Now that Wake-on-LAN support mode is fully integrated into the driver,
allow an user to query and configure Wake-on-LAN in the driver.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update bcmgenet_suspend() to prepare the hardware for being put into
Wake-on-LAN mode if the device can wakeup the system, and Wake-on-LAN is
enabled. Whether we resume from Wake-on-LAN or not, make sure that
bcmgenet_resume() disables the UniMAC MagicPacket matching mode and puts
the hardware in a state where it can receive all incoming packets.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bcmgenet_wol_resume() will create an unbalanced clock state for the
wol_clk clock pointer since everywhere else in the code, we always call
clk_prepare_enable() and clk_disable_unprepare(). This function also
calls init_umac() which is neither correct nor necessary since
bcmgenet_resume() and bcmgenet_open() already does that.
Finally calling bcmgenet_wol_resume() in bcmgenet_open() is not correct,
since the interface would not have been able to put us in Wake-on-LAN
mode if it was not UP before.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Handle UMAC_IRQ_MPD_R interrupt bit in our workqueue to make sure that
we properly re-configure the GENET adapter from Wake-on-LAN.
bcmgenet_power_up() makes sure that we will not leave the UniMAC
hardware in MagicPacket matching mode, since that would prevent any
other packet from being received.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update bcmgenet_power_{up,down} to handle the case where the adapter has
been suspend respectively resumed from Wake-on-LAN using MagicPackets.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add all the required code to program the GENET hardware to enter
Wake-on-LAN mode and wake using MagicPackets with or without SecureOn
password.
This code is hooked to the build system, but is not yet referenced from
ethtool or the main bcmgenet driver.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Attempt to the request the Wake-on-LAN interrupt bit, and if successful,
advertise wakeup capability instead of doing this unconditionnally.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement suspend/resume callbacks in the GENET driver. This makes sure
that we de-initialize and re-initialize the hardware correctly before
entering suspend and when resuming.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a bunch of helper functions: bcmgenet_netif_start,
bcmgenet_netif_stop and bcmgenet_intr_disable to help reuse code that is
going to be necessary for suspend/resume.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Factor the code touching the UniMAC RX/TX enable bits since we are going
to re-use it for implementing suspend/resume.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Checking for wol_enabled in bcmgenet_close() is bogus, since no other
code places set priv->wol_enabled. Remove that as it will conflict with
the upcoming and functional Wake-on-LAN implementation.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix to return -ENODEV from the no ports enabled error handling
case instead of 0.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following sparse warnings:
net/tipc/socket.c:545:5: warning:
symbol 'tipc_sk_proto_rcv' was not declared. Should it be static?
net/tipc/socket.c:2015:5: warning:
symbol 'tipc_ioctl' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fabian Frederick says:
====================
drivers/net: remove unnecessary break after return
Second patchset after "remove unnecessary break after goto" addressing break redundancy on drivers/net branch
(suggested by Joe Perches)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=80611
Reported-by: David Binderman <dcb314@hotmail.com>
Signed-off-by: Andrey Utkin <andrey.krieger.utkin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains updates for your net-next tree,
they are:
1) Use kvfree() helper function from x_tables, from Eric Dumazet.
2) Remove extra timer from the conntrack ecache extension, use a
workqueue instead to redeliver lost events to userspace instead,
from Florian Westphal.
3) Removal of the ulog targets for ebtables and iptables. The nflog
infrastructure superseded this almost 9 years ago, time to get rid
of this code.
4) Replace the list of loggers by an array now that we can only have
two possible non-overlapping logger flavours, ie. kernel ring buffer
and netlink logging.
5) Move Eric Dumazet's log buffer code to nf_log to reuse it from
all of the supported per-family loggers.
6) Consolidate nf_log_packet() as an unified interface for packet logging.
After this patch, if the struct nf_loginfo is available, it explicitly
selects the logger that is used.
7) Move ip and ip6 logging code from xt_LOG to the corresponding
per-family loggers. Thus, x_tables and nf_tables share the same code
for packet logging.
8) Add generic ARP packet logger, which is used by nf_tables. The
format aims to be consistent with the output of xt_LOG.
