Drop the old Sysbus init and use instance_init and
DeviceClass::realize instead
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Message-id: 20161023091816.3839-2-zxq_yx_007@163.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The STM32F2XX Timer emulator uses a 16 bit prescaler value to
limit the timer clock rate. It does that by dividing the timer
frequency. If the prescaler 's->tim_psc' was set to be UINT_MAX,
it'd lead to divide by zero error. Limit prescaler value to 16
bits to avoid it.
Reported-by: Huawei PSIRT <psirt@huawei.com>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Message-id: 1476800269-31902-1-git-send-email-ppandit@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Change 2293c27fad (i2c: implement broadcast write) added broadcast
capability to the I2C bus, but it broke SMBus read transactions.
An SMBus read transaction does two i2c_start_transaction() calls
without an intervening i2c_end_transfer() call. This will
result in i2c_start_transfer() adding the same device to the
current_devs list twice, and then the ->event() for the same
device gets called twice in the second call to i2c_start_transfer(),
resulting in the smbus code getting confused.
Note that this happens even with pure I2C devices when simulating
SMBus over I2C.
This fix only scans the bus if the current set of devices is empty.
This means that the current set of devices stays fixed until
i2c_end_transfer() is called, which is really what you want.
This also deletes the empty check from the top of i2c_end_transfer().
It's unnecessary, and it prevents the broadcast variable from being
set to false at the end of the transaction if no devices were on
the bus.
Cc: KONRAD Frederic <fred.konrad@greensocs.com>
Cc: Alistair Francis <alistair.francis@xilinx.com>
Cc: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Cc: Kwon <hyun.kwon@xilinx.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: KONRAD Frederic <fred.konrad@greensocs.com>
Tested-by: KONRAD Frederic <fred.konrad@greensocs.com>
Message-id: 1470153614-6657-1-git-send-email-minyard@acm.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
ARM A9MP processor has a peripheral timer with an auto-increment
register, which holds an increment step value. A user could set
this value to zero. When auto-increment control bit is enabled,
it leads to an infinite loop in 'a9_gtimer_update' while
updating comparator value. Remove this loop incrementing the
comparator value.
Reported-by: Li Qiang <liqiang6-s@360.cn>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Message-id: 1476733226-11635-1-git-send-email-ppandit@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch builds an IORT table that features a root complex node and
an ITS node. This complements the ITS description in the ACPI MADT
table and allows vhost-net on ACPI guest.
Signed-off-by: Prem Mallappa <prem.mallappa@broadcom.com>
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-id: 1476707466-14300-3-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Current ARM MPTimer implementation uses QEMUTimer for the actual timer,
this implementation isn't complete and mostly tries to duplicate of what
generic ptimer is already doing fine.
Conversion to ptimer brings the following benefits and fixes:
- Simple timer pausing implementation
- Fixes counter value preservation after stopping the timer
- Properly handles prescaler != 0 / counter = 0 / load = 0 cases
- Code simplification and reduction
Bump VMSD to version 3, since VMState is changed and is not compatible
with the previous implementation.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Message-id: 37f378c33bb5a28d5cd71167a6bd5bff5e59cbc3.1475421224.git.digetx@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
For most of the timers counter starts to decrement after first period
expires. Due to rounding down performed by the ptimer_get_count, it returns
counter - 1 for the running timer, so that for the ptimer user it looks
like counter gets decremented immediately after running the timer. Add "no
counter round down" policy that provides correct behaviour for those timers.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Message-id: ef39622d0ebfdc32a0877e59ffdf6910dc3db688.1475421224.git.digetx@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Immediate counter re-load on setting (or on starting to run with)
counter = 0 is a wrong behaviour for some of the timers. Add "no
immediate reload" policy that provides correct behaviour for such timers.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Message-id: bf9385cd2550ca451d564fa46007688cee3f3d9d.1475421224.git.digetx@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Performing trigger on setting (or starting to run with) counter = 0 could
be a wrong behaviour for some of the timers, provide "no immediate trigger"
policy to maintain correct behaviour for such timers.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Message-id: 72c0319cf2ec599f22397b7da280c06c34dc40dd.1475421224.git.digetx@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Currently, periodic timer that has load = delta = 0 performs trigger
on timer reload and stops, printing a "period zero" error message.
Introduce new policy that makes periodic timer to continuously trigger
with a period interval in case of load = 0.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Message-id: 632b23dd11055d9bd5e338d66b38fac0bd51462e.1475421224.git.digetx@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Currently, periodic counter wraps around immediately once counter reaches
"0", this is wrong behaviour for some of the timers, resulting in one period
being lost. Add new ptimer policy that provides correct behaviour for such
timers, so that counter stays with "0" for a one period before wrapping
around.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Message-id: f22a670cf1f4be298b31640cb5f4be1df0f20ab6.1475421224.git.digetx@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Since the virt board model will never create a CPU which is
pre-ARMv7, we know that our minimum page size is 4K and can
set minimum_page_bits accordingly, for improved performance.
Note that this is a migration compatibility break, so
we introduce it only for the virt-2.8 machine and onward;
virt-2.7 continues using the old 1K pages.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
No need to count the users of a CharDriverState, it can rely on the fact
of whether there is a CharBackend associated or if there is enough space
in the muxer.
