No functional changes.
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Arbitration Lost is an expected situation in a multimaster
environment. I2C controller (IP) correctly detect and report AL.
The only one visible reason for resetting IP in the AL case is
to avoid advisory 1.94 (omap3) and errata i595 (omap4): "I2C:
After an Arbitration is Lost the Module Incorrectly Starts
the Next Transfer".
Errata workaround states: "The MST and STT bits inside I2C_CON
should be set to 1 at the same moment (avoid setting the MST bit
to 1 while STT = 0)." The driver never set MST and STT bits
separately and doesn't create condition for errata. So the reset
is not necessary.
Also corrected return value for AL to -EAGAIN.
Tested on Beagleboard XM C.
Tested on BBB and AM437x Starter Kit by Felipe Balbi.
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In a multimaster environment, after IP software reset, BB-bit value doesn't
correspond to the current bus state. It may happen what BB-bit will be 0,
while the bus is busy due to another I2C master activity.
Any transfer started when BB=0 and bus is busy wouldn't be completed by IP
and results in controller timeout. More over, in some cases IP could
interrupt another master's transfer and corrupt data on wire.
The commit implement method allowing to prevent IP from entering into
"controller timeout" state and from "data corruption" state.
The one drawback is the need to wait for 10ms before the first transfer.
Tested on Beagleboard XM C.
Tested on BBB and AM437x Starter Kit by Felipe Balbi.
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Delete STAT_AD0 mask as unrelated to current IP (omap1?).
Delete DEBUG conditional around SYSTEST masks group.
Add SYSTEST functional mode masks for SCL and SDA.
Add STAT_BF mask.
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The i2c input clock can change dynamically, e.g. on the RK3066 where
pclk_i2c0 and pclk_i2c1 are connected to the armclk, which changes
rate on cpu frequency scaling.
Until now, we incorrectly called clk_get_rate() while holding the
i2c->lock in rk3x_i2c_xfer() to adapt to clock rate changes.
Thanks to Huang Tao for reporting this issue.
Do it properly now using the clk notifier framework. The callback
logic was taken from i2c-cadence.c.
Also rename all misleading "i2c_rate" variables to "clk_rate", as they
describe the *input* clk rate.
Signed-off-by: Max Schwarz <max.schwarz@online.de>
Tested-by: Doug Anderson <dianders@chromium.org> on RK3288
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Since at91sam9g45 is now DT-only, all DMA capable users of this driver
are using the DT case, and the legacy support can be removed.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This allows checkpatch to validate more DTSes.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This allows checkpatch to validate more DTSes.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
It should be the DMA device, not the platform device.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The SCB is present on IMG SoCs other than the META-based TZ1090,
such as the MIPS-based Pistachio SoC. Relax the Kconfig dependency
so that it can be built on any MIPS or META machine.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Acked-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This is a driver for the I2C controller found in Amlogic Meson SoCs.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This makes the topology clearer. For instance, by adding a pca9547
device with address 0x70 to bus i2c-0, you get:
/sys/class/i2c-dev/i2c-0/device/0-0070/channel-0 -> i2c-1
...
/sys/class/i2c-dev/i2c-0/device/0-0070/channel-7 -> i2c-8
Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
[wsa: simplified sysfs-usage and fixed format string usage]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Martin Belanger <martin.belanger@cyaninc.com>
Acked-by: Danielle Costantino <danielle.costantino@gmail.com>
The current implementation creates muxed i2c-<n> busses as immediate
children of their i2c-<n> parent bus. In case of multiple muxes on one
bus, it is impossible to determine which muxed bus comes from which mux.
It could be argued that the parent device should be changed from the
parent adapter to the mux device. This has pros and cons. To improve the
topology, simply add a "mux_device" symlink pointing to the actual
muxing device, so we can distinguish muxed busses. Doing it this way, we
don't break the ABI.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Tested-by: Guenter Roeck <linux@roeck-us.net>
No need to initialize 'ret' if it gets assigned directly after that.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Add dma support for i2c. This function depend on DMA driver.
You can turn on it by write both the dmas and dma-name properties in dts node.
DMA is optional, even DMA request unsuccessfully, i2c can also work well.
Signed-off-by: Yuan Yao <yao.yuan@freescale.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
If the inlcude headers aren't sorted alphabetically, then the
logical choice is to append new ones, however that creates a
lot of potential for conflicts or duplicates because every change
will then add new includes in the same location.
Signed-off-by: Yuan Yao <yao.yuan@freescale.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Since commit 2fd36c5526 ("i2c: core: Map OF IRQ at probe time"),
i2c slaves without interrupts (e.g. da9210 and at24 on r8a7791/koelsch)
fail to probe:
at24: probe of 2-0050 failed with error -22
da9210: probe of 6-0068 failed with error -22
This happens because the call to of_irq_get() in i2c_device_probe()
returns -EINVAL.
If a device node does not have an "interrupts" property,
of_irq_parse_one() fails. Unlike irq_of_parse_and_map(), of_irq_get()
does not ignore errors from of_irq_parse_one(), but forwards them.
