ioatdma by default is in snoop mode. Relaxed ordering according to spec
does not do anything in snoop mode. However, it causes hang or significant
performance degrade when tested with NTB. Disabling in the driver due to
some BIOS do not configure it correctly.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Currently the following DT description would result in dmac0 always
being tried first and dmac1 second if dmac0 was unavailable. This
results in heavier use of dmac0 then of dmac1. This patch adds an
approximate average distribution over the two nodes lessening the load
of anyone of them.
i2c6: i2c@e60b0000 {
...
dmas = <&dmac0 0x77>, <&dmac0 0x78>,
<&dmac1 0x77>, <&dmac1 0x78>;
dma-names = "tx", "rx", "tx", "rx";
...
};
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The IS_ENABLED() macro checks if a Kconfig symbol has been enabled either
built-in or as a module, use that macro instead of open coding the same.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When the ccerr handler is called but the error registers indicate no error
events we need to command eDMA to re-evaluate the errors. Otherwise we can
receive flood of error interrupts.
Reported-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In order to create a relationship model between the channels and the
management object, we are adding support for object hierarchy to the
drivers. This patch simplifies the userspace application development.
We will not have to traverse different firmware paths based on device
tree or ACPI based kernels.
No matter what flavor of kernel is used, objects will be represented as
platform devices.
The new layout is as follows:
hidmam_10: hidma-mgmt@0x5A000000 {
compatible = "qcom,hidma-mgmt-1.0";
...
hidma_10: hidma@0x5a010000 {
compatible = "qcom,hidma-1.0";
...
}
}
The hidma_mgmt_init detects each instance of the hidma-mgmt-1.0 objects
in device tree and calls into the channel driver to create platform devices
for each child of the management object.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Add debugfs hooks for debugging the execution behavior of the DMA
channel. The debugfs hooks get initialized by the probe function and
uninitialized by the remove function.
A stats file is created in debugfs. The stats file will show the
information about each HIDMA channel as well as each asynchronous job
queued and completed at a given time.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch implements the hardware hooks for the HIDMA channel driver.
The main functions of interest are:
- hidma_ll_init
- hidma_ll_request
- hidma_ll_queue_request
- hidma_ll_hw_start
OS layer calls the hidma_ll_init function during probe to set up the
hardware. At this moment, the number of supported descriptors are also
given. On each request, a descriptor is allocated from the free pool and
filled in with the transfer parameters. Multiple requests can be queued
into the hardware via the OS interface. When client is ready for requests
to be executed, start method is called.
Completions are delivered via callbacks via tasklet.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
When check for capabilities recognize slave support by either DMA_SLAVE or
DMA_CYCLIC bit set. If we don't do that the user can't get a normally worked
DMA support for engines that doesn't have one of the mentioned bits set.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Armada 3700 SoC uses the mv_xor driver but don't select anymore the
PLAT_ORION symbol. This commit extends the dependency of the mv_xor
driver to the more modern SoCs only compatible with ARCH_MVEBU, which
allows using it with the Armada 3700 SoC.
In the same time it also add the COMPILE_TEST dependency allowing a wider
test coverage.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Armada 3700 SoC comprise a single XOR engine compliant with the ones used
in older Marvell SoC's like Armada XP or 38x. The only thing that needs
modification is the Mbus configuration, which has to be done on two
levels: global and in device. The first one is inherited from the
bootloader. The latter can be opened in a default way, leaving
arbitration to the bus controller. Hence filled mbus_dram_target_info
structure is not needed.
Patch "dmaengine: mv_xor: optimize performance by using a subset
of the XOR channels" introduced limitation for using XOR engines and
channels vs number of available CPU's. Those constraints do not however
fit Armada 3700 architecture with two possible CPU's and single,
dual-channel engine. Hence in this commit an adjustment for setting
maximum available channels is added.
