-off-by: Sedji Gaouaou <sedji.gaouaou@atmel.com>
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds initialization of the Touchscreen controller for the
AT91SAM9RL processor.
Signed-off-by: Justin Waters <justin.waters@timesys.com>
Signed-off-by: Dan Liang <dan.liang@atmel.com>
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Use the PWM controller and leds-atmel-pwm.c driver to drive a LED on
the Atmel AT91SAM9263-EK board.
Signed-off-by: Sedji Gaouaou <sedji.gaouaou@atmel.com>
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add platform_devices and configuration of the PWM controller found on
Atmel AT91CAP9, SAM9263 and SAM9RL processors.
SAM9263 support by Sedji Gaouaou.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In the various AT91 board files, replace hard-coded size values (eg,
0x800000) with the SZ_ size definitions (eg, SZ_8M) from sizes.h
Also replace MTD partition offsets with MTDPART_OFS_NXTBLK.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The at91sam9260 and at91sam9263 EK boards have 64 KiB I2C EEPROMs.
This patch declares them in the board init code so the new at24
driver will use them.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
MACB ethernet support for AFEB9260
Depends on 5210/2
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Sergey Lapin <slapin@ossfans.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds support for AT91SAM9260-based board AFEB9260
which is a product from both Open Source design which runs
Open Source software. Some commertial projects
are made with this design. A board is basically AT91SAM9260-EK
with some modifications and different peripherals and different
parts used. Main purpose of this project is to gain experience in
hardware design.
More info: http://groups.google.com/group/arm9fpga-evolution-board
(In Russian only, sorry).
Subversion repository: svn://194.85.238.22/home/users/george/svn/arm9eb
By this patch only basic functionality is provided.
Signed-off-by: Sergey Lapin <slapin@ossfans.org>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove includes of asm/hardware.h in addition to asm/arch/hardware.h.
Then, since asm/hardware.h only exists to include asm/arch/hardware.h,
update everything to directly include asm/arch/hardware.h and remove
asm/hardware.h.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There are 43 includes of asm/mach-types.h by files that don't
reference anything from that file. Remove these unnecessary
includes.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Structs called at91_nand_data where renamed to atmel_nand_data
and configs called *MTD_NAND_AT91* where renamed to
*MTD_NAND_ATMEL*. This was unfortunately not done consistently,
causing NAND chips not being initialised on several ARM boards.
I am aware that the author of the original change did not rename
MTD_NAND_AT91_BUSWIDTH to MTD_NAND_ATMEL_BUSWIDTH, for example.
All *MTD_NAND_AT91* where renamed to *MTD_NAND_ATMEL* in order
to keep naming consistency.
This patch was only tested on a MACH_SAM9_L9260, as this is the
only ARM board I have to my disposal.
Before this patch:
$ git-ls-files |xargs grep atmel_nand |wc -l
105
$ git-ls-files |xargs grep at91_nand |wc -l
4
$ git-ls-files |xargs grep MTD_NAND_ATMEL |wc -l
8
$ git-ls-files |xargs grep MTD_NAND_AT91 |wc -l
47
After this patch:
$ git-ls-files |xargs grep atmel_nand |wc -l
109
$ git-ls-files |xargs grep at91_nand |wc -l
0
$ git-ls-files |xargs grep MTD_NAND_ATMEL |wc -l
55
$ git-ls-files |xargs grep MTD_NAND_AT91 |wc -l
0
Signed-off-by: Pieter du Preez <pdupreez@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
struct at91_nand has been renamed atmel_nand. Fix the four boards that
were added since the patch was created.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
IRQT_* and __IRQT_* were obsoleted long ago by patch [3692/1].
Remove them completely. Sed script for the reference:
s/__IRQT_RISEDGE/IRQ_TYPE_EDGE_RISING/g
s/__IRQT_FALEDGE/IRQ_TYPE_EDGE_FALLING/g
s/__IRQT_LOWLVL/IRQ_TYPE_LEVEL_LOW/g
s/__IRQT_HIGHLVL/IRQ_TYPE_LEVEL_HIGH/g
s/IRQT_RISING/IRQ_TYPE_EDGE_RISING/g
s/IRQT_FALLING/IRQ_TYPE_EDGE_FALLING/g
s/IRQT_BOTHEDGE/IRQ_TYPE_EDGE_BOTH/g
s/IRQT_LOW/IRQ_TYPE_LEVEL_LOW/g
s/IRQT_HIGH/IRQ_TYPE_LEVEL_HIGH/g
s/IRQT_PROBE/IRQ_TYPE_PROBE/g
s/IRQT_NOEDGE/IRQ_TYPE_NONE/g
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Xose Vazquez Perez points out that this file should not be marked
executable.
Reported-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Support for the at91sam9g20 : Atmel 400Mhz ARM 926ej-s SOC.
AT91sam9g20 is an evolution of the at91sam9260 with a faster clock
speed.
We created a new board for this device but based the chip support
directly on 9260 files with little updates.
Here is the chip page on Atmel wabsite:
http://atmel.com/dyn/products/product_card.asp?part_id=4337
Signed-off-by: Sedji Gaouaou <sedji.gaouaou@atmel.com>
Signed-off-by: Justin Waters <justin.waters@timesys.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
New timings are based on application note
"NAND Flash Support on AT91SAM9 Microcontrollers" available at
http://atmel.com/dyn/resources/prod_documents/doc6255.pdf).