9) Add generic bridge packet logger. Again, this is used by nf_tables
and it routes the packets to the real family loggers. As a result,
we get consistent logging format for the bridge family. The ebt_log
logging code has been intentionally left in place not to break
backward compatibility since the logging output differs from xt_LOG.
10) Update nft_log to explicitly request the required family logger when
needed.
11) Finish nft_log so it supports arp, ip, ip6, bridge and inet families.
Allowing selection between netlink and kernel buffer ring logging.
12) Several fixes coming after the netfilter core logging changes spotted
by robots.
13) Use IS_ENABLED() macros whenever possible in the netfilter tree,
from Duan Jiong.
14) Removal of a couple of unnecessary branch before kfree, from Fabian
Frederick.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently it's done silently (from the kernel part), and thus it might be
hard to track the renames from logs.
Add a simple netdev_info() to notify the rename, but only in case the
previous name was valid.
CC: "David S. Miller" <davem@davemloft.net>
CC: Eric Dumazet <edumazet@google.com>
CC: Vlad Yasevich <vyasevic@redhat.com>
CC: stephen hemminger <stephen@networkplumber.org>
CC: Jerry Chu <hkchu@google.com>
CC: Ben Hutchings <bhutchings@solarflare.com>
CC: David Laight <David.Laight@ACULAB.COM>
Signed-off-by: Veaceslav Falico <vfalico@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Veaceslav Falico says:
====================
net: print net_device name/state more often
Currently we use net_device->name only if it's the NETREG_REGISTERED
reg_state, otherwise we return "(unregistered device)".
However, we always populate net_device->name on creation, so it's always
available to us for use. The only caveat is that we might have a name like
"eth%d", in which case we cannot use it as it might change in the future.
Also, the net_device might not be NETREG_UNREGISTERED when the function is
called (_UNINITIALIZED, _UNREGISTERING, _RELEASED, _DUMMY), so it's
misleading.
So, a better way would be to always return the dev->name in netdev_name(),
unless it's in the form of "eth%d" or it's empty, then return
"unnamed net_device". This way we'll always return the name in
NETREG_REGISTERED reg_state, and also return it in other states, when
possible.
Also, to be more verbose on non-NETREG_REGISTERED states, add a function
netdev_reg_state(), which returns a string describing the state, and use it
in netdev_printk()-related functions. If the dev is in NETREG_REGISTERED
state then a void string is regurned and, thus, nothing changes.
After these two patches we'll have the same behaviour in the usual cases,
and more verbose in non-standardad/buggy ones.
v2->v3:
Correct the string for _UNINITIALIZED and warn on a bad reg_state,
per Joe Perches's comments.
v1->v2:
As Tom Gundersen suggested, there might be a case when we have an empty
string as a name for a device, so account this also and return "unnamed
device" for that case too.
====================
Signed-off-by: Veaceslav Falico <vfalico@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This way we'll always know in what status the device is, unless it's
running normally (i.e. NETDEV_REGISTERED).
Also, emit a warning once in case of a bad reg_state.
CC: "David S. Miller" <davem@davemloft.net>
CC: Jason Baron <jbaron@akamai.com>
CC: Eric Dumazet <edumazet@google.com>
CC: Vlad Yasevich <vyasevic@redhat.com>
CC: stephen hemminger <stephen@networkplumber.org>
CC: Jerry Chu <hkchu@google.com>
CC: Ben Hutchings <bhutchings@solarflare.com>
CC: Joe Perches <joe@perches.com>
Signed-off-by: Veaceslav Falico <vfalico@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netdev_name() returns dev->name only when the net_device is in
NETREG_REGISTERED state.
However, dev->name is always populated on creation, so we can easily use
it.
There are two cases when there's no real name - when it's an empty string
or when the name is in form of "eth%d", then netdev_name() returns "unnamed
net_device".
CC: "David S. Miller" <davem@davemloft.net>
CC: Tom Gundersen <teg@jklm.no>
Signed-off-by: Veaceslav Falico <vfalico@gmail.com>
Acked-by: Tom Gundersen <teg@jklm.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli