The SB800 register reference guide says that the SMBus port selection
bits may not always be in register Smbus0En (0x2c) but could
alternatively be found in register Smbus0Sel (0x2e) depending on the
settings in register Smbus0SelEn (0x2f.) Add support for this
configuration.
The "alternative" register is the only one working for the Bolton
(aka Hudson-2) chipset anyway. I do not have any documentation for
the "kerncz" chipset so we treat it the same as the Bolton for now.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Tested-by: Christian Fetzer <fetzer.ch@gmail.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This change will also make Coverity happy by avoiding a theoretical NULL
pointer dereference; yet another reason is to use the above helper function
to tighten the code and make it more readable.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Tested-by: Laxman Dewangan <ldewangan@nvidia.com>
Make use of ARCH_RENESAS in place of ARCH_SHMOBILE.
This is part of an ongoing process to migrate from ARCH_SHMOBILE to
ARCH_RENESAS the motivation for which being that RENESAS seems to be a more
appropriate name than SHMOBILE for the majority of Renesas ARM based SoCs.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
QUP cores can be attached to a BAM module, which acts as
a dma engine for the QUP core. When DMA with BAM is enabled,
the BAM consumer pipe transmitted data is written to the
output FIFO and the BAM producer pipe received data is read
from the input FIFO.
With BAM capabilities, qup-i2c core can transfer more than
256 bytes, without a 'stop' which is not possible otherwise.
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Tested-by: Archit Taneja <architt@codeaurora.org>
Tested-by: Telkar Nagender <ntelkar@codeaurora.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Starting from Intel Sunrisepoint (Skylake PCH) the iTCO watchdog
resources have been moved to reside under the i801 SMBus host
controller whereas previously they were under the LPC device.
This patch adds Intel lewisburg SMBus support for iTCO device.
It allows to load watchdog dynamically when the hardware is
present.
Fixes: cdc5a3110e ("i2c: i801: add Intel Lewisburg device IDs")
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Alexandra Yates <alexandra.yates@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
The current iProc I2C driver only allows each TX transfer up to 63
bytes (the TX FIFO has a size of 64 bytes, and one byte is reserved
for slave address). This patch enhances the driver to support TX
transfer in each I2C message for up to 65535 bytes (a practical
maximum, since member 'max_write_len' of 'struct i2c_adapter_quirks is
of type 'u16')
This works by loading up the I2C TX FIFO and enabling the TX underrun
interrupt for each burst. After each burst of TX data is finished,
i.e., when the TX FIFO becomes empty, the TX underrun interrupt will be
triggered and another burst of TX data can be loaded into the TX FIFO.
This repeats until all TX data are finished
Signed-off-by: Ray Jui <rjui@broadcom.com>
Tested-by: Icarus Chau <ichau@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Fix typo in the driver from 'I2C_TIMEOUT_MESC' to 'I2C_TIMEOUT_MSEC'
Signed-off-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add COMPILE_TEST for the compilation test coverage.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
If 4GB mode is enabled, we should add 4GB DMA mode support in i2c
driver. Set 4GB mode register to support 4GB mode.
Signed-off-by: Liguo Zhang <liguo.zhang@mediatek.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-by: Yingjoe Chen <yingjoe.chen@mediatek.com>
[wsa: updated commit message]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There can be unnecessary runtime suspend-resume cycle during
i2c-designware-platdrv probe when it registers the I2C adapter device. This
happens because i2c-designware-platdrv is set to initially active platform
device in its probe function and is a parent of I2C adapter.
In that case power.usage_count of i2c-designware device is zero and
pm_runtime_get()/pm_runtime_put() cycle during probe could put it into
runtime suspend. This happens when the i2c_register_adapter() calls the
device_register():
i2c_register_adapter
device_register
device_add
bus_probe_device
device_initial_probe
__device_attach
if (dev->parent) pm_runtime_get_sync(dev->parent)
...
if (dev->parent) pm_runtime_put(dev->parent)
After that the i2c_register_adapter() continues registering I2C slave
devices. In case slave device probe does I2C transfers the parent will
resume again and thus get a needless runtime suspend/resume cycle during
adapter registration.
Prevent this while retaining the runtime PM status of i2c-designware by
only incrementing/decrementing device power usage count during I2C
adapter registration. That makes sure there won't be spurious runtime PM
status changes and lets the driver core to idle the device after probe
finishes.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The i2c-designware-platform module has duplicate module information
when CONFIG_I2C_DESIGNWARE_BAYTRAIL is set. It gets the information
from both i2c-designware-platdrv and i2c-designware-baytrail. The
latter is optional extra code which ends up in the same module so it
should not export module information.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The per adapter bus_lock already projects from concurrent calls to the
master_xfer callback. No need to add a driver internal lock.
Also, rephrase a comment to drop mention of this lock.
Reported-by: Rongrong Zou <zourongrong@gmail.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Commit 5de85b9d57 ("PM / runtime: Re-init runtime PM states at probe
error and driver unbind") introduced pm_runtime_reinit() that is used
to reinitialize PM runtime after -EPROBE_DEFER. This allows shutting
down the device after a failed probe.
However, for drivers using pm_runtime_use_autosuspend() this can cause
a state where suspend callback is never called after -EPROBE_DEFER.
On the following device driver probe, hardware state is different from
the PM runtime state causing omap_device to produce the following
error:
omap_device_enable() called from invalid state 1
And with omap_device and omap hardware being picky for PM, this will
block any deeper idle states in hardware.
The solution is to fix the drivers to follow the PM runtime documentation:
1. For sections of code that needs the device disabled, use
pm_runtime_put_sync_suspend() if pm_runtime_set_autosuspend() has
been set.
2. For driver exit code, use pm_runtime_dont_use_autosuspend() before
pm_runtime_put_sync() if pm_runtime_use_autosuspend() has been
set.
Fixes: 5de85b9d57 ("PM / runtime: Re-init runtime PM states at probe
error and driver unbind")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The definition of i2c_msg says that
"If this is the last message in a group, it is followed by a STOP.
Otherwise it is followed by the next @i2c_msg transaction segment,
beginning with a (repeated) START"
So the expectation is that there is no 'STOP' bit inbetween individual
i2c_msg segments with repeated 'START'. Adding the support for the same.
This is required for some clients like touchscreen which keeps
incrementing counts across individual transfers and 'STOP' bit inbetween
resets the counter, which is not required.
This patch adds the support in non-dma mode.
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Tested-by: Archit Taneja <architt@codeaurora.org>
Tested-by: Telkar Nagender <ntelkar@codeaurora.org>
[wsa: updated commit message]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
QUP from version 2.1.1 onwards, supports a new format of
i2c command tags. Tag codes instructs the controller to
perform a operation like read/write. This new tagging version
supports bam dma and transfers of more than 256 bytes without 'stop'
in between. Adding the support for the same.
For each block a data_write/read tag and data_len tag is added to
the output fifo. For the final block of data write_stop/read_stop
tag is used.
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Tested-by: Archit Taneja <architt@codeaurora.org>
Tested-by: Telkar Nagender <ntelkar@codeaurora.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
qup_wait_writeready waits only on a output fifo empty event.
Change the same function to accept the event and data length
to wait as parameters. This way the same function can be used for
timeouts in other places as well.
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Tested-by: Archit Taneja <architt@codeaurora.org>
Tested-by: Telkar Nagender <ntelkar@codeaurora.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The I2C bus names are supposed to be stable as they can be used by
userspace to uniquely identify a specific I2C bus. So restore the
original names for all legacy (pre-SB800) devices.
For SB800 devices and later, improve the names. "SDA" refers to the
serial data pin of each SMBus port, it's an implementation detail the
user doesn't need to know. Use "port" instead, which is easier to
understand.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Christian Fetzer <fetzer.ch@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This is effectively reapplies the commit b0898fdaff ("i2c: designware-pci: use
IRQF_COND_SUSPEND flag") after the commit d80d134182 ("i2c: designware: Move
common probe code into i2c_dw_probe()"). Original message as follows.
The mentioned flag fixes a warning on Intel Edison board since one of the I2C
controller shares IRQ line with watchdog timer.
Fixes: d80d134182 (i2c: designware: Move common probe code into i2c_dw_probe())
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This closes a race window where I2C device drivers attempt to access
I2C buses which aren't fully initialized yet.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Tested-by: Christian Fetzer <fetzer.ch@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
We need a single mutex for all 4 shared SMBus ports on the SB800. A
per-port mutex doesn't protect us from concurrent access.
In theory the mutex should be per PCI device, however in practice we
know that there's only ever a single instance of the device in a given
system so we can use a global.
Also take the mutex during initialization, as first port may be already
in use when second port is initialized.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Tested-by: Christian Fetzer <fetzer.ch@gmail.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
[wsa: made mutex static]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Pull i2c updates from Wolfram Sang:
"Quite some driver updates:
- piix4 can now handle multiplexed adapters
- brcmstb, xlr, eg20t, designware drivers support more SoCs
- emev2 gained i2c slave support
- img-scb and rcar got bigger refactoring to remove issues
- lots of common driver updates
i2c core changes:
- new quirk flag when an adapter does not support clock stretching,
so clients can be configured to avoid that if possible
- added a helper function to retrieve timing parameters from firmware
(with rcar being the first user)
- "multi-master" DT binding added so drivers can adapt to this
setting (like disabling PM to keep arbitration working)
- RuntimePM for the logical adapter device is now always enabled by
the core to ensure propagation from childs to the parent (the HW
device)
- new macro builtin_i2c_driver to reduce boilerplate"
* 'i2c/for-4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (70 commits)
i2c: create builtin_i2c_driver to avoid registration boilerplate
i2c: imx: fix i2c resource leak with dma transfer
dt-bindings: i2c: eeprom: add another EEPROM device
dt-bindings: move I2C eeprom descriptions to the proper file
i2c: designware: Do not require clock when SSCN and FFCN are provided
DT: i2c: trivial-devices: Add Epson RX8010 and MPL3115
i2c: s3c2410: remove superfluous runtime PM calls
i2c: always enable RuntimePM for the adapter device
i2c: designware: retry transfer on transient failure
i2c: ibm_iic: rename i2c_timings struct due to clash with generic version
i2c: designware: Add support for AMD Seattle I2C
i2c: imx: Remove unneeded comments
i2c: st: use to_platform_device()
i2c: designware: use to_pci_dev()
i2c: brcmstb: Adding support for CM and DSL SoCs
i2c: mediatek: fix i2c multi transfer issue in high speed mode
i2c: imx: improve code readability
i2c: imx: Improve message log when DMA is not used
i2c: imx: add runtime pm support to improve the performance
i2c: imx: init bus recovery info before adding i2c adapter
...