Simplify and fold chr_mux_new_fe() in qemu_chr_fe_init() since there is
a single user now. Also switch from fprintf to raising error instead.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20161022100951.19562-5-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Usage has long been removed, since commit f220174de8.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20161022100951.19562-2-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
No need to keep explicit_fe_open around if it affects only a
qemu_chr_fe_set_handlers(). Use an additional argument instead.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20161022095318.17775-24-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Since the hanlders are associated with a CharBackend, rather than the
CharDriverState, it is more appropriate to store in CharBackend. This
avoids the handler copy dance in qemu_chr_fe_set_handlers() then
mux_chr_update_read_handler(), by storing the CharBackend pointer
directly.
Also a mux CharDriver should go through mux->backends[focused], since
chr->be will stay NULL. Before that, it was possible to call
chr->handler by mistake with surprising results, for ex through
qemu_chr_be_can_write(), which would result in calling the last set
handler front end, not the one with focus.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20161022095318.17775-22-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In most cases, front ends do not care about the side effect of
CharBackend, so we can simply skip the checks and call the qemu_chr_fe
functions even without associated CharDriver.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20161022095318.17775-20-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Now that all front end use qemu_chr_fe_init(), we can move chardev
claiming in init(), and add a function deinit() to release the chardev
and cleanup handlers.
The qemu_chr_fe_claim_no_fail() for property are gone, since the
property will raise an error instead. In other cases, where there is
already an error path, an error is raised instead. Finally, other cases
are handled by &error_abort in qemu_chr_fe_init().
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20161022095318.17775-19-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This also switches from qemu_chr_add_handlers() to
qemu_chr_fe_set_handlers(). Note that qemu_chr_fe_set_handlers() now
takes the focus when fe_open (qemu_chr_add_handlers() did take the
focus)
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20161022095318.17775-16-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
qemu_chr_accept_input() and qemu_chr_disconnect() are only used by
frontend, so use qemu_chr_fe prefix.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20161022095318.17775-14-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Similar to previous change, for the remaining CharDriverState front ends
users.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20161022095318.17775-13-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Store the property in a CharBackend instead of CharDriverState*. This
also replace systematically chr by chr.chr to access the
CharDriverState*. The following patches will replace it with calls to
qemu_chr_fe CharBackend functions.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20161022095318.17775-12-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
ASAN complains about buffer overflow when running:
aarch64-softmmu/qemu-system-aarch64 -machine xilinx-zynq-a9
==476==ERROR: AddressSanitizer: heap-buffer-overflow on address 0x602000035e38 at pc 0x000000f75253 bp 0x7ffc597e0ec0 sp 0x7ffc597e0eb0
READ of size 8 at 0x602000035e38 thread T0
#0 0xf75252 in xilinx_spips_realize hw/ssi/xilinx_spips.c:623
#1 0xb9ef6c in device_set_realized hw/core/qdev.c:918
#2 0x129ae01 in property_set_bool qom/object.c:1854
#3 0x1296e70 in object_property_set qom/object.c:1088
#4 0x129dd1b in object_property_set_qobject qom/qom-qobject.c:27
#5 0x1297168 in object_property_set_bool qom/object.c:1157
#6 0xb9aeac in qdev_init_nofail hw/core/qdev.c:358
#7 0x78a5bf in zynq_init_spi_flashes /home/elmarco/src/qemu/hw/arm/xilinx_zynq.c:125
#8 0x78af60 in zynq_init /home/elmarco/src/qemu/hw/arm/xilinx_zynq.c:238
#9 0x998eac in main /home/elmarco/src/qemu/vl.c:4534
#10 0x7f96ed692730 in __libc_start_main (/lib64/libc.so.6+0x20730)
#11 0x41d0a8 in _start (/home/elmarco/src/qemu/aarch64-softmmu/qemu-system-aarch64+0x41d0a8)
0x602000035e38 is located 0 bytes to the right of 8-byte region [0x602000035e30,0x602000035e38)
allocated by thread T0 here:
#0 0x7f970b014e60 in malloc (/lib64/libasan.so.3+0xc6e60)
#1 0x7f96f15b0e18 in g_malloc (/lib64/libglib-2.0.so.0+0x4ee18)
#2 0xb9ef6c in device_set_realized hw/core/qdev.c:918
#3 0x129ae01 in property_set_bool qom/object.c:1854
#4 0x1296e70 in object_property_set qom/object.c:1088
#5 0x129dd1b in object_property_set_qobject qom/qom-qobject.c:27
#6 0x1297168 in object_property_set_bool qom/object.c:1157
#7 0xb9aeac in qdev_init_nofail hw/core/qdev.c:358
#8 0x78a5bf in zynq_init_spi_flashes /home/elmarco/src/qemu/hw/arm/xilinx_zynq.c:125
#9 0x78af60 in zynq_init /home/elmarco/src/qemu/hw/arm/xilinx_zynq.c:238
#10 0x998eac in main /home/elmarco/src/qemu/vl.c:4534
#11 0x7f96ed692730 in __libc_start_main (/lib64/libc.so.6+0x20730)
s->spi is allocated with the size of num_busses which may be 1 (by
default). Change to use a loop up to s->num_busses also for the
call to ssi_auto_connect_slaves().
