The ChromeOS EC tunnel I2C bus driver depend on CROS_EC_PROTO but
MFD_CROS_EC select CROS_EC_PROTO instead. Mixing select and depends
on is bad practice as it may lead to circular Kconfig dependencies.
Since the platform device that is matched with the I2C bus driver
is registered by the ChromeOS EC mfd driver, I2C_CROS_EC_TUNNEL
really depends on MFD_CROS_EC. And because this config option
selects CROS_EC_PROTO, that dependency is met as well. So make the
driver to depend on MFD_CROS_EC instead of CROS_EC_PROTO.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add support for the I2C controller found on several NXP devices
including LPC2xxx, LPC178x/7x and LPC18xx/43xx. The controller
is implemented as a state machine and the driver act upon the
state changes when the bus is accessed.
The I2C controller supports master/slave operation, bus
arbitration, programmable clock rate, and speeds up to 1 Mbit/s.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add a basic driver for the Renesas EMEV2 SoC. Based on the driver from
the BSP which was first worked on by Ian, and made ready for upstream by
me.
Signed-off-by: Ian Molton <ian.molton@codethink.co.uk>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Pull i2c updates from Wolfram Sang:
"Highlights:
- new drivers for Mediatek I2C, APM X-Gene, Broadcom Settop
- major updates to at91, davinci
- bugfixes to the mux infrastructure when dealing with the new quirk
mechanism
- more users for the bus recovery feature
- further improvements to the slave framework
Plus the usual bunch of smaller driver and core improvements and
fixes.
There is one patch removing old code from an ARM platform. This has
been acked by the sh_mobile maintainer Simon Horman"
* 'i2c/for-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (48 commits)
i2c: busses: i2c-bcm2835: limits cdiv to allowed values
i2c: sh_mobile: use proper type for timeout
i2c: sh_mobile: use adapter default for timeout
i2c: rcar: use proper type for timeout
i2c: rcar: use adapter default for timeout
i2c: designware: Make sure the device is suspended before disabling runtime PM
i2c: tegra: apply size limit quirk
i2c: tegra: don't advertise SMBUS_QUICK
i2c: octeon: remove unused signal handling
i2c: davinci: Optimize SCL generation
i2c: mux: pca954x: Use __i2c_transfer because of quirks
i2c: mux: Use __i2c_transfer() instead of calling parent's master_xfer()
i2c: use parent adapter quirks in mux
i2c: bcm2835: clear reserved bits in S-Register
ARM: shmobile: r8a7740: remove I2C errata handling
i2c: sh_mobile: add errata workaround
i2c: at91: fix code checker warnings
i2c: busses: xgene-slimpro: fix incorrect __init declation for probe
i2c: davinci: Avoid sending to own address
i2c: davinci: Refactor i2c_davinci_wait_bus_not_busy()
...
The MFD driver should only have the logic to instantiate its child devices
and setup any shared resources that will be used by the subdevices drivers.
The cros_ec MFD is more complex than expected since it also has helpers to
communicate with the EC. So the driver will only get more bigger as other
protocols are supported in the future. So move the communication protocol
helpers to its own driver as drivers/platform/chrome/cros_ec_proto.c.
Suggested-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Adding support for i2c controller driver for Broadcom settop
SoCs.
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
[wsa: removed superfluous owner in platform_driver]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The mediatek SoCs have I2C controller that handle I2C transfer.
This patch include common I2C bus driver.
This driver is compatible with I2C controller on mt65xx/mt81xx.
Signed-off-by: Xudong Chen <xudong.chen@mediatek.com>
Signed-off-by: Liguo Zhang <liguo.zhang@mediatek.com>
Signed-off-by: Eddie Huang <eddie.huang@mediatek.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add SLIMpro I2C device driver on APM X-Gene platform. This I2C
device driver use the SLIMpro Mailbox driver to tunnel message to
the SLIMpro coprocessor to do the work of accessing I2C components.
Signed-off-by: Feng Kan <fkan@apm.com>
Signed-off-by: Hieu Le <hnle@apm.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The GPIO subsystem provides dummy GPIO consumer functions if GPIOLIB is
not enabled. Hence drivers that depend on GPIOLIB, but use GPIO consumer
functionality only, can still be compiled if GPIOLIB is not enabled.