* acpi-soc:
PM / clk: don't leave clocks enabled when driver not bound
i2c: dw: Add APM X-Gene ACPI I2C device support
ACPI / APD: Add APM X-Gene ACPI I2C device support
ACPI / LPSS: change 'does not have' to 'has' in comment
Revert "dmaengine: dw: platform: provide platform data for Intel"
dmaengine: dw: return immediately from IRQ when DMA isn't in use
dmaengine: dw: platform: power on device on shutdown
ACPI / LPSS: override power state for LPSS DMA device
ACPI / LPSS: power on when probe() and otherwise when remove()
ACPI / LPSS: do delay for all LPSS devices when D3->D0
ACPI / LPSS: allow to use specific PM domain during ->probe()
Revert "ACPI / LPSS: allow to use specific PM domain during ->probe()"
device core: add BUS_NOTIFY_DRIVER_NOT_BOUND notification
x86/platform/iosf_mbi: Remove duplicate definitions
Conflicts:
drivers/i2c/busses/i2c-designware-platdrv.c
* device-properties:
device property: avoid allocations of 0 length
device property: the secondary fwnode needs to depend on the primary
device property: add spaces to PROPERTY_ENTRY_STRING macro
include/linux/property.h: fix build issues with gcc-4.4.4
i2c: designware: Convert to use unified device property API
mfd: intel-lpss: Pass HSUART configuration via properties
mfd: intel-lpss: Pass SDA hold time to I2C host controller driver
mfd: intel-lpss: Add support for passing device properties
mfd: core: propagate device properties to sub devices drivers
driver core: Do not overwrite secondary fwnode with NULL if it is set
driver core: platform: Add support for built-in device properties
device property: Take a copy of the property set
device property: Fallback to secondary fwnode if primary misses the property
device property: return -EINVAL when property isn't found in ACPI
device property: improve readability of macros
device property: helper macros for property entry creation
device property: keep single value inplace
device property: refactor built-in properties support
device property: rename helper functions
device property: always check for fwnode type
In i2c_imx_dma_xfer(), when dmaengine_submit() returns error,
the context goto label err_submit and then return. However, the
memory allocated for txdesc has not been freed yet, which
leads to resource leak.
Signed-off-by: Gao Pan <b54642@freescale.com>
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The current driver uses input clock source frequency to calculate
values for [SS|FS]_[HC|LC] registers. However, when booting ACPI, we do not
currently have a good way to provide the frequency information.
Instead, we can leverage the SSCN and FFCN ACPI methods, which can be used
to directly provide these values. So, the clock information should
no longer be required during probing.
However, since clk can be invalid, additional checks must be done where
we are making use of it.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Tested-by: Loc Ho <lho@apm.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
RuntimePM of the adapter device is now taken care of by the core. So, we
can remove these calls.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Set the i2c_adapter retries field to a sensible value. This allows the i2c core
to retry master_xfer() when it returns -EAGAIN. Currently the i2c-designware
driver returns -EAGAIN only on Tx arbitration failure (DW_IC_TX_ARB_LOST).
Reported-by: Rolland Chau <zourongrong@gmail.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Enable APM X-Gene ACPI I2C device support by adding the
corresponding ACPI ID. The platform ACPI APD corresponding
change is required to provide the proper clock frequency input.
Signed-off-by: Loc Ho <lho@apm.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Fixes: e1dba01ca6 ("i2c: add generic routine to parse DT for timing information")
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add device HID AMDI0510 to match the I2C controlers on AMD Seattle platform
Signed-off-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
These multi-lines comments do not follow the standard kernel coding
style. In fact, they are not useful comments, so get rid of them.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use to_pci_dev() instead of open-coding it.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Broadcoms DSL, CM (cable modem)and STB I2C core implementation have
8 data in/out registers that can transfer 8 bytes or 32 bytes max.
Cable and DSL "Peripheral" i2c cores use single byte per data
register and the STB can use 4 byte per data register transfer.
Adding support to take care of this difference. Accordingly added
the compatible string for SoCs using the "Peripheral" I2C block.
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
For mt8173 platform with auto restart support, when doing i2c multi
transfer in high speed, we should ignore the first restart irq after
the master code, otherwise the first transfer will be discarded.
Signed-off-by: Liguo Zhang <liguo.zhang@mediatek.com>
Reviewed-by: Eddie Huang <eddie.huang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Replace of_get_named_gpio_flags with of_get_named_gpio because
the latter has less parameters, which improves code readability.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Gao Pan <b54642@freescale.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
When DMA cannot be used, it is better to state that the I2C controller
will operate in PIO mode.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In our former i2c driver, i2c clk is enabled and disabled in
xfer function, which contributes to power saving. However,
the clk enable process brings a busy wait delay until the core
is stable. As a result, the performance is sacrificed.
To weigh the power consumption and i2c bus performance, runtime
pm is the good solution for it. The clk is enabled when a i2c
transfer starts, and disabled after a specifically defined delay.
If CONFIG_PM is disabled the net result of this patch is that the
clock is never disabled.
Without the patch the test case (many eeprom reads) executes with approx:
real 1m7.735s
user 0m0.488s
sys 0m20.040s
With the patch the same test case (many eeprom reads) executes with approx:
real 0m54.241s
user 0m0.440s
sys 0m5.920s
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Gao Pan <b54642@freescale.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
[wsa: sorted includes]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
During driver probe, i2c_imx_init_recovery_info() must come before
i2c_add_numbered_adapter(), because the get/set_scl() functions
are assigned in i2c_register_adapter() under the conditon that bus
recover_info are initialized. Otherwise, get/set_scl() function
pointers never get assigned.
In such case, when i2c_generic_gpio_recovery() is used for bus recovery,
there will be kernel crash because bri->set_scl is NULL.
The solution to this bug is moving i2c_imx_init_recovery_info() before
i2c_register_adapter().
Signed-off-by: Gao Pan <b54642@freescale.com>
Signed-off-by: Fugang Duan <B38611@freescale.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
In multi master mode, the IP core needs to be always active for
arbitration reasons. Get the config from DT and set up PM depending on
the config.
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
These macros don't really hide complexity, but C idioms. Removing them
makes the code easier to read IMO and make a planned extension easier.
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In version 3.3 of the IP when transaction halt is set, an interrupt
will be generated after each byte of a transfer instead of after
every transfer but before the stop bit.
Due to this behaviour we have to be careful that every time we
release the transaction halt we have to re-enable it straight away
so that we only process a single byte, not doing so will result in
all remaining bytes been processed and a stop bit being issued,
which will prevent us having a repeated start.
This change will have no effect on earlier versions of the IP.
Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: James Hartley <james.hartley@imgtec.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Master halt is issued after each byte of a transaction is processed in
IP version 3.3.
Master halt will stall the bus by holding the SCK line low until the
halt bit in the scb_general_control is cleared.
After the last byte of a transfer is processed we can use the Master
Halt interrupt to facilitate a repeated start transfer without
issuing a stop bit.
Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com>
Reviewed-by: James Hartley <james.hartley@imgtec.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Stop Detected interrupt is triggered when a Stop bit is detected on
the bus, which indicates the end of the current transfer.
When the end of a transfer is indicated by the Stop Detected interrupt,
drain the FIFO and signal completion for the transaction.
Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Now that we are using the transaction halt interrupt to safely control
repeated start transfers, we no longer need to handle the fifo
emptying interrupts.
Handling this interrupt along with Transaction Halt interrupt can
cause erratic behaviour.
Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This commit adds support for the I2C_M_IGNORE_NAK protocol
modification.
Such behaviour can only be implemented in atomic mode. So, if a
transaction contains a message with such flag the drivers
switches to atomic mode. The implementation consists simply in
treating NAKs as ACKs.
Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: James Hartley <james.hartley@imgtec.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
When we also are I2C slave, we need to disable runtime PM because the
address detection mechanism needs to be active all the time. However, we
can reenable runtime PM once the slave instance was unregistered. So,
use pm_runtime_get_sync/put to achieve this, since it has proper
refcounting. pm_runtime_allow/forbid is like a global knob controllable
from userspace which is unsuitable here.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
Until we have proper support to make I2C slave support fully optional,
select it to prevent build errors on randconfigs.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The Sigma Designs variant of this controller has the ability to generate
interrupts. This is controlled using two additional registers, oddly
enough overlapping with the defined but unused HDSTATIM.
This patch adds support for using this feature instead of busy-looping
if an IRQ is specified.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The BYTECNT register holds the transfer size minus one. Setting it to
the correct value removes the need for a dummy read/write at the end of
each transfer. As zero-length transfers are not supported, do not
advertise I2C_FUNC_SMBUS_QUICK.
In other words, this patch makes the driver transfer the number of bytes
requested unless this is zero, which is not supported by the hardware
and is thus refused.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Sigma Designs chips use a variant of this controller with the following
differences:
- The BUSY bit in the STATUS register is inverted
- Bit 8 of the CONFIG register must be set
- The controller can generate interrupts
This patch adds support for the first two of these. It also calculates
and sets the correct clock divisor if a clk is provided. The bus
frequency is optionally speficied in the device tree node.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There is code to divide by "bus_speed" some lines below.
To eliminate the possibility of division by zero, bail out if
"clock-frequency" is specified as zero.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This input clock is used to generate the sampling clock for I2C bus.
If the clock rate is zero, there is something wrong with the clock
driver. Bail out with the appropriate error message in such a case.
It would make it easier to find the root cause of failure.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There is code to divide by "bus_speed" some lines below.
To eliminate the possibility of division by zero, bail out if
"clock-frequency" is specified as zero.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This input clock is used to generate the sampling clock for I2C bus.
If the clock rate is zero, there is something wrong with the clock
driver. Bail out with the appropriate error message in such a case.
It would make it easier to find the root cause of failure.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Switch to the new generic functions. Plain convert, no functionality
added yet.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The probe function is a little bit messy, something here, something
there. Rework it so that there is some order: first init the private
structure, then the adapter, then do HW init. This also allows us to
remove the device argument of the clock calculation function, because it
now can be deduced from the private structure. Also, shorten some lines
where possible. This is a preparation for further refactoring.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
On an hardware shared I2C bus (certain Intel Baytrail SoC platforms) the
runtime PM disable depth keeps increasing over repeated modprobe/rmmod
cycle because pm_runtime_disable() is called without checking should it
be disabled already because of bus sharing.
This hasn't made any other harm than dev->power.disable_depth keeps
increasing but keep it sync by calling pm_runtime_disable() only when
runtime PM is not disabled.