Make i2c_device_probe() ignore all errors but -EPROBE_DEFER to fix this,
just like platform_get_irq() and platform_get_irq_byname() already do.
Fixes: 2fd36c5526 ("i2c: core: Map OF IRQ at probe time")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add support for the IMG I2C Serial Control Bus (SCB) found on the
Pistachio and TZ1090 SoCs.
Reviewed-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: James Hogan <james.hogan@imgtec.com>
[Ezequiel: code cleaning and rebasing]
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The driver tried to access device registers with the (little-endian)
iowrite/ioread functions. While this worked on little-endian machines
(e.g. Microblaze with AXI bus), it made the driver unusable on
big-endian machines (e.g. PPC405 with PLB).
During the probe function, the driver tried to write a 32-bit reset mask
into the reset register. This caused an error interrupt on big-endian
systems, because the device detected an invalid (byte-swapped) reset
mask. The result was an Oops.
The patch implements an endianness detection similar to the one used in
other Xilinx drivers like drivers/spi/spi-xilinx.c. It was tested on a
PPC405/PLB system.
Signed-off-by: Thomas Gessler <Thomas.Gessler@exp2.physik.uni-giessen.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
I have a at24 EEPROM connected via i2c bus provided by ISCH i2c
bus driver. This bus driver does not support
I2C_FUNC_SMBUS_WRITE_I2C_BLOCK and so I was looking for a way
to be able to write the eeprom. This patch adds support for
I2C_SMBUS_BYTE_DATA writing via i2c_smbus_write_byte_data.
It is quite slow, but it works.
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
[wsa: s/use_smbuse_write/use_smbus_write/]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
No user needs magic hex values, makes this debug output. Add DMA info.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Make it possible to transfer i2c message buffers via DMA.
Start/Stop/Sending_Slave_Address is still handled using the old state
machine, it is sending the actual data that is done via DMA. This is
least intrusive and allows us to work with the message buffers directly
instead of preparing a custom buffer which involves copying the data
around.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
[wsa: fixed an uninitialized var problem]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Improves readability and reduces chances of duplicates.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Amend the at91 i2c pin controller to set the state of the pins to:
- "default" on resume.
- "sleep" on suspend().
This should make it possible to optimize energy usage for the pins
both for the suspend/resume cycle
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch enforces correct I2C error returned codes from Freescale's
MPC i2c bus driver, allowing for proper user-space/kernel error
handling.
Signed-off-by: Danielle Costantino <danielle.costantino@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Don't log the host status register value in i801_isr(), it has very
little value and fills up the log when debugging is enabled.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There is a control bit in the PCI configuration space which disables
interrupts. If this bit is set, the driver should not try to make use
of interrupts, it won't receive any.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The i2c-i801 driver can work without interrupts, so there is no reason
to make a request_irq failure fatal. Instead we can simply fallback
to polling.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Some systems have been reported to have trouble with interrupts. Use
wait_event_timeout() instead of wait_event() so we don't get stuck in
that case, and log the problem.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
As show in I2C specification:
- Standard-mode: the minimum HIGH period of the scl clock is 4.0us
the minimum LOW period of the scl clock is 4.7us
- Fast-mode: the minimum HIGH period of the scl clock is 0.6us
the minimum LOW period of the scl clock is 1.3us
I have measured i2c SCL waveforms in fast-mode by oscilloscope
on rk3288-pinky board. the LOW period of the scl clock is 1.3us.
It is so critical that we must adjust LOW division to increase
the LOW period of the scl clock.
Thanks Doug for the suggestion about division formulas.
Signed-off-by: Addy Ke <addy.ke@rock-chips.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Max Schwarz <max.schwarz@online.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
When a signal is caught while the i2c-davinci bus driver is
transferring, the driver just "abandons" the transfer and leaves the
controller to fend for itself. The next I2C transaction will find the
controller in an undefined state and often results in a stream of
"initiating i2c bus recovery" messages until the controller arrives in a
defined state. This behaviour also sends out "half" or possibly even
mixed messages to I2C client devices which may put them in an undesired
state as well. So, let's get simply uninterruptible.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Drivers should put the device into low power states proactively whenever the
device is not in use. Thus implement support for runtime PM and use the
autosuspend feature to make sure that we can still perform well in case we see
lots of i2c traffic within short period of time.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
I2C clients instantiated from OF get their IRQ mapped at device
registration time. This leads to the IRQ being silently ignored if the
related irqchip hasn't been proved yet.
Fix this by moving IRQ mapping at probe time using of_get_irq(). The
function operates as irq_of_parse_and_map() but additionally returns
-EPROBE_DEFER if the irqchip isn't available, allowing us to defer I2C
client probing.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The function will be used by the I2C core which can be compiled as a
module.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add support for r8a73a4 (R-Mobile APE6) and sh73a0 (SH-Mobile AG5).
On these SoCs, the operating clock runs faster that on previous SoCs,
and the internal SCL clock counter gets incremented every 2 clocks of
the operating clock, just like on R-Car Gen2.