Signed-off-by: Patrice Vilchez <patrice.vilchez@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This is basically s/at91_nand/atmel_nand/g with some manual inspection.
Signed-off-by: Håvard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Adds support for the USB High Speed Device Port on the AT91SAM9RL
system on chip. The AT91SAM9RL uses the same UDPHS IP as the AVR32 and
the AT91CAP9 (atmel_usba_udc driver).
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This is patch 2 of 2 adding support for the USB High Speed Device Port
on the AT91CAP9 system on chip. The AT91CAP9 uses the same UDPHS IP
as the AVR32 and the AT91SAM9RL.
This patch declares the UDPHS ressources in the at91cap9 (cpu and
adk board) files, wires up the atmel_usba_udc driver to them,
and activates the driver in the defconfig.
Signed-off-by: Stelian Pop <stelian@popies.net>
Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This is patch 1 of 2 adding support for the USB High Speed Device Port
on the AT91CAP9 system on chip. The AT91CAP9 uses the same UDPHS IP
as the AVR32 and the AT91SAM9RL.
This patch makes the generic AT91 adaptations, mainly dealing with
the addition of the UDPHS UTMI clock.
Signed-off-by: Stelian Pop <stelian@popies.net>
Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert the following AT91RM9200-based boards to the new-style UART
initialization:
- Conitec ARM&EVA
- Atmel AT91RM9200-DK
- Embest ATEB9200
- Atmel AT91RM9200-EK
- KwikByte KB920x
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for three AT91-based boards available from Calao Systems:
USB_A9260, USB_A9263 and QIL_A9260.
Signed-off-by: Grégory Hermant <gregory.hermant@calao-systems.com>
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cleanup the YL9200 board-support file.
Other things fixed are:
- Use new-style UART initialization
- Register all LEDs as gpio_leds.
- NOR Flash error noted in comments fixed by increasing YL9200_FLASH_SIZE
- The only I2C device is the AT24C eeprom.
- Setup of NWAIT pin and programming of SMC controller for the LCD/VGA.
- Configure touchscreen interrupt pin.
Also adding the board to the KConfig and Makefile.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Export the AT91 clock functions for the AT91X40. Some external code common
to all AT91 family parts relys on this, like the gpio and serial support.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix initialization of framebuffer not calling ioremap_writecombine() function
and not using internal SRAM for at91sam9rl.
This is a little rework of the "Don't initialize a pre-allocated framebuffer"
patch that corrects the call to ioremap_writecombine() function.
It also cuts the use of internal SRAM for at91sam9rl : it is a bit small
for a framebuffer.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Andrew Victor <linux@maxim.org.za>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Based on earlier work by Jon Smirl and Jochen Friedrich.
Update most new-style i2c drivers to use standard module aliasing
instead of the old driver_name/type driver matching scheme. I've
left the video drivers apart (except for SoC camera drivers) as
they're a bit more diffcult to deal with, they'll have their own
patch later.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Jon Smirl <jonsmirl@gmail.com>
Cc: Jochen Friedrich <jochen@scram.de>
Build fix for power management on at91sam9263: it has two memory
controllers instead of just one, so it might have two banks of
DRAM to put into selfrefresh mode. For now we continue to assume
only the first bank is populated.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
typo in mci configuration in devices files
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
If the user specified a fixed framebuffer address on the command line, it may
have been initialized already with a splash image or something, so we
shouldn't clear it.
Therefore, we should only initialize the framebuffer if we allocated it
ourselves. This patch also updates the AVR32 setup code to clear the
framebuffer if it allocated it itself, i.e. the user didn't provide a fixed
address or the reservation failed.
I've updated the at91 platform code as well so that it initializes the
framebuffer if it is located in SRAM, but I haven't tested that it actually
works.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Nicolas FERRE <nicolas.ferre@rfo.atmel.com>
Cc: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
None of these files use any of the functionality promised by
asm/semaphore.h. It's possible that they rely on it dragging in some
unrelated header file, but I can't build all these files, so we'll have
fix any build failures as they come up.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Update AT91SAM9/CAP9 PIT driver to use generic time and clockevent
infrastructure:
- Clocksource gives sub-microsecond timestamp precision, assuming
memory is clocked at over 16 MHz. It's less than a 32 bit counter,
unless it's is also generating IRQs.
- Clockevent device supports periodic mode only; no oneshot
support from this hardware. No IRQs generated unless it's the
active clocksource.
Later, another timer (probably from a TC module) can provide a oneshot
clockevent device to get NO_HZ and High-Res-Timer behavior.
This also updates the timekeeping to use the actual master clock rate
on the system, instead of compile-time <asm/arch/timex.h> constants
matching what Atmel's EK boards use. (Product boards may well differ!)
Plus cleanup: rename "*_timer*" symbols to "*_pit*" (there are other
timers, but only one PIT); shorter lines; remove needless CPP stuff;
make several symbols static; etc.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
All the SAM9 boards supported by mainline and the AT91 patches have
been converted to the new-style UART initialization. Therefore drop
support for the old at91_init_serial() interface for SAM9.
at91_uarts[] array can also be marked as __initdata.