This patch enables XOR access to DRAM by opening default window to 4GB
space with specific attribute.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Currently the main difference between legacy XOR engine and newer one, is
the way the engine modes are setup (either in the descriptor or through
the controller registers). In order to be able to take into account new
generation of the XOR engine for the ARM64 SoC, we need to identify them
by type, and then depending to the type the engine setup will be
selected.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Fix two warnings which appear when building for 64 bits target:
drivers/dma/mv_xor.c: In function ‘mv_xor_prep_dma_xor’:
drivers/dma/mv_xor.c:480:3: warning: format ‘%u’ expects argument of type ‘unsigned int’, but argument 6 has type ‘size_t {aka long unsigned int}’ [-Wformat=]
"%s src_cnt: %d len: %u dest %pad flags: %ld\n",
^
drivers/dma/mv_xor.c: In function ‘mv_xor_probe’:
drivers/dma/mv_xor.c:1223:17: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
op_in_desc = (int)of_id->data;
^
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Dma_pool_zalloc combines dma_pool_alloc and memset 0. The semantic patch
that makes this transformation is as follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression d,e;
statement S;
@@
d =
- dma_pool_alloc
+ dma_pool_zalloc
(...);
if (!d) S
- memset(d, 0, sizeof(*d));
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Dma_pool_zalloc combines dma_pool_alloc and memset 0. The semantic patch
that makes this transformation is as follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression d,e;
statement S;
@@
d =
- dma_pool_alloc
+ dma_pool_zalloc
(...);
if (!d) S
- memset(d, 0, sizeof(*d));
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Dma_pool_zalloc combines dma_pool_alloc and memset 0. The semantic patch
that makes this transformation is as follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression d,e;
statement S;
@@
d =
- dma_pool_alloc
+ dma_pool_zalloc
(...);
if (!d) S
- memset(d, 0, sizeof(*d));
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The transfer direction is now checked in set_config.
There is no need to check it twice.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Some DMA clients, as audio, don't set the maxburst size and bus width
on the memory side when starting DMA transfers.
This patch prevents such transfers to be aborted by providing system
default values to the lacking ones.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
We pass struct dw_dma_chip to dw_dma_probe() anyway, thus we may use it to
pass a platform data as well.
While here, constify the source of the platform data.
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Keep the entire platform data in the struct dw_dma.
It makes the driver a bit cleaner.
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
There several changes are done here:
- Convert the property to be in bytes
Besides that this is a common practice for such property, the use of a value
in bytes much more convenient than handling the encoded one.
- Rename data_width to data-width in the device tree bindings
The change leaves the support for the old format as well just in case someone
will use a newer kernel with an old device tree blob.
- While here, replace dwc_fast_ffs() by __ffs()
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The value of nr_masters equal to 0 is invalid since this DMA controller has to
have at least one master.
Check this before we proceed with the rest of properties.
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Fix typo in warning message that there is no "interrupt-names"
property defined in the device-tree and legacy-mode is used.
Also added newline to end of message.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Checking the DMA config before setting the lli list avoids to do tests
inside the setting loop.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In the commit 1f9cd915b6 ("dmaengine: sun6i: Fix memcpy operation"),
the signed values returned by convert_burst() and convert_buswidth()
were stored in an unsigned value.
Then, these values were considered as errors when non null.
As a result, DMA transfers were rejected when the burst or buswidth
had values different from 1, as 8 for the burst or 4 for the bus width.
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The IRQ register number is computed, but this number was not used
and the register was the one indexed by the channel index instead.
Then, only the first DMA channel was working.
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
In the current state, upon bus error the driver will spin endlessly,
relaunching the last tx, which will fail again and again :
- a bus error happens
- pxad_chan_handler() is called
- as PXA_DCSR_STOPSTATE is true, the last non-terminated transaction is
lauched, which is the one triggering the bus error, as it didn't
terminate
- moreover, the STOP interrupt fires a new, as the STOPIRQEN is still
active
Break this logic by stopping the automatic relaunch of a dma channel
upon a bus error, even if there are still pending issued requests on it.