Reported-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Because of some hardware limitation, AMD I2C controller can't
trigger pending interrupt if interrupt status has been changed
after clearing interrupt status bits. Then, I2C will lost
interrupt and IO timeout.
According to hardware design, this patch implements a workaround
to disable i2c controller interrupt and re-enable i2c interrupt
before exiting ISR.
To reduce the performance impacts on other vendors, use unlikely
function to check flag in ISR.
Signed-off-by: Xiangliang Yu <Xiangliang.Yu@amd.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
During driver probe, i2c_imx_init_recovery_info() must come before
i2c_add_numbered_adapter(), because the get/set_scl() functions
are assigned in i2c_register_adapter() under the conditon that bus
recover_info are initialized. Otherwise, get/set_scl() function
pointers never get assigned.
In such case, when i2c_generic_gpio_recovery() is used for bus recovery,
there will be kernel crash because bri->set_scl is NULL.
The solution to this bug is moving i2c_imx_init_recovery_info() before
i2c_register_adapter().
Signed-off-by: Gao Pan <b54642@freescale.com>
Signed-off-by: Fugang Duan <B38611@freescale.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
The read and write opcodes are global for all units on SoC and even across
Intel SoCs. Remove duplication of corresponding constants. At the same time
convert all current users.
No functional change.
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Boon Leong Ong <boon.leong.ong@intel.com>
Acked-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
With ACPI _DSD (introduced in ACPI v5.1) it is now possible to pass device
configuration information from ACPI in addition to DT. In order to support
this, convert the driver to use the unified device property accessors
instead of DT specific.
Change to ordering a bit so that we first try platform data and if that's
not available look from device properties. ACPI *CNT methods are then used
as last resort to override everything else.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Allow the eg20t I2C driver to be built for MIPS platforms, in
preparation for use on the MIPS Boston board.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Set the I2C adapter devices of_node to that of the PCI device, such that
I2C clients may be instantiated via device tree.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The hold field allows to configure the data hold time which can be set
with the help of the generic binding 'i2c-sda-hold-time-ns'. This
feature has been introduced with SAMA5D4 SoC family.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
For platform with auto restart support, between every transfer,
i2c controller will trigger an interrupt and SW need to handle
it to start new transfer. When doing write-then-read transfer,
instead of restart mechanism, using WRRD mode to have controller
send both transfer in one request to reduce latency.
Signed-off-by: Liguo Zhang <liguo.zhang@mediatek.com>
Reviewed-by: Eddie Huang <eddie.huang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The suspended flag is a flag holding the device's PM status.
The runtime framework does that for us.
Use pm_runtime_suspended call instead.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Currently the clocks are enabled at probe and disabled at remove.
Which keeps the clocks enabled even if no transaction is going on.
This patch enables the clocks at the start of transfer and disables
after it.
Also adapts to runtime pm.
converts dev pm to const to silence a checkpatch warning.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
As reported in the links given below. the BCM2835 has a hardware bug in
its i2c module which prevents a correct clock stretching. This patch
adds the I2C_AQ_NO_CLK_STRETCH quirk flag to i2c-bcm2835.
Signed-off-by: Nicola Corna <nicola@corna.info>
[wsa: put the links into the code as comments]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
All protected sections are only called from sleep-able context, so there is
no need to use a spinlock.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Shubhrajyoti Datta <shubhraj@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The simple_strtoul function is marked as obsolete.
This patch replace it by kstrtou8.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Tested-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
I2C controller used in Keystone SoC has an undocumented peculiarity which
results in SDA-SCL margins being dependent on module clock. Driving high
capacity bus near its limits can result in STOP condition sometimes being
understood as REPEATED-START by slaves (or NACK instead of ACK, etc...).
Driving the module with higher clocks increases the margin between SDA and SCL
transitions, making the operations with higher bus rates more robust. Therefore,
target the module clock to 12MHz instead of 7MHz, still staying within
the specification limits.
Before the change STOP timing looked like this on 400kHz:
SDA ----------+ +----
\ /
\ /
+----+
(1)
SCL --+ +------------
\ /
\ /
+----+
(2)
While only point (1) signals STOP, point (2) could be incorrectly recognized as
repeated-START (almost no margin between SDA and SCL transitions).
After the change there is at least 600ns margin measured between SCL fall and
SDA fall during STOP generation:
SDA ------+ +----
\ /
\ /
+----+
SCL --+ +--------
\ /
\ /
+----+
->| |<- 600ns
->| |<- tSUSTO
So called tSUSTO (setup time for STOP condition) is still slightly higher than
600ns, so no problem here.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
According to the datasheets the n factor for dividing the tclk is
2 to the power n on Allwinner SoCs, not 2 to the power n + 1 as it is
on other mv64xxx implementations.
I've contacted Allwinner about this and they have confirmed that the
datasheet is correct.
This commit fixes the clk-divider calculations for Allwinner SoCs
accordingly.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
This patch adds support for port names for the SB800 chipset.
Since the chipset supports a multiplexed main SMBus controller, adding
the channel name to the adapter name is necessary to differentiate the
ports better (for example in sensors output).
Signed-off-by: Christian Fetzer <fetzer.ch@gmail.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The SB800 chipset supports a multiplexed main SMBus controller with
four ports. The multiplexed ports share the same SMBus address and
register set. The port is selected by bits 2:1 of the smb_en register
(0x2C).
Only one port can be active at any point in time therefore a mutex is
needed in order to synchronize access.
Additionally, the commit avoids requesting and releasing the SMBus base
address index region on every multiplexed transfer by moving the
request_region call into piix4_probe.
Tested on HP ProLiant MicroServer G7 N54L (where this patch adds
support to access sensor data from the w83795adg).
Cc: Thomas Brandon <tbrandonau@gmail.com>
Cc: Eddi De Pieri <eddi@depieri.net>
Signed-off-by: Christian Fetzer <fetzer.ch@gmail.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The SB800 chipset supports a multiplexed main SMBus controller with
four ports. Therefore the static variable piix4_main_adapter is
converted into a piix4_main_adapters array that can hold one
i2c_adapter for each multiplexed port.
The auxiliary adapter remains unchanged since it represents the second
(not multiplexed) SMBus controller on the SB800 chipset.
Signed-off-by: Christian Fetzer <fetzer.ch@gmail.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Update the comments to match current behaviour. Shorten some comments.
Update copyrights.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
If we don't clear START generation as soon as possible, it may cause
another message to be generated, e.g. when receiving NACK in address
phase. To keep the race window as small as possible, we clear it right
at the beginning of the interrupt. We don't need any checks since we
always want to stop START and STOP generation on the next occasion after
we started it.
This patch improves the situation but sadly does not completely fix it.
It is still to be researched if we can do better given this HW design.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Due to the HW design, master IRQs are timing critical, so give them
precedence over slave IRQ.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The manual says (55.4.8.6) that HW does automatically send STOP after
NACK was received. My measuerments confirm that.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Setting up new messages was done in process context while handling a
message was in interrupt context. Because of the HW design, this IP core
is sensitive to timing, so the context switches were too expensive. Move
this setup to interrupt context as well.
In my test setup, this fixed the occasional 'data byte sent twice' issue
which a number of people have seen. It also fixes to send REP_START
after a read message which was wrongly send as a STOP + START sequence
before.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
After making sure to reinit the HW and clear interrupts in the timeout
case, we know that interrupts are always disabled in the sections
protected by the spinlock. Thus, we can simply remove it which is a
preparation for further refactoring. While here, rename the timeout
variable to time_left which is way more readable.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
We don't need to init HW before every transfer since we know the HW
state then. HW init at probe time is enough. While here, add setting the
clock register which belongs to init HW. Also, set MDBS bit since not
setting it is prohibited according to the manual.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
When calculating the bus speed, the clock should be on, of course. Most
bootloaders left them on, so this went unnoticed so far.
Move the ioremapping out of this clock-enabled-block and prepare for
adding hw initialization there, too.
Reported-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Pull i2c updates from Wolfram Sang:
- New drivers: UniPhier (with and without FIFO)
- some drivers got some bigger rework: ismt, designware, img-scb (rcar
had to be reverted because issues were showing up just lately)
- ACPI: reworked the device scanning and added support for muxes
... and quite a lot of driver bugfixes and cleanups this time. All
files touched outside of the i2c realm have proper acks.
* 'i2c/for-4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (70 commits)
i2c: rcar: Revert the latest refactoring series
i2c: pnx: remove superfluous assignment
MAINTAINERS: i2c: drop i2c-pnx maintainer
MAINTAINERS: i2c: mark also subdirectories as maintained
i2c: cadence: enable driver for ARM64
i2c: i801: Document Intel DNV and Broxton
i2c: at91: manage unexpected RXRDY flag when starting a transfer
i2c: pnx: Use setup_timer instead of open coding it
i2c: add ACPI support for I2C mux ports
acpi: add acpi_preset_companion() stub
i2c: pxa: Add support for pxa910/988 & new configuration features
i2c: au1550: Convert to devm_kzalloc and devm_ioremap_resource
i2c-dev: Fix I2C_SLAVE ioctl comment
i2c-dev: Fix typo in ioctl name reference
i2c: sirf: tune the divider to make i2c bus freq more accurate
i2c: imx: Use -ENXIO as error in the NACK case
i2c: i801: Add support for Intel Broxton
i2c: i801: Add support for Intel DNV
i2c: mediatek: add i2c resume support
i2c: imx: implement bus recovery
...
The asm-generic changes for 4.4 are mostly a series from Christoph Hellwig
to clean up various abuses of headers in there. The patch to rename the
io-64-nonatomic-*.h headers caused some conflicts with new users, so I
added a workaround that we can remove in the next merge window.
The only other patch is a warning fix from Marek Vasut
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=dQKG
-----END PGP SIGNATURE-----
Merge tag 'asm-generic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull asm-generic cleanups from Arnd Bergmann:
"The asm-generic changes for 4.4 are mostly a series from Christoph
Hellwig to clean up various abuses of headers in there. The patch to
rename the io-64-nonatomic-*.h headers caused some conflicts with new
users, so I added a workaround that we can remove in the next merge
window.
The only other patch is a warning fix from Marek Vasut"
* tag 'asm-generic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
asm-generic: temporarily add back asm-generic/io-64-nonatomic*.h
asm-generic: cmpxchg: avoid warnings from macro-ized cmpxchg() implementations
gpio-mxc: stop including <asm-generic/bug>
n_tracesink: stop including <asm-generic/bug>
n_tracerouter: stop including <asm-generic/bug>
mlx5: stop including <asm-generic/kmap_types.h>
hifn_795x: stop including <asm-generic/kmap_types.h>
drbd: stop including <asm-generic/kmap_types.h>
move count_zeroes.h out of asm-generic
move io-64-nonatomic*.h out of asm-generic
This whole series caused sometimes timeouts and even OOPSes on some
r8a7791 Koelsch boards. We need to understand and fix those first.
