The CPU state parameter is not used, remove it and adjust callers. Now we
can compile ioport.c once for all targets.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Callers must pass ELF machine, byte swapping and symbol LSB clearing
information to ELF loader. A.out loader needs page size information, pass
that too as a parameter.
Extract prototypes to a separate file. Move loader.[ch] and elf_ops.h under hw.
Adjust callers. Also use target_phys_addr_t instead of target_ulong for
addresses: loader addresses aren't virtual.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
The extlh instruction on Alpha currently doesn't work properly.
It's a combination of a cut/paste bug (16 where it should be 32) as well
as a "shift by 64" bug.
Signed-off-by: Vince Weaver <vince@csl.cornell.edu>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
pcm_ops.run_out now takes number of live samples (which will be always
greater than zero) as a second argument, every driver was calling
audio_pcm_hw_get_live_out anyway with exception of fmod which used
audio_pcm_hw_get_live_out2 for no good reason.
Signed-off-by: malc <av1474@comtv.ru>
Well one problem seems to be the rx condition,
... if ((s->ier & UART_IER_RDI) && (s->lsr & UART_LSR_DR))
is not enough to trigger an irq, yet still causes the following
conditions not to be checked anymore at all.
Signed-off-by: Juergen Lock <nox@jelal.kn-bremen.de>
Acked-by: Jan Kiszka <jan.kiszka@web.de>
Acked-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
With this patch applied ide drives (when attached to a pci adapter) can
be created via -device, like this:
-drive if=none,id=mydisk,file=/path/to/disk.img
-device ide-drive,drive=mydisk,bus=ide.0,unit=0
Note that creating a master on ide1 doesn't work that way. That is a
side effect of qemu creating a cdrom automagically even if you don't
ask for it.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
This allows the ide bus being initialized without drives attached
and the drives being attached and initialization later on as
separate step.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Like pci_create_simple() but doesn't call qdev_init(), so one can
set properties before initializing the device.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
The serial ports should be present even if associated with a null device
as some firmware wants to initialize them.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
When creating null devices, there is no way to ensure the unicity of
the labels. Bail out with an error message instead.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Don't call curses_resize() at the end of curses_display_init() as height
and width are not yet defined. It will be called later by code from
vl.c.
This save 250MB of memory when using -curses.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Now that labels must be unique, the chr devices can't be opened anymore
within the serial port code (in case they are not already opened in
vl.c), as they end up with the same label. Instead opened so
non-assigned one directly in vl.c, with a different label.
This make MIPS Malta board emulation working again.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Single-stepping branches on MIPS didn't work right, because the
generation of EXCP_DEBUG happened after the generation of the code to
exit the current TB. That is, given the code:
bne v0,v1,target
nop
...
target:
addu v0,v0,v1
1:
when you single-stepped through the NOP, execution wouldn't actually
halt until you reached the label `1'.
This patch corrects that and also changes single-stepping so that a
branch and its delay slot are executed as one instruction for the
purposes of single-stepping. This behavior is comparable to what other
MIPS tools (e.g. MIPSsim with MDI) do. GDB avoids placing breakpoints
in branch delay slots, so this change doesn't break anything on the GDB
side.
Signed-off-by: Nathan Froyd <froydnj@codesourcery.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Changes:
* added isa bus, hooked up to the system bus. Not sure this is correct,
but 'info pci' lists lists no pci-isa bridge in the machine ...).
* switches the default cpu to one which actually works.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Recent versions of the Linux kernel will not preempt CPU-intensive
tasks unless the clock used by sched_clock() works. On -M versatilepb
that's the 24MHz timer in the system controller. It's a very simple
timer, so implement it.
Signed-off-by: Daniel Jacobowitz <dan@codesourcery.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>