As dma_cookie_status() seems unable to return DMA_ERROR in its current
form, ie. there seems no way to mark a DMA_ERROR on a per-async-tx
basis, it is chosen in this patch to remember on the channel which
transaction failed, and report it in pxad_tx_status().
It's a bit misleading because if T1, T2, T3 and T4 were queued, and T1
was completed while T2 causes a bus error, the status of T3 and T4 will
be reported as DMA_IN_PROGRESS, while the channel is actually stopped.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch changes the driver to allocate DMA descriptors when
needed. This stops memory resources to be wasted and letting
them sit idle in the free_list structure when the device doesn't
need it... This also solves the problem, that a driver has to
guess the number of how many descriptors it needs to allocate
in advance. Currently, the dma engine will just fail when put
under load by sata_dwc_460ex.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
It seems that the define has not been with acurate name and
makes confusion while reading the code. The more acurate
name should be BAM_FIFO_SIZE.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The pipe fifo size register must instruct the bam hw
how many hw descriptors can be pushed to fifo. Currently
we instruct the hw with 32KBytes but wrap the tail in
bam_start_dma in BAM_P_EVNT_REG on 4095 i.e. 32760. This
leads to stalled transactions when the tail wraps.
Fix this by use the correct fifo size in BAM_P_FIFO_SIZES
register i.e. 32K - 8.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Some of the peripherals has bam which is controlled by remote
processor, thus the bam dma driver must avoid register writes
which initialise bam hw block. Those registers are protected
from xPU block and any writes to them will lead to secure
violation and system reboot.
Adding the contolled_remotely flag in bam driver to avoid
not permitted register writes in bam_init function.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Tested-by: Pramod Gurav <gpramod@codeaurora.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Extend BAM dt bindings with controlled-remotely property. The
property will be needed to handle cases where we need to skip
register writes to initialise BAM hardware block.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Currently we write BAM_IRQ_CLR register with zero even when no
BAM_IRQ occured. This write has some bad side effects when the
BAM instance is for the crypto engine. In case of crypto engine
some of the BAM registers are xPU protected and they cannot be
controlled by the driver.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Tested-by: Pramod Gurav <gpramod@codeaurora.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Add interrupt-names properties to dt and apply the correct
mapping between irq and dma channels.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Use platform_get_irq_byname to allow for correct mapping of
interrupts to dma channels.
The currently implemented device tree is unfortunately
implemented with the wrong assumption, that each dma-channel
has its own dma channel, but dma-irq 11 is handling
dma-channel 11-14 and dma-irq 12 is actually a "catch all"
interrupt.
So here we use the byname variant and require that interrupts
are explicitly named via the interrupts-name property in the
device tree.
The use of shared interrupts is also implemented.
As a side-effect this means we can now use dma channels 12, 13 and 14
in a correct manner - also testing shows that onl using
channels 11 to 14 for spi and i2s works perfectly (when playing
some video)
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Acked-by: Eric Anholt <eric@anholt.net>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Added standard interrupt-names property so that
platform_get_irq_byname() can get used to fetch the
interrupt corresponding to each dma_channel
instead of the current platform_get_irq() with
an assumed ordering of the interrupts.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Eric Anholt <eric@anholt.net>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Also added check for an error condition in bcm2835_dma_create_cb_chain
that showed up during development of this patch.
Tested using dmatest for all enabled channels.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Add slave_sg support to bcm2835-dma using shared allocation
code for bcm2835_desc and DMA-control blocks already used by
dma_cyclic.
Note that bcm2835_dma_callback had to get modified to support
both modes of operation (cyclic and non-cyclic).
Tested using:
* Hifiberry I2S card (using cyclic DMA)
* fb_st7735r SPI-framebuffer (using slave_sg DMA via spi-bcm2835)
playing BigBuckBunny for audio and video.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Vinod Koul