The warning that no serial-console is defined moved from
at91_set_serial_console() to at91_add_device_serial() since the whole
point is the board-specific file is not calling
at91_set_serial_console().
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Support for the emQbit ECB_AT91 board.
<http://wiki.emqbit.com/free-ecb-at91>
Original patch from Nelson Castillo.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Support for the Olimex SAM9-L9260 board.
<http://www.olimex.com/dev/sam9-L9260.html>
Original patch from Ivan Vasilev.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Support for the Kwikbyte KB9260 (CAM60) board.
<http://www.kwikbyte.com/KB9260.html>
Original patch from Kwikbyte.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Converts the D1/PB2 LED to use the gpio-leds API and heartbeat trigger.
Signed-off-by: Bill Gatliff <bgat@billgatliff.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Converts the CSB637 to the new-style UART initialization API.
Signed-off-by: Bill Gatliff <bgat@billgatliff.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Converts the CSB337 target to the new UART initialization API.
Signed-off-by: Bill Gatliff <bgat@billgatliff.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for the GPIO-driven LEDs (using NEW_LEDS) on the Atmel
SAM9260-EK and SAM9261-EK boards.
Signed-off-by: Sedji Gaouaou <sedji.gaouaou@atmel.com>
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for AT73C213 audio DAC on the Atmel SAM9260-EK and
SAM9261-EK boards.
Signed-off-by: Sedji Gaouaou <sedji.gaouaou@atmel.com>
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Register platform_devices for the Timer/Counter Block peripherals
found on the AT91RM9200, SAM9 & CAP9 processors.
Original patch from David Brownell.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The RTT-as-RTC driver will search for the user-specified RTT
peripheral via ID number (0 .. 1).
Therefore if the processor only contains a single RTT peripheral, we
need to set its platform_device.id to "0" instead of "-1".
Also add the missing platform_device resource for the CAP9 processor.
Bug reported by Sedji Gaouaou.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The Reset controller on the SAM9/CAP9 processors will store the reason
for the last system reset.
On startup, display this information (wakeup signal, RTT alarm,
watchdog reset, user reset, etc)
Based on patch from David Brownell.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Basic power-management (suspend-to-ram) support for Atmel SAM9 and
CAP9 processors.
Based on comments & patches from Anti Sullin and David Brownell.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert the Atmel SAM9260-EK, SAM9261-EK, SAM9263-EK and SAM9RL-EK
boards to use the new-style UART initialization.
Signed-off-by: Sedji Gaouaou <sedji.gaouaou@atmel.com>
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
On AT91 processors that include an ECC controller, pass its base
address to the NAND driver via platform_device resources.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Enable system shutdown/power-off on AT91SAM9 and AT91CAP9 based boards.
This does not require power-management to be enabled, and the
pm_power_off method can be overridden in board-specific files if
necessary.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The AT91CAP9 processor includes the same Static Memory Controller
(SMC) peripheral as the SAM9 processors, but replaces the SDRAM
Controller with a DDR/SDR Controller (DDRSDRC).
This patch splits the existing
include/asm-arm/arch-at91/at91sam926x_mc.h into at91sam9_sdramc.h and
at91sam9_smc.h.
It also adds an at91cap9_ddrsdr.h for the DDRSDRC controller.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
1. Configuration file for YL9200
2. Board file fro YL9200
Adds support for the UCdragon YL9200 board available widly in China
Signed-off-by: steve birtles <arm_kernel_development@micromark.net.cn>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Correct GPIO pin assignment for the LCD power control (PCI)
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove false lockdep warnings about lock recursion when declaring
IRQs as being wake-capable, by marking putting GPIO irq_desc locks
into their own class.
(Thanks to Peter Zijlstra for helping track down such a small
fix to this problem.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix section warning:
WARNING: arch/arm/mach-at91/built-in.o(.text+0xd74): Section mismatch in reference
from the function init_programmable_clock()
to the function .init.text:at91_css_to_clk()
The function init_programmable_clock() references
the function __init at91_css_to_clk().
This is often because init_programmable_clock lacks a __init
annotation or the annotation of at91_css_to_clk is wrong.
In this case the only calls to and from init_programmable_clock()
are from code marked as "__init", so this fix is trivially correct.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Uwe Kleine-Knig <Uwe.Kleine-Koenig@digi.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
On the sam9 EK boards, the LCD backlight is hooked up to a PWM output from
the LCD controller. It's controlled by "contrast" registers though.
This patch lets boards declare that they have that kind of backlight
control. The driver can then export this control, letting screenblank and
other operations actually take effect ... reducing the typically
substantial power drain from the backlight.
Note that it's not fully cooked
- doesn't force backlight off during system suspend
- the "power" and "blank" events may not be done right
This should be easily added in the future.
