add_control_with_pfx() in hda_generic.c assumes a shorter name string
for the control element, and this resulted in the truncation of the
long but valid string like "Headphone Surround Switch" in the middle.
This patch aligns the max size to the actual limit of snd_ctl_elem_id,
44.
Cc: <stable@vger.kernel.org> [v3.9+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add two more machines that need quirks for headset mics to work.
Tested-by: Shawn Wang <shawn.wang@canonical.com>
BugLink: https://bugs.launchpad.net/bugs/1195636
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This quirk is needed for the headset mic to work on this Dell
machine.
BugLink: https://bugs.launchpad.net/bugs/1195597
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For adding support for many Roland and Yamaha devices:
* 'full-roland-support' of git://git.alsa-project.org/alsa-kprivate:
ALSA: usb-audio: add quirks for Roland QUAD/OCTO-CAPTURE
ALSA: usb-audio: claim autodetected PCM interfaces all at once
ALSA: usb-audio: remove superfluous Roland quirks
ALSA: usb-audio: add MIDI port names for some Roland devices
ALSA: usb-audio: add support for many Roland/Yamaha devices
ALSA: usb-audio: detect implicit feedback on Roland devices
ALSA: usb-audio: store protocol version in struct audioformat
This patch adds the power-saving control for ALC5505 DSP on some
Realtek codecs.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Tested-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Roland Quad/Octo-Capture devices use some unknown vendor-specific
mechanism to switch sample rates (and to manage other controls). To
prevent the driver from attempting to use any other than the default
44.1 kHz sample rate, use quirks to hide the other alternate settings.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
snd_card_register() registers all devices newly added since the last
call. However, the playback/capture streams are handled as one ALSA
device, so the second /dev device will not be registered if the PCM
streams are added in two steps.
QUIRK_AUTODETECT caused the probe callback to be called once for each
interface, which triggered this problem. Work around this by handling
this like the composite quirk, i.e., autodetecting all other interfaces
that might be used for PCM or MIDI.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Remove all quirks that are no longer needed now that the generic Roland
quirks can handle the vendor-specific descriptors correctly.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Add quirks to detect the various vendor-specific descriptors used by
Roland and Yamaha in most of their recent USB audio and MIDI devices.
Together with the previous patch, this should add audio/MIDI support for
the following USB devices:
- Edirol motion dive .tokyo performance package
- Roland MC-808 Synthesizer
- Roland BK-7m Synthesizer
- Roland VIMA JM-5/8 Synthesizer
- Roland SP-555 Sequencer
- Roland V-Synth GT Synthesizer
- Roland Music Atelier AT-75/100/300/350C/500/800/900/900C Organ
- Edirol V-Mixer M-200i/300/380/400/480/R-1000
- BOSS GT-10B Effects Processor
- Roland Fantom G6/G7/G8 Keyboard
- Cakewalk Sonar V-Studio 20/100/700 Audio Interface
- Roland GW-8 Keyboard
- Roland AX-Synth Keyboard
- Roland JUNO-Di/STAGE/Gi Keyboard
- Roland VB-99 Effects Processor
- Cakewalk UM-2G MIDI Interface
- Roland A-500S Keyboard
- Roland SD-50 Synthesizer
- Roland OCTAPAD SPD-30 Controller
- Roland Lucina AX-09 Synthesizer
- BOSS BR-800 Digital Recorder
- Roland DUO/TRI-CAPTURE (EX) Audio Interface
- BOSS RC-300 Loop Station
- Roland JUPITER-50/80 Keyboard
- Roland R-26 Recorder
- Roland SPD-SX Controller
- BOSS JS-10 Audio Player
- Roland TD-11/15/30 Drum Module
- Roland A-49/88 Keyboard
- Roland INTEGRA-7 Synthesizer
- Roland R-88 Recorder
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
All the Roland/Edirol/BOSS USB audio devices that need implicit feedback
show this unambiguously in their descriptors, so it might be a good idea
to let the driver detect this.