Reported-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The CharDriverState.init() callback is no longer set since commit
a61ae7f88c and thus unused. The only user, the malta FGPA display has
been converted to use an event "opened" callback instead.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20161022095318.17775-7-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The CharDriverState.init() callback was introduced in commit
ceecf1d158. It is only called from text_console_do_init(), but it is no
longer set since commit a61ae7f88 (init assignment has been removed by
accident).
It seems correct to use an event callback instead and print the console
text on CHR_EVENT_OPENED. That way we can remove the single user of
CharDriverState init().
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20161022095318.17775-6-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Since commit b6607a1a20, serial_hds_isa_init() was introduced to
factor out serial_isa_init() loops. However, sun4uv shouldn't start from
0 when there is a mm serial on 0 already. Add a "from" argument to
serial_hds_isa_init().
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20161022095318.17775-5-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
16550A UART device uses an oscillator to generate frequencies
(baud base), which decide communication speed. This speed could
be changed by dividing it by a divider. If the divider is
greater than the baud base, speed is set to zero, leading to a
divide by zero error. Add check to avoid it.
Reported-by: Huawei PSIRT <psirt@huawei.com>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Message-Id: <1476251888-20238-1-git-send-email-ppandit@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Implement SUSE specific unplug protocol for emulated PCI devices
in PVonHVM guests. Its a simple 'outl(1, (ioaddr + 4));'.
This protocol was implemented and used since Xen 3.0.4.
It is used in all SUSE/SLES/openSUSE releases up to SLES11SP3 and
openSUSE 12.3.
In addition old (pre-2011) VMDP versions are handled as well.
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Stefano Stabellini <sstabellini@kernel.org>
Using 'vdev=sd[a-o]' will create an emulated LSI controller, which can
be used by the emulated BIOS to boot from disk. If the HVM domU has also
PV driver the disk may appear twice in the guest. To avoid this an
unplug of the emulated hardware is needed, similar to what is done for
IDE and NIC drivers already.
Since the SCSI controller provides only disks the entire controller can
be unplugged at once.
Impact of the change for classic and pvops based guest kernels:
vdev=sda:disk0
before: pvops: disk0=pv xvda + emulated sda
classic: disk0=pv sda + emulated sdq
after: pvops: disk0=pv xvda
classic: disk0=pv sda
vdev=hda:disk0, vdev=sda:disk1
before: pvops: disk0=pv xvda
disk1=emulated sda
classic: disk0=pv hda
disk1=pv sda + emulated sdq
after: pvops: disk0=pv xvda
disk1=not accessible by blkfront, index hda==index sda
classic: disk0=pv hda
disk1=pv sda
vdev=hda:disk0, vdev=sda:disk1, vdev=sdb:disk2
before: pvops: disk0=pv xvda
disk1=emulated sda
disk2=pv xvdb + emulated sdb
classic: disk0=pv hda
disk1=pv sda + emulated sdq
disk2=pv sdb + emulated sdr
after: pvops: disk0=pv xvda
disk1=not accessible by blkfront, index hda==index sda
disk2=pv xvdb
classic: disk0=pv hda
disk1=pv sda
disk2=pv sda
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Stefano Stabellini <sstabellini@kernel.org>
PAGE_SIZE is undefined on ARM64. Use XC_PAGE_SIZE instead, which is
always 4096 even when page granularity is 64K.
For this to actually work with 64K pages, more changes are required.
Signed-off-by: Stefano Stabellini <sstabellini@kernel.org>
Reviewed-by: Juergen Gross <jgross@suse.com>
Release-acked-by: Wei Liu <wei.liu2@citrix.com>
Fix some problems with the tracepoints for ICC register reads
and writes:
* tracepoints for ICC_BPR<n>, ICC_AP<n>R<x>, ICC_IGRPEN<n>,
ICC_EIOR<n> were not printing the <n> that indicated whether
the access was to the group 0 or 1 register
* the ICC_IGREPEN1_EL3 read function was not actually calling
the associated tracepoint
* the ICC_BPR<n> write function was incorrectly calling the
tracepoint for ICC_PMR writes
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1476294876-12340-4-git-send-email-peter.maydell@linaro.org
If a name is provided, the same name is assigned to both the I2C
controllers. Leaving it NULL, causes names to be automatically
assigned with an ID suffix, giving unique names to each
controller. This helps us to uniquely identify each controller in the
device tree, for example when adding an I2C device.
Signed-off-by: Vijay Kumar B. <vijaykumar@zilogic.com>
Reviewed-by: Deepak S. <deepak@zilogic.com>
Message-id: 1476351885-8905-1-git-send-email-vijaykumar@zilogic.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We should avoid exposing new hardware (through DT and ACPI) on older
machine types. This patch keeps 2.7 and older from changing, despite
the introduction of ITS support for 2.8.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 1476117341-32690-3-git-send-email-drjones@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We can't return early from build_* functions, as build_header is
only called at the end.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 1476117341-32690-2-git-send-email-drjones@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Remove unused debugging code to fix native building on aarch64. Without
this change, the following -Werr output inhibits make from completing.
qemu/hw/intc/arm_gic_kvm.c:38:18: error: debug_gic_kvm defined but not used [-Werror=unused-const-variable=]
static const int debug_gic_kvm = 0;
^~~~~~~~~~~~~
cc1: all warnings being treated as errors
qemu/rules.mak:60: recipe for target 'hw/intc/arm_gic_kvm.o' failed
make[1]: *** [hw/intc/arm_gic_kvm.o] Error 1
Makefile:205: recipe for target 'subdir-aarch64-softmmu' failed
Signed-off-by: Christopher Covington <cov@codeaurora.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20161011163202.19720-1-cov@codeaurora.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The M1 and M2 bits are both used for configuring the endianness
of the AHB master interfaces, so the second PL080_CONF_M1 should
be PL080_CONF_M2 instead.
Buglink: https://bugs.launchpad.net/qemu/+bug/1631773
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-id: 1476274451-26567-1-git-send-email-thuth@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When kernel and device tree are specified in the QEMU commandline, then
this device tree may be modified e.g. to add virtio_mmio devices.
With a bootloader e.g. on a flash device these extra devices are not
available.
With this change, the device tree can be specified at the QEMU commandline.
The modified device tree made available to the bootloader with the same
mechanism already supported by device trees fully generated by QEMU.
Signed-off-by: Michael Olbrich <m.olbrich@pengutronix.de>
Message-id: 1473520054-402-1-git-send-email-m.olbrich@pengutronix.de
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The SMC controller on the Aspeed SoC has a set of registers to
configure the mapping of each flash module in the SoC address
space. Writing to these registers triggers a remap of the memory
region and the spec requires a certain number of checks before doing
so.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 1474977462-28032-7-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The SMC controller on the Aspeed SoC has a set of registers to
configure the mapping of each flash module in the SoC address
space. These mapping windows are configurable even though no SPI slave
is attached to the controller.
Also rewrite a bit the comments in the code on this topic.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 1474977462-28032-6-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The SMC controllers on the Aspeed AST2500 SoC are very similar to the
ones found on the AST2400. The differences are on the number of
supported flash modules and their default mappings in the SoC address
space.
The Aspeed AST2500 has one SPI controller for the BMC firmware and two
for the host firmware. All controllers have now the same set of
registers compatible with the AST2400 FMC controller and the legacy
'SMC' controller is fully gone.
We keep the FMC object to act as the BMC SPI controller and add a new
SPI controller for the host. We also have to introduce new type names
to handle the differences in the flash modules memory mappping.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 1474977462-28032-5-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The AST2500 SoC has two. Let's prepare ground for the next changes
which will add the required definitions for the second host SPI
controller.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 1474977462-28032-4-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This will ease the definition of the new controllers for the AST2500
SoC and also ease the support of the segment registers, which provide
a way to reconfigure the mapping window of each slave.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 1474977462-28032-3-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Aspeed SoC has three different types of SMC (Static Memory
Controller) controllers: the SMC (legacy), the FMC (the new one) and
the SPI for the host PNOR. The FMC and the SPI models are now
converging on the AST2500 SoC and the SMC, which was still available
on the AST2400 SoC, was removed.
The Aspeed SoC does not provide support for the legacy SMC
controller. So, let's rename the 'smc' object to 'fmc' to clarify its
nature.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 1474977462-28032-2-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch allocates memory for txbuf in struct Stream rather than the stack.
As a result, the stack frame size is reduced of stream_process_mem2s().
Signed-off-by: Rutuja Shah <rutu.shah.26@gmail.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When doing the conversion, the NULL errp arguments on the
property registration calls were changed to &error_abort.
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Cluster x2APIC cannot work without KVM's x2apic API when the maximal
APIC ID is greater than 8 and only KVM's LAPIC can support x2APIC, so we
forbid other APICs and also the old KVM case with less than 9, to
simplify the code.
There is no point in enabling EIM in forbidden APICs, so we keep it
enabled only for the KVM APIC; unconditionally, because making the
option depend on KVM version would be a maintanance burden.
Old QEMUs would enable eim whenever intremap was on, which would trick
guests into thinking that they can enable cluster x2APIC even if any
interrupt destination would get clamped to 8 bits.
Depending on your configuration, QEMU could notice that the destination
LAPIC is not present and report it with a very non-obvious:
KVM: injection failed, MSI lost (Operation not permitted)
Or the guest could say something about unexpected interrupts, because
clamping leads to aliasing so interrupts were being delivered to
incorrect VCPUs.
KVM_X2APIC_API is the feature that allows us to enable EIM for KVM.
QEMU 2.7 allowed EIM whenever interrupt remapping was enabled. In order
to keep backward compatibility, we again allow guests to misbehave in
non-obvious ways, and make it the default for old machine types.
A user can enable the buggy mode it with "x-buggy-eim=on".
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
The default (auto) emulates the current behavior.
A user can now control EIM like
-device intel-iommu,intremap=on,eim=off
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
* there no point in configuring the device if realization is going to
fail, so move the check to the beginning,
* create a separate function for the check,
* use error_setg() instead error_report().
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
The MMIO interface to APIC only allowed 8 bit addresses, which is not
enough for 32 bit addresses from EIM remapping.
Intel stored upper 24 bits in the high MSI address, so use the same
technique. The technique is also used in KVM MSI interface.