[nicolas.ferre@atmel.com: remove unneeded inline and rename functions]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Andrew Victor <linux@maxim.org.za>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* at91:
[ARM] 4802/1: Fix typo and remove vague comment
[ARM] 4660/3: at91: allow selecting UART for early kernel messages
[ARM] 4739/1: at91sam9263: make gpio bank C and D irqs work
* ixp:
[ARM] 4809/2: ixp4xx: Merge dsmg600-power.c into dsmg600-setup.c
[ARM] 4808/2: ixp4xx: Merge nas100d-power.c into nas100d-setup.c
[ARM] 4807/2: ixp4xx: Merge nslu2-power.c into nslu2-setup.c
[ARM] 4806/1: ixp4xx: Ethernet support for the nslu2 and nas100d boards
[ARM] 4805/1: ixp4xx: Use leds-gpio driver instead of IXP4XX-GPIO-LED driver
[ARM] 4715/2: Ethernet support for IXDP425 boards
[ARM] 4714/2: Headers for IXP4xx built-in Ethernet and WAN drivers
[ARM] 4713/3: Adds drivers for IXP4xx QMgr and NPE features
[ARM] 4712/2: Adds functions to read and write IXP4xx "feature" bits
[ARM] 4774/2: ixp4xx: Register dsmg600 rtc i2c_board_info
[ARM] 4773/2: ixp4xx: Register nas100d rtc i2c_board_info
[ARM] 4772/2: ixp4xx: Register nslu2 rtc i2c_board_info
[ARM] 4769/2: ixp4xx: Button updates for the dsmg600 board
[ARM] 4768/2: ixp4xx: Button and LED updates for the nas100d board
[ARM] 4767/2: ixp4xx: Add bitops.h include to io.h
[ARM] 4766/2: ixp4xx: Update ixp4xx_defconfig, enabling all supported boards
* master:
[ARM] 4810/1: - Fix 'section mismatch' building warnings
[ARM] xtime_seqlock: fix more ARM machines for xtime deadlocking
[ARM] 21285 serial: fix build error
* misc:
[ARM] 4736/1: Export atags to userspace and allow kexec to use customised atags
* pxa:
[ARM] 4798/1: pcm027: fix missing header file
[ARM] 4803/1: pxa: fix building issue of poodle.c caused by patch 4737/1
[ARM] 4801/1: pxa: fix building issues of missing pxa2xx-regs.h
[ARM] pxa: introduce sysdev for pxa3xx static memory controller
[ARM] pxa: add preliminary suspend/resume code for pxa3xx
[ARM] pxa: introduce sysdev for GPIO register saving/restoring
[ARM] pxa: introduce sysdev for IRQ register saving/restoring
[ARM] pxa: fix the warning of undeclared "struct pxaohci_platform_data"
[ARM] pxa: change set_kset_name() to direct name assignment for MFP sysclass
* realview:
[ARM] 4822/1: RealView: Change the REALVIEW_MPCORE configuration option
[ARM] 4821/1: RealView: Remove the platform dependencies from localtimer.c
[ARM] 4820/1: RealView: Select the timer IRQ at run-time
[ARM] 4819/1: RealView: Fix entry-macro.S to work with multiple platforms
[ARM] 4818/1: RealView: Add core-tile detection
[ARM] 4817/1: RealView: Move the AMBA resource definitions to realview_eb.c
[ARM] 4816/1: RealView: Move the platform-specific definitions into board-eb.h
[ARM] 4815/1: RealView: Add clockevents suport for the local timers
[ARM] 4814/1: RealView: Add broadcasting clockevents support for ARM11MPCore
[ARM] 4813/1: Add SMP helper functions for clockevents support
[ARM] 4812/1: RealView: clockevents support for the RealView platforms
[ARM] 4811/1: RealView: clocksource support for the RealView platforms
Currently early kernel messages, i.e., those from uncompression, go to the
debugging UART. And if it is enabled in the platform configuration, but
not initialized by the bootloader, the machine hangs, waiting for UART
status change. Besides, having those messages on another UART - typically
the console UART - may be preferrable. This patch allows selecting the
UART in kernel configuration.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
On the at91sam9263, IRQs for GPIO banks C and D don't currently work.
This is because banks C, D, and E share one clock and toplevel IRQ, but
the AT91 code setting up and handling GPIO IRQs expects no sharing.
This patch:
- Fixes GPIO IRQ setup and handling to cope with GPIO banks that are
shared like on sam9263 chips, by setting up a list of those banks
and making the IRQ dispatching logic scan that list.
- Precomputes the address of each bank's registers, saving it with
other per-bank data so that it no longer needs to be constantly
recomputed during IRQs and other GPIO operations. That shrinks
hot-path code, while helping the GPIO bank irq updates.
- Fixes a minor bug where IRQ_TYPE_NONE was wrongly rejected (it just
means "use the default", which is "both edges" here).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
move update_process_times() out from under xtime_lock.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
On ACPI systems the target state set by acpi_pm_set_target() is
reset by acpi_pm_finish(), but that need not be called if the
suspend fails. All platforms that use the .set_target() global
suspend callback are affected by analogous issues.
For this reason, we need an additional global suspend callback that
will reset the target state regardless of whether or not the suspend
is successful. Also, it is reasonable to rename the .set_target()
callback, since it will be used for a different purpose on ACPI
systems (due to ACPI 1.0x code ordering requirements).
Introduce the global suspend callback .end() to be executed at the
end of the suspend sequence and rename the .set_target() global
suspend callback to .begin().