Relax the dependency on GPIOLIB if COMPILE_TEST is enabled, where
appropriate.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add an I2C bus driver i2c-xlp9xx.c to support the I2C block in the
XLP9xx/XLP5xx MIPS SoC. Update Kconfig and Makefile to add the
CONFIG_I2C_XLP9XX option.
Signed-off-by: Subhendu Sekhar Behera <sbehera@broadcom.com>
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Adds the i2c bus controller driver for the Ingenic JZ4780 SoC.
Signed-off-by: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The CX92755 is an SoC in the Conexant Digicolor series. The devicetree binding
document describes the I2C controller on the CX92755 SoC, that is also shared
by some other SoCs in the Digicolor series. The driver adds support.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
[wsa: fixed spaces around operators]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Pull i2c updates from Wolfram Sang:
"Summary:
- legacy PM code removed from the core, there were no users anymore
(thanks to Lars-Peter Clausen)
- new driver for Broadcom iProc
- bigger driver updates for designware, rk3x, cadence, ocores
- a bunch of smaller updates and bugfixes"
* 'i2c/for-3.20' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (31 commits)
i2c: ocores: rework clk code to handle NULL cookie
i2c: designware-baytrail: another fixup for proper Kconfig dependencies
i2c: fix reference to functionality constants definition
i2c: iproc: Add Broadcom iProc I2C Driver
i2c: designware-pci: update Intel copyright line
i2c: ocores: add common clock support
i2c: hix5hd2: add COMPILE_TEST
i2c: clarify comments about the dev_released completion
i2c: ocores: fix clock-frequency binding usage
i2c: tegra: Maintain CPU endianness
i2c: designware-baytrail: use proper Kconfig dependencies
i2c: designware: Do not calculate SCL timing parameters needlessly
i2c: do not try to load modules for of-registered devices
i2c: designware: Add Intel Baytrail PMIC I2C bus support
i2c: designware: Add i2c bus locking support
of: i2c: Add i2c-mux-idle-disconnect DT property to PCA954x mux driver
i2c: designware: use {readl|writel}_relaxed instead of readl/writel
i2c: designware-pci: no need to provide clk_khz
i2c: designware-pci: remove Moorestown support
i2c: imx: whitespace and checkpatch cleanup
...
IOSF_MBI is tristate. Baytrail driver isn't.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: David E. Box <david.e.box@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add initial support to the Broadcom iProc I2C controller found in the
iProc family of SoCs.
The iProc I2C controller has separate internal TX and RX FIFOs, each has
a size of 64 bytes. The iProc I2C controller supports two bus speeds
including standard mode (100kHz) and fast mode (400kHz)
Signed-off-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Reviewed-by: Kevin Cernekee <cernekee@chromium.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Commit 9439eb3ab9 ("asm-generic: io: implement relaxed
accessor macros as conditional wrappers") has added
{read,write}{b,w,l,q}_relaxed to include/asm-generic/io.h.
So COMPILE_TEST can be added.
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Make the slave support depend on CONFIG_I2C_SLAVE. Otherwise it gets
included unconditionally, even when it is not needed.
I2C bus drivers which implement slave support must select
I2C_SLAVE.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
IOSF_MBI depends on PCI, so we should not select it but depend on it.
This ensures also we compile on X86 only, other archs will break because
of an arch specific include. Also depend on ACPI since this driver uses
it.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: David E. Box <david.e.box@linux.intel.com>
This patch implements an I2C bus sharing mechanism between the host and platform
hardware on select Intel BayTrail SoC platforms using the X-Powers AXP288 PMIC.
On these platforms access to the PMIC must be shared with platform hardware. The
hardware unit assumes full control of the I2C bus and the host must request
access through a special semaphore. Hardware control of the bus also makes it
necessary to disable runtime pm to avoid interfering with hardware transactions.
Signed-off-by: David E. Box <david.e.box@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Pull more i2c updates from Wolfram Sang:
"Included are two bugfixes needing some bigger refactoring (sh_mobile:
deferred probe with DMA, mv64xxx: fix offload support) and one
deprecated driver removal I thought would go in via ppc but I
misunderstood. It has a proper ack from BenH"
* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: sh_mobile: fix uninitialized var when debug is enabled
macintosh: therm_pm72: delete deprecated driver
i2c: sh_mobile: I2C_SH_MOBILE should depend on HAS_DMA
i2c: sh_mobile: rework deferred probing
i2c: sh_mobile: refactor DMA setup
i2c: mv64xxx: rework offload support to fix several problems
i2c: mv64xxx: use BIT() macro for register value definitions
The highlight is the series that reworks the idle management on powernv, which
allows us to use deeper idle states on those machines.