Other APICs are unlikely to handle those upper bits.
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
The MMIO based interface to APIC doesn't work well with MSIs that have
upper address bits set (remapped x2APIC MSIs). A specialized interface
is a quick and dirty way to avoid the shortcoming.
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Every configuration has only up to one APIC class and we'll be extending
the class with a function that can be called without an instanced
object, so a direct access to the class is convenient.
This patch will break compilation if some code uses apic_get_class()
with CONFIG_USER_ONLY.
Suggested-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
When vfio device is reset(encounter FLR, or bus reset), if need to do
bus reset(vfio_pci_hot_reset_one is called), vfio_pci_pre_reset &
vfio_pci_post_reset will be called twice.
Signed-off-by: Cao jin <caoj.fnst@cn.fujitsu.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Introductory comment for rtl8168 VFIO MSI-X quirk states:
At BAR2 offset 0x70 there is a dword data register,
offset 0x74 is a dword address register.
vfio: vfio_bar_read(0000:05:00.0:BAR2+0x70, 4) = 0xfee00398 // read data
Thus, correct offset for data read is 0x70,
but function vfio_rtl8168_quirk_data_read() wrongfully uses offset 0x74.
Signed-off-by: Thorsten Kohfeldt <thorsten.kohfeldt@gmx.de>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
In case the end-user calls qemu with -vfio-pci option without passing
either sysfsdev or host property value, the device is interpreted as
0000:00:00.0. Let's create a specific error message to guide the end-user.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
The returned value (either -errno or -1) is not used anymore by the caller,
vfio_realize, since the error now is stored in the error object. So let's
remove it.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
The returned value is not used anymore by the caller, vfio_realize,
since the error now is stored in the error object. So let's remove it.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
This patch converts VFIO PCI to realize function.
Also original initfn errors now are propagated using QEMU
error objects. All errors are formatted with the same pattern:
"vfio: %s: the error description"
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
This patch propagates errors encountered during vfio_base_device_init
up to the realize function.
In case the host value is not set or badly formed we now report an
error.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
In case the vfio_init_intp fails we currently do not return an
error value. This patch fixes the bug. The returned value is not
explicit but in practice the error object is the one used to
report the error to the end-user and the actual returned error
value is not used.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Propagate the vfio_populate_device errors up to vfio_base_device_init.
The error object also is passed to vfio_init_intp. At the moment we
only report the error. Subsequent patches will propagate the error
up to the realize function.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Pass an error object to prepare for migration to VFIO-PCI realize.
In vfio platform vfio_base_device_init we currently just report the
error. Subsequent patches will propagate the error up to the realize
function.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Pass an error object to prepare for migration to VFIO-PCI realize.
For the time being let's just simply report the error in
vfio platform's vfio_base_device_init(). A subsequent patch will
duly propagate the error up to vfio_platform_realize.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
The error is currently simply reported in vfio_get_group. Don't
bother too much with the prefix which will be handled at upper level,
later on.
Also return an error value in case container->error is not 0 and
the container is teared down.
On vfio_spapr_remove_window failure, we also report an error whereas
it was silent before.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Pass an error object to prepare for migration to VFIO-PCI realize.
In vfio_probe_igd_bar4_quirk, simply report the error.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Pass an error object to prepare for migration to VFIO-PCI realize.
The error is cascaded downto vfio_add_std_cap and then vfio_msi(x)_setup,
vfio_setup_pcie_cap.
vfio_add_ext_cap does not return anything else than 0 so let's transform
it into a void function.
Also use pci_add_capability2 which takes an error object.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Pass an error object to prepare for migration to VFIO-PCI realize.
The error object is propagated down to vfio_intx_enable_kvm().
The three other callers, vfio_intx_enable_kvm(), vfio_msi_disable_common()
and vfio_pci_post_reset() do not propagate the error and simply call
error_reportf_err() with the ERR_PREFIX formatting.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Pass an error object to prepare for migration to VFIO-PCI realize.
The returned value will be removed later on.
We now format an error in case of reading failure for
- the MSIX flags
- the MSIX table,
- the MSIX PBA.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Pass an error object to prepare for migration to VFIO-PCI realize.
The returned value will be removed later on.
The case where error recovery cannot be enabled is not converted into
an error object but directly reported through error_report, as before.
Populating an error instead would cause the future realize function to
fail, which is not wanted.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Pass an error object to prepare for the same operation in
vfio_populate_device. Eventually this contributes to the migration
to VFIO-PCI realize.
We now report an error on vfio_get_region_info failure.
vfio_probe_igd_bar4_quirk is not involved in the migration to realize
and simply calls error_reportf_err.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
To prepare for migration to realize, let's use a local error
object in vfio_initfn. Also let's use the same error prefix for all
error messages.