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
From: Nicolas Ferre <nicolas.ferre@rfo.atmel.com>
On the at92sam9263ek board, tell the input subsystem about the buttons.
This patch is taken from Andrew Victor's at91 patchset, then updated to
match the latest kernel code and to use labels printed on the board.
Also update the at91sam9261ek buttons to cope with input changes.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for the Atmel AT91CAP9A-DK Evaluation Kit board.
Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for Atmel's AT91CAP9 Customizable Microcontroller family.
<http://www.atmel.com/products/AT91CAP/Default.asp>
Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Currently the udc pullup is enabled by default on boot. If the device
is connected to a host at this time, the host starts the negotiation
before the udc/gadget driver is ready to handle it.
Signed-off-by: Christian Glindkamp <christian.glindkamp@taskit.de>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add NEW_LEDs support for the following boards:
- Cogent CSB337
- Atmel AT91RM9200-DK
- Atmel AT91RM9200-EK
- Atmel AT91SAM9263-EK
Mostly based on patch from David Brownell.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Due to errata regarding the handling of SPI CS0 on the AT91RM9200, the
atmel_spi driver drives CS0 from the SPI controller and not as a GPIO
pin.
We therefore need to configure CS0 for use by the controller
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Support for the 3 GPIO-connected buttons on the CSB300 board.
Based on wakeup testing code from David Brownell.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move the LED initialization code out of the various *_devices.c files,
and into leds.c.
Also add support for NEW_LEDs.
Patch from David Brownell.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Modify the UART initialization to allow the board-initialization code
to specify which pins are connected, and which pins should therefore
be initialized.
The current at91_init_serial() will continue to work as-is, but is
marked as "deprecated" and will be removed once the board-specific
files has been updated to use the new interface.
As in the AVR32 code, we assume that the TX and RX pins will always be
initialized.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Map the complete memory region (SZ_256M) as is done on the other AT91
processors.
The SMC_SMARTMEDIA bit should be set in the EBI controller to enable
the hardware NAND logic.
(Patch from Sascha Erlacher)
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Core support of the Atmel SSC library for all Atmel AT91 processors.
Based on David Brownell's initial patch for the AT91RM9200.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Replace hard-coded DMA mask (0xffffffff) with DMA_BIT_MASK(32) as
defined in dma-mapping.h.
Set "dma_mask" field for the UART platform_devices.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add platform_device and initialization for the RTT (Real Time Timer)
and WDT (Watchdog) integrated in the Atmel AT91SAM9 processors.
For SAM9263, register both RTT peripherals.
[From: David Brownell <dbrownell@users.sourceforge.net>]
Provide platform_resources for RTT peripherals
[From: David Brownell <dbrownell@users.sourceforge.net>]
Add support for RTC peripheral on AT91SAM9RL (same RTC peripherals as
AT91RM9200)
[From: David Brownell <dbrownell@users.sourceforge.net>]
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for the Image Sensor Interface (ISI) peripheral integrated
in the Atmel AT91SAM9263 processor.
Patch from MaLiK
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for STN LCD displays on Atmel AT91SAM9261-based boards.
Patch from Nicolas Ferre.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
On the at92sam9263ek board, tell the MACB driver the IRQ used
by its PHY. This patch is taken from Andrew Victor's 2.6.23-at91
patchset; it matches board schematics. (But it's currently a NOP
since the MACB driver doesn't yet use PHY irqs.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This makes HZ configurable on AT91, following the model used on OMAP.
It defaults to a power of two on AT91rm9200 chips, avoiding rounding
errors which come from dividing a 32 KiHz clock to generate scheduler
irqs; and uses 100 on AT91sam926x chips, using MCK/16 (multi-MHZ).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Remy Bhmer <linux@bohmer.net>
Acked-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Slight tweaking of the default interrupt priorities (AIC) for the
integrated peripherals on the AT91RM9200, AT91SAM9260, AT91SAM9261 and
AT91SAM9263 processors.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add STN LCD support on the Atmel AT91SAM9261-EK board.
Uses a black and white screen from Hitachi: SP06Q002.
Signed-off-by: Nicolas Ferre <nicolas.ferre@rfo.atmel.com>
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds a debug interface (if CONFIG_DEBUG_FS is selected) to
display the basic configuration and current state of the GPIO pins on
the Atmel AT91 processors.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
- Add missing i2c_board_info struct for at91rm9200
Signed-off-by: Jan Altenberg <jan.altenberg@linutronix.de>
Acked-by: Andrew Victor <avictor.za@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The incorrect GPIO pins are being initialized for the buttons on the
Atmel AT91SAM9261-EK board. This buggy configuration turns LCD screen
blue...
Signed-off-by: Nicolas Ferre <nicolas.ferre@rfo.atmel.com>
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The AT91 I2C driver is currently marked as "broken" due to hardware
issues. This patch enables AT91-based platforms to also use the
bitbanged GPIO for I2C.
This updates platform setup logic (setting up an i2c-gpio device
using the same pins as the i2c-at91 device, unless only the BROKEN
driver is enabled).
Also make use of the new-style initialization of I2C devices using
i2c_register_board_info().
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The calculation for the Master clock divisor (MDIV) is different on the
SAM9 processors than on the AT91RM9200.
Orignal patch from Sascha Erlacher.