Revert "i2c: rcar: clean up after refactoring"
Revert "i2c: rcar: revoke START request early"
Revert "i2c: rcar: check master irqs before slave irqs"
Revert "i2c: rcar: don't issue stop when HW does it automatically"
Revert "i2c: rcar: init new messages in irq"
Revert "i2c: rcar: refactor setup of a msg"
Revert "i2c: rcar: remove spinlock"
Revert "i2c: rcar: remove unused IOERROR state"
Revert "i2c: rcar: rework hw init"
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add missing entries into i2c-i801 documentation and Kconfig about recently
added Intel DNV and Broxton.
Reported-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In some cases, we could start a new i2c transfer with the RXRDY flag
set. It is not a clean state and it leads to print annoying error
messages even if there no real issue. The cause is only having garbage
data in the Receive Holding Register because of a weird behavior of the
RXRDY flag.
Reported-by: Peter Rosin <peda@lysator.liu.se>
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Tested-by: Peter Rosin <peda@lysator.liu.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Fixes: 93563a6a71 ("i2c: at91: fix a race condition when using the DMA controller")
Cc: stable@vger.kernel.org #4.1
Use timer API function setup_timer instead of init_timer to
initialize the timer.
Signed-off-by: Muhammad Falak R Wani <falakreyaz@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Although I2C mux devices are easily enumerated using ACPI (_HID/_CID or
device property compatible string match), enumerating I2C client devices
connected through an I2C mux needs a little extra work.
This change implements a method for describing an I2C device hierarchy that
includes mux devices by using an ACPI Device() for each mux channel along
with an _ADR to set the channel number for the device. See
Documentation/acpi/i2c-muxes.txt for a simple example.
To make this work the ismt, i801, and designware pci/platform devs now
share an ACPI companion with their I2C adapter dev similar to how it's done
in OF. This is done on the assumption that power management functions will
not be called directly on the I2C dev that is sharing the ACPI node.
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Dustin Byford <dustin@cumulusnetworks.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
TWSI_ILCR & TWSI_IWCR registers are used to adjust clock rate
of standard & fast mode in pxa910/988; so this patch adds these two new
entries to "struct pxa_reg_layout" and "struct pxa_i2c".
Signed-off-by: Jett.Zhou <jtzhou@marvell.com>
Signed-off-by: Yi Zhang <yizhang@marvell.com>
Signed-off-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
[wsa: white space fixes]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use devm_* APIs to simplify the code.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Tested-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In prima2 and atlas7, due to some hardware design issue. we
need to adjust the divider ratio a little according to i2c
bus frequency ranges.
Since i2c is open drain interface that allows the slave to
stall the transaction by holding the SCL line at '0', the RTL
implementation is waiting for SCL feedback from the pin after
setting it to High-Z ('1'). This wait adds to the high-time
interval counter few cycles of the input synchronization
(depending on the SCL_FILTER_REG field), and also the time it
takes for the board pull-up resistor to rise the SCL line.
For slow SCL settings these additions are negligible, but they
start to affect the speed when clock is set to faster frequencies.
This patch is based on the actual tests, and it makes SCL more
accurate.
Signed-off-by: Guoying Zhang <Guoying.Zhang@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The driver can not be used on a platform with common clock framework
until clk_prepare/clk_unprepare calls are added, otherwise clk_enable
calls will fail and a WARN is generated.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
According to Documentation/i2c/fault-codes the response to a bus NACK
should be -ENXIO, so fix the error code.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch adds the SMBUS PCI ID of Intel Broxton.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Intel DNV SoC has the same legacy SMBus host controller than Intel
Sunrisepoint PCH. It also has same iTCO watchdog on the bus.
Add DNV PCI ID to the list of supported devices.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
mt65xx i2c controller initial setting will be cleared after system suspend,
so we should init mt65xx i2c controller again when system resume.
Signed-off-by: Liguo Zhang <liguo.zhang@mediatek.com>
Signed-off-by: Eddie Huang <eddie.huang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Implement bus recovery methods for i2c-imx so we can recover from
situations where SCL/SDA are stuck low.
Once i2c bus SCL/SDA are stuck low during transfer, config the i2c
pinctrl to gpio mode by calling pinctrl sleep set function, and then
use GPIO to emulate the i2c protocol to send nine dummy clock to recover
i2c device. After recovery, set i2c pinctrl to default group setting.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Gao Pan <b54642@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add support for on-chip I2C controller used on newer UniPhier SoCs
such as PH1-Pro4, PH1-Pro5, etc. This adapter is equipped with
8-depth TX/RX FIFOs.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add support for on-chip I2C controller used on old UniPhier SoCs
such as PH1-LD4, PH1-sLD8, etc. This adapter is so simple that
it has no FIFO in it.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The patch reverts commit a445900c90 (i2c: designware: Add support for
AMD I2C controller). It never worked anyhow because it did not register
a proper clkdev.
Since kernel 4.1 starts to support APD, there is no need to get freq
from id->driver_data for AMD0010. clkdev is supposed to be already
registered in APD.
So, revert old design and make AMD0010 looks like other ones.
Signed-off-by: Ken Xue <Ken.Xue@amd.com>
Signed-off-by: Xiangliang Yu <Xiangliang.Yu@amd.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In some cases a NACK interrupt may be pending in the Status Register (SR)
as a result of a previous transfer. However at91_do_twi_transfer() did not
read the SR to clear pending interruptions before starting a new transfer.
Hence a NACK interrupt rose as soon as it was enabled again at the I2C
controller level, resulting in a wrong sequence of operations and strange
patterns of behaviour on the I2C bus, such as a clock stretch followed by
a restart of the transfer.
This first issue occurred with both DMA and PIO write transfers.
Also when a NACK error was detected during a PIO write transfer, the
interrupt handler used to wrongly start a new transfer by writing into the
Transmit Holding Register (THR). Then the I2C slave was likely to reply
with a second NACK.
This second issue is fixed in atmel_twi_interrupt() by handling the TXRDY
status bit only if both the TXCOMP and NACK status bits are cleared.
Tested with a at24 eeprom on sama5d36ek board running a linux-4.1-at91
kernel image. Adapted to linux-next.
Reported-by: Peter Rosin <peda@lysator.liu.se>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Tested-by: Peter Rosin <peda@lysator.liu.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Fixes: 93563a6a71 ("i2c: at91: fix a race condition when using the DMA controller")
Cc: stable@vger.kernel.org #4.1
Commit ("i2c: designware: Rename platform driver probe and PM
functions") introduced "'dw_i2c_plat_prepare' undeclared here" and
"'dw_i2c_plat_complete' undeclared here" build errors when
CONFIG_PM_SLEEP is not set.
Fix this by renaming NULL defined dw_i2c_prepare and dw_i2c_complete PM
hooks to dw_i2c_plat_prepare and dw_i2c_plat_complete since this was
obviously missing from the commit.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Commit 00d8689b85 ("i2c: mv64xxx: rework offload support to fix
several problems") completely reworked the offload support, but left a
debugging-related "return false" at the beginning of the
mv64xxx_i2c_can_offload() function. This has the unfortunate consequence
that offloading is in fact never used, which wasn't really the
intention.
This commit fixes that problem by removing the bogus "return false".
Fixes: 00d8689b85 ("i2c: mv64xxx: rework offload support to fix several problems")
Signed-off-by: Hezi Shahmoon <hezi@marvell.com>
[Thomas: reworked commit log and title.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: <stable@vger.kernel.org>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Since commit 4baadb9e05 ("ARM: shmobile: r8a7778: remove obsolete
setup code"), Renesas R-Car SoCs are only supported in generic DT-only
ARM multi-platform builds. The driver doesn't need to use platform data
anymore, hence remove platform data configuration.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
[wsa: removed now unused ret value and cast to proper enum type]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Enable the I2C core for this SoC. It is compitable to Gen2 SoCs, so
reuse the settings.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Enable the I2C core for this SoC. I add a new type because this version
has new features (e.g. DMA) which will be added somewhen later.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This allows using OpenCores I2C controller attached to its host in
native-endian mode with bi-endian CPUs. Example of such system is Xtensa
XTFPGA platform.
Acked-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The i2c-au1550 driver has to program various setup and hold times
for the sda/scl signals by hand. The current values seem to be
working best when the driver is supplied with 50MHz, however on the
DB1300 board 48MHz is the closest we can get to it, and the timings
are a bit too tight for that, leading to the last bit of a transmission
sometimes being swallowed. This manifests itself in wrong readings
of the ne1619 sensor and inability to configure the wm8731 i2s codec.
With the relaxed timings, both the sensor and the i2s codec can now
be accessed more reliably over a wider range of I2C block input
frequencies.
Verified on DB1200, DB1300 and DB1550 boards.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This code is repeated in probe:
i2c_dev->adapter.algo = &tegra_i2c_algo;
Cc: Donglin Peng <pengdonglin137@163.com>
Signed-off-by: Barry Song <21cnbao@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
According to "KeyStone Architecture Inter-IC Control Bus User Guide", fixed
additive part of frequency divisors (referred as "d" in the code and datasheet)
always equals to 6, independent of module clock prescaler.
module clock frequency
master clock frequency = ----------------------
(ICCL + 6) + (ICCH + 6)
It was not the case with original Davinci IP. Introduce new compatible property
"ti,keystone-i2c", which triggers special handling in the driver.
Without this change Keystone-based systems (having 204.8MHz input clock) choose
prescaler 29 (PSC=28). Using d=5 in this case leads to bus bitrate ~353kHz
instead of requested 400kHz. After correction, assuming d=6 bus rate is ~392kHz.
This gives ~11% transfer rate increase.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Tested-by: Hemanth Guruva Reddy <hemanth.guruva_reddy@nokia.com>
Tested-by: Lukasz Gemborowski <lukasz.gemborowski@nokia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Issue the warning in all error paths when unable to register MSI or its
handler.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Propagate actual return code when requesting interrupt fails.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
struct pci_dev already has a flag to track if MSI is enabled or not. Use it
directly.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There is no need to repeat the work that is already done in the PCI driver
core. Remove suspend and resume callbacks.
Note that there is no more calls performed to enable or disable a PCI
device during suspend-resume cycle. Nowadays they seems to be
superfluous. Someone can read more in [1].