There's the fix from Anton for the "BUG at kernel/smpboot.c:134!" problem.
An i2c driver for powernv. This is acked by Wolfram Sang, and he asked that we
take it through the powerpc tree.
A fix for audit from rgb at Red Hat, acked by Paul Moore who is one of the audit
maintainers.
A patch from Ben to export the symbol map of our OPAL firmware as a sysfs file,
so that tools can use it.
Also some CXL fixes, a couple of powerpc perf fixes, a fix for smt-enabled, and
the patch to add __force to get_user() so we can use bitwise types.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=GXdK
-----END PGP SIGNATURE-----
Merge tag 'powerpc-3.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux
Pull second batch of powerpc updates from Michael Ellerman:
"The highlight is the series that reworks the idle management on
powernv, which allows us to use deeper idle states on those machines.
There's the fix from Anton for the "BUG at kernel/smpboot.c:134!"
problem.
An i2c driver for powernv. This is acked by Wolfram Sang, and he
asked that we take it through the powerpc tree.
A fix for audit from rgb at Red Hat, acked by Paul Moore who is one of
the audit maintainers.
A patch from Ben to export the symbol map of our OPAL firmware as a
sysfs file, so that tools can use it.
Also some CXL fixes, a couple of powerpc perf fixes, a fix for
smt-enabled, and the patch to add __force to get_user() so we can use
bitwise types"
* tag 'powerpc-3.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux:
powerpc/powernv: Ignore smt-enabled on Power8 and later
powerpc/uaccess: Allow get_user() with bitwise types
powerpc/powernv: Expose OPAL firmware symbol map
powernv/powerpc: Add winkle support for offline cpus
powernv/cpuidle: Redesign idle states management
powerpc/powernv: Enable Offline CPUs to enter deep idle states
powerpc/powernv: Switch off MMU before entering nap/sleep/rvwinkle mode
i2c: Driver to expose PowerNV platform i2c busses
powerpc: add little endian flag to syscall_get_arch()
power/perf/hv-24x7: Use kmem_cache_free() instead of kfree
powerpc/perf/hv-24x7: Use per-cpu page buffer
cxl: Unmap MMIO regions when detaching a context
cxl: Add timeout to process element commands
cxl: Change contexts_lock to a mutex to fix sleep while atomic bug
powerpc: Secondary CPUs must set cpu_callin_map after setting active and online
If NO_DMA=y:
drivers/built-in.o: In function `sh_mobile_i2c_dma_unmap':
i2c-sh_mobile.c:(.text+0x60de42): undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `sh_mobile_i2c_xfer_dma':
i2c-sh_mobile.c:(.text+0x60df22): undefined reference to `dma_map_single'
i2c-sh_mobile.c:(.text+0x60df2e): undefined reference to `dma_mapping_error'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Pull i2c updates from Wolfram Sang:
"For 3.19, the I2C subsystem has to offer special candy this time.
Right in time for Christmas :)
- I2C slave framework: finally, a generic mechanism for Linux being
an I2C slave (if the bus driver supports that). Docs are still
missing but will come later this cycle, the code is good enough to
go.
- I2C muxes represent their topology in sysfs much more detailed.
This will help users to navigate around much easier.
- irq population of i2c clients is now done at probe time, not device
creation time, to have better support for deferred probing.
- new drivers for Imagination SCB, Amlogic Meson
- DMA support added for Freescale IMX, Renesas SHMobile
- slightly bigger driver updates to OMAP, i801, AT91, and rk3x
(mostly quirk handling, timing updates, and using better kernel
interfaces)
- eeprom driver can now write with byte-access (very slow, but OK to
have)
- and the bunch of smaller fixes, cleanups, ID updates..."