Also use the defined AT91_PMC_PRES instead of hard-coded bitmasks.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix the various misspellings of "system", controller", "interrupt" and
"[un]necessary".
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
The name of 'struct pm_ops' suggests that it is related to the power
management in general, but in fact it is only related to suspend. Moreover,
its name should indicate what this structure is used for, so it seems
reasonable to change it to 'struct platform_suspend_ops'. In that case, the
name of the global variable of this type used by the PM core and the names of
related functions should be changed accordingly.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: Len Brown <lenb@kernel.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move the definition of 'struct pm_ops' and related functions from <linux/pm.h>
to <linux/suspend.h> .
There are, at least, the following reasons to do that:
* 'struct pm_ops' is specifically related to suspend and not to the power
management in general.
* As long as 'struct pm_ops' is defined in <linux/pm.h>, any modification of it
causes the entire kernel to be recompiled, which is unnecessary and annoying.
* Some suspend-related features are already defined in <linux/suspend.h>, so it
is logical to move the definition of 'struct pm_ops' into there.
* 'struct hibernation_ops', being the hibernation-related counterpart of
'struct pm_ops', is defined in <linux/suspend.h> .
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: Len Brown <lenb@kernel.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
GENERIC_TIME and GENERIC_CLOCKEVENTS support for the at91rm9200.
- Oneshot mode (used for NO_HZ and high res timers) uses the
alarm to emulate a real oneshot timer; the trickiest bit is
how to avoid some lowlevel races. Thanks to Remy Bohmer for
various fixes to this code.
- Tighten up periodic mode support using the PIT.
- Streamline reads of the 32KHz counter. Thanks to Marc Pignat
for some testing results: the CRTR register has *very* odd
behavior. The reread appears to work around stranger glitches
than just getting an old clock value (which would quickly
self-correct).
- Remove the rounding-up of tick_usec to 10.009 msec (32KiHz/100),
since that no longer acts correct (time increases too fast).
Note that the at91sam9 and at91x40 chips need other solutions,
since they don't have the same system timer module.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Bill Gatliff <bgat@billgatliff.com>
Acked-by:Remy Bohmer <linux@bohmer.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Configuration support for the AT91x40 CPU and EB01 board.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Makefile build support for the Atmel AT91x40 CPU and EB01 board support.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Support for the Atmel EB01 board (based on the Atmel AT91x40 CPU).
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Prototypes for the at91x40 CPU support functions.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Interrupt setup support for the Atmel AT91x40 CPU family.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Support for the timers in the Atmel AT91x40 family of CPUs.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
- Include atmel_lcdc.h in at91sam926{1,3}_devices.c
Signed-off-by: Jan Altenberg <jan.altenberg@linutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert the AT91RM9200 platform-setup code to use the new atmel_spi
driver (and manually-driven chip-selects), instead of the legacy
AT91-only SPI stack.
The AT91SAM9 processors are already using the atmel_spi driver.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Update csb337 board specific init to support "new style" rtc-ds1307 code.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Andrew Victor <andrew@sanpeople.com>
Cc: Bill Gatliff <bgat@billgatliff.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Register the GPIO-connected buttons on the SAM9261-EK board as a
"gpio-keys" platform device.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add board-specific setup for the LCD on the Atmel AT91SAM9261-EK and
AT91SAM9263-EK boards.
Signed-off-by: Nicolas Ferre <nicolas.ferre@rfo.atmel.com>
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit 52ade9b3b9 changed the suspend code
ordering to execute pm_ops->prepare() after the device model per-device
.suspend() calls in order to fix some ACPI-related issues. Unfortunately, it
broke the at91 platform which assumed that pm_ops->prepare() would be called
before suspending devices.
at91 used pm_ops->prepare() to get notified of the target system sleep state,
so that it could use this information while suspending devices. However, with
the current suspend code ordering pm_ops->prepare() is called too late for
this purpose. Thus, at91 needs an additional method in 'struct pm_ops' that
will be used for notifying the platform of the target system sleep state.
Moreover, in the future such a method will also be needed by ACPI.
This patch adds the .set_target() method to 'struct pm_ops' and makes the
suspend code call it, if implemented, before executing the device model
per-device .suspend() calls. It also modifies the at91 code to use
pm_ops->set_target() instead of pm_ops->prepare().
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Len Brown <lenb@kernel.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When suspending to slow-clock mode, at91_pm_verify_clocks() is called to
ensure that all the clocks are disabled or in the correct state.
This patch replaces the "#warning TODO" messages for the SAM9 processors
with the correct code.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The number of programmable clocks available on the AT91 processors can
differ, therefore do not always display the contents of the PMC_PCKR(0)
.. PMC_PCKR(3) registers (ie, assume there are 4 clocks).
If CONFIG_AT91_PROGRAMMABLE_CLOCKS is enabled, the programmable clocks
will be registered like the other system/peripheral clocks, and the
state of the programmable clocks will be displayed like with the other
clocks.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for the Atmel AT91SAM9RL-EK development board.
Signed-off-by: Nicolas Ferre <nicolas.ferre@rfo.atmel.com>
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Define SZ_512, SZ_256 and SZ_16 in asm-arm/sizes.h.