[1] https://www.kernel.org/doc/ols/2009/ols2009-pages-319-330.pdf
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
pcim_release() will release any requested region. There is no need to duplicate
this effort in the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
ACPI SSCN/FMCN methods were originally added because then the platform can
provide the most accurate HCNT/LCNT values to the driver. However, this
seems not to be true for Dell Inspiron 7348 where using these causes the
touchpad to fail in boot:
i2c_hid i2c-DLL0675:00: failed to retrieve report from device.
i2c_designware INT3433:00: i2c_dw_handle_tx_abort: lost arbitration
i2c_hid i2c-DLL0675:00: failed to retrieve report from device.
i2c_designware INT3433:00: controller timed out
The values received from ACPI are (in fast mode):
HCNT: 72
LCNT: 160
this translates to following timings (input clock is 100MHz on Broadwell):
tHIGH: 720 ns (spec min 600 ns)
tLOW: 1600 ns (spec min 1300 ns)
Bus period: 2920 ns (assuming 300 ns tf and tr)
Bus speed: 342.5 kHz
Both tHIGH and tLOW are within the I2C specification.
The calculated values when ACPI parameters are not used are (in fast mode):
HCNT: 87
LCNT: 159
which translates to:
tHIGH: 870 ns (spec min 600 ns)
tLOW: 1590 ns (spec min 1300 ns)
Bus period 3060 ns (assuming 300 ns tf and tr)
Bus speed 326.8 kHz
These values are also within the I2C specification.
Since both ACPI and calculated values meet the I2C specification timing
requirements it is hard to say why the touchpad does not function properly
with the ACPI values except that the bus speed is higher in this case (but
still well below the max 400kHz).
Solve this by adding DMI quirk to the driver that disables using ACPI
parameters on this particulare machine.
Reported-by: Pavel Roskin <plroskin@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Pavel Roskin <plroskin@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
The core may register clients attached to this master which may use
funtionality from the master. So, RuntimePM must be enabled before, otherwise
this will fail.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: stable@kernel.org
The core may register clients attached to this master which may use
funtionality from the master. So, RuntimePM must be enabled before, otherwise
this will fail. While here, move drvdata, too.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Kukjin Kim <kgene@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
The core may register clients attached to this master which may use
funtionality from the master. So, RuntimePM must be enabled before, otherwise
this will fail. While here, move drvdata, too.
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
There is some code duplication in i2c-designware-platdrv and
i2c-designware-pcidrv probe functions. What is even worse that duplication
requires i2c_dw_xfer(), i2c_dw_func() and i2c_dw_isr() i2c-designware-core
functions to be exported.
Therefore move common code into new i2c_dw_probe() and make functions above
local to i2c-designware-core.
While merging the code patch does following functional changes:
- I2C Adapter name will be "Synopsys DesignWare I2C adapter". Previously it
was used for platform and ACPI devices but PCI device used
"i2c-designware-pci".
- Using device name for interrupt name. Previous it was platform device name,
ACPI device name or "i2c-designware-pci".
- Error code from devm_request_irq() and i2c_add_numbered_adapter() will be
printed in case of error.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Make it easier to distinguish between i2c-designware-platdrv and
i2c-designware-core functions and to be consistent with
i2c-designware-pcidrv.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
dw_readl() and dw_writel() are not used outside of i2c-designware-core and
they are not exported so make them static and remove their forward
declaration.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
i2c_dw_is_enabled() became unused by the commit be58eda775
("i2c: designware-pci: Cleanup driver power management") and
i2c_dw_enable() by the commit 3a48d1c08f ("i2c: prevent spurious
interrupt on Designware controllers").
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Device must not generate interrupts before registering the interrupt
handler so move i2c_dw_disable_int() before requesting it.
There are no known issues with this. The code has been here since commit
fe20ff5c7e ("i2c-designware: Add support for Designware core behind PCI
devices.").
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There is no need to clear interrupts in i2c_dw_pci_probe() since only place
where interrupts are unmasked is i2c_dw_xfer_init() and there interrupts
are always cleared after commit 2a2d95e9d6 ("i2c: designware: always
clear interrupts before enabling them").
This allows to cleanup the code and replace i2c_dw_clear_int() in
i2c_dw_xfer_init() by direct register read as there are no other callers.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
These are not implementations of default architecture code but helpers
for drivers. Move them to the place they belong to.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Darren Hart <dvhart@linux.intel.com>
Acked-by: Hitoshi Mitake <mitake.hitoshi@lab.ntt.co.jp>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The requested bit rate can be outside the range supported by the driver.
The maximum bit rate this driver supports at the moment is 400Khz.
If the requested bit rate is larger than the maximum supported by the
driver, set the bitrate to the maximum supported before bitrate_khz is
calculated.
Maximum speed supported by the driver can be increased to 1Mhz by
adding support for "fast plus mode" in the future.
Fixes: commit 27bce457d5 ("i2c: img-scb: Add Imagination Technologies I2C SCB driver")
Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: James Hartley <james.hartley@imgtec.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Clear line status and all generated interrupts from the interrupt
status register before starting a transfer, as we may have
unserviced interrupts from previous transfers that might be
handled in the context of the new transfer.
Fixes: commit 27bce457d5 ("i2c: img-scb: Add Imagination Technologies I2C SCB driver")
Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: James Hartley <james.hartley@imgtec.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
i2c->line_status accumulates the line status bits that have been seen
with each interrupt. As we're only interested in that bit from the
current interrupt, refer to line_status (the argument to img_i2c_auto)
instead of i2c->line_status.
Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com>
Reviewed-by: James Hartley <james.hartley@imgtec.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Currently, after determining the minimum value for the High period
(TCKH) the remainder of the internal clock pulses is set as the Low
period (TCKL). This causes the i2c clock duty cycle to be much less
than 50%.
Modify the starting position to TCKH and TCKL at 50% of the internal
clock, and adjusts the TCKH and TCKL values from there should the
minimum value for TCKL not be met. This results in duty cycles closer
to 50%.
Fixes: commit 27bce457d5 ("i2c: img-scb: Add Imagination Technologies I2C SCB driver")
Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: James Hartley <james.hartley@imgtec.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Using % can be slow depending on the architecture.
Using DIV_ROUND_UP is nicer and more efficient way to do it.
Fixes: commit 27bce457d5 ("i2c: img-scb: Add Imagination Technologies I2C SCB driver")
Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: James Hartley <james.hartley@imgtec.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Move scb_wr_rd_fence to before reading from fifo and writing to
fifo to make sure the the first read/write is done after the required
number of cycles.
Fixes: commit 27bce457d5 ("i2c: img-scb: Add Imagination Technologies I2C SCB driver")
Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: James Hartley <james.hartley@imgtec.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The code to read from the master read fifo, and write to the master
write fifo, checks a bit in an SCB register before every byte to
ensure that the fifo is not full (write fifo) or empty (read fifo).
Due to clock domain crossing inside the SCB block the updated value
of this bit is only visible after 2 cycles.
The scb_wr_rd_fence() function does 2 dummy writes (to the read-only
revision register), and it's called before reading from or writing to the
fifos to ensure that subsequent reads of the fifo status bits do not read
stale values.
As the 2 dummy writes are required in all versions of the ip, the version
check is dropped.
Fixes: commit 27bce457d5 ("i2c: img-scb: Add Imagination Technologies I2C SCB driver")
Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: James Hartley <james.hartley@imgtec.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Update the comments to match current behaviour. Shorten some comments.
Update copyrights.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
If we don't clear START generation as soon as possible, it may cause
another message to be generated. To keep the race window as small as
possible, we clear it right at the beginning of the interrupt. We don't
need checking since we always want to stop START and STOP generation on
the next occasion after we started it.
This patch improves the situation but sadly does not completely fix it.
It is still to be researched if we can do better given this HW design.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Due to broken HW design, master IRQs are more timing critical, so give
them precedence over slave IRQ.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The manual says (55.4.8.6) that HW does automatically send STOP after
NACK was received. My measuerments confirm that.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Setting up new messages was done in process context while handling a
message was in interrupt context. Because of the HW design, this IP core
is sensitive to timing, so the context switches were too expensive. Move
this setup to interrupt context as well.
In my test setup, this fixed the occasional 'data byte sent twice' issue
which a number of people have seen. It also fixes to send REP_START
after a read message which was wrongly send as a STOP + START sequence
before.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
We make sure to reinit the HW in the timeout case; then we know that
interrupts are always disabled in the sections protected by the
spinlock. Thus, we can simply remove it which is a preparation for
further refactoring. While here, rename the timeout variable to
time_left which is way more readable.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
We don't need to init HW before every transfer since we know the HW
state then. HW init at probe time is enough. While here, add setting the
clock register which belongs to init HW. Also, set MDBS bit since not
setting it is prohibited according to the manual.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Pull i2c updates from Wolfram Sang:
"Features:
- new drivers: Renesas EMEV2, register based MUX, NXP LPC2xxx
- core: scans DT and assigns wakeup interrupts. no driver changes needed.
- core: some refcouting issues fixed and better API for that
- core: new helper function for best effort block read emulation
- slave framework: proper DT bindings and userspace instantiation
- some bigger work for xiic, pxa, omap drivers
.. and quite a number of smaller driver fixes, cleanups, improvements"
* 'i2c/for-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (65 commits)
i2c: mux: reg Change ioread endianness for readback
i2c: mux: reg: fix compilation warnings
i2c: mux: reg: simplify register size checking
i2c: muxes: fix leaked i2c adapter device node references
i2c: allow specifying separate wakeup interrupt in device tree
of/irq: export of_get_irq_byname()
i2c: xgene-slimpro: dma_mapping_error() doesn't return an error code
i2c: Replace I2C_CROS_EC_TUNNEL dependency
eeprom: at24: use i2c_smbus_read_i2c_block_data_or_emulated
i2c: core: Add support for best effort block read emulation
i2c: lpc2k: add driver
i2c: mux: Add register-based mux i2c-mux-reg
i2c: dt: describe generic bindings
i2c: slave: print warning if slave flag not set
i2c: support 10 bit and slave addresses in sysfs 'new_device'
i2c: take address space into account when checking for used addresses
i2c: apply DT flags when probing
i2c: make address check indpendent from client struct
i2c: rename address check functions
i2c: apply address offset for slaves, too
...