This should make playback work correctly (at least with Jack) with the
following devices:
- BOSS GT-100
- BOSS JS-8 Jam Station
- Edirol M-16DX
- Roland GAIA SH-01
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Instead of reading bInterfaceProtocol from the descriptor whenever it's
needed, store this value in the audioformat structure. Besides
simplifying some code, this will allow us to correctly handle vendor-
specific devices where the descriptors are marked with other values.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Use standard PM state macros PCI_Dx instead of numeric 0/1/2..
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
"idx" is controled by the user and can be a negative offset into the
input_names[] array.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As some of ALC269 quirks use the inverted dmic feature, we need to
call alc_inv_dmic_sync() in the resume callback like in alc_resume(),
too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The stac_resume() is exactly what the default resume code does, so
we don't have to define and use it doubly. Let's cut it off.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Hdmi driver may not receive intrinsic event from gfx side when
it's in runtime suspend mode. There's no ELD info when exit from
runtime suspend. This patch avoid missing ELD info.
Signed-off-by: Wang Xingchao <xingchao.wang@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch is a cleanup to the previous patch "reset hda link during system/
runtime suspend".
In this patch
- azx_enter_link_reset() and azx_exit_link_reset() are defined for entering and
exiting the link reset respectively. azx_link_reset() is no longer used and
replaced by azx_enter_link_reset().
- azx_reset() reuses the above two new functions for a link reset cycle
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Pin's connection list may change dynamically with hot-plug event
on Intel Haswell chip. Users would see connections be "0" in codec#.
when play audio on this pin, software driver choose converter from cache
connections. So add "In-driver connection" info to avoid confuse when
raw connections are different with cache connection.
Signed-off-by: Wang Xingchao <xingchao.wang@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We've got bug report wrt many machines with VT1708 (e.g. IBM POS
machines) showing the broken auto-mute behavior. It turned out that
the problem is that the pin control values of the speaker and line-out
pins are completely ignored. As a workaround, let's use the newly
introduced feature of the generic parser, to control the mute via amp
on pins.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a new flag, auto_mute_via_amp, to determine the behavior of the
headphone / line-out auto-mute. When this flag is set, the generic
driver mutes the speaker and line outputs via the amp mute of each
pin, instead of changing the pin control values.
This is introduced for devices that don't work expectedly with the pin
control values; for example, some devices are known to keep enabling
the speaker outputs no matter which pin control values are set on the
speaker pins.
The driver doesn't check actually whether the pins have the output amp
caps, but assumes that the proper mixer (mute) controls are created on
all these pins. If not the case, you can't use this flag for your
device.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Introduce a new helper function, snd_ctl_sync_vmaster(), which updates
the slave put callbacks forcibly as well as calling the hook. This
will be used in the upcoming patch in HD-audio codec driver for
toggling the mute in vmaster slaves.
Along with the new function, the old snd_ctl_sync_vmaster_hook() is
replaced as a macro calling with the argument hook_only=true.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If all the codecs report ClkStopOK (OK to stop bus clock) after being put to
D3, this patch will reset the HDA link before the controller is put to D3.
So the link will be in reset during system or runtime suspend, the bus clock
stops and the codecs are in D3(ClkStop) state.
This may help to reduce power consumption by dozens of mW on some peripheral
hda codecs.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Replace the leftover CONFIG_SND_SOC_OMAP_HDMI_CODEC in
sound/soc/omap/Kconfig with CONFIG_SND_SOC_HDMI_CODEC, which was
forgotten in the commit bf7c6e6c.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Not a big release subsystem wise, the main changes have been some nice
improvements on the driver side:
- Lots of cleanups and fixes for Blackfin, SGTL5000 and UX500.
- Generalisation of the Bluetooth and HDMI stub drivers.
- New CODEC drivers for SSM2518 and RT5640.