Remove the definitions from the at91*_devices.c files.
(Dependent on ARM patch #4370/2)
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for Atmel's new AT91SAM9RL range of processors.
Includes similar peripherals as other AT91SAM9 processors, but with a
High-speed USB controller and various sizes of internal SRAM.
Signed-off-by: Nicolas Ferre <nicolas.ferre@rfo.atmel.com>
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Attached you can find a patch needed to make the LEDS for 'CPU-Idle'
and 'Timer' work on the AT91SAM9261-EK board. The kernel configuration
options are already there, but the implementation is not available.
Signed-off-by: Remy Bohmer <l.pinguin@gmail.com>
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix various typos in kernel docs and Kconfigs, 2.6.21-rc4.
Signed-off-by: Matt LaPlante <kernel1@cyberdogtech.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Add IRQF_IRQPOLL for each timer interrupt.
Signed-off-by: Bernhard Walle <bwalle@suse.de>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Various small changes for the Atmel AT91SAM9260-EK and AT91SAM9263-EK
boards.
SAM9260-EK:
- Register I2C device.
SAM9263-EK:
- Add platform_data and register MACB device.
(Patch by Nicolas Ferre)
- Add platform_data and register AC97 device.
(Patch by Nicolas Ferre)
- Register I2C device.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for the ADS7846 Touchscreen found on the Atmel
AT91SAM9263-EK board.
Signed-off-by: Nicolas Ferre <nicolas.ferre@rfo.atmel.com>
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for the ADS7846 Touchscreen found on the Atmel
AT91SAM9261-EK board.
Original patch by Morten Larsen.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Define resources, platform_device and device registration functions for
the LCD and AC97 controllers on the AT91SAM9263.
Also update the AT91SAM9261 to use the common atmel_lcdfb driver.
Signed-off-by: Nicolas Ferre <nicolas.ferre@rfo.atmel.com>
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Define and register the remaining peripheral clocks for the AT91
processors.
AT91SAM9261 clocks patch by Ivan Zhakov.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch series cleans up some misconceptions about pm_ops. Some users of
the pm_ops structure attempt to use it to stop the user from entering suspend
to disk, this, however, is not possible since the user can always use
"shutdown" in /sys/power/disk and then the pm_ops are never invoked. Also,
platforms that don't support suspend to disk simply should not allow
configuring SOFTWARE_SUSPEND (read the help text on it, it only selects
suspend to disk and nothing else, all the other stuff depends on PM).
The pm_ops structure is actually intended to provide a way to enter
platform-defined sleep states (currently supported states are "standby" and
"mem" (suspend to ram)) and additionally (if SOFTWARE_SUSPEND is configured)
allows a platform to support a platform specific way to enter low-power mode
once everything has been saved to disk. This is currently only used by ACPI
(S4).
This patch:
The pm_ops.pm_disk_mode is used in totally bogus ways since nobody really
seems to understand what it actually does.
This patch clarifies the pm_disk_mode description.
It also removes all the arm and sh users that think they can veto suspend to
disk via pm_ops; not so since the user can always do echo shutdown >
/sys/power/disk, they need to find a better way involving Kconfig or such.
ACPI is the only user left with a non-zero pm_disk_mode.
The patch also sets the default mode to shutdown again, but when a new pm_ops
is registered its pm_disk_mode is selected as default, that way the default
stays for ACPI where it is apparently required.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: David Brownell <david-b@pacbell.net>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: <linux-pm@lists.linux-foundation.org>
Cc: Len Brown <lenb@kernel.org>
Acked-by: Russell King <rmk@arm.linux.org.uk>
Cc: Greg KH <greg@kroah.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrew Morton found a section mismatch warning in x86_64 triggered by a
wrongly placed __initdata marker.
git grep "struct __initdata" revealed that board-sam9260.c had the same
problem.
This patch fixes this by placing the __initdata marker correct. It was
checked with objdump that the variable was moved to .init.data by this
change.
Fixed an unrelated section mismatch warning while touching the file.
Both changes are only compile tested but obvious correct.
[Used at91sam9260ek_defconfig to get compile coverage]
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add the picotux 200 ARM board:
- Enable its machine type in the filter in head.S
- Add configuration option
- Add board initialisation
- Add default configuration
Signed-off-by: Simon Richter <Simon.Richter@kleinhenz.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix the NAND flash timings on the AT91SAM9260.
The current timings lead to the detection of a number of bad blocks.
These timings are now set the same as on the AT91SAM9263.
Patch from Nicolas Ferre.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
It's been pointed out that output GPIOs should have an initial value, to
avoid signal glitching ... among other things, it can be some time before
a driver is ready. This patch corrects that oversight, fixing
- documentation
- platforms supporting the GPIO interface
- users of that call (just one for now, others are pending)
There's only one user of this call for now since most platforms are still
using non-generic GPIO setup code, which in most cases already couples the
initial value with its "set output mode" request.
Note that most platforms are clear about the hardware letting the output
value be set before the pin direction is changed, but the s3c241x docs are
vague on that topic ... so those chips might not avoid the glitches.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Andrew Victor <andrew@sanpeople.com>
Acked-by: Milan Svoboda <msvoboda@ra.rockwell.com>
Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The new gpio_direction_input() and gpio_direction_output() functions
were both enabling output mode. When configuring a GPIO for input mode,
you need to program the ODR (Output Disable Register).