- New Clocksource driver from ST
- New MFD/ACPI/DMA drivers for Intel's Sunrisepoint PCH based platforms
- Add support for Arizona WM8998 and WM1814
- Add support for Dialog Semi DA9062 and DA9063
- Add support for Kontron COMe-bBL6 and COMe-cBW6
- Add support for X-Powers AXP152
- Add support for Atmel, many
- Add support for STMPE, many
- Add support for USB in X-Powers AXP22X
- Core Frameworks
- New Base API to traverse devices and their children in reverse order
- Bug Fixes
- Fix race between runtime-suspend and IRQs
- Obtain platform data form more reliable source
- Fix-ups
- Constifying things
- Variable signage changes
- Kconfig depends|selects changes
- Make use of BIT() macro
- Do not supply .owner attribute in *_driver structures
- MAINTAINERS entries
- Stop using set_irq_flags()
- Start using irq_set_chained_handler_and_data()
- Export DT device ID structures
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=2blS
-----END PGP SIGNATURE-----
Merge tag 'mfd-for-linus-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Device Support:
- New Clocksource driver from ST
- New MFD/ACPI/DMA drivers for Intel's Sunrisepoint PCH based platforms
- Add support for Arizona WM8998 and WM1814
- Add support for Dialog Semi DA9062 and DA9063
- Add support for Kontron COMe-bBL6 and COMe-cBW6
- Add support for X-Powers AXP152
- Add support for Atmel, many
- Add support for STMPE, many
- Add support for USB in X-Powers AXP22X
Core Frameworks:
- New Base API to traverse devices and their children in reverse order
Bug Fixes:
- Fix race between runtime-suspend and IRQs
- Obtain platform data form more reliable source
Fix-ups:
- Constifying things
- Variable signage changes
- Kconfig depends|selects changes
- Make use of BIT() macro
- Do not supply .owner attribute in *_driver structures
- MAINTAINERS entries
- Stop using set_irq_flags()
- Start using irq_set_chained_handler_and_data()
- Export DT device ID structures"
* tag 'mfd-for-linus-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (69 commits)
mfd: jz4740-adc: Init mask cache in generic IRQ chip
mfd: cros_ec: spi: Add OF match table
mfd: stmpe: Add OF match table
mfd: max77686: Split out regulator part from the DT binding
mfd: Add DT binding for Maxim MAX77802 IC
mfd: max77686: Use a generic name for the PMIC node in the example
mfd: max77686: Don't suggest in binding to use a deprecated property
mfd: Add MFD_CROS_EC dependencies
mfd: cros_ec: Remove CROS_EC_PROTO dependency for SPI and I2C drivers
mfd: axp20x: Add a cell for the usb power_supply part of the axp20x PMICs
mfd: axp20x: Add missing registers, and mark more registers volatile
mfd: arizona: Fixup some formatting/white space errors
mfd: wm8994: Fix NULL pointer exception on missing pdata
of: Add vendor prefix for Nuvoton
mfd: mt6397: Implement wake handler and suspend/resume to handle wake up event
mfd: atmel-hlcdc: Add support for new SoCs
mfd: Export OF module alias information in missing drivers
mfd: stw481x: Export I2C module alias information
mfd: da9062: Support for the DA9063 OnKey in the DA9062 core
mfd: max899x: Avoid redundant irq_data lookup
...
The dma_mapping_error() function returns true if there is an error, it
doesn't return an error code. We should return -ENOMEM.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
The ChromeOS EC tunnel I2C bus driver depend on CROS_EC_PROTO but
MFD_CROS_EC select CROS_EC_PROTO instead. Mixing select and depends
on is bad practice as it may lead to circular Kconfig dependencies.
Since the platform device that is matched with the I2C bus driver
is registered by the ChromeOS EC mfd driver, I2C_CROS_EC_TUNNEL
really depends on MFD_CROS_EC. And because this config option
selects CROS_EC_PROTO, that dependency is met as well. So make the
driver to depend on MFD_CROS_EC instead of CROS_EC_PROTO.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add support for the I2C controller found on several NXP devices
including LPC2xxx, LPC178x/7x and LPC18xx/43xx. The controller
is implemented as a state machine and the driver act upon the
state changes when the bus is accessed.
The I2C controller supports master/slave operation, bus
arbitration, programmable clock rate, and speeds up to 1 Mbit/s.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
When occur i2c ack error, i2c controller generate two interrupts,
first is the ack error interrupt, then the complete interrupt.
i2c interrupt handler should keep the two interrupt value, and only
call complete() for the complete interrupt.
Signed-off-by: Liguo Zhang <liguo.zhang@mediatek.com>
Signed-off-by: Eddie Huang <eddie.huang@mediatek.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Reset DMA in hardware init function to avoid unknown hardware state
before do any I2C operation.
Signed-off-by: Liguo Zhang <liguo.zhang@mediatek.com>
Signed-off-by: Eddie Huang <eddie.huang@mediatek.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Starting from Intel Sunrisepoint (Skylake PCH) the iTCO watchdog resources
have been moved to reside under the i801 SMBus host controller whereas
previously they were under the LPC device.
In order to support the iTCO watchdog on newer PCHs we need to create the
platform device here in the SMBus driver and pass all known resources using
platform data.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Minor clean up of indenting, no functional change
Signed-off-by: Colin Ian King <colin.king@canonical.com>
[wsa: squashed two lines into one]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The owner of the adapter is missing, while this driver is tristate.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Printing adapter name is irrelevant from this debug print and makes output
needlessly long. Having already device and functions names printed here is
enough for debugging.
While at it remove extra space from "enabled= 0x" and use "%#x" for
printing "0x" prefixed hexadecimal values.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
[wsa: made it a oneliner]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The mentioned flag fixes a warning on Intel Edison board since one of the I2C
controller shares IRQ line with watchdog timer.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add support for VCT-jig parallel port I2C adapter to i2c-parport.
The adapter schematic can be found here (in the RAR file):
http://remont-aud.net/shop/22/desc/vct-jig-komplekt-dlja-samostojatelnoj-sborki
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cadence 1.0 version has bugs which have been fixed in the cadence 1.4 version.
This patch removes the quirks present in the driver for cadence 1.4 version.
Signed-off-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
[wsa: fixed indentation issues in r1p10_i2c_def]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Tegra I2C controller required to configure the clock divisor
register inside controller to different value based on the clock
speed. The recommended clock divisor for the I2C controller for
standard/fast mode is 0x19 and for fast-mode plus is 0x10.
Add support to configure clock divisor register of I2C controller
based on bus clock rate.
This clock divisor is supported form T114 onwards.
Signed-off-by: Chaitanya Bandi <bandik@nvidia.com>
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Once the new configuration is set on the conifg register of
I2C controller, it is require to update the CONFIG_LOAD register
to transfer the new SW configuration to actual HW internal
registers that would be used in the actual logic.
It is like, SW is programming only shadow registers through
regular configuration and when these load_config bit fields
are set to 1, it causes the regular/shadows registers
configuration transferred to the HW internal active registers.
So SW has to set these bit fields at the end of all regular
registers configuration. And these config_load bits are HW
auto-clear bits. HW clears these bit fields once the register
configuration is moved to HW internal active registers. So SW
has to wait until these bits are auto-cleared before going
for any further programming
This mechanism is supported on T124 and after this SoCs.
Signed-off-by: Chaitanya Bandi <bandik@nvidia.com>
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Patch "i2c: omap: abolish variable name confusion" triggered a
coccinelle warning which we fix here:
drivers/i2c/busses/i2c-omap.c:1333:5-24: pm_runtime_get_sync returns < 0 as error. Unecessary IS_ERR_VALUE at line 1334
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In case of error conditions like Arbitration lost or NACK lets signal
the waiting process.
Handle error cases in the Rx path
Signed-off-by: Shubhrajyoti Datta <shubhraj@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Currently only one interrupt is serviced in the isr.
In case the multiple interrupts happen simultenously we service and ack
only one of them. Check for all the causes in the isr and service them.
Signed-off-by: Shubhrajyoti Datta <shubhraj@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Currently there is no slave mode support in the driver
also in the isr we just ack it and do nothing.
So disable the AAS interrupt.
Signed-off-by: Shubhrajyoti Datta <shubhraj@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Remove the busy loop while waiting for bus busy.
Instead let the processor sleep.
Signed-off-by: Shubhrajyoti Datta <shubhraj@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Currently before every transfer the interrupts are disabled.
So incase the slave nacks in the middle of the transfer the
current transfer is not aborted. Upon enabling the interrupts
conditions like NACK , arbitration lost will not be masked.
Remove the disabling of the interrupts.
Signed-off-by: Shubhrajyoti Datta <shubhraj@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Currently before every transfer the controller is reinitialised.
We are already resetting the controller upon errors so upon every
transfer is a performance kill.
Remove the same.
Signed-off-by: Shubhrajyoti Datta <shubhraj@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The xiic_process is a 154 line code that runs in isr context currently
move it to thread context. Also the name xiic_process suggests that the
intension was to run in process context.
Signed-off-by: Shubhrajyoti Datta <shubhraj@xilinx.com>
[wsa: initialized irqreturn_t to IRQ_NONE instead of IRQ_HANDLED]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Currently the interrupts are disabled at the start of the
isr and enabled at the end of the isr. Remove the same.
In case the slave device NACKs the transaction while in the isr
the transfer will continue and the NACK interrupt will arrive
only after the isr is serviced.
Signed-off-by: Shubhrajyoti Datta <shubhraj@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch cleans up i2c_pxa_probe() function,
- Use devm_ variants wherever
This will clean both probe exit and i2c_pxa_remove() functions
- Check platform resource before parsing any other data from DT/platform
- Use dev_err on failure from i2c_add_numbered_adapter()
- Use pr_info instead of printk for KERN_INFO
Signed-off-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
[wsa: removed unneeded error prinout after devm_ioremap_resource]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Update i2c_pxa_scream_blue_murder() fn to print more information
in case of error.
Also, use dev_err variants instead of printk.
Signed-off-by: Jett.Zhou <jtzhou@marvell.com>
Signed-off-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Cc: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Fix below warning message, coming from 64 bit toolchain.
drivers/i2c/busses/i2c-pxa.c:1237:15:
warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
Signed-off-by: Yipeng Yao <ypyao@marvell.com>
[vaibhav.hiremath@linaro.org: Updated Changelog]
Signed-off-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Cc: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In case of timeout in pio mode of operation return I2C_RETRY.
This behavior will be same as interrupt mode of operation.
Signed-off-by: Shouming Wang <wangshm@marvell.com>
[vaibhav.hiremath@linaro.org: Updated changelog]
Signed-off-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Normally i2c controller works as master, so slave addr is not needed, or
it will impact some slave device (eg. ST NFC chip) i2c accesses, because
it has the same i2c address with controller.
For example,
On the pxa1928 based platform, where PMIC (88pm860) is present @0x30
address on TWSI0 interface, and if we set 0x30 as a slave address in
pxa1928 TWSI0 module, all the transactions towards PMIC would go for toss.