On top of the 1-1 conversion, we start using a common error prefix for
all error messages. We also introduce a similar warning prefix which will
be used later on.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
- a patch to add a vdc->reset() handler to virtio-9p
- a bunch of patches to fix various memory leaks (thanks to Li Qiang)
- some code cleanups for 9pfs
-----BEGIN PGP SIGNATURE-----
iEYEABECAAYFAlgE59oACgkQAvw66wEB28IrzgCePLq8RVQHvxJKcx9CO1XQaXCE
Dp4AoJm+CDVuaBd+cojoUmwGaLmZG8lb
=8nIw
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/gkurz/tags/for-upstream' into staging
This pull request contains:
- a patch to add a vdc->reset() handler to virtio-9p
- a bunch of patches to fix various memory leaks (thanks to Li Qiang)
- some code cleanups for 9pfs
# gpg: Signature made Mon 17 Oct 2016 16:01:46 BST
# gpg: using DSA key 0x02FC3AEB0101DBC2
# gpg: Good signature from "Greg Kurz <groug@kaod.org>"
# gpg: aka "Greg Kurz <groug@free.fr>"
# gpg: aka "Greg Kurz <gkurz@fr.ibm.com>"
# gpg: aka "Greg Kurz <gkurz@linux.vnet.ibm.com>"
# gpg: aka "Gregory Kurz (Groug) <groug@free.fr>"
# gpg: aka "Gregory Kurz (Cimai Technology) <gkurz@cimai.com>"
# gpg: aka "Gregory Kurz (Meiosys Technology) <gkurz@meiosys.com>"
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 2BD4 3B44 535E C0A7 9894 DBA2 02FC 3AEB 0101 DBC2
* remotes/gkurz/tags/for-upstream:
9pfs: fix memory leak in v9fs_write
9pfs: fix memory leak in v9fs_link
9pfs: fix memory leak in v9fs_xattrcreate
9pfs: fix information leak in xattr read
virtio-9p: add reset handler
9pfs: only free completed request if not flushed
9pfs: drop useless check in pdu_free()
9pfs: use coroutine_fn annotation in hw/9pfs/9p.[ch]
9pfs: use coroutine_fn annotation in hw/9pfs/co*.[ch]
9pfs: fsdev: drop useless extern annotation for functions
9pfs: fix potential host memory leak in v9fs_read
9pfs: allocate space for guest originated empty strings
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
If an error occurs when marshalling the transfer length to the guest, the
v9fs_write() function doesn't free an IO vector, thus leading to a memory
leak. This patch fixes the issue.
Signed-off-by: Li Qiang <liqiang6-s@360.cn>
Reviewed-by: Greg Kurz <groug@kaod.org>
[groug, rephrased the changelog]
Signed-off-by: Greg Kurz <groug@kaod.org>
The v9fs_link() function keeps a reference on the source fid object. This
causes a memory leak since the reference never goes down to 0. This patch
fixes the issue.
Signed-off-by: Li Qiang <liqiang6-s@360.cn>
Reviewed-by: Greg Kurz <groug@kaod.org>
[groug, rephrased the changelog]
Signed-off-by: Greg Kurz <groug@kaod.org>
The 'fs.xattr.value' field in V9fsFidState object doesn't consider the
situation that this field has been allocated previously. Every time, it
will be allocated directly. This leads to a host memory leak issue if
the client sends another Txattrcreate message with the same fid number
before the fid from the previous time got clunked.
Signed-off-by: Li Qiang <liqiang6-s@360.cn>
Reviewed-by: Greg Kurz <groug@kaod.org>
[groug, updated the changelog to indicate how the leak can occur]
Signed-off-by: Greg Kurz <groug@kaod.org>
9pfs uses g_malloc() to allocate the xattr memory space, if the guest
reads this memory before writing to it, this will leak host heap memory
to the guest. This patch avoid this.
Signed-off-by: Li Qiang <liqiang6-s@360.cn>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Greg Kurz <groug@kaod.org>
Virtio devices should implement the VirtIODevice->reset() function to
perform necessary cleanup actions and to bring the device to a quiescent
state.
In the case of the virtio-9p device, this means:
- emptying the list of active PDUs (i.e. draining all in-flight I/O)
- freeing all fids (i.e. close open file descriptors and free memory)
That's what this patch does.
The reset handler first waits for all active PDUs to complete. Since
completion happens in the QEMU global aio context, we just have to
loop around aio_poll() until the active list is empty.
The freeing part involves some actions to be performed on the backend,
like closing file descriptors or flushing extended attributes to the
underlying filesystem. The virtfs_reset() function already does the
job: it calls free_fid() for all open fids not involved in an ongoing
I/O operation. We are sure this is the case since we have drained
the PDU active list.
The current code implements all backend accesses with coroutines, but we
want to stay synchronous on the reset path. We can either change the
current code to be able to run when not in coroutine context, or create
a coroutine context and wait for virtfs_reset() to complete. This patch
goes for the latter because it results in simpler code.
Note that we also need to create a dummy PDU because it is also an API
to pass the FsContext pointer to all backend callbacks.
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
If a PDU has a flush request pending, the current code calls pdu_free()
twice:
1) pdu_complete()->pdu_free() with pdu->cancelled set, which does nothing
2) v9fs_flush()->pdu_free() with pdu->cancelled cleared, which moves the
PDU back to the free list.
This works but it complexifies the logic of pdu_free().
With this patch, pdu_complete() only calls pdu_free() if no flush request
is pending, i.e. qemu_co_queue_next() returns false.
Since pdu_free() is now supposed to be called with pdu->cancelled cleared,
the check in pdu_free() is dropped and replaced by an assertion.