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The duplicate file "include/asm-arm/arch-at91rm9200/entry-macro.S" can
be removed - it was already moved to include/asm-arm/arch-at91/.
Fix 3 small typo's - two in comments, and the incorrect clock was
specified for the LCD device.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (117 commits)
[ARM] 4058/2: iop32x: set ->broken_parity_status on n2100 onboard r8169 ports
[ARM] 4140/1: AACI stability add ac97 timeout and retries
[ARM] 4139/1: AACI record support
[ARM] 4138/1: AACI: multiple channel support for IRQ handling
[ARM] 4211/1: Provide a defconfig for ns9xxx
[ARM] 4210/1: base for new machine type "NetSilicon NS9360"
[ARM] 4222/1: S3C2443: Remove reference to missing S3C2443_PM
[ARM] 4221/1: S3C2443: DMA support
[ARM] 4220/1: S3C24XX: DMA system initialised from sysdev
[ARM] 4219/1: S3C2443: DMA source definitions
[ARM] 4218/1: S3C2412: fix CONFIG_CPU_S3C2412_ONLY wrt to S3C2443
[ARM] 4217/1: S3C24XX: remove the dma channel show at startup
[ARM] 4090/2: avoid clash between PXA and SA1111 defines
[ARM] 4216/1: add .gitignore entries for ARM specific files
[ARM] 4214/2: S3C2410: Add Armzone QT2410
[ARM] 4215/1: s3c2410 usb device: per-platform vbus_draw
[ARM] 4213/1: S3C2410 - Update definition of ADCTSC_XY_PST
[ARM] 4098/1: ARM: rtc_lock only used with rtc_cmos
[ARM] 4137/1: Add kexec support
[ARM] 4201/1: SMP barriers pair needed for the secondary boot process
...
Fix up conflict due to typedef removal in sound/arm/aaci.h
- Remove a duplicated define for AT91_RSTC_KEY
- Set AT91_RSTC_KEY to the correct value
- Replace the hardcoded keys in at91sam9620.c and at91sam9261.c
by AT91_RSTC_KEY
Signed-off-by: Jan Altenberg <jan@linutronix.de>
Acked-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for the Atmel AT91SAM9XE range of processors. These are
basically AT91SAM9260's with different amounts of internal SRAM and
Flash.
We make use of the existing AT91SAM9260 support, but just perform
run-time detection of the size of the internal SRAM.
Original patch from Nicolas Ferre.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The MACB Ethernet driver searches for a "macb_clk" clock, so rename the
"ether_clk" on the SAM9260 and SAM9263 to "macb_clk".
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Unconditionally disabling the PCKs (Programmable Clocks) is not a good
idea as it breaks boards that depend on those clocks being enabled by
bootloaders.
Therefore only disable unused clocks late in the init process, giving
the board init code the chance to claim the clock.
Patch from Steven Scholz.
Since the HCK clocks on SAM9261 are already being registered as a
independent clocks, we don't need the special case for HCK0 on the
SAM9261. Platform-init code and drivers should use the clock API to
enable/disable the clock.
Patch from Nicolas Ferre.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The GPIO pin setup should be handed by the platform-setup code, and not
directly by the driver.
Original patch from David Brownell.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix an overrun in the AT91SAM9 gettimeoffset() function. This causes
the time value returned by gettimeofday() to jump "backwards".
Original patch from Michel Benoit.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Define the physically mapped flash on the Cogent CSB337 and CSB637
boards.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Define the Timer/Counter Unit clocks on the AT91RM9200, AT91SAM9260 and
AT91SAM9261 processors.
Original patch from David Brownell.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for the Atmel AT91SAM9263-EK board.
Original patch from Nicolas Ferre.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for the Atmel AT91SAM9263 processor. It is similar to the
AT91SAM9260 but with more integrated peripherals, 5 GPIO banks, etc.
Original patch from Nicolas Ferre.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The Atmel AT91SAM9263 processor includes many more integrated
peripherals than Atmel's previous ARM9-based AT91 processors, so this
has necessitated a few changes to the core AT91 support.
These changes are:
* The system peripheral I/O region we remap has increased from
0xFFFA0000..0xFFFFFFFF to 0xFFF78000..0xFFFFFFFF.
* The increased I/O region forces changes to entry-macro.S and
debug-macro.S due to ARM's limited immediate offset addressing
modes.
* Maximum number of GPIO banks increases to 5.
* 2 MMC controllers so the board-setup code needs to specify which
controller it wishes to use when calling at91_add_device_mmc().
Original patch from Nicolas Ferre.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Now that Linux includes support for the Atmel AT91SAM9260 and
AT91SAM9261 processors in addition to the original Atmel AT91RM9200
(with support for more AT91 processors pending), the "mach-at91rm9200"
and "arch-at91rm9200" directories should be renamed to indicate their
more generic nature.
The following git commands should be run BEFORE applying this patch:
git-mv arch/arm/mach-at91rm9200 arch/arm/mach-at91
git-mv include/asm-arm/arch-at91rm9200 include/asm-arm/arch-at91
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Samuel R. C. Vale