Signed-off-by: Jett.Zhou <jtzhou@marvell.com>
Signed-off-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
During suspend there may still be some i2c access happening, as the
interrupt is shared between multiple drivers.
And if we don't keep i2c irq ON, there may be i2c access timeout if
i2c is in irq mode of operation.
Signed-off-by: Raul Xiong <xjian@marvell.com>
Signed-off-by: Xiaofan Tian <tianxf@marvell.com>
[vaibhav.hiremath@linaro.org: updated Changelog]
Signed-off-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Cc: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add a basic driver for the Renesas EMEV2 SoC. Based on the driver from
the BSP which was first worked on by Ian, and made ready for upstream by
me.
Signed-off-by: Ian Molton <ian.molton@codethink.co.uk>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
we're about to remove the module, so we can't
really schedule a PM transition in the future,
we must wait for it to finish.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
struct device pointers are usually called
dev. Calling our struct omap_i2c_dev pointers
also dev has caused enough confusion.
This is the result of a few simple sed rules
to convert all struct omap_i2c_dev pointers
to be called omap instead.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
there's no need to fetch the platform_device
in order to dereference it back to the dev
pointer to access drvdata, we can use
dev_get_drvdata() instead.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Acked-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Start using pr_fmt and convert all remaining printk to use
pr_* family of macros.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
[wsa: remove print on kzalloc failure]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Now parport is using device model so use dev_* macros instead of printk.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch fix some typos found in a printk message and
MODULE_DESCRIPTION.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
At least on the AM335x, enabling OMAP_I2C_SYSTEST_ST_EN is not enough to
allow direct access to the SCL and SDA pins. In addition to ST_EN, we
need to set the TMODE to 0b11 (Loop back & SDA/SCL IO mode select).
Also, as the reset values of SCL_O and SDA_O are 0 (which means "drive
low level"), we need to set them to 1 (which means "high-impedance") to
avoid unwanted changes on the pins.
As a precaution, reset all these bits to their default values after
recovery is complete.
Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Tested-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Current code returns 0 if fails to read clock-frequency DT property,
fix it. Also add checking return value of clk_prepare_enable and
propagate return value of devm_request_irq.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Here's the big char/misc driver pull request for 4.2-rc1.
Lots of mei, extcon, coresight, uio, mic, and other driver updates in
here. Full details in the shortlog. All of these have been in
linux-next for some time with no reported problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlWNn0gACgkQMUfUDdst+ykCCQCgvdF4F2+Hy9+RATdk22ak1uq1
JDMAoJTf4oyaIEdaiOKfEIWg9MasS42B
=H5wD
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here's the big char/misc driver pull request for 4.2-rc1.
Lots of mei, extcon, coresight, uio, mic, and other driver updates in
here. Full details in the shortlog. All of these have been in
linux-next for some time with no reported problems"
* tag 'char-misc-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (176 commits)
mei: me: wait for power gating exit confirmation
mei: reset flow control on the last client disconnection
MAINTAINERS: mei: add mei_cl_bus.h to maintained file list
misc: sram: sort and clean up included headers
misc: sram: move reserved block logic out of probe function
misc: sram: add private struct device and virt_base members
misc: sram: report correct SRAM pool size
misc: sram: bump error message level on unclean driver unbinding
misc: sram: fix device node reference leak on error
misc: sram: fix enabled clock leak on error path
misc: mic: Fix reported static checker warning
misc: mic: Fix randconfig build error by including errno.h
uio: pruss: Drop depends on ARCH_DAVINCI_DA850 from config
uio: pruss: Add CONFIG_HAS_IOMEM dependence
uio: pruss: Include <linux/sizes.h>
extcon: Redefine the unique id of supported external connectors without 'enum extcon' type
char:xilinx_hwicap:buffer_icap - change 1/0 to true/false for bool type variable in function buffer_icap_set_configuration().
Drivers: hv: vmbus: Allocate ring buffer memory in NUMA aware fashion
parport: check exclusive access before register
w1: use correct lock on error in w1_seq_show()
...
Pull i2c updates from Wolfram Sang:
"Highlights:
- new drivers for Mediatek I2C, APM X-Gene, Broadcom Settop
- major updates to at91, davinci
- bugfixes to the mux infrastructure when dealing with the new quirk
mechanism
- more users for the bus recovery feature
- further improvements to the slave framework
Plus the usual bunch of smaller driver and core improvements and
fixes.
There is one patch removing old code from an ARM platform. This has
been acked by the sh_mobile maintainer Simon Horman"
* 'i2c/for-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (48 commits)
i2c: busses: i2c-bcm2835: limits cdiv to allowed values
i2c: sh_mobile: use proper type for timeout
i2c: sh_mobile: use adapter default for timeout
i2c: rcar: use proper type for timeout
i2c: rcar: use adapter default for timeout
i2c: designware: Make sure the device is suspended before disabling runtime PM
i2c: tegra: apply size limit quirk
i2c: tegra: don't advertise SMBUS_QUICK
i2c: octeon: remove unused signal handling
i2c: davinci: Optimize SCL generation
i2c: mux: pca954x: Use __i2c_transfer because of quirks
i2c: mux: Use __i2c_transfer() instead of calling parent's master_xfer()
i2c: use parent adapter quirks in mux
i2c: bcm2835: clear reserved bits in S-Register
ARM: shmobile: r8a7740: remove I2C errata handling
i2c: sh_mobile: add errata workaround
i2c: at91: fix code checker warnings
i2c: busses: xgene-slimpro: fix incorrect __init declation for probe
i2c: davinci: Avoid sending to own address
i2c: davinci: Refactor i2c_davinci_wait_bus_not_busy()
...
- Fix an error path in the mmc block layer
- Fix PM domain attachment for the SDIO bus
- Add support for driver strength selection
- Increase a delay to let voltage stabilize
- Add support for disabling write-protect detection
- Add facility to support re-tuning
- Re-tune and retry in the recovery path
- Add reset option for SDIO
- Consolidations and clean-ups
MMC host:
- Add Mediatek MMC driver
- Constify platform_device_id for a couple of hosts
- Fix modalias to make module auto-loading work for a couple of hosts
- sdhci: Add support for sdhci-arasan4.9a
- sdhci: Fix low memory corruption
- sdhci: Restore behavior while creating OCR mask
- sdhci: Add a callback to select drive strength
- sdhci: Fix driver type B and D handling
- sdhci: Add support for drive strength selection for SPT
- sdhci: Enable HS400 for some Intel host controllers
- sdhci: Convert to use the new re-tuning facility
- sdhci: Various minor fixes and clean-ups
- dw_mmc: Add support for hi6220
- dw_mmc: Use core to handle absent write protect line
- dw_mmc: Add support to switch voltage
- tmio: Some fixes and modernizations
- sh_mmcif: Improve clock rate calculation
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ofUZ
-----END PGP SIGNATURE-----
Merge tag 'mmc-v4.2' of git://git.linaro.org/people/ulf.hansson/mmc
Pull MMC updates from Ulf Hansson:
"Here are the changes for MMC for v4.2.
MMC core:
- Fix an error path in the mmc block layer
- Fix PM domain attachment for the SDIO bus
- Add support for driver strength selection
- Increase a delay to let voltage stabilize
- Add support for disabling write-protect detection
- Add facility to support re-tuning
- Re-tune and retry in the recovery path
- Add reset option for SDIO
- Consolidations and clean-ups
MMC host:
- Add Mediatek MMC driver
- Constify platform_device_id for a couple of hosts
- Fix modalias to make module auto-loading work for a couple of hosts
- sdhci: Add support for sdhci-arasan4.9a
- sdhci: Fix low memory corruption
- sdhci: Restore behavior while creating OCR mask
- sdhci: Add a callback to select drive strength
- sdhci: Fix driver type B and D handling
- sdhci: Add support for drive strength selection for SPT
- sdhci: Enable HS400 for some Intel host controllers
- sdhci: Convert to use the new re-tuning facility
- sdhci: Various minor fixes and clean-ups
- dw_mmc: Add support for hi6220
- dw_mmc: Use core to handle absent write protect line
- dw_mmc: Add support to switch voltage
- tmio: Some fixes and modernizations
- sh_mmcif: Improve clock rate calculation"
* tag 'mmc-v4.2' of git://git.linaro.org/people/ulf.hansson/mmc: (98 commits)
mmc: queue: prevent soft lockups on PREEMPT=n
mmc: mediatek: Add PM support for MMC driver
mmc: mediatek: Add Mediatek MMC driver
mmc: dt-bindings: add Mediatek MMC bindings
mmc: card: Fixup request missing in mmc_blk_issue_rw_rq
mmc: sdhci: fix low memory corruption
mmc: sdhci-pci: Change AMD SDHCI quirk application scope
i2c-piix4: Use Macro for AMD CZ SMBus device ID
pci_ids: Add AMD KERNCZ device ID support
mmc: queue: use swap() in mmc_queue_thread()
mmc: dw_mmc: insmod followed by rmmod will hung for eMMC
mmc: sdhci: Restore behavior while creating OCR mask
mmc: sdhci-pxav3: fix device wakeup initialization
mmc: core: Attach PM domain prior probing of SDIO func driver
mmc: core: Remove redundant ->power_restore() callback for SD
mmc: core: Remove redundant ->power_restore() callback for MMC
mmc: sdhci-bcm2835: Actually enable the clock
mmc: sdhci-bcm2835: Clean up platform allocations if sdhci init fails.
mmc: sdhci-of-esdhc: enable interrupt mode to detect card
mmc: sdhci-esdhc-imx: add quirk SDHCI_QUIRK2_BROKEN_HS200 for imx6qdl
...
Checks if the cdiv value is in between min (0x2) and max (0xFFFE)
supported values by the bcm2835. If not, it returns -ENODEV.
See page 33/34 of BCM2835-ARM-Peripherals.pdf for the DIV register.
https://www.raspberrypi.org/wp-content/uploads/2012/02/BCM2835-ARM-Peripherals.pdf
Signed-off-by: Silvan Wicki <linux_wi@tinag.ch>
[wsa: resolved a merge conflict]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
5 seconds is a very large timeout, and it is hardcoded. Use the default
timeout from 'struct adapter' which is 1 second. It can also be modified
from userspace for specific workloads via i2c-dev.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
5 seconds is a very large timeout, and it is hardcoded. Use the default
timeout from 'struct adapter' which is 1 second. It can also be modified
from userspace for specific workloads via i2c-dev.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The driver calls pm_runtime_put() right before pm_runtime_disable() in its
->remove() hook to make sure clock is gated etc. However, it turns out that
pm_runtime_put() only calls ->idle() hook without actually suspending
anything. The following pm_runtime_disable() will prevent the driver from
suspending thus leaving it "active".