Signed-off-by: Greg Kurz <groug@kaod.org>
All these functions either call the v9fs_co_* functions which have the
coroutine_fn annotation, or pdu_complete() which calls qemu_co_queue_next().
Let's mark them to make it obvious they execute in coroutine context.
Signed-off-by: Greg Kurz <groug@kaod.org>
All these functions use the v9fs_co_run_in_worker() macro, and thus always
call qemu_coroutine_self() and qemu_coroutine_yield().
Let's mark them to make it obvious they execute in coroutine context.
Signed-off-by: Greg Kurz <groug@kaod.org>
In 9pfs read dispatch function, it doesn't free two QEMUIOVector
object thus causing potential memory leak. This patch avoid this.
Signed-off-by: Li Qiang <liqiang6-s@360.cn>
Signed-off-by: Greg Kurz <groug@kaod.org>
If a guest sends an empty string paramater to any 9P operation, the current
code unmarshals it into a V9fsString equal to { .size = 0, .data = NULL }.
This is unfortunate because it can cause NULL pointer dereference to happen
at various locations in the 9pfs code. And we don't want to check str->data
everywhere we pass it to strcmp() or any other function which expects a
dereferenceable pointer.
This patch enforces the allocation of genuine C empty strings instead, so
callers don't have to bother.
Out of all v9fs_iov_vunmarshal() users, only v9fs_xattrwalk() checks if
the returned string is empty. It now uses v9fs_string_size() since
name.data cannot be NULL anymore.
Signed-off-by: Li Qiang <liqiang6-s@360.cn>
[groug, rewritten title and changelog,
fix empty string check in v9fs_xattrwalk()]
Signed-off-by: Greg Kurz <groug@kaod.org>
Currently, the MMIO space for accessing PCI on pseries guests begins at
1 TiB in guest address space. Each PCI host bridge (PHB) has a 64 GiB
chunk of address space in which it places its outbound PIO and 32-bit and
64-bit MMIO windows.
This scheme as several problems:
- It limits guest RAM to 1 TiB (though we have a limited fix for this
now)
- It limits the total MMIO window to 64 GiB. This is not always enough
for some of the large nVidia GPGPU cards
- Putting all the windows into a single 64 GiB area means that naturally
aligning things within there will waste more address space.
In addition there was a miscalculation in some of the defaults, which meant
that the MMIO windows for each PHB actually slightly overran the 64 GiB
region for that PHB. We got away without nasty consequences because
the overrun fit within an unused area at the beginning of the next PHB's
region, but it's not pretty.
This patch implements a new scheme which addresses those problems, and is
also closer to what bare metal hardware and pHyp guests generally use.
Because some guest versions (including most current distro kernels) can't
access PCI MMIO above 64 TiB, we put all the PCI windows between 32 TiB and
64 TiB. This is broken into 1 TiB chunks. The first 1 TiB contains the
PIO (64 kiB) and 32-bit MMIO (2 GiB) windows for all of the PHBs. Each
subsequent TiB chunk contains a naturally aligned 64-bit MMIO window for
one PHB each.
This reduces the number of allowed PHBs (without full manual configuration
of all the windows) from 256 to 31, but this should still be plenty in
practice.
We also change some of the default window sizes for manually configured
PHBs to saner values.
Finally we adjust some tests and libqos so that it correctly uses the new
default locations. Ideally it would parse the device tree given to the
guest, but that's a more complex problem for another time.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
On real hardware, and under pHyp, the PCI host bridges on Power machines
typically advertise two outbound MMIO windows from the guest's physical
memory space to PCI memory space:
- A 32-bit window which maps onto 2GiB..4GiB in the PCI address space
- A 64-bit window which maps onto a large region somewhere high in PCI
address space (traditionally this used an identity mapping from guest
physical address to PCI address, but that's not always the case)
The qemu implementation in spapr-pci-host-bridge, however, only supports a
single outbound MMIO window, however. At least some Linux versions expect
the two windows however, so we arranged this window to map onto the PCI
memory space from 2 GiB..~64 GiB, then advertised it as two contiguous
windows, the "32-bit" window from 2G..4G and the "64-bit" window from
4G..~64G.
This approach means, however, that the 64G window is not naturally aligned.
In turn this limits the size of the largest BAR we can map (which does have
to be naturally aligned) to roughly half of the total window. With some
large nVidia GPGPU cards which have huge memory BARs, this is starting to
be a problem.
This patch adds true support for separate 32-bit and 64-bit outbound MMIO
windows to the spapr-pci-host-bridge implementation, each of which can
be independently configured. The 32-bit window always maps to 2G.. in PCI
space, but the PCI address of the 64-bit window can be configured (it
defaults to the same as the guest physical address).
So as not to break possible existing configurations, as long as a 64-bit
window is not specified, a large single window can be specified. This
will appear the same way to the guest as the old approach, although it's
now implemented by two contiguous memory regions rather than a single one.
For now, this only adds the possibility of 64-bit windows. The default
configuration still uses the legacy mode.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Currently the default PCI host bridge for the 'pseries' machine type is
constructed with its IO windows in the 1TiB..(1TiB + 64GiB) range in
guest memory space. This means that if > 1TiB of guest RAM is specified,
the RAM will collide with the PCI IO windows, causing serious problems.
