TG3_IRQ_MAX_VECS should be seen as the maximum number of vectors that
any device could be expected to use. tp->irq_max represents the maximum
number of vectors the current device can use. This patch clarifies the
semantics of the code to match the above description.
Reviewed-by: Benjamin Li <benli@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adjusts the driver to use the tg3_start_xmit_dma_bug()
transmit routine for all revisions of 5717 asic rev devices and then
allows the driver to attach to B0 and later devices.
Reviewed-by: Benjamin Li <benli@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NCSI firmware does not accept APE events. It relies on a "driver state"
location in shared memory to tell it what the driver's current state is.
This patch pivots the code to use the new driver state scheme.
Reviewed-by: Benjamin Li <benli@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was recently discovered that enabling TSS can lockup the device.
This patch disables the feature until a suitable workaround can be
found.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Earlier versions of tg3 devices had a problem where the read DMA FIFO
could be overrun in certain edge conditions. The fix was to limit the
number of rx BDs the hardware would fetch at a time. For later devices
(5761, 5784 and later ASIC revs), there is a hardware fix that must be
enabled to fix the same problem. This patch adds that hardware fix.
There is a gap in the ASIC revision lineage where neither fix is
applied. This is intentional as these ASIC revisions are not afflicted
by the bug.
Reviewed-by: Benjamin Li <benli@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Accept already has socket locking.
[ Extend socket locking over TCP_LISTEN state test. -DaveM ]
Signed-off-by: Andrew Hendry <andrew.hendry@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Accept updates socket values in 3 lines so wrapped with lock_sock.
Signed-off-by: Andrew Hendry <andrew.hendry@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Listen updates socket values and needs lock_sock.
Signed-off-by: Andrew Hendry <andrew.hendry@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code is quite convoluted, simplify it. This also avoids calling
e1000_request_irq() without testing the value it returned, which was
bad.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Bruce Allan <bruce.w.allan@intel.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Default number of rx buffers will be divided equally
between allocated queues. This will decrease amount of
pre-allocated buffers on systems with multiple CPUs.
User can override this behavior with ethtool -G.
Minimum amount of rx buffers per queue set to 128.
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Empty received URBs are currently counted as errors but the device sends them
sometimes as part of regular traffic - so remove this check.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix that usb_string() return value is not checked for error (negative value).
Also change the ignore message a bit and lower its level to info.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modifying an object twice without an intervening sequence point is
undefined.
Signed-off-by: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modifying an object twice without an intervening sequence point is
undefined.
Signed-off-by: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch to adds support for PM hooks into sundance driver
Signed-off-by: Denis Kirjanov <dkirjanov@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allocate hash tables for every online cpus, not every possible ones.
NUMA aware allocations.
Dont use a full page on arches where PAGE_SIZE > 1024*sizeof(void *)
misc:
__percpu , __read_mostly, __cpuinit annotations
flow_compare_t is just an "unsigned long"
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that est_tree_lock is acquired with BH protection, the other
call is unnecessary.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use rcu_dereference_rtnl() helper
Change hard coded constants in fib_flag_trans()
7 -> RTN_UNREACHABLE
8 -> RTN_PROHIBIT
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This requires some reorganisation of channel setup and teardown to
ensure that we can always roll-back a failed change.
Based on work by Steve Hodgson <shodgson@solarflare.com>
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Allow the ring size to be specified in non
power-of-two sizes (for instance to limit
the amount of receive buffers).
- Automatically size the event queue.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will allow for reallocation of channel structures and rings.
Change module parameter separate_tx_channels to be read-only, since we
now require its value to be constant.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for changes to the way channels and queue structures
are allocated, revise the macros and functions used to look up and
iterator over them.
- Replace efx_for_each_tx_queue() with iteration over channels then TX
queues
- Replace efx_for_each_rx_queue() with iteration over channels then RX
queues (with one exception, shortly to be removed)
- Introduce efx_get_{channel,rx_queue,tx_queue}() functions to look up
channels and queues by index
- Introduce efx_channel_get_{rx,tx}_queue() functions to look up a
channel's queues
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we allocate DMA descriptor rings and event rings using
pci_alloc_consistent() which selects non-blocking behaviour from the
page allocator (GFP_ATOMIC). This is unnecessary, and since we
currently allocate a single contiguous block for each ring (up to 32
pages!) these allocations are likely to fail if there is any
significant memory pressure. Use dma_alloc_coherent() and GFP_KERNEL
instead.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rx_over_errors appears to be intended as a count of packets that
overflow a packet buffer in the NIC. Given that we implement a
cut-through receive path, this should always be 0.
rx_dropped appears to be the correct counter for packets dropped due
to lack of host buffers.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Calculating rx_bad as rx_packets - rx_good is unnecessary and
incorrect, since rx_good does not include control frames (e.g.
pause frames) and rx_packets does.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace sizeof(bnx2x_parity_mask)/(sizeof(bnx2x_parity_mask[0]) with
ARRAY_SIZE(bnx2x_parity_mask) in drivers/net/bnx2x/bnx2x_main.c
Signed-off-by: Nikitas Angelinas <nikitasangelinas@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 'wwan' devtype is meant for devices that require preconfiguration
and *every* time setup before the ethernet interface can be used, like
cellular modems which require a series of setup commands on serial ports
or other mechanisms before the ethernet interface will handle packets.
As ipheth only requires one-per-hotplug pairing setup with no
preconfiguration (like APN, phone #, etc) and the network interface is
usable at any time after that initial setup, remove the incorrect
devtype wwan.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove all the volatile keywords where they were used, switch to using the
proper readl/writel accessors.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace asm/io.h and asm/cpu.h wih linux/io.h and linux/cpu.h
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use pr_(info|err) and pr_cont where required instead of calls to printk.
Add missing pr_fmt to the driver.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
One line has not been changed because it would not improve readability.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the following checkpatch.pl warnings:
- spaces after tabs
- space between function and arguments
- one-line statement braces
- tabs instead of spaces
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Matt Carlson