* 'i2c/for-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (56 commits)
i2c: sh_mobile: remove unneeded DMA mask
i2c: rcar: add slave support
i2c: slave-eeprom: add eeprom simulator driver
i2c: core changes for slave support
MAINTAINERS: add I2C dt bindings also to I2C realm
i2c: designware: Fix falling time bindings doc
i2c: davinci: switch to use platform_get_irq
Documentation: i2c: Use PM ops instead of legacy suspend/resume
i2c: sh_mobile: optimize irq entry
i2c: pxa: add support for SCCB devices
omap: i2c: don't check bus state IP rev3.3 and earlier
i2c: s3c2410: Handle i2c sys_cfg register in i2c driver
i2c: rk3x: add Kconfig dependency on COMMON_CLK
i2c: omap: add notes related to i2c multimaster mode
i2c: omap: don't reset controller if Arbitration Lost detected
i2c: omap: implement workaround for handling invalid BB-bit values
i2c: omap: cleanup register definitions
i2c: rk3x: handle dynamic clock rate changes correctly
i2c: at91: enable probe deferring on dma channel request
i2c: at91: remove legacy DMA support
...
The patch exposes the available i2c busses on the PowerNV platform
to the kernel and implements the bus driver to support i2c and
smbus commands.
The driver uses the platform device infrastructure to probe the busses
on the platform and registers them with the i2c driver framework.
Signed-off-by: Neelesh Gupta <neelegup@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Wolfram Sang <wsa@the-dreams.de> (I2C part, excluding the bindings)
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Now that we are using the clk notifier framework we get compile errors
without COMMON_CLK. But the driver fails to probe without COMMON_CLK
anyways, so just add that as a Kconfig dependency.
Signed-off-by: Max Schwarz <max.schwarz@online.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The SCB is present on IMG SoCs other than the META-based TZ1090,
such as the MIPS-based Pistachio SoC. Relax the Kconfig dependency
so that it can be built on any MIPS or META machine.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Acked-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This is a driver for the I2C controller found in Amlogic Meson SoCs.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add support for the IMG I2C Serial Control Bus (SCB) found on the
Pistachio and TZ1090 SoCs.
Reviewed-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: James Hogan <james.hogan@imgtec.com>
[Ezequiel: code cleaning and rebasing]
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch adds support for the Diolan DLN-2 I2C master module. Due
to hardware limitations it does not support SMBUS quick commands.
Information about the USB protocol interface can be found in the
Programmer's Reference Manual [1], see section 6.2.2 for the I2C
master module commands and responses.
[1] https://www.diolan.com/downloads/dln-api-manual.pdf
Signed-off-by: Laurentiu Palcu <laurentiu.palcu@intel.com>
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Reviewed-by: Johan Hovold <johan@kernel.org>
[Lee: Fixed some whitespace issues in Kconfig]
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Pull i2c updates from Wolfram Sang:
"Highlights from the I2C subsystem for 3.18:
- new drivers for Axxia AM55xx, and Hisilicon hix5hd2 SoC.
- designware driver gained AMD support, exynos gained exynos7 support
The rest is usual driver stuff. Hopefully no lowlights this time"
* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: i801: Add Device IDs for Intel Sunrise Point PCH
i2c: hix5hd2: add i2c controller driver
i2c-imx: Disable the clock on probe failure
i2c: designware: Add support for AMD I2C controller
i2c: designware: Rework probe() to get clock a bit later
i2c: designware: Default to fast mode in case of ACPI
i2c: axxia: Add I2C driver for AXM55xx
i2c: exynos: add support for HSI2C module on Exynos7
i2c: mxs: detect No Slave Ack on SELECT in PIO mode
i2c: cros_ec: Remove EC_I2C_FLAG_10BIT
i2c: cros-ec-tunnel: Add of match table
i2c: rcar: remove sign-compare flaw
i2c: ismt: Use minimum descriptor size
i2c: imx: Add arbitration lost check
i2c: rk3x: Remove unlikely() annotations
i2c: rcar: check for no IRQ in rcar_i2c_irq()
i2c: rcar: make rcar_i2c_prepare_msg() *void*
i2c: rcar: simplify check for last message
i2c: designware: add support of platform data to set I2C mode
i2c: designware: add support of I2C standard mode
This patch adds the I2C/SMBus Device IDs for the Intel Sunrise Point PCH.
Signed-off-by: James Ralston <james.d.ralston@intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
I2C drivers for hix5hd2 soc series, including following chipset
Hi3716CV200, Hi3719CV100, Hi3718CV100, Hi3719MV100, Hi3718MV100.