Problems won't be obvious until guest RAM goes a bit beyond 1TiB, because
there's a little unused space at the bottom of the area reserved for PCI,
but essentially this means that > 1TiB of RAM has never worked with the
pseries machine type.
This patch fixes this by altering the placement of PHBs on large-RAM VMs.
Instead of always placing the first PHB at 1TiB, it is placed at the next
1 TiB boundary after the maximum RAM address.
Technically, this changes behaviour in a migration-breaking way for
existing machines with > 1TiB maximum memory, but since having > 1 TiB
memory was broken anyway, this seems like a reasonable trade-off.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
The 'spapr-pci-host-bridge' represents the virtual PCI host bridge (PHB)
for a PAPR guest. Unlike on x86, it's routine on Power (both bare metal
and PAPR guests) to have numerous independent PHBs, each controlling a
separate PCI domain.
There are two ways of configuring the spapr-pci-host-bridge device: first
it can be done fully manually, specifying the locations and sizes of all
the IO windows. This gives the most control, but is very awkward with 6
mandatory parameters. Alternatively just an "index" can be specified
which essentially selects from an array of predefined PHB locations.
The PHB at index 0 is automatically created as the default PHB.
The current set of default locations causes some problems for guests with
large RAM (> 1 TiB) or PCI devices with very large BARs (e.g. big nVidia
GPGPU cards via VFIO). Obviously, for migration we can only change the
locations on a new machine type, however.
This is awkward, because the placement is currently decided within the
spapr-pci-host-bridge code, so it breaks abstraction to look inside the
machine type version.
So, this patch delegates the "default mode" PHB placement from the
spapr-pci-host-bridge device back to the machine type via a public method
in sPAPRMachineClass. It's still a bit ugly, but it's about the best we
can do.
For now, this just changes where the calculation is done. It doesn't
change the actual location of the host bridges, or any other behaviour.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
The existing implementation remains same and ics-base is introduced. The
type name "ics" is retained, and all the related functions renamed as
ics_simple_*
This will allow different implementations for the source controllers
such as the MSI support of PHB3 on Power8 which uses in-memory state
tables for example.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Nikunj A Dadhania <nikunj@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
[ clg: added ICS_BASE_GET_CLASS and related fixes, based on :
http://patchwork.ozlabs.org/patch/646010/ ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Instead of an array of fixed sized blocks, use a list, as we will need
to have sources with variable number of interrupts. SPAPR only uses
a single entry. Native will create more. If performance becomes an
issue we can add some hashed lookup but for now this will do fine.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[ move the initialization of list to xics_common_initfn,
restore xirr_owner after migration and move restoring to
icp_post_load]
Signed-off-by: Nikunj A Dadhania <nikunj@linux.vnet.ibm.com>
[ clg: removed the icp_post_load() changes from nikunj patchset v3:
http://patchwork.ozlabs.org/patch/646008/ ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Rather than machine instances having backward-compatible option
defaults that need to be repeatedly re-enabled for every new machine
type we introduce, we set the defaults appropriate for newer machine
types, then add code to explicitly disable instance options as needed
to maintain compatibility with older machine types.
Currently pseries-2.5 does not inherit from pseries-2.6 in this
fashion, which is okay at the moment since we do not have any
instance compatibility options for pseries-2.6+ currently.
We will make use of this in future patches though, so fix it here.
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
[dwg: Extended to make 2.7 inherit from 2.8 as well]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Needed to make sure usb redirection is prepared to actually handle the
callback from the usb host adapter. Without this interrupt endpoints
don't work on xhci.
Note: On ehci the usb_wakeup() call only schedules a BH for the actual
work, which hides this bug because the allocation happens before ehci
calls back even without this patch.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Message-id: 1476096313-7730-1-git-send-email-kraxel@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The default DMA offset is set to 3. When the property is not set by
the consumer, the default causes DMA access to be shifted by 3
bytes. In PXA, this results in incorrect DMA access, leading to error
notification in the USB controller driver. A better default would be
0, so that there is no offset, when the consumer does not specify one.
Signed-off-by: Vijay Kumar B. <vijaykumar@zilogic.com>
Reviewed-by: Deepak S. <deepak@zilogic.com>
Message-id: 1475060958-7760-1-git-send-email-vijaykumar@zilogic.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
snprintf return value is *not* the number of chars written into the
buffer, but the number of chars needed. So in case the buffer is too
small you can go alloc a bigger one and try again. But that also means
you can't simply use the return value for the next snprintf call
without checking beforehand that things did actually fit.
Problem is that usb_desc_create_serial didn't perform that check, so a
loooong path string (can happen with deep pci-bridge nesting) results in
the third snprintf call smashing the stack.
Fix this by throwing out all the snpintf calls and use g_strdup_printf
instead.
https://bugzilla.redhat.com/show_bug.cgi?id=1381630
Reported-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-id: 1475659998-22045-1-git-send-email-kraxel@redhat.com
All callsites have a XHCIEPContext pointer anyway, so we can just pass
it directly instead of fiddeling with slotid and epid.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 1474965172-30321-9-git-send-email-kraxel@redhat.com
xiaoqiang zhao