It is better to suspend the device synchronously to make sure it is
actually suspended before disabling runtime PM from it.
While there, undo call to pm_runtime_use_autosuspend().
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
payload_size is a 12 bit field in the HW register, so add a limit for
this size. That way we gracefully reject the message beforehand instead
of generating an OOPS while transferring. Verified using some older
Tegra2 documentation and a more recent Jetson TK1 board.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
This HW cannot send 0-byte-length messages and the driver discards them.
So, we should not advertise SMBUS_QUICK.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
'commit 2637e5fd23 ("i2c: octeon: Fix i2c fail problem when a process is
terminated by a signal")' removed the wait_event_interruptible_timeout to
prevent half/mixed i2c messages from being sent/recievd but forgot to
drop the signal handling case in the return handling. This just removes
this dead code. While at it the return variable is adjusted to the type
expected.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There are several cases where current clock configuration algorithm produces
not optimal results:
- truncation in "clk" calculation leads to the fact that actual BUS frequency
will be always higher than spec except two exact module frequences 8MHz and
12MHz in the whole 7-12MHz range of permitted frequences
- driver configures SCL HIGH to LOW ratio always 1 to 1 and this doesn't work
well in 400kHz case, namely minimum time of LOW state (according to I2C Spec
2.1) 1.3us will not be fulfilled. HIGH to LOW ratio 1 to 2 would be more
approriate here.
Signed-off-by: Michael Lawnick <michael.lawnick@nokia.com>
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The datasheet mentions on page 31 that the bits 10-31 must be read as
don't care and written as 0.
https://www.raspberrypi.org/wp-content/uploads/2012/02/BCM2835-ARM-Peripherals.pdf
We cannot guarantee that we read bits 10-31 as always 0 (because the
datasheet says read as don't care). We clear the bits with a bitmask to
prevent writing back unknown data at the reserved bits.
Signed-off-by: Silvan Wicki <linux_wi@tinag.ch>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This used to be in platform init code. We want it to do in the driver
now. This is basically a code move and a new compatible added.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Change AMD CZ SMBUS device ID from 0x790b to
use Macro definition
Signed-off-by: Wan ZongShun <Vincent.Wan@amd.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The MFD driver should only have the logic to instantiate its child devices
and setup any shared resources that will be used by the subdevices drivers.
The cros_ec MFD is more complex than expected since it also has helpers to
communicate with the EC. So the driver will only get more bigger as other
protocols are supported in the future. So move the communication protocol
helpers to its own driver as drivers/platform/chrome/cros_ec_proto.c.
Suggested-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Commit 1b84f2a4cd ("mfd: cros_ec: Use fixed size arrays to transfer
data with the EC") modified the struct cros_ec_command fields to not
use pointers for the input and output buffers and use fixed length
arrays instead.
This change was made because the cros_ec ioctl API uses that struct
cros_ec_command to allow user-space to send commands to the EC and
to get data from the EC. So using pointers made the API not 64-bit
safe. Unfortunately this approach was not flexible enough for all
the use-cases since there may be a need to send larger commands
on newer versions of the EC command protocol.
So to avoid to choose a constant length that it may be too big for
most commands and thus wasting memory and CPU cycles on copy from
and to user-space or having a size that is too small for some big
commands, use a zero-length array that is both 64-bit safe and
flexible. The same buffer is used for both output and input data
so the maximum of these values should be used to allocate it.
Suggested-by: Gwendal Grignou <gwendal@chromium.org>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
buf_len is a size_t, so unsigned, but was tested with '<= 0'.
Reported-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Fix section mismatch error during kernel build for xgene_slimpro_i2c_probe
function. It was incorrectly defined with __init declaration.
Signed-off-by: Feng Kan <fkan@apm.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Sending a message to own address locks the controller up in very bizarre state,
it behaves as slave even if MDR register clearly states master. The controller
remains in this state until reset. To avoid unnecessary timeouts simply avoid
sending to own address. The controller cannot do this any way. Also, do not
enable AAS IRQ, as the slave mode is not supported by the driver and the only
possibility to trigger this IRQ is to send to own address.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There are several problems in the function:
- "to_cnt" variable does nothing
- schedule_timeout() call without setting current state does nothing
- "allow_sleep" parameter is not really used
Refactor the function so that it really tries to wait. In case of timeout try
to recover the bus.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Adding support for i2c controller driver for Broadcom settop
SoCs.
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
[wsa: removed superfluous owner in platform_driver]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
When FIFOs are available and enabled, the driver now configures the Atmel
eXtended DMA Controller to perform word accesses instead of byte accesses
when possible.
The actual access width depends on the size of the buffer to transmit.
To enable FIFO support the "atmel,fifo-size" property must be set properly
in the I2C controller node of the device tree.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The probe() function now prints the hardware version of the I2C
controller.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
[wsa: s/version/hw version/] for clarity]
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The alternative command mode was introduced to simplify the transmission
of STOP conditions and to solve timing and latency issues around them.
This mode relies on a new register, the Alternative Command Register,
which must be set at the same time as the Master Mode Register. This new
register was designed to allow simple setup of basic combined transactions
built from up to two unitary transactions.
Indeed, the ACR is split into two areas, which describe one unitary
transaction each. Each area is filled with Data Length 8bit counter, a
Direction and a PEC Request bit. The PEC bit is only used in SMBus mode
and is not supported by this driver yet. Also when using alternative
command mode, the MREAD bit from the Master Mode Register is ignored.
Instead the Direction bits from ACR are used to setup the direction, read
or write, of each unitary transaction. Finally the 8bit counters must
filled with the data length of their respective transaction. Then if only
one transaction is to be used, the data length of the second one must be
set to zero. At the moment, this driver uses only the first transaction.
In addition to MMR and ACR, the Control Register also need to be written
to enable the alternative command mode. That's the purpose of its ACMEN
bit, which stands for Alternative Command Mode Enable.
Note that the alternative command mode is compatible with the use of the
Internal Address Register. So combined transactions for eeprom read are
actually implemented with the Internal Address Register. This register is
written with up to 3 bytes, which are the internal address sent to the
slave through the first write transaction. Then the first area of the ACR
describe the write transaction to follow, which carries the data to be
read from the eeprom. The second area of the ACR is not used so its Data
Length 8bit counter is cleared.
For each byte sent or received by the device, the Data Length 8bit counter
is decremented. When it reaches 0, a STOP condition is automatically sent.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch just fixes typo before applying later patches which will use
register bits with index above 16.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
For TX transactions, the TXCOMP bit in the Status Register is cleared
when the first data is written into the Transmit Holding Register.
In the lines from at91_do_twi_transfer():
at91_twi_write_data_dma(dev);
at91_twi_write(dev, AT91_TWI_IER, AT91_TWI_TXCOMP);
the TXCOMP interrupt may be enabled before the DMA controller has
actually started to write into the THR. In such a case, the TXCOMP bit
is still set into the Status Register so the interrupt is triggered
immediately. The driver understands that a transaction completion has
occurred but this transaction hasn't started yet. Hence the TXCOMP
interrupt is no longer enabled by at91_do_twi_transfer() but instead
by at91_twi_write_data_dma_callback().
Also, the TXCOMP bit in the Status Register in not a clear on read flag
but a snapshot of the transmission state at the time the Status
Register is read.
When a NACK error is dectected by the I2C controller, the TXCOMP, NACK
and TXRDY bits are set together to 1 in the SR. If enabled, the TXCOMP
interrupt is triggered at the same time. Also setting the TXRDY to 1
triggers the DMA controller to write the next data into the THR. Such
a write resets the TXCOMP bit to 0 in the SR. So depending on when the
interrupt handler reads the SR, it may fail to detect the NACK error
if it relies on the TXCOMP bit. The NACK bit and its interrupt should
be used instead.
For RX transactions, the TXCOMP bit in the Status Register is cleared
when the START bit is set into the Control Register. However to unify
the management of the TXCOMP bit when the DMA controller is used, the
TXCOMP interrupt is now enabled by the DMA callbacks for both TX and
RX transfers.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Cc: stable@vger.kernel.org #3.10 and later
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add suspend/resume support to the Broadcom iProc I2C driver
Signed-off-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Commit 1fc2fe204c ("i2c: designware: Add runtime PM hooks") adds
runtime pm support using the same ops for system pm and runtime pm.
When suspend to ram, the i2c host may have been runtime suspended, thus
i2c_dw_disable() hangs.
Previously, I fixed this issue by separating ops for system pm and
runtime pm, then in the system suspend/resume path, runtime pm apis are
used to ensure the device is at correct state.
But as Mika Westerberg pointed out: it sounds a bit silly to resume the
device just because you want to call i2c_dw_disable() for it before
suspending again. He then suggested an elegant solution which keeps the
device runtime suspended during system suspend with the help of
'dev->power.direct_complete'. This patch adopted this solution, and in
fact Mika provided the main code.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use recovery framework and implement bus recovery using "Bus Monitor" register.
Tests show that shortening SDA to GND results in "completion" timeout with
"BUSY" bit still set, so initiate recovery in this case.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The mediatek SoCs have I2C controller that handle I2C transfer.
This patch include common I2C bus driver.
This driver is compatible with I2C controller on mt65xx/mt81xx.
Signed-off-by: Xudong Chen <xudong.chen@mediatek.com>
Signed-off-by: Liguo Zhang <liguo.zhang@mediatek.com>
Signed-off-by: Eddie Huang <eddie.huang@mediatek.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Modify i2c-parport driver to use the new parallel port device model.
Tested-by: Jean Delvare <jdelvare@suse.de>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As of now i2c-parport was connecting to all the available parallel
ports. Lets limit that to maximum of 4 instances and at the same time
define which instance connects to which parallel port.
Tested-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SLIMpro I2C device driver on APM X-Gene platform. This I2C
device driver use the SLIMpro Mailbox driver to tunnel message to
the SLIMpro coprocessor to do the work of accessing I2C components.
Signed-off-by: Feng Kan <fkan@apm.com>
Signed-off-by: Hieu Le <hnle@apm.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
implement bus recovery methods for i2c-omap
so we can recover from situations where SCL/SDA
are stuck low.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The platform_device_id is not modified by these drivers and core uses it
as const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Initialize sysreg by default, otherwise driver will crash in suspend
callback when not using DT.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
Fixes: a7750c3ef0 ("i2c: s3c2410: Handle i2c sys_cfg register in i2c driver")
Jean Delvare