Signed-off-by: Wei Yan <sledge.yanwei@huawei.com>
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
[wsa: folded dt docs into this patch]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add support for AMD version of the DW I2C host controller. The device is
enumerated from ACPI namespace with ACPI ID AMD0010. Because the core
driver needs an input source clock, and this is not an Intel LPSS device
where clocks are provided through drivers/acpi/acpi_lpss.c, we register the
clock ourselves if the clock rate is given in ->driver_data
Signed-off-by: Carl Peng <carlpeng008@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add I2C bus driver for the controller found in the LSI Axxia family SoCs. The
driver implements 10-bit addressing and SMBus transfer modes via emulation
(including SMBus block data read).
Signed-off-by: Anders Berg <anders.berg@avagotech.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The HSI2C module on Exynos7 differs in the transfer status
bits. Transfer status bits were moved to INT_ENABLE and
INT_STATUS registers
This patch adds support for the HSI2C module on Exynos7.
1. Implementes a "hw" field in the variant struct to distinguish
the hardware.
2. Updates the dt-new compatible in dt-binding documenation
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch fix spelling typos found in Kconfig.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
All Exynos5 platforms have HSI2C controllers and are needed by
various IPs connected to the boards based on these SoCs. Thus
select this by default for Exynos5 platforms.
Signed-off-by: Sachin Kamat <sachin.kamat@samsung.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This driver is marked as deprecated since the pre-git era. Any user
left(?) should really have switched to i2c-gpio meanwhile.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Jim Cromie <jim.cromie@gmail.com>
It turned out that the s6000 simply has a designware IP core and should
use the designated driver for it which is way more maintained and
feature complete. There are currently no users in tree, and not even a
toolchain for s6000 seems to be available. So, simply remove this
duplicate. If someone needs assistance in converting to the designware
driver, the i2c list will be there to help.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The P2WI controller looks like an SMBus controller which only supports byte
data transfers. But, it differs from standard SMBus protocol on several
aspects:
- it supports only one slave device, and thus drop the address field
- it adds a parity bit every 8bits of data
- only one read access is required to read a byte (instead of a write
followed by a read access in standard SMBus protocol)
- there's no Ack bit after each byte transfer
This means this bus cannot be used to interface with standard SMBus
devices (the only known device to support this interface is the AXP221
PMIC).
However the P2WI protocol is close enough to SMBus to be integrated in
the I2C subsystem (see this thread [1] for detailed reasons that led to
integrating this driver in the I2C subsystem).
[1] http://www.spinics.net/lists/linux-i2c/msg15066.html
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Driver for the native I2C adapter found in Rockchip RK3xxx SoCs.
Configuration is only possible through devicetree. The driver is
interrupt driven and supports the I2C_M_IGNORE_NAK mangling bit.
Signed-off-by: Max Schwarz <max.schwarz@online.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Pull i2c updates from Wolfram Sang:
"I2C has the following updates for 3.16:
- major cleanups to the rcar and sh_mobile drivers
- removal of nuc900 driver which had a compile error for years
- usual bunch of driver updates, bugfixes and cleanups"
* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (44 commits)
i2c: pca954x: Fix compilation without CONFIG_GPIOLIB
i2c: mux: pca954x: Use the descriptor-based GPIO API
i2c: mpc: insert DR read in i2c_fixup()
i2c: bfin: turn to Resource-managed API in probe function
i2c: Make of_device_id array const
i2c: remove unnecessary OOM messages
i2c: designware-pci: Add Haswell PCI IDs
i2c: designware: Add runtime PM hooks
i2c: designware: Disable device on system suspend
i2c: nuc900: remove driver
i2c: imx: update i2c clock divider for each transaction
i2c: imx: fix the i2c bus hang issue when do repeat restart
i2c: rcar: update copyright and license information
i2c: rcar: janitorial cleanup after refactoring
i2c: rcar: reuse status bits as enable bits
i2c: rcar: remove spinlock
i2c: rcar: refactor status bit handling
i2c: rcar: refactor setting up msg
i2c: rcar: check bus free before first message
i2c: rcar: refactor irq state machine
...
On ARM Chromebooks we have a few devices that are accessed by both the
AP (the main "Application Processor") and the EC (the Embedded
Controller). These are:
* The battery (sbs-battery).
* The power management unit tps65090.