- New machine driver for Tegra CPUs with RT5640.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=gWf9
-----END PGP SIGNATURE-----
Merge tag 'asoc-v3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: Updates for v3.11
Not a big release subsystem wise, the main changes have been some nice
improvements on the driver side:
- Lots of cleanups and fixes for Blackfin, SGTL5000 and UX500.
- Generalisation of the Bluetooth and HDMI stub drivers.
- New CODEC drivers for SSM2518 and RT5640.
- New machine driver for Tegra CPUs with RT5640.
In sound/usb/card.c and sound/usb/misc/ua101.c there are no spaces
between the vendor and the device names, use this style in the other
drivers too.
This also helps keeping consistency when new drivers copies from the
ones already in the mainline tree.
Signed-off-by: Antonio Ospite <ao2@amarulasolutions.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For USB devices it's not necessary to allocate physically contiguous
buffers.
Signed-off-by: Antonio Ospite <ao2@amarulasolutions.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For USB devices it's not necessary to allocate physically contiguous
buffers.
Signed-off-by: Antonio Ospite <ao2@amarulasolutions.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The snd_card_used variable is only read but never written, remove it.
Signed-off-by: Antonio Ospite <ao2@amarulasolutions.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This code is older than git, and I haven't tested it, but if size ==
SIZE_MAX_STATUS then we would write one space past the end of the
rmh->Stat[] array.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Like the X220, this quirk was added to support docking station,
so enable the fixup instead.
According to Jan, the generic parser works equal or better
than the current parser. This was tested under a 3.9 kernel.
Reported-by: Jan Alexander Steffens <jan.steffens@gmail.com>
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some VIA codecs like VT1708S have Mic boost amps in the mic pins but
they aren't exposed in the capability bits. In the past driver code,
we override the pin caps and create mic boost controls forcibly.
While transition to the generic parser, we lost the mic boost controls
although the pin caps are still overridden, because the generic parser
code checks the widget caps, too.
So this patch adds a new helper function to allow the override of the
given widget capability bits, and makes VIA codecs driver to add the
missing input-amp capability bit.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=59861
Cc: <stable@vger.kernel.org> [v3.9+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For Intel Haswell HDMI codecs, the pins choose converter 0 by default.
This would cause conflict when playing audio on unused pins,the pin with
physical device connected would get audio data too.
i.e. Pin 0/1/2 default choose converter 0, pin 1 has HDMI monitor connected.
when play audio on Pin 0 or pin 2, pin 1 could get audio data too.
This patch configure unused pins to choose different converter.
Signed-off-by: Wang Xingchao <xingchao.wang@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When a selection to a converter MUX is changed in hdmi_pcm_open(), it
should be cached so that the given connection can be restored properly
at PM resume. We need just to replace the corresponding
snd_hda_codec_write() call with snd_hda_codec_write_cache().
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix to return -ENOMEM in the kmalloc() error handling
case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Haswell converters maybe in wrong power state before usage.
i.e. only converter 0 is in D0, converter 1/2 are in D3.
When pin choose converter 1/2, there's no audio output, this
cause dependency when playing differnt stream on pins.
AUD_PWRST ConvertorA_Widget_Power_State_Current D0
AUD_PWRST ConvertorA_Widget_Power_State_Requsted D0
AUD_PWRST ConvertorB_Widget_Power_State_Current D3
AUD_PWRST ConvertorB_Widget_Power_State_Requested D3
AUD_PWRST ConvC_Widget_PwrSt_Curr D3
AUD_PWRST ConvC_Widget_PwrSt_Req D3
This patch check converter's power state and set D0 if it's in D3 mode.
Signed-off-by: Wang Xingchao <xingchao.wang@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The refactoring by commit 9040d102 introduced the new function
snd_hda_check_power_state(). This function is supposed to return true
if the state already reached to the target state, but it actually
returns false for that. An utterly stupid typo while copy & paste.
Fortunately this didn't influence on much behavior because powering up
AFG usually powers up the child widgets, too. But the finer power
control must have been broken by this bug.
Cc: <stable@vger.kernel.org> [v3.9+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Takashi Iwai