Cfr. the "/2" in the calculation of ICCL/ICCH in section "I2C Bus
Interface (IIC)", subsection "Transfer Rate" of the datasheets.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Explicitly list the various SoC-specific compatible properties.
This allows checkpatch to validate DTSes.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
According to Documentation/CodingStyle - Chapter 14:
"The preferred form for passing a size of a struct is the following:
p = kmalloc(sizeof(*p), ...);
The alternative form where struct name is spelled out hurts readability and
introduces an opportunity for a bug when the pointer variable type is changed
but the corresponding sizeof that is passed to a memory allocator is not."
So do it as recommeded.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
- enable bpf syscall for compat
- cpu_suspend fix when checking the idle state type
- defconfig update
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=CBMO
-----END PGP SIGNATURE-----
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
- enable bpf syscall for compat
- cpu_suspend fix when checking the idle state type
- defconfig update
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: defconfig: update defconfig for 3.18
arm64: compat: Enable bpf syscall
arm64: psci: fix cpu_suspend to check idle state type for index
Another quiet week:
- A fix to silence edma probe error on non-supported platforms from Arnd
- A fix to enable the PL clock for Parallella, to make mainline usable with
the SDK.
- A somewhat verbose fix for the PLL clock tree on VF610
- Enabling of SD/MMC on one of the VF610-based boards (for testing)
- A fix for i.MX where CONFIG_SPI used to be implicitly enabled and now needs
to be added to the defconfig instead
- Another maintainer added for bcm2835: Lee Jones
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=bOlr
-----END PGP SIGNATURE-----
Merge tag 'armsoc-for-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Another quiet week:
- a fix to silence edma probe error on non-supported platforms from
Arnd
- a fix to enable the PL clock for Parallella, to make mainline
usable with the SDK.
- a somewhat verbose fix for the PLL clock tree on VF610
- enabling of SD/MMC on one of the VF610-based boards (for testing)
- a fix for i.MX where CONFIG_SPI used to be implicitly enabled and
now needs to be added to the defconfig instead
- another maintainer added for bcm2835: Lee Jones"
* tag 'armsoc-for-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: dts: zynq: Enable PL clocks for Parallella
dma: edma: move device registration to platform code
ARM: dts: vf610: add SD node to cosmic dts
MAINTAINERS: update bcm2835 entry
ARM: imx: Fix the removal of CONFIG_SPI option
ARM: imx: clk-vf610: define PLL's clock tree
Pull devicetree bugfix from Grant Likely:
"One buffer overflow bug that shouldn't be left around"
* 'devicetree/merge' of git://git.kernel.org/pub/scm/linux/kernel/git/glikely/linux:
of: Fix overflow bug in string property parsing functions
Pull btrfs fix from Chris Mason:
"It's a one liner for an error cleanup path that leads to crashes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: fix kfree on list_head in btrfs_lookup_csums_range error cleanup
Here are 3 tiny fixes for 3.18-rc4. One fixes up a long-stading race
condition in the driver core for removing directories in
/sys/devices/virtual/ and the other 2 fix up the wording of a new
Kconfig option that was added in 3.18-rc1.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlReZX4ACgkQMUfUDdst+ym9/gCfbVnQzjAEh3OL0I+mTMjAMxhX
AwwAoK1f/ZK02U/vz/u/dpK38LM3FhH+
=Q4mc
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fixes from Greg KH:
"Here are 3 tiny fixes for 3.18-rc4.
One fixes up a long-stading race condition in the driver core for
removing directories in /sys/devices/virtual/ and the other 2 fix up
the wording of a new Kconfig option that was added in 3.18-rc1"
* tag 'driver-core-3.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
tiny: rename ENABLE_DEV_COREDUMP to ALLOW_DEV_COREDUMP
tiny: reverse logic for DISABLE_DEV_COREDUMP
sysfs: driver core: Fix glue dir race condition by gdp_mutex
Here are some staging/iio fixes for 3.18-rc4.
Nothing major, just a few bugfixes of things that have been reported.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlReZfMACgkQMUfUDdst+ylycwCdGD/ZN7f6rBq7EG0YqBngs5zX
AWwAoK+l0zqYCQ6N8s+ZnQ7l1Ijo7HhR
=vEmW
-----END PGP SIGNATURE-----
Merge tag 'staging-3.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver fixes from Greg KH:
"Here are some staging/iio fixes for 3.18-rc4.
Nothing major, just a few bugfixes of things that have been reported"
* tag 'staging-3.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging:iio:ade7758: Remove "raw" from channel name
staging:iio:ade7758: Fix check if channels are enabled in prenable
staging:iio:ade7758: Fix NULL pointer deref when enabling buffer
iio: as3935: allocate correct iio_device size
io: accel: kxcjk-1013: Fix iio_event_spec direction
iio: tsl4531: Fix compiler error when CONFIG_PM_OPS is not defined
iio: adc: mxs-lradc: Disable the clock on probe failure
iio: st_sensors: Fix buffer copy
staging:iio:ad5933: Drop "raw" from channel names
staging:iio:ad5933: Fix NULL pointer deref when enabling buffer
Alexander Kochetkov