On the original Samsung ARM Chromebook these devices were on an I2C
bus that was shared between the AP and the EC and arbitrated using
some extranal GPIOs (see i2c-arb-gpio-challenge).
The original arbitration scheme worked well enough but had some
downsides:
* It was nonstandard (not using standard I2C multimaster)
* It only worked if the EC-AP communication was I2C
* It was relatively hard to debug problems (hard to tell if i2c issues
were caused by the EC, the AP, or some device on the bus).
On the HP Chromebook 11 the design was changed to:
* The AP/EC comms were still i2c, but the battery/tps65090 were no
longer on the bus used for AP/EC communication. The battery was
exposed to the AP through a limited i2c tunnel and tps65090 was
exposed to the AP through a custom Linux driver.
On the Samsung ARM Chromebook 2 the scheme is changed yet again, now:
* The AP/EC comms are now using SPI for faster speeds.
* The EC's i2c bus is exposed to the AP through a full i2c tunnel.
The upstream "tegra124-venice2" uses the same scheme as the Samsung
ARM Chromebook 2, though it has a different set of components on the
other side of the bus.
This driver supports the scheme used by the Samsung ARM Chromebook 2.
Future patches to this driver could add support for the battery tunnel
on the HP Chromebook 11 (and perhaps could even be used to access
tps65090 on the HP Chromebook 11 instead of using a special driver,
but I haven't researched that enough).
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Arnd said in another patch:
"As far as I can tell, this driver must have produced this
error for as long as it has been merged into the mainline kernel, but
it was never part of the normal build tests:
drivers/i2c/busses/i2c-nuc900.c: In function 'nuc900_i2c_probe':
drivers/i2c/busses/i2c-nuc900.c:601:17: error: request for member
'apbfreq' in something not a structure or union
ret = (i2c->clk.apbfreq)/(pdata->bus_freq * 5) - 1;
^
This is an attempt to get the driver to build and possibly
work correctly, although I do wonder whether we should just
remove it, as it has clearly never worked."
I agree with removing it since nobody showed interest in Arnd's fixup
patch.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: Wan ZongShun <mcuos.com@gmail.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
The i2c-eg20t driver is for a companion chip to the Intel Atom E600
series processors. These are 32-bit x86 processors so the driver is
only needed on X86_32. Add COMPILE_TEST as an alternative, so that the
driver can still be build-tested elsewhere.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Pull i2c updates from Wolfram Sang:
"Here is the pull request from the i2c subsystem. It got a little
delayed because I needed to wait for a dependency to be included
(commit b424080a9e08: "reset: Add optional resets and stubs"). Plus,
I had some email problems. All done now, the highlights are:
- drivers can now deprecate their use of i2c classes. That shouldn't
be used on embedded platforms anyhow and was often blindly
copy&pasted. This mechanism gives users time to switch away and
ultimately boot faster once the use of classes for those drivers is
gone for good.
- new drivers for QUP, Cadence, efm32
- tracepoint support for I2C and SMBus
- bigger cleanups for the mv64xxx, nomadik, and designware drivers
And the usual bugfixes, cleanups, feature additions. Most stuff has
been in linux-next for a while. Just some hot fixes and new drivers
were added a bit more recently."
* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (63 commits)
i2c: cadence: fix Kconfig dependency
i2c: Add driver for Cadence I2C controller
i2c: cadence: Document device tree bindings
Documentation: i2c: improve section about flags mangling the protocol
i2c: qup: use proper type fro clk_freq
i2c: qup: off by ones in qup_i2c_probe()
i2c: efm32: fix binding doc
MAINTAINERS: update I2C web resources
i2c: qup: New bus driver for the Qualcomm QUP I2C controller
i2c: qup: Add device tree bindings information
i2c: i2c-xiic: deprecate class based instantiation
i2c: i2c-sirf: deprecate class based instantiation
i2c: i2c-mv64xxx: deprecate class based instantiation
i2c: i2c-designware-platdrv: deprecate class based instantiation
i2c: i2c-davinci: deprecate class based instantiation
i2c: i2c-bcm2835: deprecate class based instantiation
i2c: mv64xxx: Fix reset controller handling
i2c: omap: fix usage of IS_ERR_VALUE with pm_runtime_get_sync
i2c: efm32: new bus driver
i2c: exynos5: remove unnecessary cast of void pointer
...
Javier Martinez Canillas